SAFETY DATA SEEET

1. Identification
Product identifier Spray Adhesive
Other means of identification
Product Code No. 03018 (Item# 1003268)
Recommended use General purpose aerosol adhesive
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Manufactured or sold by:
Company name CRC Industries, Inc.
Address 885 Louis Dr.
Warminster, PA 18974 US
Telephone
General Information 215-674-4300
Technical Assistance 800-521-3168
Customer Service 800-272-4620
24-Eour Emergency 800-424-9300 (US)
(CEEMTREC)
Website www.crcindustries.com

2. Eazard(s) identification
Physical hazards Flammable aerosols Category 1
Gases under pressure Liquefied gas
Eealth hazards Serious eye damage/eye irritation Category 2A
Reproductive toxicity Category 2
Specific target organ toxicity, single exposure Category 3 respiratory tract irritation
Specific target organ toxicity, single exposure Category 3 narcotic effects
Specific target organ toxicity, repeated Category 2
exposure
Environmental hazards Hazardous to the aquatic environment, acute Category 3
hazard
Hazardous to the aquatic environment, Category 3
long-term hazard
OSEA defined hazards Not classified.

Label elements

Signal word Danger

Eazard statement Extremely flammable aerosol. Contains gas under pressure; may explode if heated. Causes
serious eye irritation. May cause respiratory irritation. May cause drowsiness or dizziness.
Suspected of damaging fertility or the unborn child. May cause damage to organs through
prolonged or repeated exposure. Harmful to aquatic life. Harmful to aquatic life with long lasting
effects.

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 1 / 11
 Precautionary statement
Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not
spray on an open flame or other ignition source. Pressurized container: Do not pierce or burn,
even after use. Do not breathe mist or vapor. Do not apply while equipment is energized.
Extinguish all flames, pilot lights, and heaters. Vapors will accumulate readily and may ignite. Use
only with adequate ventilation; maintain ventilation during use and until all vapors are gone. Open
doors and windows or use other means to ensure a fresh air supply during use and while product
is drying. If you experience any symptoms listed on this label, increase ventilation or leave the
area. Wash thoroughly after handling. Wear protective gloves/protective clothing/eye
protection/face protection. Avoid release to the environment.
Response If inhaled: Remove person to fresh air and keep comfortable for breathing. Call a poison
center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get
medical advice/attention. If exposed or concerned: Get medical advice/attention.
Storage Store in a well-ventilated place. Store locked up. Protect from sunlight. Do not expose to
temperatures exceeding 50°C/122°F. Exposure to high temperature may cause can to burst.
Disposal Dispose of contents/container in accordance with local/regional/national regulations.
Eazard(s) not otherwise None known.
classified (ENOC)
Supplemental information None.

3. Composition/information on ingredients
Mixtures
Chemical name Common name and synonyms CAS number %
acetone 67-64-1 30 - 40
methyl acetate 79-20-9 10 - 20
petroleum distillates 8030-30-6 1 - 10
toluene 108-88-3 1 - 10
Specific chemical identity and/or percentage of composition has been withheld as a trade secret.

4. First-aid measures
Inhalation Move to fresh air. If breathing is difficult, give oxygen. Provide oxygen or artificial respiration if
needed. If person is not breathing, call 911 or an ambulance.
Skin contact Wash off immediately with soap and plenty of water. Get medical attention if symptoms occur.
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Ingestion Do not induce vomiting. Call a physician or poison control center immediately. Never give anything
by mouth to a victim who is unconscious or is having convulsions. If vomiting occurs, keep head
low so that stomach content doesn't get into the lungs.
Most important May cause drowsiness and dizziness. Headache. Nausea, vomiting. Severe eye irritation.
symptoms/effects, acute and Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May cause
delayed respiratory irritation. Prolonged exposure may cause chronic effects.
Indication of immediate Provide general supportive measures and treat symptomatically. Keep victim under observation.
medical attention and special Symptoms may be delayed.
treatment needed
General information IF exposed or concerned: Get medical advice/attention. Ensure that medical personnel are aware
of the material(s) involved, and take precautions to protect themselves. Show this safety data
sheet to the doctor in attendance.

5. Fire-fighting measures
Suitable extinguishing media Water fog. Dry chemicals. Foam. Carbon dioxide (CO2).
Unsuitable extinguishing Do not use a solid water stream as it may scatter and spread fire.
media
Specific hazards arising from Contents under pressure. Pressurized container may rupture when exposed to heat or flame.
the chemical During fire, gases hazardous to health may be formed.
Special protective equipment As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH
and precautions for firefighters (approved or equivalent) and full protective gear.

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 2 / 11
Fire-fighting In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without
equipment/instructions risk. Containers should be cooled with water to prevent vapor pressure build up. Use standard
firefighting procedures and consider the hazards of other involved materials. In the event of fire
and/or explosion do not breathe fumes.
General fire hazards Extremely flammable aerosol. Contents under pressure. Pressurized container may rupture when
exposed to heat or flame.

6. Accidental release measures

Personal precautions, Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
protective equipment and low areas. Many gases are heavier than air and will spread along ground and collect in low or
emergency procedures confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing
during clean-up. Do not breathe mist or vapor. Emergency personnel need self-contained
breathing equipment. Do not touch damaged containers or spilled material unless wearing
appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities
should be advised if significant spillages cannot be contained. For personal protection, see section
8 of the SDS.
Methods and materials for Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep
containment and cleaning up combustibles (wood, paper, oil, etc.) away from spilled material. Prevent product from entering
drains. Stop the flow of material, if this is without risk. Wipe up with absorbent material (e.g. cloth,
fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see
section 13 of the SDS.
Environmental precautions Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all
environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into
drains, water courses or onto the ground.

7. Eandling and storage

Precautions for safe handling Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spray
button is missing or defective. Do not spray on a naked flame or any other incandescent material.
Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill,
grind, or expose containers to heat, flame, sparks, or other sources of ignition. Use caution around
energized equipment. The metal container will conduct electricity if it contacts a live source. This
may result in injury to the user from electrical shock and/or flash fire. Avoid contact with eyes.
Avoid prolonged exposure. Pregnant or breastfeeding women must not handle this product.
Should be handled in closed systems, if possible. Use only in well-ventilated areas. Wear
appropriate personal protective equipment. Avoid release to the environment. Observe good
industrial hygiene practices. For product usage instructions, see the product label.
Conditions for safe storage, Level 3 Aerosol.
including any incompatibilities
Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50
°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat
or other sources of ignition. This material can accumulate static charge which may cause spark
and become an ignition source. Store in tightly closed container. Store in a well-ventilated place.
Stored containers should be periodically checked for general condition and leakage. Store away
from incompatible materials (see Section 10 of the SDS).

8. Exposure controls/personal protection

Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
US. OSEA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components Type Value
acetone (CAS 67-64-1) PEL 2400 mg/m3
1000 ppm
methyl acetate (CAS PEL 610 mg/m3
79-20-9)
200 ppm
petroleum distillates (CAS PEL 400 mg/m3
8030-30-6)
100 ppm

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 3 / 11
 US. OSEA Table Z-2 (29 CFR 1910.1000)
Components Type Value
toluene (CAS 108-88-3) Ceiling 300 ppm
TWA 200 ppm

US. ACGIE Threshold Limit Values

Components Type Value
acetone (CAS 67-64-1) STEL 500 ppm
TWA 250 ppm
methyl acetate (CAS STEL 250 ppm
79-20-9)
TWA 200 ppm
toluene (CAS 108-88-3) TWA 20 ppm

US. NIOSE: Pocket Guide to Chemical Eazards

Components Type Value
acetone (CAS 67-64-1) TWA 590 mg/m3
250 ppm
methyl acetate (CAS STEL 760 mg/m3
79-20-9)
250 ppm
TWA 610 mg/m3
200 ppm
petroleum distillates (CAS TWA 400 mg/m3
8030-30-6)
100 ppm
toluene (CAS 108-88-3) STEL 560 mg/m3
150 ppm
TWA 375 mg/m3
100 ppm

Biological limit values

ACGIE Biological Exposure Indices
Components Value Determinant Specimen Sampling Time
acetone (CAS 67-64-1) 25 mg/l Acetone Urine *
toluene (CAS 108-88-3) 0.3 mg/g o-Cresol, with Creatinine in *
hydrolysis urine
0.03 mg/l Toluene Urine *
0.02 mg/l Toluene Blood *
* - For sampling details, please see the source document.
Exposure guidelines
US - California OELs: Skin designation
toluene (CAS 108-88-3) Can be absorbed through the skin.
US - Minnesota Eaz Subs: Skin designation applies
toluene (CAS 108-88-3) Skin designation applies.
Appropriate engineering Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
controls should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level. Provide
eyewash station.
Individual protection measures, such as personal protective equipment
Eye/face protection Wear safety glasses with side shields (or goggles).

Skin protection
Eand protection Wear protective gloves such as: Laminate film.

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 4 / 11
 Other Wear suitable protective clothing.
Respiratory protection If engineering controls are not feasible or if exposure exceeds the applicable exposure limits, use a
NIOSH-approved cartridge respirator with an organic vapor cartridge. Use a self-contained
breathing apparatus in confined spaces and for emergencies. Air monitoring is needed to
determine actual employee exposure levels.
Thermal hazards Wear appropriate thermal protective clothing, when necessary.

General hygiene Observe any medical surveillance requirements. When using do not smoke. Always observe good
considerations personal hygiene measures, such as washing after handling the material and before eating,
drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove
contaminants.

9. Physical and chemical properties

Appearance
Physical state Liquid.
Form Aerosol.
Color Beige.
Odor Solvent.
Odor threshold Not available.
pE Not available.
Melting point/freezing point -144.4 °F (-98 °C) estimated
Initial boiling point and boiling 95 °F (35 °C) estimated
range
Flash point -4 °F (-20 °C) estimated
Evaporation rate Not available.
Flammability (solid, gas) Not available.
Upper/lower flammability or explosive limits
Flammability limit - lower 1.3 % estimated
(%)
Flammability limit - upper 16 % estimated
(%)
Vapor pressure 1689.6 hPa estimated
Vapor density Not available.
Relative density 0.76
Solubility(ies)
Solubility (water) Insoluble.
Partition coefficient Not available.
(n-octanol/water)
Auto-ignition temperature 550 °F (287.8 °C) estimated
Decomposition temperature Not available.
Viscosity Not available.
Percent volatile 72.5 % estimated

10. Stability and reactivity

Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability Material is stable under normal conditions.
Possibility of hazardous No dangerous reaction known under conditions of normal use.
reactions
Conditions to avoid Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Contact with
incompatible materials.
Incompatible materials Strong oxidizing agents. Strong acids. Strong alkalis.
Eazardous decomposition Carbon oxides. Hydrocarbons. Fumes.
products

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 5 / 11
11. Toxicological information
Information on likely routes of exposure
Inhalation May cause drowsiness and dizziness. Headache. Nausea, vomiting. May cause irritation to the
respiratory system. Prolonged inhalation may be harmful.
Skin contact No adverse effects due to skin contact are expected.
Eye contact Causes serious eye irritation.
Ingestion May be harmful if swallowed and enters airways.
Symptoms related to the May cause drowsiness and dizziness. Headache. Nausea, vomiting. Severe eye irritation.
physical, chemical and Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May cause
toxicological characteristics respiratory irritation.
Information on toxicological effects
Acute toxicity Not known.
Product Species Test Results
Spray Adhesive
Acute
Dermal
LD50 Rabbit 10880 mg/kg
Components Species Test Results
acetone (CAS 67-64-1)
Acute
Dermal
LD50 Rabbit > 15800 mg/kg
20000 mg/kg
Inhalation
LC50 Rat 76 mg/l, 4 Hours
Oral
LD50 Rat 5800 mg/kg
methyl acetate (CAS 79-20-9)
Acute
Oral
LD50 Rabbit 3.7 g/kg
petroleum distillates (CAS 8030-30-6)
Acute
Inhalation
LC50 Rat 61 mg/l, 4 Hours
toluene (CAS 108-88-3)
Acute
Dermal
LD50 Rabbit > 5000 mg/kg
Inhalation
LC50 Rat 12.5 mg/l, 4 hours
Oral
LD50 Rat 5580 mg/kg
Skin corrosion/irritation Prolonged skin contact may cause temporary irritation.
Serious eye damage/eye Causes serious eye irritation.
irritation
Respiratory or skin sensitization
Respiratory sensitization Not a respiratory sensitizer.
Skin sensitization This product is not expected to cause skin sensitization.
Germ cell mutagenicity No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 6 / 11
Carcinogenicity Not classifiable as to carcinogenicity to humans.
IARC Monographs. Overall Evaluation of Carcinogenicity
toluene (CAS 108-88-3) 3 Not classifiable as to carcinogenicity to humans.
OSEA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not regulated.
US. National Toxicology Program (NTP) Report on Carcinogens
Not listed.
Reproductive toxicity Suspected of damaging fertility or the unborn child.
Specific target organ toxicity - May cause respiratory irritation. May cause drowsiness and dizziness.
single exposure
Specific target organ toxicity - May cause damage to organs through prolonged or repeated exposure.
repeated exposure
Aspiration hazard Based on available data, the classification criteria are not met.
Chronic effects May cause damage to organs through prolonged or repeated exposure. Prolonged inhalation may
be harmful.

12. Ecological information

Ecotoxicity Harmful to aquatic life with long lasting effects.
Product Species Test Results
Spray Adhesive
Aquatic
Fish LC50 Fish 154.3469 mg/l, 96 hours estimated
Components Species Test Results
methyl acetate (CAS 79-20-9)
Aquatic
Fish LC50 Fathead minnow (Pimephales promelas) 295 - 348 mg/l, 96 hours
petroleum distillates (CAS 8030-30-6)
Aquatic
Crustacea EC50 Water flea (Daphnia pulex) 2.7 - 5.1 mg/l, 48 hours
Fish LC50 Rainbow trout,donaldson trout 8.8 mg/l, 96 hours
(Oncorhynchus mykiss)
8.8 mg/l, 96 hours
toluene (CAS 108-88-3)
Acute
Other EC50 Pseudokirchnerella subcapitata 433 mg/l, 96 hours
12.5 mg/l, 72 hours
Aquatic
Acute
Fish LC50 Coho salmon,silver salmon 5.5 mg/l, 96 hours
(Oncorhynchus kisutch)
Persistence and degradability No data is available on the degradability of any ingredients in the mixture.
Bioaccumulative potential
Partition coefficient n-octanol / water (log Kow)
acetone -0.24
methyl acetate 0.18
toluene 2.73
Bioconcentration factor (BCF)
toluene 90
Mobility in soil No data available.
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 7 / 11
13. Disposal considerations
Disposal instructions This material and its container must be disposed of as hazardous waste. Collect and reclaim or
dispose in sealed containers at licensed waste disposal site. Contents under pressure. Do not
puncture, incinerate or crush. Do not allow this material to drain into sewers/water supplies. Do not
contaminate ponds, waterways or ditches with chemical or used container. Dispose in accordance
with all applicable regulations.
Eazardous waste code D001: Waste Flammable material with a flash point <140 F
F003: Waste Non-halogenated Solvent - Spent Non-halogenated Solvent
Contaminated packaging Since emptied containers may retain product residue, follow label warnings even after container is
emptied. Empty containers should be taken to an approved waste handling site for recycling or
disposal.

14. Transport information

DOT
UN number UN1950
UN proper shipping name Aerosols, flammable, Limited Quantity
Transport hazard class(es)
Class 2.1
Subsidiary risk -
Label(s) 2.1
Packing group Not applicable.
Special precautions for user Read safety instructions, SDS and emergency procedures before handling.
Special provisions N82
Packaging exceptions 306
Packaging non bulk None
Packaging bulk None
IATA
UN number UN1950
UN proper shipping name Aerosols, flammable, Limited Quantity
Transport hazard class(es)
Class 2.1
Subsidiary risk -
Packing group Not applicable.
ERG Code 10L
Special precautions for user Read safety instructions, SDS and emergency procedures before handling.
Other information
Passenger and cargo Allowed with restrictions.
aircraft
Cargo aircraft only Allowed with restrictions.
IMDG
UN number UN1950
UN proper shipping name AEROSOLS, Limited Quantity
Transport hazard class(es)
Class 2.1
Subsidiary risk -
Packing group Not applicable.
Environmental hazards
Marine pollutant No.
EmS Not available.
Special precautions for user Read safety instructions, SDS and emergency procedures before handling.
DOT; IMDG

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 8 / 11
IATA

15. Regulatory information

US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
SARA 304 Emergency release notification
Not regulated.
OSEA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not regulated.
US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance
toluene (CAS 108-88-3)
CERCLA Eazardous Substance List (40 CFR 302.4)
acetone (CAS 67-64-1) Listed.
methyl acetate (CAS 79-20-9) Listed.
petroleum distillates (CAS 8030-30-6) Listed.
toluene (CAS 108-88-3) Listed.
CERCLA Eazardous Substances: Reportable quantity
acetone (CAS 67-64-1) 5000 LBS
methyl acetate (CAS 79-20-9) 100 LBS
petroleum distillates (CAS 8030-30-6) 100 LBS
toluene (CAS 108-88-3) 1000 LBS
Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National
Response Center (800-424-8802) and to your Local Emergency Planning Committee.
Other federal regulations
Clean Air Act (CAA) Section 112 Eazardous Air Pollutants (EAPs) List
toluene (CAS 108-88-3)
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act Not regulated.
(SDWA)
Drug Enforcement Administration (DEA). List 2, Essential Chemicals (21 CFR 1310.02(b) and 1310.04(f)(2) and
Chemical Code Number
acetone (CAS 67-64-1) 6532
toluene (CAS 108-88-3) 6594
Drug Enforcement Administration (DEA). List 1 & 2 Exempt Chemical Mixtures (21 CFR 1310.12(c))
acetone (CAS 67-64-1) 35 %WV
toluene (CAS 108-88-3) 35 %WV
DEA Exempt Chemical Mixtures Code Number
acetone (CAS 67-64-1) 6532
toluene (CAS 108-88-3) 594
FEMA Priority Substances Respiratory Eealth and Safety in the Flavor Manufacturing Workplace
acetone (CAS 67-64-1) Low priority
methyl acetate (CAS 79-20-9) Low priority
Food and Drug Not regulated.
Administration (FDA)

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 9 / 11
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Classified hazard Flammable (gases, aerosols, liquids, or solids)
categories Gas under pressure
Acute toxicity (any route of exposure)
Serious eye damage or eye irritation
Reproductive toxicity
Specific target organ toxicity (single or repeated exposure)
SARA 302 Extremely hazardous substance
Not listed.
SARA 313 (TRI reporting)
Chemical name CAS number % by wt.
toluene 108-88-3 1 - 10
US state regulations
US. New Jersey Worker and Community Right-to-Know Act
acetone (CAS 67-64-1)
methyl acetate (CAS 79-20-9)
petroleum distillates (CAS 8030-30-6)
toluene (CAS 108-88-3)
US. Massachusetts RTK - Substance List
acetone (CAS 67-64-1)
methyl acetate (CAS 79-20-9)
petroleum distillates (CAS 8030-30-6)
toluene (CAS 108-88-3)
US. Pennsylvania Worker and Community Right-to-Know Law
acetone (CAS 67-64-1)
methyl acetate (CAS 79-20-9)
petroleum distillates (CAS 8030-30-6)
toluene (CAS 108-88-3)
US. Rhode Island RTK
acetone (CAS 67-64-1)
methyl acetate (CAS 79-20-9)
petroleum distillates (CAS 8030-30-6)
toluene (CAS 108-88-3)
California Proposition 65
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

California Proposition 65 - CRT: Listed date/Carcinogenic substance

benzene (CAS 71-43-2) Listed: February 27, 1987
ethylbenzene (CAS 100-41-4) Listed: June 11, 2004
California Proposition 65 - CRT: Listed date/Developmental toxin
benzene (CAS 71-43-2) Listed: December 26, 1997
toluene (CAS 108-88-3) Listed: January 1, 1991
California Proposition 65 - CRT: Listed date/Male reproductive toxin
benzene (CAS 71-43-2) Listed: December 26, 1997
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3,
subd. (a))
acetone (CAS 67-64-1)
petroleum distillates (CAS 8030-30-6)
toluene (CAS 108-88-3)
Volatile organic compounds (VOC) regulations
EPA
VOC content (40 CFR 35.8 %
51.100(s))
Consumer products Not regulated
(40 CFR 59, Subpt. C)
State
Consumer products This product is regulated as a Web Spray Adhesive. This product is compliant for use in all 50
states.

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 10 / 11
 VOC content (CA) 35.8 %
VOC content (OTC) 35.8 %
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Australia Australian Inventory of Chemical Substances (AICS) No
Canada Domestic Substances List (DSL) No
Canada Non-Domestic Substances List (NDSL) No
China Inventory of Existing Chemical Substances in China (IECSC) No
Europe European Inventory of Existing Commercial Chemical No
Substances (EINECS)
Europe European List of Notified Chemical Substances (ELINCS) No
Japan Inventory of Existing and New Chemical Substances (ENCS) No
Korea Existing Chemicals List (ECL) No
New Zealand New Zealand Inventory No
Philippines Philippine Inventory of Chemicals and Chemical Substances No
(PICCS)
Taiwan Taiwan Chemical Substance Inventory (TCSI) No
United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).

16. Other information, including date of preparation or last revision

Issue date 08-25-2014
Revision date 08-29-2018
Prepared by Allison Yoon
Version # 04
Disclaimer The information contained in this document applies to this specific material as supplied. It may not
be valid for this material if it is used in combination with any other materials. This information is
accurate to the best of CRC's knowledge or obtained from sources believed by CRC to be
accurate. Before using any product, read all warnings and directions on the label. For further
clarification of any information contained on this (M)SDS consult your supervisor, a health & safety
professional, or CRC Industries, Inc..
Revision information This document has undergone significant changes and should be reviewed in its entirety.

Material name: Spray Adhesive SDS US

No. 03018 (Item# 1003268) Version #: 04 Revision date: 08-29-2018 Issue date: 08-25-2014 11 / 11