Scribd
Upload
23 views2 pages

Welding Proceedure Project

The project requires the creation of a welding procedure specification and data sheet based on CSA W47.1 and CSA W59 standards, focusing on prequalified welding processes such as GMAW, FCAW, SMAW, and GTAW. Students must select a prequalified joint and use materials available in the welding lab, while also researching necessary welding parameters. The final submission must include a cover page and be submitted digitally via D2L.

Uploaded by

gebremikiasdemsis
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
23 views2 pages

Welding Proceedure Project

The project requires the creation of a welding procedure specification and data sheet based on CSA W47.1 and CSA W59 standards, focusing on prequalified welding processes such as GMAW, FCAW, SMAW, and GTAW. Students must select a prequalified joint and use materials available in the welding lab, while also researching necessary welding parameters. The final submission must include a cover page and be submitted digitally via D2L.

Uploaded by

gebremikiasdemsis
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

EMTL 201

CSA W47.1/W59 Welding Procedure Project 15%

Overview

Using your knowledge of CSA W47.1 and CSA W59, produce a welding procedure specification and welding procedure
data sheet that can be used for the criteria below. You will be required to use your codebooks to search for prequalified
criteria as well as recall your knowledge from welding processes in the shop. This project is to be completed individually.

Welding Processes

Welding processes will be limited to those covered in WDSG 235/275. GMAW, FCAW, SMAW and GTAW. You may create
a procedure which uses both if you wish. Ensure that you properly address all required criteria for the chosen
process(es).

Joint Preparation

Choose any prequalified joint from CSA W59 Figure 10.1 or Figure 10.2. It can be either complete or partial penetration.
Make sure all requirements of the prequalified joint are addressed and met in your procedures.

Materials

The materials used for construction and referenced in the required documentation must reflect what is actually
available in our welding lab. This includes:

• Base Materials: 1/8” – 1/2” ASTM A36 Plate (Steel Group 1 in Table 11.1)

• Filler Materials: GMAW: E70S-6, FCAW: E70T-6, SMAW: E6010, E7018. GTAW: ER70S-2

• Shielding Gases (if applicable): 100% Argon, 95% Argon 5% CO2 Mixed, 75% Argon 25% CO2 Mixed.

• Any other materials used in construction

Welding Parameters

Welding parameters must be researched when creating these procedures. Recall information from your time in the
welding shop or resources from other classes. This includes:

• Amperage

• Current Polarity

• Welding Speed

• Number of Passes

EMTL 201 April 3, 2020 Rev. 1


WELDING ENGINEERING TECHNOLOGY - DO NOT DUPLICATE ©
Required Documents

The following documents are required for the project:

1. Cover Page – Your Format

2. Welding Procedure Specification - Your Format

3. Welding Procedure Data Sheet - Your Format

Samples and suggested information can be found in the Annexes of CSA W47.1.

Reference Code Documents

The following reference documents are required to be used for this project:

• CSA W47.1

• CSA W59

Submission

Please submit your documentation in the order listed in this document. Include a cover page that includes:

• Name

• Student Number

• Date of Submission

For final submission of the project documentation, a digital copy is required. Please submit via D2L.

EMTL 201 April 3, 2020 Rev. 1


WELDING ENGINEERING TECHNOLOGY - DO NOT DUPLICATE ©

You might also like