Technical Bulletin T 223.

496en

SANDVIK MINING AND CONSTRUCTION Prepared Checked Date Page

Sandvik SRP AB
SE-233 81 Svedala, Sweden Mario Begic Mjo 2008-10-22 1 (2)

Design change CH660:02 supersedes CH660:01

A number of improvements have been made to the CH660:01, which is thus superseded by the
CH660:02 version.

The most important improvements in the CH660:02 are:

• A new bottom shell design to increase strength

• Wearing liners in bottom shell replaced with rubber liners
• A new top shell design to increase strength
• A new spider cap with new top shell interface
• A new feed hopper
• Rubber liners in feed hopper and cone plates
• A stronger shrink fit of the head centre and main shaft
• A temperature transmitter has been added in the top shell spider hub

The improvements are described in more detail below:

The new bottom shell has four solid arms instead of two hollow arms. The pinionshaft arm and
the hub have been redesigned. Bolted polymer wear protection is used instead of welded
wearing liners. The inspection hatch has been replaced with a new polymer design. Due to the
changed location of arms, a new hydroset cylinder cover with new hoses has been designed.

The spider arms of the top shell have been strengthened. The arms and total height and the top
shell have been raised 90mm. To compensate for the top shell’s height increase, the height of
the spider cap has been decreased, so the total height of the crusher is unchanged. The spider
cap/top shell interface is redesigned with a new o-ring and longer screws. The design of the
stiffeners has also been optimized to improve strength.

A temperature transmitter has been added in the spider hub, level with the pivot point of the
spider bearing. This makes it possible to monitor the temperature of the spider bearing and thus
prevent major bearing failures.

The hopper has now a more robust four-piece design with rubber liners on the upper part of the
feed hopper and rubber clothing on the cone plates. The same inspection door as on larger
crushers has been used. The material for feed distributor boxes has been changed to Hardox
plate.

The infrared transceiver for level monitoring in the feed hopper has been replaced by the same
radar sensor used in CH880 and CH870. This is an analog sensor and can be programmed to
provide a 4-20mA current range to maintain optimum feed level in the hopper. The advantage
of this is that the feed can be smoother controlled and give better flow of material, also radar
instead of transceiver is easier to install and less sensitive to the environment
 Technical Bulletin T 223.496en

SANDVIK MINING AND CONSTRUCTION Prepared Checked Date Page

Sandvik SRP AB
SE-233 81 Svedala, Sweden Mario Begic Mjo 2008-10-22 2 (2)

Some comments on interchangeability:

• Old wearing plates will not fit on the new bottom shell and new polymer liners will not
fit on older crushers.

• The new top shell can be used on older crushers, but the old spider cap will not fit on
the new top shell.

• New cone plates do not fit on an old feed hopper. New feed hopper with new cone
plates fits on old crushers.

• The new main shaft assembly can be used on old crushers. Since the strength of the
shrink fit has improved and because an old main shaft can not be used with a new head
centre (or vice-versa), we will in the future only supply complete packages.

• New dust collar can be used on old crushers, but longer screws are needed.

• New hydroset cylinder cover and hoses for accumulator are not interchangeable

Mario Begic
Design Department Crushers
R&D
 7

01 9
2 3

9 1 452.4978-901 Hydroset system Ar. 236

8 1 YES 452.4132-901 Feed hopper Ar. 2162
7 1 YES 452.4130-901 Mainshaft Ar. 5891
6 1 YES 452.4131-901 Topshell Ar 6859
5 1 452.4129-901 Dust collar Ar 301
4 1 YES 452.4128-901 Eccentric Ar 1194
This drawing and all the enclosures belong to us. They must not be copied

given to a third party or used for manufacturing purposes without our per-

3 1 452.4127-901 Pinionshaft housing Ar 337

mission. As to infringements hereof, legal action will be taken with the
or duplicated - neither in original, nor in modified form - shown to or

2 1 - 452.4125-901 Bottomshell Ar. 7307

1 1 - 452.4126-901 Hydroset cylinder Ar. 1443
TOLERANSER/TOLERANCES Item No. Alt. Part No. Description Material Weight
Om ej annat angivits gäller / Unless otherwise specified
Pos. Nr. 901 Alt. Art. Nr. Benämning Material Vikt
Smältsvets.konstr / Welded constructions Svetsklasser enligt / Weld classes acc. to
Konstr/Designed Ritad/Drawn Beredd/Planned Kontr./Checked Godk./Approved Skala/Scale Vyplacering
SS-EN ISO 13920-B (SA 1121,200) SS-ISO 5817 (SA 1184,095) Vikt (kg)
M-gängor/M-threads
ISO 965-6H/6g (SA 1161,130)
U-gängor/U-threads
SMS 1718-2A/2B (SA 1161,150)
Gjutgods/Castings
ISO 8062-CT12 (SA 1121,300)
mbg spe mbg 1:15 E
Proj. method
Weight (Kg)

Generella toleranser för linjära mått och vinkelmått/General tolerances for linear and angular dimensions
CH660 25730
support of the existing law.

(m) Medel (c) Grov (v) Mycket grov Toleransklass

(m) Medium (c) Coarse (v) Very coarse Tolerance class Datum
2007-05-16 No.
01
Hydrocone
Date Rev
00 2007-12-13 mbg mbg Basmått / Basic dimension : <4000mm >4000mm
Ritn.nr/Drawing No.

452.4124
Bearb. med spånavskiljande verktyg (gäller ej sågning) ISO 2768-1-m SS-ISO 2768-1-c
Machined with cutting tools (does not include sawing) (SA 1121,100) (SA 1121,100)
01 2008-06-18 hjo hjo
Konkross
Bearb. med icke spånavskiljande verktyg (inkluderar sågning) ISO 2768-1-v SS-ISO 2768-1-v
Nr. Ant. Ändring Datum Införd Godkänd Machined with non-cutting tools (includes sawing) (SA 1121,100) (SA 1121,100)

Rev. No. Modification Date Changed Approved För brutna kanter och vinkelmått
For broken edges and angular dimensions
SS-ISO 2768-1-c
(SA 1121,100)
Format
A2 Blad
Sheet 1 av
of 1
 14 11

13 8

75
10
C
D (1 : 10)

75
1

C (1 : 15)
6 5 272

15
A-A
3 4

2
D

7 15 4 842.0013-00 Set Screw SK6SS 12x50 0

14 1 891.1772-901 Polymer wear protection 187
13 2 442.7907-01 Boss 2132-01 0.2
12 8 853.0646-00 Pin Prym N 16x45 0.1
11 1 - 442.8761-01 Ecc. wearing plate CC495K (SS 25
A B A 10 2 900.0276-00 Cover 3/4"
5640-15)
0.1
9 1 900.1412-00 Pipes Pipe KR 3/4"x70 0.1
8 1 900.0921-00 Swivel branch tee adapter 3/4" 0.3
7 1 853.0464-00 Pin CP m6 12x30 SMS 2374 0.0
6 1 442.8742-01 Bottom shell bushing JM 14-15 165
5 1 900.2108-00 Elbow 2.6
12 4 16 847.0124-00 Washer BRB 25x45 HB200 SS 3576 - 0.03
This drawing and all the enclosures belong to us. They must not be copied

given to a third party or used for manufacturing purposes without our per-

3 16 840.0669-00 Screw M6S 24x70 8.8 ISO 4017 Steel 0.4

mission. As to infringements hereof, legal action will be taken with the
or duplicated - neither in original, nor in modified form - shown to or

B (1 : 10) 2 1 452.4297-901 Foot As. 316

1 1 - 452.3765-001 Bottomshell GS200+N 6612
TOLERANSER/TOLERANCES Item No. Alt. Part No. Description Material Weight
901 Benämning Vikt
Om ej annat angivits gäller / Unless otherwise specified
Pos. Nr. Alt. Art. Nr. Material
Smältsvets.konstr / Welded constructions Svetsklasser enligt / Weld classes acc. to
Konstr/Designed Ritad/Drawn Beredd/Planned Kontr./Checked Godk./Approved Skala/Scale Vyplacering
SS-EN ISO 13920-B (SA 1121,200) SS-ISO 5817 (SA 1184,095) Vikt (kg)
M-gängor/M-threads U-gängor/U-threads Gjutgods/Castings jha mbg mbg 1:20 E Weight (Kg)

7316
ISO 965-6H/6g (SA 1161,130) SMS 1718-2A/2B (SA 1161,150) ISO 8062-CT12 (SA 1121,300) Proj. method

Generella toleranser för linjära mått och vinkelmått/General tolerances for linear and angular dimensions
support of the existing law.

(m) Medel (c) Grov (v) Mycket grov Toleransklass

(m) Medium (c) Coarse (v) Very coarse Tolerance class Datum
Date 2007-05-16 No.
Rev
01
Bottomshell Ar.
Basmått / Basic dimension : <4000mm >4000mm
00 2007-11-30 mbg mbg

452.4125
Bearb. med spånavskiljande verktyg (gõller ej sågning) ISO 2768-1-m SS-ISO 2768-1-c Ritn.nr/Drawing No.
Machined with cutting tools (does not include sawing) (SA 1121,100) (SA 1121,100)
01 Pos 15 new 2008-06-17 msa msa
Stativ underdel Ar.
Bearb. med icke spÕnavskiljande verktyg (inkluderar sågning) ISO 2768-1-v SS-ISO 2768-1-v
Ändring Machined with non-cutting tools (includes sawing) (SA 1121,100) (SA 1121,100)
Nr. Ant. Datum Införd Godkänd
Rev. No. Modification Date Changed Approved
För brutna kanter och vinkelmått
For broken edges and angular dimensions
SS-ISO 2768-1-c
(SA 1121,100)
Format
A3 Blad
Sheet 1 av
of 1
 14 3 12

8 9 10 11

4
7 13 2

14 1 442.8747-01 Seal ring inner 2

13 1 442.8808-01 Gasket 0
12 3 841.0019-00 Screw MC6S 10x40 12.9 0.04
11 1 442.8809-04 Shim 5150-02 0
10 1 442.8809-03 Shim 5150-02 0
9 1 442.8809-02 Shim 5150-02 0
8 1 442.8809-01 Shim 5122-04 0
7 1 442.8762-01 Locating bar 5640-15 3
6 16 847.0016-00 Washer BRB 17x30 HB200 ISO 7089 0
01 5 16 840.0074-00 Screw M6S 16x80 8.8 ISO 4014 0.2
4 1 853.0464-00 Pin CP m6 12x30 SMS 2374 0.0
This drawing and all the enclosures belong to us. They must not be copied

given to a third party or used for manufacturing purposes without our per-

3 1 442.8744-01 Ring 2134-01 17

mission. As to infringements hereof, legal action will be taken with the
or duplicated - neither in original, nor in modified form - shown to or

2 4 840.0634-00 Screw M6S 16x25 8.8 ISO 4017 - 0.1

EN-GJS-500- 278
1 1 452.4151-001 Dust collar
7
TOLERANSER/TOLERANCES Item No. Part No. Description Material Weight
Om ej annat angivits gäller / Unless otherwise specified
Pos. Nr. 901 Art. Nr. Benämning Material Vikt
Smältsvets.konstr / Welded constructions Svetsklasser enligt / Weld classes acc. to
Konstr/Designed Ritad/Drawn Beredd/Planned Kontr./Checked Godk./Approved Skala/Scale Vyplacering
SS-EN ISO 13920-B (SA 1121,200) SS-ISO 5817 (SA 1184,095) Vikt (kg)
M-gängor/M-threads U-gängor/U-threads Gjutgods/Castings jha mbg mbg 1:6 E Weight (Kg)

303
ISO 965-6H/6g (SA 1161,130) SMS 1718-2A/2B (SA 1161,150) ISO 8062-CT12 (SA 1121,300) Proj. method

CH660
Generella toleranser för linjära mått och vinkelmått/General tolerances for linear and angular dimensions
support of the existing law.

(m) Medel (c) Grov (v) Mycket grov Toleransklass

(m) Medium (c) Coarse (v) Very coarse Tolerance class Datum
Date 2007-05-16 No.
Rev
01
Dust collar Ar
Basmått / Basic dimension : <4000mm >4000mm
00 2007-11-30 mbg mbg

452.4129
Bearb. med spånavskiljande verktyg (gõller ej sågning) ISO 2768-1-m SS-ISO 2768-1-c Ritn.nr/Drawing No.
Machined with cutting tools (does not include sawing) (SA 1121,100) (SA 1121,100)
01 Pos 5. changed. 2008-02-14 mbg mbg
Glidring Ar
Bearb. med icke spÕnavskiljande verktyg (inkluderar sågning) ISO 2768-1-v SS-ISO 2768-1-v
Ändring Machined with non-cutting tools (includes sawing) (SA 1121,100) (SA 1121,100)
Nr. Ant. Datum Införd Godkänd
Rev. No. Modification Date Changed Approved
För brutna kanter och vinkelmått
For broken edges and angular dimensions
SS-ISO 2768-1-c
(SA 1121,100)
Format
A3 Blad
Sheet 1 av
of 1
 2

9
8

10

12

17 12 847.0016-00 Washer BRB 17x30 HB200 ISO 7089 0.01

17 15
13 16 17 16 1 840.0071-00 Screw M6S 16x65 8.8 ISO 4014 0.1
15 11 840.0069-00 Screw M6S 16x55 8.8 ISO 4017 0.1
11 14 1 442.8805-01 Scraper 819.0100 3
13 1 442.8804-01 Retainer 1142-32 0.4
12 1 442.8801-01 Retaining ring EN-JL 1040 101
14
Plastlaminat
Dust seal ring SIS
11 1 442.8802-01 168501/1210 13
/1220
10 1 452.0269-001 Burning ring 1312-00 4
1
9 1 442.8791-01 Inner head nut 42CrMo4 26
8 1 442.8800-00 Head nut with burn ring 85
7 1 YES 831.0016-00 Casting compound (kg) 0
6 1 x 452.4219-901 Mantle alt. 1192
5 1 855.0026-00 Retaining Ring Sga 100 SS1581 0.1
This drawing and all the enclosures belong to us. They must not be copied

given to a third party or used for manufacturing purposes without our per-

3 1 853.0119-00 Pin CP 25m6x60 SMS 2374 0.2

mission. As to infringements hereof, legal action will be taken with the
or duplicated - neither in original, nor in modified form - shown to or

3 2 1 442.8792-01 Main shaft sleeve 42CrMo4 82

1 1 452.4310-901 Mainshaft Assembly 4384
5 TOLERANSER/TOLERANCES Item No. Alt. Part No. Description Material Weight
Om ej annat angivits gäller / Unless otherwise specified
Pos. Nr. QTY. Alt. Art. Nr. Benämning Material Vikt
Smältsvets.konstr / Welded constructions Svetsklasser enligt / Weld classes acc. to
Konstr/Designed Ritad/Drawn Beredd/Planned Kontr./Checked Godk./Approved Skala/Scale Vyplacering
SS-EN ISO 13920-B (SA 1121,200) SS-ISO 5817 (SA 1184,095) Vikt (kg)
M-gängor/M-threads U-gängor/U-threads Gjutgods/Castings mbg spe mbg 1:10 E Weight (Kg)

5891
ISO 965-6H/6g (SA 1161,130) SMS 1718-2A/2B (SA 1161,150) ISO 8062-CT12 (SA 1121,300) Proj. method

CH660
Generella toleranser för linjära mått och vinkelmått/General tolerances for linear and angular dimensions
support of the existing law.

(m) Medel (c) Grov (v) Mycket grov Toleransklass

(m) Medium (c) Coarse (v) Very coarse Tolerance class Datum
Date 2007-05-16 No.
Rev
00
Mainshaft Ar
Basmått / Basic dimension : <4000mm >4000mm

452.4130
Bearb. med spånavskiljande verktyg (gõller ej sågning) ISO 2768-1-m SS-ISO 2768-1-c Ritn.nr/Drawing No.
Machined with cutting tools (does not include sawing) (SA 1121,100) (SA 1121,100)
00 2007-12-13 mbg mbg
Huvudaxel Ar
Bearb. med icke spÕnavskiljande verktyg (inkluderar sågning) ISO 2768-1-v SS-ISO 2768-1-v
Ändring Machined with non-cutting tools (includes sawing) (SA 1121,100) (SA 1121,100)
Nr. Ant. Datum Införd Godkänd
Rev. No. Modification Date Changed Approved
För brutna kanter och vinkelmått
For broken edges and angular dimensions
SS-ISO 2768-1-c
(SA 1121,100)
Format
A3 Blad
Sheet 1 av
of 1
 26
7 1 8 25 28 19 12 16 47

34 32
27
49

39 48
A (1 : 4) 48 1 452.4195-001 Steel Pipe DIN 2391/C-ST 35,4 15x1,5 0.5
47 2 900.0431-00 Compression fittings GE 15-LR 0.1

C 46 6 442.8290-01 Dowel Pin 0.7

A 45 1 - 442.8793-01 Support ring S355JR 177

31 44 54 863.0058-00 Disc spring 90x46x5 0.2
15 14 22
43 6 442.7271-01 Washer S355N 0.3
13 42 6 442.7253-01 Sleeve E335 0.4

41
C 41 6 845.0284-00 Lock Nut M30 8 FZB DIN 985 - 0.3
40 6 840.1075-00 Screw M6S 30x380 8.8 3.5
42 B B 39 4 YES 442.9415-00 Wear plate 30
44
38 6 442.7252-04 Shim S235JR 0
43 37 6 442.7252--03 Shim S235JR 0
36 6 442.7252-02 Shim S235JR 0
35 6 - 442.7252-01 Shim DC 01 0
5
34 6 442.8908-01 Hose 31.5-0.6 SS 248225 0
49 6 442.8881-01 Washer S355JR 2
B-B (1 : 5) 32 6 840.1074-00 Screw M6S 30x280 8.8 ISO 4014 1.8
31 1 YES 452.4289-901 Filler ring Alt. 1717
30 2 YES 831.0016-00 Casting compound (kg) 0
6
29 1 YES 452.4218-901 Concave Alt. 10076
40 29 30 45 46
28 1 900.0981-00 Plug BSPT 1" hexagon 0.1
Nitrilgummi
27 1 - 442.8755-01 Seal ring 1.5
60° SH
26 6 847.0132-00 Washer BRB 21x36 HB200 SS 3576 0.02

9 10 25 6 840.0652-00 Screw M6S 20x90 8.8 ISO 4017 0.3

24 1 191.3213-00 Connection box CBT
17 18
8 8 23 1 191.2376-00 Temperature Sensor TRPF 0.0
22 2 900.1030-00 Bushing RI-08-04 1/2"-1/4" 0.1
22 21 1 900.2624-00 Jam nut 1/2" 0.0
20 1 900.0654-00 Adapter G 1/2 BxG 1/2 B 0.1
19 1 442.8754-01 Spider bushing EN-GJL-350 87
23 21 20 11
18 4 847.0165-00 Washer TBRB 21x36 1370 SS 1466 0.0
17 4 840.0080-00 Screw M6S 20x80 8.8 ISO 4014 0.3

24 16 1 873.1401-00 O-Ring 594,1x5,7 SMS 1586 0.0

15 1 900.0002-00 Elbow 1/4 ISO49 A1 0.0
38 37 36 35 C-C (1 : 5)
14 1 900.0169-00 Nipple 1/4 ISO49 N8 0.0
13 1 912.0114-00 Air Filter P10102 R1/4" 0.3
12 1 452.3841-001 Spider cap GE300+N 340
11 1 914.0093-00 Lubrication Nipple AH R 1/4" 0.0
10 1 452.4153-001 Steel Pipe DIN 2391/C-ST 35,4 10x1,5 0.3
9 1 452.4154-001 Steel Pipe DIN 2391/C-ST 35,4 10x1,5 0.3
8 4 900.0425-00 Compression fittings GE 10-LR 0.0
7 2 - 442.8812-01 Arm shield 74
6 4 442.9530-01 Screw M6S 42x100 284.353
5 24 899.0278-00 Protective Cap SW65 2 H20 0.1
4 20 847.0171-00 Washer BRB 43x80 HB 200 SS 3576 0.2
This drawing and all the enclosures belong to us. They must not be copied

given to a third party or used for manufacturing purposes without our per-

3 20 845.0322-00 Nut M6M M42 8 FZB ISO 4032 0.6

mission. As to infringements hereof, legal action will be taken with the
or duplicated - neither in original, nor in modified form - shown to or

2 20 840.1073-00 Screws M6S 42x220 8.8 3.1

1 1 - 452.3760-001 Topshell GS200+N 4852
TOLERANSER/TOLERANCES Item No. Alt. Part No. Description Material Weight
Om ej annat angivits gäller / Unless otherwise specified
Pos. Nr. 901 Alt. Art. Nr. Benämning Material Vikt
Smältsvets.konstr / Welded constructions Svetsklasser enligt / Weld classes acc. to
Konstr/Designed Ritad/Drawn Beredd/Planned Kontr./Checked Godk./Approved Skala/Scale Vyplacering
SS-EN ISO 13920-B (SA 1121,200) SS-ISO 5817 (SA 1184,095) Vikt (kg)
M-gängor/M-threads
ISO 965-6H/6g (SA 1161,130)
U-gängor/U-threads
SMS 1718-2A/2B (SA 1161,150)
Gjutgods/Castings
ISO 8062-CT12 (SA 1121,300)
jha mbg 1:10 E
Proj. method
Weight (Kg)

Generella toleranser för linjära mått och vinkelmått/General tolerances for linear and angular dimensions
CH660 6859
support of the existing law.

(m) Medel (c) Grov (v) Mycket grov Toleransklass

(m) Medium (c) Coarse (v) Very coarse Tolerance class Datum
2007-05-16 No.
00
2 3 4 Topshell Ar
Date Rev
Basmått / Basic dimension : <4000mm >4000mm
Ritn.nr/Drawing No.

452.4131
Bearb. med spånavskiljande verktyg (gäller ej sågning) ISO 2768-1-m SS-ISO 2768-1-c
Machined with cutting tools (does not include sawing) (SA 1121,100) (SA 1121,100)
00 2007-12-06 mbg mbg
Stativöverdel Ar
Bearb. med icke spånavskiljande verktyg (inkluderar sågning) ISO 2768-1-v SS-ISO 2768-1-v
Nr. Ant. Ändring Datum Införd Godkänd Machined with non-cutting tools (includes sawing) (SA 1121,100) (SA 1121,100)

Rev. No. Modification Date Changed Approved För brutna kanter och vinkelmått
For broken edges and angular dimensions
SS-ISO 2768-1-c
(SA 1121,100)
Format
A2 Blad
Sheet 1 av
of 1
 11 10

12 13 5 6
9
5
19
1
2

4 3

5 6
7

19 1 900.2041-00 Swivel adapter G 3/4 B -14 0.2

18 5 847.0016-00 Washer BRB 17x30 HB200 ISO 7089 0
17 5 840.0065-00 Screw M6S 16x35 8.8 ISO 4017 - 0.10
16 1 YES 452.5088-901 Accumulator As. 57
14 15 1 452.4933-901 Hydroset cylinder cover liner 56
14 2 452.2899-001 Hose SAE 100 2" R10 Pt.
13 4 847.0132-00 Washer BRB 21x36 HB200 SS 3576 0.02
12 4 840.0650-00 Screw M6S 20x65 8.8 ISO 4017 0.23
11 4 847.0059-00 Washer TBRSB 13,5x36 - 0.01
10 4 840.0048-00 Screws M6S 12x45 8.8 ISO 1417 0.06
9 2 452.4862-001 Support Accumulator Pt. S355N 7.1
8 2 452.0441-001 Clamp Pt. 0.1
7 4 840.0076-00 Screw M6S M20x40 8.8 ZP Pt. 0.0
6 4 900.0659-00 Straight adapter G 2 B -11 0.1
5 6 873.0390-00 Seal ring, Tredo 30 0.0
4 2 873.0385-00 Tredo Nr.20 3/4" 0.0
18 17
This drawing and all the enclosures belong to us. They must not be copied

given to a third party or used for manufacturing purposes without our per-

3 1 900.2265-00 Plug VSTI R 3/4'' - ED 0.09

15
mission. As to infringements hereof, legal action will be taken with the
or duplicated - neither in original, nor in modified form - shown to or

2 1 900.0964-00 Swivel elbow adapter G 3/4 -14 0.3

(Skarpa kanter brytes / Sharp edges broken)

1 2 442.8777-00 Check valve Pt. 26
TOLERANSER/TOLERANCES Item No. Alt. Part No. Description Material Weight
Om ej annat angivits gäller / Unless otherwise specified
Pos. Nr. 452.4978-901 Alt. Art. Nr. Benämning Material Vikt
Smältsvets.konstr / Welded constructions Svetsklasser enligt / Weld classes acc. to
Konstr/Designed Ritad/Drawn Beredd/Planned Kontr./Checked Godk./Approved Skala/Scale Vyplacering
SS-EN ISO 13920-B (SA 1121,200) SS-ISO 5817 (SA 1184,095) Vikt (kg)
M-gängor/M-threads U-gängor/U-threads Gjutgods/Castings hjo mbg hjo 1:10 E Weight (Kg)

236
ISO 965-6H/6g (SA 1161,130) SMS 1718-2A/2B (SA 1161,150) ISO 8062-CT12 (SA 1121,300) Proj. method

CH660
Generella toleranser för linjära mått och vinkelmått/General tolerances for linear and angular dimensions
support of the existing law.

(m) Medel (c) Grov (v) Mycket grov Toleransklass

(m) Medium (c) Coarse (v) Very coarse Tolerance class Datum
Date 2008-06-10 No.
Rev
00
Hydroset system Ar.
Basmått / Basic dimension : <4000mm >4000mm

452.4978
Bearb. med spånavskiljande verktyg (gõller ej sågning) ISO 2768-1-m SS-ISO 2768-1-c Ritn.nr/Drawing No.
Machined with cutting tools (does not include sawing) (SA 1121,100) (SA 1121,100)
00 2008-07-07 hjo hjo
Hydrosetsystem Ar.
Bearb. med icke spÕnavskiljande verktyg (inkluderar sågning) ISO 2768-1-v SS-ISO 2768-1-v
Ändring Machined with non-cutting tools (includes sawing) (SA 1121,100) (SA 1121,100)
Nr. Ant. Datum Införd Godkänd
Rev. No. Modification Date Changed Approved
För brutna kanter och vinkelmått
For broken edges and angular dimensions
SS-ISO 2768-1-c
(SA 1121,100)
Format
A3 Blad
Sheet 1 av
of 1