Scribd
Upload
35 views3 pages

IAT Important Qus

The document contains important questions for the BE3251 Basic Electrical and Electronics Engineering course, divided into three parts. Part A includes definitions and principles related to electrical engineering, while Part B focuses on circuit analysis, power calculations, and the workings of various electrical machines. Part C involves determining currents in specific resistors using circuit diagrams and analysis methods.

Uploaded by

mirthikarajesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
35 views3 pages

IAT Important Qus

The document contains important questions for the BE3251 Basic Electrical and Electronics Engineering course, divided into three parts. Part A includes definitions and principles related to electrical engineering, while Part B focuses on circuit analysis, power calculations, and the workings of various electrical machines. Part C involves determining currents in specific resistors using circuit diagrams and analysis methods.

Uploaded by

mirthikarajesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

BE3251- Basic Electrical and Electronics Engineering

Important Questions -IAT 1


PART-A

1. Define RMS Value.


2. A six pole lap wound DC generator has 720 conductors a flux of 40mwb per pole is
driven at 400 rpm, find the generated emf.
3. Write down the principle of operation of transformer.
4. Define KVL, KCL
5. Define RMS and Instantaneous value.
6. List the types of DC generator
7. An electric iron rated 1000W, 240 V. Find the current drawn and resistance of the heating
element.
8. Distinguish between DC motor and DC generator
9. Write down the expression for the active power and apparent power.

PART-B
1. For the circuit shown in Figure 1(a),

Figure 1(a)
find (i) the total resistance between terminals A and B, (4)
(ii) the total current drawn from a 6V source connected from A to B, (3)
(iii) the current through 4.7 kΩ and (3)
(iv) voltage across 3, kΩ. (3)
2.
i) The voltage of v(t) = 100 sin ꞷt is applied to a circuit. The current flowing through the circuit is i(t) =
15 sin (ꞷt-30°). Determine the average power delivered to the circuit. (6)
(ii) In the parallel circuit shown in Figure 2(b), the power in the 5 Ω resistor is 600 W and the total circuit
takes 3000 VA at a leading power factor of 0.707. Find the value of impedance Z. (7)

Figure 2(b)
3.Explain with a neat circuit diagram, the construction and principle of operation of DC Generator.
4. Explain the construction and working of three phase induction motor with relevant diagram.
5.(i) Assuming necessary parameters, derive the induced E.M.F equation of a DC generator. (6)
(ii) Describe the principle of working of DC motor. (7)
6. (i) A transformer has 600 turns of the primary winding and 20 turns of the secondary winding.
Determine (1) the secondary voltage if the primary voltage is 140 V with the secondary open.
(2) the primary current if the secondary current is 90A. (7)
(ii) Compare squirrel cage and slip ring induction motors in detail. (6)
7. Determine the current in the 4Ω branch in the circuit shown in Fig. 1. Use mesh analysis method.

8. Using nodal method find current through 8Ω


resistor of Fig. 2.

Fig. 1

9. (i) A 4 pole, 1500 rpm DC generator has a lap wound armature having 24 slots with 10 conductors per
slot. If the flux per pole is 0.04 Wb, calculate the emf generated in the armature. What would be the
generated emf if the winding is wave connected? (7)

(ii) List the application of DC Generator and DC Motor. (6)


(i) Derive the EMF equation of DC Generator, considering the wave and lap winding.
(7)

1. (ii) Derive the torque equation of DC Motor. (6)


Part – C
1.Determine the current in 5Ω resistor in the circuit shown in Figure 3.

Figure 3

2. For the circuit of Fig. 3, determine v x using nodal analysis.


Figure 3

You might also like