PI666000 Rev. 08.

13

SERVICE INSTRUCTIONS FOR THE RE [530 & 531] SERIES MOTORS

For Use With Seal Kits: 500444004 & 700666000

dimensions: mm [in]

Housing/shaft disassembly and assembly

NOTE - These instructions are intended to service all RE motors with 1.5” Bearings. However, there are slight differences in the
bearing/seal assemblies of these motors. It is important that you determine which motor type you have before servicing so that
o an n o he app op ia e se ion. he se ion hea in s lis ea h ho sin an e pe. he ho sin n e is he 7 h h
alpha-numeric digit in the model code, which is located on the tag on the rear of the motor. If the tag is missing, the exploded
views may be used to determine which housing type you have.

SECTION 1. “R” FLANGE MOTORS (ex. 530300R3131AAAAA)

A) Remove all shaft related components from shaft (26) (i.E. Keys, wire rings, nuts, etc.). Secure motor in vise by clamping onto
ho sin . e ove e ainin snap in o oove in pilo o ho sin 14 . i sha ea in asse l o ho sin 14 hen
remove bearing spacer (10), bearing (11), thrust bearing (13) and two thrust washers (12) from shaft (26).

B) Being careful not to drop any rolls from bearing (11), pry out shaft seal (5), backup seal (4), metal backup shim (3a), metal backup
ring (3) and dust seal (1) from bearing assembly (11). (Note: metal backup ring (3) may or may not come out of bearing (11). It is
not necessary to remove the metal backup ring (3) from the bearing (11) to service the motor.) Remove high pressure seal (2) from
groove in pilot of housing (14) discard shaft seal (5), backup seal (4) dust seal (1) and high pressure seal (2).

At this point, all parts should be cleaned in a oil-based solvent and dried using compressed air (for safety, observe all Osha Safety
Guidelines). All new seals should be lightly coated with clean oil prior to installation.

C) ns all hi h p ess e seal 2 in o oove in pilo o ho sin 14 . Pla e sha 26 on a lean, a s a e i h o p en a in p.

Place thrust washer (12), thrust bearing (13) and second thrust washer (12) over shaft (26). Being careful not to cut seal on key-
a , pla e sha seal 5 ove sha 26 akin s e ha lip on seal a es o n see e 1 . epea p o ess o a k p seal 4
making sure that lip faces down. Place metal backup shim (3a) over shaft. If metal backup ring (3) came out of bearing (11), place
ove sha 26 akin s e ha la e O. . si e a es o n. i h l ease ea in 11 i nee e . Pla e ea in 11 ove sha
making sure that the large O.D. side faces down. Using an arbor press, carefully press bearing (11) down to press seal assembly
(3-5) into bearing (11).

D) Pla e sha 26 asse l in o ho sin 14 . ns all s seal 1 ove sha 26 i h lip a in p see e 1 an a e ll p ess
the seal down to seat it in the bearing (11). Place bearing spacer (10) over shaft (26) and push down until snap ring groove is vis-
i le. ns all e ainin snap in in o oove in ho sin pilo 14 . o e: i a e ne essa o li h l ap he e ainin snap in
an ea in spa e 10 o allo he e ainin snap in o sea p ope l . epla e all sha ela e o ponen s i.e. ke s,
wire rings, nuts).

E) See section 4 for motor disassembly and assembly.

15
BACKUP BACKUP HOUSING
RING
27

12

4 26
3a
BACKUP 2
38 [1.50] BEARING SHIM H F
10 14
FIGURE 1
1
13
1. * Dust Seal 12. Thrust Washers (2)
5
2. * High Pressure Seal 13. Thrust Bearing
3. * Metal Backup Ring 14. Housing 3
3a. * Metal Backup Shim 15. Rear Housing Bearing
11
4. * Backup Seal 26. Shaft
5. * Shaft Seal 27 Shaft Key 9
. e ainin nap in 28. Shaft Nut
28
10. Bearing Spacer
11. 1.5" Bearing * Contained in Seal Kit 700666000

White Drive Products, Inc. • P.O. Box 2700 • Hopkinsville, KY 42241 • Phone: 270.885.1110 • Fax: 270.886.8462
 SECTION 2. “A” FLANGE MOTORS (ex. 530300A5130AAAAA)

A) Remove all shaft related components from shaft (26) (i.e. keys, wire rings, nuts, etc.). Secure motor in vise by clamping onto hous-
in . e ove e ainin snap in o oove in pilo o ho sin 14 . i sha ea in asse l o ho sin 14 hen e ove
bearing (10), seal carrier (11), thrust bearing (13) and two thrust washers (12) from shaft (26).

B) Using a small thin bladed screwdriver, pry out shaft seal (5), backup seal (4) and metal backup shim (3) from seal carrier (11).
Also pry dust seal (1) from bearing (10). Remove high pressure seal (2) from groove in pilot of housing (14) discard shaft seal (5),
backup seal (4), metal backup shim (3), dust seal (1) and high pressure seal (2).

At this point, all parts should be cleaned in a oil-based solvent and dried using compressed air (for safety, observe all Osha
Safety Guidelines). All new seal should be lightly coated with clean oil prior to installation.

C) ns all hi h p ess e seal 2 in o oove in pilo o ho sin 14 . Pla e sha on a lean, a s a e i h o p en a in p.

Place thrust washer (12), thrust bearing (13) and second thrust washer (12) over shaft (26). Being careful not to cut seal on key-
a , pla e sha seal 5 ove sha 26 akin s e ha lip on seal a es o n see e 2 . epea p o ess o a k p seal
4 akin s e ha lip a es o n. Pla e e al a k p shi ove sha 26 . i h a si e a in p, pla e seal a ie 11
down over shaft. Using an arbor press, carefully press down on seal carrier (11) to press seal assembly (3-5) into seal carrier (11).
i hl ease ea in 10 i nee e . Pla e ea in 10 ove sha akin s e ha si e o ea in i h snap in a ains ea -
ing rolls faces down.

D) Pla e sha 26 asse l in o ho sin 14 . ns all s seal 1 ove sha 26 i h lip a in p see e 2 an a e ll p ess
he seal o n o sea i in he ea in 10 . ns all e ainin snap in in o oove in ho sin pilo 14 . o e: a e ne es-
sa o li h l ap he e ainin snap in o allo i o sea p ope l . epla e all sha ela e o ponen s i.e. ke s, i e in s,
nuts).

E) See section 4 for motor disassembly and assembly.

DUST SEAL SEAL CARRIER BACKUP SEAL HOUSING

38 [1.50] BEARING METAL BACKUP SHIM SHAFT SEAL

FIGURE 2

1. * Dust Seal
2. * High Pressure Seal
3. * Metal Backup Ring
4. e on Ba k p eal
5. * Shaft Seal
. e ainin nap in
10. 1.5" Bearing
11. Seal Carrier
12. Thrust Washers (2)
13. Thrust Bearing
14. Housing
15. Rear Housing Bearing
26. Shaft
27. Shaft Key
28. Shaft Nut

* Contained in Seal Kit 700666000

White Drive Products, Inc. • P.O. Box 2700 • Hopkinsville, KY 42241 • Phone: 270.885.1110 • Fax: 270.886.8462
 SECTION 3. “W” FLANGE MOTORS (ex. 530750W3131AAAAA)

A) Remove all shaft related components from shaft (28) (i.e. keys, wire rings, nuts, etc.). Secure motor in vise by clamping onto hous-
in . sin a s all hin la e s e ive , p s seal 1 o ho sin 15 an is a . e ove e ainin in o oove in
pilo o ho sin 15 . i sha ea in asse l o ho sin 15 hen e ove seal a ie asse l 10 , ea in 11 , ea in
spacer (12), thrust bearing (14) and two thrust washers (13) from shaft (28).

B) Using a small thin bladed screwdriver, pry out shaft seal (5), backup seal (4) and metal backup shim (3) from seal carrier (10).
Remove high pressure seal (2) from groove in pilot of housing (15) discard shaft seal (5), backup seal (4), metal backup shim (3)
and high pressure seal (2).

At this point, all parts should be cleaned in a oil-based solvent and dried using compressed air (for safety, observe all Osha
Safety Guidelines). All new seal should be lightly coated with clean oil prior to installation.

C) ns all hi h p ess e seal 2 in o oove in pilo o ho sin 15 . Pla e sha on a lean, a s a e i h o p en a in p.

Place thrust washer (13), thrust bearing (14) and second thrust washer (13) over shaft (28). Place bearing spacer (12) over shaft
26 . Pla e seal a ie 10 on a lean a s a e i h he a si e a in o n. ns all e al a k p shi in o seal a ie
10 . akin s e ha lips on o h seals a e p see e , ins all a k p seal 4 in o seal a ie 10 ollo e sha seal
(5). Using an arbor press, carefully press down on shaft seal (5) to press seal assembly (3-5) into seal carrier (10). With shaft seal
(5) facing down, carefully lower seal carrier assembly down onto shaft making sure to not cut seal lip on keyway.

D) Pla e sha 28 asse l in o ho sin 15 . ns all e ainin snap in in o oove in ho sin pilo 15 . o e: i a e ne es-
sa o li h l ap he e ainin snap in o allo i o sea p ope l . epla e all sha ela e o ponen s i.e. ke s, i e
in s, n s . ns all s seal 1 ove sha 25 i h lip a in p see e an a e ll p ess he seal o n o sea i in he
housing (15).

E) See section 4 for motor disassembly and assembly.

DUST SEAL METAL BACKUP SHIM SHAFT SEAL HOUSING

SEAL CARRIER BACKUP SEAL 38 [1.50] BEARING

FIGURE 3

16
1. * Dust Seal
2. * High Pressure Seal
3. * Metal Backup Ring 29
4. * Backup Seal
5. * Shaft Seal
. e ainin nap in
10. Seal Carrier
11. 1.5" Bearing 17
12. Bearing Spacer 13
13. Thrust Washers (2)
28
14. Thrust Bearing 11
15. Housing 4
16. Rear Housing Bearing
10 15
17. Thrust Bearing
28. Shaft 9
2 . ha Ke
30. Shaft Nut 30
14
12
* Contained in Seal Kit 700666000
5
3

2
1

White Drive Products, Inc. • P.O. Box 2700 • Hopkinsville, KY 42241 • Phone: 270.885.1110 • Fax: 270.886.8462
 SECTION 4. MOTOR SECTION DISASSEMBLY & ASSEMBLY FOR “A”, “R”, & “W” FLANGE HOUSINGS

A) oosen an e ove seven ol s 1 hol in o o asse l o e he . e ove en ove 22 an o seal 8 . is a seal.

Remove balance plate (20) taking care not to drop the three steel balls (21) located in the three holes in the balance plate (20).
e ove o o asse l 1 , ani ol 17 , ive link spa e 18 no e: so e o o s o no se spa e , an ive link 16 . e-
ove o seals 7 o o o asse l 1 an ho sin seal 6 o ho sin an is a seals.

At this point, all parts should be cleaned in a oil-based solvent and dried using compressed air (for safety, observe all osha safety
guidelines). All new seal should be lightly coated with clean oil prior to installation.

B) If applicable, install thrust washer (17) onto end of shaft (Not shown in this Section. See the exploded view drawing in Section 3.
Not all 530 Series motors use this thrust washer). Place drive link (16) into shaft making sure that end of drive link with crowned
splines goes into shaft. Place manifold (17) onto housing aligning bolt holes. (Note: manifold side with only seven valving holes
goes toward housing.)

C) ns all a o seal 7 in o he seal oove in o h si es o o o asse l 1 . akin s e ha si e o o o 1 i h ha e in

splines a es o n, pla e o o asse l 1 on ani ol 17 en a in ive link splines. n o o asse l 1 o ali n ol
holes.

D) o o a e i h spa e 18 , pla e spa e on en o ive link 16 . Pla e alan e pla e 20 on o he o o asse l 1 ih

three holes for steel balls (21) facing up. Install three steel balls (21) into the holes in the balance plate (20).

E) Install endcover seal (8) into endcover (22). Place endcover (22) onto the balance plate (20) and align bolt holes. Insert seven
ol s 1 in o o o asse l . P e o e ol s o 1 ,6 10 . l . . sin he ol pa e n in Fi e 4 nal o e he ol s o
6 ,8 7,5 51.5 5.5 . l . .

1
4 6

5 3

8
2 7

FIGURE 4 20

19
31
18

22
17
21

16

6. * Rear Housing Seal

7. * Body Seals
8. * Endcover Seal
7 16. ive ink
17. Manifold
18. ive ink pa e
6 1 . o o sse l
20. Balance Plate
21. Steel Balls (3)
22. Endcover
31. Assembly Bolts (7)

* Contained in Seal Kit 700666000

White Drive Products, Inc. • P.O. Box 2700 • Hopkinsville, KY 42241 • Phone: 270.885.1110 • Fax: 270.886.8462
 SECTION 5. “T” FLANGE MOTORS (ex. 530540T3828AAAAA)

A) Remove all shaft related components from shaft (23) (i.e. keys, nuts). To aid in reassembly of the motor, make a "V" shaped set
of lines from the endcover (21) to the housing using either paint or a marker. With shaft facing down, secure motor in vise by
clamping on to housing (10).

B) oosen an e ove seven ol s 22 hol in o o asse l o e he . e ove en ove 21 an en ove seal 7 . is a

seal. e ove alan e pla e 1 akin a e no o op he h ee s eel alls 20 lo a e in he h ee holes in he alan e pla e
1 . e ove o o asse l 18 , ani ol 17 , ive link spa e 16 O : o e o o s o no se spa e , ive link 15
and thrust bearing (14). Remove body seals (6) from rotor assembly (18) and housing seal (2) from housing (10) and discard
seals.

C) Gently tap shaft (23) upward from housing (10) and remove through rear of housing and lay aside. Remove housing (10) from vise
and turn over. Pry dust seal (1) from housing and discard.

D) Using a slide and hammer bearing puller (see Figure 1) remove rear housing bearing (8) through rear of housing.

E) Remove the thrust washer (13), front thrust bearing (12), front thrust washer (11), shaft seal (5), back-up seal (4), back-up shim
(3a), and back-up ring (3) from housing. Discard items (3, 3a, 4, & 5).

At this point, all parts should be cleaned in an oil-base solvent and dried using compressed air (For safety, observe all OSHA
safety guidelines). All new seals should be lightly coated in clean oil prior to installation.

F) Pla e sha 2 on a lean a s a e i h o p en a in p. Pla e on sha , h s ashe 1 , hen h s ea in 12 ,

hen on h s ashe 11 . i h l oa seal a ea o sha i h lean oil an pla e sha seal 5 o n on o sha 2 akin
sure that lip on seal faces down (See Figure 2 for correct seal orientation) until it contacts thrust washer (11). Carefully install the
a k p seal 4 on o he sha 2 i h he a si e p an he seal lip a in he sha seal 5 . Pla e he e al a k p shi
a on o he sha , hen pla e he a k p in on o he sha i h he a si e a ains he a k p shi a.

G) Place housing (10) onto shaft assembly. Place housing shaft assembly back in vise with output shaft facing down. Install rear
ho sin ea in 8 in o ea o ho sin n il ea in 8 on a s he s op in he ho sin a si e o ea in 8 sho l a e p-
ward away from housing.

H) Install drive link (15) in shaft end (crowned splines goes into shaft end). Place thrust bearing (14) over drive link (15). If shaft as-
se l is p ope l sea e in ho sin 10 , h s ea in 14 ill e sh o o n e s nk i h ea s a e o ho sin 10 .

I) Install housing seal (2) into groove in housing (10). Place manifold (17) onto housing, (10) side with only seven holes facing
housing (10). Place body seals (6) in grooves in both sides of rotor (18). Place rotor (18) onto manifold (17) with side of rotor with
chamfer in splines facing manifold (17). If motor used a drive link spacer (16), place spacer (16) on top of drive link (15).

J) ns all alan e pla e 1 on o o o 18 akin s e holes o s eel alls 20 a es p. ns all h ee s eel alls 20 in holes in al-
an e pla e 1 . ns all en ove seal 7 in o oove in en ove 21 an pla e en ove on o alan e pla e 1 . ns all seven as-
se l ol s 22 an p e o e o 10 . l s. sin he ol o e se en e sho n in Fi e , nal o e all ol s o 50 . l s.

Remove motor from vise and place on work surface with shaft (23) facing up. Making sure that lip on seal (1) faces up, place dust
K) seal (1) over shaft (23). Using a sleeve and a hammer, carefully drive dust seal (1) into place.

BACK-UP SHIM SHAFT SEAL THRUST BEARING

1
4 6

5 3

BACKUP RING BACKUP SEAL THRUST WASHER THRUST WASHER 2 7

FIGURE 1 FIGURE 2 FIGURE 3

White Drive Products, Inc. • P.O. Box 2700 • Hopkinsville, KY 42241 • Phone: 270.885.1110 • Fax: 270.886.8462
SECTION 5. “T” FLANGE MOTORS - continued

1. * Dust Seal 22
2. * Housing Seal
3. * Back Up Ring
3a. * Back Up Shim
4. * Back Up Seal 7
5. * Shaft Seal
19
6. * Body Seals (2)
7. * Endcover Seal
8. * Rear Housing Bearing 18
. F on Ho sin Bea in
10. Housing
17
11. Front Thrust Washer
21
12. Front Thrust Bearing 15
13. Thrust Washer 20
14. Rear Thrust Bearing
15. ive ink
16. ive ink pa e
17. Manifold
18. Rotor Assembly 6 8
1 . Balan e Pla e
20. Steel Balls (3) 16
24
21. Endcover
22. Assembly Bolts (7)
12
23. Shaft
24. Shaft Key 5
25. Shaft Nut 3
14
* Contained in Seal Kit 500444004 9
23
10
1 13
11
4
3a
2

25

White Drive Products, Inc. • P.O. Box 2700 • Hopkinsville, KY 42241 • Phone: 270.885.1110 • Fax: 270.886.8462