Pioneer Dex-Mg3147zh c3974
Pioneer Dex-Mg3147zh c3974
ORDER NO.
CRT3974
DEX-MG3147ZH/XN/UC
DEX-MG3147ZH /XN/UC
PRODUCED
VEHICLE DESTINATION OEM PARTS No. ID No. PIONEER MODEL No.
AFTER
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3168 CRT3467 G3 Circuit Over View, Mech. Over View, Disassembly, How To Assemble
SAFETY INFORMATION
CAUTION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
B Health & Safety Code Section 25249.6 - Proposition 65
DEX-MG3147ZH/XN/UC
2
1 2 3 4
5 6 7 8
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
Please be sure that all screws are fastened, and that there are no loose screws.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
DEX-MG3147ZH/XN/UC
7
3
5 6 8
1 2 3 4
CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS......................................................................................................................... 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 5
2. SPECIFICATIONS ............................................................................................................................................ 6
2.1 SPECIFICATIONS...................................................................................................................................... 6
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 6
2.3 PANEL FACILITIES .................................................................................................................................... 7
3. BASIC ITEMS FOR SERVICE.......................................................................................................................... 8
3.1 CHECK POINTS AFTER SERVICING....................................................................................................... 8
3.2 JIG CONNECTION DIAGRAM................................................................................................................... 8
3.3 JIGS LIST .................................................................................................................................................. 9
3.4 PCB LOCATIONS .................................................................................................................................... 10
3.5 SYSTEM BLOCK DIAGRAM ................................................................................................................... 11
B 4. BLOCK DIAGRAM.......................................................................................................................................... 12
4.1 BLOCK DIAGRAM ................................................................................................................................... 12
5. DIAGNOSIS.................................................................................................................................................... 20
5.1 OPERATIONAL FLOW CHART ............................................................................................................... 20
5.2 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 21
5.3 ERROR MODE ........................................................................................................................................ 22
6. SERVICE MODE ............................................................................................................................................ 26
6.1 DIAGNOSIS MODE ................................................................................................................................. 26
6.2 CD TEST MODE ...................................................................................................................................... 28
7. DISASSEMBLY............................................................................................................................................... 31
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 34
8.1 PCL OUTPUT CONFIRMATION .............................................................................................................. 34
C
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 35
9.1 EXTERIOR(1) .......................................................................................................................................... 36
9.2 EXTERIOR(2) .......................................................................................................................................... 38
9.3 CD MECHANISM MODULE..................................................................................................................... 40
10. SCHEMATIC DIAGRAM ............................................................................................................................... 42
10.1 TUNER AMP ASSY(SYSTEM)(GUIDE PAGE) ...................................................................................... 42
10.2 TUNER AMP ASSY(POWER SUPPLY)................................................................................................. 48
10.3 KEYBOARD UNIT.................................................................................................................................. 50
10.4 CD MECHANISM MODULE(GUIDE PAGE) .......................................................................................... 52
10.5 ANC UNIT(GUIDE PAGE)...................................................................................................................... 58
10.6 WAVEFORMS ........................................................................................................................................ 64
D
11. PCB CONNECTION DIAGRAM ................................................................................................................... 68
11.1 TUNER AMP ASSY ............................................................................................................................... 68
11.2 KEYBOARD UNIT.................................................................................................................................. 72
11.3 CONTROL UNIT .................................................................................................................................... 74
11.4 ANC UNIT .............................................................................................................................................. 76
11.5 RPS PCB ASSY..................................................................................................................................... 78
12. ELECTRICAL PARTS LIST .......................................................................................................................... 79
DEX-MG3147ZH/XN/UC
4
1 2 3 4
5 6 7 8
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A
- Service Precautions
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic
induction.
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron. D
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
DEX-MG3147ZH/XN/UC
7
5
5 6 8
1 2 3 4
2. SPECIFICATIONS
2.1 SPECIFICATIONS
A
General
Power source ................................................................................................ 13.2 V DC(10.8 V to 16.0 V allowable)
Grounding system .............................................................................................................................. Negative type
Backup current ............................................................................................................................ AVG. 5 mA or less
Weight ............................................................................................................................................................ 2.8 kg
CD player
System ......................................................................................................................... Compact disc audio system
Usable discs ....................................................................................................................................... Compact disc
Distortion ............................................................................................................................................. 0.1 % or less
S/N .................................................................................................................................................... 70 dB or more
B Separation ......................................................................................................................................... 65 dB or more
Stereo balance ....................................................................................................................................... 2 dB within
FM tuner
Frequency ........................................................................................................................ 87.75 MHz to 107.9 MHz
S/N .................................................................................................................................................... 50 dB or more
Distortion ............................................................................................................................................. 1.0 % or less
Image interference ............................................................................................................................ 41 dB or more
IF interference ................................................................................................................................... 91 dB or more
AM tuner
Frequency .............................................................................................................................. 530 kHz to 1 710 kHz
C
S/N .................................................................................................................................................... 45 dB or more
Distortion ............................................................................................................................................. 1.0 % or less
Image interference ............................................................................................................................ 61 dB or more
IF interference ................................................................................................................................... 61 dB or more
DEX-MG3147ZH/XN/UC
6
1 2 3 4
5 6 7 8
A
PRESET CHANNEL RECALL
PRESET CHANNEL MEMORY
FM
AM
SEEK SCAN
SEEK TUNING
POWER/VOLUME
- CD C
DISC SELECT
CD LOAD CD EJECT
CD
TRACK UP/DOWN /
FAST+/FAST-
POWER/VOLUME
E
DEX-MG3147ZH/XN/UC
7
7
5 6 8
1 2 3 4
See the table below for the items to be checked regarding video and audio:
D DISPLAY
H/U
GGD1532
PREMIUM
AMP GA-NET
(XM-TUNER)
E SP-OUT GGD1097
POWER
GGD1531 GGD1535
FM ANTENNA
GGD1351
DEX-MG3147ZH/XN/UC
8
1 2 3 4
5 6 7 8
- Jigs List
A
Name Jig No. Remarks
Assembly jig GGF1538 Assembly jig for G3, 3pcs
Flexible extension GGD1351 Flexible extension
Flexible extension GGD1531 Flexible extension
Flexible extension GGD1532 Flexible extension
Flexible extension GGD1535 Flexible extension
Flexible extension GGD1097 Flexible extension
Extension cable GGD1423 Mechanism test mode
- Grease List
Name Jig No. Remarks
B
PG641 GEM1024 Mechanism Unit(Service)
- CLEANING
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
Portions to be cleaned Cleaning tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
DEX-MG3147ZH/XN/UC
7
9
5 6 8
1 2 3 4
B Keyboard Unit
B
A Tuner Amp Assy
C Control Unit
DEX-MG3147ZH/XN/UC
10
1 2 3 4
5 6 7 8
10A
7.5A
A/C ECU
B
Cross
over
network
STRG SW
C
Electronic
Cross compasses
over
network
20A
ANC MIC
ANC MIC
Radio antenna
FI ECU AMP
DEX-MG3147ZH/XN/UC
7
11
5 6 8
1 2 3 4
4. BLOCK DIAGRAM
4.1 BLOCK DIAGRAM
A
A TUNER AMP ASSY(1/2)
VDD5V
RDSLOCK1
RDSDATA1
RDSHSLK1
RDSCK1
PLLPCE
PLLCE2
LDET
PDO
PCK
WC
PDI
SL
AU
7 6 13 5 10 9 8 11 14 18 19 20 21
A8V
3 I
FM/AM TUNER UNIT OPA
WC
CE2
ROM_VDD
SL
DI
CK
CE1
LDET
DO
RDS_CK
RDS_DATA
RDS_LOCK
RDS_HSLK
TU
A8V
1 I
BA0
VD
VDD5V
2 I
B NJM
V
ANT401
BU
3 AM ANT IC4
1 IC3
5V 3.3V EEPROM
1
ANTB VCO LPF
FM ANT
3
3
ATT RF LPF
IFT CF X-tal
REG OSC
OSCGND
VDD_3.3
RFGND
C
DGND
VCC
22 12 15 4 17
TU33V
CN102 A8V
AUX LCH AUXL
18
AUX DET u COM
Q105 IC601(2/3) ADC
AUX DET AUXDET AUXDET1 PEG294B IC502
16 AK5381VT
B-CAN 78 MCLK MCLK 11 2 ADCL
IC101 P12_5 MCLK AINL
L104 76 BCLK BCLK 12
TJA1040T P12_7
77 LRCLK LRCLK 10
SCLK
BCANH 7 1 CAN_OUT P12_6 LRCK
13 CANH TXD 94 SDT0 SDT0 9
BCANL 6 4 CAN_IN P4_0 SDT0
3 CANL RXD 81 PDN PDN 13
STB P17_2 PDN
39 DACCS
DUETTX 8 CAN_STB P17_6
86 DF
DUET TX DUETTX Q121 DUETTX1 P4_6 DAC DACFL
5 Q122 P4_5
87 DR IC503 DACRL
88 DSW PCM1753DBQ
P4_4
D DUETRX MCLK 16
SCK VOUTL
7 DACFL
DUET RX DUETRX Q123 DUETRX1 BCLK 1
4 Q124 BCK DACSW
LRCLK 3
LRCK TO 2/2
DACCS 15
ML
DACCK 14
MC A
DUET CONT DACDT 13 LETP
14 DUETCONT MCLOCK MD
DF 2 AUXL
Q565 DATA
4
VDD5V X565 3 MCLK
1 11.2896MHz DAC
80 CLK_ON
IC504 BUSLP
P17_3 PCM1753DBQ
BUSLM
MCLK 16 7 DACRL
SCK VOUTL
CN104 BCLK 1
BCK
LRCLK 3
L+ BUSLP LRCK
6 DACCS 15
L- BUSLM ML
14 DACCK 14
BUS+ BUSP MC
9 DACDT 13
BUS- BUSM MD
10 DR 2
SWD ACC DATA
2
1 +B DAC
E 7 IC505
ILL
8 ILLP PCM1753DBQ
ILL-BULB
12 ILLMBULB MCLK 16 8 DACSW
SCK VOUTR
BCLK 1
BCK
LRCLK 3
LRCK
DACCS 15
ML
DACCK 14
MC
DACDT 13
MD
DSW 2
DATA
G3 VD8V
Q713
G3VD8V | B
Q715
Q729
Q
Q
VDD5V
FLSHBUSY
FLSHSCLK
FLSHRXD
FLSHTXD
F
VDCONT
CNVSS
CN604
CN602
RESET
11
16
17
18
15
3
4
DEX-MG3147ZH/XN/UC
12
1 2 3 4
5 6 7 8
u COM A
IC601(1/3)
PEG294B
WC 13
P14_3
PLLCE2 2
P9_5
SL 165
P10_7
PDO 5
P9_2
PCK 7
P9_0
PLLPCE 9
P14_6
LDET 128
AUD REF2 PDI 6
P1_5
A8V
3 IC704 1,2
REFL2
A P9_1
OPA2134UA TO 2/2
B
Q403
TUN3.3V RDSCK1 RDSCK 27
P8_4
A8V
1 IC705 3
TU33V
BA033CC0T Q404
RDSDATA1 RDSDATA 166
P10_6
VDD 1.65V
D5V
2 IC707 4
VDD1.65V
Q405
NJM2887DL3 RDSLOCK1 RDSLOCK 167
P10_5 B
VDD5V Q406
Q701 RDSHSLK1 RDSHSLK 168
BU Q702 VDD5V P10_4
TUL
FLSHRXD 48
P6_6
CNVSS 18
CNVSS
FLSHTXD 46
P6_7
DACDT C
FLSHSCLK 50
P6_5
DACCK
DOL_MUTE 66
P13_3
DOL_SEL 51
P6_4
FLSHBUSY
RDSBEEP 116
P3_0
AUXDET1 132
P1_1
CAN_OUT 29
P8_2
CAN_IN 28
P8_3
CAN_STB 32
P18_1
DUETTX1 35
P7_6
DUETRX1 31
E-VOL P8_0
IC501
PML011A LPF
LPF
16
AM Out1L
44 OUTL 3 IC506 1,2
DACFL 3
NJM4580MD
1,2 DOL_FL 39
IC507 In1L
DACRL 5 6,7 DOL_RL 37
NJM4580MD In2L
33 DOL_MUTE GA-NET D
MUTE
30 DOL_SEL IC105
DACSW 5 IC509 6,7 DOL_SW 34
In3R
SEL
17 RDSBEEP HA12241FP
TO 2/2 BA4560F MPX-RDS
45
BUSP 6 1 DOUT
BUS+ DIN1 P7_0
AUX L/R BUSM 5 BUS- ROUT
2 DIN 44
P7_1
A
LETPEE 2
IC203 1 AUXL1 12 STBY
AUXL 3 AM-level
BA4560RFV 8 IPPW 63
P5_6
Q181
BUS L/R SWD VCC ASENBO 62
BUSLP 3 P5_7
IC202 1 BUSL 3 163
BUSLM 2 CassL P15_0
NJM4580MD BDATA 160
P15_2
BRXEN 157
P15_5
BSCK 161
P15_1
BRST 141
P11_3
POWER ON RESET BSRQ 156
P15_6
VDD5V
2 IC602 1 RESET 21
RESET
S-80835CNNB-B8U CARTYP1 83
P17_0
CARTYP2 95
P16_7
ANC_CHK2 4
P9_3
DET 97 E
24 SW P16_5
SPKR3R BARI2 103
P16_3
DACCK 31
SCK SPKR1L
29 FL B TO 2/2 BARI3 104
P16_2
DACDT 32 27 RL BARI4 105
SDA SPKR2L P16_1
BARI5 106
5 P16_0
CDL+ SYSSENS 58
P13_6
MUTESENS 57
P13_7
ANC_ON 82
P17_1
BARI1 110
P12_4
G3 VD8V
ANC_CHECK ANC_CHK2
DET
SYSPWSENS SYSSENS
ANC_ON
Q713
| BU
G3LOUT
Q715
G3VD8V
VDD5V
VDD5V
Q729
A8V
Q716 VDD5V
Q717
MUTESENS
ANC_DET
CARTYP1
CARTYP2
VDCONT
VDSENS
F
BRXEN
CN602
CN601
BDATA
RESET
BARI2
BARI3
BARI4
BARI5
BARI1
BSRQ
BSCK
BRST
LOUT
VDD5
VD8
8V
5V
13
10
16
11
11
12
13
14
15
16
17
18
19
20
7
6
5
4
3
2
1
2
3
7
9
C CN902 E CN1002
DEX-MG3147ZH/XN/UC
7
13
5 6 8
1 2 3 4
LCDBL ON P1_4
129 IND2 Q802 IND2G
Q718 Q808 Q806
B DUETCONT Q719 BU Q807
118 DIMOFF
BL_ON 38 P2_7
P17_7
126 CDEJCT
ILL-BULBU H/U P1_7
125 CDLOAD
SIDE OUT P2_0
153 VOL_DOWN
Q190 P0_1
ILLMBULB Q191 VDD5V 154 VOL_UP
P0_0
151 MMIM
ILMBULB 108 P0_3
P3_2 152 MMIP
P0_2
ILLP Q192 BU
Q193
ILLON 155
LET
P15_7 176 LETDI Q114,Q115
P9_7 Q117,Q118
127 LETDI(LETINT)
P1_6
AMP SWD+B 1 LETDO
C SW+B
1 IC701 5
BU
P9_6 Q113,Q116
TPD1018F 173 TELMUTE1
6 AMPB 133 P10_0
P1_0
ANT+B P0_4
137 REM
ANTB
1 IC702 5
TPD1018F REMOTE AUDIO 8V
6 ANTPW 159 Q111
P15_3 VDD5V Q709
Q112 BU | A8V
Q712
SWD VDD Q601
SYSPW SYSPW
VDD5V
Q703
SWDVDD | BU
Q705
135
P0_6
Q707 12 ASEN
Q708 VDD5V P14_4
AMPMUTE
124 AMPMUTE1 Q109 AM
P2_1 Q110
DEX-MG3147ZH/XN/UC
14
1 2 3 4
5 6 7 8
Q805 CN801
ANTI_LED
1
LCE
2
LCK
3
LDO
4
LDI
5
RES
6
D1G IND1
7
B CN901
D2G IND2
8
B
VDD
SWDVDD 16
ILL(LEDP)
ILLB 17
ILL
18
CDEJ
9
CDLO
10
VOLDN
11
VOLUP
12
MMIM
13
MMIP
14
CN101
K-LINE
13
TEL MUTE
Q104 C
TELMUTE
14
REMOTE
22
+B 3
8V
BU
SW+B 21
ASENSE
Q103
ACC
24
RSK SIRIES
FLPREM
16
RLPREM
6 D
2 1 FLPREP
IC302 15
6 7 RLPREP
NJM4580MD 5
Q302
LMUTE
Q301
Q303
LMUTE
CN103
SWPREM SWF PRE-
7
AMPMUTE
Q109 AMPMUTE AMP MUTE
Q110 8
DEX-MG3147ZH/XN/UC
7
15
5 6 8
1 2 3 4
B KEYBOARD UNIT
A IC901
CN901 LC75700TS KEY MATRIX
LCE 18 2 KI2
19 CE KD2 S903 S941 S942 S940 S939
LCK LCK 19 3 KI3
18 CLOK KD3 ENTER SCAN SOUND SKIP+ SKIP-
LDO 20 4 KI4
17 DI KD4
LDI LDI 17 5 KI5 S943 S945 S938 S937
16 DO KD5
RES 16 6 KS1 CANCEL MENU FOLDER+ FOLDER-
15 RSET KST1
7 KS2
KST2 S916 S921,S922 S929,S930 S935,S936
8 KS3
KST3 P3 P6 CD CLOCK
9 KS4
KST4
10 KS5 S913 S920 S927,S928 S933,S934
KST5
11 KS6 P2 P5 AM DISP
IGDW(KS6)
1 KI1
KD1 S911,S912 S917 S925,S926 S931,S932
S901 P1 P4 FM AUX
VOL/POWER
5 SWVDD 4 5
VOLUP 1 2
B 9
3
VOLDN
10
S902
TUNE
MMIP 1
7
3
MMIM 2
8
A CN801
S923
CDLOAD
CDLO CDLOAD
11
S924
CDEJCET
CDEJ CDEJCT
12
C D901
ANTI-THEFT
ANT_LED
20
D902
GREEN
IND1
14
D903
LEMONYELLOW
IND2
13
IL901-IL914
ILL
3
ILL(LEDP)
4
DEX-MG3147ZH/XN/UC
16
1 2 3 4
5 6 7 8
E ANC UNIT
CN1005
A
VDD5V 15
PC_IN
14
PC_OUT
7
FLSH_IN
4
FLSH_BSY
3
FLSH_OUT
17
FLSH_CLK
18
CNVSS
16
RESET
11
ANC u-COM
IC1602
PEG342A Q1171 CN1001
34 PC_IN PC_IN ANC_SI
ROMBK2 1
33 PC_OUT
P2CE-ON
73 NEPTMR Q1181
D13
5 PC_OUT ANC_SO
REM 2
16 SCP2
NC4
17 SCP1 NEPTMR B
NC5
30 FLSH_IN Q1101
CD-IN
32 FLSH_BSY
FLCE-ON NEP
29 FLSH_OUT 10
CD-OUT
31 FLSH_CLK
702RESET
7 CNVSS
CNVSS
SCP2
RESET
Q1121
POWER ON RESET
CCSAM2
RESET
10 1 IC1601 2
VDD5V
11
S-80835CNNB-B8U
Q1701 SCP1
VDD5V MICV Q1111
CCSAM1
90 ANC_PW 12
NC15
11
XOUT
CN1002
X1601 D
16.0MHz
13 VDD5V 12
XIN
AUD8V 14
DEX-MG3147ZH/XN/UC
7
17
5 6 8
1 2 3 4
C CONTROL UNIT
CN101
CAMGEAR MOTOR CAM? CAM?
1
STAGE ASSY(SERVICE) M 2
CAM+ CAM+
HOME HOME
3
CLAMP CLAMP
4
5 IC301
BA6859AFP-Y
HE1 H1? H1? H1? 9 22
6 H1? FG
H2? H2? H2? 11
7 H2?
H3? H3? H3? 13 20
HE2 8 H3? EC
HB+ HB? 14 CAMREF
9 VH
HB?HB? H3+ 12 CAMSNS
10 H3+
H3+H3+ H2+ 10 ELVREF
HE3 11 H2+
B H2+H2+ H1+ 8 ELVSNS
12 H1+
H1+H1+ A1 6 HOME
13 A1
A1 A1 A3 4 CLAMP
14 A3
SPINDLE MOTOR M 15
A3 A3 A2 5
A2 ECR
19
REF0
LOADSWR
A2 A2 23 LOADPHT
16 VCC
CO+ CO+ LOADSWL
17
CRG MOTOR M CO?
18
CO? INISW
LOADSWR LOADSWR TEMP
19
S21 LED
20 VD Q701(1/2)
D21 L22
21
VDD SWDVDD
LOADPHT LOADPHT
22
Q21 L21 LOADSWL LOADSWL
23
S21 INISW INISW
24 Q701(2/2)
TEMP TEMP
25 VD
TH21
CONT
GND
CAMSNS CAMSNS
ELVREF ELVREF
REF0
MD PD
11
A+C AC
12
HOLOGRAM UNIT
VR
13
VREF
14 REF0
F F
15
E
VD
VDD
DEX-MG3147ZH/XN/UC
18
1 2 3 4
5 6 7 8
3,4 IC702
BR93L56RFVM-W
IC701 2
PE5595A 50
38 ROMDATA 52 ROMCK
SPDLFG
70
BVDD 3VDD
CAMREF 95 12
CAMREF X1 X701
CAMSNS 94
CAMSNS CN902
ELVREF 93
ELVREF
ELVSNS 92 13 B
ELVSNS X2 VD 18
HOME 97
HOME 17
CLAMP 4 28 CDSRQ
CLAMP CDSRQ 16
LOADSWR 58 21 CDSTBY
REF0 LOADSWR CDSTBY 15
LOADPHT 91 23 SCL
LOADPHT SCL 14
LOADSWL 57 22 SDA
INISW 43
LOADSWL
INISW
SDA
RESET
14 RESET
12
9
A
TEMP 98 49 VDCONT
TEMP VDCONT 6 CN602
Q601 VDD 8
ROUT
5
WDVDD Q602 LOUT
3
55
CDMUTE
44
SVCONT
CONT 47 59 XCS
CONT XCS
CAMREV 89 68 XASTB
CAMREV XASTB
CAMFWD 90 67 XREAD
CAMFWD XREAD
E/LFWD 32 65 XWRITE
E/LFWD XWRITE
E/LREV 31 61 XWAIT
E/LREV XWAIT
CAMVOL 6 19 XINT C
CAMVOL XINT
E/VOL 7 48 XRST
E/LVOL1 XRST
30 63 LOCK
E/LVOL2 LOCK
AD0-12
IC201
UPD63763AGJ
137 17 XCS
REF0 ADCIN CS
133 18 XASTB
REFOUT ASTB
131 19 XREAD
VREFIN READ
127 20 XWRITE
B WRITE
126 21 XWAIT
C WAIT
6 INTQ 22 XINT
9 CONT 52 3 XRST
1.5V D.VDD3 RESET
6 CAMREV 25 56 LOCK
D.VDD2 LOCK/RFOK
7 CAMFWD
4 E/LFWD 35 27
X201 XTALO ROUT
5 E/LREV 31
LOUT
9 CAMVOL
8 E/LVOL 34
XTALI IC202 D
MSM56V16160F8TKFM
0 101
FD+ RA0-11
2 103
TD+
7 107
MD+
2 105
SD+ RDB0-15
E 130
E
BD 128 71 16
D CAS CAS
LD 142 70 15
LD WE WE
PD 143 69 36
PD UDQM UDQM
AC 125 68 14
A LDQM LDQM
F 129 67 17
F RAS RAS
66 34
CKE CKE
64 18
RCS CS
63 35
C33M CLK
3.3V REG.
E
VD
1 IC203 3
3.3V
NJM2885DL1-33
VDD
2 IC703 3
3VDD
S-812C33AMC-C2N
DEX-MG3147ZH/XN/UC
7
19
5 6 8
1 2 3 4
5. DIAGNOSIS
5.1 OPERATIONAL FLOW CHART
A
Power ON
Vcc=5V
Pin10,25,47,61,69,79,90,138,164
AVcc,Vref
=5V Pin175
B
BSENS
Pin11
BSENS = L
ASENS
Pin12
C ASENS = L
A communication
start with a grill
D microcomputer
A PBUS (G3)
communication start
with a machine
Power keys
operative
E
Tuner ON
DEX-MG3147ZH/XN/UC
20
1 2 3 4
5 6 7 8
8 7 6 5 4 3 2 1 4 3 2 1
A
16 15 14 13 12 11 10 9 8 7 6 5
1: NC 9: NC 1: NC
2: NC 10 : NEP 2: NC
3: NC 11 : CCSAM2 3: NC
4: ANC R MIC+8 V 12 : CCSAM1 4: NC
5: ANC F MIC+8 V 13 : SH ANCM R GND 5: SUBW PRE+
6: SH ANC GND 14 : SH ANCM F GND 6: SH SUBW GND
7: ANC R+ 15 : ANC F+ 7: SUBW PRE-
8: ANC R- 16 : ANC F- 8: AMP MUTE
10 9 8 7 6 5 4 3 2 1 2 14 13 12 11 10 9 8 7 6 5 1
20 19 18 17 16 15 14 13 12 11 4 24 23 22 21 20 19 18 17 16 15 3 C
1 2 3 4 5 6
7 8 9 10 11 12 13 14
1 3
2
1: GA +B 8: NC
2: GA SYS ON 9: GA BUS+
3: GA BUS SH 10 : GA BUS-
1 : RF IN
4: GA AUDIO SH 11 : GA GND
2 : RF SH E
5: GA AUDIO R+ 12 : NC
3 : ANT+B
6: GA AUDIO L+ 13 : GA AUDIO R-
7: NC 14 : GA AUDIO L-
DEX-MG3147ZH/XN/UC
7
21
5 6 8
1 2 3 4
Error codes
A In the case where the CD is disabled or stopped by error during operation, the mechanism enters the error
mode. The causes of errors are given with numbers.
( represents a number.)
DEX-MG3147ZH/XN/UC
22
1 2 3 4
5 6 7 8
DOORCLS
CAMRST error
DEX-MG3147ZH/XN/UC
7
23
5 6 8
1 2 3 4
Claw error
ELV error
Code Error Error description, upper (1 and 2 digits)
Timeout occurs before the brake position of the elevator is reached (ascending) at the
0xb0
time of mechanical operation given in the left column.
B
Timeout occurs before the brake position of the elevator is reached (descending) at the
0xb1 "DISCSEL
time of mechanical operation given in the left column.
(Load to
Overrun/under run error of the elevator at the time of mechanical operation given in the
0xb2 Load)"
left column.
100-time attempts of the elevator pulse driving have failed at the time of mechanical
0xb3
operation given in the left column.
Timeout occurs before the brake position of the elevator is reached (ascending) at the
0xb4
time of mechanical operation given in the left column.
Timeout occurs before the brake position of the elevator is reached (descending) at the
0xb5 "DISCSEL
time of mechanical operation given in the left column.
C (Load to
Overrun/under run error of the elevator at the time of mechanical operation given in the
0xb6 Play)"
left column.
100-time attempts of the elevator pulse driving have failed at the time of mechanical
0xb7
operation given in the left column.
Timeout occurs before the brake position of the elevator is reached (ascending) at the
0xb8
time of mechanical operation given in the left column.
Timeout occurs before the brake position of the elevator is reached (descending) at the
0xb9 "DISCSEL
time of mechanical operation given in the left column.
(Play to
Overrun/under run error of the elevator at the time of mechanical operation given in the
0xba Load)"
D left column.
100-time attempts of the elevator pulse driving have failed at the time of mechanical
0xbb
operation given in the left column.
Timeout occurs before the brake position of the elevator is reached (ascending) at the
0xbc
time of mechanical operation given in the left column.
Timeout occurs before the brake position of the elevator is reached (descending) at the
0xbd "DISCSEL
time of mechanical operation given in the left column.
(Play to
Overrun/under run error of the elevator at the time of mechanical operation given in the
0xbe Play)"
left column.
100-time attempts of the elevator pulse driving have failed at the time of mechanical
0xbf
E operation given in the left column.
*0xb0 to 0xb3 only for the self test under test mode.
Insertion/ejection error
Code Error Error description, upper (1 and 2 digits)
0xe0 CAMRST Door is opened at the time of CAMRST (door opening/closing error).
0xe1 WTLOAD "Load error (Forced eject -> DOORCLS -> DOOROPN, repeated by five times)"
0xe2 EJCTION "Eject error(Forced eject -> DOORCLS -> DOOROPN, repeated by five times)"
0xe3 SEJPCK "SEJPCK error (Forced eject -> DOORCLS -> DOOROPN, repeated by five times)"
0xe4 HLFLOAD "HLFLOAD error (Forced eject -> DOORCLS -> DOOROPN, repeated by five times)"
F 0xe5 DINSRDY "DINSRDY error (Forced eject -> DOORCLS -> DOOROPN, repeated by five times)"
0xe7 RELOAD "RELOAD error (Forced eject -> DOORCLS -> DOOROPN, repeated by five times)"
DEX-MG3147ZH/XN/UC
24
1 2 3 4
5 6 7 8
DEX-MG3147ZH/XN/UC
7
25
5 6 8
F
E
B
A
D
C
26
1
1
release
6. SERVICE MODE
2 Only the serial No. display before the ANTI THEFT is released is available
* Only before the ANTI
THEFT is released
1
2
2
DEX-MG3147ZH/XN/UC
brightness
While every segment of LCD is turned OFF, the step value is not changed even if the TUNE key is
operated. However, the value that is changed while every segment of LCD is turned ON is saved.
3
3
ILL dimmer duty display 4 ILL step value display ILL dimmer STEP value is displayed (for TA0A, data is acquired from B-CAN)
Vehicle speed pulse 5 Vehicle speed import The vehicle speed is displayed (for TA0A, data is acquired from B-CAN)
GA-NET connection check The function address of equipment that is connected by GA-NET is displayed
(GA-NET)
GA-NET connection check
Communication The function address of equipment that is connected by GA-NET is displayed
6 (GA-NET)
connection check 6
(Toggle operation) Non-GA-NET (DSP) The connection check of DSP is implemented, and the result is displayed
display
Non-GA-NET (compass) The connection check of compass is implemented, and the result is displayed
Non-GA-NET (LCD) The connection check of LCD is implemented, and the result is displayed
AM key long press
AM receiver sensitivity measurement is implemented, and the receiver sensitivity level is displayed.
(5s) AM switching
The frequency of receiver sensitivity measurement is changed to last frequency
AM or FM (If it is an AM/FM)
FM key long press
Radio receiver long press FM receiver sensitivity measurement is implemented, and the receiver sensitivity level is displayed.
(5s) FM switching
sensitivity (5s) The frequency of receiver sensitivity measurement is changed to last frequency
(If it is an AM/FM)
Selector rotation Frequency change The changed frequency is displayed for 2 seconds
4
4
5
DRAM remaining amount
1 (default) The DRAM remaining amount is displayed
display
Number of mechanism
2 microcomputer The number of CD mechanism microcomputer communication errors is displayed
communication errors
CD investigation mode CD or Number of DISC change
3 The number of DISC change errors is displayed
(DRAM remaining CD/AUX long errors
amount display) press (5s) 4 Thread servo error history The number of thread servo errors is displayed
5 Servo diagnosis The status of CD mechanism is displayed
2 to 5 long press (5s) History clearance Each error history is cleared
SEEK/SKIP + Track up event
SEEK/SKIP - Track down event
VOL Volume control
B-CAN status display The status of B-CAN is displayed
B-CAN connection This is the function to display VIN No., however, the import from B-CAN is not implemented for
6
6
DEX-MG3147ZH/XN/UC
1+3+5+POW keys pressing
Name of function Key Key in mode Target of check General description of function
7
7
System microcomputer
System microcomputer Ver System microcomputer Ver. is displayed
display
8
27
E
A
D
C
F
B
1 2 3 4
DEX-MG3147ZH/XN/UC
28
1 2 3 4
5 6 7 8
Contents
Test Mode In A
TRK MIN SEC
Display
CD
Source ON
SCAN 3 2 5
Power ON Power ON RF AMP New Test Mode
(T.Offset adjustment required) (T.Offset adjustment not required) Gain select *1
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99 xx xx xx
B
SCAN 3 5 1 SKIP+ SKIP- 2 DISP 4
Power OFF Focus Close Focus Mode Tracking Servo CRG+ CRG- Auto Adjustment Jump OFF Focus Close
S-curve Measurement Select *2 Close Display Select *3 & TBAL Adjustment
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC TRK MIN SEC TRK MIN SEC
91 91 91 0x 0x 0x ( 99 99 99 ) ( 99 99 99 ) ( 99 99 99 ) xx xx xx xx xx xx 91or81 91or81 91or81
2
SCAN
Tracking Open
Power OFF
8x 8x 8x
TRK MIN SEC 9x 9x 9x
*3) F.Offset Display -> T.Offset Display -> Original display 2 RF gain select / Offset adjustment display / T.Balance adjustment /
T.Open
3 F.Close, S.Curve /Rough Servo & RF AGC / F, T, RF AGC
*4) 1TR /4TR / 10TR / 32TR / 100TR 4 Error occurrence time
Start of Measurement (30 s) / Interruption of Measurement (max. 30 s) /
*5) Single TR -> 4 TR -> 10 TR -> 32 TR -> 100 TR -> CRG Move Display of numbers of C1 & C2 errors (after completion of measurement)
9X(8X):91(81) 92(82) 93(83) 94(84) 95(85) 96(86)
DISP Jump OFF
5 Focus Mode Select / Tracking Close / CRG, TR Jump Select
*6) TRK/MIN/SEC -> F.AGC Gain -> T.AGC Gain -> RF AGC Gain
E
TRK = 0 (Completion of measurement)
*7) TRK/MIN/SEC -> S.Curve -> C1 error count -> C2 error count
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
?? ?? ?/ xx FF FF xx xx xx xx xx xx
(33 -> 0)
TRK >0 (Between measurement)
After pressing the eject key, do not press any other key than [Eject] key, till the disc is ejected.
TR Jump operations except for 100TR Jump continues even after you release the relevant key.
For CRG Move and 100 TR Jump operations, the system goes to the Tracking-Close status, when you release the relevant key.
Upon turning the power Off/ON, the Jump Mode is reset to Single TR(91), and RF AMP Gain setting is reset to 0 dB, while the automatic
adjusted values goes back to the initial values.
If you are in the middle of measurement, the measurement is terminated.
DEX-MG3147ZH/XN/UC
7
29
5 6 8
1 2 3 4
FCH
Test Mode In
trk** min** sec**
06H
Source CD
trkFF minFF secFF
B
B3H
CAM MOTOR ELV MOTOR CLAW MOTOR Endurance Test Changing the
Selection Selection Selection Selection step width Mecha Test Out
C
trk72 min01 sec** trk72 min02 sec** trk72 min03 sec** trk72 min** sec** trk72 min** sec** trk** min** sec**
72 00 20 72 00 2C 72 00 26 72 00 2F 72 00 23
Load Pht
E
Load Right Sw ON
Load Left Sw ON
Load Init Sw ON
DEX-MG3147ZH/XN/UC
30
1 2 3 4
5 6 7 8
7. DISASSEMBLY
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
- Removing the Grille Assy (Fig.1)
A
2
1 Remove the two screws. 2 2
1 1
2 Remove the seven screws and then
remove the Grille Assy. 2 2
2 2
D
1 Remove the four screws. 1 1
1
1 E
DEX-MG3147ZH/XN/UC
7
31
5 6 8
1 2 3 4
1 1
Fig.5
1 2
DEX-MG3147ZH/XN/UC
32
1 2 3 4
5 6 7 8
3 B
1 1
2 2
* Please refer to Mechanism Manual (CRT3467) for removing module part of CD mechanism.
Three GGF1538 are necessary to build up CD mechanism.
C
DEX-MG3147ZH/XN/UC
7
33
5 6 8
1 2 3 4
DEX-MG3147ZH/XN/UC
34
1 2 3 4
5 6 7 8
DEX-MG3147ZH/XN/UC
7
35
5 6 8
1 2 3 4
9.1 EXTERIOR(1)
B
A
E
B
18%
DEX-MG3147ZH/XN/UC
36
1 2 3 4
5 6 7 8
21 Holder CNV9355
22 Knob Unit CXC7102
23 •••••
24 Button Unit CXC7103
25 Slider CNV9781
26 Slider CNV9780
27 •••••
28 •••••
29 Sheet CNN1923
D
30 Sheet CNN2128
31 Sheet CNN2129
32 Sheet CNN2130
33 Sheet CNN2131
34 Sheet CNN2132
35 Sheet CNN2133
DEX-MG3147ZH/XN/UC
7
37
5 6 8
1 2 3 4
9.2 EXTERIOR(2)
A
A
19 B D
E
C
F
E
19
E
C
D I A
G
D 18%
A
H
F
G
C
DEX-MG3147ZH/XN/UC
38
1 2 3 4
5 6 7 8
11 Bracket CND4218 B
12 Frame CND3719
Caution(When you replace the tuner amp assy.)
When you replace the tuner control unit assy in any case.
13 Insulator CNN1437
You must use IC (S-93C66BD0I-J8) that on replaced tuner
14 Insulator CNN1714
control unit assy instead of new tuner assy one.
15 Guide CNV9331 Because this IC had nessesary data inside.
( model name, ANC setting etc.)
16 Guide CNV9576 If this IC was broken you must replace whole head unit.
17 Tuner Amp Assy CWN2978
18 Screw BMZ30P060FTC
19 Cushion CNN1930
20 Connector(CN104) CKM1208
C
21 Plug(CN102) CKM1510
22 Plug(CN101) CKM1518
23 Plug(CN801) CKS3540
24 Connector(CN602) CKS3859
25 Connector(CN604) CKS4374
26 Connector(CN103) CKS5676
27 Connector(CN601) CKS5753
28 Connector(ANT401) CKX1072
29 Holder CND3720
D
30 Holder CND3721
31 Holder CND3724
32 Holder CND3725
33 Holder CND3726
34 FM/AM Tuner Unit(Y401) CWE2042
35 Holder CND2144
36 Screw PBZ30P060FSN
37 ANC Unit CWN2740
38 Plug(CN1001) CKM1511 E
39 Connector(CN1005) CKS4374
40 Connector(CN1002) CKS5755
41 Holder CND3722
42 Screw PBZ30P060FSN
43 Chassis Unit CXC8505
44 Screw IMS20P025FTC
45 Screw IMS26P050FTB
46 CD Mechanism Module(Service)CXX2171
F
47 •••••
48 •••••
49 IC(IC705) BA033CC0T
DEX-MG3147ZH/XN/UC
7
39
5 6 8
1 2 3 4
DEX-MG3147ZH/XN/UC
40
1 2 3 4
5 6 7 8
11 Gear CNV8946 B
12 Gear CNV8296
* 13 Gear CND2548
14 Variable Resistor(VR13) CCW1029
15 Gear CND2563
16 Arm CNV8312
17 Case CND3803
18 Stair CND2556
19 Stair CND2555
20 Stair CND2554
C
21 Spring CBH2841
22 Cam CNV8779
23 Cam CNV8778
24 Cam CNV8311
25 Cam CNV8309
26 Arm CNV9327
27 Spring CBH2851
28 Washer CBF1094
29 Holder CNV8304
D
30 Washer YE15FTC
* 31 Arm CND3709
32 Screw(M2 x 2.5) CBA1823
33 Washer CBF1064
* 34 Gear CND2560
* 35 Gear CND2561
36 Spring CBH2838
37 PCB Assy CXC3142
38 ELV Motor Assy(ELV)(M2) CXC5922 E
* 39 Lever Unit CXC3956
40 Tray Assy CXC7343
46 Screw BMZ20P025FTC
F
47 Screw IMS26P025FTC
48 RPS PCB Assy CWX2986
49 Cam Motor Assy(CAM)(M1) CXC5920
DEX-MG3147ZH/XN/UC
7
41
5 6 8
1 2 3 4
8200P
8200P
B
A 2/2
CD:0.28 dBs A 2/2
A 2/2
C
CN902
E
CN1002
A 2/2
SYSTEM CONTROLLER
D
PEG294B
A 2/2
3R9K
1R2K
B CN901
A 1/2
DEX-MG3147ZH/XN/UC
42
1 2 3 4
5 6 7 8
CD:-0.31 dBs
AM:-17.65 dBs
FM:-5.65 dBs
AUX:-0.51 dBs
B
CD:0.19 dBs
AM:-15 dBs
FM:-11 dBs
AUX:-1.01 dBs
A 2/2
AUX:-0.28 dBs
A 2/2
33/16
CD:11.60 dBs
AM:-5.75 dBs
56
FM:-6.25 dBs E
AUX:11.40 dBs
56
A 1/2
DEX-MG3147ZH/XN/UC
7
43
5 6 8
F
E
B
A
D
C
44
A-a A-b NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
A-b 1/2
Symbol indicates a capacitor. 2.2 t 2R2
1
1
CD:-0.31 dBs
AM:-17.65 dBs
FM:-5.65 dBs
AUX:-0.51 dBs
2
2
DEX-MG3147ZH/XN/UC
3
3
CD:0.19 dBs
AM:-15 dBs
FM:-11 dBs
AUX:-1.01 dBs
4
4
5
5
AUX:-0.28 dBs
6
6
33/16
CD:11.60 dBs
AM:-5.75 dBs
56
FM:-6.25 dBs
AUX:11.40 dBs
56
DEX-MG3147ZH/XN/UC
7
7
2
8
8
A-a A-b
A-b 1/2
45
E
A
D
C
F
B
F
E
B
A
D
C
46
A-a A-b
A-a 1/2
A-b 1/2
1
1
AM:-14 dBs
FM:-10 dBs
8200P
8200P
2
2
A 2/2
CD:0.28 dBs
DEX-MG3147ZH/XN/UC
A 2/2
3
3
A 2/2
C
CN902
1
4
4
E
CN1002
A 2/2
SYSTEM CONTROLLER
E
CN1002
A 2/2
SYSTEM CONTROLLER
5
5
PEG294B
6
6
A 2/2
DEX-MG3147ZH/XN/UC
7
7
3R9K
2
1R2K
8
8
B CN901
A-a A-b
A-a 1/2
A-b 1/2
47
E
A
D
C
F
B
1 2 3 4
A
A 2/2 TUNER AMP ASSY(POWER SUPPLY) : The power supply is shown with the marked box.
A1
B
A1
C
A 2/2
DEX-MG3147ZH/XN/UC
48
1 2 3 4
5 6 7 8
marked box. A
A 1/2
B
A 1/2
C
A 1/2
A 1/2
D
A 1/2
A 1/2
A 1/2 F
A 2/2
DEX-MG3147ZH/XN/UC
7
49
5 6 8
1 2 3 4
A 1/2 CN801
A.SEL
RETURN
E
VFA1105W-4C93B
B
DEX-MG3147ZH/XN/UC
50
1 2 3 4
5 6 7 8
B KEYBOARD UNIT
FOLDER+ FOLDER-
TITLE
B
DEX-MG3147ZH/XN/UC
7
51
5 6 8
1 2 3 4
A C-a
M1
CAM MOTOR
CXC5920
S
S
S
STAGE ASSY(SERVICE)
C
C
T
C
CXX2231
2 F
3 F
5
T
F
F
D RPS PCB ASSY T
T
T
R11 5R6K
C VR11 CCP1442
1k(B)
9
R14 5R6K
VR13 CCW1029
10k(B)
6
7
R13 5R6K
(CXC3142)
PCB ASSY
VR12 CCP1442
1k(B)
R12 4R7K
M2 @
ELV MOTOR S
CXC5922 S
S S
D
4
*
E C
F
S
1
T
S
T 8 C
T
C
F
F
C D
DEX-MG3147ZH/XN/UC
52
1 2 3 4
5 6 7 8
C-b A
C CONTROL UNIT
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
F
T
C
S
^
D
&
A 1/2
CN602
%
$
#
4MHz
C
DEX-MG3147ZH/XN/UC
7
53
5 6 8
F
E
B
A
D
C
54
C-a C-b
C-b
CONTROL UNIT
1
1
1
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
2
F
T
C
2
2
DEX-MG3147ZH/XN/UC
3
3
4
4
5 6 7 8
CN602
A 1/2
A
C
^
&
C-a C-b
D
#
%
$
4MHz
3 4 C-b
DEX-MG3147ZH/XN/UC
7
55
5 6 8
F
E
B
A
D
C
56
C-a C-b
C-b
1
1
C-a D
M1
CAM MOTOR
CXC5920
1
S
S
S
2
C
C
T
C
2
2
CXX2231
T
2 F
3 F
5
T
STAGE ASSY(SERVICE)
T
DEX-MG3147ZH/XN/UC
F
3
3
F
F
D T
RPS PCB ASSY T T
R11 5R6K
VR11 CCP1442
1k(B)
9
R14 5R6K
VR13 CCW1029
10k(B)
6
7
4
4
R13 5R6K
VR12 CCP1442
1k(B)
R12 4R7K
(CXC3142)
PCB ASSY
M2 @
5 6 7 8
A
3 4 C-b
S
@
C
C
S
4
C
S
T
C
F
8
1
F
F
T
T
S
S
S
C-a C-b
D
E
R12 4R7K
F
ELV MOTOR
B ASSY
CXC5922
C3142)
C-a
M2
DEX-MG3147ZH/XN/UC
7
57
5 6 8
1 2 3 4
A
E-a
A 1/2
CN601
Engine rotational speed count
Cylinder distinction(2)
E
Cylinder distinction(1)
E
DEX-MG3147ZH/XN/UC
58
1 2 3 4
5 6 7 8
E-b A
E ANC UNIT
E
DEX-MG3147ZH/XN/UC
7
59
5 6 8
1 2 3 4
ANC UNIT
A
E
C
E-a E-b
E-b 1
DEX-MG3147ZH/XN/UC
60
1 2 3 4
5 6 7 8
E-a E-b
D
2 3 E-b
DEX-MG3147ZH/XN/UC
7
61
5 6 8
1 2 3 4
E-b 1
C
E-a E-b
E-a
DEX-MG3147ZH/XN/UC
62
1 2 3 4
5
5
2
A 1/2
CN601
6
6
Cylinder distinction(2)
DEX-MG3147ZH/XN/UC
Cylinder distinction(1)
7
7
3
8
8
E-a E-b
E-a
E-b
63
E
A
D
C
F
B
1 2 3 4
10.6 WAVEFORMS
- CONTROL UNIT Note: The encircled numbers denote measuring points in the circuit diagram.
DEX-MG3147ZH/XN/UC
64
1 2 3 4
5 6 7 8
DEX-MG3147ZH/XN/UC
7
65
5 6 8
1 2 3 4
*note
RAM memory usage monitoring function
The memory usage within the RAM can be monitored by tracking the voltage levels at the test points,
C RAM0,RAM1,RAM2, on the PCB.
Divide the total volume of the RAM by 7, and express the memory usage in 3 bits (3 binary digits),
RAM0,RAM1,RAM2. The RAM0 indicates the least significant bit. If then the combination of the voltage levels
measured at the RAM0,RAM1,RAM2 is converted to an octal number, X (Oct), the memory usage within the RAM
should be expressed by "X (Oct) / 7".
It is also possible to measure the memory usage within the RAM in voltage (appx 5 V at max),
by adding the R/2R ladder resistance circuit detailed in the diagram on the right.
Point
R R
2R 2R 2R 2R
Vmemo
Fig.1
DEX-MG3147ZH/XN/UC
66
1 2 3 4
5 6 7 8
DEX-MG3147ZH/XN/UC
7
67
5 6 8
1 2 3 4
E
to check with the schematic dia- R130
5
D104
gram. C341 C342
1 C
2.Viewpoint of PCB diagrams Q109
3 15
E
E C340
Connector Capacitor D117
150 D103 1 5
R105
R104
R131
R128 Q102
C131
R127 Q114
R143
SIDE A C130 Q115
E
Q
B
140 C102
R142E
R13
R139
SIDE B R141
Q117 R144
P.C.Board Chip Part L101 R140
R145
D119
E
D120
130 C113
R10
15
10
1
C335 C716
R322
R735
E Q303 R344 R346
E Q301 5 1
R345
J602 R343 Q306
C 110 C702 5
Q701
Q304
CN
E
R706 C701 E
E Q305
R705 1 5
C703
100 R701
D703
C709
E C252
D702 C251
Q702
R573
90 Q710
C710 C311 C306 C325 C329
R572
D706 C578
R722 5
E
C551
C307 C312 C328 C324 C563 IC509 C577
R717
80 R723
R718 R568
1 R570
C547
E
R724
70 R721
Q712 1
Q711
1
C571 C569
E
R307 R325 5
60 C319
R301
Q812 R829
R330
R324
C522
E
C712
1 C557
R518 C559
C707 C521
R556
50 Q714
C713
R558
R511
R508 R504
C737
R517 C519
E
R774 R510
C730
C732 C540
E
20
15
R516
R507
40
10
C735
25
R732
Q715
R776 R731 IC501
5
R515 R503
E
30
R777
R730
40
35
30 Q729
C518
C517
R728
E
R729 C724
R727
R775
D722 D721 R754 R748 R755 R749 R
20 R712
R758
Q704 E Q725 E Q724 E
F
10
A Y 0 X 10 20 30 40 50 60 70
DEX-MG3147ZH/XN/UC
68
1 2 3 4
5 6 7 8
SIDE A
ANTENNA
ANT401
CAR HARNESS
CN104 CAR HARNESS 1
CAR HARNESS 10
CN102 C415
C142
CN101 C194 15 20 L406
ZNR402
5 1 C416
3 15 20 24 4 R401
R185
R216
R215
R214
R217
R814
1 5 10 14 2 R220 1 5 10 C401
R218
R180 R593 R591 R118
R813 R221
1
D116 C144
Q114 C114 R219
R143
E
Q116 R146 C260 C184 L402
Q115 R592 C143
C210 C183 R188 C145 R235 B
C212
D121
5
R147
D123
5
E
R138 E Q113
R142E C261
IC105 D122 C106 R236
E
C209
R179
C211 L104 C118
15 5 1
1
R148
R139 Q118
1
R141 C119
Q117 R144 C185 R237
R145 L181 R200 Y401
R140 Q103 R107 C104
R226 R225 R189
5
C117
CN603 CN401 L401
E
D119
E
D106 C116
D120 D105
R224
C132
R106 IC202 C121
C718
R101
C717 C123
1
10
R736 L161 R165R162 R240
C701 R160 5
D124
R163 R270 R269 C403
15
R161 R276
C716 C231 C122 C270 R238
R735 C223
C505 C230 C244 C243
C229 R251 5R208
C502 C501 R254
C504 R250
R213
C204
10 20 R253 IC201
C233 C221 L403 C
R204
R205
C232 R394
C208
CN601 R212 C205 C203
1 R203
C202
Q393 R393 R392
E E E
C206 R211 R202 C391
IC707
R678
5
D715
C744
C743 C407
R573 R779
C602 R772
R572 CN604
1
578 C742
10
5 IC706
C551 TC601 L405
R612 C601IC602 R607
15
R771
R809
R685
R608
R434
5
C577
R609
C509 C741
R610
R611
R603
20
E
1
1 D601 Q412
R552 R806 R623 R435
X601 C738
1 R570 R810 R624
1
C547 R807
R548 R625
C572 C570 R553
IC505 R549 R808 R622 D714 D
5
C550 R416
C552 C603 R614
R545 C549 R634 R686
IC508 R661
R544 40 30 20 10 1
1
R540
15
1 L504 C410
50
R543 C414
170
R665
C548
R567 R569 R667 R666 R415
R559C543 R538 C545 R668 R413
R557
R537 R650 C413
60
C560 C558
1
R417
R636
160
R533
15
IC503 R535
5
2 C544
70
R509 L606
C541 R631 R660 R584 R825
R586
1 C557 C531 C660 C632
R670
80
C559
140
C740
R639
1
C540 L603 E
R588
R590
20
15
R651
R657
R654
R655
R675
R687
C580
C524
R673
R676
R674
C564
R507 C533
10
5
C530 L531 R679 D691 D693 R656
C739 IC705
R688 L604
C528 L502 C581
IC501 C535 R120 R812
R524 C538 C532
5
C515
C508 C509 R691
C691
Q804 CN602 CN902
40
35
R692 Q120 E 1 1 E
1
Q808
C518
C517
R693 1 5 15
C626 C624
R696
Q805
IC603 C111
R167
1 1
R695
R821 R804 C627 L605
5
R1 D602
R801
R758 C721 10 20
Q724 E Q723 E Q721 E
C720 1 5 15
CN801 B CN901
FRONT F
70 80 90 100 110 120 130 140 150 160 170 180 190
A
DEX-MG3147ZH/XN/UC
7
69
5 6 8
1 2 3 4
A
D107R109 C141
C192
R110
C719
R737
R181 R182 C193 C187
C189 C
C135 L701
C133 R223
R155 R152
R151
R154
R150
C128 D711
C134 C181
R153 Q718 C182
C120
E
R157 C125
R156 D129
R738
Q181 D182
C190 D127
E
R158 L102
R739
R740
D181
B R159 D128 Q719
L103 R177
E
R274 R193 R186
D130 L190 R741
R176
R191 C127
C271 D190 R231 R2
R275 Q190 R175
R192
R171
R149 C218
R174
E
C402
E
D271 Q124
R256 R257 C191
C126
R451 R255 R173
R229
C214
R115 D110 Q123
E
C235 R258
C419 R194 Q122 R170 R172
E
R116 R168 D131
C234 C124 Q121
R261 R169
E
R246
E
R402 R260 C226
Q105
R403 R1
C225 1
R247
R404 R117
R405 R242 C227 R248
R406 IC203 R252
R407 R266 C239 R249
R436 R241 5
R267
R280 R244 C224 C228
E
C404 R408
C412
C406
Q403
R419
E
Q404 R123
E
R119 C630
Q405 R420
E
R421 C605
Q413 R847 R604
Q411
E
Q406 R422
E
R613
E
C408 L601
R410 R834
R431 R620
R411 R433 R621 R633
C409
D C417 C631
E
Q402 R658
Q409 R428
E
R615
C607
C616
R681
R617
R616
E
R583
E
R574
R677 R653
R426
Q407 C629
C611
D401
R425
D402 R585
R576 R596
C507 R822 R637 R646 R594 R577
C110 C615
R562 R500
R832 R600
R823 R598 R595 R597
C610
R648 R830
R587 R578 C662
R628 R589 C618 R580
C612 C663 C584
C614 R579 E
C613 C661 L562
R601 L602 R83
R680
R629
C506 L565
R627 Q565
R602
E
R563
C625
R817 R818 R816 L810
R831
C812
A 200 190 180 170 160 150 140 130 120 110
DEX-MG3147ZH/XN/UC
70
1 2 3 4
5 6 7 8
A
170
C192
R223 C236
C343
R356
150
1
R358
C181 R357
Q307
5
C182 D109 C333 C331 C314
1
R355
81 D182 C129
R114
E
D181
D108
C316
140
R178 B
R133
86 R113
R135
D118
7 R231 R232 C237 R136 Q111
L191 R112 Q104 E
75
E
R195
24
R149 C218 C219
R196 R197
R134 E 130
C112 Q112 R348
E
C338
R353
R229
C213
C214
R228
1
C619 IC305
31 R198 C339
5
Q121
E
R349 D704
E
R352
R351
R350
Q192
Q602
D301
120
C334
R199 C623
E C336
C622 Q603 C620
C621
C337
Q606 E R347
E
Q604
E
Q605 110
E
R699
IC205 R342 R339 R317 R318
R698
R689 D701
R690
R697 R703 R704
R702
90
C575
R571
C576
C568
R566
80
R847 R604 C566
C309 R819
R337
C326
R315
R565 R826
R834 R827
R314
R633
E
R310
C574 C579 R336 R828 D
70
R313
R658
D811
C323
R332
R309
C305
C608
R308
C554
C322
R331
C304
C555 60
R574
R653
C629 C562
R596 R554
R577
R562 R500
R832 R600
R595 R597
610 C520
R531
R830
R578 C662 C525 R560 D716
50
R530 R528
C663 C584 R519 R561
L561
R599
E
R505 C511
C733 Q717
D501
R513 R502 C734
R501
R512 C510
30
C708
C705
R710
R708
R709
R711
C706
R713
L810 Q708
E
E
Q722 Q720
E
R745
E
R831
C812 R753 R752 R747 R746 R744
E
R714
Q705
C722
R743 Q707 Q703
20
10
Y F
0
0 110 100 90 80 70 60 50 40 30 20 10 X A
DEX-MG3147ZH/XN/UC
7
71
5 6 8
F
E
B
A
D
C
72
B
B
1
1
KEYBOARD UNIT
1 1 2 3 4 5 6 6
11.2 KEYBOARD UNIT
2
2
100
LOAD C910 EJECT
90 S901
S936
S925 S926 S927 S928 S929 S930 S931 S932 S933 S934 S935
80
FM AM CD AUX TITLE CLOCK
70
VOL/PWR
S937 S938 S939 S940
60 S941 S942
DEX-MG3147ZH/XN/UC
FOLDER DOWN FOLDER UP SKIP DOWN SKIP UP
50
SCAN A.SEL
3
3
S902
1
40 S943 S945
4
4
SIDE A
B
F
C
D
A
73
B
SIDE B
8
8
IL903 IL902
R905
IL904 R904 IL901
R903 R902 110
R906
R907 100
IL912 IL911 IL908 IL907
R901 C901 C902
R922 90
R914 R921 R910
R931 R915
IL914 R932
R933
R911 IL905 80
R934 C907 D904
R935 R944
R936 R942
7
7
20 15
1 5 10
R916
R937
R938
R943
C909
70
R917 R939
DEX-MG3147ZH/XN/UC
R940 C906
L901 IL909
R941 IC901 C905
C908 R923 60
C903
IL913 C904 IL906
R924 50
R908
R946
R947
R948
R945
R949
R909
L902 40
CN801
CN901
10 20 IL910
30
1 5 15
A
R912 20
6
6
R913
10
Y
20 10 0
280 270 260 250 240 230 220 210 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 X
KEYBOARD UNIT
5
5
B
1 2 3 4
10
20
30
40
0
X
(SERVICE)
STAGE ASSY
10
B
A
CN602
20
(SERVICE)
STAGE ASSY
C
30
40
D
50
E
60
70
C
DEX-MG3147ZH/XN/UC
74
1 2 3 4
5 6 7 8
Y
40
30
20
10
0
X
10
B
20
C
30
40
D
50
E
60
70
C
DEX-MG3147ZH/XN/UC
7
75
5 6 8
1 2 3 4
150
140
CAR HARNESS
10 15
10
C1367
CN1001
D1133
R1134
R1132
C1113
R1112
C1133
D1132
R1133
D1111
R1113
CN1003
130 Q1131
Q1111 R1131
D1131
1 5
L1301
C1369
1 5
1
R1391
1
R1111
D1121
D1141
R1142
C1123
R1122
C1103
R1123
R1143
C1143
R1103
R1102
C1185
R1392
C1186
L1185
R1185
C1184
C1187
L1302
D1101
L1186
R1186
Q1121 Q1141 Q1101 R1101 R1374 R1371
B R1141
1
1
120 R1372 R1373
R1315
R1313 R1307
C1307
R1309 C1305 R1303 C1301 C1302
R1317 5 5 5
C1303
C1309
R1321
IC1303 IC1302 IC1301 C1706
100 C1703
C1702
R1701
C D1701
90
C1701
80 C1704
C1352
R1378 R1356 C1358 C1362
70 C1354 C1356
R1358 R1368 R1364
5 5 5
5
R1352
50
CN1005
10
R1612
15
D1601 R1631
5
R1611
20
1
1
R1671 C1605
40 R1670 C1606
C1604
R1669 IC1601
30
50
45
40
35
R1668
R1667
25
X1601
55
L1601
20
R1624
60
R1664
30
15
E R1660
IC1602
R1645
65
10
R1644 R1623
R1643
70
R1642
5
R1641
R1715
75
R1640
R1639
100
80
90
85
95
20
R1606
R1620 Q1701
1
10
Y
F
0 10 20 30 40 50 60 70 80 90 100 110
X
E
DEX-MG3147ZH/XN/UC
76
1 2 3 4
5 6 7 8
150
140
R1163
R1162
D1161 D1162 D1152
R1154
1
130
E
E
R1151 R1152 Q1151
D1151
C1112
R1164
C1111
C1132
C1131
C1122
C1121
C1102
C1142
C1141
C1101
C1370
10 C1368 C1182 B
R1121
R1380
R1382
C1183 120
R1302
R1301
R1171
R1173
R1172
D1171
R1174
E
C1171
D1302
CN1004
D1182
D1181
Q1171
R1183
R1182
R1181
C1181
R1379 R1381
D1702 R1712 R1319
C1705 D1301 R1320
110
R1305
R1311
R1306
R1312
Q1181
E
1 5 15 R1184
R1369
R1203
R1370 R1204
R1201
100
10 20
C
90
A CN1002
CN601
1 5 15 80
R1202
70
R1362
C1360
R1354
R1376
R1366
R1361
R1375
C1359 R1353
R1365 60 D
50
R1613 R1625
R1630 R1633
R1614 R1651
R1628 R1632
40
R1626
R1627 R1634 R1647 R1665
R1648 R1656
X1602
C1602 C1603 R1674
R1663 R1673
C1608
C1610
R1655 R1666 R1672 30 E
R1654 R1657
R1609
C1601 R1646
R1610
R1659
R1658
C1607
R1621 C1609
R1662 R1653 20
R1622 R1652
R1602
R1603 R1661
R1607
10
Y
F
110 100 90 80 70 60 50 40 30 20 10 0
X
E
DEX-MG3147ZH/XN/UC
7
77
5 6 8
1 2 3 4
PCB ASSY
20
VR13
10
Y M M2
0
10 20 30
X
D
DEX-MG3147ZH/XN/UC
78
1 2 3 4
5 6 7 8
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
IC 601 (A,127,59) IC PEG294B
Unit Number : CWN2978 IC 602 (A,137,84) IC S-80835CNNB-B8U
Unit Name : Tuner Amp Assy
IC 603 (A,118,28) IC S-93C66BD0I-J8
Unit Number : IC 701 (A,65,120) IC TPD1018F
IC 702 (A,85,125) IC TPD1018F
Unit Name : Keyboard Unit IC 704 (A,43,35) IC OPA2134UA
C
IC 705 (A,180,36) IC BA033CC0T
Unit Number : CWN2740
IC 707 (A,157,96) IC NJM2887DL3
Unit Name : ANC Unit Q 102 (A,35,150) Transistor 2SC4081
Unit Number : CWX3473 Q 103 (A,79,133) Transistor 2SC4081
Q 104 (B,80,132) Chip Transistor 2SA1576A
Unit Name : Control Unit Q 105 (B,134,119) Chip Transistor 2SA1576A
A
Unit Number : CWN2978
Q
Q
114
115
(A,75,143)
(A,71,143)
Chip Transistor
Chip Transistor
DTC124EUA
2SA1576A
Q 116 (A,78,143) Transistor 2SC2713
Unit Name : Tuner Amp Assy Q 117 (A,73,134) Transistor 2SA1163
Q 118 (A,84,138) Transistor 2SC2713
MISCELLANEOUS
Q 121 (B,115,120) Chip Transistor DTA114EUA
IC 101 (A,122,132) IC TJA1040T Q 122 (B,128,122) Transistor 2SC4081
IC 105 (A,117,140) IC HA12241FP Q 123 (B,121,126) Transistor 2SC4081
IC 202 (A,104,131) IC NJM4580MD Q 124 (B,122,129) Chip Transistor 2SA1576A
IC 203 (B,130,113) IC BA4560RFV Q 181 (B,119,140) Transistor 2SC4081
IC 301 (A,41,66) IC NJM4580MD E
Q 190 (B,136,130) Transistor 2SC4081
IC 302 (A,39,73) IC NJM4580MD Q 191 (B,152,99) Chip Transistor DTA114EUA
IC 303 (A,50,66) IC NJM4580MD Q 192 (B,90,123) Transistor 2SB1198K
IC 304 (A,48,73) IC NJM4580MD Q 193 (B,90,126) Transistor 2SC2713
IC 305 (B,41,123) IC BA4560RFV Q 301 (A,49,117) Transistor DTC323TU
IC 501 (A,67,37) IC PML011A
Q 302 (A,45,117) Transistor DTC323TU
IC 502 (A,97,47) IC AK5381VT Q 303 (A,55,116) Transistor XN0F261
IC 503 (A,95,60) D/A Converter PCM1753DBQ Q 304 (A,41,108) Transistor DTC323TU
IC 504 (A,95,69) D/A Converter PCM1753DBQ Q 305 (A,44,109) Transistor DTC323TU
IC 505 (A,95,77) D/A Converter PCM1753DBQ Q 306 (A,60,111) Transistor XN0F261
IC 506 (A,86,43) IC NJM4580MD
Q 307 (B,38,145) Transistor XN0F261 F
IC 507 (A,68,57) IC NJM4580MD Q 391 (A,157,105) Chip Transistor DTC124EUA
IC 508 (A,68,72) IC NJM4580MD Q 392 (A,155,105) Chip Transistor DTC124EUA
IC 509 (A,68,83) IC BA4560RFV Q 393 (A,152,105) Chip Transistor DTA114EUA
DEX-MG3147ZH/XN/UC
7
79
5 6 8
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 401 (B,164,67) Chip Transistor 2SA1576A D 123 (A,125,144) Diode UDZS20(B)
DEX-MG3147ZH/XN/UC
7
81
5 6 8
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 301 (A,38,61) RS1/16S912J R 407 (B,166,112) RS1/16S0R0J
R 302 (A,40,62) RS1/16S274J R 408 (B,164,97) RS1/16S681J
R 303 (B,38,61) RS1/16S333J R 410 (B,166,74) RS1/16S101J
R 304 (B,41,61) RS1/16S333J R 411 (B,166,72) RS1/16S101J
A
R 305 (A,46,62) RS1/16S912J R 412 (A,179,66) RS1/16S272J
DEX-MG3147ZH/XN/UC
82
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 546 (A,90,70) RS1/16SS221J R 625 (A,143,77) RS1/16S681J
R 547 (A,100,79) RS1/16SS0R0J R 626 (A,143,75) RS1/16S681J
R 548 (A,100,78) RS1/16SS0R0J R 627 (B,148,39) RS1/16S473J
R 549 (A,100,77) RS1/16SS0R0J R 628 (B,148,47) RS1/16S473J A
R 550 (A,100,76) RS1/16SS0R0J R 629 (B,148,41) RS1/16S473J
DEX-MG3147ZH/XN/UC
7
83
5 6 8
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 696 (A,123,27) RS1/16S473J R 775 (A,23,26) RS1/4SR68J
R 697 (B,81,91) RS1/16S103J R 776 (A,23,37) RS1/4SR68J
R 698 (B,81,96) RS1/16S103J R 777 (A,23,32) RS1/4SR68J
R 699 (B,81,97) RS1/16S103J R 778 (A,149,98) RS1/16S274J
A
R 701 (A,18,99) RS1/16S223J R 779 (A,150,92) RS1/16S3002F
DEX-MG3147ZH/XN/UC
84
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C
Unit Number : CWX3473
R
R
305
306
(B,68,42)
(B,67,42)
RS1/16SS822J
RS1/16SS822J D
DEX-MG3147ZH/XN/UC
7
89
5 6 8
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 702 (A,24,22) RS1/16SS103J C 212 (A,43,41) CKSSYB104K10
R 703 (A,21,22) RS1/16SS184J
C 213 (A,38,37) CKSSYB104K10
R 704 (A,21,20) RS1/16SS223J C 214 (A,29,31) CCSSCH680J50
A
R 705 (B,32,23) RAB4CQ221J C 216 (A,50,41) CKSSYB152K50
R 706 (B,28,20) RS1/16SS221J C 217 (A,29,24) CKSSYB104K10
R 707 (A,14,15) RS1/16SS473J C 218 (A,28,21) CKSSYB102K50
R 708 (A,25,17) RS1/16SS103J
C 219 (A,51,38) CKSSYB102K50
R 709 (A,12,26) RS1/16SS103J C 220 (A,50,37) CKSSYB104K10
R 710 (B,25,17) RS1/16SS473J C 221 (B,51,24) CKSSYB104K10
R 711 (B,26,17) RS1/16SS123J C 222 (A,36,16) CKSSYB104K10
R 712 (B,28,22) RAB4CQ221J C 223 (B,62,24) CKSSYB104K10
R 713 (B,27,30) RAB4CQ221J
C 225 (A,35,14) CKSSYB104K10
R 714 (A,12,25) RS1/16SS272J C 226 (A,36,10) CKSRYB105K6R3
B R 715 (A,18,15) RS1/16SS473J C 227 (B,36,13) CKSSYB103K16
R 716 (B,19,34) RS1/16SS221J C 228 (B,67,24) CKSSYB104K10
R 717 (B,18,33) RS1/16SS221J C 230 (B,42,15) CKSSYB104K10
R 718 (B,17,33) RS1/16SS221J
C 231 (A,40,10) CKSSYB104K10
R 719 (B,17,35) RS1/16SS473J C 232 (B,69,24) CKSSYB104K10
R 720 (B,15,32) RS1/16SS102J C 233 (A,54,15) CKSSYB104K10
R 721 (A,15,15) RS1/16SS102J C 234 (A,53,8) CKSRYB105K6R3
R 723 (B,13,8) RS1/16SS473J C 235 (B,57,19) CEVW221M4
R 724 (B,14,32) RS1/16SS471J
C 237 (B,56,9) CKSSYB104K10
R 725 (B,12,8) RS1/16SS473J C 238 (A,71,5) CKSRYB474K10
R 726 (A,12,18) RS1/16SS472J C 242 (B,65,39) CKSSYB104K10
C R 729 (A,12,15) RS1/16SS0R0J C 243 (B,47,40) CKSSYB104K10
R 731 (B,9,32) RS1/16SS473J C 246 (A,72,7) 4.7 µF CCG1212
R 732 (B,10,8) RS1/16SS221J
C 301 (B,61,43) CKSSYB221K50
R 735 (A,9,25) RS1/16SS472J C 302 (B,64,42) CCSSCH151J50
R 736 (A,9,24) RS1/16SS473J C 303 (A,63,16) CKSSYB104K10
R 740 (A,7,13) RS1/16SS104J C 304 (A,60,30) CKSQYB475K10
R 742 (A,11,22) RS1/16SS103J C 305 (B,67,19) CEVW101M10
R 743 (A,21,29) RS1/16SS103J
C 306 (A,71,31) CKSSYB472K25
R 744 (A,20,30) RS1/16SS103J C 307 (A,63,31) CKSSYB103K16
R 745 (B,12,7) RS1/16SS104J C 601 (A,36,9) CKSQYB475K6R3
R 747 (A,11,28) RS1/16SS104J C 602 (A,35,12) CKSQYB475K6R3
D R 749 (A,13,30) RS1/16SS104J C 603 (A,33,10) CCSRCH102J50
R 901 (B,16,4) RS1/16SS221J
C 604 (A,33,14) CCSRCH102J50
R 902 (B,17,6) RS1/16SS221J C 701 (A,14,22) CKSRYB104K25
R 903 (A,9,12) RS1/16SS102J C 703 (B,41,20) CKSSYB103K16
R 904 (B,15,5) RS1/16SS101J C 704 (B,38,20) CKSSYB103K16
R 906 (B,20,4) RS1/16SS221J C 705 (B,41,18) CKSSYB103K16
R 909 (A,20,21) RS1/16SS473J
C 706 (B,38,18) CKSSYB103K16
R 912 (A,8,18) RS1/16SS0R0J C 709 (A,22,15) CKSRYB105K6R3
C 711 (B,20,32) CKSSYB104K10
CAPACITORS C 712 (A,19,15) CKSSYB103K16
C 713 (A,17,18) CKSQYB475K6R3
E
C 102 (B,25,36) CKSSYB104K10
C 103 (A,36,45) CKSSYB104K10 C 714 (A,14,18) CKSSYB102K50
C 104 (A,34,43) CSZS150M6R3 C 715 (A,8,20) CKSSYB104K10
C 201 (B,44,33) CKSSYB182K50 C 717 (A,15,26) CKSRYB105K6R3
C 202 (B,43,33) CKSSYB473K10 C 718 (A,23,25) CKSSYB103K16
C 719 (A,22,17) CKSSYB103K16
C 203 (A,37,38) CKSSYB104K10
C 204 (B,31,28) CKSSYB102K50 C 901 (A,15,32) CKSSYB104K10
C 205 (A,32,39) CCSSCH5R0C50 C 902 (A,27,16) CKSSYB104K10
C 206 (A,39,39) CKSSYB152K50 C 903 (B,28,10) CKSSYB104K10
C 207 (A,34,39) CCSSCH330J50 C 904 (B,72,7) CKSSYB104K10
C 905 (B,59,42) CKSSYB104K10
F C 208 (A,32,33) 0.47 µF CCG1213
C 209 (B,35,27) CKSSYB103K16 C 906 (B,8,4) CKSSYB104K10
C 210 (A,27,30) CCSSCH470J50
C 211 (A,29,28) CKSSYB682K25
DEX-MG3147ZH/XN/UC
90
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No.
D
Unit Number : CWX2986
Unit Name : RPS PCB Assy A
MISCELLANEOUS
R 14 (A,9,6) RS1/16S562J
DEX-MG3147ZH/XN/UC
7
91
5 6 8