Delta Servo Press - E Series

Installation and Maintenance

Instructions

www.deltaww.com
Safety Notice
This manual includes safety precautions on user safety and how to prevent the servo press
from getting damaged, warnings and notes are used in this manual to describe how important
these safety precautions are. Warnings are used to describe supplementary explanations, users
must read the items in the warning, danger and stop carefully in order to prevent accidents or
causing injuries to the staff.
The installation and transportation of the servo press should be executed by qualified
personnel and should comply with the regional / country and local laws and regulation
requirements.
The servo press is partly-completed machine accordance with Machinery Directive
(2006/42/EC)pressing, the safeguards and related circuits are responsible by the final system
integrator.
This servo press was designed only as an accessory for specific applications. We strongly
suggest that this servo press should not be modified and/or used for any application processes
other than what it was designed for. If you have any application problems, please do not use the
servo press until you have received detailed explanations from your dealer.
The purpose of these introductions is to advise the customer and the operator on the
design, construction, operation and maintenance of Servo Press. The attached illustrations,
drawings and diagrams are intended to show the outstanding features, but are not binding for
dimensional accuracy or further details. It provides extremely high machining accuracy. Be careful
the properties of processing material, e.g. pressing, trimming or assemble of cold-metal, sheet or
other likes, etc.
It is forbidden to process flammable, toxic or explosion materials.
Definition of operators
The definition of servo press operators is as follows.
Operator
‧ Able to perform operations such as powering the controller ON/OFF.
‧ Able to start the servo press from the final system integrated operation panel.
Program editor
‧ Performs the operations on the servo press.
‧ Uses manual mode to operate the servo press or teach points, etc. outside the safety fence.
Repair or inspection personnel
‧ Perform simple operations of the servo press.
‧ Uses manual mode to operate the servo press outside the safety fence.
‧ Performs operations such as maintenance, repairs, adjustment and replacement, etc. to the
servo press and controller

FIRST RUN,
Product conforms to the Machinery Directive 2006/42/EC, Low Voltage Directive 2014/35/EU,
EMC Directive 2014/30/EU and related standards EN ISO 12100, EN ISO 16092-1, EN ISO 16092-2,
EN ISO 13857, EN 60204-1, EN 61000-6-2, EN 61000-6- 4, EN 61000-3-2, EN 61000-3-3.

Note: Please read the manual carefully before operating, maintaining or inspecting the servo press
and controller, and make sure to follow the safety regulations. Please contact our company for
details if you have any questions.

5
Definitions of stop, Danger and Warning
For your safety, please read this manual before using the servo press and have a clear
understanding of all contents related to safety and warnings.
Servo press operators must receive training, read and understand how to use the safety measures,
also to follow and execute all the rules described in this manual.

Meanings of the symbols “Danger”, “Warning” and “Prohibited”.

Means that danger is about to happen and may result in fatalities or severe injuries
to the staff, if not prevented.

Means that there is potential danger and may result in fatalities or severe injuries to
the staff, if not prevented.

Refers to activities that are absolutely prohibited; failure to comply may result in
damage or malfunctions to the product causing the product to be unusable or it may
result in injuries to the staff.

There is excessive noise that may affect the hearing when the servo press is
operating; operators should wear earmuffs if feeling any discomfort.

6
Installation safety
◼ Please read this manual carefully before installing in order to make sure that
the servo press and controller are installed at suitable usage locations and
environments, to avoid affecting the mechanisms and usage life of the
electronic components or encountering other safety problems.
◼ Please do not modify the machine or wiring by yourself or use with other
controllers or servo press. Our company will not be held responsible for any
injuries or fatalities caused by accidents that result from doing so.
◼ Please follow the instructions in this manual properly to transport and install
the servo press and controller correctly; otherwise it might result in damage to
the servo press or controller.
◼ Related licenses are required to operate stackers or fork lifts etc.
◼ Please wear proper safety work clothes, helmets, gloves and shoes when
installing the servo press and controller in order to ensure the safety of
personnel.
◼ Do not add additional cables or hoses etc. inside the servo press. When
installing the exterior cables of the servo press, make sure to assess whether
the cables and mechanisms will interfere with one another during operations.
◼ The servo press itself is applicable for environment IP20 and is able to resist
solid matters with diameters over 12mm and lengths not exceeding 80mm,
such as fingers; it is not protected against any liquid matter.
◼ Please follow the manual to install the safety protection devices such as fence,
light curtain etc. in order to prevent injuries or other dangers caused to the
staff arising from impact by the servo press within the operating range of the
servo press.
◼ Please install the final system integration of the user operating buttons and
warning lights etc. outside the fence in order to ensure usage safety. The height
of the operating interface should be a suitable (0.6m to 1.7m) range for
operators to touch.
◼ Please do not turn the power on and off frequently as doing so may result in
damage to the controller.
◼ The servo press system should be installed under the specified conditions; in
the foreseeable usage period, the servo press cannot be tilted or moved with
uncontrolled methods during transportation, assembly, dis-assembly,
suspended or discarded periods.
◼ Please properly ground all servo press systems; they should all be grounded
before connecting the power.
◼ The final system integrator should install protection devices in order to prevent
users from getting close to the danger area.
◼ Do not bypass the interlock circuit.
◼ Removing or changing the locations of any safety warning labels is strictly
prohibited as doing so may cause danger to the staff and to cause injuries.
◼ Performing any unsafe actions at the safety warning locations is strictly
prohibited as doing so may cause injuries to the staff.
◼ Personnel must not stand beneath when stackers or fork lifts, etc. are used to
move the servo press as doing so may result in injuries or other dangers.

7
◼ Stacking objects on top of the servo press, controller or cables is strictly
prohibited as doing so may cause damage to the servo press, controller or
cables.
◼ Changing or modifying the servo press and controller is strictly prohibited as
doing so may result in damages to the servo press or controller and danger to
the staff. Our company will not be held responsible for any work accidents.
◼ Installing and wiring of the servo press by people without related professional
knowledge or licenses is strictly prohibited.

8
Usage and operating safety
◼ Please read this manual carefully before usage in order to ensure proper usage
and the safety of the maintenance staff.
◼ Due to operational environment and operator safety considerations, our
company will provide dedicated training for the operators of different servo
press applications in order to ensure usage safety. Please contact our company
or your local dealers if training is needed.
◼ Please perform wiring properly according to this manual; wiring must be
performed by personnel with related professional knowledge or licenses.
◼ Cannot be used on production lines that are flammable, explosive, toxic or has
the risk of being sprayed by liquids.
◼ Please select a suitable model according to the load capability; do not overuse
specifications that exceed the machine model specifications.
◼ The servo press is a partially completed machine; the assembly and
construction of the protection and safety circuit should be the responsibility of
the final system integrator.
◼ All children and visitors should keep a safe distance from the processing area.
◼ Do not wear loose clothes, ties, rings or bracelets and wear protective nets to
protect long hair as these things can easily get caught in the machine by
accident and cause injuries to the staff or cause other dangers during
operation.
◼ Please turn off the power, isolate the power properly and wait for the servo
press to stop completely when the servo press is no longer used before you
leave.
◼ Please confirm that there is no one along the fence before operating the servo
press and performing operations.
◼ Do not laugh or talk to other workers while operating the servo press; such
wrong behaviors may result in collision of the servo press or injuries to other
workers.
◼ Please have the senior supervisor keep the internal/external mode selection
switch key; do not place it randomly or leave it inserted on the selection switch
as doing so may result in other personnel activating the servo press
accidentally, causing injuries to the workers.
◼ Please use slow speed operations when operating the servo press manually for
the first time, otherwise being unfamiliar with the operations may result in
damage to the servo press due to impact or cause injuries to other workers.
◼ Please do not turn the power on and off frequently as doing so may result in
damage to the controller.
◼ Improper operations might damage the servo press.
◼ When collisions happen to the servo press, please turn off the power of the
servo press first and then check the components and cables of the servo press
to make sure they were not damaged before turning the power back on to
perform operations again.
◼ Please use a safety lock on the fence switch when entering the fence to operate
the servo press in order to prevent the fence from closing suddenly causing the
servo press to be activated accidentally.

9
◼ The location of the interlock switch between the structure of the safety
protection device and the protection device should comply with EN ISO 14120
and EN ISO 14119 standards, and the safety distance should be designed
according to EN ISO 13857 standards.
◼ Do not operate the press when light curtain, safety guard, or safeguards are
not provided.
◼ Do not operate the press under out of limit.
◼ Short-circuiting of any safety protection signals on the controller is strictly
prohibited, otherwise our company will not be held responsible for any work
accidents that may occur.
◼ When operating the servo press all personnel are prohibited from standing
close or within the servo press working range; doing so will cause injuries to the
other workers.
◼ Do not unplug any cables on the controller while the servo press is operating;
doing so will cause damage to the controller.
◼ Do not open the protective cover or protection device while the machine and
servo press are operating.

10
Maintenance safety
◼ Please perform maintenance and inspection work properly according to the
manual in order to prolong the usage life of the servo press.
◼ Please add a safety lock on the power switch of the power box when
performing maintenance or repair operations on the servo press, and place a
“Do not power on” safety warning at an obvious place.
◼ Make sure foreign objects do not get attached or enter the servo press when
performing maintenance or inspection.
◼ Making random oil changes during maintenance may result in damaging the
performance of the servo press or to the mechanical components.
◼ Protection devices and repair doors in the danger areas that need to be opened
or removed regularly for the purpose of operations, maintenance, cleaning and
configuration should be interlocking.
◼ Personnel performing maintenance or repairs on the servo press or servo press
system should receive the necessary process training in order to execute the
tasks required. Also use only genuine materials, or else it might cause grave
danger to the users.
◼ The processing of waste materials should comply with local laws and
regulations, and should be treated carefully.
◼ Random changes to the maintenance schedule of the servo press and
maintenance oil are strictly prohibited.
◼ Maintenance and inspection to the controller and servo press are prohibited
while power is being supplied or else it may cause electrical shocks or injuries
to the workers.
◼ When a servo press component is damaged, replacing with other brand
components is prohibited as doing so many result in damaging the
performance of the servo press or the components.
◼ When internal components of the controller are damaged, replacing them with
other brand components is prohibited; doing so may cause accidents or result
in decreasing the safety performance levels.
◼ The power control box must not be opened within 10 minutes of powering off
because the residual voltage in the driver may cause electrical shocks.

11
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

Contents Delta Electronics Servo Press

(External Electric Cylinder)
Installation and Maintenance
Instructions

1. Safety Information............................................................... 2
1.1 Safety Information Before Use ........................................................................... 2
1.2 Safety Information During Use ........................................................................... 3
1.3 Safety Information During Maintenance and Under Other Circumstances ......... 3
1.4 Powering System ............................................................................................... 3

2. Comprehensive System Structure .................................... 4

2.1 Model & Electronic Control Panel ...................................................................... 4

3. Installation Setup ................................................................ 5

3.1 Fixed Way .......................................................................................................... 5
3.1.1 AM-ESP-E050-XXXX/AM-ESP-E030-XXXX models ............................. 5
3.1.2 AM-ESP-E010-XXXX / AM-ESP-E005-XXXX models ........................... 6
3.1.3 AM-ESP-E002-XXXX / AM-ESP-E001-XXXX models ........................... 7
3.2 Loading and Unloading Spindle Punch .............................................................. 8
3.2.1 AM-ESP-E050-XXXX / AM-ESP-E030-XXXX models .......................... 8
3.2.2 AM-ESP-E010-XXXX / AM-ESP-E005-XXXX models ........................... 9
3.2.3 AM-ESP-E002-XXXX / AM-ESP-E001-XXXX models ......................... 10
3.2.4 Restrictions of Jig ............................................................................... 11

4. Equipment Care and Maintenance .................................. 12

4.1 Applying Oil to Equipment ................................................................................ 12
4.2 Load Cell Calibration ........................................................................................ 14

5. Wiring Instructions ........................................................... 15

5.1 Circuit Diagram ................................................................................................ 15
5.2 Detailed Explanation of PLC External I/O Points ........................................... 16
5.3 Wiring Instructions ........................................................................................... 17
5.4 Wire Table and Wire Size for Wiring ................................................................ 18
5.5 Details of Drive Power Distribution ................................................................... 19
5.5.1 0.4 kW~1 kW ........................................................................................ 19
5.5.2 2 kW~7.5 kW ........................................................................................ 20
5.6 External Button ................................................................................................ 21

1
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

1. Safety Information
1.1 Safety Information Before Use
Item Description

Please shut down power before removing the external power lines to
the unit so that the unit is in a disconnected state when the servo press
will be out of service for an extended period of time.

Please follow the main power and voltage requirements.

Power Supply
Do not let the servo press or power lines get exposed to water or oil.

Make sure that the power line is properly plugged and fastened.

For long-term use, please periodically check if the screws fixating

the unit are loose and re-fasten loose ones.

While in operation, warning signs may be put up in the surroundings

to prevent against possible danger.

Do not modify or alter the equipment yourself.

Machinery Do not work in areas with direct exposure to sunlight.

During transfer, setup, and operations, avoid collisions with the

equipment.

Please check if the screws are fastened for a jig fixture installed with the
punch.

Do not use the equipment in areas with dust and water vapor.

2
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

1.2 Safety Information During Use

Item Description

Equipment Surroundings Please confirm there are if items interfering with punching and
and Operation pressing in the surroundings of the equipment.

While the equipment is active, do not enter the scope of operation of

the equipment.
While the Equipment is
Active While the equipment is active, if there are any unusual sounds or burnt
odors, stop the equipment right away and notify the Company (Delta
Electronics) or the contract service provider.

1.3 Safety Information During Maintenance and Under Other

Circumstances
Item Description

Make sure that the main power is off during checks and while oil is
Equipment Operation
being applied.
While the Equipment is While the equipment is being checked, do not reach into the scope
Active of operation of the equipment.

1.4 Powering System

Power Specifications Model

AM-ESP-E001-XXXX
AC single-phase three-wire AM-ESP-E002-XXXX
220V 50/60Hz, 10A AM-ESP-E005-XXXX
AM-ESP-E010-XXXX
AC three-phase four-wire AM-ESP-E030-XXXX
220V/380V 50/60Hz, 30A AM-ESP-E050-XXXX

3
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

2. Comprehensive System Structure

2.1 Model & Electronic Control Panel
The following figure uses the AM-ESP-E050-41XX as an example:

Servo motor

Gearbox
Cylinder

Loadcell

Wire cover

Servo driver

PLC & IO Module

4
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

3. Installation Setup
3.1 Fixed Way
3.1.1 AM-ESP-E050-XXXX/AM-ESP-E030-XXXX models
The fixed servo press is installed with a flange. The fastening ports are shown in the figure below.
Please use 8 general M12X1.75 hex screws (JIS strength is 12.9, length 60) and apply the tightening
torque of 1160 kgf-cm.

Suggested digging size

: Locking and fastening site

Caution: Please note that the equipment has to be closely attached to the locking and fastening
platform while fastening the servo press.

5
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

3.1.2 AM-ESP-E010-XXXX / AM-ESP-E005-XXXX models

The fixed servo press is installed with a flange. The fastening ports are shown in the figure below.
Please use 4 general M12X1.75 hex screws (JIS strength 12.9, length 45) and apply the tightening
torque of 1160 kgf-cm.

Suggested digging size

: Locking and fastening site

Caution: Please note that the equipment has to be closely attached to the locking and fastening
platform while fastening the servo press.

6
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

3.1.3 AM-ESP-E002-XXXX / AM-ESP-E001-XXXX models

The fixed servo press is installed with a flange. The fastening ports are shown in the figure below.
Please use 4 general M8X1.25 hex screws (JIS strength 12.9, length 25) and apply the tightening
torque of 334 kgf-cm.

Suggested digging size

: Locking and fastening site

Caution: Please note that the equipment has to be closely attached to the locking and fastening
platform while fastening the servo press.

7
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

3.2 Loading and Unloading Spindle Punch

Recommended punch jig design is provided in this section to facilitate realistic application by users.

3.2.1 AM-ESP-E050-XXXX / AM-ESP-E030-XXXX models

Please use M16x1.5 threads for the punch jig design.

Caution: The top of the spindle punch is installed with the load cell. Do not assemble tools in a way
that could result in deviations or impacts.

8
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

3.2.2 AM-ESP-E010-XXXX / AM-ESP-E005-XXXX models

Please use M8x1.25 threads for the punch jig design.

The design of the fixed punch should not be in contact with the entire surface of the front Loadcell .
It is recommended to design a neck structure to avoid full-surface contact with the front Loadcell.
inaccessible surface

Loadcell

accessible surface
Fixed punch

Neck

Caution: The top of the spindle punch is installed with the load cell. Do not assemble tools in a way
that could result in deviations or impacts.

9
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

3.2.3 AM-ESP-E002-XXXX / AM-ESP-E001-XXXX models

Please use M8x1.25 threads for the punch jig design.

The design of the fixed punch should not be in contact with the entire surface of the front Loadcell.
It is recommended to design a neck structure to avoid full-surface contact with the front Loadcell.
inaccessible surface

Loadcell

accessible surface
Fixed punch

Neck

Caution: The top of the spindle punch is installed with the load cell. Do not assemble tools in a way
that could result in deviations or impacts.

10
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

3.2.4 Restrictions of Jig

Punch dimensions and recommended jig designs are provided in the preceding three sections.
Extended descriptions and precautions are provided hereunder. See the table below:

Item Description

For the weight limits, please follow those shown in the catalog [front-
end load requirements of the spindle]. When the limits are exceeded,
Jig weight (Payload)
it will result in the spindle moving downwards due to gravity upon
shutdown.

The jig must be designed to overlap the core of the spindle.

Center of the jig Otherwise, the partial load phenomenon will damage the loaded
elements.

11
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

4. Equipment Care and Maintenance

4.1 Applying Oil to Equipment
The servo electric cylinder has been filled with grease at the factory, please replenish the screw lubricating
oil in time according to the usage conditions. Fill the oil hole as shown in the figure, and replenish it. In
order to maintain the service life of the machine, oil needs to be replenished regularly (assuming that it
operates 8 hours a day, it is recommended to refill oil once a year).

Oil hole

Mobil SHC220 grease is recommended. The operating temperature range of this grease is -40°C ~
+177°C
* Recommended oil gun: KCG-470H (Brand: Alba)
* Recommended nozzle: M6*1.0P, 40mm long
* Single oil injection volume_ E001 / E002 spindle: 5ml
* Single oil injection volume_ E005 / E010 spindle: 10ml
* Single oil injection volume_ E030 / E050 spindle: 40 ml

12
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

Oil filling steps are as follows:

Step 1: Remove the outer cover of the cylinder block wire cover
Step 2: Unscrew the screw plug of the oil injection hole
Step 3: Confirm the position of the oil nipple in the oil injection hole
Step 4: Stop the motor and cut off the power
Step 5: Combine the grease nipple with the oil hole and inject grease into the grease nipple
Step 6: Remove the grease fitting
Step 7: Screw on the screw plug
Step 8: Reinstall the cylinder block wire cover cover
Step 9: Turn on the power, and let the servo electric cylinder go back and forth for 2 to 3 full strokes

13
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

4.2 Load Cell Calibration

In order for the servo press to maintain precise quality, please perform load cell calibration if unusual
force levels appear, or perform load cell calibration on a regular basis (after the warranty period
expires). The load cell calibration tool is shown in the figure. Please follow the Operating Instructions
while performing calibration and qualification or contact the Company (Delta Electronics) or contract
service providers.

14
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

5. Wiring Instructions
5.1 Circuit Diagram

*During configurations, it is recommended that the signal line (green) and the motor power line (blue) be
routed separately.

15
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

5.2 Detailed Explanation of PLC External I/O Points

16
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

5.3 Wiring Instructions

17
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

5.4 Wire Table and Wire Size for Wiring

18
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

5.5 Details of Drive Power Distribution

#Suggest adding an NFB (No Fuse Breaker) circuit before the external power
supply to prevent damage to the driver.
5.5.1 0.4 kW~1 kW
0.4 kW ~ 1 kW

R
External
S power supply
(AC220V)
T
L1C
L2C
P1
P2

P3
D
C
U Red

V Write Motor power

(Power Cable)
Black
W

19
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

5.5.2 2 kW~5.5 kW
2 kW ~ 5.5 kW

L1C
L2C
R
External
power
supply S
(AC220V
/380V)
T
P1
P2
Regenerativ P3
e resistance
(5.5-7.5kW)
C
Red
U
Motor Write
power
(Power line)
V
Black
W

20
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

5.6 External Button

Cylinder type of servo press provide user to connect the button. The wires required for those button
including the two hand trigger buttons, emergency stop button, reset button, alarm light and buzzing.

(1) The wires showed at the red block and enlisted the table below: (NPN)

Input (Buttons)
EMS (NC) Mode Light Curtain (NC) Reset Trigger-L Trigger-R
*Mode-OFF is internal control，ON is external control

Output
Buzz Alarm

(2) How to use the button functions:

⚫ Turn on the button function.
1. Please log in [Senior Engineer] access (PW:2222)，touch [Equipment Parameter] and choose
[Other] 。

21
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

2. Please choose [Yes] with buttons, then press [Save].

3. Go back to main screen and touch the [IO Monitor] to check the status of the buttons

⚫ Trigger Start
The two hand start buttons have to be touched simultaneously to conduct the pressing process.
(<500ms). After the pressing finished, these two signal have to be released before next pressing
process.

⚫ Light Curtain
If the light curtain hasn’t been turned on, the hand two start buttons have to be touched during the
whole pressing process. If one of these buttons had been released, servo press will stop and go back to
working origin after touching the reset button.

If the light curtain is on, the two hand start button can be released after the pressing process begin.
If the curtain light have been installed, please follow the above steps to turn on the light curtain function.

1. Please log in [Senior Engineer] access (PW:2222)，touch [Equipment Parameter] and turn on
the light curtain.

22
Delta Electronics Servo Press E-Series Installation and Maintenance Instructions

23
Industrial Automation Headquarters
Taiwan: Delta Electronics, Inc.
Taoyuan Technology Center
No.18, Xinglong Rd., Taoyuan District,
Taoyuan City 33068, Taiwan
TEL: +886 - 3 - 362- 6301 / FAX: +886 -3 -371- 6301

Asia EMEA
China: Delta Electronics (Shanghai) Co., Ltd. EMEA Headquarters: Delta Electronics (Netherlands) B.V.
No.182 Minyu Rd., Pudong Shanghai, P.R.C. Sales: [email protected]
Post code : 201209 Marketing: [email protected]
TEL: +86 -21- 6872-3988 / FAX: +86 -21- 6872-3996 Technical Support: [email protected]
Customer Service: 400 - 820 - 9595 Customer Support: Customer- [email protected]
Service: [email protected]
Japan: Delta Electronics (Japan), Inc. TEL: +31(0) 40 800 3900
Industrial Automation Sales Department
2-1-14 Shibadaimon, Minato - ku BENELUX: Delta Electronics (Netherlands) B.V.
Tokyo, Japan 105 - 0012 De Witbogt 20, 5652 AG Eindhoven, The Netherlands
TEL: +81- 3 - 5733 -1155 / FAX: +81-3 - 5733 -1255 Mail: [email protected]
TEL: +31(0) 40 800 3900
Korea: Delta Electronics (Korea), Inc. DACH: Delta Electronics (Netherlands) B.V.
1511, 219, Gasan Digital 1- Ro., Geumcheon - gu,
Coesterweg 45, D - 59494 Soest, Germany
Seoul, 08501 South Korea
Mail: [email protected]
TEL: +82-2- 515 - 5305 / FAX: +82-2- 515 - 5302
TEL: +49(0)2921 987 0
Singapore: Delta Energy Systems (Singapore) Pte Ltd. France: Delta Electronics (France) S.A.
4 Kaki Bukit Avenue 1, #05 - 04, Singapore 417939 ZI du bois Challand 2, 15 rue des Pyrénées,
TEL: +65 - 6747- 5155 / FAX: +65 - 6744 - 9228 Lisses, 91090 Evry Cedex, France
Mail: [email protected]
India: Delta Electronics (India) Pvt. Ltd. TEL: +33(0)1 69 77 82 60
Plot No.43, Sector 35, HSIIDC Gurgaon,
PIN 122001, Haryana, India Iberia: Delta Electronics Solutions (Spain) S.L.U
TEL: +91-124 - 4874900 / FAX: +91-124 - 4874945 Ctra. De Villaverde a Vallecas, 265 1º Dcha Ed.
Hormigueras – P.I. de Vallecas 28031 Madrid
Thailand: Delta Electronics (Thailand) PCL. TEL: +34(0)91 223 74 20
909 Soi 9, Moo 4, Bangpoo Industrial Estate (E.P.Z), Carrer Llacuna 166, 08018 Barcelona, Spain
Pattana 1 Rd., T.Phraksa, A.Muang, Mail: [email protected]
Samutprakarn 10280, Thailand
TEL: +66 -2709 -2800 / FAX: +66 -2709 -2827 Italy: Delta Electronics (Italy) S.r.l.
Via Meda 2–22060 Novedrate(CO)
Australia: Delta Electronics (Australia) Pty Ltd. Piazza Grazioli 18 00186 Roma Italy
Unit 20 -21/45 Normanby Rd., Notting Hill Vic 3168, Australia Mail: [email protected]
TEL: +61- 3 - 9543 -3720 TEL: +39 039 8900365

Russia: Delta Energy System LLC

Americas Vereyskaya Plaza II, office 112 Vereyskaya str.
17 121357 Moscow Russia
USA: Delta Electronics (Americas) Ltd.
Mail: [email protected]
5101 Davis Drive, Research Triangle Park, NC 27709, U.S.A.
TEL: +7 495 644 3240
TEL: +1- 919 -767- 3813 / FAX: +1- 919 -767-3969
Turkey: Delta Greentech Elektronik San. Ltd. Sti. (Turkey)
Brazil: Delta Electronics Brazil Şerifali Mah. Hendem Cad. Kule Sok. No:16 - A
Rua Itapeva, 26 - 3°, andar Edificio Itapeva, 34775 Ümraniye – İstanbul
One - Bela Vista 01332- 000 - São Paulo - SP - Brazil Mail: [email protected]
TEL: +55 -12- 3932-2300 / FAX: +55 -12-3932-237 TEL: + 90 216 499 9910

Mexico: Delta Electronics International Mexico S.A. de C.V. MEA: Eltek Dubai (Eltek MEA DMCC)
Gustavo Baz No. 309 Edificio E PB 103 OFFICE 2504, 25th Floor, Saba Tower 1,
Colonia La Loma, CP 54060 Jumeirah Lakes Towers, Dubai, UAE
Tlalnepantla, Estado de México Mail: [email protected]
TEL: +52- 55 -3603 - 9200 TEL: +971(0) 4 2690148

*We reserve the right to change the information in this catalogue without prior notice.