INTERNATIONAL ISO
STANDARD 5610-2
First edition
2010-08-01
Tool holders with rectangular shank for
indexable inserts —
Part 2:
Style A
Porte-plaquette à queue rectangulaire pour plaquettes amovibles —
iTeh STANDARD
Partie 2: Forme A PREVIEW
(standards.iteh.ai)
ISO 5610-2:2010
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
8abe02f0da33/iso-5610-2-2010
Reference number
ISO 5610-2:2010(E)
© ISO 2010
ISO 5610-2:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 5610-2:2010
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
8abe02f0da33/iso-5610-2-2010
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail
[email protected] Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 5610-2:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5610-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with
cutting edges made of hard cutting materials.
iTeh STANDARD PREVIEW
This first edition of ISO 5610-2, together with ISO 5610-1, ISO 5610-3, ISO 5610-4, ISO 5610-5, ISO 5610-6,
ISO 5610-7, ISO 5610-8, ISO 5610-9, ISO 5610-10, ISO 5610-11, ISO 5610-12, ISO 5610-13, ISO 5610-14
(standards.iteh.ai)
and ISO 5610-15, cancels and replaces ISO 5610:1998.
ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank for
indexable inserts: ISO 5610-2:2010
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
⎯ Part 1: General survey, correlation and determination of dimensions
8abe02f0da33/iso-5610-2-2010
⎯ Part 2: Style A
⎯ Part 3: Style B
⎯ Part 4: Style D
⎯ Part 5: Style F
⎯ Part 6: Style G
⎯ Part 7: Style J
⎯ Part 8: Style K
⎯ Part 9: Style L
⎯ Part 10: Style N
⎯ Part 11: Style R
⎯ Part 12: Style S
⎯ Part 13: Style T
⎯ Part 14: Style H
⎯ Part 15: Style V
© ISO 2010 – All rights reserved iii
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 5610-2:2010
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
8abe02f0da33/iso-5610-2-2010
INTERNATIONAL STANDARD ISO 5610-2:2010(E)
Tool holders with rectangular shank for indexable inserts —
Part 2:
Style A
1 Scope
This part of ISO 5610 specifies tool holders with rectangular shank, style A, i.e. with straight shank and cutting
edge angle κr = 90° for side cutting.
These tool holders are primarily intended for indexable inserts made of hardmetal or other cutting materials
intended to be mounted by clamping and used for turning operations.
NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred
symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2010, Table A.1.
2 iTeh STANDARD PREVIEW
Normative references
(standards.iteh.ai)
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5610-2:2010
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
ISO 5608:1995, Turning and copying 8abe02f0da33/iso-5610-2-2010
tool holders and cartridges for indexable inserts — Designation
ISO 5610-1:2010, Tool holders with rectangular shank for indexable inserts — Part 1: General survey,
correlation and determination of dimensions
3 Dimensions
3.1 General
It is not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall
be observed.
For determination of dimensions h1, f and l1, see ISO 5610-1.
For explanation of the designation code for tool holders, see ISO 5608.
NOTE The values of rake angles and inclination angles shown in the figures are recommended values; they can vary
according to the application.
© ISO 2010 – All rights reserved 1
ISO 5610-2:2010(E)
3.2 Tool holder style A for rhombic indexable insert shape C
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 5610-2:2010
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
8abe02f0da33/iso-5610-2-2010
NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.
a Inclination angle λn. b Rake angle γn.
Figure 1 — Tool holder style A for rhombic indexable insert — C
Table 1
Dimensions in millimetres
h1 b l3 f h2 l1a l2 sb
Symbola +0,5
js13 h13 ≈ 0
h13 k16 max.
SCACR 0808 — 06
8 8 6,4 8,5 8 — 12 2,38
SCACL 0808 — 06
SCACR 1010 — 06
10 10 6,4 10,5 10 — 12 2,38
SCACL 1010 — 06
a For the selection of length, l1, the en-dash may be replaced by the dimensions of ISO 5610-1:2010, Table 2. For the letter symbols
identifying the tool length, see ISO 5608:1995, Table 6.
b Insert thickness without shim, if any.
2 © ISO 2010 – All rights reserved
ISO 5610-2:2010(E)
3.3 Tool holder style A for triangular indexable insert shape T
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 5610-2:2010
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
8abe02f0da33/iso-5610-2-2010
NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.
a Inclination angle λn.
b Rake angle γn.
Figure 2 — Tool holder style A for triangular indexable insert — T
© ISO 2010 – All rights reserved 3
ISO 5610-2:2010(E)
Table 2
Dimensions in millimetres
h1 b l3 f h2 l1a l2 sb
Symbola
+0,5
js13 h13 ≈ 0
h13 k16 max.
STACR 1212 — 11
2,38
STACL 1212 — 11
PTANR 1212 — 11
12 12 11 12,5 12 — 25
PTANL 1212 — 11
3,18
CTAPR 1212 — 11
CTAPL 1212 — 11
STACR 1616 — 11
2,38
STACL 1616 — 11
PTANR 1616 — 11
16 16 11 16,5 16 — 25
PTANL 1616 — 11
3,18
CTAPR 1616 — 11
CTAPL 1616 — 11
STACR 2020 — 16
3,97
STACL 2020 — 16
PTANR 2020 — 16
20 20 16,5 20,5 20 — 32 4,76
PTANL 2020 — 16
CTAPR 2020 — 16
CTAPL 2020 — 16
iTeh STANDARD PREVIEW 3,18
STACR 2525 — 16 (standards.iteh.ai) 3,97
STACL 2525 — 16
PTANR 2525 — 16
ISO 5610-2:2010
25 25 16,5 25,5 25 —
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba- 32 4,76
PTANL 2525 — 16
8abe02f0da33/iso-5610-2-2010
CTAPR 2525 — 16
3,18
CTAPL 2525 — 16
STACR 3225 — 16
3,97
STACL 3225 — 16
PTANR 3225 — 16
32 25 16,5 25,5 32 — 32 4,76
PTANL 3225 — 16
CTAPR 3225 — 16
3,18
CTAPL 3225 — 16
STACR 3232 — 22
STACL 3232 — 22
PTANR 3232 — 22
32 32 22 33 32 — 35 4,76
PTANL 3232 — 22
CTAPR 3232 — 22
CTAPL 3232 — 22
STACR 4040 — 22
STACL 4040 — 22
PTANR 4040 — 22
40 40 22 41 40 — 36 4,76
PTANL 4040 — 22
CTAPR 4040 — 22
CTAPL 4040 — 22
a See Table 1.
b See Table 1.
4 © ISO 2010 – All rights reserved
ISO 5610-2:2010(E)
4 Designation
A tool holder in accordance with this part of ISO 5610 shall be designated by:
a) “Tool holder”;
b) reference to this part of ISO 5610, i.e. ISO 5610-2;
c) type of mounting, in accordance with ISO 5608;
d) symbol for indexable insert shape, in accordance with ISO 5608;
e) symbol for tool style, in accordance with ISO 5608;
f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;
g) symbol for hand of tool, in accordance with ISO 5608;
h) its height, h1, width, b, and length, l1 (symbol for tool length in accordance with ISO 5608);
i) its cutting edge length, l3.
EXAMPLE 1 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style A (A), for
normal clearance of indexable insert αn = 7° (C), right-hand type (R), with height h1 = 10 mm and width b = 10 mm (1010),
length l1 = 70 mm (E), for cutting edge length l3 = 6,4 mm (06) is designated as follows:
iTeh STANDARD PREVIEW
Tool holder ISO 5610-2 - SCACR 1010 E06
EXAMPLE 2
(standards.iteh.ai)
Tool holder for a horizontally mounted, bore-clamped (P) triangular indexable insert shape T (T), tool
holder style A (A), normal clearance of indexable insert αn = 0° (N), right-hand type (R), with height h1 = 32 mm and width
ISO 5610-2:2010
b = 25 mm (3225), length l1 = 170 mm (P), for cutting edge length l3 = 16,5 mm (16) is designated as follows:
https://standards.iteh.ai/catalog/standards/sist/66db4003-d9d5-4a39-8aba-
Tool holder ISO 5610-2 - PTANR 3225 8abe02f0da33/iso-5610-2-2010
P16
5 Material
The material should be steel with a tensile strength of at least 1 200 N/mm2.
6 Design
6.1 Type of mounting
Standard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.
Other types of mounting may be left to the manufacturer's discretion or upon agreement. The letter symbol in
the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon
type of mounting, in accordance with ISO 5608.
For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall
also be considered.
6.2 Corner radius, rε
Tool holders in accordance with this part of ISO 5610 may be equipped with indexable inserts with cutting
edge lengths, l3, as specified in Tables 1 and 2 and any corner radius, rε.
© ISO 2010 – All rights reserved 5
