Scribd
Upload
9 views

1a.Td ss1

The document is a technical drawing exam consisting of objective questions and theory sections. It covers topics such as freehand sketching, drawing instruments, properties of shapes, and methods for constructing polygons. The exam includes both multiple-choice questions and practical drawing tasks.

Uploaded by

Victor
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
9 views

1a.Td ss1

The document is a technical drawing exam consisting of objective questions and theory sections. It covers topics such as freehand sketching, drawing instruments, properties of shapes, and methods for constructing polygons. The exam includes both multiple-choice questions and practical drawing tasks.

Uploaded by

Victor
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

TECHNICAL DRAWING SS1 (second term exam)

SECTION A (objective)

1.Freehand sketching involves the use of eraser .....and

..........a.pencil , paper b.pencil,scale c.protractor,divider d.sharpener

Compass.

2.All these are sizes of drawing board except.........a.A4=210mm*297mm

b.A2=470mm*650mm c.A3=450mm*650mm d.AO=840mm*1189mm.

3..........is drawn at the bottom right hand corner of the drawing paper

a.information b.Tittle block c. Lettering d.dimensions.

4..........are used to draw vertical lines by placing one sides of the triangle containing the right angle
against the upper edge of the T square a.Drawing board b.set square c.Tee square d. Drawing paper.

5.........is used to draw arcs and circles a.pair of compass b.set square c.T square d.Drawing

Paper.

6.Which of the following is not required in freehand drawing? a.measurement b.symmetry

C.proportion d.neatness.

7.An is one which is less than....... a.60° b.90° c. 45° d.35°.

8.The drawing instrument used for measuring angles is .......a.compass b. ruler c. Protractor d. Set
square.

9.......... are plane figures bonded by 4 straight lines a. Encentric circle b.circle c.quadrilateral

d.tangent

10.All these are the properties of a quadrilateral except a.They have equal vertex b.It has all four sides
equal c.all its angles are right angle d.the diagonals are equal and they bisect each other at the centre
forming angles 90°.

11........is the process of putting down information on a drawing by means of letters,words and numbers
a.information b. Tittle block c. Lettering d.dimension.

12.........are used for angular measurements a. Pair of compass b. Set square c. Tee square d. Protractor.

13.Which of the following instrument is used to transfer measurements from one point to another a.a
pair of compass b.a pair of divider c. Protractor d. Set square.
14. A straight line is the shortest distance between.......points a.3 b 6 c.4 d.2.

15. Centreline is used to locate,represent the centre of ......a.arcs b.circles

C.hidden round feathers d.all of the above.

16. We use......for setting paper on the drawing board a. Pencil b. T square c.set square d.compass

17.The drawing instrument used for measuring angles is .......a.compass b.ruler c.protractor.

d.set square.

18. These are importance of td except a.its develop our skill b.it help to interpret drawing c.means of
communication d.its gives us information about events .

19. Pencil for lettering should be sharpened to.......point a.double b.curve c.conical d.fine.

20.Drawing material and instrument should be .......a Handle with care b.Handle roughly

C.kept in the roof d. played with always.

SECTION B (Theory).

1a.Construct a regular polygon(i.e heptagon when given the distance across corners

b.Define tangent

C.

2a. Define scale drawing

B.Draw using scale 1:100 of a chair having length 5cm and width 10cm.

C.Draw a regular octagon using exterior angle method

3a.Define polygon

B.State the two ways of constructing polygons

C.using circumscribing circle method of radius 5cm.construct a regular heptagon and hexagon.

4.Define Enlargement

You might also like