STANDING SEAM

System Technology for Roofing

DESIGN AND APPLICATION

 STANDING SEAM, DESIGN AND APPLICATION

Residence in Capetown, South Africa

Mormon Temple, Tucson, AZ Geschäftshaus Wensler, New Church, Germany

Standing Seam Roof System 9. To determine whether a ventilation mat

1. This system may be fabricated from the 5. For cost effectiveness, ease of is required for RHEINZINK standing
following PRODUCT LINES: fabrication and installation, limit panel seam roofing panels, please refer to the
lengths to 40’, although the maximum RHEINZINK Steep Slope, Mid Slope and
allowable length of 52’ is possible. Low Slope Roofing recommendations.

Consult the RHEINZINK technical 10. All roof installations require Air-Z or Enkamat
department for applications requiring (7008 or 7010).
longer lengths.
11. Roof penetrations such as skylights, chimneys
6. It is recommended to single lock the panels or vents that interrupt the seams constitute
every 3’-4’ prior to seaming to assure the most vulnerable part of any standing
2. Easy to fabricate and install. proper seam closure. seam roof. These areas must be carefully
detailed fully with apron flashings with
3. Panel widths from 12” to 24”. 7. Refer to the RHEINZINK baseline details sufficient overlap lengths, capillary breaks,
for detail options for eaves, rakes, hips, and waterchecks. Consult a RHEINZINK
4. For optimum flatness: ridges, valleys and­­penetrations. Consult representative for advice on proper details
„ Use 0.8 mm thick RHEINZINK for the RHEINZINK technical department for for these conditions.
panel widths 17” to 24”. customized applications.
„ Use 0.7 mm thick RHEINZINK for
panel heights 12” to 17”. 8. Panels can be roll formed or fabrication
„ For panel widths above 18” addi- fabricated using brake forming or folding
tional profiling is recommended. machines.

Photo on page prior: Private Residence, Moskauer Gebiet, Russia

VOLUME 10
ROOF SLOPE CALCUILATIONS

Pitch Angle Roof Pitch in Percentage Roof Pitch in Degrees

1 : 12 3.75° 8.33% 4.76°

2 : 12 7.50° 16.67% 9.46°

3 : 12 11.25° 25.00% 14.04°

4 : 12 15.00° 33.33% 18.43°

5 : 12 18.75° 41.67% 22.62°

6 : 12 22.50° 50.00% 26.57°

7 : 12 26.25° 58.33% 30.26°

8 : 12 30.00° 66.67% 33.69°

9 : 12 33.50° 75.00% 36.87°

10 : 12 37.50° 83.33% 39.81°

11 : 12 41.25° 91.67% 42.51°

12 : 12 45.00° 100.00% 45.00°

1:12 2:12 3:12 4:12

5:12 6:12 7:12 8:12

9:12 10:12 11:12 12:12 VOLUME 10

 LOW SLOPE STANDING SEAM ROOFING WITH RHEINZINK

Roofing Application: Low Slope: (<3 in 12)

Double Lock Air Z or Enkamat (7008 or

7010)
Standing Seam:
0-10”
This application is
Angle Lock
not recommended
Standing Seam:
by RHEINZINK.

1. A roof with a pitch of 3 in12 or less cross seams. Panels must therefore run 10. Roof penetrations such as skylights, chimneys,
is a low slope roof. Barrel vaulted or the full length of the roof plane or arc. or vents that interrupt the seams constitute the
curved roofs usually have low slope Panels that are longer than 40’ will most most vulnerable part of any standing seam
conditions on at least a portion of the roof. likely have to be roll formed at the site. roof. These areas must be detailed carefully
with apron flashings with sufficient overlap
2. Low slope roofs require a high 5. Low slope roofs require the added lengths, capillary breaks, and water checks.
temperature, peel and stick, self adhesive weather resistance of a double locked seam. Consult your RHEINZINK representative for
membrane as the underlayment. Single lock seams are not appropriate for low advice on proper details for these conditions.
Breathable membranes are not appropriate slope roofs. Valleys should have a water
underlayments for low slope standing seam check and an additional soldered cleat 11. Terminate eave ends of panels by leaving
roof conditions. In cold climates where 10“ from the water check for engagement the underside of the eave hook horizontal to
roof assembly ventilation may be desirable, of the roof panels or other lengths of valley. facilitate drainage of leakage or condensation.
consideration should be given to the fact
that a peel and stick membrane is a non 6. In areas of high snow fall, the seam height 12. All roof installations require Air-Z or Enkamat
breathable vapor barrier and therefore does should be 1-1/2“ tall (instead of the standard (7008 or 7010).
not promote drying of condensation in the 1“) height for additional weather resistance.
roof assembly through the roof surface itself.
7. The standing seams should be sealed
3. Low slope standing seam roofs must have continuously with either butyl sealant or
continuous positive drainage at a minimum closed cell urethane foam placed on the
pitch of 5/8“ in 12. However, the steeper top of the male leg. The use of urethane
the pitch, the less chance of a leak especially foam requires an adjustment, prior to
in areas with extended snow cover. Also, fabricating, to the female leg of the seam to
valleys must have a minimum pitch of 5/8“ compensate for the thickness of the foam.
in 12. Beware! The resulting valley pitch of
two intersecting 5/8“ in 12 pitched roofs 8. Low slope roofs with pitches of less than
that are oriented perpendicularly to each 3 in 12 require the added protection
other is less than ½“ in 12. Low slope of both backside coating (ProRoofing)
roofs with long lengths should generally be and a drainage mat - RHEINZINK Air-Z
pitched greater than 5/8“ in 12 because or Enkamat (7008 or 7010) by Bonar.
over a larger roof plane there is a greater
chance that the supporting substrate 9. Attachment clips and their associated
will have swales that create puddles. fasteners for low slope standing seam
roofs should be made of stainless steel.
4. Low slope standing seam roofs with slopes
less than 3 in 12 should not have any
VOLUME 10
MID SLOPE STANDING SEAM ROOFING WITH RHEINZINK

Roofing Application: Mid Slope: (3 in 12 to 6 in 12)

Double Lock
Standing Seam:
Air Z or Enkamat (7008 or
0-6” 7010)

This application is
Angle Lock
not recommended
Standing Seam:
by RHEINZINK.

1. A roof with a pitch of 3 in 12 to 6 in 12 is 6. The standing seams can be sealed 10. Prevent water from getting under the metal
a mid slope roof. continuously with either butyl sealant or by either bread panning the panel ends at
closed cell urethane foam placed on the ridges and roof / wall intersections or by
2. On a mid slope roofs, breathable top of the male leg. The use of urethane some other means of a closure.
membranes are appropriate. High foam requires that the height of the male 11. Terminate eave ends of panels by leaving
temperature peel and stick self adhesive leg be shortened to create enough space the underside of the eave hook horizontal
membranes are recommended as the for the foam. to facilitate drainage of leakage or
underlayment at the eaves, rakes, hips, condensation.
ridges, valleys and around penetrations 7. Mid slope roofs with pitches of 3 in 12 to 6 in
such as chimneys, soil pipes, skylights, etc. 12 require the added protection of drainage 12. All roof installations require Air-Z or Enkamat
to maintain water tightness. mat - RHEINZINK Air-Z or Enkamat (7008 (7008 or 7010).
or 7010) by Bonar.
3. Mid slope standing seam roofs should have
cross seams consisting of a water check and 8. Attachment clips and their associated
an additional soldered cleat 6” from the fasteners for mid slope standing seam roofs
water check for the engagement of the roof should be made of stainless steel.
panels or other lengths of valley.
9. Roof penetrations such as skylights,
4. Mid slope roofs require the added weather chimneys, or vents that interrupt the seams
resistance of a double locked seam. Single constitute the most vulnerable part of any
lock seams are not appropriate for mid slope standing seam roof. These areas must be
roofs. detailed carefully with apron flashings
with sufficient overlap lengths, capillary
5. In areas of high snow fall, the seam breaks, and water checks. Consult your
height should be 1-1/2“ tall (instead of the RHEINZINK representative for advice on
standard 1“) height for additional weather proper details for these conditions.
resistance.
VOLUME 10
 STANDING SEAM ROOF PANELS, DETAILS

15a 5-7 3a,b 9-11

16

14 4a,b
8a,b,c

17a,b
1a,b

13

Standing Seam Roof Details

Standard Custom Details
SSR-1a - Eave Edge with Gutter SSR-1b - Eave Edge with Without Gutter
SSR-2 - Built-In Gutter Detail SSR-4b - Mono Pitch Ridge Detail - Option 2
SSR-3a - Ridge / Hip Detail - Option 1 SSR-12b - Roof to Wall Transition Detail - Option 2
SSR-3b - Ridge / Hip Detail - Option 2
SSR-4a - Mono Pitch Ridge Detail - Option 1
SSR-5 - Steep Slope Valley Detail
SSR-6 - Mid Slope Valley Detail
SSR-7 - Low Slope Valley Detail
SSR-8a - Rake Edge Detail - Option 1
SSR-8b - Rake Edge Detail - Option 2
SSR-8c - Rake Edge Detail - Option 3
SSR-9 - Steep Slope Cross Joint Detail
SSR-10 - Mid Slope Cross Joint Detail
SSR-11 - Low Slope Cross Joint Detail
SSR-12a - Roof to Wall Transition Detail - Option 1
SSR-13 - Sidewall Detail
SSR-14 - Skylight Sill Detail
SSR-15 - Skylight Head Detail
SSR-16 - Skylight Jamb Detail
SSR-17a - Vent Pipe Penetration Detail - Option 1
SSR-17b - Vent Pipe Penetration Detail - Option 2
VOLUME 10

SSR-18 - Panel Profile & Clip Detail

 STEEP SLOPE STANDING SEAM ROOFING WITH RHEINZINK

Roofing Application: Steep Slope: (> 6 in 12)

Double Lock
Standing Seam:

”
0-6
Angle Lock
Standing Seam: Air Z or Enkamat (7008
or 7010)

1. A roof with a pitch of 6 in 12 or greater is 6. The standing seams can be sealed breaks, and water checks. Consult a
a steep slope roof. continuously with either butyl sealant or RHEINZINK representative for advice
closed cell urethane foam placed on the on proper details for these conditions.
2. On steep slope roofs, breathable membranes top of the male leg. The use of urethane
are appropriate. High temperature peel foam requires that the height of the male 10. Prevent water from getting under the metal
and stick self adhesive membranes are leg be shortened to create enough space by either bread panning the panel ends at
recommended as the underlayment at for the foam. ridges and roof / wall intersections or by
the eaves, rakes, hips, ridges, valleys and some other means of a closure.
around penetrations such as chimneys, 7. Steep slope roofs with pitches of 6 in 12
soil pipes, skylights, etc. to maintain water or greater require the added protection 11. Terminate eave ends of panels by leaving
tightness. of drainage mat - RHEINZINK Air-Z or the underside of the eave hook horizontal
Enkamat (7008 or 7010) by Bonar. to facilitate drainage of leakage or
3. Steep slope standing seam roofs can have condensation.
cross seams consisting of single hook seam. 8. Attachment clips and their associated
This also applies to valleys. fasteners for steep slope standing seam 12. All roof installations require Air-Z or Enkamat
roofs can be made of stainless steel. (7008 or 7010).
4. Steep slope roofs can either be single locked
or double locked. 9. Roof penetrations such as skylights,
chimneys, or vents that interrupt the seams
5. In areas of high snow fall, the seam height constitute the most vulnerable part of any
should be 1-1/2“ tall (instead of the standing seam roof. These areas must be
standard 1“) height for additional weather detailed carefully with apron flashings
resistance. with sufficient overlap lengths, capillary

VOLUME 10
RHEINZINK America, Inc.

STANDING SEAM ROOF DETAILS

SSR-1a - EAVE EDGE DETAIL - WITH GUTTER

SSR-2a - BUILT-IN GUTTER DETAIL - OPTION 1
SSR-3a - RIDGE / HIP DETAIL - OPTION 1
SSR-3b - RIDGE / HIP DETAIL - OPTION 2
SSR-4a - MONO PITCH RIDGE DETAIL - OPTION 1
SSR-4b - MONO PITCH RIDGE DETAIL - OPTION 2
SSR-5a - STEEP SLOPE VALLEY DETAIL - OPTION 1
SSR-6a - MID SLOPE VALLEY DETAIL - OPTION 1
SSR-7a - LOW SLOPE VALLEY DETAIL - OPTION 1
SSR-8a - RAKE EDGE DETAIL - OPTION 1
SSR-8b - RAKE EDGE DETAIL - OPTION 2
SSR-8c - RAKE EDGE DETAIL - OPTION 3
SSR-9 - STEEP SLOPE CROSS JOINT DETAIL
SSR-10 - MID SLOPE CROSS JOINT DETAIL
SSR-11 - LOW SLOPE CROSS JOINT DETAIL
SSR-12a - ROOF TO WALL TRANSITION DETAIL - OPTION 1
SSR-13a - SIDEWALL DETAIL - OPTION 1
SSR-14 - SKYLIGHT SILL DETAIL
SSR-15a - SKYLIGHT HEAD DETAIL - OPTION 1
SSR-16 - SKYLIGHT JAMB DETAIL
SSR-17a - VENT PIPE PENETRATION DETAIL - OPTION 1
SSR-17b - VENT PIPE PENETRATION DETAIL - OPTION 2
SSR-18 - PANEL PROFILE & CLIP DETAIL

SSR-1b - EAVE EDGE DETAIL - WITH GUTTER

SSR-1c - EAVE EDGE DETAIL - WITHOUT GUTTER
SSR-2b - BUILT-IN GUTTER DETAIL
SSR-3c - RIDGE / HIP DETAIL
SSR-4c - MONO PITCH RIDGE DETAIL
SSR-5b - STEEP SLOPE VALLEY DETAIL
SSR-6b - MID SLOPE VALLEY DETAIL
SSR-7b - LOW SLOPE VALLEY DETAIL
SSR-12b - ROOF TO WALL TRANSITION DETAIL
SSR-13b - SIDEWALL DETAIL
SSR-15b - SKYLIGHT HEAD DETAIL
 RHEINZINK STANDING SEAM PANEL

AIR-Z or ENKAMAT (7008/7010)

CONTINUOUS SUPPORT ANGLE

UNDERLAYMENT
RHEINZINK STARTER
FLASHING

OPTIONAL FOLDED SEAM TAB END

OPTIONAL RHEINZINK PERFORATED
LEAF GUARD
2-1/4"
RHEINZINK GUTTER

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. EAVE EDGE - WITH GUTTER - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-1a
 RHEINZINK STANDING SEAM PANEL

AIR-Z or ENKAMAT (7008/7010)

CONTINUOUS SUPPORT ANGLE

UNDERLAYMENT
RHEINZINK STARTER
FLASHING

CRESCENT EAVE DETAIL

OPTIONAL RHEINZINK PERFORATED

LEAF GUARD
2-1/4"
RHEINZINK GUTTER

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE. .
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. EAVE EDGE - WITH GUTTER - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-1b
 RHEINZINK STANDING SEAM PANEL

AIR-Z or ENKAMAT (7008/7010)

OPTIONAL FOLDED SEAM TAB END

CONTINUOUS SUPPORT ANGLE

RHEINZINK STARTER
FLASHING

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. EAVE EDGE - WITHOUT GUTTER N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-1c
 RHEINZINK STANDING SEAM PANEL

UNDERLAYMENT

RHEINZINK STARTER
FLASHING
RHEINZINK BOX
GUTTER SLOPED TO
DRAIN
AIR-Z or ENKAMAT
(7008/7010)
MEMBRANE LINER
SLOPED TO DRAIN

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. BUILT-IN GUTTER DETAIL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-2a
 RHEINZINK STANDING SEAM PANEL

UNDERLAYMENT

RHEINZINK
STARTER FLASHING
RHEINZINK BOX
GUTTER SLOPED TO
DRAIN

AIR-Z or ENKAMAT
(7008/7010)

MEMBRANE LINER
SLOPED TO DRAIN

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE. .
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. BUILT-IN GUTTER DETAIL - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-2b
 RHEINZINK FLASHING

FOLDED BREADPAN END

RHEINZINK STANDING SEAM PANEL

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. RIDGE / HIP DETAIL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-3a
 RHEINZINK RIDGE FLASHING
4" MAX.

FOLDED BREADPAN END

RHEINZINK STANDING SEAM PANEL

AIR-Z or ENKAMAT (7008/7010)

RHEINZINK "Z" CHANNEL - SPOT
SOLDER 6" O.C.

UNDERLAYMENT

SHEATHING

1. STANDING SEAM PANELS REQUIRE A MIN. Website: www.rheinzink.com E-mail: [email protected]

OF 3:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
ON SLOPE. AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.

PROJECT: DATE:
3. RHEINZINK RECOMMENDS STAINLESS STEEL STANDING SEAM ROOF DETAILS 09-2024
FASTENERS AND CLIPS.
DRAWING TITLE: SCALE:
RIDGE / HIP DETAIL - OPT. 2 N.T.S.
4. MAX. 4" - NON-SUPPORTED RIDGE CAP - SUPPORT
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
NEEDED FOR WIDTHS GREATER THAN 4" RHEINZINK. SSR-3b
 RHEINZINK STANDING SEAM PANEL

"FLATTENED SEAM"
1" - 1-1/2" SEAM HEIGHT
AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

1. STANDING SEAM PANELS REQUIRE A MIN. Website: www.rheinzink.com E-mail: [email protected]

OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
ON SLOPE. AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.

PROJECT: DATE:
3. RHEINZINK RECOMMENDS STAINLESS STEEL STANDING SEAM ROOF DETAILS 09-2024
FASTENERS AND CLIPS. DRAWING TITLE: SCALE:
RIDGE / HIP DETAIL - OPT. 3 N.T.S.
4. ON LOWER PITCHED ROOF - MIN 2" SEAM ON RIDGE COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-3c
 RHEINZINK FLASHING

FOLDED BREADPAN END

RHEINZINK STANDING SEAM ROOF PANEL

RHEINZINK STARTER FLASHING

CONTINUOUS SUPPORT ANGLE

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE. .
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. MONO PITCH RIDGE DETAIL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-4a
 RHEINZINK FLASHING

FOLDED BREADPAN END

RHEINZINK STANDING SEAM ROOF PANEL

RHEINZINK STARTER FLASHING

CONTINUOUS SUPPORT ANGLE

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. MONO PITCH RIDGE DETAIL - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-4b
 RHEINZINK STANDING SEAM ROOF PANEL

AIR-Z or ENKAMAT (7008/7010)

RHEINZINK STARTER FLASHING

CONTINUOUS STARTER FLASHING

UNDERLAYMENT

SHEATHING

1. STANDING SEAM PANELS REQUIRE A MIN. Website: www.rheinzink.com E-mail: [email protected]

OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
ON SLOPE. AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.

PROJECT: DATE:
3. RHEINZINK RECOMMENDS STAINLESS STEEL STANDING SEAM ROOF DETAILS 09-2024
FASTENERS AND CLIPS.
DRAWING TITLE: SCALE:
MONO PITCH RIDGE DETAIL - OPT. 3 N.T.S.
4. THIS DETAIL MAY ONLY BE USED ON A ROOF PITCH OF
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
4:12 OR GREATER. RHEINZINK. SSR-4c
 RHEINZINK STANDING SEAM ROOF PANEL

FASTENER*

STAINLESS STEEL CLIPS**

OPTIONAL FOLDED TABS AT SEAM END

RHEINZINK VALLEY FLASHING

AIR-Z or ENKAMAT
(7008/7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. STEEP SLOPE VALLEY DET. - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-5a
 STANDING SEAM PANEL

FASTENER*

STAINLESS STEEL CLIP

RHEINZINK VALLEY FLASHING

AIR-Z or ENKAMAT (7008 / 7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. STEEP SLOPE VALLEY DET. - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-5b
 FASTENER*

STAINLESS STEEL CLIP**

RHEINZINK STANDING SEAM PANEL

SOLDER 6" O.C.

RHEINZINK CLEAT**

RHEINZINK VALLEY FLASHING

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

0"
0'-1

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. MID SLOPE VALLEY DET. - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-6a
 FASTENER*

STAINLESS STEEL CLIP**

RHEINZINK STANDING SEAM PANEL

SOLDER 6" O.C.

RHEINZINK CLEAT**

RHEINZINK VALLEY FLASHING

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

"
0- 10

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. MID SLOPE VALLEY DET. - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-6b
 FASTENER*

STAINLESS STEEL CLIP**

RHEINZINK STANDING SEAM PANEL

SOLDER 6" O.C.

RHEINZINK CLEAT**

RHEINZINK VALLEY FLASHING

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

0'-10"

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. LOW SLOPE VALLEY WALL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-7a
 FASTENER*

STAINLESS STEEL CLIP**

RHEINZINK STANDING SEAM PANEL

SOLDER 6" O.C.

RHEINZINK CLEAT**

RHEINZINK VALLEY FLASHING

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

0'-10"

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. LOW SLOPE VALLEY WALL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-7b
 RHEINZINK STANDING SEAM ROOF PANEL

AIR-Z or ENKAMAT (7008/7010)

RHEINZINK STARTER FLASHING

CONTINUOUS SUPPORT ANGLE

UNDERLAYMENT

SHEATHING

10"

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. RAKE EDGE DETAIL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-8a
 RHEINZINK STANDING SEAM ROOF PANEL

AIR-Z or ENKAMAT (7008/7010)

RHEINZINK STARTER FLASHING

CONTINUOUS SUPPORT ANGLE

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. RAKE EDGE DETAIL - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-8b
 RHEINZINK STANDING SEAM ROOF PANEL

AIR-Z or ENKAMAT (7008/7010)

RHEINZINK STARTER FLASHING

CONTINUOUS SUPPORT ANGLE

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3.) RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. RAKE EDGE DETAIL - OPT. 3 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-8c
 RHEINZINK STANDING SEAM ROOF PANEL

FASTENER

STAINLESS STEEL CLIPS**

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 6:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE ENKAMAT DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
(7008 OR 7010); SEE REQUIREMENTS BASED ON SLOPE. DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.

3. RHEINZINK RECOMMENDS STAINLESS STEEL PROJECT:

STANDING SEAM ROOF DETAILS
DATE:
09-2024
FASTENERS AND CLIPS.
DRAWING TITLE: SCALE:
STEEP SLOPE CROSS JOINT DETAIL N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-9
 FASTENER

STAINLESS STEEL CLIP

RHEINZINK STANDING SEAM ROOF PANEL

SOLDER 6" O.C.

RHEINZINK CLEAT

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

0"
0 '- 1

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 3:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. MID SLOPE CROSS JOINT DETAIL N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-10
 FASTENERS

STAINLESS STEEL CLIP

RHEINZINK STANDING SEAM ROOF PANEL

SOLDER 6" O.C.

RHEINZINK CLEAT

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

0'-10"

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 2:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. LOW SLOPE CROSS JOINT DETAIL N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-11
 RHEINZINK STANDING SEAM
FACADE PANEL

FOLDED BREADPAN END

RHEINZINK FLASHING

RHEINZINK "Z" CHANNEL

RHEINZINK STANDING SEAM ROOF PANEL

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. ROOF TO WALL TRANS. - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-12a
 CONTINUOUS "PINCHED" SEAM

RHEINZINK STANDING SEAM PANEL

AIR-Z or ENKAMAT (7008/ 7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. ROOF TO WALL TRANS. - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-12b
 FACADE PANEL

RHEINZINK STANDING SEAM ROOF PANEL

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

3" max.

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. SIDEWALL DETAIL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-13a
 FASTENER

STAINLESS STEEL CLIP

RHEINZINK STANDING SEAM
FACADE PANEL

SOLDER 6" O.C.

RHEINZINK CLEAT

RHEINZINK STANDING SEAM ROOF PANEL

AIR-Z or ENKAMAT (7008/ 7010)

UNDERLAYMENT

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.

OF 5/8:12 SLOPE. INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED
ON SLOPE. PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL DRAWING TITLE: SCALE:
SIDEWALL DETAIL - OPT. 2 N.T.S.
FASTENERS AND CLIPS.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-13b
 FASTENER

STAINLESS STEEL CLIP

RHEINZINK FLASHING

SOLDER 6" O.C.

RHEINZINK CLEAT

IN.
4" M
AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

"FLATTENED" SEAM

"
0'-10

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. SKYLIGHT SILL DETAIL N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-14
 RHEINZINK STANDING SEAM PANEL

FASTENER

STAINLESS STEEL CLIP

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

SOLDERED 6" O.C.

RHEINZINK CLEAT
4" M
IN.

RHEINZINK
CRICKET

"
0'-10

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. SKYLIGHT HEAD DETAIL - OPT. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-15a
 RHEINZINK STANDING SEAM ROOF PANEL

FASTENER

STAINLESS STEEL CLIP

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

SOLDERED 6" O.C.

RHEINZINK CLEAT**
4" M
IN.

"
0'-10

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. SKYLIGHT HEAD DETAIL - OPT. 2 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-15b
 RHEINZINK STANDING SEAM PANEL

FASTENER

STAINLESS STEEL CLIPS

AIR-Z or ENKAMAT (7008/7010)

UNDERLAYMENT

SHEATHING

4" MIN.

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. SKLYLIGHT JAMB DETAIL N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-16
 SEALANT

PIPE CLAMP

RHEINZINK SHROUD

PROVIDE GAP BETWEEN PIPE COVER AND

VENT TO ALLOW FOR THERMAL EXPANSION
AND CONTRACTION OF PANEL

RHEINZINK PIPE COVER

UNDERLAYMENT

VENT PIPE

RHEINZINK STANDING SEAM ROOF PANEL

SOLDERED JOINT

AIR-Z or ENKAMAT (7008/7010)

SHEATHING

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. VENT PIPE PENETRATION - OP. 1 N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-17a
 SOLDER JOINT

PROVIDE GAP BETWEEN PIPE COVER AND

VENT TO ALLOW FOR THERMAL EXPANSION
AND CONTRACTION OF PANEL

RHEINZINK PIPE COVER

UNDERLAYMENT

VENT PIPE

RHEINZINK STANDING SEAM ROOF PANEL

SOLDERED JOINT

AIR-Z or ENKAMAT (7008/7010)

SHEATHING

1. STANDING SEAM PANELS REQUIRE A MIN.

OF 5/8:12 SLOPE. Website: www.rheinzink.com E-mail: [email protected]

2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ON SLOPE. DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.

3. RHEINZINK RECOMMENDS STAINLESS STEEL PROJECT: DATE:

FASTENERS AND CLIPS. STANDING SEAM ROOF DETAILS 09-2024
DRAWING TITLE: SCALE:
4. PENETRATION MUST BE PANNED IF PIPE FALLS VENT PIPE PENETRATION - OP. 2 N.T.S.
AT JOINT / RIB COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-17b
 1. ALL DIMENSIONS ARE INCHES OR FRACTIONS THEREOF.
2. MATERIAL .7mm OR .8mm RHEINZINK PREWEATHERED
TITANIUM ZINC.

3
1/2" 8"
5
64" BENDING RADIUS 5
64" BENDING RADIUS

3
8"
° 1" 1"
85

BASED ON 1/2 COIL FABRICATION WITDH

STANDARD SIZE = VARIES
3
8"
1/2" 5
64" BENDING RADIUS 5
64" BENDING RADIUS

3
8"

° 1-1/2" 1-1/2"
85

BASED ON 1/2 COIL FABRICATION WITDH

STANDARD SIZE = VARIES

DOUBLE LOCK ANGLED DOUBLE ROLL CAP - 2"

STANDING STANDING SEAM ANGLED SEAM HEIGHT
SEAM SLOPE > 25° (6:12) STANDING SLOPE >5°
SLOPE > 3° SLOPE > 35° (9:12) IN SEAM (1:12)
(5/8:12) AREAS OF HIGH SLOPE > 25°
SNOW (6:12)

Website: www.rheinzink.com E-mail: [email protected]

1. STANDING SEAM PANELS REQUIRE A MIN.
OF 5/8:12 SLOPE.
INFORMATION AND DETAILS HEREIN ARE ONLY A BASELINE FOR SYSTEM DESIGN AND
INSTALLATION. MODIFICATION TO MEET PROJECT REQUIREMENTS IS THE RESPONSIBILITY OF THE
2. STANDING SEAM PANEL SYSTEMS REQUIRE AIR-Z OR DESIGNER AND ARCHITECT. RHEINZINK AMERICA STAFF ARE AVAILABLE TO ASSIST THE
ENKAMAT (7008 OR 7010); SEE REQUIREMENTS BASED DESIGNER AND ARCHITECT IN THIS PROCESS. RHEINZINK AMERICA MAKES NO REPRESENTATIONS
AND WARRANTIES OTHER THAN THOSE EXPRESSED HEREIN.
ON SLOPE.
PROJECT: DATE:
STANDING SEAM ROOF DETAILS 09-2024
3. RHEINZINK RECOMMENDS STAINLESS STEEL
DRAWING TITLE: SCALE:
FASTENERS AND CLIPS. PANEL PROFILE & CLIP DETAIL N.T.S.
COPYRIGHT RESERVED. THIS DRAWING REMAINS THE PROPERTY OF SHEET:
RHEINZINK. SSR-18
SECTION 07 61 13 – STANDING SEAM ZINC ROOFING

PART 1 - GENERAL

1.01 RELATED DOCUMENTS

A. All of the Contract Documents, including General and Supplementary Conditions and Division 1
Specification Sections, apply to the work of this Section.

B. Examine all Drawings and all other Sections of the Specifications for requirements therein affecting
the work of this Section.

C. Coordinate work with that of all other trades affecting or affected by work of this Section. Cooperate
with such trades to assure the steady progress of all work under the Contract.

1.02 DESCRIPTION OF WORK

A. The Work of this Section shall include, but not be limited to, the following:

1. Custom fabricated, mechanically attached, [RHEINZINK-CLASSIC bright rolled,

RHEINZINK-prePATINA blue-grey, RHEINZINK-prePATINA graphite-grey, RHEINZINK-
GRANUM skygrey, RHEINZINK-GRANUM basalte, RHEINZINK-artCOLOR various colors
and PRISMO various colors] zinc alloy [reveal and shiplap panels] [vertical or horizontal]
as indicated on the Drawings, with all required accessories for a weatherproof installation.
2. [Zinc gutters and downspouts] as indicated on the Drawings.
3. Zinc coping and wall trim as indicated on the Drawings
4. Penetrations [doors, windows, louvers, etc…] in the wall assembly as indicated on the
Drawings.

B. Related Sections:

1. Section 05400 – Cold Formed Metal Framing

2. Section 06100 – Rough Carpentry
3. Section 07210 – Building Insulation
4. Section 07265 – Air and Vapor Barrier Membrane
5. Section 07410 – Metal Wall Panel Systems
6. Section 07500 – Membrane Roofing
7. Section 07620 – Sheet Metal Flashing and Trim
8. Section 07720 – Roof Accessories
9. Section 07920 – Joint Sealants

1.03 REFERENCES

1. ASTM B69-16 (or latest edition) – Architectural Rolled Zinc - Types 1 and 2 – Standard
Specification for rolled zinc.

2. RHEINZINK Division 7 Binder: latest edition.

3. RHEINZINK Material and Processing Guidelines: latest edition

4. SMACNA – Architectural Sheet Metal Manual; latest edition; Chapter 7 as a minimum standard or
these specification and details where they exceed.

5. Names of the applicable building codes or other authorities having jurisdiction:

______________________________________________________

6. As all documents are intended to be complementary, in the event of contradiction in the references,
the RHEINZINK Division 7 Binder; latest edition will govern.

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 1 of 9
1.04 SUBMITTALS

A. Product Data: provide zinc manufacturer’s product data for zinc sheet material including any
fabricator’s product specifications, standard details, and installation instructions. Indicate installer’s
intent for roof tile fabrication by shop fabrication or pre-manufactured zinc tiles.

B. Installer References: Installer shall submit list of (3) completed “natural metal” roof installations
(zinc or copper) of similar scope and complexity.

C. Material Samples: submit [RHEINZINK-CLASSIC bright rolled, RHEINZINK-prePATINA blue-grey,

RHEINZINK-prePATINA graphite-grey, RHEINZINK-GRANUM skygrey, RHEINZINK-GRANUM
basalte, RHEINZINK-artCOLOR - various colors and PRISMO – various colors] color samples of
each material that is to be exposed in the finished work. As required by architect, also provide two
fabricated panel samples to demonstrate connection.

D. Shop Drawings: show layouts of tiles on all roof plans, location of all roof penetrations, details of
tile terminations, edge conditions, joints, corners, tile profiles, supports, anchorages, trim, flashings,
closures, and special details. Distinguish between factory and field assembly work. Provide actual
dimensions to the greatest extent possible.

1. Details for forming sheet metal components including dimensions.

2. Details for joining and securing sheet metal components, including wood sub framing, clip
spacing, fastener requirements, and other attachments.
3. Details of termination points and assemblies, including fixed points.
4. Details of expansion joints, including showing direction of expansion.
5. Details of roof penetrations.
6. Details of edge conditions, including eaves, ridges, valleys, rakes, crickets and counter
flashings.
7. Details of special conditions, integrating mechanical, electrical and plumbing conditions.
8. Details of connections to adjoining work
9. Details of the following accessory items, at a scale of not less than 1 ½ inches per 12
inches:
a. Flashing and Trim
b. Fin Gutters
c. Gutters including outlet locations and expansion joints
d. Downspouts
e. Snow Guards
f. Roof Access Steps
g. Safety Line Attachments

E. [Engineering Calculations: As required by Architect, Installer to provide wind load (positive and
negative pressure) calculations based on substrate [exterior sheathing, galvanized steel sub-
framing] information provided by the Contractor. Calculations to utilize fastener pullout data and
known panel physical properties to provide “estimated” design performance. Submit written
certification showing calculations prepared and stamped by a Professional Structural Engineer
licensed and registered in the project state.]

1.05 QUALITY ASSURANCE

A. Fabricator/Installer Qualifications: The fabricator and installer of the wall panel system shall be
trained by the zinc material manufacturer [and system fabricator]. Installer shall submit list of three
(3) successful “natural metal” project installations of similar complexity and scope.

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 2 of 9
 B. Source: Provide panels, which are the product of one manufacturer. Provide secondary materials,
which are acceptable to the zinc manufacturer. Award installation of zinc roof panels, including
weather-barrier underlayment to a single firm for undivided responsibility.

C. Comply with RHEINZINK Division 7 Binder; latest edition and SMACNA-Architectural Sheet Metal
Manual; latest edition for flashings and sheet metal work.

D. Field Measurements: Prior to fabrication of roof tile and flashing, take field measurements of
structure or substrates to ensure proper fit and alignment.

E. Pre-Installation Conference: Two weeks prior to commencement of work, convene an installation

conference to include the Architect, General Contractor and Zinc roof Installer in order to establish
procedures to maintain optimum working conditions and to coordinate this work with related and
adjacent work.

1. Review methods and procedures for installation including, but not limited to: substrates,
subframing, drains, curbs, and penetrations.
2. Review drawings, specifications, & roof submittals.
3. Review construction schedule verifying availability of all materials, personnel and
equipment needed to proceed and avoid delays.
4. Review weather and forecasted weather conditions and procedures for coping with
unfavorable conditions, including cold temperatures and temporary roofing.

F. Mock-Up: As determined by the architect, Contractor to provide roof carpentry for mockup ready for
zinc roof panel installation. Incorporate materials and methods of fabrication and installation
identical with project requirements. Install mock-up at roof area location directed by Architect.
Retain accepted mock-up as quality standard for acceptance of completed metal roofing. As
appropriate, mock-up may be incorporated as part of final metal roofing work.

1. Provide mock-up of sufficient size and scope to show panel width/length, edge
construction, a sample of soldering (where required) and finish texture and color.
2. Provide mock-up of gutter and eave assembly.
3. Extent of mock-ups is indicated on the Drawings.
4. Obtain Architect’s written approval of mock-ups prior to proceeding.

G. Soldering: In accordance with zinc manufacturer’s instructions.

H. Corrosion Control: Contractor to avoid direct contact of incompatible materials including but not
limited to copper, red rosin paper and masonry cleaning solutions.

1.06 PERFORMANCE REQUIREMENTS

A. Design roof assembly to conform to the requirements of the _______ Building Code.

B. Minimum roof slope/pitch is 3˚ (5/8”:12) with conditions

C. Install sheet metal roofing panels and underlayment system capable of withstanding exposure to
weather without failure or infiltration of water into the building interior.

D. Wind Load: Design and engineer sheet metal roof assemblies, including size and spacing of
attachment devices, meeting requirements of local building codes.

E. Thermal Movement: Provide systems and detail connections which allow for thermal movement
resulting from ambient temperature range of -4° F to 176° F.

F. Structural Performance: Provide metal panels, anchors and attachments which resist loads
required by code and loads as indicated on the Drawings without permanent deflection or
deformation. Information on Drawings referring to specific design of attachment, panel stiffening,
and structural systems is intended for information only. System performance, based on project

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 3 of 9
 conditions and compliance with all applicable codes and loading requirements, shall be the
responsibility of the panel fabricator and installer.

DELIVERY, STORAGE AND HANDLING

A. Deliver materials and products in unopened factory labeled packages. Protect from all possible
damage. All zinc sheet, coil, and shop fabricated panels to be crated and transported according to
zinc manufacturer’s and fabricator’s recommendations.

B. Store and handle in strict compliance with zinc manufacturer’s instructions and recommendations.

1. Stack materials on platforms or pallets, covered with tarpaulins or other suitable weather
tight ventilated covering. Slope cover to shed moisture. Allow for free air flow around
covered material to exchange outside air.
2. Require all personnel to wear clean white cotton gloves when handling and installing zinc
panels and accessories when no strippable film is present.
3. Do not store panels in contact with other materials that might cause staining, denting, or
other surface damage.
4. Store all zinc panels & flashings so that they will not accumulate water.

C. Exercise care in unloading, storing, and erecting panels to prevent bending, warping, or surface
damage.

D. Sequence deliveries to avoid delays, but minimize on-site storage.

E. Contractor to deny other trades onto finished roof without permission of zinc installer. Installer to
limit unnecessary walking on finished roof. Require all personnel to wear uncontaminated, clean,
rubber soled shoes when installing or walking on roof.

1.07 WARRANTY

A. Material Only Warranty: provide X-year limited warranty for Titanium-Zinc alloy from original rolling
mill manufacturer. Warranty to cover the material quality of the sheet/ coil material used to
fabricate sheet metal flashing & trim profiles appropriate for zinc installation.

B. Fabrication Warranty: provide X-year fabrication warranty against sharp bends that fracture the
metal, tears, and equipment induced damage to the Architectural Zinc sheet or coil.

C. Installation Warranty: provide X-year guarantee covering the proper material or product application
preventing failure due to hot-water corrosion, damage due to inappropriate slip sheet, absorptive
separation material, or other installer induced failure.

PART 2 – PRODUCTS

2.01 MANUFACTURERS

A. Approved Zinc Manufacturer: Subject to compliance with requirements, manufacturers offering

metal roof or wall panel materials that may be incorporated in the work include:

1. RHEINZINK America, Inc.

www.rheinzink.us, [email protected]

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 4 of 9
 B. Zinc Alloy Sheet/Coils:
1. Titanium Zinc Alloy whose base is electrolytic high grade with a 99.995 % Zn degree of
purity and alloying additives of 0.08% - 1.0% copper and 0.07% - .12% titanium, .001% -
.015% aluminum in accordance with ASTM B69-16 (or latest edition) – Architectural
Rolled Zinc - Type 1 and Type 2.

a. RHEINZINK-CLASSIC bright rolled

b. RHEINZINK-prePATINA: pickling process
1. blue-grey
2. graphite-grey
c. RHEINZINK-GRANUM: phosphating process
1. sky-grey
2. basalte
d. RHEINZINK-PRISMO - PVDF finish
1. various colors

C. Standing Seam panels require a minimum of 5/8:12 pitch.

a. Double Lock Standing Seam: Low Slope (<3:12): Require Air-Z (or Enkamat
7008 or 7010).
b. Double Lock Standing Seam: Mid Slope (3:12 to 6:12): Require Air-Z (or
Enkamat 7008 or 7010).
c. Double Lock or Angled Lock Standing Seam: Steep Slope (>6:12): Require
Air-Z (or Enkamat 7008 or 7010).

2. Minimum Panel Thickness: [0.7mm (24 ga.), 0.8 mm (22 ga.), 1.0 mm (20 ga.)]
3. Minimum Flashing Thickness: 0.7 mm (24 ga.)

B. Panel Fabricator or System Manufacturer:

1. Local / Regional Sheet Metal Fabrication Shop:

a. Select roof tile fabricator that has the equipment and personnel capable of
providing quality zinc roof panels as indicated on the drawings.
b. Installer’s option to purchase prefabricated wall panels as provided by an
approved and experienced RHEINZINK system partner or fabricator.

2.02 PROFILES

A. Mechanical Double Lock Seam

1. Panel seam height/: 1” – 1 1/2”

2. Pan width/ seam spacing: ± 15 ½” – 16 ½” (panel is made from a ½ meter coil 19.7”).

2.03 ACCESSORIES

A. Provide all components necessary for a complete, functional, weatherproof assembly including, but
not limited to, trims, copings, fascias, sills, flashings, counter flashings, door frame trim, corner
units, clips, wall caps, copings, sealants, closures and fillers. Metal materials shall match panels
and be zinc compatible.

B. Clips & Fasteners: Provide stainless steel concealed clips and fasteners; supplied in accordance
with manufacturer’s recommendations and to meet the load requirements as specified by architect
and confirmed by engineering calculations. When using AIR-Z by RHEINZINK or Enkamat (7008 or
7010) by Bonar, Enka, NC. Use clips that are ¼” taller than the seam or a shim between the clip
and the AIR-Z or Enkamat.

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 5 of 9
 C. Roof structured mat (capillary break): As indicated on drawings (but not required on façade
applications), provide manufacturer’s approved nylon, non-woven, structured mat equal to AIR-Z by
RHEINZINK or Enkamat (7008 or 7010) by Bonar, Enka, NC.

D. Self-adhered Waterproof Underlayment: non-permeable self-adhering, high-temperature

composite, butyl rubber-based, polyethylene-backed membrane such as GRACE Ultra™ or other
high-temperature rubberized-asphalt sheet.

E. Permeable Underlayment: Permeable breather type underlayment membrane: SLOPESHEILD

PLUS as manufactured by VaproShield (note taped joints & fastener gasket requirement).

F. Synthetic Underlayment: Low-perm film used as substitute. Manufactured in large sheets to

minimize seams. Provide RoofTopGuard II, TriFlex 30 or equal

G. Solder: Lead solder containing 50% tin and 50% lead in accordance with ASTM B32 – 08 (or latest
edition) or lead-free solder. Flux: Felder ZD-Pro or equal.

H. Sealants:
1. Joint Sealant: DOW 795, or other documented pH neutral sealant
2. Backer rod shall be extruded polyethylene foam as DOW ETHAFOAM SB or equal.

I. Snow Guards: S-5! or consult manufacturer.

2.04 PANEL & FLASHING FABRICATION

A. General: Custom fabricate sheet metal panels to comply with details shown and recommendations
in SMACNA’s “Architectural Sheet Metal Manual” and RHEINZINK Division 7 Binder; Latest Edition
that apply to the design, dimensions (pan width and depth), geometry, metal thickness, and other
characteristics of installation indicated. Shop fabricates sheet metal wall panels and accessories at
the shop to the greatest extent possible.

1. Standing-Seam Roofing Panels: Form standing-seam pans from continuous metal sheets,
with male and female dimensions to manufacturer’s specifications.

2. Provide backside coated zinc or other permanent separation materials on concealed panel
or flashing surfaces where panels or flashings would otherwise be in direct contact with
substrate materials that are non-compatible or could result in corrosion or deterioration of
either material or finishes.

A. Fabricate sheet metal roofing panels to allow for expansion in running work sufficient to prevent
leakage, damage, and deterioration of the Work. Form exposed sheet metal work to fit substrates
without excessive oil canning, buckling, and tool marks, true to line and levels indicated, and with
exposed edges folded back to form hems.

1. Form and fabricate sheets, seams, strips, cleats, edge treatments, integral flashing, and
other components of metal roofing to profiles, patterns, and drainage arrangements shown
and as required to resist Water infiltration without excessive use of sealants (dry Joints)
while also allowing any water infiltration behind the roof panels to weep out.

B. Expansion Provisions: Where lapped or bayonet-type expansion provisions in the Work cannot be
used, form expansion joints of intermeshing hooked flanges, not less than 1 inch deep, and filled
with non-acidic sealant (concealed within joints) if determined to be necessary for weather-tight
detail (dry joints are often acceptable).

C. Sealant Joints: Where movable, non-expansion-type joints are indicated or required to produce
weather tight seams, form metal to provide for proper installation of elastomeric sealant in
compliance with SMACNA standards. In general, panel joints are intended to be dry, sealant-free,
to facilitate air movement and drying behind the roof panels.

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 6 of 9
PART 3 – EXECUTION

3.01 INSPECTION

A. Contractor shall inspect all surfaces, areas and other contingent construction in or to which his
work is to be installed and insure himself that they are in proper condition to receive the work to be
performed under this Section.

A. Verify that sheathing surfaces are sound, dry, properly secured and that provision has been made
for flashings, anchorage, and all other interface items attaching to or penetrating through the Work
of this Section.

B. To the greatest extent possible, Contractor and Installer shall inspect roof deck before roof
underlayment is applied. Installer shall notify the Contractor of any deck, penetration, or other
substrate condition requiring corrective action.

3.02 PREPARATION

A. Verify field dimensions before fabrication. Notify Architect of any discrepancies between field
measurements and dimensions indicated in Construction Documents.

B. Place [permeable, synthetic, waterproof] underlayment membrane and venting mat on substrate
surfaces to receive metal panels; comply with manufacturer’s instructions.

1. Coordinate installation of underlayment with metal roofing, rain drainage work, flashing,
trim and construction of parapets, walls, and other adjoining work to provide a
weatherproof, secure and non-corrosive installation.

2. For underlayment end-laps and side-laps, see underlayment manufacturer’s instructions

for proper attachment, seaming, and termination recommendations.

3. Apply weather barrier underlayments parallel to the eave.

C. For loose-laid mechanically attached sheets, consult the architect for strategies preventing
moisture infiltration through fastener holes. Potential solutions include: applying sealant or self-
adhered gaskets to backside of clips.

3.03 FIELD FABRICATION

A. Form panels and flashings in shop to greatest extent possible. Field modify only as necessary.

B. Ensure material temperature has moderated above 48 degrees F. prior to field fabrication.

C. Cut prefabricated zinc panels, and flashing with smooth (non-serrated) blade shears and snips.
Bend zinc so that there are properly sized radius bends. Inspect initial panel and flashing bends to
ensure material cracking has not occurred.

D. Form rounded cuts and notches as made by MASC notching tool and demonstrated during zinc
manufacturer fabrication training. Rounded cuts & notches are also possible by cutting to a
predrilled hole.

3.04 INSTALLATION

A. Manufacturer’s Recommendations: Except as otherwise shown or specified, comply with

Recommendations and instructions of manufacturer of sheet metal being fabricated and installed.

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 7 of 9
 1. Do not install in inclement weather
2. Do not install over a damp substrate
3. Do not install when inclement weather is threatening.
4. If covering of zinc panels is required, provide free air flow around the zinc material to
manufacturer’s requirement to prevent white rust.

B. Install work to be truly straight and square or conform to curvilinear geometry indicated on
drawings.

1. Fabricate and install work with lines and corners of exposed units true and accurate.
2. Form exposed faces free of buckles, excessive waves, and avoidable tool marks
considering temper and reflectivity of metal.
3. Shim and align panel units within installed tolerance of ¼ inch in 20’ –0”
4. All seams shall be of uniform appearance and dimensions, straight and level with
minimum exposure of solder and sealant.
5. Except as otherwise shown, fold back sheet metal to form a hem on concealed side of
exposed edges.
6. Form all seams to be weatherproof, leaving room for expansion and contraction with
specified and required tolerances.
7. Comply with RHEINZINK Division 7 Binder; latest edition and SMACNA Architectural
Sheet Metal Manual; latest edition, for flashings and sheet metal work.

C. Conceal fasteners and expansion provision where possible in exposed work, and locate so as to
minimize possibility of leakage. Cover and seal fasteners and anchors as required for a tight
installation.

D. To avoid material tearing, provide cuts with rounded notching tool or cut to pre-drilled hole. Only
use smooth edge (non-serrated) shears and snips for zinc cutting.

E. Provide indirect attachment of exposed zinc with concealed “keeper” whenever possible. Avoid
exposed and direct fastening especially at lap locations to allow movement.

F. Provide work as indicated on approved shop drawings

1. Form and fabricate sheets, seams, strips, cleats, edge treatments, integral flashings, and
other components of metal wall cladding to profiles, patterns, and drainage arrangements
shown and as required for water shedding construction. Ensure that all shop & field
fabricated bends have an acceptable “rounded” or radius bend. NO SHARP BREAKS.

G. Separate non-compatible materials with a rubberized asphalt underlayment.

H. Install work to meet specified performance requirements.

3.05 CLEANING AND PROTECTION

A. Remove protective film (if any) from exposed surfaces of metal roofing promptly upon installation
(or prior if film covers any concealed seam areas) with care to avoid damage to finish and in
accordance with manufacturer’s recommendations.

B. Clean exposed metal surfaces of substances that would interfere with uniform oxidation and
weathering and as recommended by panel manufacturer and maintain in a clean condition during
construction. Never apply cleaner directly to zinc surface.

C. Ensure that cleaning by other trades working in proximity to zinc installation is in accordance with
the recommendations of the zinc manufacturer.

D. Damaged units: Replace panels and other components of the work that have been damaged or
have deteriorated beyond successful repair by means of finish touch-up or similar minor repair.

E. For more complete instructions, please refer to RHEINZINK cleaning recommendations.

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 8 of 9
3.06 RECYCLING

A. Collect all zinc drop-offs (scrap) and return to local scrap metal recycling facility for current market
cash return.

3.07 CLEAN-UP

A. During the progress of the work, keep premises clear of debris resulting from this operations and
remove surplus and waste materials from the site as soon as possible.

B. Upon completion of the work, Contractor shall remove from the site all equipment and materials
used on the work as well as any debris resulting from the operations.

-END OF SECTION-

STANDING SEAM METAL ROOFING PANELS Section 07 61 13

September 8, 2024 Page 9 of 9