Scribd
Upload
258 views3 pages

Electronic Circuits - Ii: Part-A Instructions: All Three

The document is an examination paper for the Electronic Circuits II course, part of the Board Diploma Examination for the fourth semester, held in November/December 2022. It consists of three parts: Part A with short answer questions, Part B with detailed questions requiring comprehensive answers, and Part C with a single comprehensive question. The total marks for the examination are 80, with specific instructions for answering each part.

Uploaded by

palaji pradeep
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
258 views3 pages

Electronic Circuits - Ii: Part-A Instructions: All Three

The document is an examination paper for the Electronic Circuits II course, part of the Board Diploma Examination for the fourth semester, held in November/December 2022. It consists of three parts: Part A with short answer questions, Part B with detailed questions requiring comprehensive answers, and Part C with a single comprehensive question. The total marks for the examination are 80, with specific instructions for answering each part.

Uploaded by

palaji pradeep
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

74 4 0

* C20-EC–402

7440
BOARD DIPLOMA EXAMINATION, (C-20)
NOVEMBER/DECEMBER— 2022

DECE – FOURTH SEMESTER EXAMINATION

ELECTRONIC CIRCUITS – II
Time : 3 hours ] [ Total Marks : 80

PART—A 3×10=30

Instructions : (1) Answer all questions.


(2) Each question carries three marks.
(3) Answers should be brief and straight to the point and shall
not exceed five simple sentences.

1. Classify clippers.

2. List any three applications of clippers.

3. Define slew rate and CMRR.

4. List the characteristics of ideal operational amplifier.

5. List the advantages of integrated circuits over discrete circuits.

* 6. State the use of sweep voltage as time base.

7. Draw the pin diagram of 555 IC timer.

8. Define lock range of PLL.

9. Define the term resolution of D/A converter.

10. Define the term settling time of D/A converter.

/7440 1 [ Contd...

*
* PART—B 8×5=40

Instructions : (1) Answer either (a) or (b) from each question.


(2) Each question carries eight marks.
(3) Answers should be comprehensive and criteria for valuation
are the content but not the length of the answer.

11. (a) Explain the working of Zener diode clipper with waveforms.
( OR )
(b) Explain the working of unbiased negative diode clipper circuits.

12. (a) Explain the operation of Non-Inverting amplifier using Op-Amp


and derive the expression for voltage gain.
( OR )
(b) Draw the functional block diagram of an operational amplifier
and explain its operation.

13. (a) Explain the working of Op-Amp based Schmitt trigger circuit
with waveforms.
( OR )
(b) Explain with suitable circuit diagram the operation of RC phase
shift oscillator using Op-Amp.

14. (a) Explain with suitable circuit diagram the working of astable
* multivibrator using 555 IC.
( OR )
(b) Draw the internal block diagram of PLL – LM 565 and explain
its operation.

15. (a) Explain the D/A converter using R-2R ladder network.
( OR )
(b) Explain the A/D conversion using counter method.
/7440 2 [ Contd...

*
* PART—C 10×1=10

Instructions : (1) Answer the following question.


(2) The question carries ten marks.
(3) Answer should be comprehensive and criterion for valuation
is the content but not the length of the answer.

16. Prove that frequency of circuits using Op-Amp is dependent only on


the components connected externally.

★★★

/7440 3 AA22-PDF

*
COMPETITORS ACADEMY .IN

You might also like