INSTRUCTION MANUAL
AIRBRUSH COMPRESSOR AS18-2
Thanks for purchasing our air compressor and please read this
instruction manual carefully and thoroughly before operating the air
compressor to receive optimum results.
、1. Features & Functions:
Features:
Air pressure gauge; Air filter; Pressure adjustable.
Piston type: Oil-free.
It can start with pressure, continuous working, powerful.
Thermally protected.
Low Noise: 62db.
Auto-start and auto-stop function.
2. Data Sheet:
Type: Single Cylinder Piston Compressor
Power: 1/6HP
Speed: 1450/1700 r.p.m
Air Flow: 20~23L/Min
Auto-stop at the 4 Bar(57Psi), and Auto re-start from the 3 Bar(43Psi)
Pressure adjust range: 0~4BAR
Suitable for airbrush with nozzle size: 0.2~1.0MM
Net Weight: 3.6KG
Dimension: 275×140×220mm
2
3. Operation directory:
1. Usually the outlet thread size of our air compressor is 1/8’’ BSP. If you need the 1/4’’ BSP or
other NPT screw thread, you may get the other adapters to fix the outlet, then you can
connect with different air hoses.
2. The original air hose have rubber airproof inside; the user can make the airtight by hand, and
get good performance. If the air hose is not the original, usually the air hose and air
compressor cannot be well airproof. However, 100% airtight is only effective for auto stop
function air compressor. Seal thread tape can be used to prevent leakage. This elastic tape is
available in all stores selling sanitary products.
3. Connect the air compressor, air hose and airbrush (or other air tools), plug into the mains
supply, turn on the switch, then the air compressor will start work. The press gauge will show
the max pressure, and you can adjust the working pressure by adjusting the pressure adjustor.
4. Checking the air leakage. Please do not use any air tools before the compressor reach the
maximum pressure and observe whether it will be auto-stop. If the compressor will not be
auto-stop, please turn off the switch, then check the index on pressure gauge, if it is very
steady, means the airtight is very good; While the index decline down quickly, it means there
has the air leakage in the area of the connection. Please check and make it airtight, because
any small leakage will affect the performance of the compressor. (It may lead to frequently
auto-stop and auto-start).
5. The difference between maximum pressure and working pressure. The compressor’s
maximum pressure is the highest pressure it can build up, and the working pressure is the
one shown on the pressure gauge When the connected airbrush is opened. Apparently, the
working pressure is the constant pressure the compressor can maintain during airbrushing.
The level of this working pressure depends on the nozzle diameter of the airbrush to which it
is connected; the larger the nozzle diameter, the bigger the amount of air which can escape
and the lower the compressor’s working pressure.
6. The bottom of the regulator & filter is the water release valve, and users can open the valve
to release the water or moisture at any time.
3
4. Notice:
1. The users should choose the right air compressor with suitable air flow and pressure
according to the actual work requirement.
2. Before connecting the compressor, check the main voltage compatible with the electrical
characteristics of the motor.
3. Please follow local electrical rules, and safety rules. And use the socket which must be
earthing.
4. Never leave the appliance exposed to dust, acids, vapors, explosive or flammable gasses or
atmospheric agents (rain, sun, fog, snow).
5. The vacuum pump must be used in suitable environments (well-ventilated, with an ambient
temperature between +5℃ and +40℃)
6. Never use the appliance in your bare feet or wet feet, as well as the wet hand.
7. Never allow the children to touch the working machine or insert the stick into the machine. It
will cause the danger of scald or get an electric shock.
8. Do not open or tamper with any part of the compressor. Contact an authorized Service
Center.
4
5. Operation of Regulator & Filter
Pressure regulator
Pressure Gauge
Water Release Valve
Type: AFR-2000
Characteristic:
The AFR-2000 is an in-line low pressure regulator with a 100 P.S.I gauge and moisture trap. This
regulator gives user control of operating pressure as well as assisting in furnishing clean, dry and
regulated air. Regulators must only be used as instruction and warnings specify.
Operation:
1. The gauge reflect the working pressure of the air tools.
2. Pull the Pressure regulator up; turn clockwise to increase the pressure; turn counter-clockwise
to reduce the pressure.
3. Turn the pressure regulator to get the right working pressure needed, and fix it. Do not turn the
button when it can not be adjusted.
4. Pull the button water-release valve to release the water.
5
6. SPARE PART LIST:
6
7、Air compressor structure
a.Power plug
b.Power switch
c.Handle
d.Pressure regulator
e.Pressure gauge
f.Connection
g.Air filter
