DELTA_NC300_O_EN_20140428

Operation Manual NC300

Table of content
Chapter 1: Table of group menu
1.1 Table of system group menu ......................................................................... 1-1
1.2 Primary control panel function keys .............................................................. 1-9
1.3 Secondary control panel function keys.......................................................... 1-11

Chapter 2: Table of function groups

2.1 Auto mode (AUTO) ........................................................................................ 2-1
2.2 Edit mode (EDIT) ........................................................................................... 2-1
2.3 Manual mode (MDI) ....................................................................................... 2-1
2.4 Hand wheel mode (MPG) .............................................................................. 2-1
2.5 Jog mode (JOG) ............................................................................................ 2-2
2.6 Home mode (HOME) ..................................................................................... 2-2

Chapter 3: POS group

3.1 Absolute coordinate ..................................................................................... 3-1
3.2 Relative coordinate ...................................................................................... 3-2
3.3 Mechanical coordinate ................................................................................. 3-3

Chapter 4: PRG group

4.1 Network setting .............................................................................................. 4-2
4.2 Add (create new file) .................................................................................... 4-8
4.3 Copy .............................................................................................................. 4-9
4.4 Paste ............................................................................................................. 4-10
4.5 Delete (for files and folders) .......................................................................... 4-11
4.6 Select/Deselect multiple files ......................................................................... 4-12
4.7 Rename ......................................................................................................... 4-15
4.8 Add folder ...................................................................................................... 4-16
4.9 File searching ................................................................................................ 4-17

Revision April, 2014 i

NC300 Operation Manual

4.10 File merge ..................................................................................................... 4-18

4.11 Macro file ...................................................................................................... 4-18
4.12 File editing..................................................................................................... 4-19
4.12.1 Search by line number ......................................................................... 4-20
4.12.2 Search by keywords ............................................................................ 4-21

4.12.3 Block starting／ending point ................................................................ 4-22

4.12.4 Delete (lines and blocks) ..................................................................... 4-23

4.12.5 Copy and paste (line and block) .......................................................... 4-24
4.12.6 Undo .................................................................................................... 4-25
4.13 Other mode functions .................................................................................. 4-26

Chapter 5: OFS group

5.1 Coordinates setting ..................................................................................... 5-1
5.1.1 Auto setting ......................................................................................... 5-2
5.1.2 Absolute input ..................................................................................... 5-8
5.1.3 Incremental input ................................................................................. 5-10
5.1.4 Rectangle center ................................................................................. 5-11
5.1.5 Circle center ........................................................................................ 5-14
5.2 Tool register ................................................................................................... 5-16
5.3 Tool magazine register .................................................................................. 5-21
5.4 Macro variable ............................................................................................... 5-27
5.4.1 Local variable ...................................................................................... 5-27
5.4.2 Global variable .................................................................................... 5-28
5.4.3 Retaining variable ............................................................................... 5-28
5.4.4 Expanded variable .............................................................................. 5-29

Chapter 6: GRA group

6.1 Machining path .............................................................................................. 6-2
6.2 Machining preview ........................................................................................ 6-3

ii Revision April, 2014

Operation Manual NC300

Chapter 7: ALM group

7.1 Alarm............................................................................................................. 7-1
7.2 Message log .................................................................................................. 7-2

Chapter 8: DGN group

8.1 Machining information ................................................................................... 8-1
8.2 User variable ................................................................................................. 8-4
8.3 MLC .............................................................................................................. 8-5
8.3.1 Bit ........................................................................................................ 8-6
8.3.2 Register ............................................................................................... 8-7
8.3.3 Device monitoring ............................................................................... 8-9
8.3.4 Search line .......................................................................................... 8-11
8.3.5 Editor ................................................................................................... 8-11
8.3.6 Operation .......................................................................................... 8-14
8.4 System monitoring ........................................................................................ 8-16
8.4.1 Variable .............................................................................................. 8-16
8.4.2 I/O monitoring .................................................................................... 8-19
8.4.3 Servo monitoring ............................................................................... 8-20
8.5 Password setting ........................................................................................... 8-21
8.5.1 System permission .............................................................................. 8-21
8.5.2 Equipment permission ......................................................................... 8-22
8.5.3 User permission .................................................................................. 8-24
8.5.4 Timed use ........................................................................................... 8-26
8.6 System information ....................................................................................... 8-30
8.7 Gain adjustment ............................................................................................ 8-32
8.8 Import ............................................................................................................ 8-37
8.9 Export............................................................................................................ 8-38
8.10 Multi language download .............................................................................. 8-39
8.11 System recovery ........................................................................................... 8-39
8.12 LOGO download ........................................................................................... 8-40

Revision April, 2014 iii

NC300 Operation Manual

Chapter 9: PAR Group

9.1 Machining parameter .................................................................................. 9-1
9.2 Operation parameter ................................................................................... 9-2
9.3 Tool magazine parameter............................................................................ 9-3
9.4 Spindle parameter ....................................................................................... 9-4
9.5 Mechanical parameter ................................................................................ 9-5
9.6 Origin parameter ......................................................................................... 9-6
9.7 Network setup ............................................................................................. 9-7
9.8 Compensation parameter............................................................................ 9-9
9.9 System parameter ....................................................................................... 9-11
9.10 MLC setting ................................................................................................. 9-13
9.11 Graph parameter ......................................................................................... 9-14
9.12 Servo parameter ......................................................................................... 9-15
9.13 Channel setup ............................................................................................. 9-16
9.14 RIO setting .................................................................................................. 9-18
9.15 Search ........................................................................................................ 9-19

Chapter 10: SOFT group

10.1 Control panel ............................................................................................ 10-1
10.2 Factor regulation ........................................................................................ 10-4
10.3 Axis operation ........................................................................................... 10-5

Appendix A: Group function map

iv Revision April, 2014

Chapter 1: Table of group menu NC300

Chapter 1: Table of group menu

1.1 Table of system group menu

POS coordinates function

Layer 1 Layer 2 Layer 3 Layer 4
ABS - - -
CLR ALL - -
CLR X - -
REL
CLR Y - -
(Connect to the physical
CLR Z - -
axis to display the axial
CLR A
clear function)
CLR B
CLR C
MECH - - -

[Edit mode]
PRG program function_file manager
Layer 1 Layer 2 Layer 3 Layer 4
NEW FILE - - -
COPY FILE - - -
PASTE - - -
DEL (file/folder)
SEL TOGL
CANCEL
FOLDER - - -
RENAME
FIND FILE - - -
MERGE - - -
MACRO - -

Revision April, 2014 1-1

NC300 Chapter 1: Table of group menu

PRG program function_file editor

Layer 1 Layer 2 Layer 3 Layer 4

COPY -
PASTE -
DEL - -
UNDO - -
File editing B START - -
B END -
LABLE
NEXT
STRING
PREV

[Auto mode]
Layer 1 Layer 2 Layer 3 Layer 4
SF set - - -
START RUN

[JOG / MPG mode] program editing

Layer 1 Layer 2 Layer 3 Layer 4
SF set - - -
TEACH RAPID
LINEAR
ARC P1
P2
P3
PLANE SEL
DEL
SAVE
NEW FILE
MECH / ABS

[Manual mode] program editing

Layer 1 Layer 2 Layer 3 Layer 4
LOAD - - -
SAVE - - -
CLEAR - - -

[Homing mode] program editing

Layer 1 Layer 2 Layer 3 Layer 4
SF set - - -

1-2 Revision April, 2014

Chapter 1: Table of group menu NC300

Offset (OFS) function

Layer 1 Layer 2 Layer 3 Layer 4
CLR REL -
CLR ALL -
AUTO SET L -
SET L/2 -
SET P -
ABS - -
INC - -
X1 -
X2 -
COORD
Y1 -
SQUARE
Y2 -
SET -
SET Z -
P1 -
P2 -
CIRCLE P3 -
SET -
SET Z -
ABS - -
INC - -
H SET - -
CUTTER H/D -
WEAR -
CLEAR
LIFE -
ALL -
SET (※ jog mode) -
Maga 1 RST ALL(※ jog mode) -
LOCK (※ jog mode) -
MAGA
SET (※ jog mode)
Maga 2 RST ALL(※ jog mode)
LOCK (※ jog mode)
LOCAL - -
MACRO GLOBAL - -
HOLD - -
Revision April, 2014 1-3
NC300 Chapter 1: Table of group menu

EXPAND

Graphic (GRA) function

Layer 1 Layer 2 Layer 3 Layer 4
X-Y / Y-Z / X-Z /
- -
X-Y-Z
CENTER - -
ZOOM IN - -
ZOOM OUT
CUTTING PATH DRAW
STOP DRAW
UP
DOWN
LEFT
RIGHT - -
X-Y / Y-Z / X-Z /
X-Y-Z
CENTER
ZOOM IN
CUTTING PREVIEW ZOOM OUT
(※Auto Mode) PREVIEW
CANCEL PREVIEW
UP
DOWN
LEFT
RIGHT

Alarm (ALM) function

Layer 1 Layer 2 Layer 3 Layer 4
ALARM - -
HISTORY CLR ALL - -

Diagnosis (DGN) function

Layer 1 Layer 2 Layer 3 Layer 4
SET - -
PROCESS CLR TIME - -
CLR NR - -
Sys VAR -
US DEC -
HEX
USER VAR
USER VAR S DEC
FLOAT
DEL
X -
Y -
MLC BIT
M -
A -
1-4 Revision April, 2014
Chapter 1: Table of group menu NC300

T -
C -
T -
C (16) -
C (32)
D
V
REG
Z
US DEC
HEX
S DEC -
FLOAT -
US DEC -
HEX
DEV MON
S DEC
FLOAT
LD -
LDI -
LDP -
LDF -
OUT -
APP -
— -
｜ -
DEL V-LN -
ADD LN -
DEL LN -
DEL -
LABLE -
TABLE -
X
EDITOR Y
(※edit mode) M
A
T
C
SYMBOL
D
P
I
DEL
COPY
PASTE
SAVE -
IMPORT IMPORT
EXPORT
EXPORT
NEW FILE
JUMP TO -
SELECT -
CUT -
Revision April, 2014 1-5
NC300 Chapter 1: Table of group menu

COPY -
PASTE -
ON -
SET(※edit mode) OFF -
RUN/STOP -
JUMP TO
SYS VAR -
CH VAR
AXIS VAR -
IF VAR
VAR MONI
US DEC -
SYS MONI
BIN
HEX
S DEC
I/O MONI
SRV MONI - -
SYSTEM
STATUS FW SN
HW SN
UNLOCK -
S SCP
LOCK
PWD CHG -
LOCK/UNLOCK -
M SCP
RST U1
RST U2
PWD CHG -
PWD U1 SCP
LOCK/UNLOCK -
PWD CHG
U2 SCP
LOCK/UNLOCK
SETTING
RELEASE -
EXPIRE
PWD CHG
EXP SCP
LOCK/UNLOCK
NEXT AX - -
READ - -
COMPUTE
WR GAIN - -
WR NOTH - -
TUNING
RUN - -
(※jog or hand wheel
JOG ← -
mode)
JOG → -
POS 1 -
POS 2 -
TAP RIV TAP SET -
SERVO - -
TEXT WR
IMPORT IMPORT - -
EXPORT EXPORT - -
RECOVER OK - -
1-6 Revision April, 2014
Chapter 1: Table of group menu NC300

LOGO WR - - -

System parameter (PAR) function

Layer 1 Layer 2 Layer 3 Layer 4
PROCESS - - -
OPERATE - - -
MAGA - - -

SPINDLE - - -
MACHINE - - -
HOME - - -

NETWORK DEFAULT
OK - -
um - -
COMP um+ - -
IMPORT - -

IMPORT+ - -
DEFAULT - -
SYSTEM
COLOR - -

DEFAULT - -
MLC
COLOR - -
DEFAULT - -
GRAPHIC
COLOR - -
SERVO READ - -
CONFIG
(Except Auto and MDI OK - -
mode)
SET RIO
(Except Auto and MDI OK - -
mode)
SEARCH - - -

SOFT group selection function

(Example: without physical control panel)
Program Hand wheel Tool magazine
Control panel Spindle forward
execution simulation forward
functions
Tool magazine
Stop execution Mechanical lock Spindle stop
backward

Revision April, 2014 1-7

NC300 Chapter 1: Table of group menu

Chip removal Spindle

Single step pause Program dry run
forward backward
Chip removal
Selection stop Mechanical lock
backward
Spindle
Single step ignore Z-axis lock Blow air
positioning
Program
Cutting fluid Working light Limit remove
protection
Increasing - - -
decreasing - - -
Factor adjust
100% - - -
0% - - -
X← - - -
X→ - - -
Y↗ - - -
Axis operations
Y↙ - - -
Z↑ - - -
Z↓ - - -

Software group – selection function

(Example: with physical control panel)
Layer 1 Layer 2 Layer 3 Layer 4
Program dry run Chip removal forward -
Chip removal
Function lock -
backward
Control panel Z-axis lock Auto power off -
functions
Mechanical lock Z-axis lock -
Spindle positioning Self-define 1 -
Blow air Self-define 2 -

1-8 Revision April, 2014

Chapter 1: Table of group menu NC300

1.2 Primary control panel function keys

Modes that
Name Description having this
function
One of the group keys. Coordinates
Every mode
display group key.

One of the group keys. Program edit group

Every mode
key.

One of the group keys. Coordinates setup

Every mode
and tool offset setup group key.
One of the group keys. Diagnosis function,
system parameter, and system status Every mode
group key.
One of the group keys. Alarm display
Every mode
group key.

One of the group keys. Path display group

Every mode
key.

Special group key. System parameter

Every mode
setup group key.

Special group key. Software control panel

Every mode
group key.

Reset key Every mode

Axis position and command code PRG group

PRG, OFS, DGN

Numeric key (computing symbol)
… group

Decimal point (computing symbol) PRG, OFS group

Negative sign (computing symbol) PRG, OFS group

PRG, OFS, DGN

Page up and page down respectively
group

Revision April, 2014 1-9

NC300 Chapter 1: Table of group menu

Modes that having

Name Description
this function

Arrow keys (Up, Down, Left and Right) PRG, OFS, DGN
(computing symbol) group

Jump to beginning (end) of word PRG group

Space PRG group

Upper/lower case shift PRG group

Delete (Insert) PRG group

Delete letter in front of cursor PRG group

PRG, OFS, DGN

Enter key
group

Exit dialog box PRG, DGN group

Parentheses PRG group

Every mode and

Left and right function key
group function

Every mode and

Function key
… group function

1-10 Revision April, 2014

Chapter 1: Table of group menu NC300

1.3 Secondary control panel function keys

Name Description

Auto mode: The program executes the specific mode

Edit mode: File management and program editing mode

Jog mode: Machine tools operation mode

Hand wheel mode: Hand wheel operates machine tools axis

Manual mode: Simple program input and execution mode

Homing mode: Rapidly return to home sensor

X-axis forward, X-axis backward: In JOG mode, manually

operate X-axis in forward or backward direction

Y-axis forward, Y-axis backward: In JOG mode, manually

operate Y-axis in forward or backward direction

Z-axis forward, Z-axis backward: In JOG mode, manually

operate Z-axis in forward or backward direction

Rotation-axis forward, Rotation-axis backward: In JOG mode,

manually rotate the axis in forward or backward direction

Spindle forward: Spindle moves forward in manual control

Spindle stop: Spindle stops in manual control

Spindle backward: Spindle moves backward in manual control

Cut feeding and jog ratio increasing/decreasing adjustment

Fast feeding ratio increasing/decreasing adjustment

Spindle speed ratio increasing/decreasing adjustment

Revision April, 2014 1-11

NC300 Chapter 1: Table of group menu

Name Description

Single step pause: After enabling the function, the system stops
execution when finish one single step.

Limit release: When the limit protection is effective, it is the main

key to clear the limit alarm.

Single step ignore: Enter “ / ” in the front and press to

enable this function.
Tool magazine forward: In safe mode, it enables the tool
magazine to move one position

Tool magazine backward: In safe mode, it enables the tool

magazine to reverse one position

Selection stop: Press and enter M01 command to

enable this function
Hand wheel simulation: During the program execution, after
enabling this function, the hand wheel can be used to control the
speed
Cutting fluid ON/OFF: The switch of switching On/Off the cutting
fluid

Working light: The switch of turning On/Off the working light

1-12 Revision April, 2014

Chapter 2: Table of function groups NC300

Chapter 2: Table of function groups

2.1 Auto mode (AUTO)
The system must be in AUTO mode before a program can be executed. This enables
users to validate machining program, cutting conditions, and coordinates of positions
before execution as well as to avoid unexpected operation by incorrectly pressing keys
in non-auto mode. The AUTO mode allows running program only. Users cannot edit
the program nor do manual axial offset among other operations.

2.2 Edit mode (EDIT)

Program editing only can be done in EDIT mode. In EDIT mode, users may fully
access various program editing functions available in PROGRAM group. Please note
that program cannot be executed and do manual axial offset either as only the file
editing function is available in this mode.

2.3 Manual mode (MDI)

Users can input a single step program with screens available in PRG group and run it
in MDI mode. As most MDI programs are simple ones manually entered by users,
there is no need to have too much program content. MDI's PRG group screens allow a
single step program of up to 17 statements. General program editing and editing and
manual axial operations are unavailable in MDI mode.

2.4 Hand wheel mode (MPG)

Manual axial offset for each axis with external hand wheel can be done in MPG mode
for fast and solid axial movements. The program editing, execution, and jog operations
are prohibited in MPG mode.

Revision April, 2014 2-1

NC300 Chapter 2: Table of function groups

2.5 Jog mode (JOG)

Pressing relevant axial movement keys in secondary control panel can do axial jog
offset in JOG mode. The speed and distance of each jog movement is controlled by the
jog factor key. With the rapid feeding activation key and axial keys, the workbench can
be moved. The axial moving speed is set by the rapid factor and can enable moving
the workbench in long distance of each axis. Both program execution and editing
functions are unavailable in JOG mode. Only manual axial offset with relevant axial
movement keys can do in secondary control panel.

2.6 Home mode (HOME)

The HOME mode simplifies the manual origin reset operation. When it is in HOME
mode, the axis will return to its mechanical origin by pressing all the axial movement
keys in secondary control panel. After re-starting the controller, it is required to reset
each axis to its mechanical origin by running the HOME mode first for executing the
program. Otherwise, the controller stops the program execution function.

Group screen overview

Screens of function groups of this controller provide a full range of information. Some
of the screens of each group are illustrated below.

Name of Line
current
POS group: program
being
executed

Display of
current group

Current
coordinates
data

S: Spindle speed (command

value)
F: Feed rate (command value)
S.lod: spindle load
S.act: actual spindle speed rate
F.act: actual feed rate
t: pause time Current
T: tool number status
T.spindle: spindle number
T.stdlby: standby tool number

Current Fast Feeding Spindle

system speed factor ratio factor ratio
mode ratio

As shown in the figure above, the system status column tells the status of this
system for the controller user's reference. Valid statuses of the system in terms of
priority are: MLC stop, servo not ready, emergency stop, in process, in operation,
program stop, and preparation completed.

2-2 Revision April, 2014

Chapter 2: Table of function groups NC300

PRG group: (auto mode) Name of current Line being

program executed

Display of F.act: actual feed rate

current group S.act: actual spindle speed
D: tool diameter compensation
ID
H: tool length compensation ID
Program content T: tool ID
being executed F: Feed rate
S: Spindle speed
t: pause time
CYC: Single processing time

Information of
each coordinate
that has being
executed
Current
command
status

Current
system
mode Each current
motion rate

Edit mode:

File list File information

Display folder Display data on
and program size of file/folder,
files modification
date and time,
etc.

File contents
Display
program
statements
contained in the
file

Revision April, 2014 2-3

NC300 Chapter 2: Table of function groups

Manual mode:

Manual mode

Coordinates
information

Display the
information of
absolute/remaining
coordinate

The information of feed

rate, spindle speed and
compensation Command status
information

OFS group: (coordinates system data)

Coordinates
information
Mechanical/relative
coordinates

Coordinates system
setup
Offset coordinates
/G54~G59

Tool data:

Compensation
Compensation ID data
(H/D) Tool length and
diameter as well
as length and
diameter
compensation

Auxiliary display
Display current
mechanical
coordinates and
Compensation actual position of
data input the Z-axis
column

2-4 Revision April, 2014

Chapter 2: Table of function groups NC300

Gain adjustment:

Anchor point
setup
Anchor point 1/
Anchor point 2

Servo parameter ID
Servo parameter ID
and name

Adjustment
conditions

System existing settings

Calculation result after
adjustment
Display active servo settings

Display calculation
result of auto gain

MLC operation/edit:

MLC
program

Input
column

Revision April, 2014 2-5

NC300 Chapter 2: Table of function groups

ALM group:

Alarms
occurring in
chronological
sequence

Alarm category
ID

Alarm message

GRA group:

Coordinate information
Mechanical
coordinate/absolute
Path diagram coordinate
Display program path

2-6 Revision April, 2014

Chapter 3: POS group NC300

Chapter 3: POS group

The POS group function displays data on mechanical, absolute, and relative coordinates.
The display can up to three straight line axes and one rotation axis based on the settings of
the number of rotation axes.
Name of Line
current being
program execute

Display of
current group

Current
coordinates
data

S: Spindle speed (command

value)
F: Feed rate (command value)
S.lod: spindle load
S.act: actual spindle speed
rate
F.act: actual feed rate
t: pause time
T: tool ID Current
T.spindle: spindle ID status
T.stdlby: standby tool ID

Current Spindle
system Alarm Fast Feeding
display speed factor ratio factor ratio
mode ratio

Figure: 3-1-1

3.1 Absolute coordinate

The absolute coordinates are based on the origin of the machining program. These
coordinates data are used to provide the coordinates in the program and can validate
the movement position of the single program step.

See below for operation details:

(1) Press key to open the coordinate group function display with absolute
coordinates, relative coordinates, and mechanical coordinate options in the
function bar.

(2) Press key (ABS) to enter the absolute coordinates screen.

Revision April, 2014 3-1

NC300 Chapter 3: POS group

3.2 Relative coordinate

The relative coordinate display movement distance against the origin.

See below for operation details:

(1) Press key to open the coordinate group function display with absolute
coordinate, relative coordinate, and mechanical coordinate options in the function
bar.

(2) Press key (REL) to enter the relative coordinate screen.

(3) Press key (CLR ALL) in the lower layer function bar to clear relative
coordinate of all axes.

Press key (CLR X) to clear the value shown on relative coordinate of the
X-axis.

Press key (CLR Y) to clear the value shown on relative coordinate of the
Y-axis.

Press key (CLR Z) to clear the value shown on relative coordinate of the
Z-axis.

Press key (CLR A) to clear the value shown on relative coordinate of the
A-axis.

Press key (CLR B) to clear the value shown on relative coordinate of the
B-axis.

Or press key (CLR C) of the next page to clear the value shown on
relative coordinate of the C-axis.

Note:
(a) Axial clear function of X, Y, Z, A, B and C axis will be displayed until it
connects to the corresponding actual axis.

3-2 Revision April, 2014

Chapter 3: POS group NC300

3.3 Mechanical coordinate

The mechanical coordinate cannot be cleared and do not vary with the selected
workpiece coordinates. And the mechanical coordinate data are unchangeable.

See below for operation details:

(1) Press key to open the coordinate group function display with absolute
coordinate, relative coordinate, and mechanical coordinate in the function bar.

(2) Press key (MECH) to enter the mechanical coordinate screen.

Revision April, 2014 3-3

NC300 Chapter 3: POS group

(This page is intentionally left blank.)

3-4 Revision April, 2014

Chapter 4: PRG group NC300

Chapter 4: PRG group

The PRG group manages and edits G code and macro files. The file explorer is divided into
three sections: (1) CF Card, internal memory, USB drive, and network; (2) folders and G
code files; (3) G code files only. Each section has its exclusive functions, e.g. breakpoint
search function under auto mode and program entry and execution under manual mode.
Program modification and management functions are also provided here, including
program file management and editing.

Figure 4-0-1

(1) Switch to Edit mode, press the key in first control panel and displays the
screen of [Program Function].

(2) Press or keys to move the cursor in the file explorer

screen and press key to enter the sub-manager screen to select G code
files.

(3) Select the desired G code file, press key to enter the file editing screen.

Then, press keys (scrolling one line up or down) or

keys (scrolling twenty lines up or down) to show the file contents.

Revision April, 2014 4-1

NC300 Chapter 4: PRG group

Note:
See the table below for the recommended format of the USB drive.

USB drive specifications

Format FAT32
Capacity As required

4.1 Network Setting

The NETWORK function remote connect to a PC through Ethernet. With CNC
network software, this remote connection enables one PC to execute the function of
online file management with multiple NC300 controllers. Users can share files with
PCs, and do file management and transmission-along-with-machining (DNC).

 Please set up communication protocol between the NC300 system and PC before
using the networking function. See below for setup steps:

NC300 system communication protocol: DGN group → System parameter →

Page 3 (see figure below)

Figure 4-1-1

4-2 Revision April, 2014

Chapter 4: PRG group NC300

Network setup parameters

Code Name Range or Formats
Length: 1~8
10030 Host name
Actual setting: 1~8 characters
Length: ×××．×××．×××．×××
10031 IP address
Actual setting: 192．168．0．2
Length: ×××．×××．×××．×××
10032 Subnet mask
Actual setting: 255．255．255．0
Length: ×××．×××．×××．×××
10033 Default gateway
Actual setting: 0．0．0．0
Length: 0~1
10034 Network function ON
Actual setting: 1
Length: 0~1
10035 DHCP ON
Actual setting: 0
IP address of remote Length: ×××．×××．×××．×××
10036
computer 1 Actual setting: 192．168．0．1
IP address of remote Length: ×××．×××．×××．×××
10037 Actual setting: 0．0．0．0
computer 2
IP address of remote Length: ×××．×××．×××．×××
10038 Actual setting: 0．0.0．0
computer 3
IP address of remote Length: ×××．×××．×××．×××
10039 Actual setting: 0．0．0．0
computer 4
IP address of remote Length: ×××．×××．×××．×××
10040 Actual setting: 0．0．0．0
computer 5
IP address of remote Length: 0~5
10041
folder sharing Actual setting: 0

Revision April, 2014 4-3

NC300 Chapter 4: PRG group

Communication protocol of PC: Set up TCP/IP in Networking of the operating

system (see Figure 4-1-2) or CNC Network software → Setup

Set up networking in PC operating system:

Figure 4-1-2

Steps: (a) Check "Use the following IP address" option then enter in sequence:
"IP address": 192 . 168 . 0 . 1
"Subnet mask": 255 . 255 . 255 . 0
(b) Press OK to complete the setting.

4-4 Revision April, 2014

Chapter 4: PRG group NC300

Networking settings at Network software end:

Figure 4-1-3

Steps: (a) Execute the CNC Network software, enter the Setup screen and enter the
settings listed below in sequence:
"IP address": 192 . 168 . 0 . 1
"Subnet mask": 255 . 255 . 255 . 0
(b) Press "Search CNC" key after entry is completed to connect with the CNC
based on the settings given here.

Revision April, 2014 4-5

NC300 Chapter 4: PRG group

■ DNC connection:
Through Network software, users may open the shared files in file sharing list. Then,
execute G code in transmission-along-with-machining (DNC) mode via Ethernet.
No extra disk space is required for file storage as only the path of shared files is recorded.

See the operation steps described below:

1. Finish the Network setup of PC and NC300 system through Ethernet

communication setting.
2. Start the CNC Network software.
3. Click Function bar ╴DNC operation tab.

Figure 4-1-4

4. Enter the "Edit mode" of NC300 system then enter the top layer
NETWORK\Option in file explorer.

Figure 4-1-5

4-6 Revision April, 2014

Chapter 4: PRG group NC300

5. Shared files display. Select and open the G code file that has been set to
share from the shared file.

6. Set NC300 to "Auto mode" then execute the Cycle start command to start
running the G code file by DNC connection. The execution method is the
same as the general file.

7. During DNC execution, contents of the file are displayed in the function
window of the CNC Network software's DNC operation, including name of
connected system, name of running DNC file, total number of lines, executing
line number and file contents. (File contents scroll down along with the
execution progress as shown in Figure 4-1-6).

DNC transmission display

Figure 4-1-6

Revision April, 2014 4-7

NC300 Chapter 4: PRG group

4.2 Add (create new file)

Users may use the Add function in "Edit mode" to create a new G code file from the
controller interface. See the operation steps described below:

(1) Set the system to "Edit mode".

(2) Press key, the screen of switching groups will be the [Program menu].

(3) In file explorer, press or keys to move the cursor to

the disk location and data layer for file creation (e.g. the 2nd or the 3rd layer under
CF or USB directory).

(4) Press key (NEW file) and the file name setup dialog box will pop up.

Figure 4-2-1

(5) Type alphanumeric letters (symbols are not included) in the box and press
key to create a new file.

4-8 Revision April, 2014

Chapter 4: PRG group NC300

Format of file name:

File format specifications

No restriction on format of master file name (file name must
Format of machining file name be unique in one directory)
(G code)
O + 0001~8999 (for subrountines)
Format of macro file name (O
O + 9000~9999
Macro)
Suffix a '-' symbol in the file name along with more
Remarks in file name
alphanumeric letters
Allowable format of filename
.NC .ANC .CNC .PIM .TAP .PTP .UOO .DEMO
extension
Format of M macro file name M + 10000~29999
Format of G macro file name G + 30000~49999
Maximum length of file name 31
Storage location Second and third management layer
Restriction symbol in file name ＊ ／ ＼ ∣ ＜ ＞ ？ “ ﹕

Note:
(a) File name must be unique in one directory, e.g. O0001 and O1 are treated as
the same.
(b) Only the machining files are displayed in file explorer. The macro files display
only upon special permission.
(c) It is allowed to use more than one decimal to name a G code file. The last one
should comply with the format of filename extension, e.g. 1.1.1.1.NC.

4.3 Copy
Use this option to copy existing files in the disk drive; see the operation steps
described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) In file explorer, press or keys to move the cursor to

disk location and data layer of the source file (e.g. the 2nd or 3rd layer under the
CF or USB directory).
(4) Move the cursor to the location of the target file.

(5) Press key (Copy file) to copy the file. Please note that it is required to
execute the "Paste" function to create the target file.

Revision April, 2014 4-9

NC300 Chapter 4: PRG group

4.4 Paste
As described in Section 4-3, it is required to execute this function together with the
Copy function to copy a file. This function is one of the PRG file explorer functions. See
the operation steps described below (continued from Section 4-3).

(6) Press or keys to move the cursor to the disk, data

directory or layer of the target file.

(7) Enter the directory of the target file, press key (Paste), enter a new name

or accept the old name of the target file in the popup dialog box. Press key
and the copy and paste functions are completed.

Note:
(a) Please note that if the newly copied file exists in the same directory, then its
name must differ from the source one.
(b) The system prompts an information box with the message 'Please copy a file
at first' if no copy operation has been done beforehand. The file past function
has no effect.
(c) The operation procedure for files in USB is the same: copy and paste the file
to CF card.

4-10 Revision April, 2014

Chapter 4: PRG group NC300

4.5 Delete (for files and folders)

This function deletes files and folders below the root layer.

See the operation steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) In file explorer, press or keys to move the cursor to

disk location and data layer of the file or folder to be deleted.
(4) Point to the file or folder to be deleted.

(5) Press key (DEL) and the "Do you really want to delete?" dialog box will

pop up. Press "Y" and key to delete the selected file or folder.

Note: The deleted file cannot be recovered by undoing the delete operation.

Revision April, 2014 4-11

NC300 Chapter 4: PRG group

4.6 Select/Deselect multiple files

In addition to single file operation, users may use the select/deselect function key from
the function bar in file explorer menu to select/deselect multiple files for copying or
deleting.

See the operation steps described below:

(1) Set the system to "Edit mode".

(2) Press and the screen of switching group will be the [Program menu].
(3) Enter the folder of multiple file selection.

(4) Press keys or keys to point to the desired files.

Press key (SEL TOGL) to select or deselect (see Figure 4-6-1). For files

that have been selected, pressing the key (SEL TOGL) again will cancel
their selection.

Figure 4-6-1

(5) Press key (Copy file) to copy multiple files.

4-12 Revision April, 2014

Chapter 4: PRG group NC300

(6) Point to another directory, press key (Paste) to paste multiple files as
shown in Figure 4-6-2.

Figure 4-6-2

See the operation steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].
(3) Enter the folder of multiple file selection.

(4) In file explorer, press keys or keys to point to the

desired files. Press key (SEL TOGL) for selection. For files that have

been selected, pressing the key (SEL TOGL) again will cancel their
selection.

(5) Press key (DEL) and the "Do you really want to delete?" dialog box will

pop up (see Figure 4-6-3). Press "Y" and key to delete the selected files.

Revision April, 2014 4-13

NC300 Chapter 4: PRG group

Figure 4-6-3

Note:
(a) Multiple files can be copied only to another folder. If trying to copy multiple
files in the same folder, the system prompts users to select another
destination path and ignore the paste operation.
(b) When duplicated file names are encountered while copying multiple files, the
NC300 numerical control system prompts users with an overwrite option
dialog box. Users can select "Y" (yes) to overwrite the existing file, or select
"N" (no) or press "EXIT" key to ignore the pasting operation.

4-14 Revision April, 2014

Chapter 4: PRG group NC300

4.7 Rename
Use this function to change the name of existing files. See the operation steps
described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) In file explorer, press or keys to move the cursor to

the disk location and data layer for file creation (e.g. the 2nd or 3rd layer under the
CF or USB directory).

(4) Press key to select the next option page.

(5) Point to the file that desired to rename and press key (Rename) and the file
name input dialog will pop up.
(6) Enter a new name of the file which differs from any file in the directory and press

key.

Note:
(a) A G code file can be added in layer two or three but not layer one in file
explorer.
(b) Naming and format for the file name during renaming follows the same rule
of adding a new file. If the name of a file after renaming is the same as an
existing file in the directory, the system prompts users with an error
message and aborts the renaming operation.

Revision April, 2014 4-15

NC300 Chapter 4: PRG group

4.8 Add folder

This function adds a new folder in the second layer of the file explorer for G code files.
The second layer may thus contain both G code files and folders.

See the operation steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) Press key to enter the next page.

(4) Press key (FOLDEL) in the second layer of the file explorer to display the
dialog box for directory name.

Figure 4-8-1

(5) Enter the name of the directory and press key to complete the creation.

This creates a new folder in the second layer of the file explorer and does file creation
and editing of files (such as G code files) at the third layer of the file explorer.

Format of directory name:

Format of directory name

Format of directory file name Any alphanumeric letter
Maximum length of directory name 31
Storage location The 2nd management layer

4-16 Revision April, 2014

Chapter 4: PRG group NC300

4.9 File searching

This function enables users search among many files and open a desired G code file.
With a given file name users can search and open files quickly.

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) In file explorer, press keys or keys to move the

cursor, press key to enter the target location in the second or third layer.

(4) Press key to select the next option page.

(5) Press key (FIND FILE), and the file name input dialog will pop up. Enter

the desired file name and press key to search and open the target file.

Note:
(a) Instead of searching all directories, this file searching function is limited to
one directory.
(b) This function searches exact instead of fuzzy file names.

Revision April, 2014 4-17

NC300 Chapter 4: PRG group

4.10 File merge

This function copies and merges two G code files into one.

See the operation steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be [Program menu].

(3) Press keys or keys to move the cursor, press

key to enter the target location in the second or third layer.

(4) Select the G code file that desire to copy.

(5) Press key (Copy file) to save the file in the system's clipboard.
(6) Move the cursor to the directory of the target file to be merged.

(7) Press key to select the next option page.

(8) Press key (MERGE) and the file name input dialog will pop up. Enter

the desired file name and press key to open the target file.
(9) Move the cursor to the location in the target file where desire the source file

to be copied to. Press key (Paste) to merge both files.

(10) Execute auto save, including switch mode, open other files or press the RESET
key, to complete the merge operation.

4.11 Macro file

This function manages and edits equipment specific macro files. With proper
permissions, users can use all the edit functions to manage and edit macro files as
described in Section 4.12. Otherwise, users can only browse existing macro files but
cannot view or edit the contents. For macro file edit permission, please contact the
local service provider.

4-18 Revision April, 2014

Chapter 4: PRG group NC300

4.12 File editing

The edit group function enables users to edit and manage G code files. After a G code
file is opened, the file explorer enters the file editing page. Point the cursor to any
location in the file, use the text, number, or edit key in the first control panel to edit as
required. After the editing is completed, switch mode, execute RESET or open other
files will automatically save the file.

See the steps described below for file editing:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) Press keys or keys to move the cursor, press

key to enter the target location in the second or third layer.

(4) Select the desired G code file, press key to open the file in edit mode.

(5) Use keys to point the cursor to any location in the

file.
(6) Use the text, number, or edit key in the first control panel to edit as required.
(7) Save the changes by performing auto save operations, including switch mode,
open other files, or press RESET.

Edit function specifications:

Edit function specifications

The maximum number of characters per 255
line
Available editing modes Edit mode
Size limit of editable files Only the file with size less than 500KB can
be edited.

Note: The edit relevant function bar displays only when entering the "edit mode" of the
file management or edit function. Otherwise, in non-edit mode, the PRG group
function provides views and coordinates information display of currently open
files only.

Revision April, 2014 4-19

NC300 Chapter 4: PRG group

4.12.1 Search by line number

This function enables users to search contents in running G code files by line number.

See the steps described below for file editing:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) Press keys or keys to move the cursor, and then

press key to enter the target location in the second or third layer.

(4) Point to the desired G code file, press key to open the file and enter the
edit mode.

(5) Press function key to select the next option page.

(6) Press key (LABEL) and the line number input dialog box (key pad 0~9)
will pop up.

(7) Enter the desired line number and press key. The cursor moves to the
given line number and finish searching.

Line number search specifications

Line number search specifications

Maximum length of searching string 62
Format of searching string Actual line number of program (key pad 0~9)

4-20 Revision April, 2014

Chapter 4: PRG group NC300

4.12.2 Search by keywords

This function enables users to search the program by keywords. Searching results
vary with the fuzziness of selected keywords.

See the steps described below for file editing:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program
menu].

(3) Press keys or keys to move the cursor, press

key to enter the target location in the second or third layer.

(4) Point to the desired G code file, press key to open the file and enter the
edit mode.

(5) Press key to select the next option page.

(6) Press key (STRING) and the keyword input dialog box will pop up.

(7) Enter the desired keywords and press key. The cursor moves to the first
location where the keyword occurred in the file.
(8) The keywords are highlighted in block and the 'Forward' and 'Backward' options
are displayed in the function bar.

(9) Press key (NEXT) to search the next match. Press key (PREV)
to search the previous match.

(10) Press key to exit the keyword search page. The function bar resumes
displaying normal file editing options.
(11) Return to the edit function bar, repeat step (6) ~ (9) to search with other
keywords.

Keyword searching specifications

Keyword searching specifications

Maximum length of keyword 63

Revision April, 2014 4-21

NC300 Chapter 4: PRG group

4.12.3 Block starting/ending point

This function simplifies file editing in case a large section of program modification is
required. Users can define a block by defining its beginning and ending point with the
cursor then edit the block with normal delete, copy and paste functions.

See the steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program
menu].

(3) Press keys or keys to move the cursor, press

key to enter the target location in the second or third layer.

(4) Point to the desired G code file, press key to open the file and enter the
edit mode.

(5) Press key (B start) to set the current cursor position as the start of the
block.

(6) Use keys to move the cursor to the desired block

end.

(7) Press key (B end) to set the current cursor position as the end of the
block. See the figure below.

Figure 4-12-1

4-22 Revision April, 2014

Chapter 4: PRG group NC300

(8) Follows step (5) ~ (7), press key (DEL) to delete text in a given block.

(9) Follows step (5) ~ (7), press key (Copy) to copy text in a given block.

Move the cursor to the desired paste area, and press key (Paste) to
paste the selected text.

4.12.4 Delete (lines and blocks)

This function deletes the entire line where the cursor is located or the block set up
earlier. It also can delete the text of the entire block with the setting of block at start and
end point.

See the steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program
menu].

(3) Press keys or keys to move the cursor, press

key to enter the target location in the second or third layer.

(4) Point to the desired G code file, press key to open the file and enter the
edit mode.

(5) Move the cursor to the line to be deleted and press key (DEL) to delete
the entire line.
(6) Delete a program block in the same way as described in Section 4-12-3. See
step (8) for defining the starting and ending points of a block.

Revision April, 2014 4-23

NC300 Chapter 4: PRG group

4.12.5 Copy and paste (line and block)

Move the cursor to the desired line, press the copy function key to the clipboard, and
paste to the selected location. This function applies to text in a given block.

See the operation steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) Press keys or keys to move the cursor, press

key to enter the target location in the second or third layer.

(4) Point to the desired G code file, press key to open the file and enter the edit
mode.

(5) Move the cursor to the desired line for copying, press key (Copy).

(6) Move the cursor to the target paste location and press key (Paste) to paste
the line.
(7) The entire block can be copied as described in Section 4-12-3. See step (9) for
defining the starting and ending points of a block.

4-24 Revision April, 2014

Chapter 4: PRG group NC300

4.12.6 Undo
Users can press the 'undo' key to cancel previous editing operations for up to seven
steps.

See the steps described below:

(1) Set the system to "Edit mode".

(2) Press key and the screen of switching group will be the [Program menu].

(3) Press keys or keys to move the cursor, press

key to enter the target location in the second or third layer.

(4) Point to the desired G code file, press key to open the file and enter the
edit mode.

(5) Press key (Undo) to undo the last editing operation.

Revision April, 2014 4-25

NC300 Chapter 4: PRG group

4.13 Other mode functions

Auto mode (AUTO):
After entering the PRG group screen, the contents of the currently opened G code file
display. The status information of the currently opened/executed file as well as the line
being executed can be viewed. The PRG group function in auto mode displays
program execution relevant information and coordinates of movements during program
running.

See the operation steps described below:

(1) Press key in "Auto mode" to display program running status in full
screen as illustrated in the figure below.

Figure 4-13-1

4-26 Revision April, 2014

Chapter 4: PRG group NC300

(2) Press key again as described above to switch to the program and
coordinates combine screen as illustrated below.

Name of current program Line being executed

Current
group
screen F.act: actual feed rate
S.act: actual spindle
speed
D: tool diameter
compensation ID
Content of H: tool length
program compensation ID
being T: tool ID
F: Feed rate
executed S: Spindle speed
t: pause time
CYC: Single
machining time

Information
of each
coordinate
being Current
executed command
status

Current
system
mode

Figure 4-13-2 Current

motion factor

The breakpoint search function in auto mode can be used to track an auto recorded
line number after program abortion (see DGN_system information for relevant
information screen). The program for tracking from cursor position to selected
searching line/sequence number employs internal fast computing and running; see the
figure below for illustration.

Figure 4-13-3

Revision April, 2014 4-27

NC300 Chapter 4: PRG group

See the operation steps described below:

(1) Press key in "Auto mode" to enter the program running screen.

(2) Press key (START) and the breakpoint search screen pops up.
(3) Based on the breakpoint line number information, enter the desired program line

or sequence number. Press key to complete the setting.

(4) Press key (RUN) to move the cursor to the re-starting line or sequence
number by internal operation.

(5) The steps before the specified line number are executed by the controller
internally with results recorded automatically. The system stops at the breakpoint
line and waits for its execution.
(6) Press "Cycle start" key to resume normal program execution.

Note:
(1) The system stops program execution when it reaches the re-start step. The
line remains unexecuted until the Cycle start is pressed and the system
resumes normal operation.
(2) Valid search formats are the line and N number of the program.
(3) During program running or after breakpoint search is defined as in program
running status, any breakpoint search request will be ignored.

The SF setup function can be used to change the feeding speed (F command) and
spindle speed (S command) during G code execution, see as Figure 4-13-4 below. After
the setting of SF and entering the new command value, the speed command is
changed.

Figure 4-13-4

4-28 Revision April, 2014

Chapter 4: PRG group NC300

See the operation steps described below:

(1) Press key to enter the program execution screen in Auto mode.

(2) Press key (SF set) and the SF command input dialog box will pop up.

(3) Enter new S or F values, press key and the speed is changed.

Note:
(1) The SF settings are valid during single execution only while the S and F
values in the G code remain intact. For a G code that requires repeated
execution, it is recommended to edit the program and ensure the accuracy of
speed commands.
(2) A revised S value will apply to the spindle speed in the G code immediately
while the F value setup applies and the new feed speed (F command) takes
effect only after new data in the system buffer is processed.
(3) Do not use this function to change the existing speed command for a G code
program without S and F commands.

JOG and hand wheel mode (JOG, MPG):

See the SF setting steps described below:

(1) In JOG mode or MPG mode, press key to enter into the program execution
screen.

(2) Press key (SF set) and the SF command input dialog box will pop up.

(3) Enter new S or F values, press key, and the speed is changed.

Users can manually move the axis to any position via Teach Programming. Function
keys of teach programming can automatically convert the coordinates value of three
axes into a motion command of one single node. It should be processed under JOG or
hand wheel mode. The function of teach programming is in PRG group, which can be
operated in existed files or new files. Functions include fast moving, linear cutting, arc
cutting, delete, create files, save files and select absolute / mechanical coordinates and
will automatically convert the file into the corresponded command format according to
different functional selection. See below for the converting format.

Revision April, 2014 4-29

NC300 Chapter 4: PRG group

Function The converted command format

Create a new G90 G40 G49 G98 G50 G64 G80 G17 G69 G21
file when teach G54 G15 S3000 M03 F1000
programming is
enabled. ※According to the parameter (unit of length), it converts to G21
or G20 command.
Rapid G00 + X_Y_Z_
Linear Cutting G01 + X_Y_Z_
Arc Cutting G02 or G03 + X_Y_Z_ + I_ J_

※According to plane X-Y, Z-X and Y-Z, it converts to G17+I_ J_,

G18+K_ I_ and G19+J_K_ respectively.
Absolute G90 G00 (or G01/G02/G03) + X_Y_Z_
Coordinate
Mechanical G53 G00 (or G01/G02/G03) + X_Y_Z_
Coordinate

See the operation steps described below:

(1) In “JOG mode” or “hand wheel mode”, press key to enter the page of
program execution.

(2) Press key (TEACH) to enter the page of teach programming.

(3) Select the file and execute program in current file or the new one. If desire to
execute program in current file, users have to open the file under “Edit Mode”.

If executing the program in new file, press key (NEW FILE). Enter the

file name in a pop-up input box. Then, press key. Users can create new
files in current directory path.
(4) Specify the data type of coordinates point. For example, select the absolute

coordinate, press the second toolbar, then press key (ABS). Or press

key (MECH) once to switch the data type as mechanical coordinates.

(5) Move the axis to the specified position in “JOG mode” or “Hand wheel mode”.

Then, press key (RAPID) or key (LINEAR) according to the

demand of motion mode, which means to insert the coordinates command at
cursor position. And the coordinates command is generated based on the data
type of its value.

4-30 Revision April, 2014

Chapter 4: PRG group NC300

(6) To continue Step (5), when it specifies arc motion, firstly press key
(ARC) to display the toolbar of acr cutting.

(7) Then, specify arc plane setting. Press key (PLANE SEL) to select
plane of X-Y, Y-Z or Z-X.
(8) Move and setup the start point, middle point and end point of the arc in

sequence. Press , , key (P1, P2 and P3). When the setting

of P3 is complete, it is automatically converted into arc cutting command. Its
direction is determined by the sequence of P1 ~ P3, either G02 or G03, and
calculate the radius value.
(9) If the coordinates command is incorrect, move the cursor to the node. Press

key (DEL) in the first layer of toolbar in teach programming to delete the
node.
(10) When complete the operation of teach programming, except the function of
auto save mechanism (RESET, system switch mode, file switch), users can

save the programming result when pressing key (SAVE).

Note:
(1) Function of teach programming has to be operated under “JOG” or “Hand
wheel” mode.
(2) The file capacity of teach programming is the same as file edit (under 500
KB).
(3) For files created by teach programming, its filename has to comply with
the standards.
(4) When continuously input two same points, the second point will be ignored so
as to avoid the ineffectiveness of motion node.
(5) P1, P2, P3 of arc command need to be setup in sequence. Their position
determines the command direction and the distance of the circle center.
(6) When the function of teach programming is enabled and no file is opened, the
system will generate a blank file named “TEACH.NC” in the directory at
cursor position (The file will be generated in root directory of CF in initial
setting). Users can directly use the function of teach programming.

Revision April, 2014 4-31

NC300 Chapter 4: PRG group

Manual mode (MDI):

The PRG group function provides simplified program entry, save, clear, and execution
functions in manual mode. See the figure below for the program editing screen. This is
exclusive to manual mode. Before the manual edited program is loaded in the system
only the cursor displays. Users can enter up to 17 lines of program steps. It is required
to load the program again before running it. Otherwise, it cannot be executed.

Figure 4-13-5

Figure 4-13-6

The file save function saves the manual edit file in the current directory with the naming
rule that described in Section 4-2. The Add file function requires giving a unique name
in the current directory and with a format compliant with this standard. The clear
function removes contents in the programming page of manual mode. It functions the
same as pressing and holds the RESET key for 3 seconds.

4-32 Revision April, 2014

Chapter 4: PRG group NC300

Note:
(1) The RESET key has two functions in manual mode. The first one is the same
as in auto mode which aborts the execution of a program and returns to the
first line of a manual entry program. The second can clear the contents in the
manual entry area by pressing and holding for 3 seconds.
(2) If the node of M30 is included, after the execution is complete, the cursor will
return to the first line and execute line display.
(3) If the node of M30 is not included, after the execution is complete, the cursor
stops at the last line and executes cursor display.
(4) If the last node of the program is M02, after the execution is complete, the
cursor stops at the last line and executes line display.

Revision April, 2014 4-33

NC300 Chapter 4: PRG group

(This page is intentionally left blank.)

4-34 Revision April, 2014

Chapter 5: OFS group NC300

Chapter 5: OFS group

The OFS group provides setup functions for workpiece setup, cutting tool's length or
diameter compensation, and variables of macros.

5.1 Coordinates setting

The coordinate system (G54~G59) provides multiple workpiece coordinates system setup
function. Together with the workpiece coordinates system (G54 ~G59) command, the G
code command not only simplifies coordinate calculation during program coding but also
enhances flexibility in changing coordinate data for machining. This data table enables
users to designate coordinate data by working together with any workpiece coordinates
system command in G54~G59 of G code as illustrated in the figure below.

Coordinates
information
Mechanical
coordinates / relative
coordinates
Coordinates system
setup
Offset coordinates /
G54~G59

Figure 5-1-1

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Coord) to enter the coordinates system setup function bar
screen.

Revision April, 2014 5-1

NC300 Chapter 5: OFS group

Note:
(a) To set up coordinates system only when no machining program is executing.
During program execution, data entry is rejected by the system.
(b) The end of execution of a single step program is defined as not in running
status while a paused program is in running status.

5.1.1 Auto setting

The auto setting function inputs the current position of each axis to the coordinates
system (G54~G59) where the cursor is. The input method includes single axis,
multiple axis and L/2. The L/2 input shall work together with the relevant axis clear
function. The auto setting function also clears the numeric values of a given
coordinates system with sub-functions of relative clear, all clear, L input, L/2 input and
P input.

The All Clear function clears all axis value of the current coordinates system to zero
while all other coordinate systems' value remains intact.

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Coord) to enter the coordinates system setup function bar
screen.

(3) Press key (Auto) to switch to the screen with the coordinates auto setup
function bar.

(4) Use keys to move the cursor to the position of

coordinate system group designation.

(5) Press key (CLR ALL) to remove all coordinates group data where the
cursor resides.

 Relative clear: Relative coordinates data corresponding to cursor position is removed

by this function. Axis types are determined by cursor position. Relative coordinates
irrelevant to the cursor remain intact. This function clears relative coordinate value in
the coordinates display rather than data of the actual workpiece coordinates system.

 L/2 input: This function sets up a coordinates system with the origin at the center of an
object. It replaces manual calculation and entry steps with the system's auto
calculations and setting. It requires an accompanying relative clearing function.

5-2 Revision April, 2014

Chapter 5: OFS group NC300

See the operation steps described below: (illustration based on X-axis)

(1) In [Jog mode] or [Hand wheel mode], move the machine axially to the initial
X-axis contact point of the workpiece.

(2) Press key to enter the [Offset menu].

(3) Press key (Coord) to enter the coordinates system setup function bar
screen.

(4) Press key (Auto) to switch to the screen with the coordinates auto setup
function bar.

(5) Use keys to move the cursor to the X-axis

coordinates column position for coordinate system group designation.

(6) Press key (CLR REL), the relative coordinates data corresponding to the
cursor position is reset to zero and the system temporarily sets this point as the
X-axis starting point of the workpiece as illustrated in the figure below.

Figure 5-1-2

(7) Move the machine axially to the X-axis contact point at the other end of the
workpiece.

(8) Press key (SET L/2) to set the X-axis center of the coordinates system at
half the axial length from the mechanical origin to the workpiece X-axis
automatically. This is now the working coordinate origin of the X-axis as
illustrated in the figure below.

Revision April, 2014 5-3

NC300 Chapter 5: OFS group

Workpiece origin
X setup
Clearing point L/2 setup point

Mechanical origin X-axis

Figure 5-1-3

 L input: This function auto inputs the current mechanical coordinates by individual axis.
When the cursor is moved to the X, Y, or Z field of the specified coordinates system,
the L input function inputs the current mechanical coordinates into the highlighted
coordinate field. This function inputs one set of axis coordinates data at one time. See
the operation steps described below:

(1) In [Jog mode] or [Hand wheel mode], move the machine axially to the initial
X-axis contact point of the workpiece.

(2) Press key to enter the [Offset menu].

(3) Press key (Coord) to enter the coordinates system setup function bar
screen.

(4) Press key (Auto) to switch to the screen with the coordinates auto setup
function bar.

(5) Use keys to move the cursor to the data position for
designating the coordinates system group and axis direction, e.g. the X-, Y-, or
Z-axis setup position.

(6) Press key (SET L) and the axis coordinates data input from highlighted
position is complete.

5-4 Revision April, 2014

Chapter 5: OFS group NC300

 Example of L input:
Example of L input (for the X-axis): Move the machine axially to the specified
coordinate position, as with the X-axis workpiece origin shown in Figure 5-1-4.

Workpiece X-axis workpiece

Origin

Workpiece length

Mechanical origin X-axis

Figure 5-1-4

The mechanical coordinate data is shown in mechanical coordinate fields of Figure 5-1-5.
Move the cursor to the desired coordinate group as with the G56 group in Figure 5-1-5,
press F3 key (SET L), and then the X-axis data of the mechanical coordinate is inputted to
the X-axis fields of the G56 coordinate group automatically. The single axis data input of the
coordinate group is now completed.

Figure 5-1-5

Revision April, 2014 5-5

NC300 Chapter 5: OFS group

 P input: This function inputs the coordinate center of multiple axes concurrently after
the workpiece center point is calibrated. With P input function, more than one axis,
including X, Y, Z can be inputted.
See the operation steps described below:

(1) In [Jog mode] or [Hand wheel mode], move the machine axially to the initial
X-axis contact point of the workpiece.

(2) Press key to enter the [Offset menu].

(3) Press key (Coord) to enter the coordinates system setup function bar
screen.

(4) Press key (Auto) to switch to the screen with the coordinates auto setup
function bar.

(5) Use keys to move the cursor to the data position for
the coordinates system group.

(6) Press key (SET P), multiple axis data is now automatically inputted into
the highlighted coordinate group fields.

Note: Do not clear axis coordinates values by pressing the All Clear function key after
coordinate of other axes have been setup as this may erase coordinates data
that does not desire to delete.

5-6 Revision April, 2014

Chapter 5: OFS group NC300

 Example of P input:
Move the machine axially to the specified coordinate position, e.g. the workpiece origin
in Figure 5-1-6. (Figure 5-1-6 indicates the relative position of the X- and Y-axis but not
the Z-axis.)

Y-axis Workpiece origin

Workpiece

Mechanical origin
X-axis

Figure 5-1-6

After the workpiece origin is calibrated, the mechanical coordinate data is shown in the
mechanical coordinate fields in Figure 5-1-7. Move the cursor to point to the desired
coordinates group (e.g. the G56 group in Figure 5-1-7). Press F5 key (SET P), and then the
X-, Y-, and Z-axis data of the mechanical coordinate are inputted to the mechanical
coordinate fields of the G56 coordinates group. That is, the multiple axis data input for the
axis group is completed.

Figure 5-1-7

Revision April, 2014 5-7

NC300 Chapter 5: OFS group

5.1.2 Absolute input

The coordinates system value can be inputted manually by absolute or incremental
value setups. This section explains the steps for absolute input.

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Coord) to enter the coordinates system setup function bar
screen.

(3) Use keys to move the cursor to the X-, Y-, and
Z-axis setup positions for coordinates system designation.

(4) Input positive or negative values by pressing keys - . To input a

negative value, press key in advance. Press key to confirm the

unit of values.

(5) Press key (ABS) to enter the value of the coordinate axis.

Note:
(a) The unit of value is mm. Value without decimal points is in unit of μm. That is,
input value 123456 indicates 123.456 mm.
(b) The absolute input can be made by step (5) as described above or by
pressing the ENTER key.

5-8 Revision April, 2014

Chapter 5: OFS group NC300

 Example of absolute input:

Move the tool center from mechanical origin to the X and Y position of mechanical
origin, then register the coordinates data of X and Y in the coordinates system setup
function (G54~G59) of the controller's OFS group. Finally, run the relevant workpiece
coordinates system command in the G code program to assign workpiece coordinates
system origin setup.

Workpiece

Figure 5-1-8

Figure 5-1-9

Revision April, 2014 5-9

NC300 Chapter 5: OFS group

5.1.3 Incremental input

This is one of the two manual coordinates system numeric data input methods. This
function is suitable for fine tuning values entered by incremental input. For example, for
original value = 150.000 with an incremental input of 5.000, the new value shall be
155.000.

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Coord) to enter the coordinates system setup function bar
screen.

(3) Use keys to move the cursor to the X, Y, Z axis

setup position for coordinates system designation.

(4) Input positive or negative values by pressing keys - . To input a

negative value, press key in advance. Press key to confirm the

unit of value.

(5) Press key (INC) to increase or decrease the coordinate axis position
depending on whether the value is greater or less than zero.

Note:
(a) Ensure the accuracy of the input value and method when setting up
coordinate values manually as the risks of invalid movement position caused
by invalid coordinate values are very big.

5-10 Revision April, 2014

Chapter 5: OFS group NC300

5.1.4 Rectangle center

This function assists users in setting up coordinate data of the center of a rectangle
object with a rectangle drawing as shown in the figure below. The system converts data
of the four corner points into coordinate data of the object's actual center as illustrated
in the figure below.

Figure 5-1-10

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Coord) to enter the coordinates system setup function bar
screen.

(3) Use keys to move the cursor to data fields for

coordinates system designation.

(4) Press key (SQUARE) to enter the rectangle center page.

Revision April, 2014 5-11

NC300 Chapter 5: OFS group

(5) As guided by the rectangle shown in the screen, move the spindle center to the

mechanical position of X1, X2, Y1, Y2, press (X1,

X2, Y1, Y2) keys to set up the coordinates data of each point.

(6) Press key (Set) after coordinates of the four points are set, the system
determines the coordinate data of the rectangle center and inputs the data to the
coordinates system.

(7) Set up coordinate position by moving the Z-axis, press key (SET Z) to
set up the Z-axis coordinates of the workpiece coordinates group.

5-12 Revision April, 2014

Chapter 5: OFS group NC300

 Example of rectangle center:

Assign fields of coordinates group. Manually move the spindle to the four corners of
the object, input the X and Y coordinates of these 4 points as shown in Figure 5-1-11.

Figure 5-1-11

After the coordinates of the four rectangle corner points are set, press F5 key (Set); the
system then takes out the actual mechanical coordinates value of the rectangle object
center and sets up given coordinates system data as shown in Figure 5-1-12.

Figure 5-1-12

Revision April, 2014 5-13

NC300 Chapter 5: OFS group

5.1.5 Circle center

This function sets up the coordinates data of the center of any ball matter. Select any 3
points on the ball object and set up their coordinates data; the circle center function
can determine the coordinates of the object center as shown in the figure below:

Figure 5-1-13
See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Coord) to enter the coordinates system setup function bar
screen.

(3) Use keys to move the cursor to data fields for

coordinates system designation.

(4) Press key (CIRCLE) to enter the circle center page.

(5) Move the mechanical position of P1, P2, P3 as guided, press

(P1, P2, P3) keys to set them up one by one.

(6) After setting up coordinates of the three points on a circle, press key (Set);
the system then determines the coordinates data of the circle center and inputs
the data to the coordinates system.

(7) Set up coordinate position by moving the Z-axis, press key (SET Z) to set
up the Z-axis coordinates of the workpiece coordinates group.

5-14 Revision April, 2014

Chapter 5: OFS group NC300

 Example of circle center

This function applies to any workpiece in ball shape. Manually move the spindle to
access any three outer points on the circle, and then set up the coordinate value of
these three points by relevant function keys as shown in Figure 5-1-14.

Figure 5-1-14

After the coordinates of any three outer points are set, press F4 key (Set), the system then
takes out the actual mechanical coordinates value of the circle center and sets up given
coordinates system data as shown in Figure 5-1-15.

Figure 5-1-15

Revision April, 2014 5-15

NC300 Chapter 5: OFS group

5.2 Tool register

This function varies with tool length compensation (G43 or G44, or cancel command
G49) or diameter compensation (G41 or G42, or cancel command G40). The tool
register function covers tool length compensation, diameter compensation, length
wear compensation, diameter wear compensation, and tool life span management
functions.
The data fields correspond to H (tool length compensation) and D (tool diameter
compensation) codes assigned by the machining program. The tool register settings
can assign tool length or tool diameter fields data to meet a given machining path and
size without program modifications. The numeric data setup covers absolute input,
incremental input, H setup, and data clearance functions. See the figure below for the
tool compensation function screen.

Figure 5-2-1

Range of tool register values

Input range of tool length data -2000.0 ~ 2000.0 mm
Input range of tool diameter data -150.0 ~ 150.0 mm
Input range of tool length wear -2000.0 ~ 2000.0 mm
compensation data
Input range of tool diameter wear -150.0 ~ 150.0 mm
compensation data
Input range of tool life span 0 ~ 99999999 serves

5-16 Revision April, 2014

Chapter 5: OFS group NC300

 Absolute input: This is one of the manual data input methods. Use this function to
input absolute values of tool length, tool diameter, wear compensation or tool life span
data. Press ENTER key to do absolute value input.

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (CUTTER) to enter the screen with the tool register function
bar.

(3) Use keys to move the cursor to data fields for tool
length, diameter, wear, or life span designation.

(4) Input positive or negative values by pressing keys - . To input a

negative value, press key in advance. Press key before entering

the tool compensation data to ensure the unit of value. Only positive integers are
valid input for tool life span.

(5) Press key (ABS) to register absolute values.

Note:
The tool data fields are for individual compensation values. For example, when
the length fields are highlighted, then the input data are for tool length
compensation values.

Revision April, 2014 5-17

NC300 Chapter 5: OFS group

 Incremental input: This is one of the manual data input methods. Use this function to
input incremental values of tool length, tool diameter, wear compensation or tool life
span data.

See the operation steps described below for incremental input:

(1) Press key to enter the [Offset menu].

(2) Press key (CUTTER) to enter the screen with the tool register function
bar.

(3) Use keys to move the cursor to data fields for tool
length, diameter, wear, or life span designation.

(4) Input positive or negative values by pressing keys - . To input a

negative value, press key in advance. Press key before entering

the tool compensation data to ensure the unit of value. Only positive integers are
valid input for tool life span.

(5) Press key (INC) to register incremental values.

5-18 Revision April, 2014

Chapter 5: OFS group NC300

 H setup: This function auto inputs the Z-axis height of current mechanical coordinates
in assigned tool length compensation data (H) exclusively. It has merit in that it can
prevent input error during manual setup by users as well as reduce the time required
for value setup.

See the operation steps described below:

(1) In [Jog mode] or [Hand wheel mode], move the Z-axis to given coordinates
height.

(2) Press key to enter the [Offset menu].

(3) Press key (CUTTER) to enter the screen with the tool register function
bar.

(4) Use keys to move the cursor to the tool length fields
for tool code designation.

(5) Press key (SET H) to set the coordinates of the current Z-axis mechanical
coordinates value to given data fields.

Note:
(a) The H setup function applies to tool length data fields only.
(b) Do not change values in OFS group during program execution. Enter values
only when the program stops. The program stop status includes the program
is fully not in operation, a single step initiated single step is completed, and
after the RESET key is pressed.
(c) The length wear value is reset to zero when inputting tool length value with H
setup.

Revision April, 2014 5-19

NC300 Chapter 5: OFS group

 Clear: This function clears tool compensation values with options of geometry, wear,
life span, and all clear.

Geometry clear: clear all tool length and diameter values.

Wear clear: clear all tool length compensation and diameter compensation values.
Life span clear: clear all tool life span values.
All clear: clear all tool registry data.

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (CUTTER) to enter the screen with tool register function bar.

(3) Press key (Clear) to enter the clear function bar display.

(4) Press key (H/D) to clear tool length and diameter values. Press
key (Wear) to clear all tool length compensation and diameter compensation

values. Press key (Life) to clear all tool life span values. Press
key (All) to clear all tool registry data.

5-20 Revision April, 2014

Chapter 5: OFS group NC300

5.3 Tool magazine register

This function manages tool positions the relative tool magazine code after tool
exchanges. The tool magazine data is a table recording the actual tool pot positions
and tool ID of the current machine. It not only records and displays the tool pot position
of individual tools but also changes the tool sequence in tool magazine data fields with
proper permission. This enhances the tool magazine management function by
parameter settings.
The tool magazine register function can run in Jog mode only as shown in the
figure below.
Name of current Line being
program executed

Current
group
screen Tool magazine
system number

Current
command tool
ID

Current standby
ID
The sequential
status of tool ID
Current standby
tool pot ID

Spindle tool ID

Tool ID input field

Each current motion
Figure 5-3-1 rate

See the operation steps described below for tool magazine setup:

(1) Set the system to "Jog mode".

(2) Press key to enter the [Offset menu].

(3) Press key (MAGA) to enter the tool magazine data setup function screen.

(4) Use keys to move the cursor to assigned data fields.

(5) Enter newly changed tool ID, press key (Set) (or press key) to set up
new tool magazine position.

Revision April, 2014 5-21

NC300 Chapter 5: OFS group

 Example of tool ID exchange:

If the assigned tool ID duplicates one in existence, then it exchanges it with the one at
the original place automatically. This ensures that each tool ID in the tool magazine
does not duplicate another and prevents incorrect tool calling.

5-22 Revision April, 2014

Chapter 5: OFS group NC300

 Operation description:
Figure 5-3-2: initial status of the tool magazine with tools in it in numeric sequence
Figure 5-3-3: set position 1 = 2, and tools ID 1 and 2 in tool magazine 1 and 2
exchanges with each other.
Figure 5-3-4: set position 3 = 5, and tools ID 3 and 5 in tool magazine 3 and 5
exchanges with each other.

This demonstrates that tool IDs in the tool magazine exchange with each other after the tool
ID of a given tool magazine number is changed. This eliminates errors caused by invalid
tool ID accessing.

 All reset: The tool register option also provides the tool magazine position reset
function. This resets the tool ID in the tool magazine to its initial default, i.e. both tool
magazine and tool ID are in numeric sequence. This function resets the tool magazine
tool ID to its original value for tool ID misplacement troubleshooting or tool ID reset.

See the operation steps described below:

(1) Set the system to "Jog mode".

(2) Press key to enter the [Offset menu].

(3) Press key (MAGA) to enter the tool magazine data setup function screen.

(4) Press key (RST ALL) to reset all tool magazine position records.

 Tool magazine block: This function blocks the tool magazine position not used by the
program. Tools in a blocked tool magazine position cannot be called. If they are called
incorrectly, the system blocks their use, warns with an error message, and halts
program execution. This provides one more protection mechanism against errors
caused by incorrect tool calling. For example, users can block a tool magazine position
with damaged positioning latch or that might interfere with adjacent large diameter
tools. A blocked tool magazine position is identified by a different color.

See the operation steps described below:

(1) Set the system to Jog mode.

(2) Press key to enter the Offset menu.

(3) Press key (MAGA) to enter the tool magazine data setup function
screen.

(4) Use keys to move the cursor to tool magazine

designation data fields.
Revision April, 2014 5-23
NC300 Chapter 5: OFS group

(5) Press key (LOCK) to block the tool magazine position as shown in
Figure 5-3-5.

Figure 5-3-5

To unblock the tool magazine, continue with the steps described below:

(6) In the tool magazine setup screen press keys to

move the cursor to blocked fields.

(7) Input the specified tool ID, press to unblock the tool magazine position.

5-24 Revision April, 2014

Chapter 5: OFS group NC300

 Example of tool magazine block:

Use this function to block a tool magazine adjacent to one that has a large diameter
tool. Blocking these two tool magazines can stop the operation of an improper tool ID
calling program and protects tools from colliding with large-diameter tools in
neighboring tool magazine.

Figure 5-3-6

When T1 holds a large diameter

tool, it may interfere with adjacent
tools as shown in the figure to the
left. Once blocked by this function,
the T2 and T16 tool magazine
positions cannot be called any more.

Figure 5-3-7

Revision April, 2014 5-25

NC300 Chapter 5: OFS group

※ Multi tool magazines management function

 For applications that require multiple tool magazine management systems, users may
open the multi tool magazine management function through the tool magazine
parameter once properly permitted. Users may assign a different number of tool pots
for each tool magazine as well as the corresponding tool ID. The [Tool Magazine 1 and
2] function bars are used for managing tool ID in either tool magazine system. Please
contact an equipment dealer/service provider for multi tool magazine relevant
functions.

Figure 5-3-8

Note:
(a) The tool magazine ID can be set up in "Jog mode" (JOG) only. The tool
magazine setup option is hidden in other modes.
(b) The special user permission is a must to do tool magazine ID setup or reset.
(c) Tool ID in one tool magazine cannot duplicate another. If the assigned tool ID
duplicates one in existence, then it exchanges it with the one at the original
place automatically. This ensures that each tool ID in the tool magazine does
not duplicate another and prevents incorrect tool calling.
(d) When the spindle's initial tool ID is set to T0, once T0 is placed in one tool
magazine, that tool magazine is recorded as the position of T0 and cannot be
blocked. When the field of tool magazine is T0, it is not allowed to block and
the message "Tool ID Tool magazine cannot be blocked" will pop up.

5-26 Revision April, 2014

Chapter 5: OFS group NC300

5.4 Macro variable

Use variable input setup of this function along with variable command for various MLC
data I/O, condition computing, and controls. The macro variable function covers local,
global, retaining variables and expanded variables with values in double precision
format.

Figure 5-4

5.4.1 Local variable

Local variables are used by the macro program in the local area and are numbered
from 1~50.

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Macro) to enter the variable value entry screen.

(3) Press key (Local) to enter the entry screen for field ID starting with
number 1.

(4) Use keys to move the cursor to the desired variable

data field.

(5) Enter variable settings, press key to complete the setting.

Revision April, 2014 5-27

NC300 Chapter 5: OFS group

5.4.2 Global variable

Global variables are variables shared by the main programs, sub routines, and macro
program and are numbered from 51~250.

See the operation steps described below:

(1) Press key to enter the [Offset menu].

(2) Press key (Macro) to enter the variable value entry screen.

(3) Press key (Global) to enter the entry screen for field ID starting with
number 51.

(4) Use keys to move the cursor to the desired variable

data field.

(5) Enter variable settings and press key to complete the setting.

5.4.3 Retaining variable

These variables maintain system specific status data after power outage and are
numbered from 1601~1800.

See the operation steps described below:

(1) Press key to enter the Offset menu.

(2) Press key (Macro) to enter the variable value entry screen.

(3) Press key (Hold) to enter the entry screen for field ID started with number
1601.

(4) Use keys to move the cursor to the desired variable

data field.

(5) Enter variable settings and press key to complete the setting.

5-28 Revision April, 2014

Chapter 5: OFS group NC300

5.4.4 Expanded Variable

500 expanded variables can be used in the system. Its range is between 10001
and 10500.

See the operation steps described below:

(1) Press key to enter【Offset】.

(2) Press key (MACRO) to the variable value entry screen.

(3) Press key (EXPAND). The screen jumps to the entry screen beginning
with 10001.

(4) Use keys to move the cursor to the desired variable

data field.

(5) Enter variable settings and press key to complete the setting.

Revision April, 2014 5-29

NC300 Chapter 5: OFS group

(This page is intentionally left blank.)

5-30 Revision April, 2014

Chapter 6: GRA group NC300

Chapter 6: GRA group

The GRA group function displays trails during program running to help in ensuring
correctness of the G code operation. It enables users to preview the cutting graph and
perform simulation on current files. Its function also includes G code format examination
and processing review. The initial screen of GRA group is determined by the setting value
of parameters. See figure 6-0-1 or 6-0-2.

Figure 6-0-1

Figure 6-0-2

Revision April, 2014 6-1

NC300 Chapter 6: GRA group

6.1 Cutting Path

When executing machining program, the screen will be switched to GRA group. It will
draw the motion tracking of the current program in GRA screen. When it is used for
machining, this function can help to check if the cutting path matches to the machining
mission. The motion tracking will be drawn when it executes machining program. And
X-Y, Y-Z, X-Z as well as X-Y-Z plane movement tracking will be provided. This also
includes the function of zoom in, zoom out and direction display when moving graphs.
Use graph parameter 14003 to setup the display mode. Setup the positive position
according to the machine type. When activating the preview of cutting path, the
function of previewing cutting graph cannot be enabled.

See the operation steps described below:

(1) Press key to enter【graph function】page.

(2) Press key (CUTTING PATH) to the graphic display function.

(3) Press key (X—Y) to switch the screen as X-Y; or press key again

to swtich the screen as Y-Z; or press key again to switch the screen as

X-Z; or press key again to switch the screen as X-Y-Z plane movement
trail.
(4) When machining program is executing, entering GRA group will start drawing.

Press key (STOP DRAW) to stop the drawing funciton of cutting path.

Press key (DRAW) to continue the drawing.

(5) Press key (CENTER) to move the current motion to the center of graphic

display. Press key (ZOOM IN) or (ZOOM OUT) to magnify or

minimize the display.

(6) The cutting graph could be moved by (UP), (DOWN),

(LEFT) and (RIGHT) keys.

6-2 Revision April, 2014

Chapter 6: GRA group NC300

6.2 Cutting Preview

This function is to preview the graph of cutting path. Before actual cutting, it can check
if the format of G code is correct. It also can preview the cutting graph without actually
operate the machine tools. The cutting preview displays the visual angle of X-Y, Y-Z,
X-Z and X-Y-Z. Zoom in/out display and the display of graph moving direction are
included as well. The related parameters are the same as described in section 6.1.
When enabling function of cutting preview, it cannot execute the actual cutting.
Function of displaying cutting path and cutting preview cannot be activated at the same
time. When enabling the function of cutting path, please cancel the preview or press
RESET key.

See the operation steps described below:

(1) Press key to enter the [graph function] page.

(2) Press key (PREVIEW) to enter the display function of cutting preview.

(3) Press key (X-Y plane) to switch the screen as X-Y; or press key

again to switch to Y-Z; or press key again to switch to X-Z; or press

key again to switch the screen to X-Y-Z plane movement motion tracking.

(4) Press key (PREVIEW) to view the cutting result of G code file. Press

key (CANCEL PREVIEW) to stop preview.

(5) Press key (CENTER) to move the single node to the center of graphic

display. Press key (ZOOM IN) or (ZOOM OUT) to display the

graph.

(6) Use (UP), (DOWN), (LEFT) and (RIGHT) keys in

toolbar of the next page to move the cutting graph.

Note:
(a) When activating the display of cutting path, function of previewing cutting
graph cannot be enabled.
(b) When cutting preview is enabled, it must not operate the actual cutting.
Function of previewing cutting path and cutting preview cannot be
activated at the same time, before enabling cutting path, please cancel the
preview or press RESET key.
Revision April, 2014 6-3
NC300 Chapter 6: GRA group

(c) During cutting preview, switch the mode will force the preview function to
be cancelled.
(d) If the preview is cancelled, it starts to preview from the node when
enabling the function again.
(e) The cutting path and graph of cutting preview might exceed the frame
because of the setting of machine coordinates. When it starts drawing or
activates the preview, if users find no path or graph displays inside the
frame, please press the “Center Set” key to move the current tracking to
the center of the frame.

6-4 Revision April, 2014

Chapter 7: ALM group NC300

Chapter 7: ALM group

The system prompts an alarm message for any program execution or command format
error. The ALM group function displays current alarms sent by the system to help users in
program debugging. It also features an alarm message log function.

7.1 Alarm
It is required to troubleshoot the issue that caused the alarm then press the RESET
key to reset the system back to initial status. See the figure below for the alarm display
screen with marked alert area.

Figure 7-1-1

See the steps described below for the alarm message display and clear:

(1) Press key to enter the [alarm function] page.

(2) Press key (Alarm) to enter the current alarm message screen.

(3) Use key to clear the alarm message now shown on the screen.

Revision April, 2014 7-1

NC300 Chapter 7: ALM group

7.2 Message log

This function records alarms and alarm process data generated by the system. Users
may review all errors during program execution by sequence of alarm time and type for
troubleshooting and analysis. Data contained in each alarm record covers the time and
name of alarm.
The alarm history can contain up to 512 records. In addition to viewing them, all can be
deleted as shown in the figure below.

Figure 7-2-1

See the steps described below to clear all alarm history:

(1) Press key to enter the [alarm function] page.

(2) Press key (History) to enter the alarm history page.

(3) Press key (CLR ALL) and the confirmation dialog box will pop up.

(4) Press "Y" (yes) key then press key and all alarm records are removed.

Note: The system switches to ALM group screen whenever there is error occurred.
Users can also set up parameter 10016 (The popup screen when an alarm occurs).
The system will not switch to ALM screen automatically when an alarm occurs.

7-2 Revision April, 2014

Chapter 8: DGN group NC300

Chapter 8: DGN group

The DGN group provides machining information, user variable, system monitoring, gain
adjustment, and system interface functions to optimize the system. MLC diagnostics
function is also provided for system to do MLC status monitoring or forced device ON/OFF,
and password setup function for permission management. With this function, various
system parameters can be imported / exported.

8.1 Machining information

This function sets up a number of machined and target machining workpieces. It also
resets the time and count of machined pieces and target ones. See the figure below for
the machining information page:

Figure 8-1-1

See the operation steps described below for machining information setup:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PROCESS) to enter the machining information page.

Revision April, 2014 8-1

NC300 Chapter 8: DGN group

(3) Press key (Set NR) to pop up the machining count setup screen as
shown in the figure below.

Figure 8-1-2

(4) Use keys to point to the desired field.

(5) Enter value in range of 0～9999 and press key to complete the setting.

Users can use the machining information function to reset the machining time and
count data of the system as of now. See the operation steps described below for
machining time clearing:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PROCESS) to enter the machining information page.

(3) Press key (CLR TIME) and the confirmation dialog box will pop up.

(4) Press "Y" (Yes) key and press to reset the time of a single piece
workpiece machining time.

8-2 Revision April, 2014

Chapter 8: DGN group NC300

See the operation steps described below for machining count clearing:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PROCESS) to enter the machining information page.

(3) Press key (CLR NR) to pop up the confirmation dialog box.

(4) Press "Y" (Yes) key and press to reset the count of workpieces that
have been machined.

Revision April, 2014 8-3

NC300 Chapter 8: DGN group

8.2 User variable

Function of user variable includes system variable and user variable. System variable
is for monitoring the specific variable. And user variable enables users to update and
display device data in the embedded registers (range D512 ~ D1023). By displaying
device types in registers users may change and monitor settings in the registers (D512
~ D1023) for easier relevant devices control.

Figure 8-2-1
See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press (User VAR) key to enter the page of variable monitoring.

(3) Press (User VAR) key to enter the setup page.

(4) Use or keys to point to the desired data field.

(5) Enter the desired register number (D512~D1023), press key to display
device data of the register.

(6) Point to desired register data field, enter the appropriate value, press
key to set up device of the register.

(7) Use (US DEC), (HEX), (S DEC) or (FLOAT) to

select the display format.

(8) Point to the desired register data field, press key (DEL) to delete data
in the register.

8-4 Revision April, 2014

Chapter 8: DGN group NC300

8.3 MLC
The MLC diagnostics function displays current status of each MLC device for
monitoring and forced ON/OFF. This not only helps in inspecting system status or
driving MLC device but also provides MLC editing function as shown in Figure 8-3-1.
The MLC diagnostics function covers bit device status, register status, device
monitoring, MLC status operation and MLC editing function. See the sections below for
operation steps.

Figure 8-3-1

Revision April, 2014 8-5

NC300 Chapter 8: DGN group

8.3.1 Bit
MLC programs use many device commands to trigger ON/OFF operation. Status of
these devices can be seen in this function screen. The bit function displays bit type
device of MLC, searches devices, and forces ON/OFF operation.

See the operation steps described below: (illustrated with M device)

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (Bit) to enter the bit device status display.

(4) Press key (M) to switch to device M status display as shown in figure
below.

Figure 8-3-2

Point to or search for the desired device field with the steps (1) ~ (4). See step (5) for
device searching.

(5) Enter the device name (e.g. 107), press key (M) to point to the desired
device (M107).

8-6 Revision April, 2014

Chapter 8: DGN group NC300

The device status can be changed only when the system is in "NON-auto" mode.
See step (6) for forced ON/OFF operation.

(6) Select the device for the desired status change, press "1" and press key

to force it ON (if it is in OFF status) or press "0" and press key to force it
OFF (if it is in ON status) .

8.3.2 Register
Please refer to Section 8-3-1. As most system functions are triggered by MLC
program, the MLC device features both bit and word type devices. This section
explains operation on word type devices.

See the operation steps described below: (illustrated with register T)

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (REG) to enter the register device display.

Figure 8-3-3

(4) Press key (T) to enter the register T value setup page.

(5) Enter the device name (e.g. "10"), press key to search device T10.
Revision April, 2014 8-7
NC300 Chapter 8: DGN group

(6) Switch to the function bar in the last page. Use (US DEC), (HEX),

(S DEC) or (FLOAT) to select the display format.

(7) Enter the setting value in the input column and press key.

8-8 Revision April, 2014

Chapter 8: DGN group NC300

8.3.3 Device monitoring

This function sets up monitoring functions for up to 45 devices.
See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (DEV MON) to enter the device name entry screen as shown
in figure 8-3-4.

Figure 8-3-4

(4) Enter the device name to be monitored as shown in figure 8-3-5. Up to 45

monitoring data entries can be set.

Figure 8-3-5

Revision April, 2014 8-9

NC300 Chapter 8: DGN group

Device: Enter the name of device to be monitored in the highlighted field.

Value: Set up device status in the highlighted field.
Status: Enter digit 0 or 1 to set device status.

Different numeral systems can be used to switch between views of user settings
including signed or unsigned decimal, hexadecimal numeral and floating point
numerals. See Figure 8-3-6 for hexadecimal conversion and Figure 8-3-7 for
floating point display.

Figure 8-3-6

Figure 8-3-7

8-10 Revision April, 2014

Chapter 8: DGN group NC300

8.3.4 Search line

Most system functions rely on devices triggered by some MLC programs which are
basically a set of command lines. This function enables users to search a program by
line number.

See the operation steps described below for searching a desired line in a MLC
program.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Enter the desired MLC program line number, press key (JUMP TO) to go
to the desired line.

8.3.5 Editor
The edit function in DGN group can manage and edit MLC program. Its operation
interface enables users to edit the MLC program directly. This function can be run in
"Edit mode" only.

I. Basic MLC command

A basic MLC command (including: LD, LDI, LDP, LDF, OUT, APP, —, ︱, INV) can
be created with the functions described in this section. See Figure 8-3-3 for
illustration.

Figure 8-3-8

Revision April, 2014 8-11

NC300 Chapter 8: DGN group

See the operation steps described below for command LD:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (EDITOR) to enter the MLC program editor screen as shown in
Figure 8-3-6.

(4) Use keys to move the cursor to the desired edit

place.

(5) Enter device name, press key (LD) and the device is created
successfully.

The steps described above apply to the creation of basic commands LDI, LDP, LDF,
OUT, APP while step (1)~(4) apply to commands "—" and "︱". Then, use the
corresponding function key to complete the command as described above.

The labeling function in MLC program is used to divide the section of the program and
can be set in MLC program.
To assign form values for basic commands, please press the form function key to enter
the setup page as shown in the figure below.

Figure 8-3-9

8-12 Revision April, 2014

Chapter 8: DGN group NC300

II. Editing (cut, copy, and paste)

This is an MLC exclusive editing function. Users can use it for single line delete,
cut, or copy or do the same to the MLC device command by circling. After an MLC
program is edited, load it for compiling and saving.

See the operation steps described below for the MLC editing function:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (EDITOR) to enter the MLC program editing page as shown in
Figure 8-3-6.

(4) Use keys to move the cursor to the desired edit

place.

(5) Press key repeatedly to point to the last row of the function page in this
layer.

(6) Select the desired function key, such as (CUT) to edit the selected line as
required.

For MLC program editing, please press the relevant function key. Available
functions are: circle, delete, cut, copy, paste, insert and delete line.

III. Symbol
This function enables users to search, delete, copy, and paste various types of
devices. Available MLC program devices are represented by symbols: X, Y, M, A,
T, C, D, P and I.

See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (EDITOR) to enter the MLC program editing screen as shown
in Figure 8-3-6.

(4) Use keys to move the cursor to the desired edit

place.
Revision April, 2014 8-13
NC300 Chapter 8: DGN group

(5) Press key to switch the function bar to the third row of the function page
in this layer.

(6) Press key (SYMBOL) to enter the device symbol function bar display.

(7) Select the device type specific function key (e.g. Device X). Press key
(X) to enter X device specific list and do delete, copy or paste function as
desired.

The same operation steps (Section III: Symbol) apply to other symbols.

IV. MLC load, import, and export

After a MLC program is edited, it is required to save it for re-compiling. The
function of saving includes compile and save. Then, users should re-start the
system to update the MLC program. Import and export MLC files can be done by
using proper function key.

8.3.6 Operation
The MLC program starts running automatically after the system is power on. The
operation function can be used to manually switch the MLC program's running. That is,
it manually switches MLC running status from ON to OFF and vice versa. This is
usually used for testing or inspecting system's MLC devices.

See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (SET) to enter the MLC execution status screen.

(4) Press key (RUN/STOP) to switch execution status of MLC program.

Note:
The status information can be viewed when "MLC stops" after the MLC program
execution is halted.

8-14 Revision April, 2014

Chapter 8: DGN group NC300

The function option can be used to force ON or OFF a MLC device.

See the operation steps described below for forced ON:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (SET) to enter the MLC execution status screen.

(4) Use keys to point to a desired device position.

(5) Press key (ON) to switch on a device.

See the operation steps described below for forced OFF:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (MLC) to enter the sub menu of MLC diagnostics.

(3) Press key (SET) to enter the MLC execution status screen.

(4) Use keys to point to the desired device position.

(5) Press key (OFF) to switch off the device.

Revision April, 2014 8-15

NC300 Chapter 8: DGN group

8.4 System monitoring

Computing results of the system can be displayed by type with this function.

8.4.1 Variable
System variables: VS0 ~ VS31 and VS100 ~ VS131.
See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (SYS MONI) to enter the system monitoring function screen.

(3) Press key (VAR MONI) to display the variable monitoring screen.

(4) Press key (SYS VAR) to enter the system variable monitoring screen.

(5) Use keys to scroll to the screen containing the desired variable
item or;

(6) enter the full name of the desired system variable and press key or enter

the variable code and press key (SYS VAR) to search the desired system
variable screen.

Figure 8-4-1

8-16 Revision April, 2014

Chapter 8: DGN group NC300

Channel variable: VC0~VC31, VC100~VC131 and VC200~VC231.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (SYS MONI) to enter the system monitoring function screen.

(3) Press key (VAR MONI) to enter the variable monitoring screen.

(4) Press key (CH VAR) to enter the channel monitoring screen.

(5) Use keys to scroll the screen containing desired variable item or;

(6) enter the full name of the desired system variable and press key or enter

the variable code and press key (CH VAR) to search the desired channel
monitoring screen.

Axis variable: VA0~VC31, VA100~VA131 and VA200~VA231.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (SYS MONI) to enter the system monitoring function screen.

(3) Press key (VAR MONI) to enter the variable monitoring screen.

(4) Press key (AXIS VAR) to enter the axis variable monitoring screen.

(5) Use keys to scroll the screen containing the desired variable item
or;

(6) enter the full name of the desired system variable and press key or enter

the variable code and press key (AXIS VAR) to search the desired axis
variable screen.

Revision April, 2014 8-17

NC300 Chapter 8: DGN group

Interface variable: VH0~VH31, VH200~VH231 and VH400~VH431 and

VH800~VH863.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (SYS MONI) to enter the system monitoring function screen.

(3) Press key (VAR MONI) to enter the variable monitoring screen.

(4) Press key (IF VAR) to enter the interface variable monitoring screen.

(5) Use keys to scroll the screen containing the desired variable item
or;

(6) enter the full name of the desired system variable and press key or enter

the variable code and press key (IF VAR) to search the desired interface
variable screen.

Use different numeral systems to switch between views of user settings including
signed or unsigned numeral system, binary system and hexadecimal numeral.

8-18 Revision April, 2014

Chapter 8: DGN group NC300

8.4.2 I/O monitoring

NC300 system can add an external device control switch through its I/O expansion
module. Users can monitor the status of the expansion control panel connected to the
I/O port.
See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (SYS MONI) to enter the system monitoring function screen.

(3) Press key (I/O MONI) to enter the status monitoring screen for the I/O
expansion module.

Revision April, 2014 8-19

NC300 Chapter 8: DGN group

8.4.3 Servo monitoring

This function enables users to monitor the status of the servo drive including channel
ports and servo status. It provides the current status of the servo drive connected to
the system as shown in Figure 8-4-2. Here, the servo of axes Y, Z, A and the spindle
are all in OFF status and only the X-axis remains in ON status.

Figure 8-4-2

See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (SYS MONI) to enter the system monitoring screen.

(3) Press key (SERVO) to enter the servo monitoring screen.

8-20 Revision April, 2014

Chapter 8: DGN group NC300

8.5 Password setting

This function enables users to set up different level of permissions for the system
(system maintenance), equipment (mechanical equipment) and users (operation and
use). It prevents unauthorized users from changing system settings.

8.5.1 System permission

The system permission function covers permission lock and permission unlock. The
password is composed of up to four alphanumeric characters (symbols excluded).

See the operation steps described below for permission lock and unlock:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (S SCP) to enter the system permission lock/unlock function
bar.

(4) If the system permission is unlocked, press key (LOCK) to lock system
permission when it is in revoked status.

(5) If the system permission is locked, press key (UNLOCK) and an entry
dialog box pops up for users to enter permission password.

(6) Enter a valid password, press key and the permission is revoked.

Revision April, 2014 8-21

NC300 Chapter 8: DGN group

8.5.2 Equipment permission

This function covers password change, permission lock, permission unlock, user 1
reset and user 2 reset. The password is composed of up to four alphanumeric
characters (symbols excluded).

See the operation steps described below for changing equipment permissions:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (M SCP) to enter the equipment permission function bar.

(4) Press key (PWD CHG) and an entry dialog box pops up as shown in
Figure 8-5-1. Enter old password, new password, and new password again (for
confirmation) as prompted.

(5) Enter passwords as prompted and press key.

Figure 8-5-1

8-22 Revision April, 2014

Chapter 8: DGN group NC300

See the operation steps described below for equipment permission resetting:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (M SCP) to enter the equipment permission function bar.

(4) ※ Press key (UNLOCK) and an entry dialog box pops up for users to
enter a password when equipment permission is locked.

(5) Enter a valid password, press key and the equipment permission is
revoked.

Note:
The default password of equipment permission is 0000, which means the permission is
unlocked and all functions can be accessed. When the password is modified, the
equipment permission is enabled and it means the related functions can be accessed
with the permission only.

See the operation steps described below for equipment permission lock up:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (M SCP) to enter the equipment permission function bar.

(4) ※ Press key (LOCK) to lock permission when it is revoked.

Revision April, 2014 8-23

NC300 Chapter 8: DGN group

User reset function allows the equipment supplier to reset the user’s password. Once
the client forgets the password, the equipment supplier is able to reset as the default
password. This function is active only when the password is not the default value. See
below for the operation steps.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to display the password setup function bar.

(3) Press key (M SCP) to display the equipment permission function bar.

(4) Press key (RST U1) / key (RST U2) to reset the user’s password.

8.5.3 User permission

Users can set up permission for users 1 and 2. The permission function covers
password change, permission lock and permission unlock. The password is composed
of up to four alphanumeric characters (symbols excluded).

See the operation steps described below for user password change: (illustrated with
user permission 1)

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) ※ Press key (U1 SCP) and the password entry dialog box for unlocking
user permission 1 displays if the user permission 1 is locked.

(4) Enter valid password for user permission 1, press key to revoke user
permission 1 and display relevant function items.

(5) Press key (PWD CHG) and an entry dialog box pops up for users to enter
old password, new password, and new password again (for confirmation) as
prompted.

(6) Enter passwords as prompted and press key.

8-24 Revision April, 2014

Chapter 8: DGN group NC300

See the operation steps described below for user permission reset:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) ※ Press key (U1 SCP) and the password entry dialog box for
unlocking user permission 1 displays if the user permission 1 is locked.

(4) Enter valid password for user permission 1, press key to revoke user
permission 1 and display relevant function items.

See the operation steps described below for user permission lockup:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) ※ Press key (U1 SCP) to display relevant function items if user
permission 1 is revoked.

(4) Press key (LOCK) to resume locking user permission 1.

Note:
The function of user permission is the same as equipment permission. Its default
password is 0000, which means all functions are available. If the user password is
changed, the user permission is enabled.

Revision April, 2014 8-25

NC300 Chapter 8: DGN group

8.5.4 Timed use

Users can assign a timed use of the controller to limit its use in a set period of time.
The system controls given days or hours for the use of the controller automatically.
Users can revoke or reset the time limit only with valid permission when the time limit is
active. The "deadline" in the time limit screen remains blank when no time limit is set or
the limit is revoked as shown in Figure 8-5-2. If there is an active time limit in existence
and it is not revoked, the "deadline" in the time limit screen indicates a valid due date
as shown in Figure 8-5-3:

Figure 8-5-2

Figure 8-5-3

This screen helps users to know to which date the controller can be used normally.
After the due date, the system will be locked unless the time limit is revoked or
extended to a later date. Otherwise, no G code program can be executed manually or
automatically. Please contact the dealer/service provider in case it is overdue.

8-26 Revision April, 2014

Chapter 8: DGN group NC300

This function enables users to set up a time limit when there is no time limit in
existence. See the operation steps described below for time limit setup:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (EXPIRE) to display the time limit information.

(4) Press key (SETTING) to enter the limit setup page.

(5) After entering the password of legal permission, the system’s time limit control is
activated.

See the operation steps described below for revoking a time limit. Please contact the
dealer/service provider for further information.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (EXPIRE) to display the remaining time information.

(4) Press key (RELEASE) to pop up the limit revoking dialog box as shown
in Figure 8-5-4.

Figure 8-5-4

Revision April, 2014 8-27

NC300 Chapter 8: DGN group

(5) With proper authorization, enter an activation code, press key, restart the
system and the time limit is now revoked.

Note:
After the time limit is revoked, the "deadline" field turns blank, as shown in Figure
8-5-5, and indicates that the system does not have a time limit set up.

Figure 8-5-5

The management of time limit permission must go through the proper authorization to
lock or unlock the time limit permission. When time limit is activated, only when
entering the correct password can the permission be revoked. After the permission is
revoked, all time limit function is available, including password change, permission
lock/revoke and etc. The password is composed of up to 4 alphanumeric characters
(symbol excluded).

See the operation steps described below for changing the password of time limit.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (EXPIRE) to display the remaining time information.

(4) ※ Press key (EXP SCP) and the password entry dialog box for unlocking
time limit permission displays if the time limit permission is locked.

(5) Enter valid password for time limit permission, press key to revoke time
limit permission and display relevant function items.
8-28 Revision April, 2014
Chapter 8: DGN group NC300

(6) Press key (PWD CHG), and an entry dialog box pops up for users to
enter old password, new password, and new password again (for confirmation) as
prompted.

(7) Enter passwords as prompted and press key.

See the operation steps described below for revoking the time limit permission.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (EXPIRE) to display the remaining time information.

(4) ※ Press key (EXP SCP) and the password entry dialog box pops up for
unlocking time limit permission displays if the time limit permission is locked.

(5) Enter valid password for time limit permission, press key to revoke time limit
permission and display relevant function items.

See the operation steps described below for locking the time limit permission.

(1) Press key to enter the [diagnostics function] page.

(2) Press key (PWD) to enter the password setup function bar.

(3) Press key (EXPIRE) to display the remaining time information.

(4) ※ Press key (EXP SCP) for displaying the relevant function items if the
time limit permission is revoked.

(5) Press key (LOCK) and resume the permission lock.

Revision April, 2014 8-29

NC300 Chapter 8: DGN group

8.6 System information

This function provides program version of hardware and firmware of this system as
required for system maintenance and performance optimization. It covers the options
of system status and hardware and firmware serial number.

See the operation steps described below for system status display:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (STATUS) to enter the system information screen.

(3) Press key (SYSTEM) to enter the system status information screen.

The firmware serial number function displays the firmware version number as well.
See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (STATUS) to enter the system information screen.

(3) Press key (FW SN) to display firmware version information as shown in
the figure below.

Figure 8-6-1

8-30 Revision April, 2014

Chapter 8: DGN group NC300

See the operation steps described below for hardware serial number display:

(1) Press key to enter the [diagnostics function] page.

(2) Press key (STATUS) to enter the system information screen.

(3) Press key (HW SN) to display hardware version information.

Revision April, 2014 8-31

NC300 Chapter 8: DGN group

8.7 Gain adjustment

The auto adjusted gain compensation enables the system and the servo drive to work
out even better motion control to meet different mechanical requirements of various
machines. The NC300 controller retrieves initial parameters of the servo, calibrates
motion control with gain adjustment function and feeds back the calculated gains to the
servo drive to unify control parameters of the controller and the servo for easier system
gain adjustment enhancement and the best control accuracy. Sub menu items of this
function are described with the function screen as shown in the figure below.

Anchor point setup

Anchor point 1/
Anchor point 2

Servo parameter ID
Servo parameter ID
and name

Adjustment
conditions

Calculated results Existing settings of the

after adjustments
system
Display calculated
results after auto Indicates servo settings
gain currently used by the
system

Next axis: This function switches axial gain settings. The auto gain can be adjusted by
individual axis. After the first axis is adjusted, users need to switch to the next one for
its adjustment. See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to enter the next function page.

(3) Press key (TUNING) to enter the auto gain setup page.

(4) Press key (NEX AX) to switch to the next axis for its axial gain
parameters setup.

8-32 Revision April, 2014

Chapter 8: DGN group NC300

Read the Servo: After the auto gain adjustment function is activated, its parameter
values have been synchronized with those of the servo. To accommodate the function
of gain adjustment, the calculated results after auto gain operation are not written back
to the servo. This function can be used to recover servo parameters.

See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to switch to the next function page.

(3) Press key (TUNING) to enter the auto gain setup page.

(4) Press key (READ) to return parameter values to the controller from the
servo.

Revision April, 2014 8-33

NC300 Chapter 8: DGN group

Start, Jog←, Jog→, Positioning 1, Positioning 2: This sets up the operation of

auto gain adjustment. It starts the action of auto gain, and sets up anchor point
direction and operation. See the operation steps described below for continuous
operation.

See the operation steps described below for single axis operation:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to switch to the next function page.

(3) Press key (TUNING) to enter the auto gain setup page.

(4) Press key to switch to the next function page.

(5) Press key (JOG ←) to offset gain motion to the anchor point to the left.

(6) Press key (POS 1) to set the point as the left anchor point of the gain
motion.

(7) Press key (JOG →) to offset gain motion to the anchor point to the right.

(8) Press key (POS 2) to set the point as the right anchor point of the gain
motion. The gain trip is now limited between both points.

(9) Press key (RUN) to execute gain adjustment motion.

(10) Press key (STOP) during auto adjustment motion to complete the
gain adjustment motion. The system then calculates the best gain value
automatically.

8-34 Revision April, 2014

Chapter 8: DGN group NC300

Gain calculation: Users can change low-frequency rigid, bandwidth, or inertia ratio
to fit individual machines. These values can be generated by this function
automatically. See the operation steps described below for single axis operation:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to switch to the next function page.

(3) Press key (TUNING) to enter the auto gain setup page.

(4) Use keys to point to the low-frequency rigid, bandwidth, or

inertia ratio fields to enter settings respectively.

(5) Press key (COMPUTE) to generate new gain values.

Gain and resonance write-in: New gain values are generated after the auto gain
adjustment operation has stopped. If they are the expected optimization values, please
use this function to write them in the servo. See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press function key to switch to the next function page.

(3) Press key (TUNING) to enter the auto gain setup page.
(4) Gain values are generated automatically after gain adjustment operation.

(5) Press key (WR GAIN) to write gain values in the servo. Press key
(WR NOTH) to write resonance suppression values in the servo.

Note:
(a) The newly generated gain adjustment results must be written in the servo
before it can take effect.
(b) After gain and resonance write-in function is executed, the servo parameters
are updated and the old ones cannot be recovered. Please do the write-in
with care.

Revision April, 2014 8-35

NC300 Chapter 8: DGN group

Tapping adjustment: This function fine tunes the machine and servo for tapping
application. See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to switch to the next function page.

(3) Press key (TUNING) to enter the auto gain setup page.
(4) Complete X, Y, Z axes and spindle's gain adjustment first.

(5) Press key continuously to enter the last page.

(6) Press key (TAP RIV) to prompt the operation screen.

(7) Press key (TAP SET) again and the confirmation dialog box will pop up.

Press Y (Yes) key and press key to fine tune the machine for tapping
operation.

Servo parameter: This function sets up the parameter for easy servo parameter
display and setup in the gain adjustment screen:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to switch to the next function page.

(3) Press key (TUNING) to enter the auto gain setup page.

(4) Continuously press key to enter the last page.

(5) Press key (SERVO) to enter the servo parameter screen.

(6) Point to the desired field and type in relevant data, press key to set up a
given field.

8-36 Revision April, 2014

Chapter 8: DGN group NC300

8.8 Import
The system features a parameter import/export function for managing system
parameters. Users can import correct parameters to the system to return it to normal or
export existing parameters for backup. It is used for system recovery or optimization.
This function can be used only with proper permissions. It recovers system
abnormalities caused by parameter errors at fast speed.

See the operation steps described below for parameter import:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to switch to the next function page.

(3) Press function (IMPORT) key to search parameter files in the USB drive
(with file name in format of GMCExport.ncp).

(4) Use keys in the parameter file selection interface,

press key to check the parameter items for import.

(5) Press key (IMPORT) to import the selected parameter files.

Revision April, 2014 8-37

NC300 Chapter 8: DGN group

8.9 Export
Export function: System parameters may be regulated to meet the requirements of
different scenarios during actual application. After the system is optimized, this function
can be used to export parameter values for backup and control. This function can be
used only with proper permissions.

See the operation steps described below for parameter export:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to switch to the next function page.

(3) Press key (EXPORT) to enter the parameter export selection screen.

(4) Use keys in the parameter file selection interface,

press key to check the parameter items for export.

(5) Press key (EXPORT) to export the selected parameter files to a USB
drive.

Figure 8-9-1

8-38 Revision April, 2014

Chapter 8: DGN group NC300

8.10 Multi language download

Language support of the group screens and function bars includes both Chinese and
English. For other language support, please enhance the interface language with this
multi-language downloading function. Please contact the dealer/service provider
for details.

8.11 System recovery

This function can be used to recover a system in the status of severe error,
malfunctioning or system data damage with the previous parameter backup file. Enter
the restore options screen. Checked items are data that have been damaged and can
be restored with this function. This function can be used only with proper permissions.

See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Press key to enter the next function bar page.

(3) Press key (RECOVER) and the user permission dialog box will pop up.

(4) Use keys in the parameter file selection interface,

press key to check the desired restore file.

(5) Press key at the item that has been checked to uncheck it.

(6) Press key (OK) to start system recovery.

Revision April, 2014 8-39

NC300 Chapter 8: DGN group

8.12 LOGO download

The startup screen of the system can be customized with user exclusive contents for
logo presentation or other uses with this function. This function can be used only with
proper permissions.

See the operation steps described below:

(1) Press key to enter the [diagnostics function] page.

(2) Continuously press key to enter the function bar for displaying the next
page.
(3) Insert a USB drive containing the correct NC300 system startup screen file.

(4) Press key (LOGO WR), a dialogue box pops up.

(5) Enter “Y”. It automatically access and load in the start-up file from USB.
(6) Restart the system after the LOGO image file is updated.

8-40 Revision April, 2014

Chapter 9: PAR Group NC300

Chapter 9: PAR group

PAR Group regulates and sets up a full range of system control and computing parameters
for easy management and optimized setup. The PAR group covers the setup of parameters
for operation, tool magazine, machining, spindle, mechanical, origin, compensation, and
system.

9.1 Process parameter

The process parameter sets up parameters for the maximum cutting speed, cutting
and smoothing acceleration and deceleration time. These parameters have a heavy
impact on machining quality. For the best operation effect, please set up these
parameters based on actual requirements.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key (Process) to enter the process parameter setup screen.

(3) Use keys to point to the desired data field, and type in proper
values (Refer to the recommended values displayed at lower right corner of the
screen) as shown in Figure 9-1-1.

(4) Press key to complete setting up the field.

Figure 9-1-1

Revision April, 2014 9-1

NC300 Chapter 9: PAR Group

9.2 Operation parameter

Users can combine the execution and computing of a macro program in the G code file
for composite motions. Users also can control or execute the execution of a macro
program in the operation parameter screen.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key (Operate) to enter the operation parameter setup screen.

(3) Use keys to point to the desired data field, and type
in proper values (Refer to the recommended values displayed at lower right
corner of the screen) as shown in Figure 9-2-1.

(4) Press key to complete setting up the field.

Figure 9-2-1

9-2 Revision April, 2014

Chapter 9: PAR Group NC300

9.3 Tool magazine parameter

The tool magazine parameters set up relevant functions of the tool magazine including
its mechanical type, quantity, and startup. For settings of tool magazine hardware
relevant parameters, please contact the dealer/service provider.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key (Maga) to enter the tool magazine parameter setup screen.

(3) Use keys to point to the desired data field, and type in proper
values (Refer to the recommended values displayed at lower right corner of the
screen) as shown in Figure 9-3-1.

(4) Press key to complete setting up the field.

Figure 9-3-1

Revision April, 2014 9-3

NC300 Chapter 9: PAR Group

9.4 Spindle parameter

The spindle parameters set up various spindle function including gains, maximum
speed, and positioning errors.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key (Spindle) to enter the spindle parameter setup screen.

(3) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen)
as shown in Figure 9-4-1.

(4) Press key to complete setting up the field.

Figure 9-4-1

9-4 Revision April, 2014

Chapter 9: PAR Group NC300

9.5 Mechanical parameter

Users can set up the mechanical equipment relevant parameters of software/hardware
limit, screw guide pitch and number of pulses of encoder.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key (Machine) to enter the mechanical parameter setup screen.

(3) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen)
as shown in Figure 9-5-1.

(4) Press key to complete setting up the field.

Figure 9-5-1

Revision April, 2014 9-5

NC300 Chapter 9: PAR Group

9.6 Origin parameter

The origin parameter sets up coordinates from mechanical origin to the fourth
reference point and origin searching mode.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key (Home) to enter the origin parameter setup screen.

(3) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen)
as shown in Figure 9-6-1.

(4) Press key to complete setting up the field.

Figure 9-6-1

9-6 Revision April, 2014

Chapter 9: PAR Group NC300

9.7 Network Setup

This function enables users to remote connect to a PC through Ethernet
communication. Working together with CNC Network software and the network setting
of the NC300 numerical control system, users can use one PC to control multiple
NC300 controllers for online file management, file sharing, file management and
transmission-along-with-machining (DNC) through remote network communication.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key to enter the page containing this function bar.

(3) Press key (Network Set) to enter the network setup page.

(4) Use keys to point to the desired data field, type in proper
values (Refer to the recommended values displayed at lower right corner of
the screen) as shown in Figure 9-7-1.

(5) Press key to complete setting up the field.

Figure 9-7-1

Revision April, 2014 9-7

NC300 Chapter 9: PAR Group

Parameter
Parameter Name Parameter Range or format
code
Length:1~8
10030 Host name
Actual setting: 1~8 characters
Data format: ×××.×××.×××.×××
10031 IP address
Actual setting: 192.168.0.2
Data format: ×××.×××.×××.×××
10032 Subnet mask
Actual setting: 255.255.255.0
Data format: ×××.×××.×××.×××
10033 Default gateway
Actual setting: 0.0.0.0
Data range: 0~1
10034 Networking enabled
Actual setting: 1
Data range: 0~1
10035 DHCP enabled
Actual setting: 0
10036
Remote computer IP Data format: ×××.×××.×××.×××
~
address 1~5 Actual setting: 192.168.0.1
10040

9-8 Revision April, 2014

Chapter 9: PAR Group NC300

9.8 Compensation parameter

The compensation parameter sets up relevant compensation data to compensate
errors caused by mechanical factors during actual machine operation. That is to say,
the compensation is given by the control system with considering the machine
features.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key to enter the page containing this function bar.

(3) Press key (Comp) to enter the compensation parameter setup screen.

(4) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen)
as shown in Figure 9-8-1.

Figure 9-8-1

(5) Press key to complete setting up the field.

(6) The field of input length compensation can be completed by pressing key

(um) to type in absolute length compensation in unit of um; or press key

(um+) to type in incremental length compensation in unit of um.
(7) Compensation data generated by calibration instruments can be converted by

the CNC SOFT program. Press key (import) to import compensation data

Revision April, 2014 9-9

NC300 Chapter 9: PAR Group

which is the absolute type data import; or press key (import +) to import
compensation data as the incremental type of data import.

(8) After entering all compensation value, press key (OK) to confirm and
update the compensation parameters.

9-10 Revision April, 2014

Chapter 9: PAR Group NC300

9.9 System parameter

The system parameters enable users to customize operation environment including
system date, system time, background color of screen, function bar color, and tab
color.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key to enter the page containing this function bar.

(3) Press key (System) to enter the system parameter setup screen.

(4) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen)
as shown in Figure 9-9-1.

Figure 9-9-1

(5) Press key to complete setting up the field.

(6) As for the setting of color items, press key (Color) and the color selection
dialog box will pop up.

Revision April, 2014 9-11

NC300 Chapter 9: PAR Group

(7) To reset the system environment back to its factory defaults status, press
key (Default) and a confirmation dialog box displays.

(8) Press "Y" (Yes) and key to reset the system back to its factory defaults
status.

9-12 Revision April, 2014

Chapter 9: PAR Group NC300

9.10 MLC setting

This function sets up the display environment of the component device and color of the
MLC ladder diagram.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key to enter the page containing this function bar.

(3) Press key (MLC) to enter the MLC setup screen.

(4) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen)
as shown in Figure 9-10-1.

Figure 9-10-1

(5) Press key to complete setting up the field.

(6) As for the setting of color item, press key (Color) and the color
selection dialog box will pop up.
(7) To reset the system environment back to its factory defaults status, press

key (Default) and a confirmation dialog box displays.

(8) Press "Y" (Yes) and key to reset the system back to its factory defaults
status.
Revision April, 2014 9-13
NC300 Chapter 9: PAR Group

9.11 Graph parameter

The graph parameter defines the display range of motion trails and provides GRA
group required plotting settings.

Figure 9-11-1
See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key to enter the page containing this function bar.

(3) Press key (Graphic) to enter the graph parameter setup screen.

(4) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen)
as shown in Figure 9-11-1.

(5) Press key to complete setting up the field.

(6) As for the setting of color item, press key (Color) and the color selection
dialog box will pop up.

(7) To reset the system environment back to its factory defaults status, press
key (Default) and a confirmation dialog box displays.

(8) Press "Y" (Yes) and key to reset the system back to its factory defaults
status.

9-14 Revision April, 2014

Chapter 9: PAR Group NC300

9.12 Servo parameter

Through the servo parameter setup screen, the servo end can control and set up
parameters.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key to enter the page containing this function bar.

(3) Press key (Servo) to enter the servo parameter setup screen.

(4) Use keys to point to the desired data field, type in proper values
(Refer to the recommended values displayed at lower right corner of the screen).

(5) Press key to complete setting up the field.

Figure 9-12-1

Revision April, 2014 9-15

NC300 Chapter 9: PAR Group

9.13 Channel setup

This function sets up the number and definition of the axis employed by a system as
shown in Figure 9-13-1. The system mode cannot be set up in Auto and Manual
modes.

Figure 9-13-1

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key repeatedly to enter the page containing this function bar.

(3) Press key (Config) to enter the channel setup screen.

(4) Use keys to point to the desired axis function fields, press
key to check the axis and activate its attributes. Users can select either the NC or
MLC axis attribute as desired.

(5) To define axis attributes: Use keys to point to the

desired field and press key to check the field.

(6) After the axis attribute is defined, use keys to point

to the port field of the axis, press key and the port number entry box will

pop up, press ~ keys to enter a unique port number, press

key and the port number of the axis is set.

9-16 Revision April, 2014

Chapter 9: PAR Group NC300

(7) Press key (OK) after all axes are defined.

(8) Restart the NC300 numerical control system to effect the changes that just
made.

Note:
(a) Please check to activate the axis name before enabling the axis. Users can
set up the definition to control the axis only after it is activated. Either the NC
or MLC axis can be selected, but not both, and assign a port number (unique
from other axis port numbers).
(b) To revoke (cancel) axis function: point to the desired field, press the ENTER
key to uncheck it, and the function of this axis is disabled.
(c) Parameter fields marked with the letter 'P' indicates that changes can take
effect only after the NC300 numerical control is restarted. Otherwise, changes
take effect immediately.

Revision April, 2014 9-17

NC300 Chapter 9: PAR Group

9.14 RIO setting

The NC300 numerical control system can add external control devices through its I/O
expansion module. The I/O function module can be enabled in RIO setup page as
shown in Figure 9-14-1. See the operation steps described below:

Figure 9-14-1

(1) Press key to enter the [Parameter Setup function] screen.

(2) Press key to enter the page containing this function bar.

(3) Press key (Set RIO) to enter the I/O expansion module setup page.

(4) Use keys to point to the desired RIO port fields, press key
to check the field and display the I/O setup screen of the selected port.

(5) Use keys to point to the polarity setup field, press key and

the entry box will pop up, press key after data entry and the polarity is
set.

(6) Then, use keys to move to the disconnection output field, press

key to check/uncheck setup values.

(7) Press key (OK) after all I/O modules function are set.

9-18 Revision April, 2014

Chapter 9: PAR Group NC300

9.15 Search
This function enables users to search and point to desired parameter fields with a
parameter code for faster and easier access to the screen containing a given
parameter.

See the operation steps described below:

(1) Press key to enter the [Parameter Setup function] screen.

(2) Continuous press key to enter the page containing this function bar.
(3) Type in the parameter code to be searched in the field located at the lower
bottom of the screen.

(4) Press key (Search) to start searching.

Note:
Apart from using the function key to search the parameter, users can enter the
parameter number in the screen of PAR group. The method is: S + parameter
number and then press ENTER.

Revision April, 2014 9-19

NC300 Chapter 9: PAR Group

(This page is intentionally left blank.)

9-20 Revision April, 2014

Chapter 10: SOFT group NC300

Chapter 10: SOFT group

SOFT group is a special control feature provided by NC300 numerical controller to replace
the physical secondary control panel or special operation functions. With the CNC SOFT
software, users can add a secondary control panel screen and use it to do exactly the
operations available in the physical secondary control panel.
This function can be used in environments without physical secondary control panel to
support special repair servicing needs. Users may use it to add software keys with
self-developed special controls for expanded functionality. This group function can replace
the physical secondary control panel's control or function options.

10.1 Control panel (※Example: without physical operation

panel)
See Figure 10-1-1 for an example of the function devices offered by this function. Keys
and buttons of a physical secondary control panel are simulated with control
components. Each device is turned on or off with relevant function key. Device types
and priorities vary with user preference. Icons are sorted from bottom to top.

See the operation steps described below for the operation of the control panel:

(1) Press key to enter the SOFT group screen.

(2) Press key (control panel) to enter the device function bar screen.

(3) Use keys to access the corresponding device function page as

shown in Figure 10-1-1.

Figure 10-1-1

Revision April, 2014 10-1

NC300 Chapter 10: SOFT group

(4) Use ~ keys to enable or disable device function.

10-2 Revision April, 2014

Chapter 10: SOFT group NC300

Control panel (※Example: with physical operation panel)

The software panel can define additional functions and locations which are required by
expanded requirements. In a machine with physical secondary control panel, use the
CNC SOFT software to add auxiliary configuration functions, including spindle tool
release, auto chip removal, and auto power off in the screen as shown in Figure
10-1-2.

Figure 10-1-2

See the operation steps described below for the operation of the control panel:

(1) Press key to enter the SOFT group screen.

(2) Press key (control panel) to enter the device function bar screen.

(3) Use keys to access the corresponding device function page.

(4) Use ~ keys to enable or disable device function.

Revision April, 2014 10-3

NC300 Chapter 10: SOFT group

10.2 Factor regulation (※Example: without physical operation

panel)
Available factors are: cut feeding rate, fast feed rate, spindle speed, jog, and hand
wheel.
Use the up and down arrow keys to select factor type and operation as shown in Figure
10-2-1.
Range of cut feeding rate: 0% ~ 150% (in steps of 10%).
Range of fast feeding rate: F0, 25, 50, 100(%).
Range of spindle speed: 50% ~ 120% (in steps of 10%).
Range of jog factor: 0, 2, 3, 5, 8, 13, 20, 32, 50, 80, 120, 200, 320, 500, 790, 1260
mm/min.
Range of hand wheel factor: 0.001, 0.01, 0.1 (mm)

Figure 10-2-1

See the operation steps described below for factor regulation:

(1) Press key to enter the SOFT group screen.

(2) Press key (factor regulation) to enter the factor regulation setup screen.

(3) Use keys to point the setup box to the desired regulation icon as
shown in Figure 10-2-1.
(4) Available options in the setup box are: increasing, decreasing, 100%, and 0%.
Press the relevant function key to adjust factors as desired.

10-4 Revision April, 2014

Chapter 10: SOFT group NC300

10.3 Axis operation (※Example: without physical operation

panel)
Use the SOFT group function to set the machine's individual axis for axial movements
through software panel as shown in Figure 10-3-1.

Figure 10-3-1

See the operation steps described below for axis operation:

(1) Press key to enter the SOFT group function screen.

(2) Press key (axis operation) to enter the axis operation screen.

(3) Use ~ keys to do axial movements.

Note:
(1) Configuration illustrations described here prioritize functions that are more
likely to be used during machining. For instance, program execution,
execution stops, and single step execution are placed in the first row.
(They can be arranged as desired by the software.)
(2) The travel distance (or speed) of axis operation varies with factor settings
as described in Section 10.2.

Revision April, 2014 10-5

NC300 Chapter 10: SOFT group

(This page is intentionally left blank.)

10-6 Revision April, 2014

Appendix A: Group function map NC300

Appendix A: Group function map

POS function map

[ABS.]

[REL.] [CLR ALL.]

[CLR X.]

[CLR Y.]

[CLR Z.]

[CLR A.]

[CLR B.]

[CLR C.]

[MECH]

Revision April, 2014 1

NC300 Appendix A: Group function map

PRG function map 1 – edit mode PRG function map 2 – edit mode

PRG function map – auto mode PRG function map – manual mode

2 Revision April, 2014

Appendix A: Group function map NC300

PRG function map [JOG mode], [Hand wheel mode]

PRG function map [Homing mode]

Revision April, 2014 3

NC300 Appendix A: Group function map

OFS function map - 1

4 Revision April, 2014

Appendix A: Group function map NC300

OFS function map - 2

Revision April, 2014 5

NC300 Appendix A: Group function map

GRA function map 1

[Cutting
[X-Y/Y-Z/X-Z/X-Y-Z]
path]

[Center]

[Zoom in]

[Zoom out]

[Draw]

[Stop
drawing]

[Up]

[Down]

[Left]

[Right]

[Cutting
[X-Y/Y-Z/X-Z/X-Y-Z]
preview]

[Center]

[Zoom in]

[Zoom out]

[Preview]

[Stop
preview]
To next page...

6 Revision April, 2014

Appendix A: Group function map NC300

GRA function map 2

ALM function map

Revision April, 2014 7

NC300 Appendix A: Group function map

DGN function map 1

8 Revision April, 2014

Appendix A: Group function map NC300

DGN function map 2

Revision April, 2014 9

NC300 Appendix A: Group function map

DGN function map - 3

10 Revision April, 2014

Appendix A: Group function map NC300

DGN function map - 4

Revision April, 2014 11

NC300 Appendix A: Group function map

DGN function map - 5

12 Revision April, 2014

Appendix A: Group function map NC300

DGN function map - 6

Revision April, 2014 13

NC300 Appendix A: Group function map

DGN function map - 7

...from last page

[TEXT WR]

[IMPORT] [IMPORT]

[EXPORT] [EXPORT]

[RECOVER] [OK]

[LOGO
WR]

14 Revision April, 2014

Appendix A: Group function map NC300

PAR function map - 1

Revision April, 2014 15

NC300 Appendix A: Group function map

PAR function map - 2

16 Revision April, 2014