CHRYSO® TAPELASTIC
Two Part Acrylic Polymer Based Elastomeric
Waterproof Coating
Description Method of Application
Surface Preparation
CHRYSO TAPELASTIC is a two component, elastomeric, acrylic
polymer modified cementitious waterproofing protective Prior to application of CHRYSO TAPELASTIC, all surfaces must be
coating system in slurry form. prepared properly to avoid failure. The surface shall be cleaned
to remove all dust, foreign materials/loose particles or any
Indicative Characteristics deposits of contaminants, which could affect the bond between
the original substrate and the CHRYSO TAPELASTIC system. This
Color of Pack-A (Liquid) Milky White can be done by scarifying, grinding, water blasting, sand
Color of Pack-B (Powder) Grey blasting, acid washing or any other approved method. Rectify
Color of hardened coating Cement like Grey depression / honey-comb (if any) in the surface, use CHRYSO
Workable time, minutes, 30 (approx.) ARMOURCRETE mortar before application of CHRYSO
27⁰C, 70% RH TAPELASTIC.
% Elongation at 14 days, 30 ( minimum)
ASTM D 638 Mixing
Tensile strength at 14 days, 5 ( minimum with fibre
N/mm2 ASTM D 638 mesh) CHRYSO TAPELASTIC LIQUID PART (polymer) is mixed with
Coverage 1.8-2kg/mm/m2 POWDER PART in the ratio of 1:2.5 by weight with a help of low
Mix Ratio (Liquid: Powder) 1:2.5 speed (300-400 rpm) paddle mixer. The mix has to be stirred
by wt. thoroughly, until a lump-free smooth slurry is obtained. Stand
Initial cure at 270C, for After 24hours for 4-5 minutes after mixing to release air from the mix..
pedestrian traffic
Application
Full cure, days 7
All concrete surfaces (flat and vertical /inclined) shall be
Domains of Application
thoroughly pre-wetted to saturated surface dry condition; at
the same time there should not be any standing water on the
CHRYSO TAPELASTIC is used as a waterproofing
surface or it should not be too wet prior to application of
treatment for roof, basements rafts against rising CHRYSO TAPELASTIC system. Remix the content again with a
dampness, retaining structures, water bodies, spatula and start application by brush, roller or any other
reservoirs, balconies, bathrooms, sunken areas, suitable tools on prepared surface. Minimum two coats are
fountains, dome structures, decks and terraces. recommended. More number of coats can be provided
depending on job requirements. First coat should be allowed to
Damp patches on walls, to seal joints through which air dry for 5-6 hours. Where more tensile strength is required
CHRYSO TAPELASTIC coating should be reinforced with non-
there is possibility of water ingress and in any other
woven fibre glass cloth.
area, where a quick solution for waterproofing and
damp proofing is required.
CHRYSO TAPELASTIC can be reinforced with fibre glass
mats.
The information contained in this technical data sheet is given to the best of our knowledge and the results from extensive testing in order to remain as objective as possible.
However, it cannot, in any case be considered as a warranty involving our liability in case of misuse or any different use of our products from the “Application” paragraph of this
technical data sheet. Some application tests should be carried out before using the product to ensure that the methods of use and conditions of application of the product are
07/01/2017
satisfactory. Our technical assistance is at the disposal of the users.
Consult the latest update of the technical data sheet on our website www.chryso.com
CHRYSO India Private Limited | Registered & Corporate Office : Plot No. D -30/7, TTC Industrial Area, M.I.D.C. Turbhe, Navi
Mumbai – 400705. Maharashtra, INDIA. Tel : +91 22 27685991/2
CHRYSO® TAPELASTIC
Two Part Acrylic Polymer Based Elastomeric
Waterproof Coating
Curing Shelf Life & Storage
After application of CHRYSO TAPELASTIC system, initial air- 12 months from the date of manufacturing when stored in un-
drying shall be done for 3-6 hours. During this period, no water opened, original sealed and dry condition at a temperature
should be used for curing. If there is a chance of rain or hot range from +5⁰C to 40⁰C
(temperature above 40⁰C), windy atmospheric conditions
within this period, protect the coating by covering with Packing
waterproof plastic sheet. After a maximum period of 6-8 hours
after the final application, moist curing shall be done for the 15 kg kit
next 2-3days, either by spraying water or by using wet burlap.
During this period, the CHYRSO TAPELASTIC coating at no point Precautions
of time should be left completely dry or submerged in water.
After the moist curing the CHRYSO TAPELASTIC coating shall be Reinforcement rods and other sharp materials should
allowed to air dry for 3 days before submersion in water. not be dragged over the CHRYSO TAPELASTIC
membrane, as this can puncture the same.
CHRYSO TAPELASTIC shall always be used in
Advantages combination of Pack A and Pack B in recommended
ratio for the indented purpose as mentioned above.
Resistant to UV (Ultra - Violet) rays
Develops excellent bond with most of the building
materials. Safety
Prevents peeling and blistering
Wear hand gloves, safety shoes and safety goggles
Arrests salt petre and prevent penetration of salts into while using and handling the product.
concrete and mortar.
In case eyes or mouth are affected wash with plenty
Unaffected by chemical attacks ranging from mild acids of clean water and seek medical treatment
immediately.
and strong alkalis.
Highly durable in continuous wet service condition. Before use, refer to the Material Safety Data Sheet.
The MSDS is available on www.chryso.com
One time application, properties improve with age.
Versatile product – can be used for
waterproofing, bonding agent for old concrete to
new concrete and repair mortar.
The information contained in this technical data sheet is given to the best of our knowledge and the results from extensive testing in order to remain as objective as possible.
However, it cannot, in any case be considered as a warranty involving our liability in case of misuse or any different use of our products from the “Application” paragraph of this
technical data sheet. Some application tests should be carried out before using the product to ensure that the methods of use and conditions of application of the product are
satisfactory. Our technical assistance is at the disposal of the users.
Consult the latest update of the technical data sheet on our website www.chryso.com
07/01/2017
CHRYSO India Private Limited | Registered & Corporate Office : Plot No. D -30/7, TTC Industrial Area, M.I.D.C. Turbhe, Navi
Mumbai – 400705. Maharashtra, INDIA. Tel : +91 22 27685991/2
