L2+ Managed PoE Switch
GS-5220 PoE Series
Quick Installation Guide
Table of Contents
1. Package Contents........................................................................................ 3
2. Requirements.............................................................................................. 5
3. Terminal Setup............................................................................................ 6
4. Logon to Console......................................................................................... 7
5. Configuring IP Address................................................................................. 8
6. Starting Web Management..........................................................................10
7. Saving Configuration...................................................................................13
8. Recovering Back to Default Configuration......................................................14
9. Customer Support......................................................................................15
1. Package Contents
Thank you for purchasing PLANET GS-5220 Series Managed PoE Switch. The
description of this model is shown below:
Gigabit 10G PoE System
Gigabit SFP
Model Name RJ45 SFP+ Power Redundant
Slots
Ports Slots Budget Power
GS-5220-24P4X 24 4 combo 4 400W -
GS-5220-24P4XR 24 4 combo 4 400W Yes
GS-5220-24PL4X 24 4 combo 4 600W -
GS-5220-24PL4XR 24 4 combo 4 600W Yes
GS-5220-48P4X 48 - 4 400W -
GS-5220-48P4XR 48 - 4 400W Yes
GS-5220-48PL4X 48 - 4 600W -
GS-5220-48PL4XR 48 - 4 600W Yes
“Managed PoE Switch” is used as an alternative name in this Quick Installation
Guide.
3
Open the box of the Managed Switch and carefully unpack it. The box should
contain the following items:
zz The Managed PoE Switch
zz Quick Installation Guide
zz RJ45 to RS232 Cable
zz Rubber Feet
zz Two Rack-mounting Brackets with Attachment Screws
zz Power Cord
zz SFP Dust-proof Caps
Model SFP Dust-proof Caps
GS-5220-24P4X 8
GS-5220-24P4XR 8
GS-5220-24PL4X 8
GS-5220-24PL4XR 8
GS-5220-48P4X 4
GS-5220-48P4XR 4
GS-5220-48PL4X 4
GS-5220-48PL4XR 4
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
zz Workstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with TCP/IP protocols.
zz Workstations are installed with Ethernet NIC (Network Interface Card)
zz Serial Port Connection (Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such as
Hyper Terminal included in Windows XP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
end to the console port of the Managed PoE Switch.
zz Ethernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45 connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
Note and then try it again.
5
3. Terminal Setup
To configure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type of serial port of the Managed Switch.
PC / Workstation
with
Terminal Emulation Software
Managed Switch
RS232 to RJ45 Cable
Serial Port RJ45
Console Port
Figure 3-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2. When the following screen appears, make sure that the COM port should be
configured as:
Baud: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Figure 3-2 COM Port Configuration
6
4. Logon to Console
Once the terminal is connected to the device, power on the Managed Switch, and
the terminal will display “running testing procedures”. Then, the following message
asks to log in user name and password. The factory default user name and
password are shown as follows and the login screen in Figure 4-1 appears.
Username: admin
Password: admin
Figure 4-1: Managed PoE Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
description of the commands, please refer to the following chapters.
1. For security reason, please change and memorize the new pass-
word after this first setup.
2. Only accept command in lowercase letter under console inter-
Note face.
7
5. Configuring IP Address
The Managed PoE Switch is shipped with default IP address shown below.
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
use the procedures as follows:
Show the current IP Address
1. At the “#” prompt, enter “show ip interface brief”.
2. The screen displays the current IP address as shown in Figure 5-1.
Figure 5-1: IP Information Screen
Configuring IP Address
3. At the “#” prompt, enter the following command and press <Enter> as shown
in Figure 5-2.
GS-5220 Series# configure terminal
GS-5220 Series(config)# interface vlan 1
GS-5220 Series(config-if-vlan)# ip address 192.168.1.100 255.255.255.0
The previous command would apply the following settings for the Managed Switch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Figure 5-2: Configuring IP Address Screen
4. Repeat step 1 to check if the IP address has changed.
8
Store current switch configuration
5. At the “#” prompt, enter the following command and press <Enter>.
# copy running-config startup-config
Figure 5-3: Saving Current Configuration Command Screen
If the IP is successfully configured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the Managed
Switch through the new IP address.
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help descrip-
tion.
Note
9
6. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is configured through an Ethernet connection.
Please make sure the manager PC must be set to the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
then the manager PC should be set to 192.168.0.x (where x is a number
between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 6-1: IP Management Diagram
Logging in to the Managed Switch
1. Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100 (the factory default IP address or the one that you have
just changed in console) to access the Web interface.
2. When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screen in Figure 6-2 appears.
10
Default IP Address: 192.168.0.100
Default Username: admin
Default Password: admin
Figure 6-2: Login Screen
3. After entering the password, the main screen appears as Figure 6-3 shows.
Figure 6-3: Web Main Screen of Managed Switch
11
The Switch Menu on the left of the Web page lets you access all the commands
and statistics the Managed PoE Switch provides.
Figure 6-4: Switch Menu
If you are not familiar with Switch functions or the related param-
eter, press “Help icon” anytime on the Web page to get the help
description.
Note
Now, you can use the Web management interface to continue the Switch
management or manage the Switch by console interface.
Please refer to the user’s manual for more.
12
7. Saving Configuration
In the Managed Switch, the running configuration file stores in the RAM. In the
current version, the running configuration sequence of running-config can be saved
from the RAM to FLASH by executing save startup config command, so that the
running configuration sequence becomes the startup configuration file, which is
called configuration save.
To save all applied changes and set the current configuration as a startup
configuration, the startup-configuration file will be loaded automatically across a
system reboot.
1. Click System and then Save Startup Config.
2. Press the “Save Configuration” button.
13
8. Recovering Back to Default Configuration
IP address has been changed or admin password has been forgotten –
To reset the IP address to the default IP address “192.168.0.100” or reset the
login password to default value, press the hardware reset button on the rear
panel for about 10 seconds. After the device is rebooted, you can log in the
management Web interface within the same subnet of 192.168.0.xx.
2 4 6 8 10 12 14 16 18 20 22 24
PoE
DC
AC 1 3 5 7 9 11 13 15 17 19 21 23
RESET SYS 1000 LNK ACT at/af PoE In-use
10/100 LNK ACT
Figure 8-1: GS-5220-24P4X(R) Reset Button
14
9. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource and User’s Manual on PLANET Web site first to check if it could solve your
issue. If you need more support information, please contact PLANET switch support
team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[email protected]GS-5220 Series User’s Manual:
http://www.planet.com.tw/en/support/download.php?type1=1&model=&type=3
(Please select your switch model name from the drop-down menu of Product
Model.)
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their
respective owners.
15
