INSTRUCTION MANUAL

< Optional Software >

DIGITAL MINILAB
FRONTIER 500
VARIETY PRINT SOFTWARE
TEMPLATE EDITING TOOL

[S3] Ver.2.0 or later First Edition

PP3-B1174E
 INTRODUCTION

This Installation/Instruction Manual contains operating instructions for the “Template Editing Tool”
dedicated for the Fujifilm Digital Minilab FRONTIER 500.

• To ensure proper use and optimum performance of the software, read this manual thoroughly.

• This manual should be kept in a fixed place near the machine so that it can be referred to at any
time a point needs to be clarified.

• The enclosed “END-USER LICENSE AGREEMENT” should be read carefully before you use this
software.

• To use this software, Photoshop Ver.7.0 or later is required.

• In this “Template Editing Tool”, the template for mounted print (except a calendar) with Variety
Print Software [S3] in use can be created.

• Template Editing Tool is available when the software is installed into the DIGITAL IMAGING
CONTROLLER II (hereafter DIC II) or an other personal computer. Before installing or when
using this software on the DIC II, quit the DIC II Basic Software [S2].

*Photoshop® is registered trademark of Adobe Systems Incorporated.

*Windows® is registered trademark of the Microsoft Corporation.

1.Electro-optical-mechanical reproduction of this manuscript is strictly forbidden.

2.Product innovations may result in specification changes without prior notice.
CONTENTS

1 Installation ................................................................................................................. 4

2 Basic Operation....................................................................................................... 7
2.1 Base Editing........................................................................................................ 7
2.2 Creating of Templates......................................................................................... 13
2.3 Registration into FRONTIER 500........................................................................ 21

3 Applied Operations ................................................................................................ 24

3.1 Inserting of Mask into Picture Area ..................................................................... 24
3.1.1 Optional Mask Images .......................................................................... 24
3.1.2 Procedures for Inserting Mask .............................................................. 25
3.2 Editing of Background Color ............................................................................... 29
3.3 Area Layout......................................................................................................... 32
3.3.1 Use of Overlap Switching Buttons ........................................................ 32
3.3.2 Aligning of Area..................................................................................... 35
3.3.3 Area Positioning .................................................................................... 39
3.4 Editing of Existing Variety Templates ................................................................. 41
3.5 Reference Materials for Operations .................................................................... 45
3.5.1 Print Size/Base Size/Pixel Reference Table ......................................... 45
3.5.2 Types of Sample Templates ................................................................. 46
3.5.3 Using the Sample Templates ................................................................ 47
3.6 Using the HELP Screen ...................................................................................... 51

4 Customizing.............................................................................................................. 53
4.1 File ...................................................................................................................... 53
4.2 Editing ................................................................................................................. 55
4.3 Tool ..................................................................................................................... 57
4.4 Test Image .......................................................................................................... 58
4.5 Test Text ............................................................................................................. 59

5 Troubleshooting...................................................................................................... 60
5.1 Messages and Countermeasures ....................................................................... 60
5.2 Uninstallation ...................................................................................................... 66
5.2.1 Uninstallation Using Installer CD .......................................................... 66
5.2.2 Uninstallation with Desktop Screen ...................................................... 69

3
 1 Installation

Install the Template Editing Tool.

Install it on the DIC II or your personal computer. When installing Template Editing Tool software
into the DIC II, quit the DIC II Basic Software [S2] by using “Post-operational checks.”

System Requirements: Windows XP machine with a CPU more than 512MHz and HD capacity
greater than 100MB

1 Set the Template Editing Tool installer CD in the

CD drive.

2 On the Desktop, select [Start] - [Run].

Select [Start]-[Run].

Select [Setup].

3 In the “Run” screen, click the [Browse] button to

open the [Template Editing Tool] folder in the
CD drive, and then select [Setup]. Then, click
the [Open] button.

Click the [Open] button.

Check that [E:\Template Editing Tool\Setup.exe]

is displayed.

4 In the “Run” screen, check that [E:\Template

Editing Tool\Setup.exe] is displayed in the
[Open] box, and then click the [OK] button.

The drive letter (ex: E:) varies depending on your PC.

Click.

4
 5 “Preparing installer...” message appears.

6 After a few seconds, the installer main screen

appears.

7 In the installer main screen, click the [Install]

button, and then click the [OK] button.

If the [Cancel] button is clicked in the installer

main screen, the confirmation screen appears.
To cancel the installation, click the [OK] button.

Click the [Install] button. Click.

To cancel the installation,

click the [OK] button.

5
 8 The installation confirmation screen appears.
Click the [OK] button.

Click the [OK] button.

9 Installation starts.

10 The installation completion screen appears.

Remove the Template Editing Tool installer CD
from the CD drive.
Click the [OK] button.

Click the [OK] button.

6
 2 Basic Operation
The chapter explains how to create a template using the [template edit tool] installed on your
personal computer.

2.1 Base Editing

1 In the Desktop screen, select [Start] -

[Programs] - [FDi] - [Template Editing Tool] -
[Template Editing Tool].

Select [Start]-[Programs]-[FDi]-
[Template Editing Tool]-[Template Editing Tool].

You can also start up the program by double-clicking the

shortcut icon previously set in the Desktop screen.

Double-click.

2 The Template Editing Tool main screen appears.

IMPORTANT
Special care must be taken when using any
copyright -protected product (such as certain
image data or pictures) .

7
 3 In the menu bar, select [File] - [New].

Select [File] - [New].

4 In the “Header/Base Edit” screen, select one of

the template groups to be edited in the
[Template Group].

IMPORTANT
A template which mount the same picture in a
number of sizes of frame like the package print
needs to mount the same picture with a number
of frames.
IMPORTANT
In Package print, you can place up to 32 frames
to be mounted on the template when they are of
the same size.

The [Template Group] is the group name that is to be

Select the template group.
used for the Mounted Print in the FRONTIER 500.
If you select [Custom], you can make an original
template with a name of your choosing.
Enter the [Template Name].

5 Enter any name in the [Template Name].

The template name must be one that the operator will

be able to recognize when he/she uses it.

The file name must be within 30 characters and it is

recommended to be a name that will be easy to
manage later.

IMPORTANT
Blank characters(spaces) cannot be entered
between the characters.

8
 If you click [...] button in [Template Group] field, the
following dialog box is displayed. You can add or delete
the template in it.

Enter the [Template No.].

6 Enter the [Template No.].

The template number must be one that the operator will

be able to recognize when he/she uses it.

The file name must be within 20 characters and it is

recommended to be a name that will be easy to
manage later.

IMPORTANT
Blank characters(spaces) cannot be entered
between the numbers.

9
 7 Select any size in the [Paper Size Name] that is
later referred as the print size.

Select the [Paper Size Name].

You can select the width and height freely by selecting

[Free] for [Paper Size Name]. When selecting [Free],
note that the width and height limitations vary
depending on your printer.

When selecting [Free], you can select

the width and height freely.

10
 8 Select the orientation of the base to be made
by adding a checkmark [✔] to the [Portrait] or
[Landscape] radio button.

Select the orientation.

In the [Base Edit Value], the size that is larger than the
actual for eclipse occurrence is displayed.

Size larger than the actual for eclipse

occurrence.

11
 9 In case of a bordered print with some space left
within the base, set the margins for each side.

If necessary, set the margins.

10 Upon completion of settings, click the [OK]

button.

Click.

11 The base is displayed in the main screen.

[Example of 5 mm margins] [Example of 0 mm margins]

12
 2.2 Creating of Templates
Create a template. The following is an example of creating a simple custom template. If you use the
functions such as mask insertion or gradation effects, see “3 Applied Operations”.

Picture Area
( [PICT] frame : edit with [PICT] button) Title Area
This is the frame for mounting the user's picture. ( [TITLE] frame : edit with [TITLE] button)

Good friend mountain

climbing memory

Image Area
( [IMG] frame : edit with [IMG] button)
This is the frame for mounting the image,
which is for setting the logo and the template.

The following procedures for creating a template mainly

use the one-touch button operations.

1 Display the image, picture or title areas by

clicking the [IMG], [PICT] or [TITLE] button.

IMPORTANT
The [PICT] will be mounted in Variety Print[S3]
in FRONTIER 500 by using the same aspect
Display the image, picture or ratio as when it was created. So if you try to
title areas by clicking any of
the three buttons. mount the image having a different ratio in
FRONTIER 500, the orientation of the image
may be changed. To prevent this , you may
have to crop the image to fit the frame size
beforehand.

13
 ■ Information regarding Base Area

The white area in the screen is the base

area. It is recommended that you create the
template using the whole screen.

The area within the bold gray line is the one that is
not eclipsed(masked) when printing the no-border
picture. The outside of the bold line indicates the
printing size.

You can set the margins properly by referring to

the solid line, so that the margins are always
located outside the solid line, when you set the
Base Margin
margin values from the sides.

2 First, let’s insert the image in the Image Area.

Click the [IMG] button on the tool bar to select
the image file in the default folder
[C:\TplEdit\_Library\Image].

This is the image, which is the mount as an actual

template.You cannot change the size of the image file. It
must be created in the image processing software
beforehand.
Select the image.
An image sample file is prepared in the software, but
normally create a new image file for the template before
calling it from the [IMG] or by the image area call
command.

It is the condition, which is opened two original

images in the image area.

14
 Create an original image file using the image
processing software such as Photoshop.

For the pixel size for the image to be created, see

“3.5.1 Print Size/Base Size/Pixel Reference Table”.

3 Next, set the area frame in the picture area that

user image inserts.
Click the [PICT] button on the tool bar, to display
the picture area on the base.

Click the [PICT] buttons.

4 Adjust the size of the picture area, and then

position this area in the desired place. (You can
also set the detailed settings such as mask
choice or picture property settings by double-
clicking the area directly when it is selected.)

Adjust the size of area.

FRONTIER and Image Controller treats up to 4.

5 Click the [TITLE] button on the tool bar, to

display the title area on the base.
(Double-click the area directly when it is
selected, to make detailed settings. Here you
can also change the font size and check the
available number of characters.)

The title text can be entered by selecting [Customize] -

[Test Text].

Up to 4 titles can be input in the title area with

FRONTIER 500.

15
 Align the areas roughly.

6 Align the frame of the picture area with that of

the image area using the mouse. In this step,
align them only roughly.

Order of pile for loaded [PICT] frame, [IMG]frame and

[TITLE] frame automatically becomes [IMG](lowest)
|[PICT] |[TITLE].In the back frame is hidden by the
front frame, loaded image/in order not hidden the image
by front frame, configuration is necessary for avoiding
overlapping the frame.

■ Area Frame Alignment

If the areas are not adjusted correctly, the

misalignment of the areas can be seen when
printing.

Position the picture area and image area

completely over the base (white area).

Create the title area so that it falls within the gray

line.

When [View] - [500%] is selected.

(1)Alignment Check by Enlargement

• Select [View] - [500%].

First, the position adjustment is done roughly with the

image enlarged 500%. Then it is set accurately by
using an enlargement of 1000%.

16
 • Select [View] - [1000%].
When [View] - [1000%] is selected.
To align the areas exactly, a 1000% enlargement
is required.

Two lines appear as a dotted line. The illustration at the left indicates that the
upper, left-hand and right-hand frames are
exactly aligned( frame and frame ). If
the two frame lines are correctly
overlapped, they appear as a dotted line.

If the image area exceeds the base area, it can

still be fit within the base by selecting [View] - [Fit].

(2)Area Adjustment by Arrow Keys

Adjust the area by steps of 1 pixel each,

using the arrow keys. Select the area frame
to be used and then click one of the arrow
buttons.

Adjust the area by 1 pixel

with the arrow keys.

By selecting [View] - [Fit], the base can be

adjusted to fit in the screen.

17
 • The frame of the shifted area becomes a
dotted line consisting of red and blue dots.

Overlap two lines.

Two lines become a dotted lines.

Instead of the arrow buttons, you can also use the

arrow keys in the keyboard to move the area when
the mouse cursor is the cross.

Cursor becomes [ ] mark.

To fine-adjust one side of a frame, align the
mouse cursor with the rectangular mark in the
center of the side. When the cursor becomes the
[ ] mark, use the arrow keys of the keyboard to
change the size of the frame.

Click the [Test View] button.

7 In order to check the positioned "PICT" frame,
the "IMG" frame, the "TITLE" frame, etc. with
the picture (test picture) prepared beforehand,
click the [Test View] button.

18
Finished image is displayed.

8 A finished image is displayed.

Check the position.
• [IMG] frame:
The picture which was set up as the [IMG] frame
• The picture of the [PICT] frame:
The test picture that was prepared beforehand. In
practice, set the user’s image with Variety Print
Software.
• The wording of the [PICT] frame:
The text for the test that was prepared
beforehand. In practice, set the title using the
Variety Print Software.

Test images disappear.

9 When the position is good, click the [Test View]
button again to make the image disappear, and
save the data. When changing a position, re-
edit after canceling test composition, and then
check Procedures 7 and 8.

Select [File] - [Save As].

10 Let's save the created template.
Select [File] - [Save As].

19
 Enter a file name.

11 When the “Save/Save As” screen appears,

enter a file name and path in the [Destination
Parent] box, and then click the [OK] button.

If you save the template in other media, click the [...]

button in the right-hand side of [Destination Parent], and
then select the drive.

Click.

When registering the created template in the

FRONTIER 500, it is convenient to save it in a FD.
When saving in a CD-R, after saving it in the optional
folder temporally, write it into a separated CD-R .

12 In the confirmation screen, click the [OK] button.

Click.

13 To close the program, select [File] - [Exit].

Select [File] - [Exit].

20
 2.3 Registration into FRONTIER 500

Register the created template into the FRONTIER 500 in the menu [Setup and Maintenance] after
saving it in a FD or CD-R.

1 Insert the FD including the created template

into the FD drive of the FRONTIER 500.
(In case of a CD-R, use the CD drive.)

EZ041

Select [Setup and Maintenance].

2 In the “Main Menu” screen, select [Setup and

Maintenance].

Enter ‘0000’.
3 In the “Login” screen, enter ‘0000’ in the
[Password] field, and then click the [OK] button.
(for Laboratory Manager log-in)

Click.

21
 Click.
4 In the “Setup and Maintenance” screen, select
[(10) Register/Delete] - [(1021) Template Regist/
Delete].

Click.

5 The “Template Regist/Delete [1021]” screen

appears.

Click.

6 In the “Template Regist/Delete [1021]” screen,

select [Regist] as [Function Select].

22
Select [A:] for [Source].
7 The drive which corresponds with the FD at
[Source] is selected (Here,[A:]).
(In case of a CD-R, select [N:].)

8 Select the created template, and then click the

[OK] button.

Click.

9 Remove the FD from the FD drive.

(In case of a CD-R, remove it from the CD
drive.)

When using the registered template, first select the print

size and then check it, so that you can easily display
and use it. After that, do the same procedures as for
Mounted Print.

EZ042

23
 3 Applied Operations

3.1 Inserting of Mask into Picture Area

3.1.1 Optional Mask Images

A picture area with a loaded image can be edited by using any of the following mask image.
The following 9 mask images are available for the Template Editing Tool.

q arch.png w heart.png e circle.png

r roundsquare.png t polygon5.png y star.png

u explosion.png i polygon8.png o diamond.png

The above 9 mask images are stored in the folder [C:\TplEdit\_Library\Mask].

24
3.1.2 Procedures for Inserting Mask

1 To display the [Picture Area Properties] screen,

select [View] - [Properties Display] or double-
click the picture area itself.

Select [View] - [Properties Display].

2 In the “Picture Area Properties” screen, click the

[...] button to select any of the mask images.

You can also select the mask image by entering the

path name for the image directly in the [Mask Image
File] box.

Click.

Select one of the mask images.

3 In the “Open” screen, select a mask image, and
then click the [Open] button.

Click.

25
 Click.
4 In the “Picture Area Properties” screen, click the
[Close] button.

If you click the [Fit] button in the “Picture Area

Properties” screen, the magnification ratio of the mask
is fixed to 100% in proportion to the picture area.

Select [View] - [Mask Display].

5 Select [View] - [Mask Display] in the tool bar.

The selected mask appears.

6 The selected mask appears in the picture area.

26
■Mask Creation

To create an original mask, use the following procedure. The following is the procedure of
using the Photoshop.

Create a 512 × 512 pixel file.

(1)Select [File] - [New], and then create a
512 X 512 pixel file, and then click the
[OK] button.

IMPORTANT
Make sure to select [Gray Scale] as Mode.

Create the desired mask shape.

(2)Select the tool in the tool box, and then
create the desired mask shape.

(3)A boundary line is scumbled in order to

make the surroundings of a mask
conform with the image.
Select [Select] - [Feather], and then set
Set up the feather value (ex:10). up the proper value for feather (Ex: 10),
and then click the [OK] button.

If you do not add the feather effect, select [0].

27
 (4)Black out the part where the image is
inserted, specified the place.
Select [Edit] - [Fill], and then select
[100%] for [Opacity], then click the [OK]
button.

Select [100%] for [Opacity].

(5)Select [File] - [Save As] to save the file

with the [PNG] format in the
[C:\TplEdit\_Library\Mask].

In the “PNG Options” screen, select [NO] for

[Interlace] and then click the [OK] button.

Save the mask file with PNG format.

28
 3.2 Editing of Background Color

The background color of the mount can be set up. You can change the color of the background and
also add the gradation effect to it.

Select [File] - [Background Edit].

1 Select [File] - [Background Edit].

Click.
2 In the “Background Edit” screen, click the white
button in the [Background Color] field to change
the background color.

29
 Select the desired color.
3 In the “Color” screen, select the desired color,
and then click the [OK] button.

Click.

Add the check.

4 To select the gradation effect, check [✔] the

[Create, change or delete the gradation] box,
and then select the gradation pattern and start/
end color.

5 Click the [OK] button.

Click.

30
Background is set up.

6 The background is set up.

If you do not want to change the background image,

select [File] - [Background Protect] and then the
background is set and cannot be changed.

Select [File] - [Background Protect].

31
 3.3 Area Layout

3.3.1 Use of Overlap Switching Buttons

By using these buttons, a selected image can be switched to the upper or lower position. In that
case, although the PICT name changes, the frame number and screen state do not state do not
change.

Click this to increase the number of [PICT].

Click this to decrease

the number of [PICT].

NOTE: Before changing the order or overlapping, make sure that the picture area number is contin-
uous.

Pict 1 Pict 2

Pict 3 Pict 4

A larger [PICT] number is usually on the smaller one.

The frame number in the [Picture Area Properties] screen is not changed after a change in the order of image overlap-
ping.

32
[Example]
There are four picture area frames on the base.

Upper Frames: Pict 1 | Pict 2

Lower Frames : Pict 3 | Pict 4

In the case when Pict 3 is on top of Pict 1

Pict 1 Pict 2

Pict 3 Pict 4

Pict 3 is on top of Pict 1.

In each case, The [PICT] frame with the larger number is on top of the framewith the smaller number.

1 Select the smaller [PICT] frame ([Pict3]), and

then click the [Behind] button.

Click the [Behind] button.

33
 Pict 1 Pict 3

2 The [PICT] frame number Pict 3 is changed to

Pict 2. The result is as follows.

Upper Frames:Pict 1 | Pict 3

Lower Frames:Pict 2 | Pict 4

Pict 2 Pict 4

Click the [Behind] button again.

3 Click the [Behind] button again.

4 Now, the smaller [PICT] frames are under the

larger one.
Pict 2 Pict 3 Pict 2 Pict 3

Pict 1 Pict 4 Pict 1 Pict 4

Pict 2 is on top of Pict 1.

34
3.3.2 Aligning of Area

To align the frames, more than two frames must be selected beforehand.

Decide the following conditions.

a. Range of aligning areas (Ex: Fit in base)

b. Type of area and numbers (Ex: 16 picture areas)
c. Area numbers in length and breadth (Ex: 4 × 4)

Display the areas.

1 Display the areas to be aligned on the base. In

this step, align them freely. (Ex: 16 picture areas
with the same size.)

NOTE: Alignment can only be done with areas

of the same size. If areas of different
sizes are mixed, arrange them into
group of areas having the same size,
and then align them.

Move [PICT 1] to upper left-hand corner.

2 Move one of the areas to one side of the base.

(Ex: [PICT1] toward the upper left-hand corner
of the base.)

35
 3 Move one of the other areas (except the area
you moved in the Step 3) to the side diagonal to
that used in Step 3. (Ex: [PICT16] that is, toward
the lower right-hand corner of the base.)

Move [PICT 16] to lower right-hand corner.

4 Select all the areas to be aligned. (Enclose all

the areas or click the areas one by one while
pressing the [Shift] key.)

Select all areas.

Select [Layout] - [Alignment].

5 Select [Layout] - [Alignment].

36
Enter number of areas in the
horizontal and vertical direction.
6 Enter number of areas in the horizontal and
vertical. (Ex: [Horizontal]: 4/[Vertical]: 4)

Select aligning order.

7 Select the aligning order: horizontally or
vertically.

8 Click the [OK] button.

Click.

37
 9 The areas are aligned.

Areas are aligned.

■ When there are areas of different sizes, the alignment varies depending on the selected
base area. Click on the area to be the base while pressing [CTRL].

Base Base

Base

38
3.3.3 Area Positioning

Areas can be positioned in the left-hand side, right-hand side, center or top, or bottom side. For
example, the following procrdures are used to position the three frames in the left-hand side.

Select picture frames.

1 Select picture frames (Ex: three picture frames).
While pressing the [Shift] key, click the frames
one by one.

Select [Layout] - [Left].

2 Select [Layout] - [Left].

39
 3 The three picture frames are positioned in the
left-hand side.

Three picture frames are positioned

in the left-hand side.

40
 3.4 Editing of Existing Variety Templates

Create an original template using the templates provided with the Variety Print Software .

1 Set the Variety Template CD in the CD drive.

C5R015

Select [File] - [open].

2 Select [File] - [Open].

3 Click the [...] button at the right-hand side of the

[Composition Info File] box.

Click.

41
 Select template.
4 In the “Open” window, select a desired template
in the CD drive (default is N drive)and then click
the [Open] button.

Click. Some templates cannot be edited (thumbnail of these

can be displayed) and the error message appears. In
this case, select another template that can be edited.

Click the template.

5 Check the template, and then click the [OK]

button.

Click.

6 Normally, select [Protect as background].

Select.

42
 7 The selected template is displayed as the whole
base.

Add the title areas.

8 Edit the template. (Ex: Add the [TITLE] area.)

9 Upon completion of editing, select [File] - [Save

As] to save it using the different file name.

43
 10 Remove the Variety Template CD from the CD
drive.

C5R017

11 After saving, register the template in the

FRONTIER 500, and then use it in the same
way as the newly created template.
(See “2.3 Registration into FRONTIER 500”.)

44
 3.5 Reference Materials for Operations

3.5.1 Print Size/Base Size/Pixel Reference Table

The following is the reference table for the print name, print size, base size and number of pixels.
You can refer it when creating the image that to be used as image area, or when taking a picture by
the digital camera.

Name Print Size (mm/inch) Base Size (pixels) number of pixels

89C (3R) 89x127/3.5x5 1076x1524 1.64M pixels
102C (4R) 102x152/4x6 1228x1818 2.23M pixels
5R 127x178/5x7 1536x2138 3.28M pixels
8 x 10 (8R) 203x254/8x10 2434x3036 7.39M pixels

The base sizes are shown with pixels, that have a margin larger than the print sizes shown below.

Print Size Margin

89C/102C/5R 2mm
8x10/10x12 3mm

45
3.5.2 Types of Sample Templates

Several sample templates are provided with the Template Editing Tool. You can create the original
template by editing them freely. The following five types of sample templates are provided.

q Album Sample (A4) w 4 x 4 Index (89C(3R))

e 7 x 6 Index (A4) r Memory Copy with one title box (5R)

t Memory Copy with one title box

(89C(3R))

They are stored in the following five folders [C:\TplEdit\_Library\Template].

q album-sample-a4
w fitindex4x4-sample-l
e index7x6-sample-a4
r memory-1ebd-sample-5r
t memory-1ebd-sample-3r

46
3.5.3 Using the Sample Templates

Select [File] - [Open].

1 Select [File] - [Open].

2 The “Open Composition Info File” screen

appears.

Add a check.
3 Add a check [✔] to [Use Sample Library] box,
and then click the [...] button in the right-hand
side of the [Composition Info File] entry box.

Click.

47
 4 In the “Open” screen, the five sample file folders
appear.

Select a folder.

5 Select a folder including the desired sample

template, and then click the [Open] button.

Click.

Select the template.

6 Select the desired composition info file

(extension [tpl]), and then click the [Open]
button.

Click.

7 In the “Open Composition Info File”, click the

[OK] button.

You can check the thumbnail of the selected template in

the “Open Composition Info File” screen.

Click.

48
 In case of selecting “index“ or “memory“ template, the
following screen appeaers.
Normally, select [Protect as background].

Click the sample template.

Select.

8 The selected sample template appears in the

main screen.

Edit the template.

9 Edit the template.

In the example shown at the left, the picture areas are

moved and a title area is added.

49
 Select [File] - [Save As].

10 In the menu bar, select [File] - [Save As].

Select the items properly.

11 In the “Save/Save As” screen, select the

following items, and then click the [OK] button.

• Template Group
• Template Name
• Template No.

The folders [Template], [Template Group] and [Template

No.] are created, and template information is stored in

Click. them.

12 In the confirmation message, click the [OK]

button.

If a folder with the same name exists, this message

does not appear.
Click.

13 In the “Check Thumbnail Update” screen, click

the [Update] button.

Click.

50
 3.6 Using the HELP Screen

The Template Editing Tool provides the on-line HELP Screen. When an operation is unknown during
opening the screen, you can refer to it by simply clicking.

1 Select [Help] - [Help] in the menu bar.

Select [Help] - [Help].

2 In the “HELP” screen, click the desired item

(underlined).

Click the desired item (underlined).

3 Use the scroll bars at the right-hand side and at

the bottom, to scroll the pages.

HELP contents Scroll bars

51
 Click.

4 To close the screen, click the [X] button in the

upper right-hand corner.

52
 4 Customizing

4.1 File

Set up the operations for creating a new template, opening the existing file, or saving it.

Select [Customize] - [File]. 1 Select [Customize] - [File].

2 Make the following settings.

53
 No. Item Description
1 Default Resolution Resolution value that is used when opening the template whose resolution is not
defined yet.
It is set as 300dpi, so to prevent print failure, please do not change it.
2 Unit for base size Unit that is used in the [Header/Base Edit] window. It will be used for size or margin
settings.
3 Eclipse Adjustment Settings for enlargement to allow for eclipsing.
When [The base size will be enlarged during loading or creating.] is checked, the area
for eclipsing will be added to the editing area during loading or creating the template.
This function is only available when using 300dpi of resolution.
When [The size of the title area around the base will be adjusted during loading.] is
checked, the title area is adjusted so as not to come too close to the periphery. The
default of peripheral area is 16 pixels from a edge of a base.
4 Overlapping Order When [When saving etc., priority is given to the frame number.] is checked, in order to
of Picture Area reduce the number of scanning times in Frontier as much as possible, a template of
Changed Automati- the same frame number is collected and the order of overlapping is changed automati-
cally cally.
But, when there is an overlap of picture areas, the same frame number is collected
only when the order of overlapping is continued.
5 Thumbnail Update [Check Thumbnail Update] controls the confirmation message about overwriting of the
Check existing thumbnails (Check Thumbnail Update window).
[Update the current template without check.] works with [Update without check]. Once
the latter is checked [✔] when saving, the [Thumbnail Check] window will no longer be
displayed from the next time. If the check [✔] is removed, the window will be displayed.
When you edit another template, this switch is automatically turned OFF.
When [Update all templates without check.] is checked [✔], the [Thumbnail Check] win-
dow is not displayed and the thumbnail is certain to be updated.
6 Default Template Folder name that is displayed in the [Destination Parent Folder] in the [Save/Save As...]
Parent Folder window when you save a new template.
Under this folder, the template composition file [Template\Template Group\Template
No.\Template No..tpl] will be stored.
When registering to the FRONTIER 500, save to the FD and CD all the template data
which is saved to the folder, operates registration work.

54
 4.2 Editing

Set up the operations for editing templates.

Select [Customize] - [Edit].

1 Select [Customize] - [Edit].

2 Make the following settings.

55
 No. Item Description
1 Unit for position/size Initial unit values to be used in unit combo boxes seen in the several windows.
values
2 Area moving button Area moving value when you click one of the buttons (Up/Down/Left/Right/Front/Back)
step amount in the tool bar. You can select from 1 to 2000.
3 Monitor Size Adjust- Correction device for adjusting the monitor display magnification.
ment Normally, it must be turned [Auto-adjust] to ON. Most PCs display correct size image
with this ON setting.
If the displayed data size and actual size are mismatched when setting the magnifica-
tion to 100%, we recommend you to turn [Auto-adjust] to OFF, and measure the hori-
zontal size of the displaying area with a ruler, and then set this value in millimeters or
inches (pixels are not used).
4 Font Size List Font size that to be used in the combo box in the Title Area Properties. You can set it at
a value from 4.0 to 72.0.
When the [OK] button is clicked, the sizes are automatically sorted in ascending order.
The next time you open the Customize window, it will be displayed in this order.

56
 4.3 Tool

Set up the [Tool] menu items.

Select [Customize] - [Tool].

1 Select [Customize] - [Tool].

2 Make the following settings.

1 2

No. Item Description

1 Name Sets up any name that appears in the [Tool] menu.
2 Path Sets up the path name for the editing program. Enter the path name directly in the
entry box or click the [...] button in the right-hand of the path entry box, and then select
the path.
If the first entry is blank when this screen is closed or when the Template Editing Tool is
started up for the first time, the Windows default editor is automatically selected, and
the [Text editor] is registered as the application name.

57
 4.4 Test Image

Set up the path name to the folder in which the test images are stored.

Select [Customize] - [Test Image].

1 Select [Customize] - [Test Image].

2 Make the following settings.

Set up the path name for the test image that to be displayed in the [PICT] area when you select
[View] - [Image Display].

Enter the path name directly in the entry box or click the [...] button in the right-hand corner of the
entry box, and then select the path.

If the [OK] button is clicked, the system checks if the file can be accessed or not.
The registered images from upper to lower correspond to each number of the picture areas. If there
are more picture areas than the images, recycling is done from the first image (the upper one)
again.

This image is not added to the template composition information file, but it is only pasted for test display.

58
 4.5 Test Text

1 Select [Customize] - [Test Text].

Select [Customize] - [Test Text].

2 Make the following settings.

Set up the path name for the test text that to be displayed in the [TITLE] area when you select [View]
- [Test View].

If the text includes the [\], it begins on a new line after the [\]. The registered texts from upper to
lower correspond to each number of the title areas. If there are more title areas than texts, recycling
is done from the first text (the upper one) again.

This text is not added to the template composition information file, but it is only pasted for test display.

59
 5 Troubleshooting

5.1 Messages and Countermeasures

No. Error Message Cause(s) Action(s)

I-TE0001 TE0001 Template is stored in a If you change the template group or A new template will be saved in a
specific new folder. template No. to an unknown one, it specific folder. Use this folder.
will be stored under a specific path.
E-TE0002 TE0002 Character entry for An incorrect character is used for Make the template group name
template group is(are) incorrect. template group name or too long a less than 30 characters to be
Use 1 to 30 character(s) that is name is used. available as the folder name.
proper for Windows folder name.
E-TE0003 TE0003 Select the correct The template group name is not Select the correct template group
template group. selected. from the list.
E-TE0004 TE0004 Template No. is incorrect. An incorrect character is used for Make the template group number
Use 1 to 30 character(s) that template number or too long a less than 20 characters to be
is(are) proper for Windows folder number is used. available as folder name.
name.
E-TE0005 TE0005 Creating of thumbnail Creating of thumbnail (reduced Solve the problem, and then try
failed. image that is used for image list) saving again, or reinstall the
failed. The saving device may be application software.
abnormal.
E-TE0006 TE0006 Generating of image Generating of image failed. It may Solve the problem, and then try
failed. be caused by an image saving again, or reinstall the
abnormality. application software.
E-TE0007 TE0007 Memory space is Memory space is insufficient. Shut down other applications.
insufficient.
E-TE0008 TE0008 Memory space is Memory space is insufficient. Shut down other applications.
insufficient. (A specified free space
is allocated for other application.)
E-TE0009 TE0009 This is a unsupported Registering of the image file with Select any of the supported image
image format. unsupported format was tried. formats.
E-TE0021 TE0021 Starting of application Installation was abnormally Reinstall the application software.
failed. To solve the problem, cancelled.
reinstall the template editor.
E-TE0023 TE0023 Customize file Setting of the customize file Reinstall the application software.
“FolderPref.ini” is incorrect. “FolderPref.ini” is incorrect.
E-TE0024 TE0024 Processing will be Setting of the customize file Reinstall the application software.
stopped, because customize file “FolderPref.ini” is incorrect.
“FolderPref.ini” is incorrect.
E-TE0025 TE0025 Customize file(template Setting of the customize file Reinstall the application software.
group definition file) is incorrect. “TemplateGroup.ini” is incorrect.
E-TE0026 TE0026 Template group name is An incorrect character is used for Make the template group name
incorrect. Use 1 to 30 character(s) template group name or too a long less than 30 characters to be
that is proper for Windows folder name is used. available as the folder name.
name.
E-TE0027 TE0027 Customize file (paper size Setting of the customize file Reinstall the application software.
definition file) is incorrect. “PaperSize.ini” is incorrect.
E-TE0028 TE0028 “Pixel” is used for unit in Setting of the customize file Reinstall the application software.
the paper size definition file, but “PaperSize.ini” is incorrect.
resolution is not specified.
E-TE0029 TE0029 Customize file (aspect Setting of the customize file Reinstall the application software.
ratio definition file) is incorrect. “Aspect.ini” is incorrect.
E-TE0033 TE0033 Setting of test data is Test image data cannot be opened. Correct the setting in the
incorrect. Customize/Test Image Setting.
E-TE0034 TE0034 Loading of character FatTextLut.txt cannot be loaded. Reinstall the application software.
processing LUT file failed.

60
 No. Error Message Cause(s) Action(s)
E-TE0101 TE0101 Resolution is out of range. Unsupported resolution is used for Such template cannot be edited
template. with the editor.
E-TE0102 Other than TE0102 Unsupported format is used for Such template cannot be edited
TEMPLATE_TYPE 0 and 3 is not template. with the editor.
supported.
E-TE0103 TE0103 Pair template is not Unsupported format is used for Such template cannot be edited
supported. template. with the editor.
E-TE0104 TE0104 Other than Unsupported format is used for Such template cannot be edited
ORDER_TYPE 0 is not supported. template. with the editor.
E-TE0105 TE0105 Title pair process is not Unsupported format is used for Such template cannot be edited
supported. template. with the editor.
E-TE0106 TE0106 Calendar is not Unsupported format is used for Such template cannot be edited
supported. template. with the editor.
E-TE0107 TE0107 Overlay is not supported. Unsupported format is used for Such template cannot be edited
template. with the editor.
E-TE0108 TE0108 Template size is incorrect. Unsupported format is used for Such template cannot be edited
template. with the editor.
E-TE0121 TE0121 Couldn’t open file. The template file cannot be Such template cannot be edited
opened. with the editor.
E-TE0122 TE0122 Couldn’t read file The file cannot be loaded. Such template cannot be edited
correctly. with the editor.
W-TE0123 TE0123 Notice: Couldn’t read file The file cannot be loaded. Reading Correct problem.
correctly. will be continued skipping this file.
E-TE0124 TE0124 Composition information Incorrect format is used for Such template cannot be edited
file is incorrect. template. with the editor.
E-TE0125 TE0125 Incorrect parameter is Such template cannot be edited
—
used. with the editor.
E-TE0126 TE0126 Incorrect key is used. Incorrect format is used for Such template cannot be edited
template. with the editor.
E-TE0127 TE0127 Incorrect area No. is used. Incorrect format is used for Such template cannot be edited
template. with the editor.
E-TE0128 TE0128 Couldn’t find the following Essential item is not written. Such template cannot be edited
information. with the editor.
W-TE0129 TE0129 Notice: Couldn’t find the Essential item is not written. Correct problem.
following information. Reading will be continued skipping
the error.
E-TE0130 TE0130 Couldn’t find the The coordinate for image area is Such template cannot be edited
coordinate for image area. not written. with the editor.
E-TE0131 TE0131 Incorrect vertical/ Vertical/horizontal value for area is Such template cannot be edited
horizontal value is used. incorrect. with the editor.
E-TE0132 TE0132 Couldn’t find file name. The image file name in the image Such template cannot be edited
area is not given. with the editor.
E-TE0133 TE0133 Incorrect file type referred. The image file with unsupported Such template cannot be edited
format is referred. with the editor.
E-TE0134 TE0134 Incorrect entry. Other template format error. Such template cannot be edited
with the editor.
E-TE0135 TE0135 No picture area found. A picture area is not created. Such template cannot be edited
with the editor.
E-TE0137 TE0137 IMAGE_ORDER in image Image area “IMAGE_ORDER” is Such template cannot be edited
area is incorrect (0). incorrect. with the editor.
E-TE0138 TE0138 Font height exceeds the Too small font size is used in the Such template cannot be edited
minimum value. text area. with the editor.
E-TE0139 TE0139 Font height exceeds the Too large font size is used in the Such template cannot be edited
maximum value. text area. with the editor.

61
 No. Error Message Cause(s) Action(s)
E-TE0141 TE0141 An error occurred when Internal error. Reinstall the application software.
calculating the base editing size.
E-TE0142 TE0142 An error occurred when Internal error. Reinstall the application software.
calculating the base editing size.
E-TE0143 TE0143 An error occurred when Internal error. Reinstall the application software.
calculating the base editing size.
E-TE0144 TE0144 Couldn’t find the template A template group name is not Such template cannot be edited
group name. given. with the editor.
W-TE0145 TE0145 Notice: Area exceeds the Area exceeds the base limit, so it is Make editing while checking the
base limit. Moving or resizing is adjusted. area around the base.
done so it to be within the limit.
W-TE0146 TE0146 Notice: A title area is The title area is located around the Make editing while checking the
located around the base. The area base, so it is adjusted. area around the base.
near the edge is cropped.
E-TE0147 TE0147 Creating of working folder Creating of working folder failed. Reinstall the application software.
failed. Check the folder attributes Incorrect folder name may be used
or path name. or same folder name may already
exist.
E-TE0201 TE0201 Couldn’t open the save Saving in the working folder failed. Reinstall the application software.
file. Incorrect folder may be created.
E-TE0203 TE0203 No reference file found in Couldn’t access the reference Reinstall the application software.
the working folder. folder. Settings may be incorrect.
E-TE0204 TE0204 Couldn’t save because The file to which the template data Such template cannot be edited
the editing data is incorrect. refers may be corrupted. with the editor.
E-TE0205 TE0205 Couldn’t read image file The file to which the template data Such template cannot be edited
correctly. refers may be corrupted. with the editor.
E-TE0206 TE0206 The following file(s) is(are) There is a read-only file with the Delete the file(s) in the folder, and
read-only. same name in the destination save it (them) again.
folder.
E-TE0207 TE0207 Copying of file failed. Copying of files failed during Such template cannot be edited
saving. The file to which the with the editor.
template data refers may be
corrupted.
E-TE0301 TE0301 Couldn’t edit the template Editing of template stored in the This template cannot be edited
under this folder. working folder is tried. with the editor.
Move it to other folder and open it
again.
E-TE0302 TE0302 Incorrect destination Incorrect destination folder for Select the correct template group
folder template. and template No.
I-TE0305 TE0305 Unknown template group Unregistered template group is Do any of the following actions.
name is used. Register? [Yes] to selected. Register the group name. Select
register it. [No] to reselect from any of the existing groups. Cancel
the existing groups. [Cancel] to the operation.
cancel loading. Template Group
Name:
E-TE0307 TE0307 Image data and mask Unsupported image file is included. Such template cannot be edited
data have an unsupported format. with the editor.
W-TE0308 W-TE0308 In the image area or An image larger than the base is Reduce the image size or create a
the background,there is the image used for image area or background. new image again to fit the base.
whose size is larger than the base
editing size.This template is saved
and used as it is, it may be unable
to use normally in Frontier.We
recommend you to make the size
of the image smaller than the base
editing size.Save it. OK?

62
 No. Error Message Cause(s) Action(s)
E-TE0321 TE0321 Exceeds the available Too many areas are displayed. Delete the unnecessary areas.
number of areas. No more area
created.
E-TE0322 TE0322 Alignment: Specified Selected areas exceed the Increase the horizontal and
number is small. specified number of areas for vertical values.
alignment.
E-TE0323 TE0323 Put the reference areas in A reference area is incorrectly Move the reference areas to
the upper left and lower right sides. located. proper upper left-hand side
position and to lower right-hand
side position in the base.
E-TE0324 TE0324 Select area. No area is selected. Select the area.
E-TE0325 TE0325 An error occurred during Internal error. Reinstall the application.
editing.
E-TE0326 TE0326 Space is insufficient. Internal error. Reinstall the application.
E-TE0327 TE0327 Overlay order cannot be More than two areas are required, Check the causes, and try again.
changed. or they already exist in the highest
or lowest place.
E-TE0328 TE0328 Area cannot be moved. Area cannot be moved outside the Check the causes, and try again.
base.
E-TE0329 TE0329 Incorrect position or scale. The area size exceeds the base Change the area size or move the
size. area positions to be within the
base.
E-TE0330 TE0330 Incorrect destination Incorrect template folder. Correct the template group and
folder. template No.
E-TE0331 TE0331 PICTURE_ORDER is Incorrect frame number. Change the frame number to the
incorrect. correct one between 1 and 64.
E-TE0361 TE0361 The base size (with an Incorrect base size is selected. Select the correct value.
area for eclipse) exceeds the
minimum or maximum value.
E-TE0362 TE0362 Margin value is negative, Incorrect base size is selected. Select the correct value.
or it is larger than the half of the
base size.
E-TE0364 TE0364 Free size cannot be Other sizes than the ones listed are Select from the list.
selected. Select the desired size not defined in the “PaperSize.ini” Reinstall the application software.
from the list. file.
E-TE0381 TE0381 To set the gradation, Same color is selected for the Select each different color for
select different two colors. gradation starting and ending color. gradation starting and ending.
E-TE0382 TE0382 Creating of gradation Internal error. Reinstall the application software.
background color failed.
E-TE0383 TE0383 Exceeds the limit number Total of image areas and Delete the image areas.
of image areas. Gradation cannot backgrounds exceeds the upper
be created. Gradation image is limit (64).
one of the image areas.
E-TE0401 TE0401 This group name is Adding of the template group Add the group with a different
already registered. already registered was tried. name.
E-TE0402 TE0402 No group is registered. No template group is registered. Define one group at least.
Register at least one group.
E-TE0421 TE0421 Incorrect template name The template name is blank or it Set up the template name using up
is used. Reenter the correct one exceeds 30 characters. to 30 characters.
with 1 to 30 character(s).
E-TE0423 TE0423 The same file name as The folder with the same name Change the parent folder, group or
specified folder exists. ready exists. template number and do saving.

63
 No. Error Message Cause(s) Action(s)
E-TE0424 TE0424 Couldn’t access to the Cannot access the drive or media If using the removable media, set it
specified drive media. where you want to save the data. in the drive. Change the parent
folder, group or template number
and do saving.
E-TE0441 TE0441 Incorrect number Too many number of areas or 0 is Set the copying number between 1
specified. Specify a number specified. to 100.
between 1 and 100.
E-TE0442 TE0442 Horizontal distance value Too large or too small value is Set the distance between -10000
is incorrect. Set from -10000 to specified for horizontal direction. to 10000 (pixels).
10000 (pixel).
E-TE0443 TE0443 Vertical distance value is Too large or too small value is Set the distance between -10000
incorrect. Set from -10000 to specified for vertical direction. to 10000 (pixels).
10000 (pixel).
E-TE0444 TE0444 Too many areas. It can be Too much copying area. Select the numeric value so that
no more created. the areas are within 64.
E-TE0445 TE0445 Distance value is Other than numeric value is used Enter the numeric value.
incorrect. Enter the correct for distance.
numeral(s).
E-TE0801 TE0801 The folder name for Cannot access the sample Check the sample library folder if it
sample library may be incorrect. template library folder. exists or if it is read-only.
Cannot access to the folder. Reinstall the application software.
E-TE0802 TE0802 The folder name for image Cannot access the image library Check the image library folder if it
library may be incorrect. Cannot folder. exists or if it is read-only.
access to the folder. Reinstall the application software.
E-TE0803 TE0803 The folder name for mask Cannot access the mask image Check the mask image folder if it
image library may be incorrect. library folder. exists or if it is read-only.
Cannot access to the folder. Reinstall the application software.
E-TE0804 TE0804 The default parent folder Cannot access the default parent Check the default parent folder if it
name may be incorrect. Cannot folder. exists or if it is read-only.
access to the folder. Reinstall the application software.
E-TE0805 TE0805 The working folder name Cannot access the working folder. Check the working folder if it exists
may be incorrect. Cannot access or if it is read-only.
to the folder. Reinstall the application software.
E-TE0806 TE0806 The working folder name Incorrect working folder name. Check the setting of the working
must end with [work] such as folder.
D:\Edit\forWork Reinstall the application software.
E-TE0807 TE0807 Cannot specify under the The paths for template, sample Set up the path to the folder other
working folder. template library and image library than the working folder.
and mask library are under the
working folder. Because the
contents of the working folder are
periodically deleted, they cannot be
created under the working folder.
E-TE0808 TE0808 Set up the resolution Too high or too low resolution is set Set up the resolution between 30
between 30 and 3000 dpi. up. to 30000 dpi.
E-TE0821 TE0821 Set up the font size Too large or too small font size is Set the font size between 4.0 to
between 4.0 and 72.0. selected. 72.0.
E-TE0822 TE0822 Set up the button step Too large or too small area moving Set up the area moving amount
amount between 1 and 2000 amount is selected. between 1 to 2000 (pixel).
(pixel).
E-TE0823 TE0823 Set up the horizontal size The monitor displaying size is Set up the monitor displaying area
of the monitor displaying area with specified with pixel. using millimeter sor inches.
millimeter or inch.
E-TE0861 TE0861 Set the name and path Incorrect name or incorrect path for Set up the name and path.
correctly. tool is used.

64
 No. Error Message Cause(s) Action(s)
E-TE0881 TE0881 Set up at least one test The test image is not set up. Set up at least one test image.
image file.
E-TE0882 TE0882 Couldn’t load a test image The test image is not loaded. Correct the file path to the test
file. image.
E-TE0883 TE0883 Set up at least one test The test text is not set up. Set up at least one test text.
text.
E-TE0901 TE0901 Calling of HELP failed. The HELP contents cannot be Check if the browser is properly
displayed. operated. (if the HTML file can be
opened.)

65
 5.2 Uninstallation

5.2.1 Uninstallation Using Installer CD

Delete the Template Editing Tool program from the DIC II or other personal computer using the
installer CD.Before deleting it from the DIC II, quit the DIC II Basic Software [S2] by using “Post-
operational checks.”

1 Set the Template Editing Tool installer CD in the

CD drive.

2 On the Desktop, select [Start] - [Run].

Select [Start]-[Run].

Select [Setup].

3 In the “Run” screen, click the [Browse] button to

open the [Template Editing Tool] folder in the
CD drive, and then select [Setup]. Then, click
the [Open] button.

Click the [Open] button.

Check that [E:\Template Editing Tool\Setup.exe]

4
is displayed.
In the “Run” screen, check that [E:\Template
Editing Tool\Setup.exe] is displayed in the
[Open] box, and then click the [OK] button.

The drive letter (ex: E:) varies depending on your PC.

Click.

66
 5 “Preparing uninstaller...” message appears.

6 After a few seconds, the installer main screen

appears.

7 In the installer main screen, click the [Uninstall]

button, and then click the [OK] button.

If the [Cancel] button is clicked in the installer main

screen, the confirmation screen appears. To cancel the
uninstallation, click the [OK] button.

Click the [Uninstall] button. Click.

To cancel the uninstallation,

click the [OK] button.

67
 8 The uninstallation confirmation screen appears.
Click the [OK] button.

Click the [OK] button.

9 The program is uninstalled.

10 The uninstallation completion screen appears.

Remove the Template Editing Tool installer CD
from the CD drive.
Click the [OK] button to restart the system.

Click the [OK] button. To restart the system later, click the [Reboot Later]
button.

Click the [Reboot Later] button.

68
5.2.2 Uninstallation with Desktop Screen

Delete the Template Editing Tool program from the DIC II or other personal computer using the
[Start] menu in the Windows Desktop screen.Before deleting it from the DIC II, quit the DIC II Basic
Software [S2] by using “Post-operational checks.”

1 In the Desktop screen, select [Start] -

[Programs] - [FDi] - [Template Editing Tool] -
[Uninstall].

Select [Start] - [Programs] - [FDi] -

[Template Editing Tool] - [Uninstall].

2 “Preparing uninstaller...” message appears.

3 In the confirmation message screen, click the

[OK] button.

Click the [OK] button.

69
 4 The program is uninstalled.

5 The uninstallation completion screen appears.

Click the [OK] button to restart the system.

Click the [OK] button.

To restart the system later, click the [Reboot Later]
button.

Click the [Reboot Later] button.

70
FAX : 81-3-5484-0454

Questionnaire concerning This Manual

Fujifilm’s Photo Imaging Technical Service Division would be most grateful if you would make copies of this form, then complete
and send them to us by FAX.
Your opinions will contribute greatly to an accurate assessment of the overall quality of each manual.
All questions can be answered by ticking [✓] the appropriate box(es), but in addition to these answers, please provide us with your
written comments in the lined spaces following each block of questions.

Title : FRONTIER 500

VARIETY PRINT SOFTWARE TEMPLATE EDITING TOOL
Manual Title and Reference Number INSTRUCTION MANUAL
Reference Number : PP3-B1174E

Name :

Your Name and Company

Company :

E-mail Address :

Your E-mail Address and FAX Number

FAX Number :

Question 1 • How would you rate this manual overall?

(1) Very easy to use and understand (2) Fairly easy to use and understand
(3) Slightly difficult to use
(4) Very difficult to use and understand
and understand
• Please provide us with your reasons and comments.

Question 2 • Have you found any technical errors, errors in spelling, or missing words in this manual?
Yes No
• If you have ticked (Yes), please let us know what these errors and missing words are.

Question 3 • How would you rate the writing (language, choice of words/phrases, etc.) and the illustrations/
diagrams, etc.?
(1) Clear and easy to follow (2) Should be simplified
(3) Difficult to follow
(1)’ [Illustrations, etc.] Of adequate size
(2)’ [Illustrations, etc.] Too small
(3)’ [Illustrations, etc.] Difficult to follow
• If you have ticked (2), (3) or (3)’, please give us your reasons.

Additional
Comments/
Requests
concerning
This Manual

Please return this questionnaire to : FAX No. : Tokyo 81-3-5484-0454

FUJI PHOTO FILM CO., LTD.
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.

<FUJIFILM ABROAD>
in North America FUJI PHOTO FILM U.S.A., INC.
200 Summit Lake Drive, Valhalla, New York 10595-1356, U.S.A.
FUJI PHOTO FILM CANADA INC.
600 Suffolk Court, Mississauga, Ontario, L5R 4G4, Canada
FUJI PHOTO FILM HAWAII, INC.
94-468 Akoki Street, Waipahu, Hawaii 96797, U.S.A.
in Europe FUJI PHOTO FILM (EUROPE) G.m.b.H.
Heesenstrasse 31, 40549 Dusseldorf, Germany
FUJI PHOTO FILM (U.K.) LTD.
Fuji Film House, 125 Finchley Road, Swiss Cottage, London NW3 6HY, U.K.
FUJIFILM ESPAÑA, S.A.
Aragon, 180, 08011-Barcelona, Spain
FUJIFILM FRANCE SAS
Parc d' Activites du Pas-du-Lac-2, Avenue Franklin, 78186 St. Quentin en Yvelines Cedex, France
in Central America FUJI PHOTO FILM CO., LTD., MEXICO OFFICE
Av. Ejercito Nacional 351, 5˚ piso, Col. Granada, 11520 Mexico D.F., Mexico
in South America FUJI PHOTO FILM DO BRASIL LTDA.
Avenida Vereador Jose Diniz, No. 3400, Campo Belo, São Paulo CEP 04604-901,
Cx. Postal 3656, Brazil
in Asia FUJI PHOTO FILM CO., LTD., HONG KONG OFFICE
Room 2208, Tower 6, The Gateway Harbour City, 9 Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong
FUJIFILM REGIONAL SERVICES (SINGAPORE) PTE. LTD.
10 New Industrial Road, Fujifilm Building, Singapore 536201
FUJI PHOTO FILM (THAILAND) LTD.
S.P. Building, 8th Floor, 388 Phaholyothin Road, Bangkok 10400, Thailand
FUJI PHOTO FILM (MALAYSIA) SDN. BHD.
Letter Box 3, 3rd Floor Office Block 1, Crystal Plaza Lot 4, Jalan 51A/223
46100 Petaling Jaya Selangor Darul Ehsan Malaysia
FUJI PHOTO FILM CO., LTD., TAIPEI OFFICE
Rm. 601, Hung Chong Bldg., No. 38, Sec. 6, Min Chuan E. Road, Taipei 11453, Taiwan
FUJI PHOTO FILM CO., LTD., SEOUL OFFICE
505-19, Kasan-Dong, Kumchon-Gu, Seoul, Korea 152-020
FUJI PHOTO FILM CO., LTD., BEIJING REPRESENTATIVE OFFICE
Beijing Fortune Bldg. No. 817, 5, Dong Sanhuan Bei-lu, Chaoyang District, Beijing, China 100004
FUJI PHOTO FILM CO., LTD., HO CHI MINH OFFICE
7th Floor Sun Wah Tower, 115 Nguyen Hue Street, Dist. 01, Ho Chi Minh City, Vietnam
FUJI PHOTO FILM CO., LTD., NEW DELHI OFFICE
Le Meridien Commercial Tower 8F, Janpath, New Delhi 110001, India
FUJI PHOTO FILM CO., LTD., MANILA OFFICE
c/o YKL Development & Trading Corporation, 24 Sto. Domingo St., Quezon City, Metro Manila, Philippines
in Oceania FUJIFILM AUSTRALIA PTY LTD
c/o Hanimex Pty. Limited, 114 Old Pittwater Road, Brookvale, N.S.W. 2100, Australia
FUJIFILM NZ LIMITED
Cnr Willam Pickering Drive and Bush Road, ALBANY, New Zealand
in the Middle East FUJI PHOTO FILM CO., LTD., DUBAI OFFICE
No. 14, L.O.B. No. 4, P.O.Box 17212, Jebel Ali, Dubai, U.A.E.
in South Africa Fuji Photo Film Co., Ltd., Johannesburg Office
9th Floor, Sandton City Office Towers, Cnr Rivonia Road & 5th Street, Sandton 2196, South Africa

Printed on Recycled Paper

Ref.No.PP3-B1174E ESD-06.2-FP Printed in Japan