HYDRAULIC MOTORS MVM

APPLICATION
A A
» Conveyors
» Metal working machines
» Agricultural machines
» Road building machines
» Mining machinery
» Food industries B B
» Special vehicles
» Plastic and rubber machinery etc.
OPTIONS
» Model - Disc valve, roll-gerotor
» Flange with wheel mount
CONTENTS » Short motor
» Side ports
Specification data ............................ 44
» Shafts - straight, splined and tapered
Function diagrams ..................... 45-47 » BSPP ports Metric, SAE and BSPP ports;
Dimensions and mounting MVM ...... 48 » Other special features.
Mounting Flanges ............................ 49
Port Types ....................................... 49
EXCELLENCE
Shaft extensions ............................ 50 » High torque and pressure drop
Permissible shaft Seal Pressure .... 51 » High inlet pressure
» High starting torque
Order code ...................................... 51
» Improved efficiency at high pressure drop
and frequent reversing
» Smooth operation at low speed
GENERAL » High radial and axial bearing capacity

3 3
Max. Displacement, cm /rev [in /rev] 801,8 [48.91]
Max. Speed, [RPM] 763
Max. Torque, daNm [lb-in] cont.: 259 [22920] int.: 340 [30090]
Max. Output, kW [HP] 112 [150]
Max. Pressure Drop, bar [PSI] cont.: 250 [3630] int.: 350 [5080]
Max. Oil Flow, lpm [GPM] 240 [63.4]
Min. Speed, [RPM] 5
Permissible Shaft Loads, daN [lbs] Pa=1500 [3370]
Pressure fluid Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Temperature range,
O O
C [ F] -40÷140 [-40÷284]
Optimal Viscosity range, mm /s [SUS]
2 20÷75 [98÷347]

Filtration ISO code 20/16 (Min. recommended fluid filtration of 25 microns)

Oil flow in drain line Pressure Losses

30
400
25
Pressure drop Viscosity Oil flow in
2 drain line 300 20
bar [PSI] mm /s [ SUS] lpm [GPM ]
15
20 [98] 3 [.793] 200
140 [2030] 10
35 [164] 2 [ .528 ]
100
5
20 [98] 6 [ 1.585 ]
210 [ 3045] 0 0
35 [164] 4 [1.057] 0 25 50 75 100 125 150 175 200 Q, lpm

0 5 10 15 20 25 30 35 40 45 50 Q, GPM
43
 MVM
MOTORS

SPECIFICATION DATA

Type MVM MVM MVM MVM MVM

315 400 500 630 800
3 3
Displacement, cm /rev [in /rev] 314,5 [19.19 ] 400,9 [ 24.5 ] 499,6 [ 30.5] 629,1 [ 38.38] 801,8 [ 48.91]
Max. Speed, cont. 636 500 400 315 250
[RPM] Int.* 763 600 480 380 300
Max. Torque cont. 115 [10180] 144 [12745] 180 [15930] 227 [20090] 259 [22920]
daNm [lb-in] Int.* 160 [14160] 200 [17700] 260 [23010] 310 [27440] 340 [30090]
peak** 180 [15930] 230 [20355] 286 [25315] 360 [31860] 402 [35580]
Max. Output cont. 67 [90] 67 [90] 67 [90] 67 [90] 67 [90]
kW [HP] int.* 112 [150] 112 [150] 112 [150] 112 [150] 112 [150]
Max. Pressure Drop cont. 250 [3630] 250 [3630] 250 [3630] 250 [3630] 225 [3263]
bar [PSI] Int.* 350 [5080] 350 [5080] 350 [5080] 350 [5080] 300 [4350]
peak** 400 [5800] 400 [5800] 400 [5800] 400 [5800] 350 [5080]
Max. Oil Flow cont. 200 [52.8] 200 [52.8] 200 [52.8] 200 [52.8] 200 [52.8]
lpm [GPM] Int.* 240 [63.4] 240 [63.4] 240 [63.4] 240 [63.4] 240 [63.4]
Max. Inlet Pressure cont. 270 [3915] 270 [3915] 270 [3915] 270 [3915] 270 [3915]
bar [PSI] Int.* 370 [5365] 370 [5365] 370 [5365] 370 [5365] 370 [5365]
peak** 420 [6090] 420 [6090] 420 [6090] 420 [6090] 420 [6090]
Max. Return Pressure cont. 140 [2030] 140 [2030] 140 [2030] 140 [2030] 140 [2030]
with Drain Line Int.* 175 [2540] 175 [2540] 175 [2540] 175 [2540] 175 [2540]
bar [PSI] peak** 210 [3045] 210 [3045] 210 [3045] 210 [3045] 210 [3045]
Max. Starting Pressure with Unloaded Shaft,
bar [PSI] 5 [70] 5 [70] 5 [70] 5 [70] 5 [70]
Min. Starting Torque daNm [lb-in] 92 [8140] 115 [10180] 144 [12745] 180 [15930] 205 [18145]
Min. Speed***, [RPM] 10 6 8 6 5
Weight, kg [lb] MVM 41,3 [91] 42,1 [93] 43 [95] 44,5 [98] 46 [101.4]
MVMC 43,8 [96.6 ] 44,9 [99 ] 45,8 [ 101 ] 48,3 [ 106.5 ] 50,4 [ 111.1]

* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.

1. Intermittent speed and intermittent pressure must not occur simultaneously.

2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
2
4. Recommended minimum oil viscosity 13 mm /s [70 SUS] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

44
 MVM
MOTORS
FUNCTION DIAGRAMS

MVM 315
M M
Q=20 l/min
5.3 GPM

40 l/min
10.6 GPM

80 l/min
21.13 GPM

120 l/min
31.7 GPM

160 l/min
42.3 GPM

200 l/min
52.8 GPM

240 l/min
63.4 GPM
lb-in daNm

14000 160

140 p=350 bar

12000 5075 PSI
300 bar
int.

120 4350 PSI

10000 85 kW
250 bar
100 3625 PSI
8000 60 kW 70 kW
cont.

200 bar
80 2900 PSI

6000 50 kW
60 150 bar
2175 PSI
90% 40 kW
4000
30 kW
100 bar
40 1450 PSI
20 kW
87% 10 kW
2000 20
50 bar
ht=80% 730 PSI
84% N=5 kW
0 0
cont. int.
n
0 75 150 225 300 375 450 525 600 675 750 min-1 (rpm)

MVM 400
M M
Q=20 l/min
5.3 GPM

40 l/min
10.6 GPM

80 l/min
21.13 GPM

120 l/min
31.7 GPM

160 l/min
42.3 GPM

200 l/min
52.8 GPM

240 l/min
63.4 GPM

lb-in daNm

210
18000 p=350 bar
5075 PSI
180
15000 300 bar
int.

4350 PSI
90 kW
150
250 bar
12000 70 kW 3625 PSI
120
cont.

200 bar
9000 2900 PSI
84%
90 50 kW
150 bar
2175 PSI
6000 90% 40 kW
60 100 bar
10 kW 20 kW 30 kW 1450 PSI
3000 30 N=5 kW
50 bar
730 PSI
ht=82%
88%
0 0
cont. int.
n
-1
0 60 120 180 240 300 360 420 480 540 600 min (rpm)

The function diagrams data was collected at back pressure 5÷10 bar [72.5÷145 PSI]
O
and oil with viscosity of 32 mm²/s [150 SUS] at 50° C [122 F].
45
 MVM
MOTORS

FUNCTION DIAGRAMS

MVM 500
M M
Q=20 l/min
5.3 GPM

40 l/min
10.6 GPM

80 l/min
21.13 GPM

120 l/min
31.7 GPM

160 l/min
42.3 GPM

200 l/min
52.8 GPM

240 l/min
63.4 GPM
lb-in daNm

24000 275

22000 250
p=350 bar
20000 225 5075 PSI
18000 300 bar
int.

200 4350 PSI

16000 250 bar
175
3625 PSI
14000 75 kW
150
cont.

12000 200 bar

2900 PSI
125 60 kW
10000 150 bar
100 2175 PSI
8000
40 kW
75 100 bar
6000 90%
88% 25 kW 1450 PSI
4000 50
50 bar
86%
2000 25 N=5 kW 730 PSI
ht=84% 10 kW
0 0
cont. int. n
0 50 100 150 200 250 300 350 400 450 500 min-1 (rpm)

MVM 630
M M
Q=20 l/min
5.3 GPM

40 l/min
10.6 GPM

80 l/min
21.13 GPM

120 l/min
31.7 GPM

160 l/min
42.3 GPM

200 l/min
52.8 GPM

240 l/min
63.4 GPM

lb-in daNm

32000
350

28000 p=350 bar

300 5075 PSI
int.

100 kW
24000 300 bar
250 4350 PSI
70 kW 90 kW
20000 250 bar
80 kW 3625 PSI
cont.

200
16000 200 bar
50 kW
60 kW 2900 PSI
150
12000 150 bar
30 kW 2175 PSI
40 kW
100
8000 100 bar
90% 1450 PSI
ht=84% 20 kW

4000 50 50 bar
86% 88% 730 PSI
N=5 kW 10 kW
0 0 cont. int.
n
0 40 80 120 160 200 240 280 320 360 400 min-1 (rpm)

The function diagrams data was collected at back pressure 5÷10 bar [72.5÷145 PSI]
O
and oil with viscosity of 32 mm²/s [150 SUS] at 50° C [122 F].
46
 MVM
MOTORS
FUNCTION DIAGRAMS

MVM 800
M M

Q=20 l/min
5.3 GPM
40 l/min
10.6 GPM

80 l/min
21.13 GPM

120 l/min
31.7 GPM

160 l/min
42.3 GPM

200 l/min
52.8 GPM

240 l/min
63.4 GPM
lb-in daNm

32000 360
p=300 bar
28000 320 4350 PSI

260 bar
int.

280
24000 3770 PSI
75 kW 225 bar
240 3260 PSI
20000

200
cont.

60 kW
16000
150 bar
160 2175 PSI
40 kW
12000 90%
120
100 bar
8000 25 kW 1450 PSI
80
88% 10 kW
50 bar
4000 40 730 PSI
ht=82% 85%
N=5 kW
0 0
cont. int. n
0 50 100 150 200 250 300 350 min-1 (rpm)

The function diagrams data was collected at back pressure 5÷10 bar [72.5÷145 PSI]
O
and oil with viscosity of 32 mm²/s [150 SUS] at 50° C [122 F].

PERMISSIBLE SHAFT LOADS

The output shaft runs in tapered bearings that permit high axial and radial forces. Curve "1" shows max. radial shaft
load. Any shaft load exceeding the values shown by the curve will seriously reduce motor life. The two other curves
apply to a B10 bearing life of 3000 hours at 200 RPM.

Prad Prad
daN -4 -3 -2 -1 0 1 in lbs
14000
6000
1
1500 daN 2
3370 lbs. 12000
5000 1500 daN
3370 lbs.
10000 3 - Pa=1500 daN [3370 lbs]
4000
2 - Pa=0 daN [0 lbs]
8000

3000
3 6000

2000
4000

1000 2000

-125 -100 -75 -50 -25 0 25 50 mm

47
 MVM
MOTORS DIMENSIONS AND MOUNTING DATA MVM and MVMC
K Shaft T Shaft B Shaft C Shaft CO Shaft G Shaft SH Shaft S Shaft

145 [5.7]
140 [5.5]
139 [5.47]
max 122 [4.8]
max 117 [4.6]
S Shaft SH Shaft G Shaft CO Shaft C Shaft B Shaft T Shaft K Shaft

max 115 [4.5]

120 [4.7]
137 [5.39]
L1

ø160 [6.3]
138 [5.4]

P(A,B)
L2

143 [5.6]
L max

63 [2.48]

Port Dim.
See Page 49

Shaft Dim.
T See Page 50 T
Port A
L2

Port B
ø160 [6.3]
L max

L1

P(A,B)
Versions
2 3 4 5
P (A,B) 2xG1 2xG1 2x15/ 16 -12UN 2x1” (SAE PSI3000)
9
T G¼ G¼ / 16 -18UNF G¼
C - 6xM10 - 8xM10

Port A
Port B
C
mm [in]
L3

Port A
L max

Standard Rotation Reverse Rotation

Viewed from Shaft End Viewed from Shaft End Port B
Port A Pressurized - CW Port A Pressurized - CCW
Port B Pressurized - CCW Port B Pressurized - CW

Warning: Drain line should always be used (if no check valves)!

Type Lmax, mm [in] L2, mm [in] L3, mm [in] Type Lmax, mm [in] L2, mm [in] L3, mm [in] L1, mm [in]
MVM 315 226,5 [8.92] 172,5 [6.79] 157,4 [6.20] MVMC 315 227,5 [8.957] 173,8 [6.84] 158,7 [6.25] 25,5 [1.00]
MVM 400 233,5 [9.19] 179,5 [7.07] 164,4 [6.47] MVMC 400 234,5 [9.232] 180,8 [7.12] 165,7 [6.52] 32,5 [1.28]
MVM 500 241,5 [9.51] 187,5 [7.38] 172,4 [6.79] MVMC 500 242,5 [9.547] 188,8 [7.43] 173,7 [6.84] 40,5 [1.59]
MVM 630 252,0 [9.92] 198,0 [7.79] 182,9 [7.20] MVMC 630 253,0 [9.961] 199,3 [7.85] 184,2 [7.25] 51,0 [2.01]
MVM 800 266,0 [10.47] 212,0 [8.35] 196,9 [7.75] MVMC 800 267,0 [10.518] 213,3 [8.39] 198,2 [7.80] 65,0 [2.56]
48
 MVM
MOTORS MOUNTING
Square Mount (4 Holes)
60 [2.36]
ø200±0,4 4xø18
[7.87±.016] [.708]

179 [7.05]

ø160 -0,063
[6.3 -.0025]
20±0,3 11+0,2
85-0,5
[.787±.012] [.433+.0079]
[3.35-.0196 ]
179 [7.05]
C Square Mount (four holes)
(194 [7.638])

85-0,5 30 o ø224 63 [2.48]

[3.346 -.0197]
[8.819]

(194 [7.638])

ø180 [7.087]
mm [in]
ø200 2x M10 4x ø18 23 8,8±0,2
[7.874] Thru. [.709] [.91] [.346]

PORTS
Side Ports
Versions 2 4 Versions 3 Versions 5
28,5±0,2
[1.97±.0059]

[1.12±.00787]
[2.06±.0118]
[1.97±.0059]
50±0,15

52,4±0,3
50±0,15

P(A,B) 18±0,2 18±0,2

T
(26,2 [1.03])

[.708±.00787] [.708±.00787] (13,1 [.52])

C
[.78±.0039]
19,8±0,1

Port A Port A Port A

26,2±0,15
P(A,B)
[5.7±.0197]

[1.03±.0059]
160 [6.299]

145±0,5

2,5±0,5
P(A,B)
[.098±.02]
[.78±.0039]
19,8±0,1

Port B Port B
Port B C
(13,1 [.52])
(26,2 [1.03])
[1.97±.0059]

[2.06±.0118]
[1.97±.0059]

52,4±0,3
50±0,15

7,5±0,2 26,2±0,15
50±0,15

[.29±.00787] [1.03±.0059]

18±0,2 18±0,2
15±0,15 21±0,15
[.708±.00787] [.708±.00787]
[.59±.0059] [.827±.0059]
21±0,15
[.827±.0059]

R80
[3.15] Standard Rotation Reverse Rotation
Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
Port B Pressurized - CCW Port B Pressurized - CW
[6.3±.06]
160±1,5

Versions
2 3 4 5
P (A,B) 2xG1 2xG1 2x15/ 16 -12UN 2x1” (SAE PSI3000)
9
T G¼ G¼ / 16 -18UNF G¼
85 [3.35]

165 [6.5]
C - 6xM10 - 8xM10

49
 MVM
MOTORS
SHAFT EXTENSIONS
C - ø50 straight, Parallel key A14x9x70 DIN 6885 CO - ø2¼" [57,15] straight
Parallel key ½ "x½"x 2¼" BS46

14 -0,043 12,72-0,02 79 [3.11]

79 [3.11] [.502-.0008]
[.551-0017]
[2.086+.0079 ]

[2.48-.0079]
]

ø57,15 -0,015
ø60 [2.362]
ø62,9 -0,2
ø60 [2.362]
+.0197

[2.25-.0006]
+.0008
[1.968+.0007
+0,018
ø50+0,002
+0,5
ø53+0,2

M12 3/8-16 UNC

min 26 [1.024] deep min 25 [.98] deep

SH - ø2 1/8 " (ø53,975) splined B - ø2¼" [57,15] straight

16 DP 8/16 ANS B92.1-1976 Parallel key ½ "x½"x 2¼" BS46

79 [3.11]
12,72 -0,02 57,5 -0,5
56+2 [.5 -.00078] [2.26 -.02]
[2.205 +.079 ]
ø53,975 -0,025
ø60 [2.362]

ø60 [2.362]
[2.125-.001]

[2.46-.0079]
62,6 -0,2
M12 1/2-20 UNF 99±0,2
min 26 [1.024] deep ANSI B1.1-1982 [3.9±.0078]
min 26 [1.024] deep

G - ø2 1/8 " [53,975] splined K - ø60, tapered 1:10

16 DP 8/16 ANS B92.1-1976 Parallel key B16x10x32 DIN 6885

70 [2.756] 7 S=65
[.275] Tightening Torque
A 70±1 daNm
79 [3.11] A-A
16-0,043 [6196±88.5 lb-in]
+2 40
56 [.63-.0017] [1.575]
[2.205+.079 ]
[.315]
ø8
ø53,975 - 0,025
ø60 [2.362]

[2.125 - .001]

ø60 [2.362]

ø78 [3.01]
M42x3
[2.27-.0079 ]
32,25 -0,2

Taper 1:10 A
3/8-16 UNC
6
ANSI B1.1-1982
105 [4.134] [.236]
min 26 [1.024] deep

S - ø2 1/8 " [53,975] splined T - ø2¼9 " [57,15]

9
SAE J501, tapered 1:8
16 DP 8/16 ANS B92.1-1976 key /16"x /16"x2" BS46
11/2-18 UNEF-2A
ANSI B1.1-1982

A-A
14,308 -0,02
A
55,8±0,5 [.56 -.00078]
[2.2±.02]
ø4 [.16]
ø53,975 - 0,025

ø57,2 [2.25]
ø60 [2.362]

[2.125 - .001]

[.33 - .006 ]
8,3 -0,15

A
1/2-20 UNF Taper 1:8 4,5 [.18]
76,7±0,2
ANSI B1.1-1982 [3.02±.0079] 73 [2.87]
min 26 [1.024] deep
100 [3.94]
mm [in]
50
 MVM
MOTORS

MAX. PERMISSIBLE SHAFT SEAL PRESSURE

Max. return pressure without drain line or
max. pressure in the drain line

P P
PSI bar
1200

1000

800
1: Drawing for High Pressure Seal ("U" Seal)
2: Drawing for Standard Shaft Seal
600
1

400 2 - continuous operations

- intermittent operations
200

0 -1
min

ORDER CODE

1 2 3 4 5 6 7 8

MVM HD

Pos.1 - Mounting Flange Pos.4 - Ports

omit - Standard square mount, four holes 2 - side ports 2xG1, G1/4, BSP thread, ISO 228
C - Square mount, four holes 3 - side ports 2xG1, G1/4, BSP thread, ISO 228,
Pos.2 - Displacement code 6xM10
315 - 314,5 cm3/rev [19.80 in3/rev] 4 - side ports 2x1 5/16-12 UN, O-ring, 9/16-18 UNF
3 3
400 - 400,9 cm /rev [24.45 in /rev] 5 - side ports 2x1” (SAE PSI3000), G1/4,
3 3
500 - 499,6 cm /rev [30.48 in /rev] BSP thread,SO 228, 8xM10
3 3
630 - 629,1 cm /rev [38.38 in /rev] Pos.5 - Check Valves
3 3
800 - 801,8 cm /rev [48.91 in /rev] omit - without check valves
1 - with check valves
Pos.3 - Shaft Extensions*
C - ø50 straight, Parallel key A14x9x70 DIN6885 Pos.6 - Shaft Seal Version (see page 50)
1 1
CO - ø2¼" [57,15] straight, Parallel key /2"x /2"x2¼" BS46 omit - Low pressure shaft seal
1 1
B - ø2¼" [57,15] straight, Parallel key /2"x /2"x2¼" BS46 U - High pressure shaft seal
1
SH - ø2 /8" [53,975] splined, 16DP 8/16 ANS B92.1-1976
1 Pos.7 - Special Features
G - ø2 /8" [53,975] splined, 16DP 8/16 ANS B92.1-1976
1 HD - Reinforced motor HD**
S - ø2 /8" [53,975] splined, 16DP 8/16 ANS B92.1-1976
For Other Special Features see page 58
K - ø60 tapered 1:10, Parallel key B16x10x32 DIN6885
T - ø2¼" [57,15] SAE J501, tapered 1:8, Pos.8 - Design Series
9 9
key /16"x /16"x2" BS46 omit - Factory specified

NOTES:
* The permissible output torque for shafts must not be exceeded!
** Drain line should always be used (if no check valves).

The hydraulic motors are mangano-phosphatized as standard.

51