Scribd
Upload
39 views4 pages

WWW - Manaresults.co - In: Production Drawing

The document outlines the examination details for the DME Fourth Semester Production Drawing, including instructions for answering questions and marking schemes. It consists of two parts: Part A with five questions on calculations, drawings, and definitions, and Part B requiring detailed drawings and process sheets for specific assembly drawings. The total marks for the exam are 60, with a time limit of 3 hours.

Uploaded by

solidedgeclown
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
39 views4 pages

WWW - Manaresults.co - In: Production Drawing

The document outlines the examination details for the DME Fourth Semester Production Drawing, including instructions for answering questions and marking schemes. It consists of two parts: Part A with five questions on calculations, drawings, and definitions, and Part B requiring detailed drawings and process sheets for specific assembly drawings. The total marks for the exam are 60, with a time limit of 3 hours.

Uploaded by

solidedgeclown
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

7 4 6 0

*
C20-M–407

7460
BOARD DIPLOMA EXAMINATION, (C-20)
JUNE/JULY— 2022

DME – FOURTH SEMESTER EXAMINATION

PRODUCTION DRAWING
Time : 3 hours ] [ Total Marks : 60

PART—A 5×4=20

Instructions : (1) Answer all questions.

(2) Each question carries five marks.

(3) Draw the following neatly with proportionate dimensions.

(4) Use of production drawing tables is allowed.

1. Calculate the values of clearance/interference, hole tolerance and


shaft tolerance for the assemblies with a basic size of 40 mm and
tolerances indicated (a) 120 H7/S6 and (b) 40 G7/h6.

2. Draw the symbols for the following geometrical tolerance


* characteristics :

(a) Profile of any line

(b) Cylindricity

(c) Profile of any surface

(d) Flatness

(e) Circularity

/7460 1 [ Contd...

www.manaresults.co.in
3. Write the surface
* roughness values for the following manufacturing
processes :

(a) Lapping

(b) Reaming

(c) Drilling

(d) Diecasting

(e) Forging

4. Write the meaning of the following designations :

(a) Fe 520 L

(b) X10Crl8Ni9S3

(c) Hex Screw M8×30- IS : 1364– P– 8·8

(d) Solid Taper Pin 10×60, IS : 6688

(e) Snap Head Rivet 6×25, IS : 2155

/7460 2 [ Contd...

www.manaresults.co.in
* PART—B

Instructions : (1) Answer any one question.


(2) Each question carries forty marks.

5. Study the given assembly drawing of Screw jack :


(a) Draw the part drawings. 20
(b) Mention suitable fits and tolerances wherever required. 4
(c) Indicate surface roughness values/symbols to the components. 6
(d) Prepare process sheet for the manufacturing of “Screw”. 7
(e) Prepare bill of materials. 3

/7460 3 [ Contd...

www.manaresults.co.in
6. Study the given
* assembly drawing of Drill Jig :
(a) Draw the part drawings. 20
(b) Mention suitable fits and tolerances wherever required. 4
(c) Indicate surface roughness values/symbols to the components. 6
(d) Prepare process sheet for the manufacturing of “Drill Bush”. 7
(e) Prepare bill of materials. 3

★★★

/7460 4 AA22-PDF

www.manaresults.co.in

You might also like