SPECIFICATION FOR PLC
A) CONTROLLER MODULE
Type 32 BIT
Processor speed 100 MHz
CPU Memory 1 MB
Flash Memory Built in 256 KB
Boolean Execution Speed 0.4 micro sec / Boolean function
Floating Point Maths Yes
Embedded Communication Serial
Built In Serial Port Bidder to decide
Discrete I / O processing 6000
Analog I / O processing 8 KB
Protocols Supported As per Bidder’s standard
B) DISCRETE INPUT MODULE
Input Module 24 V DC Positive / Negative Logic ,
Intelligent Type
Module Function Input
Input Rated voltage 24 V DC Positive / Negative
Inputs per Module 32
Input Group Four (4) isolated Groups of eight (8)
input each.
Channel Indication LED for each channel
Fault Indication Module Fault Indication on the module
Discrete Input Voltage Range 0 – 30V DC
ON State Voltage 13.5 – 30 V DC
OFF State Voltage 0–5V
Isolation between circuit and back 1500 V rms
plane
Isolation between input circuits 500V rms
Surge withstand capability 1000V DC/500V AC from point to
point/1000V AC/DC from point to system
ground
Surge Immunity 1kV peak
Impedance 20 K Ohms ( Typical )
Proximity Switch Compatible Yes
C) DISCRETE OUTPUT MODULE
Module Type Discrete , Intelligent type
Module Function Output
Outputs per Module 32
Output Group Four (4) Isolated groups of eight (8)
output each
Channel Indication LED for each channel
Fault Indication Module Fault Indication on the module
Discrete output voltage range 20 – 60 V DC
Response time ON 1 ms Max.
Response time OFF 1 ms Max.
Isolation between any output and 1500 V rms
back plane
Isolation between output circuits 500V rms
Surge withstand capability 1000V DC/500V AC from point to
point/1000V AC/DC from point to system
ground
Surge Immunity 1kV peak
D) OUTPUT RELAY MODULE
Module Type Discrete
Module Function Output
Discrete Output Type Potential free Relay O/P
Discrete Output Relay Voltage 24V DC
Outputs per Module 32 Non-Latching Type
Channel Indication LED for each channel
Response time ON 10 ms with 1 ms typical bounce time
Maximum Power It can handle
Maximum Switching Voltage As 220V DC, 250V AC resistive load.
Maximum Switching Current 0.5 Amps 24 VDC, 2 Amps 240 VAC
resistive load (2A, 220VDC whenever
required)
Contact Type Silver alloy ( gold clad )
Contact Resistance 50 mw ( by voltage drop 6V DC 1A )
typical
E) ANALOG INPUT MODULE
Module Type Analog
Analog Input Type Current
Inputs per module 16
Analog Input Current 4-20 mA
Fault Indication Module Fault Indication on the Module
Response Time 5 ms Typical
Resolution 0 to 1 micro amp per LSB step on 4-
20Ma
Accuracy + 0.05 % of full scale
Isolation between any output and 1500 V rms
back plane
Isolation between output circuits 500V rms
Isolation between channel to 1000V DC/AC
channel
Isolation between channel to logic 1000V DC/AC
Surge Immunity 1kV peak
F) ANALOG OUTPUT MODULE
Module Type Analog
Module Function Output
Output Type Current
Analog Outputs per Module 16
Analog Output 4-20 mA, 600 Ω load
Fault Indication Module Fault Indication on the Module
Isolation between any output and 1500 V rms
back plane
Isolation between output circuits 500V rms
Isolation between channel to 1000V DC/AC
channel
Isolation between channel to logic 1000V DC/AC
Surge Immunity 1kV peak
G) I / O INTERFACE MODULE
Module Type Bus Interface
Electrical Isolation Non-isolated differential communication
Power supply 24V DC
H) ETHERNET COMMUNICATION MODULE
Module Type Redundant ( Hot Stand by)
Ethernet Data communication rate 10/ 100 Mbps
Electrical Isolation Non-isolated differential communication
Built in port Ethernet TCP/IP
I) SYSTEM RACK POWER SUPPLY
Module Function Power Supply
Power Source 240 V AC, 50Hz UPS
Output Power As per System requirement
J) OPERATOR’S STATION / ENGINEERING STATION (PC BASED)
Processor Intel core 2 duo or higher
Enclosure Tower
Internal clock 3.2 GHz
Architecture 32 bit
Video output SVGA
RAM 2GB (Minimum) expandable to 4GB or
Higher as per manufacturers standard.
Hard drive 250 GB SATA
Cache 8 MB Level 3
DVD Drive DVD Read –Write
Power supply 240V AC, 50Hz
Operating system Window XP Pro, window 7 or latest
Accessories Industrial type keyboard with optical
mouse
K) MONITOR
Type TFT
Sync. Multisync.
Screen diagonal 21” flat
Display Super Video Graphic Array
Array 1280 x 1060 non-interlaced, refresh rate
min. 85Hz
Degree of protection IP-30
Screen Direct-etched , high contrast, optical
quality, antistatic.
External Controls Brightness, contrast, Horizontal / Vertical
amplification & shift
Power supply 240 V, 50 Hz, 1 phase
Ambient temperature 0-50ºC
Humidity 95% non-condensing.
L) LASER PRINTER
Type Heavy-duty laser, table top
Printer Memory 128 MB or higher suitable for network
printing.
Speed Monochrome 24 ppm - A4
Color 6 ppm - A4
Resolution 600 DPI in color
No. of color (Basic) 4 (four) minimum
Duty cycle 50000 pages / month printing capability
with 3000 sheet input capability.
Power supply 230 V, 50 Hz, 1 phase
Ambient temperature 0-50ºC
Humidity 95% non-condensing.
Size of paper Letter, A4, Legal, Ledger, A3
Print media Plain paper, transparencies, envelopes
Accessories a) a) Adapters
b) b) Connector Cable
c) c) Multiplexer switch (4 point)
M) DOT MATRIX PRINTER
Type Dot Matrix , Table top, Black / White
Printer
Speed (300 cps) 132 columns
N) ETHERNET SWITCH
a. Ethernet switch with port of 10 / 100 Mbps.
b. No. of port will be as per requirement with spare.
c. Preferable Make: CISCO / Enterasys
