Design File for

Steel Column Temp. Connection

Project:
Project no:
Author:

Project item Temp Connection

Design
Name Temp Connection
Description
Analysis Stress, strain/ simplified loading
Design code AISC - LRFD (2022)

Members

Geometry
β – Direction γ - Pitch α - Rotation Offset ex Offset ey Offset ez
Name Cross-section
[°] [°] [°] [mm] [mm] [mm]
B1 2 - I600 0.0 -90.0 0.0 0 0 0
B2 2 - I600 0.0 90.0 180.0 100 0 0

Supports and forces

X
Name Support Forces in
[mm]
B1 / end Node 0
B2 / end N-Vy-Vz-Mx-My-Mz Node 0

1 / 23
Project:
Project no:
Author:

Cross-sections
Name Material
2 - I600 A572 Gr.50

Bolts
Diameter fy fu Gross area
Name
[mm] [MPa] [MPa] [mm2]
24 A325M 24 660.0 830.0 452

Load effects (Equilibrium not required)

N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B1 / End 83.0 41.5 -41.5 0.0 83.0 83.0
LE2 B1 / End 150.0 75.0 75.0 0.0 262.5 262.5

Check

Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.4 < 5.0% OK
Bolts 79.9 < 100% OK
Welds 87.4 < 100% OK
Buckling 6.62

2 / 23
Project:
Project no:
Author:

Plates
tp σEd εPl σc,Ed
Name Loads Status
[mm] [MPa] [%] [MPa]
B1-bfl 1 100.0 LE2 41.6 0.0 0.0 OK
B1-tfl 1 100.0 LE2 43.0 0.0 0.0 OK
B1-w 1 100.0 LE2 79.8 0.0 0.0 OK
B2-bfl 1 100.0 LE2 49.9 0.0 0.0 OK
B2-tfl 1 100.0 LE2 49.8 0.0 0.0 OK
B2-w 1 100.0 LE2 103.5 0.0 0.0 OK
SP1 15.0 LE2 310.7 0.2 17.5 OK
SP2 15.0 LE2 310.7 0.2 19.1 OK
SP3 15.0 LE2 310.7 0.2 22.2 OK
SP4 15.0 LE2 311.2 0.4 17.0 OK
SP5 15.0 LE2 310.5 0.1 17.5 OK
SP6 15.0 LE2 310.6 0.2 18.8 OK
SP7 15.0 LE2 303.1 0.0 22.2 OK
SP8 15.0 LE2 276.4 0.0 20.8 OK
SP9 15.0 LE2 114.6 0.0 4.4 OK
SP10 15.0 LE2 283.5 0.0 16.0 OK
SP11 15.0 LE2 267.8 0.0 12.6 OK
SP12 15.0 LE2 112.0 0.0 11.9 OK
SP13 15.0 LE2 103.7 0.0 15.8 OK
SP14 15.0 LE2 304.6 0.0 17.5 OK
SP15 15.0 LE2 137.2 0.0 8.0 OK
SP16 15.0 LE2 296.6 0.0 21.0 OK
SP17 15.0 LE2 292.6 0.0 21.0 OK
SP18 15.0 LE2 180.9 0.0 11.9 OK
SP19 15.0 LE2 248.9 0.0 15.8 OK
SP20 15.0 LE2 310.6 0.2 17.5 OK

Design data

Fy εlim
Material
[MPa] [%]
A572 Gr.50 344.7 5.0

Symbol explanation
tp Plate thickness
σEd Equivalent stress
εPl Plastic strain
σc,Ed Contact stress
Fy Yield strength
εlim Limit of plastic strain

3 / 23
 Project:
Project no:
Author:

Detailed result for SP4

Design values used in the analysis

ϕFy =
​
310.3 MPa

Where:
Fy = 344.7 MPa – characteristic yield strength
​

ϕ = 0.90 – resistance factor for steel material AISC 360-22 – B3.1

Overall check, LE2

4 / 23
 Project:
Project no:
Author:

Strain check, LE2

Equivalent stress, LE2

5 / 23
Project:
Project no:
Author:

Bolts
Ft V ϕRn,bearing Utt Uts Utts
Shape Item Grade Loads Detailing Status
[kN] [kN] [kN] [%] [%] [%]
B1 24 A325M - 1 LE2 20.3 75.1 290.4 9.7 59.6 0.0 OK OK
B2 24 A325M - 1 LE2 6.1 69.1 290.4 2.9 54.8 0.0 OK OK
B3 24 A325M - 1 LE2 8.0 64.8 282.5 3.8 51.4 0.0 OK OK
B4 24 A325M - 1 LE2 23.5 87.2 290.4 11.2 69.2 0.0 OK OK
B5 24 A325M - 1 LE2 5.7 68.7 290.4 2.7 54.5 0.0 OK OK
B6 24 A325M - 1 LE2 9.7 67.8 290.4 4.6 53.8 0.0 OK OK
B7 24 A325M - 1 LE2 9.6 83.3 290.4 4.5 66.1 0.0 OK OK
B8 24 A325M - 1 LE2 7.2 76.8 290.4 3.4 60.9 0.0 OK OK
B9 24 A325M - 1 LE2 16.8 73.3 290.4 8.0 58.1 0.0 OK OK
B10 24 A325M - 1 LE2 10.8 90.8 290.4 5.1 72.0 0.0 OK OK
B11 24 A325M - 1 LE2 7.6 77.2 290.4 3.6 61.2 0.0 OK OK
B12 24 A325M - 1 LE2 17.4 75.5 290.4 8.3 59.8 0.0 OK OK
B13 24 A325M - 1 LE2 3.6 100.8 290.4 1.7 79.9 0.0 OK OK
B14 24 A325M - 1 LE2 4.9 84.9 290.4 2.3 67.3 0.0 OK OK
B15 24 A325M - 1 LE2 18.6 79.4 290.4 8.8 62.9 0.0 OK OK
B16 24 A325M - 1 LE2 10.2 96.8 290.4 4.8 76.8 0.0 OK OK
B17 24 A325M - 1 LE2 2.0 85.1 290.4 0.9 67.5 0.0 OK OK
B18 24 A325M - 1 LE2 20.5 79.8 285.5 9.8 63.3 0.0 OK OK

B19 24 A325M - 1 LE2 2.8 40.0 250.7 1.3 31.7 0.0 OK OK

B20 24 A325M - 1 LE2 1.0 15.8 290.4 0.5 12.5 0.0 OK OK

B21 24 A325M - 1 LE2 5.5 24.4 290.4 2.6 19.3 0.0 OK OK

B22 24 A325M - 1 LE2 17.1 33.5 290.4 8.1 26.5 0.0 OK OK

B23 24 A325M - 1 LE2 4.3 15.0 290.4 2.1 11.9 0.0 OK OK

B24 24 A325M - 1 LE2 2.1 17.8 290.4 1.0 14.1 0.0 OK OK

B25 24 A325M - 1 LE2 14.5 36.4 224.0 6.9 28.8 0.0 OK OK

B26 24 A325M - 1 LE2 2.7 3.1 290.4 1.3 2.4 0.0 OK OK
B27 24 A325M - 1 LE2 1.8 19.6 222.7 0.9 15.5 0.0 OK OK
B28 24 A325M - 1 LE2 11.0 27.5 221.1 5.2 21.8 0.0 OK OK
B29 24 A325M - 1 LE2 1.3 4.9 290.4 0.6 3.9 0.0 OK OK
B30 24 A325M - 1 LE2 3.3 13.0 242.0 1.5 10.3 0.0 OK OK

B31 24 A325M - 1 LE2 26.8 82.1 290.4 12.7 65.1 0.0 OK OK

B32 24 A325M - 1 LE2 2.4 71.2 290.4 1.1 56.5 0.0 OK OK

B33 24 A325M - 1 LE2 3.1 66.9 287.4 1.5 53.1 0.0 OK OK

6 / 23
 Project:
Project no:
Author:

Ft V ϕRn,bearing Utt Uts Utts

Shape Item Grade Loads Detailing Status
[kN] [kN] [kN] [%] [%] [%]

B34 24 A325M - 1 LE2 13.0 86.9 290.4 6.2 68.9 0.0 OK OK

B35 24 A325M - 1 LE2 2.3 70.8 290.4 1.1 56.1 0.0 OK OK

B36 24 A325M - 1 LE2 3.6 67.2 290.4 1.7 53.3 0.0 OK OK

Design data
ϕRn,tension ϕRn,shear
Grade
[kN] [kN]
24 A325M - 1 210.2 126.1

Symbol explanation
Ft Tension force
V Resultant of bolt shear forces Vy and Vz in shear planes
ϕRn,bearing Bolt bearing resistance
Utt Utilization in tension
Uts Utilization in shear
Utts Utilization in tension and shear
ϕRn,tension Bolt tension resistance - AISC 360-22 – J3.7
ϕRn,shear Bolt shear resistance - AISC 360-22 – J3.7

Detailed result for B13

Tension resistance check (AISC 360-22 – J3-1)

ϕRn = ϕ ⋅ Fnt ⋅ Ab =
​ ​ ​
210.2 kN ≥ Ft = ​
3.6 kN

Where:
Fnt = 620.0 MPa – nominal tensile stress AISC 360-22 – Table J3.2
​

Ab = 452 mm2
​ – gross bolt cross-sectional area

ϕ = 0.75 – resistance factor

Shear resistance check (AISC 360-22 – J3-1)

ϕRn = ϕ ⋅ Fnv ⋅ Ab =
​ ​ ​
126.1 kN ≥ V = 100.8 kN

Where:
Fnv = 372.0 MPa – nominal shear stress AISC 360-22 – Table J3.2
​

Ab = 452 mm2
​ – gross bolt cross-sectional area

ϕ = 0.75 – resistance factor

7 / 23
 Project:
Project no:
Author:

Bearing resistance check (AISC 360-22 – J3-6)

Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu
​ ​
≤ 2.40 ⋅ d ⋅ t ⋅ Fu ​

ϕRn = ​
290.4 kN ≥ V = 100.8 kN

Where:
lc = 137 mm
​
– clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 15 mm – thickness of the plate
d = 24 mm – diameter of a bolt
Fu = 448.2 MPa – specified minimum tensile strength of the connected material
​

ϕ = 0.75 – resistance factor for bearing at bolt holes

Interaction of tension and shear check (AISC 360-22 – J3-2)

The required stress, in either shear or tension, is less than or equal to 30% of the corresponding available stress and the effects of

combined stresses need not to be investigated.

8 / 23
Project:
Project no:
Author:

Welds
tw w L Lc Fn ϕRn Ut Utc
Item Edge Xu Loads Detailing Status
[mm] [mm] [mm] [mm] [kN] [kN] [%] [%]
B1-w 1 SP1 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 157.0 196.3 80.0 70.1 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 159.3 198.1 80.4 71.9 OK OK
B1-w 1 SP2 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 157.1 197.5 79.5 65.4 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 154.7 195.4 79.2 64.1 OK OK
B2-w 1 SP3 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 165.5 200.5 82.5 76.6 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 164.9 200.2 82.4 75.8 OK OK
B2-w 1 SP4 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 174.8 200.9 87.0 83.1 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 175.8 201.2 87.4 86.0 OK OK
B1-tfl 1 SP9 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 44.5 200.6 22.2 10.7 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 26.5 181.7 14.6 5.9 OK OK
B1-tfl 1 SP10 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 124.6 166.1 75.1 45.5 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 158.6 205.8 77.1 57.4 OK OK
B1-bfl 1 SP11 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 156.1 205.2 76.1 56.4 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 109.4 172.6 63.4 42.3 OK OK
B1-bfl 1 SP12 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 19.8 189.8 10.5 0.0 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 25.7 175.8 14.6 6.0 OK OK
B2-tfl 1 SP13 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 22.8 198.4 11.5 0.0 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 27.3 178.7 15.3 7.0 OK OK
B2-tfl 1 SP14 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 118.2 162.3 72.8 50.6 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 157.8 205.6 76.7 59.2 OK OK
B2-bfl 1 SP15 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 25.4 180.6 14.1 5.9 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 41.7 203.7 20.5 9.5 OK OK
B2-bfl 1 SP16 E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 154.1 203.9 75.6 54.1 OK OK
E70xx ◢ 5.7 ◣ ◢ 8.0 ◣ 450 112 LE2 89.8 170.0 52.9 28.0 OK OK

Design data
Fexx
Material
[MPa]
E70xx 482.6

Symbol explanation
tw Throat thickness of weld
w Leg size of weld
L Length of weld
Lc Length of weld critical element
Fn Force in weld critical element
ϕRn Weld resistance - AISC 360-22 – J2-4
Ut Utilization
Utc Weld capacity estimation
◢ Fillet weld
Fexx Ultimate strength as rated by electrode classification number

9 / 23
 Project:
Project no:
Author:

Detailed result for B2-w 1 / SP4

Weld resistance check (AISC 360-22 – J2-4)

ϕRn = ϕ ⋅ Fnw ⋅ Awe =

​ ​ ​
201.2 kN ≥ Fn =
​
175.8 kN

Where:
Fnw = 421.8 MPa – nominal stress of weld material:
​

Fnw = 0.6 ⋅ FEXX ⋅ (1 + 0.5 ⋅ sin1.5 θ) , where:

​ ​

FEXX = 482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
​

θ = 70.3° – angle of loading measured from the weld longitudinal axis

Awe = 636 mm2 – effective area of weld critical element

​

ϕ = 0.75 – resistance factor for welded connections

Buckling
Factor
Loads Shape
[-]
LE1 1 21.38
2 23.06
3 27.48
LE2 1 6.62
2 7.06
3 7.13

First buckling mode shape, LE2

10 / 23
Project:
Project no:
Author:

Bill of material

11 / 23
Project:
Project no:
Author:

Manufacturing operations
Plates Welds Length
Name Shape Nr. Bolts Nr.
[mm] [mm] [mm]

SP1 P15.0x450-250 (A572 Gr.50) 1 Double fillet: 8.0 450 24 A325M 3

SP2 P15.0x450-250 (A572 Gr.50) 1 Double fillet: 8.0 450 24 A325M 3

SP3 P15.0x450-250 (A572 Gr.50) 1 Double fillet: 8.0 450 24 A325M 3

SP4 P15.0x450-250 (A572 Gr.50) 1 Double fillet: 8.0 450 24 A325M 3

SP5 P15.0x100-1000 (A572 Gr.50) 1 24 A325M 6

SP6 P15.0x100-1000 (A572 Gr.50) 1 24 A325M 6

SP7 P15.0x100-1000 (A572 Gr.50) 1 24 A325M 6

SP8 P15.0x100-1000 (A572 Gr.50) 1 24 A325M 6

12 / 23
Project:
Project no:
Author:

Plates Welds Length

Name Shape Nr. Bolts Nr.
[mm] [mm] [mm]

SP9 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

SP10 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

SP11 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

SP12 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

SP13 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

SP14 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

SP15 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

SP16 P15.0x250-450 (A572 Gr.50) 1 24 A325M 3

13 / 23
Project:
Project no:
Author:

Plates Welds Length

Name Shape Nr. Bolts Nr.
[mm] [mm] [mm]

SP17 P15.0x1000-100 (A572 Gr.50) 1 24 A325M 6

SP18 P15.0x1000-100 (A572 Gr.50) 1 24 A325M 6

SP19 P15.0x1000-100 (A572 Gr.50) 1 24 A325M 6

SP20 P15.0x1000-100 (A572 Gr.50) 1 24 A325M 6

Symbol explanation
Fillet weld leg size of weld

Welds
Throat thickness Leg size Length
Type Material
[mm] [mm] [mm]
Double fillet E70xx 5.7 8.0 5400

Bolts
Grip length
Name Count
[mm]
24 A325M 45 12
24 A325M 30 24

Drawing

SP1

14 / 23
 Project:
Project no:
Author:

P15.0x250-450 (A572 Gr.50)

SP2

P15.0x250-450 (A572 Gr.50)

15 / 23
 Project:
Project no:
Author:

SP3

P15.0x250-450 (A572 Gr.50)

SP4

P15.0x250-450 (A572 Gr.50)

16 / 23
Project:
Project no:
Author:

SP5

P15.0x1000-100 (A572 Gr.50)

SP6

P15.0x1000-100 (A572 Gr.50)

SP7

P15.0x1000-100 (A572 Gr.50)

SP8

P15.0x1000-100 (A572 Gr.50)

17 / 23
 Project:
Project no:
Author:

SP9

P15.0x450-250 (A572 Gr.50)

18 / 23
 Project:
Project no:
Author:

SP10

P15.0x450-250 (A572 Gr.50)

SP11

P15.0x450-250 (A572 Gr.50)

19 / 23
 Project:
Project no:
Author:

SP12

P15.0x450-250 (A572 Gr.50)

SP13

P15.0x450-250 (A572 Gr.50)

20 / 23
 Project:
Project no:
Author:

SP14

P15.0x450-250 (A572 Gr.50)

SP15

P15.0x450-250 (A572 Gr.50)

21 / 23
 Project:
Project no:
Author:

SP16

P15.0x450-250 (A572 Gr.50)

SP17

P15.0x100-1000 (A572 Gr.50)

SP18

P15.0x100-1000 (A572 Gr.50)

22 / 23
Project:
Project no:
Author:

SP19

P15.0x100-1000 (A572 Gr.50)

SP20

P15.0x100-1000 (A572 Gr.50)

23 / 23