Scribd
Upload
34 views1 page

PM SW 400 LF

The PMSW-400LF membrane element features a nominal membrane area of 400 sq.ft with a permeate flow rate of 9,000 gpd and a stabilized salt rejection of 99.8%. It operates under specific conditions including 32,000 ppm NaCl and 800 psi applied pressure, with a maximum operating temperature of 113°F. The document includes detailed specifications, operating data, and important notices regarding the use and installation of the membrane element.

Uploaded by

alonsofelicianopereira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
34 views1 page

PM SW 400 LF

The PMSW-400LF membrane element features a nominal membrane area of 400 sq.ft with a permeate flow rate of 9,000 gpd and a stabilized salt rejection of 99.8%. It operates under specific conditions including 32,000 ppm NaCl and 800 psi applied pressure, with a maximum operating temperature of 113°F. The document includes detailed specifications, operating data, and important notices regarding the use and installation of the membrane element.

Uploaded by

alonsofelicianopereira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

MEMBRANE ELEMENT PMSW-400LF

Low Fouling & Low Pressure Drop

SPECIFICATIONS

Nominal Membrane Area 400 sq.ft


Permeate Flow: 9,000 gpd (34.1 m3/d)
Stabilized Salt Rejection: 99.8 %
Membrane Polymer: Polyamide Thin-Film Composite
Feed Spacer thickness: 34 mil (0.864 mm)

The stated performance is based on the following conditions:

32,000 ppm NaCl


800 psi (5.5 MPa) Applied Pressure
77 F (25 C) Operating Temperature
10% Permeate Recovery
pH Range 6.5-7.0

A
C

B FEED PERMEATE

CONCENTRATE

A, inches B, inches C, inches Weight, lbs.


(mm) (mm) (mm) (kg)
40.0 (1016) 7.89 (200) 1.125 (28.6) 36 (16.4)

OPERATING DATA

Maximum Applied Pressure: 1200 psig (8.27 MPa)


Free Chlorine Tolerance: < 0.1 ppm
Maximum Operating Temperature: 113 F (45 C)
Continuous pH Range (Cleaning): 2– 11 (1 - 13)
Maximum Feedwater Turbidity: 1.0 NTU
Maximum Feedwater SDI (15 mins): 5.0
Maximum Feed Flow: 85 gpm (19.3 m3/h)
Minimum Ratio of Concentrate to Permeate Flow for any Element: 5:1
Maximum Pressure Drop: 15 psi

NOTICE:
PERMEATE FLOW FOR AN INDIVIDUAL ELEMENT MAY VARY + OR - 15 PERCENT. ALL MEMBRANE ELEMENTS HAVE A BRINE SEAL, INTERCONNECTOR, AND O-RINGS IN A SEALED
POLYETHYLENE PLASTIC BAG. USE GLYCERIN OR SILICON ONLY FOR LUBRICATION OF SEALS AND O-RINGS. ALWAYS AVOID STATIC PERMEATE BACKPRESSURE. WE OFFER DATA IN
GOOD FAITH BUT WITHOUT GUARANTEE. PLEASE REFER TO THE APPLICATION INFORMATION LITERATURE ENTITLED OPERATION GUIDELINES FOR MORE INFORMATION BEFORE
INSTALLING AND OPERATING THE ELEMENTS.

PERSALT MEMBRANES: 401 East Jackson Street Suite 2340, Tampa, FL 33602
Phone: (813) 803-6125 Fax: (813) 803-6126 – [email protected]

You might also like