OPERATOR’S

MANUAL

Model C706
Soft Serve Freezer

Original Operating Instructions

056436-M February 2003 (Original Publication)

(Updated 8/18/2020)
Complete this page for quick reference when service is required:

Taylor distributor: __________________________________________________________

Address:_________________________________________________________________

Phone: __________________________________________________________________

Service: _________________________________________________________________

Parts: ___________________________________________________________________

Date of Installation: ________________________________________________________

Information found on the data label:

Model Number: ___________________________________________________________

Serial Number: ____________________________________________________________

Electrical Specs: Voltage__________________ Cycle__________

Phase__________________________________

Maximum Fuse Size: ______________________________________________________ A

Minimum Wire Ampacity: ___________________________________________________ A

Note: Continuing research results in steady improvements; therefore, information in this manual is subject to change
without notice.
Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be
the original set of instructions.

© 2003 Taylor Company

056436-M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be
a violation of copyright law of the United States of America and other countries, could result in the awarding of
statutory damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal
penalties. All rights reserved.

Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
 Table of Contents
Section 1: To the Installer
Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Air-Cooled Machines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Water Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Beater Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Section 2: To the Operator
Section 3: Safety
Section 4: Operator Parts Identification
Model C706 Single Spout Door and Beater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
X57029-XX Pump A.—Mix Simplified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Section 5: User Interface
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
MIX REF Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
STANDBY Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
WASH Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
AUTO Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
PUMP Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Beater Motor RESET Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Air/Mix Pump Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Adjustable Draw Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Optional Feed Tube (Backup Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

056436-M i
Table of Contents

Section 6: Operating Procedures

Prior to Setup (Freezers with Topping Pumps Only) . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Mix Hopper Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Draining Product from Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Manual Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Section 7: Operator’s Checklist
During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Regular Maintenance Checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Air/Mix Pump Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Section 8: Troubleshooting Guide
Section 9: Parts Replacement Schedule
Section 10: Limited Warranty on Equipment
Section 11: Limited Warranty on Parts

ii 056436-M
Section 1 To the Installer

The following information has been included in the

manual as safety and regulatory guidelines. For complete
installation instructions, see the Installation Checklist.
WARNING! This machine has many sharp
edges that can cause severe injuries.
Installer Safety
All repairs must be performed by an authorized Taylor 1
service technician.
Site Preparation
Review the area where the machine will be installed
before uncrating the machine. Make sure that all possible
IMPORTANT! In all areas of the world, hazards to the user and the equipment have been
machines should be installed in accordance with existing addressed.
local codes. Please contact your local authorities if you
have any questions.
Care should be taken to ensure that all basic safety
WARNING! Only install this machine in a
practices are followed during the installation and
location where its use and maintenance is restricted to
servicing activities related to the installation and service
trained personnel. Failure to comply may result in
of Taylor® machines.
personal injury.
• Only Taylor service personnel should perform
installation, maintenance, and repairs on Taylor
machines.
• Authorized service personnel should consult Air-Cooled Machines
OSHA Standard 29CFRI910.147 or the Do not obstruct air intake and discharge openings:
applicable code of the local area for the industry The model C706 air-cooled machine requires a minimum
standards on lockout/tagout procedures before of 6 in. (152 mm) of clearance on both sides and 0 in.
beginning any installation or repairs. (0.0 mm) in the rear of the machine. This allows for
• Authorized service personnel must ensure that adequate air flow across the condenser(s). Failure to
the proper personal protective equipment (PPE) allow adequate clearance can reduce the refrigeration
is available and worn when required during capacity of the freezer and possibly cause permanent
installation and service. damage to the compressor.
• Authorized service personnel must remove all For Indoor Use Only: This machine is designed to
metal jewelry, rings, and watches before operate indoors, under normal ambient temperatures of
working on electrical equipment. 70°F to 75°F (21°C to 24°C). The freezer has
successfully performed in high ambient temperatures of
104°F (40°C) at reduced capacities.

DANGER! The main power supply(s) to the

machine must be disconnected prior to performing any WARNING! This machine must NOT be
installation, maintenance, or repairs. Failure to follow this installed in an area where a water jet or hose can be
instruction may result in personal injury or death from used. NEVER use a water jet or hose to rinse or clean
electrical shock or hazardous moving parts, as well as the machine. Failure to follow this instruction may result
poor performance or damage to the machine. in electrocution.

To the Installer Model C706 1-1

 TO THE INSTALLER

Electrical Connections

CAUTION! This machine must be installed on

a level surface to avoid the hazard of tipping. Extreme IMPORTANT! In the United States, this
care should be taken in moving this machine for any machine is intended to be installed in accordance with
reason. Two or more persons are required to safely move the National Electrical Code (NEC), ANSI/NFPA 701987.
this machine. Failure to comply may result in personal The purpose of the NEC code is the practical
1 injury or machine damage. safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety.

Water Connections In all other areas of the world, the machine should be
installed in accordance with the existing local codes.
(Water-Cooled Machines Only)
Please contact your local authorities if you have any
An adequate cold water supply must be provided with a
questions.
hand shutoff valve. On the underside rear of the base
Each machine requires one power supply for each data
pan, two 3/8 in. iron pipe size (IPS) water connections for
label on the machine. Check the data label(s) on the
inlet and outlet have been provided for easy hookup.
machine for branch circuit overcurrent protection or fuse,
Permanently connect the machine using 1/2 in. (12.7
circuit ampacity, and other electrical specifications.
mm) inside diameter water lines. Flexible water lines are
recommended if local codes permit. Depending on local See the wiring diagram provided inside the electrical box
water conditions, it may be advisable to install a water for proper power connections.
strainer to prevent foreign substances from clogging the
automatic water valve. There will be only one water-in
and one water-out connection. Do not install a hand FOLLOW YOUR LOCAL ELECTRICAL CODES.
shutoff valve on the water-out line! Water should always
flow in this order: first, through the automatic water valve;
second, through the condenser; third, through the outlet
fitting to an open trap drain.

WARNING! This machine must be properly

grounded. Failure to do so can result in severe personal
IMPORTANT! A backflow prevention device is injury from electrical shock.
required on the incoming water connection side. Please
see the applicable national, state, and local codes for
determining the proper configuration. Water pressure to
the unit must not exceed 150 psi (1034 kPa). WARNING! DO NOT operate this machine
with fuses larger than specified on the machine data
label. Failure to follow this instruction may result in
electrocution or damage to the machine.

1-2 Model C706 To the Installer

 TO THE INSTALLER

Refrigerant

IMPORTANT! This machine is provided with an

CAUTION! This machine contains fluorinated
equipotential grounding lug that is to be properly
greenhouse gases (F-Gas) to provide refrigeration using
attached to the rear of the frame by the authorized
a hermetically sealed circuit or within foam insulation.
installer. The installation location is marked by the
This machine’s type of gas, quantity, Global Warming
equipotential bonding symbol (5021 of IEC 60417-1) on
Potential (GWP) and CO2 tonnes equivalent information
1
both the removable panel and the machine’s frame.
is recorded on the machine’s data label. The refrigerant
Stationary machines which are not equipped with a
used is generally considered nontoxic and
power cord and a plug or other device to disconnect the
nonflammable. However any gas under pressure is
machine from the power source must have an all-pole
potentially hazardous and must be handled with caution.
disconnecting device with a contact gap of at least
0.125 in. (3 mm) installed in the external installation. NEVER fill any refrigerant cylinder completely with liquid.
Filling the cylinder to approximately 80% will allow for
Machines that are permanently connected to fixed wiring
normal expansion.
and for which leakage currents may exceed 10 mA,
particularly when disconnected or not used for long
periods, or during initial installation, shall have protective
devices to protect against the leakage of current, such as CAUTION! Use only approved refrigerant
a GFI, installed by the authorized personnel to the local listed on the machine's data label or authorized through a
codes. manufacturer's technical bulletin. The use of any other
Supply cords used with this machine shall be oil- refrigerant may expose users and operators to
resistant, sheathed flexible cable not lighter than ordinary unexpected safety hazards.
polychloroprene or other equivalent synthetic elastomer-
sheathed cord (code designation 60245 IEC 57) installed
with the proper cord anchorage to relieve conductors
WARNING! Refrigerant liquid sprayed onto the
from strain, including twisting, at the terminals and
skin may cause serious damage to tissue. Keep eyes
protect the insulation of the conductors from abrasion.
and skin protected. If refrigerant burns should occur,
flush the area immediately with cold water. If burns are
Beater Rotation severe, apply ice packs and contact a physician
immediately.

NOTICE! Beater rotation must be clockwise as

viewed looking into the freezing cylinder.
IMPORTANT! Refrigerants and their
To correct the rotation on a three-phase machine, associated lubricants may be extremely moisture
interchange any two incoming power supply lines at the absorbent. When opening a refrigeration system, the
freezer main terminal block only. To correct rotation on a maximum time the system is open must not exceed 15
single-phase machine, exchange leads inside the beater minutes. Cap all open tubing to prevent humid air or
motor. (Follow the diagram printed on the motor.) water from being absorbed by the oil.
Electrical connections are made directly to the terminal
block provided in the main control box located behind the
service panel.
It is recommended that beater rotation adjustment be
performed by an authorized Taylor service technician.

To the Installer Model C706 1-3

 TO THE INSTALLER

Notes:

1-4 Model C706 To the Installer

Section 2 To the Operator

The Model C706 has been carefully engineered and other similar end-of-life legislation in effect after August
manufactured to give you dependable operation. 13, 2005. Therefore, it must be collected separately after
This machine, when properly operated and cared for, will its use is completed and cannot be disposed as unsorted
produce a consistent quality product. Like all mechanical municipal waste.
products, it requires cleaning and maintenance. A The user is responsible for delivering the machine to the
minimum amount of care and attention is necessary if the appropriate collection facility, as specified by your local
operating procedures outlined in this manual are code.
followed. For additional information regarding applicable local
disposal laws, please contact the municipal waste facility
and/or local authorized Taylor distributor.
2
IMPORTANT! This manual should be read The user is responsible for returning the product to the
before operating or performing any maintenance on your appropriate collection facility, as specified by your local
machine. code. For additional information regarding applicable
local laws, please contact the municipal facility and/or
local distributor.
Your Taylor freezer will not eventually compensate for
and correct any errors during the setup or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that personnel responsible for the
equipment’s operation, both assembly and disassembly,
go through these procedures together in order to be
properly trained and to make sure that no confusion
exists.
If you should require technical assistance, please contact
an authorized Taylor distributor.
Note: Your Taylor warranty is valid only if the parts are
authorized Taylor parts, purchased from the local
authorized Taylor distributor, and only if all required
service work is provided by an authorized Taylor service
technician. Taylor reserves the right to deny warranty
claims on machines or parts if parts not approved by
Taylor or incorrect refrigerant were installed in the
machine, system modifications were performed beyond
factory recommendations, or it is determined that the
failure was caused by abuse, misuse, neglect, or failure
to follow all operating instructions. For full details of your
Taylor Warranty, please see the Limited Warranty section
in this manual.

IMPORTANT! If the crossed-out wheeled-bin

symbol is affixed to this machine, it signifies that this
machine is compliant with the EU Directives as well as

To the Operator Model C706 2-1

 TO THE OPERATOR

Compressor Warranty Disclaimer It should also be noted that Taylor does not warrant the
refrigerant used in its equipment. For example, if the
The refrigeration compressor(s) on this machine are refrigerant is lost during the course of ordinary service to
warranted for the term stated in the Limited Warranty this machine, Taylor has no obligation to either supply or
section in this manual. However, due to the Montreal provide replacement refrigerant either at billable or
Protocol and the U.S. Clean Air Act Amendments of non-billable terms. Taylor will recommend a suitable
1990, many new refrigerants are being tested and replacement if the original refrigerant is banned,
developed, thus seeking their way into the service obsoleted, or no longer available during the five year
industry. Some of these new refrigerants are being Taylor warranty of the compressor.
advertised as drop-in replacements for numerous
Taylor will continue to monitor the industry and test new
applications. It should be noted that in the event of
alternates as they are being developed. Should a new
2 ordinary service to this machine's refrigeration system,
only the refrigerant specified on the affixed data label
alternate prove, through our testing, that it would be
accepted as a drop-in replacement, then the above
should be used. The unauthorized use of alternate
disclaimer would become null and void. To find out the
refrigerants will void your Taylor compressor warranty. It
current status of an alternate refrigerant as it relates to
is the machine owner's responsibility to make this fact
your compressor warranty, call the local Taylor distributor
known to any technician they employ.
or the Taylor factory. Be prepared to provide the model/
serial number of the machine in question.

2-2 Model C706 To the Operator

Section 3 Safety

We at Taylor Company are concerned about the safety of

the operator when they come in contact with the freezer
and its parts. Taylor has gone to extreme efforts to design WARNING! This machine must NOT be
and manufacture built-in safety features to protect both installed in an area where a water jet or hose can be
the operator and the service technician. As an example, used. NEVER use a water jet or hose to rinse or clean
warning labels have been attached to the freezer to the machine. Failure to follow this instruction may result
further point out safety precautions. in electrocution.

DANGER! Failure to adhere to the following WARNING! Avoid injury.

safety precautions may result in severe personal injury or • DO NOT operate the machine unless it is prop-
death. Failure to comply with these warnings may also erly grounded.
damage the machine and/or its components. Such • DO NOT operate machine with fuses larger 3
damage may require component replacement and than specified on the data label.
service repair expenses. • All repairs must be performed by a Taylor ser-
vice technician.
• The main power supplies to machine must be
disconnected prior to performing repairs.
NOTICE! DO NOT operate this machine
• For Cord-Connected Machines: Only Taylor
without reading this manual. Failure to follow these
service technicians or licensed electricians may
instructions may result in machine damage, poor
install a plug or replacement cord on the
dispenser performance, health hazards, or personal
machine.
injury.
• Stationary machine which are not equipped with
a power cord and a plug or another device to
disconnect the machine from the power source
IMPORTANT! This machine is to be used only must have an all-pole disconnecting device with
by trained personnel. It is not intended for use, cleaning, a contact gap of at least 0.125 in. (3 mm)
or maintenance by children or people with reduced installed in the external installation.
physical, sensory, or mental capabilities or lack of • Machines that are permanently connected to
experience and knowledge,, unless given supervision or fixed wiring and for which leakage currents may
instruction concerning the use of the machine by a exceed 10 mA, particularly when disconnected
person responsible for their safety. Children should be or not used for long periods, or during initial
supervised to ensure that they do not play with the installation, shall have protective devices to pro-
machine. tect against the leakage of current, such as a
GFI, installed by the authorized personnel to the
local codes.
• Supply cords used with this machine shall be
IMPORTANT! An equipotential grounding lug is oil-resistant, sheathed flexible cable not lighter
provided with this machine. Some countries require the than ordinary polychloroprene or other equiva-
grounding lug to be properly attached to the rear of the lent synthetic elastomer-sheathed cord (code
frame by the authorized installer. The installation location designation 60245 IEC 57) installed with the
is marked by the equipotential bonding symbol (5021 of proper cord anchorage to relieve conductors
IEC 60417-1) on both the removable panel and the from strain, including twisting, at the terminals
machine's frame. and protect the insulation of the conductors
from abrasion.

Safety Model C706 3-1

 SAFETY

• If the supply cord is damaged, it must be

replaced by the manufacturer, service agent, or
a similarly qualified person, in order to avoid a
CAUTION! This machine must be placed on a
hazard.
level surface. Failure to comply may result in personal
• Secure the supply cord ground lead to the
injury or machine damage.
machine in a location where if the cord is pulled,
the main power leads will become taut before
the ground lead can break loose.
Failure to follow these instructions may result in WARNING! Only install this machine in a
electrocution. Contact your local authorized Taylor location where its use and maintenance is restricted to
distributor for service. trained personnel. Failure to comply may result in
personal injury.

WARNING! Avoid injury.

3 • DO NOT allow untrained personnel to operate
NOTICE! Cleaning and sanitizing schedules
are governed by your federal, state or local regulatory
this machine. agencies and must be followed accordingly. Please see
• DO NOT put objects or fingers in the door spout. the cleaning section of the manual for the proper
• DO NOT operate the machine unless all service procedure to clean this machine.
panels and access doors are fastened with
screws.
• DO NOT remove the machine door or beater
assembly unless the control switches are in the CAUTION! This machine is designed to
OFF position. maintain product temperature under 41°F (5°C). Any
product being added to this machine must be below 41°F
(5°C). Failure to follow this instruction may result in
WARNING! This machine has many sharp health hazards and poor machine performance.
edges that can cause severe injuries. Do not obstruct air intake and discharge openings:
• DO NOT put objects or fingers in the door A minimum of 6 in. (152 mm) air space is required on
spout. This may contaminate the product and both sides and 0 in. (0 mm) on the rear. Failure to follow
cause severe personal injury from blade this instruction may cause poor freezer performance and
contact. damage to the machine.
• USE EXTREME CAUTION when removing the
For Indoor Use Only: This machine is designed to
beater assembly. The scraper blades are very
operate indoors, under normal ambient temperatures of
sharp.
70°F to 75°F (21° to 24°C). The machine has
• USE EXTREME CAUTION when handling the
successfully performed in high ambient temperatures of
cup/cone dispenser (if supplied with machine).
up to 104°F (40°C) at reduced capacities.
Two people are required to handle the cup/cone
dispenser. The appropriate type of protective
gloves must be worn and the mounting holes
CAUTION! DO NOT run the machine without
must NOT be used to lift or hold the dispenser.
product. Failure to follow this instruction can result in
Failure to follow these instructions can result in personal damage to the machine.
injury or damage to the machine.
Noise Level: Airborne noise emission does not exceed
78 dB(A) when measured at a distance of 39 in. (1.0 m)
from the surface of the machine and at a height of 63 in.
(1.6 m) from the floor.

3-2 Model C706 Safety

Section 4 Operator Parts Identification

15
2 12
16
11 17
3
18

9
5

6
4

10 14 13
7 8

Figure 4-1

Item Description Part No. Item Description Part No.

1 Kit A.-Cover-Hopper X65368-SP 10 Panel A.-Side-Right*AC X64151

2 Pan-Drip 11-5/8” Long 027503 11 Panel-Rear 056077

3 Pin-Retaining-Hopper 043934 12 Pump A.-Mix Simplified S.S. X57029-14

Cover (See page 4-3)

4 Panel-Side-Left 066722-SP2 13 Panel A.-Side-Right *TAD X81369-SER

(Optional)
5 Stud-Nose Cone 055987
14 Guard-Fan 028534-1
6 Shield-Splash 049203
*15 Orifice 022465-100
7 Tray-Drip *Black 056858
*16 O-ring-3/8 OD X 0.070W 016137
8 Panel-Front-Lower 058942
*17 O-ring-.643 OD X 0.077W 018572
9 Panel A.-Front-Upper X58950
*18 Tube A.-Feed-SS-5/32 Hole X29429-2
*Optional feed tube.

Operator Parts Identification Model C706 4-1

 OPERATOR PARTS IDENTIFICATION

Model C706 Single Spout Door and Beater Assembly

17

15
18

14

2 8

6
9
7
16

4 3

13 14
4 12

1 5
10 11
Figure 4-2

Item Description Part No. Item Description Part No.

1 Door A. X87683 9 O-ring -7/8 OD X 0.103 W 014402

2 Handle A.-Draw-Welded X56246 10 Nut-Stud Black-3.25 Long 058765

3 Screw-Adjustment-5/16-24 056332 11 Nut-Stud Black-2.56 Long 058764

4 O-ring-1/4 OD X 0.070W 50 015872 12 Gasket-Door HT 4" DBL 048926

5 Pin-Handle-S.S. 055819 13 Baffle -Threadess Molded 087708

6 Plug-Prime 028805 14 Kit A.-Beater Front Shoe X50350

7 O-ring-3/8 OD X .070W 016137 15 Beater A.-3.4 qt. - 1 Pin X46231

8 Valve A.-Draw X56072 16 Blade-Scraper-Plastic 8-1/8L 084350

17 Shaft-Beater 056078

18 Seal-Drive Shaft 032560

4-2 Model C706 Operator Parts Identification

 OPERATOR PARTS IDENTIFICATION

X57029-XX Pump A.—Mix Simplified

7 4
9
6 10c 10d 14
11
12
3
2

10b
5
8
13 10a
10
8
4 1

Figure 4-3

Item Description Part No. Item Description Part No.

4
1-7 Pump A.-Mix Simplified S.S. X57029-14 10 Shaft A.-Drive-Mix Pump-Hopper X41947

1 Cylinder-Pump Hopper Soft Serve 057943 10a Crank-Drive-Hopper Mix Pump 039235

2 Pin-Retaining X55450 10b Shaft-Drive-Mix Pump-Hopper 041948

3 Piston-Pump-Simplified 053526 10c O-ring-1-3/4 OD X 008904

0.139W-Crank *(25 to Bag)*
4 O-ring-2-1/8 OD X 020051
0.139W-#225 *(50 to Bag)* 10d O-ring 1/2 ID X 0.139W-Shaft 048632
*(25 to Bag)*
5 Cap-Valve Body SS 056874-14
11 Clip-Retainer-Mix Pump 044641
6 Gasket-Simplified Pump Valve 086097
12 Tube A.-Feed-Hopper S.S. X56521
7 Adaptor-Mix Inlet-SS-Red 054825
13 Ring-Check-Feed-Tube 056524
8 O-ring-11/16ODX0.103W-Red 016132
*50 To Bag* 14 Sleeve A.-Mix Pump *HT X44761

9 Pin-Cotter-Hairpin-1/8DIA 044731

Operator Parts Identification Model C706 4-3

 OPERATOR PARTS IDENTIFICATION

Accessories

1 6

2
7

4
5

10

9 8

Figure 4-4

Item Description Item Description

1 Tool-O-ring Removal *6 Sanitizer Stera-Sheen® (Qty 100 2 oz. Packets)

2 Brush-Rear·BRG·1 in. DX2 in. 7 Pail-10 qt.
3 Brush-Double·Ended 8 Brush-End-Door-Spout
4 Brush-Draw·Valve·1 in. ODX2” 9 Brush-Set·LVB
5 Brush-Mix·Pump·Body-3”X7” 10 Brush-Pump·Spout

*Item 6: A sample of Stera-Sheen® is shipped with new

equipment. To order additional sanitizer, use the part number
listed.

4-4 Model C706 Operator Parts Identification

Section 5 User Interface

C706

5 1 2

3 6 7
4

8 9

12 11
10

Figure 5-1

Item Description Item Description

1 MIX LOW Indicator Light 7 PUMP Key

2 MIX OUT Indicator Light 8 RESET Button-Beater Motor

3 MIX REF Key 9 Reset Button -Pump

4 STANDBY Key 10 Power Switch (Toggle)

5 WASH Key 11 Hopper Temp. Indicator

6 AUTO Key *12 Optional Flavor Burst Jack

*Not available on all machines.

User Interface Model C706 5-1

 USER INTERFACE

Symbol Definitions MIX REF Key

To better communicate in the international arena, When the MIX REF key is pressed, the indicator light
symbols have replaced words on many of our operator comes on and the mix hopper refrigeration system is
switches, function, and fault indicators. Your Taylor operating. The MIX REF function cannot be canceled
machine is designed with these International symbols. unless the Auto or Standby modes are canceled first.
The following chart identifies the symbol definitions:
STANDBY Key
The separate hopper refrigeration (SHR) system and the
= OFF
cylinder temperature retention (CTR) system are
standard features. The SHR system uses a separate
= ON small refrigeration system to maintain the mix in the
hopper below 40°F (4.4°C) to ensure bacteria control.
The CTR system works with the SHR system to maintain
= MIX LOW
a good quality product. During long no sale periods, it is
necessary to warm the product in the freezing cylinder to
= MIX OUT approximately 35°F to 40°F (1.7°C to 4.4°C) to prevent
overbeating and product breakdown.
= MIX REF To activate the SHR system and CTR system, press the
STANDBY key. Remove the air orifice and place the feed
= STANDBY tube (end without the hole) into the mix inlet hole.
When the STANDBY key is pressed, the indicator light
5 = WASH comes on, indicating the CTR system has been
activated. In the Standby mode, the Wash and Auto
functions are automatically canceled. The Mix Ref
= AUTO
function is automatically locked in to maintain the mix in
the hopper.
= PUMP To resume normal operation, press the AUTO key. When
the machine cycles off, the product in the freezing
Power Switch cylinder is at serving viscosity. At this time, place the feed
When placed in the ON position, the power switch allows tube (end with the hole) into the mix inlet hole and install
Softech™ control panel operation. the air orifice.

Indicator Lights WASH Key

When the MIX LOW indicator light flashes, the mix tank When the WASH key is pressed, the indicator light
has a low supply of mix and should be refilled as soon as comes on showing that the beater motor is operating.
possible. When the MIX OUT indicator light begins to The Standby or Auto modes must be canceled first to
flash, the mix tank has been almost completely activate the Wash mode.
exhausted and has an insufficient supply of mix to
operate the freezer. At this time, the Standby and Auto
modes are locked out and the freezer shuts down. To
initiate the refrigeration system, add mix to the tank and
press the AUTO key. The freezer will automatically begin
operation.

5-2 Model C706 User Interface

 USER INTERFACE

AUTO Key Air/Mix Pump Reset Button

When the AUTO key is pressed, the indicator light shows The Reset button for the pump is located on the left side
that the main refrigeration system is activated. In the of the machine. This protects the pump from an overload
Auto mode, the Wash or Standby functions are condition. Should an overload occur, the reset
automatically canceled. The Mix Ref function is mechanism will trip. To reset the pump, press the Reset
automatically locked in to maintain the mix in the mix button firmly.
hopper.
Note: An indicating light illuminates and an audible Adjustable Draw Handle
tone sounds when a mode of operation has been The Model C706 features an adjustable draw handle to
pressed. To cancel any function, press the key again. provide the best portion control. The draw handle should
The indicator light and mode of operation will shutoff. be adjusted to provide a flow rate of 5 oz. to 7-1/2 oz. of
product per 10-seconds. To increase the flow rate, turn
PUMP Key the screw clockwise. To decrease the flow rate, turn the
When the PUMP key is pressed, the pump indicator light screw counterclockwise.
comes on indicating the air/mix pump will operate as 10354

required.

Beater Motor RESET Button

The RESET button is on the left side of the machine. A
reset mechanism protects the beater motor from an
overload condition. If an overload occurs, the reset
mechanism will trip. To reset the freezer, press the AUTO 5
key to cancel the cycle. Turn the power switch to the OFF
position. Press the RESET button firmly.

Figure 5-2
CAUTION! DO NOT use metal objects to press
the reset button. Failure to follow this instruction may
result in electrocution.

Turn the power switch to the ON position. Press the

WASH key and observe the freezer’s performance. Open
the side access panel. Make sure the beater motor is
turning the driveshaft in a clockwise direction (from the
operator end) without binding.
If the beater motor is turning properly, press the WASH
key to cancel the cycle. Press the AUTO key to resume
normal operation. If the freezer shuts down again,
contact a service technician.

User Interface Model C706 5-3

 USER INTERFACE

Optional Feed Tube (Backup Option) The feed tube serves two purposes. One end of the tube
has a hole in the side and the other end does not.
If the air/mix pump has become inoperable because of a
missing or damaged part, the operator can temporarily
operate the machine using the feed tube. The product Normal Operation
ejection rate will be slower when the feed tube is used
During normal operation, the end of the feed tube with
instead of the air/mix pump.
the hole in the side is placed into the mix inlet hole. Every
12160
time the draw handle is raised, new mix and air from the
hopper flow into the freezing cylinder. This keeps the
freezing cylinder properly loaded and maintains overrun.

4 1 Long No Sale Periods

3 2
During long no sale periods, the machine can be placed
in the Standby mode. This mode maintains product
temperatures below 40°F (4.4°C) in both the hopper and
the freezing cylinder and helps prevent overbeating and
product breakdown.
To place the machine in the Standby mode, press the
Figure 5-3 STANDBY key. Remove the air orifice. Lubricate the
O-rings located on the end of the feed tube without the
Item Description Part No. hole. Place that end of the tube into the mix inlet hole.
This prevents any mix from entering the freezing cylinder.
5 1 Orifice 022465-100
Note: The air orifice meters a certain amount of air into
2 O-ring-3/8” OD X 0.070 W 016137
the freezing cylinder. The air orifice maintains overrun
3 Tube A.-Feed-SS 5/32” Hole X29429-2 and allows enough mix to enter the freezing cylinder after
a draw.
4 O-ring-0.643 OD X 0.077 W 018572

5-4 Model C706 User Interface

Section 6 Operating Procedures

The C706 machine stores mix in a hopper. The mix is Assembly

pumped from the hopper into the freezing cylinder. The
Note: When lubricating parts, use an approved food
machine has a 3.4 qt. (3.2 L) capacity freezing cylinder
grade lubricant (example: Taylor Lube).
and a 20 qt. (18.9 L) mix hopper.
We begin our instructions at the point where we enter the
store in the morning and find the parts disassembled and WARNING! Make sure the power switch is in
laid out to air dry from the previous night’s cleaning. the OFF position. Failure to follow this instruction may
These opening procedures show you how to assemble result in severe personal injury from hazardous moving
these parts into the freezer, sanitize them, and prime the parts.
freezer with fresh mix in preparation to serve your first
portion.
1. Lubricate the groove and shaft portion that comes in
If you are disassembling the machine for the first time, or contact with the bearing on the beater driveshaft. Slide
need information to get to this starting point in our the seal over the shaft and groove until it snaps into
instructions, see “Disassembly” on page 6-11 and start place. Do not lubricate the hex end of the driveshaft.
there.
Fill the inside portion of the seal with 1/4 in. (6.4 mm)
more lubricant and lubricate the flat side of the seal
Prior to Setup (Freezers with Topping that fits onto the rear shell bearing.
Pumps Only)
11078

Remove the stainless steel syrup jar with the topping

pump from the syrup rail. Check the water level in the
well. Make sure the water is filled to the indicating mark on
the inside wall 16 oz. (473 mL). Check the water daily.
Apply the appropriate
Place the heater switch in the ON position. The heating
process takes approximately 1-1/4 hours.
Taylor approved food safe lubricant.
6
Prepare a pail of an approved 100 PPM sanitizing solution
(examples: Kay-5® or Stera-Sheen®). Use warm water
and follow the manufacturer’s specifications.
Sanitize the pump by placing the entire assembly in the
solution. Pump the solution through the pump until it is
Figure 6-1
sanitized.
Fill the heated and the room-temperature syrup jars
with toppings. Place the topping pump in the heated
syrup jar. Sanitize the ladle and place it in the
room- temperature jar.

Operating Procedures Model C706 6-1

 OPERATING PROCEDURES

2. Insert the driveshaft into the freezing cylinder (hex 4. Place the rear scraper blade over the rear holding pin
end first) and into the rear shell bearing until the seal on the beater.
fits securely over the rear shell bearing. Engage the Note: The hole on the scraper blade must fit
hex end firmly in the drive coupling. Make sure the securely over the pin to prevent costly damage.
driveshaft fits into the drive coupling without binding.
11256

11230

Figure 6-4
Figure 6-2
5. Holding the rear blade on the beater, slide it halfway
3. Before installing the beater assembly, inspect the into the freezing cylinder. Install the front scraper
scraper blades for any signs of wear or damage. If a blade over the front holding pin.
scraper blade is nicked or worn, replace both blades.
6. Before installing the beater shoes, check them for
11529
any nicks, cracks, or signs of wear. If any defects are
present, replace the beater shoes.
7. If the beater shoes are in good condition, install

6 them.

11532

Figure 6-3

Figure 6-5
8. Slide the beater assembly the rest of the way into the
freezing cylinder.
Make sure the beater assembly is in position over the
driveshaft. Turn the beater slightly to be certain it is
properly seated. When in position, the beater should
not protrude beyond the front of the freezing cylinder.

6-2 Model C706 Operating Procedures

 OPERATING PROCEDURES

9. Before assembling the freezer door, check the 12. Insert the prime plug into the hole in the top of the
following for any nicks, cracks, or signs of wear: door freezer door and push down.
bearing, door gasket, draw valve, O-rings, and all
sides of the door assembly, including the inside of the
draw-valve bore. Replace any damaged parts.
10. If the parts are in good condition, place the door
gasket into the groove on the back side of the freezer
door. Install the baffle by raising the round end while
engaging the lug into the door pocket. Lower the
round end to secure to the door. Do not lubricate the
gasket.

Figure 6-8
13. Slide the three O-rings into the grooves on the draw
valve and lubricate.
11294

Apply the appropriate

Taylor approved food safe lubricant.

Figure 6-6
11. Slide the two O-rings into the grooves on the prime
plug. Apply an even coat of Taylor Lube to the 6
O-rings and shaft.
11092

Figure 6-9
14. Insert the draw valve from the top until it reaches the
Apply the appropriate bottom.
Taylor approved food safe lubricant.
10523

Figure 6-7

Figure 6-10

Operating Procedures Model C706 6-3

 OPERATING PROCEDURES

15. Install the adjustable draw handle. Slide the fork over 18. Slide the rear drip pan into the hole in the side panel.
the bar in the slot of the draw valve. Secure it with the Slide the pump drip pan into the hole in the back
pivot pin. panel.
10357

Figure 6-11 Figure 6-13

Note: This machine features an adjustable draw
handle to provide the best portion control. The draw Mix Hopper Assembly
handle can be adjusted for different flow rates. See 1. Inspect the rubber and plastic pump parts. The
page 5-3 for more information on adjusting this O-rings, check rings, and gaskets must be in 100%
handle. good condition for the pump and machine to operate
16. Insert the baffle rod through the opening in the beater properly. They cannot work properly if nicks, cuts, or
and seat the door flush with the freezing cylinder. holes are present. Inspect the plastic pump parts for
With the door seated on the freezer studs, install the cracks, wear, and delamination of plastic. Replace
handscrews. Tighten them equally in a crisscross any worn or damaged parts immediately and discard
6 pattern to ensure the door is snug. the old parts.
17. Install the front drip tray and the splash shield under 2. Assemble the mix inlet assembly. Slide the O-ring
the door spout. into the groove of the valve body cap. Do not
lubricate the O-ring.
10504

15109

Figure 6-12
Figure 6-14

6-4 Model C706 Operating Procedures

 OPERATING PROCEDURES

3. Slide the pump valve gasket into the holes on the 6. Lightly lubricate the inside of the pump cylinder at the
cap. Do not lubricate the gasket. bottom with a paper thin layer of lubricant.
15110 15206

Apply the appropriate

Taylor approved food safe lubricant.

Figure 6-15 Figure 6-18

4. Insert the valve body cap into the hole in the mix inlet 7. Insert the piston into the bottom of the pump cylinder.
adapter. 15204

15111

Figure 6-19
Figure 6-16 8. Insert the mix inlet assembly into the pump cylinder.
5. Assemble the piston. Slide the red O-ring into the 15205

groove of the piston. Do not lubricate the O-ring.

15117

Figure 6-20

Figure 6-17

Operating Procedures Model C706 6-5

 OPERATING PROCEDURES

Note: The drive hole in the mix inlet adapter must be 11. Install one red O-ring on each end of the mix feed
visible through the drive hole opening in the pump tube and thoroughly lubricate.
cylinder, and the aligning notch located at the base of the 15116

adapter must be positioned in the notch at the bottom of

the pump cylinder.
Apply the appropriate
9. Secure the pump parts in position by sliding the Taylor approved food safe lubricant.

retaining pin through the cross holes at the bottom of

the pump cylinder.
15207

Figure 6-23
12. Lay the pump assembly, pump clip, mix feed tube,
and cotter pin in the bottom of the mix hopper for
sanitizing.
12308

Figure 6-21
Note: The head of the retaining pin should be facing
up with the pump correctly installed.
10. Assemble the feed tube assembly. Slide the valve
O-ring into the groove of the feed tube.
6 15115

Figure 6-24

Figure 6-22

6-6 Model C706 Operating Procedures

 OPERATING PROCEDURES

13. Slide the large black O-ring and the two smaller black Sanitizing
O-rings into the grooves on the driveshaft.
1. Prepare an approved 100 PPM sanitizing solution
Thoroughly lubricate the O-rings and shaft. (See
(examples: 2-1/2 gal. [9.5 L] of Kay-5® or 2 gal.
Figure 6-25.) Do not lubricate the hex end of the
shaft. [7.6 L] of Stera-Sheen®). Use warm water and follow
the manufacturer’s instructions.
15009

2. Pour the sanitizing solution over all the parts in the

bottom of the mix hopper and allow it to flow into the
Apply the appropriate freezing cylinder.
Taylor approved food safe lubricant.

12029

Figure 6-25
14. Install the hex end of the driveshaft into the drive hub
at the rear wall of the mix hopper. (See Figure 6-26.)
12012

Figure 6-27
Note: You have just sanitized the mix hopper and
parts; therefore, make sure your hands are clean and
sanitized before going on in these instructions.
3. While the solution is flowing into the freezing cylinder, 6
take particular care to brush-clean the mix level
sensing probe on the front wall and the bottom of the
hopper, the mix hopper, the mix inlet hole, the air/mix
pump, the pump clip, the mix feed tube, and the
locking clip.

Figure 6-26
Note: For ease in installing the pump, position the
ball crank of the driveshaft in the 3 o’clock position.

Operating Procedures Model C706 6-7

 OPERATING PROCEDURES

4. Install the pump assembly. To position the pump on 6. Press the WASH key. This causes the sanitizing
the drive hub at the rear of the mix hopper, align the solution in the freezing cylinder to agitate. Allow it to
drive hole in the piston with the drive crank of the agitate for 5 minutes.
driveshaft. Secure the pump in place by slipping the
pump clip over the collar of the pump, making sure 13110

the clip fits into the grooves in the collar.

12309

Figure 6-30
7. With an empty pail beneath the door spout, raise the
prime plug and press the PUMP key.
Figure 6-28
5. Place the power switch in the ON position.
13063

Figure 6-31

Figure 6-29

6-8 Model C706 Operating Procedures

 OPERATING PROCEDURES

8. When a steady stream of sanitizing solution flows 10. Lubricate the mix feed tube O-rings located on the
from the prime plug opening in the bottom of the end of the tube with the small hole on the side. Stand
freezer door, pull the draw handle down. Draw off all the mix feed tube in the corner of the mix hopper.
of the sanitizing solution. Place the locking clip in position on the outlet fitting of
the pump.
12334

Figure 6-32
9. Once the sanitizer stops flowing from the door spout, Figure 6-34
raise the draw handle. Press the WASH and PUMP
keys, canceling the beater motor and pump Priming
operation. 1. Place an empty pail beneath the door spout and
lower the draw handle. Make sure the prime plug is
still in the up position. Pour 2 gal. (7.6 L) of fresh mix
into the hopper and allow it to flow into the freezing
cylinder. This forces out any remaining sanitizing
solution. When full strength mix is flowing from the 6
door spout, raise the draw handle.
Note: Use only fresh mix when priming the freezer.
2. Once a steady stream of mix starts to flow from the
prime plug opening in the bottom of the freezer door,
push down the prime plug.

Figure 6-33
Important! The machine must not be placed in Auto
mode until all sanitizing solution has been removed
from the freezing cylinder and proper priming
procedures have been completed. Failure to follow
this instruction may result in damage to the freezing
cylinder.
Note: Make sure your hands are clean and
sanitized before continuing these instructions.

Figure 6-35

Operating Procedures Model C706 6-9

 OPERATING PROCEDURES

Important! Failure to remove all sanitizing solution may Closing Procedure

result in damage to the freezing cylinder.
To disassemble your machine, the following items are
3. When the mix stops bubbling down into the freezing needed:
cylinder, insert the mix feed tube. Remove the locking • Two cleaning pails
clip from the outlet fitting of the mix pump. Insert the • Sanitized stainless steel rerun can with lid
outlet end of the mix feed tube into the mix inlet hole • Necessary brushes (provided with freezer)
in the mix hopper. Place the inlet end of the mix feed • Cleaner
tube into the outlet fitting of the mix pump. Secure it • Single-service towels
with the locking clip.
12335
Draining Product from Freezing
Cylinder
1. Press the AUTO key, canceling compressor and
beater motor operation. Press the MIX REF key,
canceling the mix hopper refrigeration system.
2. Remove the hopper cover and take it to the sink for
cleaning.
3. If local health codes permit the use of rerun, place a
sanitized, NSF International approved stainless steel
rerun container beneath the door spout. Press the
WASH and PUMP keys. Lower the draw handle and
drain the remaining product from the freezing
Figure 6-36
cylinder and mix hopper. When the flow of product
4. Press the AUTO key. When the machine cycles off, stops, press the WASH and PUMP keys and close
the product is at serving viscosity. the draw valve. Place the sanitized lid on the rerun
container and place it in the walk-in cooler.
6 13112

Note: If local health codes do not permit the use of

rerun, the product must be discarded. Drain the product
into a pail and properly discard it.

ALWAYS FOLLOW LOCAL HEALTH CODES.

Figure 6-37
5. Fill the hopper with fresh mix. As the mix level comes
in contact with the mix level sensing probe on the
front wall of the hopper, the MIX LOW indicator light
will shutoff.
Note: The MIX REF indicator light will come on,
showing the mix refrigeration system is maintaining
the mix in the hopper.
6. Place the mix hopper cover in position.

6-10 Model C706 Operating Procedures

 OPERATING PROCEDURES

Rinsing Disassembly
1. Pour 2 gal. (7.6 L) of cool, clean water into the mix
hopper. With the brushes provided, scrub the mix
hopper, the mix inlet hole, and the mix level sensing WARNING! Make sure the power switch is in
probe. the OFF position! Failure to follow this instruction may
2. With a pail beneath the door spout, raise the prime result in severe personal injury to fingers or hands from
plug and press the WASH key. hazardous moving parts.

3. When a steady stream of rinse water flows from the

prime plug opening in the bottom of the freezer door, 1. Remove the handscrews, freezer door, beater, beater
lower the draw handle. Drain all the rinse water from shoes, scraper blades, and driveshaft from the
the freezing cylinder. When the water stops flowing freezing cylinder. Take these parts to the sink for
from the door spout, raise the draw handle and press cleaning.
the WASH key, canceling the Wash mode. 2. Remove the driveshaft from the drive hub in the rear
Repeat this procedure until the rinse water being wall of the mix hopper.
drawn from the freezing cylinder is clear. 3. Remove the front drip tray and the splash shield.
4. Remove the assembled air/mix pump and take it to
the sink for further disassembly and cleaning. Manual Brush Cleaning
These procedures must be completed according to the
Cleaning frequency specified by your federal, state, or local
1. Prepare an approved 100 PPM cleaning solution regulatory agencies. Please consult your governing local
(examples: 2-1/2 gal. [9.5L] of Kay-5® or 2 gal. [7.6 L] code to determine the maximum number of days allowed
of Stera-Sheen®). Use warm water and follow the between brush clean cycles.
manufacturer’s specifications. Use the recommended cleaning procedure outlined in the
2. Push down the prime plug. Pour the cleaning solution manual or an alternate procedure used in conjunction
into the mix hopper. with a cleaning/sanitizing system that has been certified 6
by NSF International.
3. While the solution is flowing into the freezing cylinder,
brush clean the mix hopper, mix level sensing
probes, and the mix inlet hole. ALWAYS FOLLOW LOCAL HEALTH CODES.
4. Press the WASH key. This will agitate the cleaning
solution in the freezing cylinder.
5. Place an empty pail beneath the door spout and raise Make sure all brushes provided with the freezer are
the prime plug. available for brush cleaning.
6. When a steady stream of cleaning solution flows from 1. Prepare a sink with an approved cleaning solution
the prime plug opening in the bottom of the freezer (examples: Kay-5® or Stera-Sheen®). Use warm
door, lower the draw handle. Draw off all of the water and follow the manufacturer’s specifications. If
solution. another approved cleaner is used, dilute according to
7. Once the cleaning solution stops flowing from the label instructions.
door spout, raise the draw handle and press the Important! Follow label directions. Too strong of a
WASH key, canceling the Wash mode. solution can cause parts damage, while too mild of a
solution will not provide adequate cleaning. Make
sure all brushes provided with the freezer are
available for brush cleaning.

Operating Procedures Model C706 6-11

 OPERATING PROCEDURES

2. Remove the seal from the driveshaft. 6. Remove the rear drip pan from the side panel and
3. From the freezer door, remove the gasket, pivot pin, take it to the sink for cleaning.
adjustable draw handle, draw valve, and prime plug. Note: If the drip pan is filled with an excessive
Remove all O-rings. amount of mix, see the Troubleshooting Guide.
Note: To remove the O-rings, use a single-service 7. Thoroughly brush clean all disassembled parts in the
towel to grasp the O-ring. Apply pressure upward cleaning solution, making sure all lubricant and mix
until the O-ring pops out of its groove. With the other film is removed. Take particular care to brush clean
hand, push the top of the O-ring forward; it will roll out the hole for the draw valve in the freezer door. Place
of the groove and can be easily removed. If there is all cleaned parts on a clean, dry surface to air dry
more than one O-ring to be removed, always remove overnight.
the rear O-ring first. This allows the O-ring to slide Note: For proper brush cleaning of the adapter, cap,
over the forward rings without falling into the open feed tube, and orifice, see Figure 6-39, which
grooves. indicates proper brush usage.
4. Remove the retaining pin, mix inlet adapter, valve Rinse all parts with clean, warm water. Place the
cap, and the piston from the pump cylinder. Remove pump parts on a clean, dry surface.
all the O-rings and the valve gasket.
8. Wipe clean all exterior surfaces of the freezer.
5. Return to the freezer with a small amount of cleaning
solution. With the black-bristle brush, brush clean the
rear shell bearing at the back of the freezing cylinder
Brush clean the drive hub opening in the rear wall of
the mix hopper.
10361

Figure 6-38

6-12 Model C706 Operating Procedures

 OPERATING PROCEDURES

2 4 1 5
3
1 1

2 5
3
1
2
3

5
5
3
4 6
2

Figure 6-39

Item Description Part No. Item Description Part No.

1 White Bristle - 1/2” x 1/2” 054068 4 White Bristle - 1/2” x 1” 013072

2 White Bristle - 3/16” x 1” 050103 5 White Bristle - 3” x 1/2” 039718

3 Black Bristle - 1/4” x 1-1/4” 013072

Operating Procedures Model C706 6-13

 OPERATING PROCEDURES

Notes:

6-14 Model C706 Operating Procedures

Section 7 Operator’s Checklist

During Cleaning and Sanitizing  On a designated day of the week, run the mix as
low as feasible and discard after closing. This will
Cleaning and sanitizing schedules are governed by
break the rerun cycle and reduce the possibility of
federal, state, or local regulatory agencies and must be
high bacteria and coliform counts.
followed accordingly. If the machine has a Standby mode,
it must not be used in lieu of proper cleaning and  Properly prepare the cleaning and sanitizing
sanitizing procedures and frequencies set forth by the solutions. Read and follow label directions
ruling health authority. The following checkpoints should carefully. Too strong of a solution may damage the
be stressed during cleaning and sanitizing operations: parts, and too weak of a solution will not do an
adequate job of cleaning or sanitizing.
 Temperature of the mix in the mix hopper and
walk-in cooler should be below 40°F (4.4°C.).
IMPORTANT! Cleaning and sanitizing must be
performed daily.
Regular Maintenance Checks
 Replace scraper blades that are nicked or
damaged. Before installing the beater assembly,
ALWAYS FOLLOW LOCAL HEALTH CODES. make sure the scraper blades are properly
attached to the helix.
 Check the rear shell bearing for signs of wear
(excessive mix leakage in drip pan) and make
Troubleshooting Bacterial Count sure it is properly cleaned.
 Thoroughly clean and sanitize the machine  Using a screwdriver and cloth towel, clean the
regularly, including complete disassembly and rear shell bearing and the female square drive
brush cleaning. socket free of lubricant and mix deposits.
 Use all brushes supplied for thorough cleaning.  Dispose of O-rings and seals if they are worn,
The brushes are specially designed to reach all torn, or fit too loosely, and replace with new.
mix passageways.  Follow all lubricating procedures. See “Assembly”
 Use the white bristle brush to clean the mix feed on page 6-1. 7
tube, which extends from the hopper down to the  If your machine is air-cooled, check the
rear of the freezing cylinder. condensers for accumulation of dirt and lint. Dirty
 Use the black-bristle brush to thoroughly clean the condensers will reduce the efficiency and capacity
rear shell bearing at the rear of the freezing of the machine. Condensers should be cleaned
cylinder. Be sure to have a generous amount of monthly with a soft brush. Never use screwdrivers
cleaning solution on the brush. or other metal probes to clean between the fins.
 If local health codes permit the use of rerun, make Note: For machines equipped with an air filter, it will be
sure the mix rerun is stored in a sanitized, covered necessary to vacuum the filters clean on a monthly
stainless steel container and used the following schedule.
day. Do not prime the machine with rerun. When
using rerun, skim off the foam and discard, then
mix the rerun with fresh mix in a ratio of 50/50
during the day's operation. WARNING! Always disconnect electrical
power prior to cleaning the condenser. Failure to follow
this instruction may result in electrocution.

Operator’s Checklist Model C706 7-1

 OPERATOR’S CHECKLIST

 If your machine is equipped with an auxiliary Winter Storage

refrigeration system, check the auxiliary
If the place of business is to be closed during the winter
condenser for accumulation of dirt and lint. Dirty
months, it is important to protect the freezer by following
condensers reduce the refrigeration capacity of
certain precautions, particularly if the building is subject
the mix hopper. Condensers must be cleaned
to freezing conditions.
monthly with a soft brush. Never use screwdrivers
Disconnect the freezer from the main power source to
or other metal probes to clean between the fins.
prevent possible electrical damage.
 If your machine is water-cooled, check the water
On water-cooled freezers, disconnect the water supply.
lines for kinks or leaks. Kinks can occur when the
Relieve pressure on the spring in the water valve. Use air
machine is moved back and forth for cleaning or
pressure on the outlet side to blow out any water
maintenance purposes. Deteriorated or cracked
remaining in the condenser.
water lines should be replaced only by an
authorized Taylor service technician. Important! Failure to follow this procedure may cause
severe and costly damage to the refrigeration system.
Air/Mix Pump Checklist Your local Taylor service technician can perform this
 Dispose of O-rings and valve gaskets if they are winter storage service for you.
worn, torn, or fit too loosely. Replace them with Wrap detachable parts of the freezer, such as the beater,
new ones. blades, driveshaft, and freezer door, and place them in a
 Handle plastic pump parts with care to avoid nicks protected, dry place. Rubber trim parts and gaskets can
and cracks. be protected by wrapping them with moisture-proof
paper. All parts should be thoroughly cleaned of dried mix
 Make sure the air/mix pump is properly attached
or lubrication, which attract mice and other vermin.
to the drive hub, or severe and costly damage
may occur.

7-2 Model C706 Operator’s Checklist

Section 8 Troubleshooting Guide

Table 8-1
Page
Problem Probable Cause Remedy
Ref.
1. No product is being a. Freeze-up in mix inlet hole. a. Call a Taylor service technician to
---
dispensed with the draw adjust the mix hopper temperature.
valve open and the b. Beater motor out on reset. b. Reset the freezer. 5-3
machine in the Auto c. The beater is rotating c. Contact a Taylor service technician to
mode. counterclockwise from the correct rotation to clockwise from ---
operator end. operator end.
d. The circuit breaker is off or the fuse d. Turn the breaker on or replace the
---
is blown. fuse.
e. There is inadequate mix in the mix e. Fill the mix hopper with mix.
6-10
hopper.
2. The product is too stiff. a. The viscosity needs adjustment. a. Contact a Taylor service technician. ---
3. The product is too soft. a. Viscosity needs adjustment. a. Contact a Taylor service technician. ---
b. Not enough airspace around b. Allow for adequate airflow across the
3-2
machine. (Air-cooled machines) condenser.
c. Worn scraper blades. c. Replace regularly. 9-1
d. Dirty condenser. (Air-cooled d. Clean monthly.
7-1
machines)
e. Mix is out of date. e. Use only fresh mix. ---
f. Loss of water. f. Locate cause of water loss and
7-1
(Water-cooled machines) correct.
4. The mix in the mix a. The temperature is out of a. Call a Taylor service technician to
---
hopper is too cold. adjustment. adjust the mix hopper temperature.
5. The mix in the mix a. The temperature is out of a. Call a Taylor service technician to
---
hopper is too warm. adjustment. adjust the mix hopper temperature.
b. The mix hopper cover is not in b. Place the cover in position.
6-10
position.
c. The MIX REF light is not lit. c. Press the MIX REF key. 5-2
6. The driveshaft is stuck in a. Rounded corners of driveshaft, a. Call a Taylor service technician to
the drive coupling. coupling, or both. correct the cause and to replace the
necessary components. Do not ---
lubricate the hex end of the
driveshaft. 8
b. Mix and lubricant collected in the b. Brush clean the rear shell bearing
6-11
drive coupling. area regularly.
7. The freezing cylinder a. The scraper blades are damaged. a. Replace the scraper blades. 6-2
walls are scored. b. Machine was placed in Auto mode b. Place machine in Auto mode only
before all sanitizing solution was after priming is complete and all 6-9
removed from freezing cylinder. sanitizing solution is removed.
c. The front bearing is missing or c. Install or replace the front bearing.
6-3
worn on the freezer door.
d. The beater assembly is bent. d. Call a Taylor service technician to
repair or replace the beater and
---
correct the cause of insufficient mix in
the freezing cylinder.

Troubleshooting Guide Model C706 8-1

 TROUBLESHOOTING GUIDE

Page
Problem Probable Cause Remedy
Ref.
8. Excessive mix leakage a. Missing or worn seal on the a. Install or replace regularly.
6-1/9-1
into the rear drip pan. driveshaft.
b. The rear shell bearing is worn. b. Call Taylor service technician to
---
replace rear shell bearing.
9. Excessive mix leakage a. Missing or worn draw valve a. Install or replace regularly.
6-3/9-1
from door spout. O-rings.
b. Inadequate lubrication of draw b. Lubricate properly.
6-3
valve O-rings.
c. Wrong type of lubricant is being c. Use the proper lubricant (example:
used (example: petroleum-based Taylor Lube). 6-1
lubricant).
10.No freezer operation a. Machine is unplugged. a. Plug into wall receptacle. ---
after pressing the AUTO b. The circuit breaker is off or the fuse b. Turn the breaker on or replace the
key. ---
is blown. fuse.
c. The beater motor is out on reset. c. Reset the freezer. 5-3
11.Product is not feeding a. Inadequate level of mix in the mix a. Fill the mix hopper with mix.
6-10
into the freezing hopper.
cylinder. b. The mix inlet hole is frozen up. b. The mix hopper temperature needs
adjustment. Call a Taylor service ---
technician.
12.The air/mix pump will a. The circuit breaker is off. a. Check the breaker. ---
not operate when the b. The power cord is unplugged. b. Plug in the power cord. ---
PUMP key is pressed. c. The freezer is out on reset. c. Reset the freezer. 5-3
d. The pump motor is out on reset. d. Press the PUMP key to cancel pump
operation. Press the Reset button on
the side of the pump motor reducer. ---
Press the PUMP key to continue
pump operation.
13.The air/mix pump will a. The pump motor is out on reset. a. Press the AUTO key to cancel the
not operate when the pump operation. Press the Reset
draw valve is opened button on the side of the pump motor ---
and the machine is in reducer. Press the AUTO key to
the Auto mode. continue automatic operation.
b. The relay is malfunctioning. b. Contact a Taylor service technician. ---

8 14.The piston travels back

and forth but product is
a. Inspect the pump valve gasket. a. The pump valve gasket must be
installed correctly, fit tightly, and not ---
not being pumped. have any holes or lubrication.
b. Inspect the O-rings. b. O-rings must not be worn, torn, or fit
7-1
too loosely.
c. Check the pump cylinder. c. The piston must be assembled
correctly and fit snugly in the pump 6-5
cylinder.

8-2 Model C706 Troubleshooting Guide

 TROUBLESHOOTING GUIDE

Page
Problem Probable Cause Remedy
Ref.
15.Excessive pump a. Inadequate or incorrect lubrication a. Follow lubrication procedures
6-5
cylinder wear. of pump cylinder. carefully.
b. Incorrect ball crank rotation. b. Contact a Taylor service technician. ---
16.Pitting occurring inside a. Cleaner was left inside the pump a. After brush cleaning the pump
the pump cylinder. cylinder. cylinder, allow it to air dry. Follow 6-11
disassembly procedures.
17.The ball crank of the a. Pump motor rotation is incorrect. a. Contact a Taylor service technician.
---
motor reducer is broken.
18.Too much pressure in a. Plugged relief hole in the inlet tube. a. Clean.
---
the freezing cylinder.
19.Not enough pressure in a. Malfunctioning draw switch. a. Contact a Taylor service technician.
---
the freezing cylinder.

Troubleshooting Guide Model C706 8-3

 TROUBLESHOOTING GUIDE

Notes:

8-4 Model C706 Troubleshooting Guide

Section 9 Parts Replacement Schedule

Table 9-1
Part Description Every 3 Months Every 6 Months Annually

Drive Shaft Seal X

Scraper Blade X

Freezer Door Gasket X

Beater Shoes X

Draw Valve O-ring X

Prime Plug O-ring X

Feed Tube O-ring X

Air Orifice O-ring X

White Bristle Brush, 3 in. x 7 in. Inspect and replace if necessary. Minimum

White Bristle Brush, 1 in. x 2 in. Inspect and replace if necessary. Minimum

Black Bristle Brush, 1 in. x 2 in. Inspect and replace if necessary. Minimum

Double-Ended Brush Inspect and replace if necessary. Minimum

White Bristle Brush, 1/2 in. x 1/2 in. Inspect and replace if necessary. Minimum

White Bristle Brush, 3/16 in. x 1 in. Inspect and replace if necessary. Minimum

White Bristle Brush, 3 in. x 1/2 in. Inspect and replace if necessary. Minimum

Baffle-Threadless Molded Inspect and replace if necessary.

Parts Replacement Schedule Model C706 9-1

 PARTS REPLACEMENT SCHEDULE

Notes:

9-2 Model C706 Parts Replacement Schedule

Section 10 Limited Warranty on Equipment

TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS

Taylor Company is pleased to provide this limited warranty on new Taylor-branded freezer equipment available from
Taylor to the market generally (the “Product”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as
follows. All warranty periods begin on the date of original Product installation. If a part fails due to defect during the
applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or
remanufactured part, at Taylor’s option, to replace the failed defective part at no charge for the part. Except as
otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Product failure. This
limited warranty is subject to all provisions, conditions, limitations, and exclusions listed below and on the reverse (if
any) of this document.
Table 10-1
Product Part Limited Warranty Period

Soft Serve Insulated shell assembly Five (5) years

Frozen Yogurt Shakes Refrigeration compressor (except service valve) Five (5) years

Smoothies Beater motors Two (2) years

Frozen Beverage Beater drive gear Two (2) years

Batch Desserts Printed circuit boards and Softech™ controls beginning with Two (2) years
serial number H8024200

Parts not otherwise listed in this table or excluded below One (1) years

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins ninety
(90) days from the date of Product manufacture (as indicated by the product serial number). Proof of purchase may
be required at time of service.
2. This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are used.
3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the
Taylor Operator’s Manual.
4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.
5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.

10

Limited Warranty on Equipment Model C706 10-1

 LIMITED WARRANTY ON EQUIPMENT

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective parts, replacement parts, or new Products.
2. Normal maintenance, cleaning, and lubrication as outlined in the Taylor Operator’s Manual, including cleaning of
condensers.
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.
4. External hoses, electrical power supplies, and machine grounding.
5. Parts not supplied or designated by Taylor, or damages resulting from their use.
6. Return trips or waiting time required because a service technician is prevented from beginning warranty service
work promptly upon arrival.
7. Failure, damage, or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized
alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including but not limited to the
failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies.
8. Failure, damage, or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any
other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or
condition beyond the reasonable control of Taylor; operation above or below the electrical or water supply
specification of the Product; or components repaired or altered in any way so as, in the judgment of the
Manufacturer, to adversely affect performance, or normal wear or deterioration.
9. Any Product purchased over the Internet.
10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or
interruption of electrical service.
11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will void this
limited warranty.
13. Any cost to replace, refill, or dispose of refrigerant, including the cost of refrigerant.
14. ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this
limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to
jurisdiction.

10

10-2 Model C706 Limited Warranty on Equipment

 LIMITED WARRANTY ON EQUIPMENT

LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS,
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY
WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE COMPONENTS
UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL
DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES
OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED
WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER
PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.

10

Limited Warranty on Equipment Model C706 10-3

 LIMITED WARRANTY ON EQUIPMENT

Notes:

10

10-4 Model C706 Limited Warranty on Equipment

Section 11 Limited Warranty on Parts

TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS

Taylor Company is pleased to provide this limited warranty on new Taylor genuine replacement components and parts
available from Taylor to the market generally (the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as
follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will
provide a new or remanufactured Part, at Taylor’s option, to replace the failed defective Part at no charge for the Part.
Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Part failure.
This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse
(if any) of this document.
Table 11-1
Part's Warranty Class Code or Part Limited Warranty Period

Class 103 Parts¹ Three (3) Months

Class 212 Parts² Twelve (12) Months

Class 512 Parts Twelve (12) Months

Class 000 Parts No Warranty

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required at time
of service.
2. This limited warranty is valid only if the Part is installed and all required service work in connection with the Part is
performed by an authorized Taylor distributor or service agency.
3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.
4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the
Taylor Operator’s Manual.
5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.
6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate Taylor
Limited Warranty on freezer or grill equipment.
7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited
warranty.

1, 2
Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor freezer 11
equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.

Limited Warranty on Parts Model C706 11-1

 LIMITED WARRANTY ON PARTS

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective Parts, replacement Parts, or new Parts.
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning of
condensers or carbon and grease buildup.
3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including the
upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper assembly of
release sheets and clips as a result of grease buildup on the cooking surfaces, including but not limited to the
platen and plate, sides of the shroud, or top of the shroud.
4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or in the
case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or other small
wares used during the cooking process or as a result of the use of cleaners, cleaning materials or cleaning
processes not approved for use by Taylor.
5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any
release sheets and clips for the Product’s upper platen assembly.
6. External hoses, electrical power supplies, and machine grounding.
7. Parts not supplied or designated by Taylor, or damages resulting from their use.
8. Return trips or waiting time required because a service technician is prevented from beginning warranty service
work promptly upon arrival.
9. Failure, damage, or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized
alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including but not limited to the
failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies.
10. Failure, damage, or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any
other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or
condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or water supply
specification of the unit in which a part is installed; or Parts or the units in which they are installed repaired or
altered in any way so as, in the judgment of Taylor, to adversely affect performance, or normal wear or
deterioration.
11. Any Part purchased over the Internet.
12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or
interruption of electrical service.
13. Electricity, gas, or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is installed
will void this limited warranty.
15. Any cost to replace, refill, or dispose of refrigerant, including the cost of refrigerant.
16. ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this
limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to
jurisdiction.
11

11-2 Model C706 Limited Warranty on Parts

 LIMITED WARRANTY ON PARTS

LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/
OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY
WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER
THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES
(INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES OR
SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED
WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER
PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.

11

Limited Warranty on Parts Model C706 11-3

 LIMITED WARRANTY ON PARTS

Notes:

11

11-4 Model C706 Limited Warranty on Parts