DSC-S2000/S2100

985275011.pdf

Revision History

SERVICE MANUAL
S.M. Rev.
Ver. Date History Contents
issued
1.0 2010.01 Official Release — —

Ver. 1.0 2010.01 US Model

Canadian Model
AEP Model
Internal memory UK Model
ON BOARD
E Model
Australian Model
Chinese Model
Korea Model
Brazilian Model

Photo: DSC-S2000/Silver

SERVICE NOTE (Check the following note before the service.)

1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

1-2. REGARDING FUSE

DIGITAL STILL CAMERA

The components identified Les composants identifiés par
by mark 0 or dotted line with une marque 0 sont critiques
mark 0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
2010A2900-1
DSC-S2000/S2100 © 2010.1
9-852-750-11 Sony EMCS Co. Published by Tokai TEC
 SPECIFICATIONS
[System] [Input and Output connectors]
Image device: USB communication: Hi-Speed USB
DSC-S2100: 7.79 mm (1/2.3 type) (USB 2.0 compliant)
R, G, B primary color mosaic filters
DSC-S2000: 7.70 mm (1/2.3 type) [LCD screen]
R, G, B primary color mosaic filters LCD panel:
Total pixel number of camera: DSC-S2100: 7.5 cm (3.0 type)
DSC-S2100: Approx. 12.4 Megapixels DSC-S2000: 6.2 cm (2.5 type)
DSC-S2000: Approx. 10.3 Megapixels TFT drive
Effective pixel number of camera: Total number of dots: 230 400 (960 × 240) dots
DSC-S2100: Approx. 12.1 Megapixels
DSC-S2000: Approx. 10.1 Megapixels
Lens: 3× zoom lens [Power, general]
f = 6.2 mm – 18.6 mm (35 mm – 105 mm Power: LR6 (size AA) Alkaline batteries (2), 3 V
(35 mm film equivalent)) HR15/51: HR6 (size AA) NickelMetal
F3.1 (W) – F5.6 (T) Hydride batteries (2) (sold separately), 2.4 V
Exposure control: Automatic exposure,
ZR6 (size AA) Oxy Nickel Primary Battery (2)
Scene Selection (8 modes)
(sold separately), 3 V
White balance: Automatic, Daylight, Cloudy,
Power consumption (during shooting): 1.0 W
Fluorescent 1/2/3, Incandescent, Flash Operating temperature: 0°C to 40°C (32°F to 104°F)
Recording interval for Burst mode:
Storage temperature: – 20°C to + 60°C (– 4°F to + 140°F)
Approx. 1 second
Dimensions: 97.6 × 61.0 × 27.2 mm
File format:
(3 7/8 × 2 1/2 × 1 1/8 inches)
Still images: JPEG (W/H/D, excluding protrusions)
(DCF Ver. 2.0, Exif Ver. 2.21, MPF Baseline) Mass:
compliant, DPOF compatible DSC-S2100: Approx. 184 g (6.5 oz)
Movies: AVI (Motion JPEG) DSC-S2000: Approx. 173 g (6.1 oz)
Recording media: Internal Memory (including two batteries and memory card)
(approx. 6 MB), “Memory Stick Duo” media,
Microphone: Monaural
SD memory card, SDHC memory card
Buzzer
(Class 4, 6, 10)
Exif Print: Compatible
Flash: Flash range (ISO sensitivity
PRINT Image Matching III: Compatible
(Recommended exposure Index) set to Auto): PictBridge: Compatible
Approx. 0.5 m to 3.3 m
(1 feet 7 3/4 inches to 10 feet 10 inches) Design and specifications are subject to
(W)/ change without notice.
approx. 0.5 m to 1.8 m
(1 feet 7 3/4 inches to 5 feet 10 7/8 inches)
(T)

DSC-S2000/S2100
–2–
Model information table

Model DSC-S2000 DSC-S2100

US, CND, AEP, UK, E, US, CND, AEP, UK, E,
Destination
AUS, KR, BR AUS, CH, KR, BR

• Abbreviation
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
KR : Korea model

DSC-S2000/S2100
–3–
 SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SONY. SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes and Boards requiring use of unleaded solder are printed with the leadfree
bridges. mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are “pinched” (Caution: Some printed circuit boards may not come printed with the
or contact high-wattage resistors. lead free mark due to their particular size.)
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement. : LEAD FREE MARK
4. Look for parts which, through functioning, show obvious signs of Unleaded solder has the following characteristics.
deterioration. Point them out to the customer and recommend their • Unleaded solder melts at a temperature about 40°C higher than ordi-
replacement. nary solder.
5. Check the B+ voltage to see it is at the values specified. Ordinary soldering irons can be used but the iron tip has to be applied
6. Flexible Circuit Board Repairing to the solder joint for a slightly longer time.
• Keep the temperature of the soldering iron around 270°C during Soldering irons using a temperature regulator should be set to about
repairing. 350°C.
• Do not touch the soldering iron on the same conductor of the circuit Caution: The printed pattern (copper foil) may peel away if the heated
board (within 3 times). tip is applied for too long, so be careful!
• Be careful not to apply force on the conductor when soldering or • Strong viscosity
unsoldering. Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such as
on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also be
added to ordinary solder.
DSC-S2000/S2100
–4–
 1. SERVICE NOTE

1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY 1-2. REGARDING FUSE

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) • MAIN BOARD
Note1: When replacing main board, erase the data in internal memory of the board before replacement. Ref.NO: F1
Note2: When replacing main board, execute formatting and initialize the internal memory after replacement.
Part NO: 1-576-363-11
Description: FUSE, MICRO (1005 TYPE) (1A/30V)
Method for Copying the Data in Internal Memory
Ref.NO: F2
Copy Part NO: 1-576-913-31
Description: FUSE, MICRO (1608 TYPE) (1.6A/36V)
Copies all images in the internal memory to a memory card.

1 Insert a memory card with sufficient free capacity into the camera.
2 MENU t (Settings) t (Memory Card Tool) t [Copy] t [OK]
t z on the control button
Notes
• Use the batteries with enough power remaining. If you attempt to copy image files using batteries with
little remaining charge, the batteries may run out, causing copying to fail or possibly corrupting the data.
• Images cannot be copied individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the memory card after copying, then format the internal memory ([Format] in
[Internal Memory Tool]).
• A new folder is created on the memory card and all the data will be copied to it. Yo u cannot choose a
specific folder and copy images to it.

Method for Formatting the Internal Memory

Format
Formats the memory card or the internal memory. To ensure stable operations of the memory
card, we recommend that you use this camera to format any memory card being used with this
camera for the first time. Note that formatting will erase all data recorded on the memory card.
This data cannot be restored. Be sure to back-up any important data to a PC or other storage
location.

1 MENU t (Settings) t (Memory Card Tool) or (Internal

Memory Tool) t [Format] t [OK] t z on the control button
Note
• Note that formatting permanently erases all data including even protected images.

DSC-S2000/S2100
1-1E
 2. REPAIR PARTS LIST

IDENTIFYING PARTS
(ENGLISH)
Follow the disassembly in the numerical order given. NOTE:
When indicating parts by reference
• -XX, -X mean standardized parts, so they may have some differences from the original one.
number,please include the board name.
• Items marked “*” are not stocked since they are seldom required for routine service. Some
delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied. The components identified by mark 0 or
• Due to standardization, replacements in the parts list may be different from the parts speci- dotted line with mark are critical for safety.
fied in the diagrams or the components used on the set. Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.

• Color Indication of Appearance Parts

6 TOP Cover Assy
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color

• Abbreviation View Position

AUS : Australian model
8 Stroboscope Block Assy BR : Brazilian model Top View
CH : Chinese model
CND : Canadian model
KR : Korea model Left View
Back View
9 SW Board

1 Cabinet (Rear) Assy

Front View Right View

5 LCD Module
3 DC Door Bottom View

THE COMBINATION OF CABINET’S COLOR AND SCREW (S2000) THE COMBINATION OF CABINET’S COLOR AND SCREW (S2100)
4 LCD Bracket The screw pointed is different according to the cabinet's color. The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table For the combination of cabinet's color and screw, please refer to Table
2-1. 2-2.
0 Main Board

qa Lens Block Assy

qs Main Frame Sub Assy

2 Cabinet (Front) Assy

Table 2-1 Table 2-2

Screw's Screw's
Cabinet's Color Cabinet's Color
Ref. No. (Parts Color.) Ref. No. (Parts Color.)
#S2 (Silver) SILVER #S2 (Silver) SILVER, ORANGE
#S4 (Black) BLACK #S4 (Black) BLACK

Link DISCHARGING OF THE CHARGING CAPACITOR ACCESSORIES

ACCESSORIES ASSEMBLY

DSC-S2000/S2100
2-1
 NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of Cut and remove the part of gilt
bent at the terminal. which comes off at the point.
Do not insert the cable insufficiently nor crookedly. (Be careful or some
pieces of gilt may be left inside)
• When remove a connector, don’t pull at wire of connector. It is pos-
sible that a wire is snapped.

• When installing a connector, don’t press down at wire of connector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

DISCHARGING OF THE CHARGING CAPACITOR

The charging capacitor is charged up to the maximum 315 V
Note: High-voltage cautions
potential.
There is a danger of electric shock by this high voltage when the Discharging the Capacitor
capacitor is handled by hand. The electric shock is caused by the Short-circuit between the two points with the
charged voltage which is kept without discharging when the main short jig about 10 seconds.
power of the unit is simply turned off. Therefore, the remaining To avoid the spark with the metal plate,
voltage must be discharged as described below. wrap the short jig with the insulation tape.

R:1 k /1 W
Preparing the Short Jig (Part code: 1-215-869-11)
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to Protection
prevent electrical shock. Sheet
Remove

Stroboscope
Block Assy

Wrap insulating tape.

DSC-S2000/S2100
2-2
2-1. EXPLODED VIEWS DISASSEMBLY
#S2 1(Claw)
#S4
2-1-1. OVERALL SECTION (Note1) 1. Remove to numerical order (1 to 5) in the left figure.
1�5
1 #S2 / #S4 X 7
#S2
Left View Right View Bottom View
5�4 #S4
DSC-S2000 (Note1)

Main Frame Section #S2

(See Page 2-4) #S4
4 #S2 #S2
#S5 (Note1)
#S4 #S4 #S2
#S4
#S3
2 BT Lid Open (2) → #S3 X 1

Bottom View
3�2
2(Claw) 4�3 #S3
1(Claw)
#S2
#S4
2
(Note2) 1�5
S2000 4 LCD Module Raise ( 4) → #S3 X 3 → #S5 X 1

2�1 5�4 Back View

#S5
#S3

4
4�3 #S2
#S3
#S4 S2100 4 LCD Module Raise (4) → #S3 X 3
(Note2)
#S3
Back View
3�2
2(Claw)

DSC-S2100

2 #S3
Main Frame Section
(See Page 2-4)
#S3
2�1
#S2
#S4
Note
(Note2)
Note1: Please refer to “THE COMBINATION OF CABINET’S COLOR Note2: Please refer to “THE COMBINATION OF CABINET’S COLOR
AND SCREW (S2000)” on page 2-1 about the combination AND SCREW (S2100)” on page 2-1 about the combination
Ref. No. Part No. Description Ref. No. Part No. Description cabinet’s color and screw. cabinet’s color and screw.
1 X-2546-381-1 CABINET (FRONT) ASSY (S) (S2000:SILVER) 4 1-811-106-11 LCD MODULE (S2100)
1 X-2546-382-1 CABINET (FRONT) ASSY (B) (S2000:BLACK) 4 1-811-107-11 LCD MODULE (S2000)
1 X-2546-383-1 CABINET (FRONT) ASSY (S) (S2100:SILVER) 5 X-2546-386-1 CABINET (REAR) ASSY (S) (S2000:SILVER)
1 X-2546-384-1 CABINET (FRONT) ASSY (O) (S2100:ORANGE)
1 X-2546-385-1 CABINET (FRONT) ASSY (B) (S2100:BLACK) 5 X-2546-387-1 CABINET (REAR) ASSY (B) (S2000:BLACK)
5 X-2546-388-1 CABINET (REAR) ASSY (S) (S2100:SILVER)
2 4-173-837-01 DOOR (S), DC (S2000:SILVER) 5 X-2546-389-1 CABINET (REAR) ASSY (O) (S2100:ORANGE)
2 4-173-838-01 DOOR (B), DC (S2000:BLACK) 5 X-2546-390-1 CABINET (REAR) ASSY (B) (S2100:BLACK)
2 4-173-839-01 DOOR (S), DC (S2100:SILVER)
2 4-173-840-01 DOOR (O), DC (S2100:ORANGE) #S2 3-287-027-01 SCREW_TP_1.7_4_A_0.3_ (Note1, 2)
2 4-173-844-01 DOOR (B), DC (S2100:BLACK) #S3 4-137-871-01 SCREW_TP_1.4_3.5_A0.3_D2.5_N
#S4 4-174-629-01 SCREW_TP_1.7_4_A_0.3_BLK (Note1, 2)
3 4-173-835-01 BRACKET, LCD (S2000) #S5 3-113-001-01 SCREW TP 1.4*2.5
3 4-173-836-01 BRACKET, LCD (S2100)
DSC-S2000/S2100
2-3
2-1-2. MAIN FRAME SECTION
DISASSEMBLY
ns: not supplied
1. Remove to numerical order (6 to 0) in the left figure.

6 #S5 X 4

Front View Top View Back View

#S5

#S5

#S5
#S5
DSC-S2000
6 52 9
#S5
9�54 ns 7 Protection Sheet Remove 8 #S1 X 2

#S5 Right View Top View

DISCHARGING OF THE CHARGING CAPACITOR
ns #S3 DSC-S2100 #S1 #S1
#S1 53 B
7 ns
9�54
8�51 9
#S3 ns

ns
53
B 9 / 0 Black Mylar Remove (9) → #S3 X 4
#S1
#S3 Back View

A
#S3
B
ns
A

F1 56
F2 Note
Solder
Note: Refer to “Assembly-1” when you assemble Routing harness
Solder 0�55 of Main Frame Sub Assy.
57 (Note)

Lens Section
(See Page 2-5)

Ref. No. Part No. Description Ref. No. Part No. Description
51 A-1759-672-A STROBOSCOPE BLOCK ASSY * 56 1-820-333-11 MULTI CONNECTOR (REC) 8P
52 X-2546-391-1 COVER ASSY, TOP (S2000) 57 1-858-372-11 BUZZER, PIEZOELECTRIC
52 X-2546-392-1 COVER ASSY, TOP (S2100)
53 1-822-837-21 CARD CONNECTOR 0 F1 1-576-363-11 FUSE, MICRO (1005 TYPE) (1A/30V)
54 A-1759-673-A SW BOARD, COMPLETE (S2100) 0 F2 1-576-913-31 FUSE, MICRO (1608 TYPE) (1.6A/36V)

54 A-1760-418-A SW BOARD, COMPLETE (S2000) #S1 3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5

55 A-1759-674-A MAIN BOARD, COMPLETE (S2000) (Note) #S3 4-137-871-01 SCREW_TP_1.4_3.5_A0.3_D2.5_N
55 A-1759-675-A MAIN BOARD, COMPLETE (S2100) (Note) #S5 3-113-001-01 SCREW TP 1.4*2.5

DSC-S2000/S2100
2-4
2-1-3. LENS SECTION
DISASSEMBLY
ns: not supplied
1. Remove to numerical order (qa to qs) in the left figure.

qa #S3 X 3

Back View

#S3

105
Note
(CCD Assy)
104 (Note) Note: Be careful about the Lens Block Assy.

103 Don't press the Barrier part

ns
ns #S1
qa�102 (Note)

Be careful of the Weld

qs�101
#S3

Don't press
Don't press the
the AF motor
Sensor holder

Keep clean
Be careful of the weld
these Pins

Ref. No. Part No. Description Ref. No. Part No. Description
101 X-2546-393-1 FRAME SUB ASSY (S), MAIN (S2000:SILVER) 104 A-1759-685-A CCD BLOCK ASSY (S2000) (Note)
101 X-2546-394-1 FRAME SUB ASSY (B), MAIN (S2000:BLACK) 104 A-1759-686-A CCD BLOCK ASSY (S2100) (Note)
101 X-2546-395-1 FRAME SUB ASSY (S), MAIN (S2100:SILVER) 105 4-173-845-01 SHEET, CCD MYLAR
101 X-2546-396-1 FRAME SUB ASSY (O), MAIN (S2100:ORANGE)
101 X-2546-397-1 FRAME SUB ASSY (B), MAIN (S2100:BLACK) #S1 3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5
#S3 4-137-871-01 SCREW_TP_1.4_3.5_A0.3_D2.5_N
102 A-1759-676-A LENS BLOCK ASSY (Note)
103 4-151-712-01 FILTER ASSY, LOW PASS

DSC-S2000/S2100
2-5
 3. ASSEMBLY

Assembly-1: Routing harness of Main Frame Sub Assy

Checking supplied accessories.
DSC-S2000 BATT-1 BATT+1
Note: This item is supplied with the unit as an accessory,
but is not prepared as a service part.

LR6 (size AA) alkaline batteries

(Note)

Instruction Manual
(Only for destination Japanese model)

4-170-175-11 (SIMPLIFIED CHINESE)

4-170-176-11 (ENGLISH) Main Board Main Frame Sub Assy
∗ 4-170-176-21 (ENGLISH,SPANISH)
∗ 4-170-176-31 (ENGLISH,FRENCH)
∗ 4-170-176-41 (ENGLISH,RUSSIAN,UKRAINIAN)
Dedicated USB cable ∗ 4-170-176-51 (ENGLISH,FRENCH,ITALIAN,SPANISH,PORTUGUESE, DSC-S2100 BATT-1 BATT+1
1-834-311-51 GERMAN,DUTCH,TURKISH,GREEK,POLISH,CZECH,
HUNGARIAN,SLOVAK,SWEDISH,FINNISH,NORWEGIAN,
DANISH,CROATIAN,ROMANIAN)
∗ 4-170-176-61 (ENGLISH,TRADITIONAL CHINESE,SIMPLIFIED CHINESE,
MALAY,INDONESIAN,THAI,ARABIC,PERSIAN)
∗ 4-170-176-71 (ENGLISH,SPANISH,PORTUGUESE)
∗ 4-170-176-81 (ENGLISH,TRADITIONAL CHINESE,SIMPLIFIED CHINESE,
INDONESIAN,ARABIC,PERSIAN)
4-170-177-21 (KOREAN)

Wrist strap
2-050-981-01

Main Board Main Frame Sub Assy

Cyber-shot Handbook (PDF)

The CD-ROM supplied contains all of language version of
the Cyber-shot Handbook (PDF) for printing.
The printed matter is not supplied. If required, please
order it with the part number below.
(Only for destination Japanese model)

∗ 4-166-207-11 (ENGLISH) ∗ 4-166-208-71 (HUNGARIAN)

CD-ROM ∗ 4-166-207-21 (FRENCH) ∗ 4-166-208-81 (SLOVAK)
- Cyber-shot application software ∗ 4-166-207-31 (ITALIAN) ∗ 4-166-208-91 (SWEDISH)
- “Cyber-shot Handbook” ∗ 4-166-207-41 (SPANISH) ∗ 4-166-209-11 (FINNISH)
4-174-171-01 ∗ 4-166-207-51 (PORTUGUESE) ∗ 4-166-209-21 (NORWEGIAN)
∗ 4-166-207-61 (GERMAN) ∗ 4-166-209-31 (DANISH)
∗ 4-166-207-71 (DUTCH) ∗ 4-166-209-41 (THAI)
∗ 4-166-207-81 (TRADITIONAL CHINESE) ∗ 4-166-209-51 (MALAY)
∗ 4-166-207-91 (SIMPLIFIED CHINESE) ∗ 4-166-209-61 (TURKISH)
∗ 4-166-208-11 (RUSSIAN) ∗ 4-166-209-71 (GREEK)
∗ 4-166-208-21 (ARABIC) ∗ 4-166-209-81 (UKRAINIAN)
∗ 4-166-208-31 (PERSIAN) ∗ 4-166-209-91 (CROATIAN)
∗ 4-166-208-41 (KOREAN) ∗ 4-166-210-11 (ROMANIAN)
∗ 4-166-208-51 (POLISH) ∗ 4-166-210-21 (INDONESIAN)
∗ 4-166-208-61 (CZECH)

DSC-S2000/S2100
3-1E
 4. BLOCK DIAGRAM

4-1. OVERALL BLOCK DIAGRAM

LENS DSP MEMORY

+3.1VD MD_EXT MEM_CK +3.1VD

+3.1VD MD_EXT MD_SEN MD_EXT MEM_CK MEM_CKN MEM_CK +3.1VD
+4.8VD MD_SEN MD_SCK MD_SEN MEM_CKN MEM_CS MEM_CKN +1.8VD
+4.8VD MD_SCK MD_SCK MEM_CS MEM_CS +1.8VD
LENS Module DGND MD_SDA
MD_SDA
MD_IN1 MD_SDA MEM_RAS
MEM_RAS
MEM_CAS MEM_RAS DGND
DGND MD_IN1 MD_IN2 MD_IN1 MEM_CAS MEM_WE MEM_CAS DGND
MD_IN2 MD_IN3 MD_IN2 MEM_WE MEM_CKE MEM_WE
MD_IN3 MD_IN4 MD_IN3 MEM_CKE MEM_LDM MEM_CKE
MD_IN4 FOCUS_PI MD_IN4 MEM_LDM MEM_UDM MEM_LDM
FOCUS_PI ZOOM_PI FOCUS_PI MEM_UDM MEM_LDQS MEM_UDM
ZOOM_PI ZOOM_PR ZOOM_PI MEM_LDQS MEM_UDQS MEM_LDQS
ZOOM_PR PS4_CLK ZOOM_PR MEM_UDQS MEM_BA0 MEM_UDQS
PS4_CLK PS4_CLK MEM_BA0 MEM_BA0
MD_MOB MEM_BA1
MEM_BA1
MEM_A[0..12] MEM_BA1 MEMORY
MD_MOB MD_MOB MEM_A[0..12] MEM_D[0..15] MEM_A[0..12]
LENS MEM_D[0..15] MEM_D[0..15]
MFDD[0..7]
MFD[0..7] MFD_WP MFD[0..7]
MFD_WP MFD_WE MFD_WP
JACK_AUDIO MFD_WE MFD_ALE MFD_WE
MFD_ALE MFD_RDY MFD_ALE
+3.1VD USB_DET MFD_RDY MFD_RE MFD_RDY
+3.1VD USB_DET USB_D+ USB_DET MFD_RE MFD_CE MFD_RE
+14V USB_D+ USB_D- USB_D+ MFD_CE MFD_CLE MFD_CE
+14V USB_D- USB_D- MFD_CLE MFD_CLE
DGND A/V_DET
DGND A/V_DET A/V_DET
USB JACK
VIDEO_OUT MEMORY
VIDEO_OUT VIDEO_OUT
TOP_SW_MS
+3.1V_AFE PA2
+3.1V_AFE PA2 PA0 PA2
PA0 PA1 PA0
PA1 PD6 PA1 +3.3VS
PD6 PB[0..7] PD6 +3.3VS
MICP PB[0..7] SW1_CTRL PB[0..7] +3.1VD
MICP MICN MICP SW1_CTRL STA_LED SW1_CTRL +3.1VD
MICN MICN STA_LED STA_LED PVM
BUZZER KEY_PWR PVM
BUZZER BUZZER KEY_PWR KEY_PB KEY_PWR FLASH_VP
KEY_PB KEY_PB FLASH_VP
MD1
MD1
MD1 KEY_SHUT1
KEY_SHUT1
KEY_SHUT2 KEY_SHUT1 DGND memory stick
KEY_SHUT2 KEY_SHUT2 DGND
JACK_AUDIO KEY_TELE
KEY_TELE
KEY_WIDE KEY_TELE Module
KEY_WIDE KEY_MODE KEY_WIDE
KEY_MODE KEY_SW KEY_MODE
KEY_SW PWR_LED KEY_SW
PWR_LED PWR_LED
STROBE_CHG
VP STROBE_CHG CHARGE_DONE STROBE_CHG
+3.1V_AFE VP CHARGE_DONE STROBE_TRG CHARGE_DONE
+3.3VS +3.1V_AFE STROBE_TRG SELF_LED STROBE_TRG
+3.1VD +3.3VS SELF_LED SELF_LED
+1.8VD +3.1VD TOP_SW_MS
+1.2VD +1.8VD
DGND +1.2VD CDS
DGND
CCD[0..11] +1.8VD
CCD[0..11] PXCLK CCD[0..11] +1.8VD
PXCLK CCD_HD PXCLK +3.1V_AFE
CCD_HD CCD_VD CCD_HD +3.1V_AFE
CCD_VD AFE_RST CCD_VD +13V
AFE_RST AFE_RST +13V
POWER
AFE_SEN
AFE_SEN
AFE_SDA AFE_SEN -7.5V
CCD sensor
VP AFE_SDA AFE_SCK AFE_SDA -7.5V
FLASH_VP VP PWR_CTRL AFE_SCK AFE_SCK DGND
FLASH_VP PWR_CTRL PWR_CTRL DGND +3.1V_AFE2
+3.3VS CCD_ON +3.1V_AFE2
+3.3VS CCD_ON CCD_ON CDS
+4.8VD
PVM +4.8VD
+3.1VD PVM BAT_CHK LCD
+3.1V_AFE +3.1VD BAT_CHK BAT_AD BAT_CHK
+1.2VD +3.1V_AFE BAT_AD BAT_AD LCD_VD +3.1VD
+1.2VD LCD_VD LCD_VD +3.1VD
BATT

+1.8VD LCD_HD
+1.8VD LCD_HD LCD_MCLK LCD_HD
+14V BL_ON LCD_MCLK LCD[0..7] LCD_MCLK
+13V +14V BL_ON BL_ON LCD[0..7] LCD_SEN LCD[0..7] DGND
+13V
LED+
LED+ LCD_SEN
LCD_SCK
LCD_SCK LCD_SEN
LCD_SCK
DGND LCD
-7.5V LED- LCD_SDA LED+
-7.5V LED- LCD_SDA LCD_SDA LED+ LED-
DGND LED-
DGND +3.1V_AFE2
LCD
POWER DSP

DSC-S2000/S2100
4-1E