Portable single gas detector

(gas detection alarm)

Operatiom manual
Content
1、Overview
2、Structure
3、Technology
4、Function and operational methods
5、Menu guide
6、Precautions for use
7、Common faults and their solutions
8、Store
9、Accessories and others
10、Schedule
1、Overview
This portable gas detector (hereinafter referred to as the
detector) adopts a state-of-the-art large-scale integrated
circuit technology, an international standard intelligent
technology in design and a proprietary digital analog hybrid
communication technology to design a full intelligent gas
detector.The detector makes use of natural diffusion to
detect gas. The sensitive components consists of
high-quality gas sensors that enjoys excellent sensitivity
and repeatability and is easy to use and maintain. It meets
the requirements of reliability for equipment in industrial
site safety monitoring to great extent. It is made from
high-strength engineering plastics with high strength, good
hand feeling, and waterproof, dustproof and
explosion-proof.
The detector is widely used in petroleum, chemical,
environmental protection, metallurgy, refining, gas
transmission and distribution, biochemical medicine,
agriculture and so on.
1.1 The design, manufacture and verification of this product
comply with the following national standards:
GB3836.1-2010 Explosive Environments Part 1: General
Requirements for Equipment
GB3836.4-2010 Explosive Environments Part 4: Equipment
Protected by "i" with Intrinsically Safe
GB15322.3-2003 Portable flammable gas detectors Part 3:
Portable flammable gas detectors with a measuring range of
(0 to 100) % LEL
JJG693-2011 Testing procedures for flammable gas detection
alarms
JJG365-2008 Testing procedures for electrochemical oxygen
detection
JJG695-2003 Testing procedures for hydrogen sulfide gas
detection
JJG915-2008 Testing procedures for carbon monoxide
detection alarms

2, structure and working principle

2.1 Table of structure

1、2、3 Alarm indicator window 7 Gas sensing hole

4 Left key 8 charging port
5 Middle key 9 LCD screen
6 Right key
2.2 Detector is composed of housing, circuit board, battery,
display, sensor, charger, etc.
2.3 Working principle: electrochemical and catalytic
combustion
3. Technology
The detection range of the conventional gas:
Gas High
Range Low alarm Resolution
detection alarm
Oxygen 0-30%VOL 19.5 23.5 0.1%VOL
Flammable
0-100%LEL 20 50 1%LEL
gas
Carbon
0-1000PPM 50 150 1PPM
monoxide
Hydrogen
0-100PPM 10 20 1/0.1PPM
sulfide
Ammonia 0-100PPM 20 50 1/0.1PPM
Hydrogen 0-1000PPM 200 500 1/0.1PPM
Chlorine
0-20PPM 5 10 1/0.1PPM
gas
Hydrogen
0-20PPM 5 10 1/0.1PPM
chloride
Sulfur
0-20PPM 5 10 1/0.1PPM
dioxide
Nitric
0-250PPM 50 125 1/0.1PPM
oxide
Nitrogen
0-20PPM 5 10 1/0.1PPM
dioxide
Please contact the company for other combination gases.
Error display (determined by sensor): ±5% FS (flammable
gas), ±10% (carbon monoxide) and ±5% (hydrogen sulfide)
Response time: T<30s
Indication: real-time data and system status will be
displayed on the LCD screen.
LED, sound, vibration indication alarm, fault and
undervoltage
Working environment: temperature of -20 ° C ~ 50 ° C;
humidity of less than 95% RH (no condensation)
Working voltage: DC3.7V (lithium battery capacity of
2000mAh)
Explosion-proof sign: Ex ib IIB T3 Gb
Charging time: 6h~8h
Standby time: more than 8 hours
Lifespan of the sensor: 2 years
Size：112*55*31(mm)
Weight：150g

4, function and operational methods

4.1 Self-test when turning on and preparation
When the detector is off, press the middle key for about 3
seconds. Hearing two “drops”, the backlight of the display
of the detector will be lit up. At the moment, the detector
is on, and the welcome is sprung on the screen. See Figure
1 and Figure 2

Welcome Starting please

wait…
Figure 1 Figure 2
When the welcome screen is over, the screen will display the
high, low and range information, such as carbon monoxide gas
as shown in Figure 3 as well as installed oxygen and other
information of gas displayed on other sensors.

Carbon monoxide
Low value 50PPM
High value 150PPM
Range 1000PPM

Figure 3
When the information is displayed, the system will enter the
self-test and the light self-test status, that is, the light
will flash twice; self-test of the vibrating piece means that
the vibrating piece will generate vibration and then stop;
the self-test of sound means that the bee sounder will beep
twice. The status mentioned above indicates that the
peripheral self-test has passed if normal. See Figure 4,
Figure 5 and Figure 6.

Light Starting please

self-inspection wait…
Figure 4 Figure 5

Voice
self-inspection

Figure 6
4.2 Normal status of detection and alarm
If the detector does not detect a gas above the concentration
of the low alarm value, the screen will normally display the
current detection value of the gas. For example, carbon
monoxide gas is shown in Figure 7.

Carbon monoxide

0 PPM
Figure 7
When the detector detects a lower limit alarm value that is
higher than that of any one of the gases, the detector will
alarm, and the backlight of the screen will light up, and
at the same time, the vibrating piece will also start to
vibrate. The detector will stop beeping and vibrating only
when the gas concentration is normal, and the backlight of
the screen will turn off.

4.3 Check of system status

When the user wants to check the current usage of the battery
and date and time, press the left button in the normal
detection state, the screen will display the information of
the date and time and battery power and voltage. See Figure
8
 Date: 00-00-00
Time: 00:00
Battery information: 3.7v
050%
Figure 8

4.4 Shut down

When the detector is in the normal detection state, press
the middle button for 3 seconds, the screen will display the
shutdown information, press the left key fr yes while the
right one for no. See Figure 9

Turn off?
Yes No

Figure 9

4.5 Charging
When the detector is in the normal detection state, the
battery voltage is lower than 3.5V, it will display the
message “Low battery, please charge”. At this time, you
need to insert the USB charging cable to charge immediately.
Otherwise, the system may not work properly due to the low
voltage. See Figure 10
 Low battery
Please charge

Figure 10
It can also be charged in the off state, and the charging
will display “Charging...”. See Figure 11

charging

Figure 11
When charging is over, “Ok” will be displayed.See Figure
12

Charging
finished

Figure 12

5、Menu guide
(1) On the menu: press the middle button to the main
menu
（2）On keys: Press the left button in the menu to select
up, cancel or press the right key to select the function.
Press the middle button to confirm, save or enter the
submenu.
（3）If the system doesn’t work for more than 5
seconds, the system automatically returns to the normal
detection.
Main menu
Menu Method of operation：
Press the left key to
﹣﹥Zero setup select the menu item,
Gas calibration press the right key to
to select the menu,
Warning setup press the middle
button to enter the
menu, and if you
Menu choose to exit, the
normal detection will
﹣﹥Alarm record be back again.
Time setup
Language switch

Menu
﹣﹥Exit

▲ enter ▼
 Zero trim
Zero fine-tuning In fact, this
function is available
-0000 to change the set
* value based on the
actual gas
▲ enter concentration.
▼ Operation
method: Enter the zero
fine adjustment
interface. When the
gas type is selected,
press the middle key
to enter the zero
trim. Press the left
key to the right to
choose the value or
symbol. Press the
right key to adjust
the current sign or
value. Press the
middle button to save
the adjustment.
For example,
when the value of
carbon monoxide in the
air is always
displayed as 3 not 0,
you can set -0004 and
then save it. Return
to the normal
detection interface.
At this time, the
value of the carbon
 monoxide is zero.
Note: the
setting value is
slightly larger than
the displayed value by
1 unit. If too large,
the display value will
be too different from
the actual gas
concentration, as a
result of being not
accurate.
Calibration
Input Password To prevent users from
affecting the work of
0000 the portable gas
* detector. This
feature sets a
▲ enter ▼ separate password.

Alarm settings
Low value High value This function is
used to set the alarm
limit when detecting
0050 0200 gas concentration.
The low alarm refers
* * to an audible and
▲ enter ▼ visual alarm when the
gas concentration
exceeds the low value.
The high alarm refers
to an audible and
visual alarm when the
 gas concentration
exceeds the high
value.
Method of operation：
Enter the
high-low-value
adjustment, press the
left button to adjust
each number. Press the
right key to adjust
the number. Press the
middle key to save it.
Alarm record
Alarm record The "Alarm Record"
menu consists of
﹣﹥View alarm "Alarm View", "Alarm
Alarm clear Clear", and "Exit".
Method of operation：
▲ enter ▼ Press the left key to
select the submenu,
and press the right
Alarm record one to select the
﹣﹥Exit submenu. When the gas
type is selected,
press the middle
﹣﹥Exit button to enter the
nest menu.
Alarm view
To view the
previous alarm
records.
Press the left key
to view the latest
 record and press the
Carbon monoxide right one to view the
last record. Exit
00-00-00 automatically without
Time: 00:00 operation for 5
seconds.
Low value 50
▲ ▼
Alarm clear
To clear alarm
records
Alarm clear Method of operation：
Press the left key to
select“Yes”to clear
YES NO the alarm record;
press the right one to
select“No”to cancel
the action.
Exit
Alarm record To exit the submenu of
Alarm Logging
﹣﹥Exit Method of operation：
Press the middle key
to exit.
▲ enter ▼
 Time setting
Please enter the year To set the current
time.
0000 Method of operation：
* Enter the "Time
Settings" and display
▲ enter ▼ the year setting.
Press the left key to
Please enter the elect the last two
digits, and press the
month right one to adjust
00 them.Press the middle
button to save it,
* then enter the month
setting, and so on.
▲ enter ▼
When you enter the
minute setting, press
Please enter date the middle button to
save all information
00 before exiting.
*
▲ enter ▼

Please enter hours

00
*
▲ enter ▼
 Please enter
a minute
00
*
▲ enter ▼

Language switching
Language switch This function is
used to switch
﹣﹥Chinese language, including
English Chinese, English, and
Exit.
▲ enter ▼ Method of operation：
Press the left key to
select the downward
Language switch language, press the
﹣﹥Exit right one to select
the upward language,
and press the middle
▲ enter ▼ one to confirm it.If
you select the
English, the system
language will switch
to it. To select
Chinese in the English
interface, and the
system language will
switch to Chinese.If
you choose to exit,
the submenu will
appear again.
Warning: please do not charge the portable gas detection
alarm at the inspection site to avoid fire or explosion.
Please do not charge the portable gas detector when it is
turned on, so as not to affect the charging speed.

6、Precautions for use

1 、 Prevent the unit from falling from high places or
vibrating；
2、The presence of high concentrations of gas may make the
machine fail to be used properly;
3、Please operate and use it in strict accordance with the
instructions, otherwise it may result in inaccurate test
results or damage to the unit.
4、This product must not be stored or used in an environment
with corrosive gases (such as with high-concentrations
chlorine, etc.), or in other harsh environments, including
extremely high or low temperatures, higher humidity,
electromagnetic fields, and strong sunlight and the same to
the store.
5、If the surface of the machine is dirty after a long period
of use, wipe it gently with a wet and soft cloth, instead
of corrosive solvents and hard objects. Otherwise, the
surface of the machine may be scratched or damage.
6、In order to ensure the accuracy of the detection, the
machine should be calibrated regularly and the period must
be within one year.
7、Any application or malfunction that is beyond the manual
should be contacted by our company for resolution.
8、The battery pack cannot be removed or replaced in an
explosive atmosphere, nor be charged.Peripheral plug-in
devices that are not certified for explosion protection
cannot be used in an explosive atmosphere. Replacing the
sensor is not allowed.

7、Common faults and their solutions

Fault Possibility Solution
Low voltage Charge in time
Please contact the dealer
Crash or manufacturer for
Fail to
repair
turn on
Please contact the dealer
Circuit failure or manufacturer for
repair
No
reaction Please contact the dealer
to the Circuit failure or manufacturer for
detectio repair
n gas
Please contact your
Sensor overdue dealer or manufacturer to
Inaccura
replace the sensor
te
Calibration fails
display
to be finished for a Calibrate in time
long time
Charge and reset time in
The battery runs out
Wrong time
time Strong
display electromagnetic Reset time
interference
Zero
calibrat
Excessive sensor Calibrate or replace the
ion
drift sensor in time
unavaila
ble
Range is
full on
the
light
instrume
Please contact your
nt when
Sensor failure dealer or manufacturer to
the
replace the sensor
normal
detectio
n is
carried
out.

8、Store
The detector shall be stored at the temperature of -10 °
C to 55 ° C and a relative humidity of less than 85%, and
where there is no harmful gases or impurities in the air that
corrode the detector.

9、Accessories and others

The supporting detector is made up of one package, one
portable single gas detector, one charger, one manual, and
one certificate card.
10、Schedule (Please check the parameters according to
the type of gas sensor)
Low High
Conventio Indicati Resoluti
Gas type alar alar
nal range on error on
m m
Oxygen 0-30%VOL ＜±3%FS 0.1%VOL 19.5 23.5
Flammabl
0-100%LEL ＜±3%FS 1%LEL 20 50
e gas
Carbon
0-1000PPM ＜±3%FS 1PPM 50 150
monoxide
Hydrogen
0-100PPM ＜±3%FS 1/0.1PPM 10 20
sulfide
Ammonia 0-100PPM ＜±3%FS 1/0.1PPM 20 50
Hydrogen 0-1000PPM ＜±3%FS 1/0.1PPM 200 500
Chlorine
0-20PPM ＜±3%FS 1/0.1PPM 5 10
gas
Hydrogen
0-20PPM ＜±3%FS 1/0.1PPM 5 10
chloride
Sulfur
0-20PPM ＜±3%FS 1/0.1PPM 5 10
dioxide
Sulfur
0-250PPM ＜±3%FS 1/0.1PPM 50 125
dioxide
Sulfur
0-20PPM ＜±3%FS 1/0.1PPM 5 10
dioxide