TJM/2003770-R9- Finalized FOR Delivered Techno Commercial Bid July 27th, 2023

Kind Attn. Mr. Viraj Pal

Assistant Manager - Procurement
Apollo International Limited
Apollo Towers, Plot No. 20,
Sector 44, Gurgaon - 122002
Haryana, India
Mo No: +91-9893203028
E-mail ID: [email protected]

PROJECT : BR-9 EXPANSION PROJECT, BARAUNI, BIHAR, INDIA

CLIENT : INDIAN OIL CORPORATION LIMITED (IOCL)

PMC : TOYO ENGINEERING INDIA PRIVATE LIMITED.

CONTRACTOR : APOLLO INTERNATIONAL LIMITED

ITEM : TANK JET MIXERS

DOCUMNET NO : EPCC11-AIL-301-STA-MRP-000-0010

Dear Sir,

This has reference to our yesterday’s detailed Joint discussions over TEAMS with your good self and your
Mr. Bhsakar Ji, Mr. Aman Ji and Mr. Divyansh Ji in line with above stated subject matter requirement.
Based on same, we are submitting herewith our Finalized Techno Commercial Proposal of Tank Jet Mixer
for your ready reference and kind consideration.

 We have considered working Volume of Tank as per HHLL Height provided by you in your Tanks
Drawings for all Tag Nos. Tanks and accordingly we are submitting herewith our revised Techno-
Commercial Bid for your reference and consideration. Also note Homogenous mixing confirmed
by us is upto HHLL only
 We will match Header/O-Ring Sizes as per mentioned in your Tanks Drawings.

We, Chem Process Systems Pvt. Ltd., are certificate holder for ASME U, National Board R & NB. Chem
Process has for many years held accreditation to ISO 9001:2015 this along with accreditation to ASME U
firmly places Chem Process at the top of the Quality ladder.

Traditionally, but certainly not exclusively, Chem Process concentrates on the oil refinery, petrochemical,
power generation, pharmaceutical, chemical, distilling, brewing and food processing industries, wherever

Page 1 of 19
these are located throughout India and also in the world. Consequent to our good manufacturing
practices and quality assurance schemes, our workshop and offices are ISO certified by DNV.

We are sure that our proposal will be in line with your requirement. In case of any clarifications required,
please inform us.

Thanking you,

FOR, CHEM Process Systems Pvt. Ltd.

Meghnad Desai (Mob: +91-9714006204)

Asst. Manager - Marketing and Proposals, Vacuum Division

Brief Profile

Introduction

Chem Process Systems Pvt. Ltd., Ahmedabad, Gujarat State, India, is one of the leading suppliers of
Steam Jet Vacuum Equipment. The company designs, manufactures, tests and commissions a wide
variety of systems such as Steam Jet Ejectors, Thermo compressor, Surface Condensers, Steam Jet
Refrigeration Systems, Multiple Effect Evaporation Plants, Crystallizers, Zero Effluent Discharge Systems,
Steam Jet Heaters & Mixers, Desuper-heaters and many more.

Traditionally, but certainly not exclusively, Chem Process concentrates on the oil refinery, petrochemical,
power generation, pharmaceutical, chemical, distilling, brewing and food processing industries, wherever
these are located throughout India and also in the world. Consequent to our good manufacturing
practices and quality assurance schemes, our workshop and offices are ISO certified by DNV.

Vacuum Specialists

The Chem Process engineering team has extensive experience of more than 20 years in this highly
specialized area and they have closely worked on projects with the staff of international companies like
Lurgi GmBh, Uhde, Kvaerner Powergas (Davy Powergas), John Brown, Humphreys & Glasgow, Toyo
Engineering, Brown Boveri, Dupont, etc. In addition to a comprehensive range of standard equipment,
our team is able to apply their experience to respond quickly to provide highly efficient solutions to a
broad base of applications. Our employees have extensive knowledge of the vacuum industry
applications and are able to apply this knowledge to ensure that the correct components are designed to
match the task at hand.

The Design Process

A variety of computerized and manual, thermal and mechanical design techniques are employed in the
design of bespoke installations. Furthermore, Chem Process has access to the state of the art industry

Page 2 of 19
technology and additional computer aided design facilities geared to the heat transfer industry at the
highest possible level.

Page 3 of 19
 TECHNICAL DATASHEET

SYSTEM-1: TANK JET MIXERS (MS TANK - TAG NO: 301-T-303/ 304)
DESIGN DATA:

Sr. No. Particulars Unit Value

1. Application - Homogeneous
mixing
2. Tank Diameter mm 30000
3. Tank Height mm 19300
4. Tank HHLL Height mm 15675

5. Volume as per HHLL Height considered M3 11080

6. Total Tank capacity M3 13600
7. Fluid MS/ Ethanol Blended MS
8. Fluid Density Kg/m3 710-775
9. Viscosity cP 0.3-0.66
10. Operating Temperature (Normal / Max.) Deg C 40/ 50
11. Motive Liquid Pressure at inlet of Jet Mixer Kg/cm2(g) 4.0
12. Design Pressure Kg/cm2(g) 5.2
13. Design Temperature Deg C 65
14. Total Motive Flow Rate M3/hr 360
15. Motive Flow Rate per Mixer M3/hr 45
16. Mixing Time Hr. 1.79
17. No. of Mixer per Tank Nos. 8.0
18. Mixer Connection Size NB 100
19. O- Ring/ Header Size NB 250
Notes:
 Our Mixer will perform satisfactorily subjected to Mixer should be submerged, Driving Flowrate
and Pressure from pump for Mixer should operate at Designed parameters i.e. pressure, flow
rate and Specific Gravity of fluid
 We have not considered cost of appointing Third Party Inspection. Same is to be appointed by
M/s. Apollo International Limited.
 We will provide scanned copy of MTC. In absence of the same we will provide check testing
reports.

Page 4 of 19
  As per Standard Practice and our company policy for executing orders for similar requirement
in Refineries, we are not sharing any type of calculations regarding Mixer Design and Sizing as it
falls under our Proprietary Design Part
 Hydro test for Tank Jet Mixer is not applicable
Material of Construction:

Sr. No. Description MOC

1. Body SS 316
2. Nozzle SS 316
3. Flange SS 316, WNRF, As per ANSI B16.5, 150#

4. Gasket SS 316 Spiral Wound with Graphite Filler

5. Fasteners SA 193 Gr. B8 / SA 194 Gr. 8
*Note: Material of Construction selection is as per your requirement and compatibility suitability. We
do not stand guarantee for selection of MOC/Corrosion

Scope of Supply:

Sr. No. Description Qty.

SYSTEM-1: TANK JET MIXERS (MS TANK - TAG NO: 301-T-303/ 304) 8 Nos. Per Tank

ERECTION AND COMMISSIONING SPARES

1. Gaskets 200%
2. Fasteners (Min 2 Nos. stud and 4 Nuts) 10%
TWO YEAR OPERATIONAL SPARES
3. Gaskets 400%
4. Fasteners (Min 4 Nos. stud and 8 Nuts) 20%

TECHNICAL DATASHEET

SYSTEM-2: TANK JET MIXERS (NAPHTHA TANK: - TAG NO: 301-T-307)

DESIGN DATA:

Sr. No. Particulars Unit Value

1. Application - Homogeneous
mixing
2. Tank Diameter mm 37500
3. Tank Height mm 17700
4. Tank HHLL Height mm 14005
5. Volume as per HHLL Height considered M3 15468

Page 5 of 19
 6. Total Tank capacity M3 19539
7. Fluid Naphtha/ Ethanol
8. Fluid Density Kg/m3 725-790
9. Viscosity cP 0.2-0.6
10. Operating Temperature (Normal / Max.) Deg C 40/ 50
11. Motive Liquid Pressure at inlet of Jet Mixer Kg/cm2(g) 3.9
12. Design Pressure Kg/cm2(g) 4.7
13. Design Temperature Deg C 65
14. Total Motive Flow Rate M3/hr 360
15. Motive Flow Rate per Mixer M3/hr 60
16. Mixing Time Hr. 2.44
17. No. of Mixer per Tank Nos. 6.0
18. Mixer Connection Size NB 150
19. O-Ring/ Header Size NB 250
Notes:
 Our Mixer will perform satisfactorily subjected to Mixer should be submerged, Driving Flowrate
and Pressure from pump for Mixer should operate at Designed parameters i.e. pressure, flow
rate and Specific Gravity of fluid
 We have not considered cost of appointing Third Party Inspection. Same is to be appointed by
M/s. Apollo International Limited.
 We will provide scanned copy of MTC. In absence of the same we will provide check testing
reports.
 As per Standard Practice and our company policy for executing orders for similar requirement
in Refineries, we are not sharing any type of calculations regarding Mixer Design and Sizing as it
falls under our Proprietary Design Part
 Hydro test for Tank Jet Mixer is not applicable

Material of Construction:

Sr. No. Description MOC

1. Body SS 316
2. Nozzle SS 316
3. Flange SS 316, WNRF, As per ANSI B16.5, 150#

4. Gasket SS 316 Spiral Wound with Graphite Filler

5. Fasteners SA 193 Gr. B8 / SA 194 Gr. 8

Page 6 of 19
*Note: Material of Construction selection is as per your requirement and compatibility suitability. We
do not stand guarantee for selection of MOC/Corrosion

Scope of Supply:

Sr. No. Description Qty.

SYSTEM-2: TANK JET MIXERS (NAPHTHA TANK: - TAG NO: 301-T-307) 6 Nos. per tank

ERECTION AND COMMISSIONING SPARES

1. Gaskets 200%
2. Fasteners (Min 2 Nos. stud and 4 Nuts) 10%
TWO YEAR OPERATIONAL SPARES
3. Gaskets 400%
4. Fasteners (Min 4 Nos. stud and 8 Nuts) 20%

TECHNICAL DATASHEET

SYSTEM-3: TANK JET MIXERS (SRN TANK: - TAG NO: 301-T-311/312)

DESIGN DATA:

Sr. No. Particulars Unit Value

1. Application - Homogeneous
mixing
2. Tank Diameter mm 19500
3. Tank Height mm 15800
4. Tank HHLL Height mm 13650
5. Volume as per HHLL Height considered M3 4076
6. Total Tank capacity M3 4716
7. Fluid SRN
8. Fluid Density Kg/m3 720-775
9. Viscosity cP 0.34-0.6
10. Operating Temperature (Normal / Max.) Deg C 50/ 60
11. Motive Liquid Pressure at inlet of Jet Mixer Kg/cm2(g) 10
12. Design Pressure Kg/cm2(g) 13 40/50

13. Design Temperature Deg C 65

14. Total Motive Flow Rate M3/hr 75-104
15. Motive Flow Rate per Mixer M3/hr 75-104
16. Mixing Time Hr. 2.37 / 2.10

Page 7 of 19
 17. No. of Mixer per Tank Nos. 1.0
18. Mixer Connection Size NB 150
19. O-Ring / Header NB Not Required

Notes:
 Our Mixer will perform satisfactorily subjected to Mixer should be submerged, Driving Flowrate
and Pressure from pump for Mixer should operate at Designed parameters i.e. pressure, flow
rate and Specific Gravity of fluid
 We have not considered cost of appointing Third Party Inspection. Same is to be appointed by
M/s. Apollo International Limited.
 We will provide scanned copy of MTC. In absence of the same we will provide check testing
reports.
 As per Standard Practice and our company policy for executing orders for similar requirement
in Refineries, we are not sharing any type of calculations regarding Mixer Design and Sizing as it
falls under our Proprietary Design Part
 Hydro test for Tank Jet Mixer is not applicable

Material of Construction:

Sr. No. Description MOC

1. Body SS 316
2. Nozzle SS 316
3. Flange SS 316, WNRF, As per ANSI B16.5, 150#

4. Gasket SS 316 Spiral Wound with Graphite Filler

5. Fasteners SA 193 Gr. B8 / SA 194 Gr. 8
*Note: Material of Construction selection is as per your requirement and compatibility suitability. We
do not stand guarantee for selection of MOC/Corrosion

Scope of Supply:

Sr. No. Description Qty.

SYSTEM-3: TANK JET MIXERS (SRN TANK - TAG NO: 301-T-311/312) 1 No. Per Tank

ERECTION AND COMMISSIONING SPARES

1. Gaskets 200%
2. Fasteners (Min 2 Nos. stud and 4 Nuts) 10%

Page 8 of 19
TWO YEAR OPERATIONAL SPARES
3. Gaskets 400%
4. Fasteners (Min 4 Nos. stud and 8 Nuts) 20%

TECHNICAL DATASHEET

SYSTEM-4: TANK JET MIXERS (REFORMATE TANK: - TAG NO: 301-T-313)

DESIGN DATA:

Sr. No. Particulars Unit Value

1. Application - Homogeneous
mixing
2. Tank Diameter mm 22800
3. Tank Height mm 13600
4. Tank HHLL Height mm 11505
5. Volume as per HHLL Height considered M3 4697
6. Total Tank capacity M3 5550
7. Fluid Reformate
8. Fluid Density Kg/m3 740
9. Viscosity cP 0.5-0.6
10. Operating Temperature (Normal / Max.) Deg C 50/ 60
11. Motive Liquid Pressure at inlet of Jet Mixer Kg/cm2(g) 10.5
12. Design Pressure Kg/cm2(g) 13.65
13. Design Temperature Deg C 65
14. Total Motive Flow Rate M3/hr 110
15. Motive Flow Rate per Mixer M3/hr 110
16. Mixing Time Hr. 2.32
17. No. of Mixer per Tank Nos. 1.0
18. Mixer Connection Size NB 150
19. O-Ring / Header NB Not Required
Notes:
 Our Mixer will perform satisfactorily subjected to Mixer should be submerged, Driving Flowrate
and Pressure from pump for Mixer should operate at Designed parameters i.e. pressure, flow
rate and Specific Gravity of fluid
 We have not considered cost of appointing Third Party Inspection. Same is to be appointed by
M/s. Apollo International Limited.

Page 9 of 19
  We will provide scanned copy of MTC. In absence of the same we will provide check testing
reports.
 As per Standard Practice and our company policy for executing orders for similar requirement
in Refineries, we are not sharing any type of calculations regarding Mixer Design and Sizing as it
falls under our Proprietary Design Part
 Hydro test for Tank Jet Mixer is not applicable

Material of Construction:

Sr. No. Description MOC

1. Body SS 316
2. Nozzle SS 316
3. Flange SS 316, WNRF, As per ANSI B16.5, 150#

4. Gasket SS 316 Spiral Wound with Graphite Filler

5. Fasteners SA 193 Gr. B8 / SA 194 Gr. 8
*Note: Material of Construction selection is as per your requirement and compatibility suitability. We
do not stand guarantee for selection of MOC/Corrosion

Scope of Supply:

Sr. No. Description Qty.

SYSTEM-4: TANK JET MIXERS (REFORMATE TANK - TAG NO: 301-T-313) 1 No. per tank

ERECTION AND COMMISSIONING SPARES

1. Gaskets 200%
2. Fasteners (Min 2 Nos. stud and 4 Nuts) 10%
TWO YEAR OPERATIONAL SPARES
3. Gaskets 400%
4. Fasteners (Min 4 Nos. stud and 8 Nuts) 20%

TECHNICAL DATASHEET

SYSTEM 5-: TANK JET MIXERS (OCHU FEED TANK: - TAG NO: 301-T-308)
DESIGN DATA:

Sr. No. Particulars Unit Value

1. Application - Homogeneous
mixing
2. Tank Diameter mm 50000

Page 10 of 19
 3. Tank Height mm 18500
4. Tank HHLL Height mm 16259
5. Volume as per HHLL Height considered M3 31924
6. Total Tank capacity M3 36306
7. Fluid OCHU feed
8. Fluid Density Kg/m3 900
9. Viscosity cP 4.58-19.5
10. Operating Temperature (Normal / Max.) Deg C 80/ 100
11. Motive Liquid Pressure at inlet of Jet Mixer Kg/cm2(g) 5.4
12. Design Pressure Kg/cm2(g) 7.02
13. Design Temperature Deg C 150
14. Total Motive Flow Rate M3/hr 90
15. Motive Flow Rate per Mixer M3/hr 45
16. Mixing Time Hr. 23.94
17. No. of Mixer per Tank Nos. 2.0
18. Mixer Connection Size NB 100
19. O-Ring/ Header Size NB 200

Notes:
 Our Mixer will perform satisfactorily subjected to Mixer should be submerged, Driving Flowrate
and Pressure from pump for Mixer should operate at Designed parameters i.e. pressure, flow
rate and Specific Gravity of fluid
 We have not considered cost of appointing Third Party Inspection. Same is to be appointed by
M/s. Apollo International Limited.
 We will provide scanned copy of MTC. In absence of the same we will provide check testing
reports.
 As per Standard Practice and our company policy for executing orders for similar requirement
in Refineries, we are not sharing any type of calculations regarding Mixer Design and Sizing as it
falls under our Proprietary Design Part
 Hydro test for Tank Jet Mixer is not applicable

Material of Construction:

Sr. No. Description MOC

1. Body SS 316

Page 11 of 19
 2. Nozzle SS 316
3. Flange SS 316, WNRF, As per ANSI B16.5, 150#

4. Gasket SS 316 Spiral Wound with Graphite Filler

5. Fasteners SA 193 Gr. B8 / SA 194 Gr. 8
*Note: Material of Construction selection is as per your requirement and compatibility suitability. We
do not stand guarantee for selection of MOC/Corrosion

Scope of Supply:

Sr. No. Description Qty.

SYSTEM-5: TANK JET MIXERS (OCHU FEED TANK - TAG NO: 301-T-308) 2 Nos. per Tank

ERECTION AND COMMISSIONING SPARES

1. Gaskets 200%
2. Fasteners (Min 2 Nos. stud and 4 Nuts) 10%
TWO YEAR OPERATIONAL SPARES
3. Gaskets 400%
4. Fasteners (Min 4 Nos. stud and 8 Nuts) 20%

TECHNICAL DATASHEET

SYSTEM 6-: TANK JET MIXERS (OCHU FEED TANK: - TAG NO: 301-T-309)
DESIGN DATA:

Sr. No. Particulars Unit Value

1. Application - Homogeneous
mixing
2. Tank Diameter mm 27000
3. Tank Height mm 18000
4. Tank HHLL Height mm 15823
5. Volume as per HHLL Height considered M3 9059
6. Total Tank capacity M3 10300
7. Fluid OCHU feed
8. Fluid Density Kg/m3 900
9. Viscosity cP 4.58-19.5
10. Operating Temperature (Normal / Max.) Deg C 80/ 100
2
11. Motive Liquid Pressure at inlet of Jet Mixer Kg/cm (g) 5.4

Page 12 of 19
 12. Design Pressure Kg/cm2(g) 7.02
13. Design Temperature Deg C 150
14. Total Motive Flow Rate M3/hr 90
15. Motive Flow Rate per Mixer M3/hr 45
16. Mixing Time Hr. 6.79
17. No. of Mixer per Tank Nos. 2.0
18. Mixer Connection Size NB 100
19. O-Ring/ Header Size NB 200

Notes:
 Our Mixer will perform satisfactorily subjected to Mixer should be submerged, Driving Flowrate
and Pressure from pump for Mixer should operate at Designed parameters i.e. pressure, flow
rate and Specific Gravity of fluid
 We have not considered cost of appointing Third Party Inspection. Same is to be appointed by
M/s. Apollo International Limited.
 We will provide scanned copy of MTC. In absence of the same we will provide check testing
reports.
 As per Standard Practice and our company policy for executing orders for similar requirement
in Refineries, we are not sharing any type of calculations regarding Mixer Design and Sizing as it
falls under our Proprietary Design Part
 Hydro test for Tank Jet Mixer is not applicable

Material of Construction:

Sr. No. Description MOC

1. Body SS 316
2. Nozzle SS 316
3. Flange SS 316, WNRF, As per ANSI B16.5, 150#

4. Gasket SS 316 Spiral Wound with Graphite Filler

5. Fasteners SA 193 Gr. B8 / SA 194 Gr. 8
*Note: Material of Construction selection is as per your requirement and compatibility suitability. We
do not stand guarantee for selection of MOC/Corrosion

Scope of Supply:

Sr. No. Description Qty.

Page 13 of 19
SYSTEM-6: TANK JET MIXERS (OCHU FEED TANK - TAG NO: 301-T-309) 2 Nos. per Tank

ERECTION AND COMMISSIONING SPARES

1. Gaskets 200%
2. Fasteners (Min 2 Nos. stud and 4 Nuts) 10%
TWO YEAR OPERATIONAL SPARES
3. Gaskets 400%
4. Fasteners (Min 4 Nos. stud and 8 Nuts) 20%

TECHNICAL DATASHEET

SYSTEM 7-: TANK JET MIXERS (ISOMERATE TANK: - TAG NO: 301-T-314)
DESIGN DATA:

Sr. No. Particulars Unit Value

1. Application - Homogeneous
mixing
2. Tank Diameter mm 20000
3. Tank Height mm 14700
4. Tank HHLL Height mm 13301
5. Volume as per HHLL Height considered M3 4179
6. Total Tank capacity M3 4615
7. Fluid Isomerate
8. Fluid Density Kg/m3 650
9. Viscosity cP 0.276-0.765
10. Operating Temperature (Normal / Max.) Deg C 50/ 60
11. Motive Liquid Pressure at inlet of Jet Mixer Kg/cm2(g) 10
12. Design Pressure Kg/cm2(g) 13
13. Design Temperature Deg C 65
14. Total Motive Flow Rate M3/hr 78
15. Motive Flow Rate per Mixer M3/hr 78
16. Mixing Time Hr. 2.04
17. No. of Mixer per Tank Nos. 1.0
18. Mixer Connection Size NB 100
19. O-Ring / Header NB Not Required

Page 14 of 19
Notes:
 Our Mixer will perform satisfactorily subjected to Mixer should be submerged, Driving Flowrate
and Pressure from pump for Mixer should operate at Designed parameters i.e. pressure, flow
rate and Specific Gravity of fluid
 We have not considered cost of appointing Third Party Inspection. Same is to be appointed by
M/s. Apollo International Limited.
 We will provide scanned copy of MTC. In absence of the same we will provide check testing
reports.
 As per Standard Practice and our company policy for executing orders for similar requirement
in Refineries, we are not sharing any type of calculations regarding Mixer Design and Sizing as it
falls under our Proprietary Design Part
 Hydro test for Tank Jet Mixer is not applicable

Material of Construction:

Sr. No. Description MOC

1. Body SS 316
2. Nozzle SS 316
3. Flange SS 316, WNRF, As per ANSI B16.5, 150#

4. Gasket SS 316 Spiral Wound with Graphite Filler

5. Fasteners SA 193 Gr. B8 / SA 194 Gr. 8
*Note: Material of Construction selection is as per your requirement and compatibility suitability. We
do not stand guarantee for selection of MOC/Corrosion

Scope of Supply:

Sr. No. Description Qty.

SYSTEM-7: TANK JET MIXERS (ISOMERATE TANK: - TAG NO: 301-T-314) 1 No. per Tank

ERECTION AND COMMISSIONING SPARES

1. Gaskets 200%
2. Fasteners (Min 2 Nos. stud and 4 Nuts) 10%
TWO YEAR OPERATIONAL SPARES
3. Gaskets 400%
4. Fasteners (Min 4 Nos. stud and 8 Nuts) 20%

Exclusions:
 Any Kind of Civil Work at Site

Page 15 of 19
  Unloading of Material at Site & Erection of Material at Site
 Circulation Pump with Mechanical Seal and Motor
 Header in Tank, O ring
 Supply of special tools
 Monitoring Instruments i.e. Gauges, Transmitters etc. as applicable at immediate inlet of
Driving Flowrate to Mixer
 All Connecting Piping and Fittings, Valves
 Mixer Supports
 Ant type of Piping & Fittings
 Companion Flanges
 Appointment of Third Party Inspector for Inspection at our Factory
 Performance of equipment at our works
 Any other items not specified in scope

PRICE BID:
(FOR- INDIAN OIL CORPORATION LIMITED (IOCL) BARAUNI)

Sr. No. Description Qty. of Qty. of Tanks Total Qty Total Finalized Price Bid
Mixers (As per your of Mixers inclusive of E&C Spares, Two
per Technical for Total Years Operational Spares,
Tank Specification) Nos. of P&F and Freight upto IOCL
Tanks Barauni Site
(Client Scope)
1. SYSTEM-1: TANK JET MIXERS (MS 8 Nos. 2 Nos. 16 Nos.
TANK - TAG NO: 301-T-303/ 304) Per
Tank
2. SYSTEM-2: TANK JET MIXERS 6 Nos. 1 No. 6 Nos.
(NAPHTHA TANK: - TAG NO: 301- Per
T-307) Tank *****
3. SYSTEM-3: TANK JET MIXERS 1 No. 2 Nos. 2 Nos.
(SRN TANK - TAG NO: 301-T- Per
311/312) Tank
4. SYSTEM-4: TANK JET MIXERS 1 No. 1 No. 1 No.
(REFORMATE TANK - TAG NO: Per
301-T-313) Tank
5. SYSTEM-5: TANK JET MIXERS 2 Nos. 1 No. 2 Nos.
(OCHU FEED TANK - TAG NO: 301- Per
T-308) Tank
6. SYSTEM-6: TANK JET MIXERS 2 Nos. 1 No. 2 Nos.
(OCHU FEED TANK - TAG NO: 301- Per
T-309) Tank
7. SYSTEM-7: TANK JET MIXERS 1 No. 1 No. 1 No.

Page 16 of 19
 (ISOMERATE TANK: - TAG NO: Per
301-T-314) Tank

ERECTION & COMMISSIONING SPARES:

Sr. No. Description Qty of Qty. of Tanks Total Qty Unit Set Total Price for
Spares (Client Scope) of Spares Price for Per Total Nos. of
Per for Total Tank Tank
Tank Nos. of
Tank
1. Erection & Commissioning Spares 1 Set. 2 Nos. 2 Set.
for SYSTEM-1: TANK JET MIXERS
(MS TANK - TAG NO: 301-T-303/
304)
Erection & Commissioning Spares 1 Set. 1 No. 1 Set.
for SYSTEM-2: TANK JET MIXERS
2. (NAPHTHA TANK: - TAG NO: 301-
T-307
Included in above Price
Erection & Commissioning Spares 1 Set. 2 Nos. 2 Set.
for SYSTEM-3: TANK JET MIXERS
3. (SRN TANK - TAG NO: 301-T-
311/312)
Erection & Commissioning Spares 1 Set. 1 No. 1 Set.
for SYSTEM-4: TANK JET MIXERS
4. (REFORMATE TANK - TAG NO:
301-T-313)
Erection & Commissioning Spares 1 Set. 1 No. 1 Set.
for SYSTEM-5: TANK JET MIXERS
5. (OCHU FEED TANK - TAG NO: 301-
T-308)
Erection & Commissioning Spares 1 Set. 1 No. 1 Set.
for SYSTEM-6: TANK JET MIXERS
6. (OCHU FEED TANK - TAG NO: 301-
T-309)
Erection & Commissioning Spares 1 Set. 1 No. 1 Set.
for SYSTEM-7: TANK JET MIXERS
7. (ISOMERATE TANK: - TAG NO:
301-T-314)

TWO YEARS SPARE PRICE:

Sr. No. Description Qty of Qty. of Tanks Total Qty Unit Set Total Price for
Spares (Client Scope) of Spares Price for Per Total Nos. of
Per Tank for Total Tank Tank
Nos. of
Tank

Page 17 of 19
1. Two Years Operation Spares for 1 Set. 2 Nos. 2 Set.
SYSTEM-1: TANK JET MIXERS
(MS TANK - TAG NO: 301-T-303/
304)
Two Years Operation Spares for 1 Set. 1 No. 1 Set.
SYSTEM-2: TANK JET MIXERS
2. (NAPHTHA TANK: - TAG NO: 301-
T-307
Included in above Price
Two Years Operation Spares for 1 Set. 2 Nos. 2 Set.
SYSTEM-3: TANK JET MIXERS
3. (SRN TANK - TAG NO: 301-T-
311/312)
Two Years Operation Spares for 1 Set. 1 No. 1 Set.
SYSTEM-4: TANK JET MIXERS
4. (REFORMATE TANK - TAG NO:
301-T-313)
Two Years Operation Spares for 1 Set. 1 No. 1 Set.
SYSTEM-5: TANK JET MIXERS
5. (OCHU FEED TANK - TAG NO:
301-T-308)
Two Years Operation Spares for 1 Set. 1 No. 1 Set.
SYSTEM-6: TANK JET MIXERS
6. (OCHU FEED TANK - TAG NO:
301-T-309)
Two Years Operation Spares for 1 Set. 1 No. 1 Set.
SYSTEM-7: TANK JET MIXERS
7. (ISOMERATE TANK: - TAG NO:
301-T-314)

Supervision of Erection and Commissioning:

Per Day Rate for Supervision Engineer: Rs. ***** Per day in General Shift Inclusive To and Fro

Below charges will be in your Scope:

a. Boarding & Lodging Expenses including at transits places (if any required)

b. Transportation from Hotel to work site and back- including during lunch break

c. All above charges are of net and does not include any taxes payable. If any taxes is
payable, it will be to your account.

Equipment Delivery
Within 10 weeks from date of receipt of Drawing Approval.

Packing & Forwarding

Included in above Price (Wooden Box Packing but Not Sea worthy)

Page 18 of 19
Payment Terms
20% Advance against Submission of ABG and Balance 80% against material readiness/Inspection before
dispatch along with submission of 5% PBG (PBG will valid till Warranty Period)

Taxes
18% GST (HSN Code – 84211999)

Warranty
As per below:
1. To perform in accordance with the details specified in the heading “Design data” in this
quotation.
2. Against faulty materials and workmanship For a period of 24 months from date of
commissioning or 30 months from the date of supply whichever is earlier.

Terms & Conditions of Sale

Any order resulting from this tender will not be binding unless acknowledged by CHEM in writing. Our
general terms and conditions of sale are attached to this quotation and apply to any resulting purchase
order unless agreed otherwise in writing. Prices are based on material prices and deliveries ruling at
date of tender.

Statutory & Regulatory Requirements

Compliance with any local government laws or regulations relating to location, use or the application of
service other than the service, for which the goods are sold, shall be the sole responsibility of the
purchaser. If due the specific nature of the application, you feel that any laws/regulations will apply,
please advise us accordingly. If applicable, compliance to such laws/regulations will be charged extra as
required.

General Clauses
Design
Unless otherwise stated in our quotation, the equipment offered is designed and manufactured to
Chem Process standard proprietary procedures which are based on sound engineering principles and
have been used successfully on many occasions for the design of similar equipment.

Page 19 of 19