Scribd
Upload
44 views

PI Controller Wiring BMS

The document provides detailed wiring configurations for the Burger Tuning JB4 Port Injection Controller across various platforms including N54, N55, and S55. It outlines the color-coded wires, their connections, and additional notes for proper setup. Key components include power, ground, RPM, TMAP, signal, and ethanol sensor connections with specific pin assignments on the JB4 connectors.

Uploaded by

Jakub Lamik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
44 views

PI Controller Wiring BMS

The document provides detailed wiring configurations for the Burger Tuning JB4 Port Injection Controller across various platforms including N54, N55, and S55. It outlines the color-coded wires, their connections, and additional notes for proper setup. Key components include power, ground, RPM, TMAP, signal, and ethanol sensor connections with specific pin assignments on the JB4 connectors.

Uploaded by

Jakub Lamik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Burger Tuning JB4 Port Injection Controller Wiring Configurations

Platform Wire Color Connects to… Additional notes


Power Red 12V switched Green connector in DME box, connect to either orange wire
Ground Black Chassis Shock tower
RPM Purple Pin 21 on JB4 gray connector As counted from the female connectror
N54 TMAP Yellow Pin 9 on JB4 DB9 connector JB4 USB cable or JB4 Mobile Connect Kit required
Signal White Pin 15 on JB4 DB25 connector Set Meth Scaling to 100. If occupied, remove meth kit.

E. Sensor White Pin 2 on JB4 DB25 connector Set FUA to 58, ethanol content reported as DutyC

E-Series
Wire Color Connects to… Additional notes
Power Red 12V switched Large red wire in black connector at back of DME box
Ground Black Chassis Shock tower
N55 RPM Purple Dark gray/black wire in DME box Find the small textured wire that extends through DME box
New PWM
chip
TMAP Yellow Pin 1 on JB4 DB25 connector
needed Signal White Pin 16 on JB4 DB25 connector Set Meth Scaling to 100. If occupied, remove meth kit.

E. Sensor White Pin 3 on JB4 DB25 connector Set FUA to 58, E content report as DutyC

Platform Wire Color Connects to… Additional notes


Power Red 12V Attaches to jump terminal with fuse assembly
N55 Ground Black Chassis Shock tower
RPM Purple Pin 3 of JB4 OBDII 4 pin connector Insert pin from purple extention wire in to slot below green wire
PWG
New PWM
TMAP Yellow Pin 1 on JB4 DB25 connector
chip Signal White Pin 16 on JB4 DB25 connector Set Meth Scaling to 100. If occupied, remove meth kit.
needed
E. Sensor White Pin 3 on JB4 DB25 connector Set FUA to 58, E content report as DutyC

Wire Color Connects to… Additional notes


Power Red 12V Attaches to jump terminal with fuse assembly
Ground Black Chassis Shock tower
N55 RPM Purple Pin 3 of JB4 OBDII 4 pin connector Insert pin from purple extention wire in to slot below green wire
F-Series TMAP Yellow Pin 1 on JB4 DB25 connector
EWG Signal White Pin 14 on JB4 DB25 connector Set Meth Scaling to 100. If occupied, remove meth kit.

E. Sensor White Pin 3 on JB4 DB25 connector Enable bit 3, E content report as DutyC

Wire Color Connects to… Additional notes


Power Red 12V Attaches to jump terminal with fuse assembly
Ground Black Chassis Shock tower
RPM Purple Pin 3 of JB4 OBDII 4 pin connector Insert pin from purple extention wire in to slot below green wire
S55 TMAP Yellow Pin 1 on JB4 DB25 connector
Signal White Pin 16 on JB4 DB25 connector Set Meth Scaling to 100. If occupied, remove meth kit.

E. Sensor White Pin 3 on JB4 DB25 connector Enable bit 3, E content report as DutyC

You might also like