NUMBER PART MATERIAL

1 O-RING (PROVIDES FRICTION FIT) RUBBER

2 MOUNTED PAIR OF ASPHERIC LENSES 0.55 NA/0.15 NA FOR 600-1050 nm -
3 COLLIMATION TUBE 6061-T6 ALUMINUM
4 9.0 mm LASER DIODE (SOLD SEPARATELY) -
5 RETAINING RING FOR 9.0 mm DIODE 6061-T6 ALUMINUM
- RETAINING RING FOR 5.6 mm DIODE (NOT SHOWN IN THIS CONFIGURATION) 6061-T6 ALUMINUM
- ADAPTER FOR 5.6 mm DIODE (NOT SHOWN IN THIS CONFIGURATION) 6061-T6 ALUMINUM
- 5.6 mm LASER DIODE (SOLD SEPARATELY) (NOT SHOWN IN THIS CONFIGURATION) -

THREAD 9 mm x 0.5 mm PITCH

THREAD 13-32/40 THREAD BEGINS 0.148" FROM
0.260" DEEP FRONT OF TUBE

5 4 3 2 1

0.58in 0.38in
14.7mm 9.7mm

0.10
LASER MOUNTING TO
EMITTING SURFACE
0.33in
8.5mm

NOTES/SPECIFICATIONS:

1. LENS CELL HAS 1.0 mm ADJUSTMENT RANGE FROM POSITION SHOWN, WHICH WAS DESIGNED
FOR TOSHIBA STANDARD 9 mm LASER PACKAGE
2. LENS TUBE DESIGN REQUIRES THE EMITTING SURFACE OF THE LASER TO BE
BETWEEN 1.7-3.2 mm FROM THE 9 mm MOUNTING FLANGE OF THE LASER DRAWING
3. USE THORLABS SPANNER WRENCH SPW301 FOR RETAINING RINGS, AS WELL AS LENSES PROJECTION
www.thor labs.com
NAME DATE
SHEET 1 OF 2: FOR 5.6 mm LASER DIODE CONFIGURATION SEE SHEET 2 DRAWN MG 12/MAR/10 FOCUSING TUBE
APPROVAL JC 20/OCT/22 MATERIAL REV
FOR INFORMATION ONLY COPYRIGHT © 2022 BY THORLABS
SEE TABLE D
NOT FOR MANUFACTURING PURPOSES VALUES IN PARENTHESIS ARE CALCULATED
ITEM # APPROX WEIGHT
AND MAY CONTAIN ROUNDOFF ERRORS LT230260P-B 0.07 kg
NUMBER PART MATERIAL
1 O-RING (PROVIDES FRICTION FIT) RUBBER
2 MOUNTED PAIR OF ASPHERIC LENSES 0.55 NA/0.15 NA FOR 600-1050 nm -
3 COLLIMATION TUBE 6061-T6 ALUMINUM
- 9.0 mm LASER DIODE (SOLD SEPARATELY) (NOT SHOWN IN THIS CONFIGURATION) -
- RETAINING RING FOR 9.0 mm DIODE (NOT SHOWN IN THIS CONFIGURATION) 6061-T6 ALUMINUM
6 RETAINING RING FOR 5.6 mm DIODE 6061-T6 ALUMINUM
7 ADAPTER FOR 5.6 mm DIODE 6061-T6 ALUMINUM
8 5.6 mm LASER DIODE (SOLD SEPARATELY) -

THREAD 9 mm x 0.5 mm PITCH

THREAD BEGINS 0.148" FROM
FRONT OF TUBE
THREAD 13-32/40
3 2 0.260" DEEP
6 8 7 1

0.58in 0.38in
14.7mm 9.7mm

0.08in
2.1mm
LASER MOUNTING TO
EMITTING SURFACE

0.09in
2.3mm

NOTES/SPECIFICATIONS:

1. LENS CELL HAS 1.0 mm ADJUSTMENT RANGE FROM POSITION SHOWN, WHICH WAS DESIGNED
FOR TOSHIBA STANDARD 9 mm LASER PACKAGE
2. LENS TUBE DESIGN REQUIRES THE EMITTING SURFACE OF THE LASER TO BE DRAWING
BETWEEN 1.7-3.2 mm FROM THE 9 mm MOUNTING FLANGE OF THE LASER PROJECTION
3. USE THORLABS SPANNER WRENCH SPW301 FOR RETAINING RINGS, AS WELL AS LENSES www.thor labs.com
NAME DATE
SHEET 2 OF 2: FOR 9.0 mm LASER DIODE CONFIGURATION SEE SHEET 1 DRAWN MG 12/MAR/10 FOCUSING TUBE
APPROVAL JC 20/OCT/22 MATERIAL REV
FOR INFORMATION ONLY COPYRIGHT © 2022 BY THORLABS
SEE TABLE D
NOT FOR MANUFACTURING PURPOSES VALUES IN PARENTHESIS ARE CALCULATED
ITEM # APPROX WEIGHT
AND MAY CONTAIN ROUNDOFF ERRORS LT230260P-B 0.07 kg