OWNER’S OPERATING MANUAL

ELECTRIC CHAINSAW
MODEL CS-2000

SPECIFICATIONS
Voltage................................................................................................... 230V~50Hz
Rated input.................................................................................................... 2000W
No load speed........................................................................................... 8000min-1
Cutting length................................................................................................395mm
Chain brake.................................................................................................. < 0.12s
Bar length............................................................................................... 16”/400mm
Chain speed....................................................................................................13m/s
Chain oil tank capacity.................................................................................... 260ml
Automatic lubrication...........................................................................................Yes
Cable length.....................................................................................................35cm
Sound pressure level.......................................................LpA 89.3dB(A),k=2.5dB(A)
Sound power level........................................................ LWA 100.3dB(A),k=2.5dB(A)
Vibration level......................................................................... 7.618m/s2, K=1.5m/s2
Net weight........................................................................................................ 5.2kg

THANK YOU FOR BUYING A RYOBI

ELECTRIC CHAINSAW
Your new electric chainsaw has been engineered and manufactured to Ryobi’s
high standard of dependability, ease of operation and operator safety. Properly
cared for, it will give you years of rugged, trouble free performance. If you use
your electric chainsaw properly and only for what it is intended, you will enjoy
years of safe, reliable service.

CAUTION: Carefully read through this entire owner’s

manual, paying close attention to the general
safety rules and rules for safe operation,
before using.

KEEP THIS MANUAL FOR FUTURE REFERENCE

1
 IMPORTANT SAFETY INSTRUCTIONS
The purpose of safety rules is to attract your WARNING
attention to possible dangers. The safety symbols Chainsaws are potentially dangerous
and the explanations with them, require your tools. Accidents involving the use of
careful attention and understanding. The safety chainsaws often result in loss of limbs or
warnings do not by themselves eliminate any death. It is not just the chainsaw that is
danger. The instruction or warnings they give are the hazard. Falling branches, toppling
not substitutes for proper accident prevention trees, rolling logs can all kill.
measures.
Diseased or rotting timber poses
SAFETY ALERT SYMBOL. Indicates additional hazards. You should assess
danger, caution or warning. May be used your capability of completing the task
in conjunction with other symbols or safely. If there is any doubt, leave it to a
pictures. professional tree surgeon.
Failure to obey a safety warning can result in CHAINSAW SAFETY WARNINGS
serious injury to yourself or to others. Always follow Keep all parts of the body away from the saw chain
the safety precautions to reduce the risk of fire, when the chainsaw is operating. Before you start
electric shock and personal injury. the chainsaw, make sure the saw chain is not
contacting anything. A moment of inattention while
Do not attempt to operate this tool until you have operating chainsaws may cause entanglement of
read thoroughly and completely understood the your clothing or body with the saw chain.
safety rules, etc. contained in this manual. Failure
to comply can result in accidents involving fire, Always hold the chainsaw with your right hand on
electric shock or serious personal injury. Save this the rear handle and your left hand on the front
Owners Operating Manual and review it frequently handle. Holding the chainsaw with a reversed hand
for continual safe operation and for instructing configuration increases the risk of personal injury
others who may use this tool. and should never be done.
INTENDED USE Hold the power tool by gripping surface only,
The product is only intended for use outdoors. For because the saw chain may contact hidden wiring
safety reasons the product must be adequately or its own cord. Saw chains contacting a “live” wire
controlled by using two-handed operation at all may make exposed metal parts of the power tool
times. “live” and could give the operator an electric shock.
The product is designed for cutting branches, Wear safety glasses and hearing protection.
trunks, logs and beams of a diameter determined Further protective equipment for head, hands, legs
by the cutting length of the guide bar. It is only and feet is recommended. Adequate protective
designed to cut wood. It is only to be used in clothing will reduce personal injury by flying debris
domestic application by adults who have received or accidental contact with the saw chain.
adequate training on the hazards and preventative
measures/actions to be taken whilst using it. Do not operate a chainsaw in a tree. Operation of a
chainsaw while up in a tree may result in personal
Do not use the product for any purpose not listed injury.
above. It is not to be used for professional tree
services. The product is not to be used by children Always keep proper footing and operate the
or by persons not wearing adequate personal chainsaw only when standing on fixed, secure and
protective equipment and clothing. level surface. Slippery or unstable surfaces such as
ladders may cause a loss of balance or control of
WARNING the chainsaw.
To reduce the risk of injury, the user must
read and understand the operator’s When cutting a limb that is under tension be alert
manual. for spring back. When the tension in the wood
fibres is released the spring loaded limb may strike
the operator and/or throw the chainsaw out of
control.

2
 IMPORTANT SAFETY INSTRUCTIONS
Use extreme caution when cutting brush and Maintain a firm grip, with thumbs and fingers
saplings. The slender material may catch the saw encircling the chainsaw handles, with both hands
chain and be whipped toward you or pull you off on the saw and position your body and arm to allow
balance. you to resist kickback forces. Kickback forces can
be controlled by the operator, if proper precautions
Carry the chainsaw by the front handle with the are taken. Do not let go of the chainsaw.
chainsaw switched off and away from your body.
Do not overreach and do not cut above shoulder
When transporting or storing the chainsaw always height. This helps prevent unintended tip contact
fit the guide bar cover. Proper handling of the and enables better control of the chainsaw in
chainsaw will reduce the likelihood of accidental unexpected situations.
contact with the moving saw chain.
Only use replacement bars and chains specified by
Follow instructions for lubricating, chain tensioning the manufacturer. Incorrect replacement bars and
and changing accessories. Improperly tensioned or chains may cause chain breakage and/or kickback.
lubricated chain may either break or increase the
chance for kickback. Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain.
Keep handles dry, clean, and free from oil and Decreasing the depth gauge height can lead to
grease. Greasy, oily handles are slippery causing increased kickback.
loss of control.
ADDITIONAL CHAINSAW SAFETY WARNINGS
Cut wood only. Do not use chainsaw for purposes It is recommended to cut logs on a saw-horse or
not intended. For example: do not use chainsaw for cradle when operating the product the first time.
cutting plastic, masonry or non-wood building
materials. Use of the chainsaw for operations Ensure all guards, handles and spiked bumper are
different than intended could result in a hazardous properly fitted and are in good condition.
situation.
Persons using this chainsaw should be in good
CAUSES AND OPERATOR PREVENTION OF health. The chainsaw is a heavy unit so the
KICKBACK operator requires to be physically fit. The operator
Kickback may occur when the nose or tip of the should be alert, have good vision, mobility, balance
guide bar touches an object, or when the wood and manual dexterity. If there is any doubt, do not
closes in and pinches the saw chain in the cut. operate the chainsaw.
Tip contact in some cases may cause a sudden Do not start using the product until you have a
reverse reaction, kicking the guide bar up and back clear work area, secure footing, and a planned
towards the operator. retreat path away from the falling tree.
Pinching the saw chain along the top of the guide Beware of the emission of lubricant mist and saw
bar may push the guide bar rapidly back towards dust. Wear a mask or respirator if required.
the operator.
Electric power should be supplied via a residual
Either of these reactions may cause you to lose current device (RCD) with a tripping current of not
control of the saw which could result in serious more than 30 mA.
personal injury. Do not rely exclusively upon the
safety devices built into your saw. As a chainsaw If the power cable becomes damaged, you must
user, you should take several steps to keep your return the machine to an authorised service centre
cutting jobs free from accident or injury. for repair or replacement.

Kickback is the result of tool misuse and/or Always keep the power cable tidy and away from
incorrect operating procedures or conditions and the area of cutting. Apart from the danger of
can be avoided by taking proper precautions as electrocution, untidy cables cause falls and trips.
follows: Do not cut vines and/or small undergrowth (less
than 75 mm in diameter).

3
 IMPORTANT SAFETY INSTRUCTIONS
Always hold the chainsaw with both hands when Do not cut with your body in line with the guide bar
operating the saw. Use a firm grip with thumbs and and chain. If you do experience kickback this will
fingers encircling the chainsaw handles. Right hand help prevent the chain coming into contact with
must be on the rear handle and left hand on the your head or body.
front handle.
Do not use a back and forward sawing motion, let
Before starting the tool, make sure the saw chain is the chain do the work, keep the chain sharp and
not contacting any object. don’t try to push the chain through the cut.
Do not modify your tool in any way or use it to Do not put pressure on the saw at the end of the
power any attachments or devices not cut. Be ready to take on the weight of the saw as it
recommended by the manufacturer for your saw. cuts free from the wood. Failure to do so could re-
sult in possible serious personal injury.
There should be a first-aid kit containing large
wound dressings and a means to summon Do not stop the saw in the middle of a cutting
attention (e.g., whistle) close to the operator. A operation. Keep the saw running until it is already
larger more comprehensive kit should be removed from the cut.
reasonably nearby.
PUSH & PULL
The operator may be tempted to remove the The reaction force is always opposite to the
helmet if there is no danger of falling objects in the direction the chain is moving. Thus, the operator
work area, but remember the helmet, particularly must be ready to control the tendency for the
with the mesh visor, can help reduce the potential machine to pull away (forward motion) when cutting
for injury to the face and head if kickback occurs. on the bottom edge of the bar and the push
backwards (towards the operator) when cutting
An incorrectly tensioned chain can jump off the along the top edge.
guide bar and could result in serious injury or
fatality. The length of chain depends on the SAW JAMMED IN THE CUT
temperature. Check the tension frequently. Stop the chainsaw and make it safe. Do not try to
force the chain and bar out of the cut as this is
You should get used to your new chainsaw by likely to break the chain which may swing back and
making simple cuts on securely supported wood. strike the operator. This situation normally occurs
Do this whenever you have not operated the saw because the wood is incorrectly supported and
for some time. forcing the cut to close under compression thereby
To reduce the risk of injury associated with pinching the blade. If adjusting the support does
contacting moving parts, always stop the motor, not release the bar and chain, use wooden wedges
apply chain brake, remove the plug from the power or a lever to open the cut and release the saw.
socket and make sure all moving parts have come Never try to start the chainsaw when the guide bar
to a stop before: is already in a cut or kerf.

• cleaning or clearing a blockage PERSONAL PROTECTIVE EQUIPMENT

Good quality, personal protective equipment as
• leaving the product unattended used by professionals will help to reduce the risk of
injury to the operator. The following items should
• installing or removing attachments
be used when operating your chainsaw:
• checking, maintenance or working on the
SAFETY HELMET
machine
Should comply with EN 397 and be CE marked.
The size of the work area depends on the job being
HEARING PROTECTION
performed as well as the size of the tree or work
Should comply with EN 352-1 and be CE marked.
piece involved. For example, felling a tree requires
a larger work area than making other cuts, i.e., EYE AND FACE PROTECTION
bucking cuts, etc. The operator needs to be aware Should be CE marked and comply with EN 166 (for
and in control of everything happening in this work safety glasses) or EN 1731 (for mesh visors).
area.

4
 IMPORTANT SAFETY INSTRUCTIONS
GLOVES cold and dampness, diet, smoking and work
Should comply with EN381-7 and be CE marked. practices are all thought to contribute to the
development of these symptoms. There are
LEG PROTECTION (CHAPS) measures that can be taken by the operator to
Should comply with EN381-5, be CE marked and possibly reduce the effects of vibration:
provide all-round protection.
• Keep your body warm in cold weather. When
CHAINSAW SAFETY BOOTS operating the unit wear gloves to keep the
Should comply with EN ISO 20345:2004 and be hands and wrists warm. It is reported that cold
marked with a shield depicting a chainsaw to show weather is a major factor contributing to
compliance with EN 381-3. (Occasional users may Raynaud’s Syndrome.
use steel toe-cap safety boots with protective
gaiters which conform to EN 381-9 if the ground is • After each period of operation, exercise to
even and there is little risk of tripping or catching on increase blood circulation.
undergrowth).
• Take frequent work breaks. Limit the amount of
CHAINSAW JACKETS FOR UPPER BODY exposure per day.
PROTECTION
Should comply with EN 381-11 and be CE marked. • Protective gloves available from professional
chainsaw retailers are designed specifically for
RESIDUAL RISKS chainsaw use which give protection, good grip
Even when the product is used as prescribed, it is and also reduce the effect of handle vibration.
still impossible to completely eliminate certain These gloves should comply with EN381-7 and
residual risk factors. The following hazards may must be CE marked.
arise in use and the operator should pay special
attention to avoid the following: If you experience any of the symptoms of this
condition, immediately discontinue use and see
• Injury caused by vibration. Always use the right your doctor about these symptoms.
tool for the job, use designated handles and
restrict working time and exposure. WARNING
Injuries may be caused, or aggravated,
• Exposure to noise can cause hearing injury. by prolonged use of a tool. When using
Wear ear protection and limit exposure. any tool for prolonged periods, ensure
you take regular breaks.
• Contact with exposed saw teeth of the chain
(cutting hazards). GENERAL SAFETY RULES
WARNING! Read all instructions Failure to follow
• Unforeseen, abrupt movement or kickback of all instructions listed below may result in electric
the guide bar (cutting hazards). shock, fire and/or serious injury. The term "power
• Parts ejected from the saw chain tool" in all of the warnings listed below refers to
(cutting/injection hazards). your mains operated (corded) power tool or battery
operated (cordless) power tool.
• Thrown out pieces of the work piece
(wood chips, splinters). SAVE THESE INSTRUCTIONS

• Inhalation of saw dust and particles. 1) WORK AREA

• Skin contact with lubricant/oil. a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
RISK REDUCTION
It has been reported that vibrations from hand-held b) Do not operate power tools in explosive
tools may contribute to a condition called atmospheres, such as in the presence of
Raynaud’s Syndrome in certain individuals. flammable liquids, gases or dust. Power tools
Symptoms may include tingling, numbness and create sparks which may ignite the dust or
blanching of the fingers, usually apparent upon fumes.
exposure to cold. Hereditary factors, exposure to

5
 IMPORTANT SAFETY INSTRUCTIONS
c) Keep children and bystanders away while plugging in power tools that have the switch on
operating a power tool. Distractions can cause invites accidents.
you to lose control.
d) Remove any adjusting key or wrench before
2) ELECTRICAL SAFETY turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
a) Power tool plugs must match the outlet. Never result in personal injury.
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power e) Do not overreach. Keep proper footing and
tools. Unmodified plugs and matching outlets balance at all times. This enables better control
will reduce risk of electric shock. of the power tool in unexpected situations.
b) Avoid body contact with earthed or grounded f) Dress properly. Do not wear loose clothing or
surfaces such as pipes, radiators, ranges and jewellery. Keep your hair, clothing and gloves
refrigerators. There is an increased risk of away from moving parts. Loose clothes,
electric shock if your body is earthed or jewellery or long hair can be caught in moving
grounded. parts.
c) Do not expose power tools to rain or wet g) If devices are provided for the connection of
conditions. Water entering a power tool will dust extraction and collection facilities, ensure
increase the risk of electric shock. these are connected and properly used. Use of
these devices can reduce dust related hazards.
4) POWER TOOL USE AND CARE
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.

a) Do not force the power tool. Use the correct

Keep cord away from heat, oil, sharp edges or

power tool for your application. The correct

moving parts. Damaged or entangled cords

power tool will do the job better and safer at the

increase the risk of electric shock.

e) When operating a power tool outdoors, use an rate for which it was designed.
b) Do not use the power tool if the switch does not
extension cord suitable for outdoor use. Use of

turn it on and off. Any power tool that cannot be

a cord suitable for outdoor use reduces the risk

controlled with the switch is dangerous and

of electric shock.
f) If operating a power tool in a damp location is must be repaired.
c) Disconnect the plug from the power source
unavoidable, use a residual current device

before making any adjustments, changing

(RCD) protected supply. Use of an RCD

accessories, or storing power tools. Such

reduces the risk of electric shock.
3) PERSONAL SAFETY preventive safety measures reduce the risk of
a) Stay alert, watch what you are doing and use starting the power tool accidentally.
common sense when operating a power tool. d) Store idle power tools out of the reach of
Do not use a power tool while you are tired or children and do not allow persons unfamiliar
under the influence of drugs, alcohol or with the power tool or these instructions to
medication. A moment of inattention while operate the power tool. Power tools are
operating power tools may result in serious dangerous in the hands of untrained users.
personal injury.
e) Maintain power tools. Check for misalignment
b) Use personal protective equipment. Always or binding of moving parts, breakage of parts
wear eye protection. Safety equipment such as and any other condition that may affect the
dust mask, non-skid safety shoes, hard hat, or power tools operation. If damaged, have the
hearing protection used for appropriate power tool repaired before use. Many accidents
conditions will reduce personal injuries. are caused by poorly maintained power tools.
c) Avoid accidental starting. Ensure the switch is
in the off position before plugging in. Carrying
power tools with your finger on the switch or

6
 IMPORTANT SAFETY INSTRUCTIONS
f) Keep cutting tools sharp and clean. Properly Operating similar tools nearby increases both the
maintained cutting tools with sharp cutting risk of hearing injury and the potential for other
edges are less likely to bind and are easier to persons to enter your working area.
control.
Keep firm footing and balance. Do not overreach.
g) Use the power tool, accessories and tool bits Overreaching can result in loss of balance and can
etc., in accordance with these instructions and increase the risk of kickback.
in the manner intended for the particular type of
power tool, taking into account the working Keep all parts of your body away from any moving
conditions and the work to be performed. Use of part.
the power tool for operations different from Inspect the machine before each use. Check for
intended could result in a hazardous situation. correct operation of all controls including the chain
5) SERVICE brake.

a) Have your power tool serviced by a qualified Check for loose fasteners, make sure all guards,
repair person using only identical replacement and handles are properly and securely attached.
parts. This will ensure that the safety of the Replace any damaged parts before use.
power tool is maintained. Do not modify the machine in any way or use parts
ADDITIONAL GENERAL SAFETY WARNINGS and accessories which are not recommended by
Some regions have regulations that restrict the use the manufacturer.
of the product. Check with your local authority for If you need to use an extension cable ensure it is
advice. suitable for outdoor use and has a current capacity
Never allow children or people unfamiliar with the sufficient to supply your tool, check it before every
instructions to use the product. Local regulations use for damage, always uncoil it during use
may restrict the age of the operator. because coiled cables can overheat.

Ensure before each use that all controls and safety WARNING
devices function correctly. Do not use the power If the machine is dropped, suffers heavy
tool if the “off” switch does not stop the motor. impact or begins to vibrate abnormally,
immediately stop the machine and
Wear full eye and hearing protection, strong sturdy inspect for damage or identify the cause
gloves as well as head protection while operating of the vibration.
the product; use a face mask if operation is dusty.
Any damage should be properly repaired
Do not wear loose fitting clothing, short trousers or or replaced by an authorised service
jewellery of any kind. centre.
Secure long hair so it is above shoulder level to
The operation of any tool
prevent entanglement in moving parts.
can result in foreign objects
Beware of thrown, flying or falling objects; keep all being thrown into your
bystanders, children, and animals at least 15 m eyes, which can result in
away from work area. severe eye damage.
Before beginning power
Do not operate in poor lighting. The operator tool operation, always wear safety goggles or
requires a clear view of the work area to identify safety glasses with side shields and a full face
potential hazards. shield when needed. We recommend Wide
Use of hearing protection reduces the ability to Vision Safety Mask for use over eye glasses or
hear warnings (shouts or alarms). The operator standard safety glasses with side shields.
must pay extra attention to what is going on in the
working area.

7
 DESCRIPTION

1 2 3 4 5 6 7

9 10 11 12 13 14 15

1. Chain 9. Cord retainer

2. Guide bar 10. On/off trigger
3. Front hand guard/Chain brake 11. Chain lubricant measurement gauge
4. Front handle 12. Sprocket cover
5. Chain lubricant cap 13. Chain tensioner adjustment ring
6. Trigger release 14. Guide bar locking knob
7. Rear handle 15. Guide bar cover
8. Spiked bumper

8
 SAFETY DEVICES
LOW KICK-BACK SAW CHAIN GUIDE BARS
A low-kick-back saw chain helps to reduce the Generally, guide bars with small radius tips have
possibility of a kickback event. somewhat lower potential for kick-back. You should
use a guide bar and matching chain which is just
The rakers (depth gauges) ahead of each cutter long enough for the job.
can minimize the force of a kick-back reaction by
preventing the cutters from digging in too deeply. Longer bars increase the risk of loss of control
Only use replacement guide bar and chain during sawing. Regularly check the chain tension.
combinations recommended by the manufacturer. When cutting smaller branches (less than the full
length of the guide bar) the chain is more likely to
As saw chains are sharpened, they lose some of be thrown off if the tension is not correct.
the low kickback qualities and extra caution is
required. For your safety, replace saw chains when CHAIN BRAKE
cutting performance decreases. Chain brakes are designed to quickly stop the
chain rotating. When the chain brake lever/hand
SPIKED BUMPER guard is pushed towards the bar, the chain should
The integral bumper spike may be used as a pivot stop immediately. A chain brake does not prevent
when making a cut. It helps to keep the body of the kick-back. It only lowers the risk of injury should the
chainsaw steady while cutting. When cutting, push chain bar contact the operator’s body during a
the machine forward until the spikes dig into the kick-back event. The chain brake should be tested
edge of the wood, then by moving the rear handle before each use for correct operation in both the
up or down in the direction of the cutting line it can run and brake positions.
help ease the physical strain of cutting.

UNPACKING
CAUTION. This packaging contains If any parts are found to be missing, the machine
sharp objects. Take care when and its accessories should be returned together in
unpacking. Remove the machine, their original packaging to the retailer. Do not throw
together with the accessories supplied, from the the packaging away, keep it safe throughout the
packaging. Check carefully to ensure that the guarantee period, then recycle if possible,
machine is in good condition and account for all the otherwise dispose of it by the proper means. Do
accessories listed in this manual. Also make sure not let children play with empty plastic bags due to
that all the accessories are complete. the risk of suffocation.

ASSEMBLY
PACKING CONTENTS WARNING. Do not connect to power
• Chainsaw supply until assembly is complete.
• Chain Failure to comply could result in
• Guide bar accidental starting and possible serious
• Guide bar cover personal injury.
• Operator’s manual.
WARNING. Do not attempt to modify this
WARNING. If any parts are damaged or product or create accessories not
missing, do not operate this product until recommended for use with this product.
the parts are replaced. Use of this Any such alteration or modification is
product with damaged or missing parts misuse and could result in a hazardous
could result in serious personal injury. condition leading to possible serious
personal injury.

9
 ASSEMBLY
ASSEMBLING SAW CHAIN AND GUIDE BAR
Disconnect the mains plug. Wear protective gloves. 4

Unscrew the guide bar locking knob (1) and

remove the sprocket cover (2), Fig.1.

1
3

Fig. 3
Replace the sprocket cover and turn the guide bar
locking knob until nearly tight, Fig.3 (4).
Turn the chain tension adjustment ring until the saw
Fig. 1 chain is properly tensioned, Fig.4. The guide bar
must then be pushed upwards, check chain tension
The saw chain should face in the direction of chain again, do not tension the chain too tight.
rotation. If they face backwards, turn the loop over.
After the chain is well-tensioned, tighten the knob
Place the chain drive links into the bar groove, again.
Fig.2.

Fig. 2
Fig. 4
Position the chain so there is a loop at the back of
the bar.
Hold the chain in position on the bar and place the
loop around the drive sprocket, Fig.3. Lower the
bar so that the bolt goes through the hole in the
attached chain tension assembly (3). You may
need to rotate this assembly so the bolt and hole
align. You may rotate this assembly again to apply
some tension to the chain which will help keep it in
place.

10
 ASSEMBLY
ADJUSTING THE CHAIN TENSION
Loosen the guide bar locking knob slightly by
turning it counterclockwise.
To increase the chain tension, turn the chain
tensioner adjustment ring clockwise and check the
chain tension frequently. To reduce the chain
tension, turn the chain tensioner adjustment ring
counterclockwise and check the chain tension 3-4 mm
frequently.
The chain tension is correct when the gap between
the cutter in the chain and the bar is between
3-4mm. Pull the chain in the middle of the lower
side of the bar downwards (away from the bar) and
measure the distance between the bar and the
chain cutters, Fig.5. Fig. 5
Tighten the guide bar locking knob by turning it
clockwise.

ADDING CHAIN LUBRICATING OIL

WARNING. Never work without chain Clear surface around the oil cap to prevent
lubricant. If the saw chain is running contamination.
without lubricant, guide bar and saw
chain can be damaged. It is therefore Unscrew and remove the cap from the oil tank,
essential to check the oil level in the oil Fig.6.
level gauge frequently and every time Pour oil into the oil tank and monitor the oil level
before starting to use the chain saw. gauge. Ensure that no dirt enters the oil tank while
CHAIN LUBRICANT filling. The manufacturer recommends you use only
• Proper lubrication of the chain while in Ryobi chainsaw lubricating oil. (Available from your
operation reduces the friction between the authorised Ryobi service centre)
chain and the guide bar and assures a longer Put the oil cap back on and tighten it up. Wipe
tool life. Use only special chain oil of a high away any spillage.
quality for this purpose.
• Do not use any waste or reclaimed oil as this One full oil tank will enable you to use the saw for
could cause various problems with the oil 20-40 minutes.
pump.
SAW CHAIN / BAR LUBRICATION
Adequate lubrication of the saw chain is essential
at all times to minimize friction with the guide bar.
Never starve the bar and chain of oil. Running the
saw with too little oil will decrease cutting efficiency,
shorten saw chain life, cause rapid dulling of chain,
and cause excessive wear of bar from overheating.
Too little oil is evidenced by smoke, bar
discolouration or pitch build-up. New chains/bars
should be lubricated by hand before starting.

Fig. 6

11
 OPERATION
CONNECTING TO A POWER SUPPLY
This product is designed with a power cable
retainer that prevents the extension cord from
being pulled loose while using.
Form a loop with the end of the extension cord.
Insert loop portion of extension cord through the
opening in the bottom of the rear handle and place
over power cable retainer, Fig.7.
Slowly pull loop against power cable retainer until
the slack is removed.
Fig. 7
Plug product into extension cord.
NOTE: Failure to remove all excess cord slack
from extension cord retainer could result in plug
loosening from the receptacle.
NOTE: Use only approved outdoor extension
cords.
NOTICE: Always use cord retainer to properly
attach extension cord to the chainsaw. Failure to
use cord retainer may result in damage to the
chainsaw and/or extension cord.
HOLDING THE CHAIN SAW
Always hold the chain saw with your right hand at
the rear handle and your left hand at the front
handle. Grip both handles with the thumbs and
fingers encircling the handles. Ensure that your left
hand is holding the front handle so that your thumb
is underneath, Fig.8.
STARTING THE CHAIN SAW
Connect to power outlet. Make sure the chain
brake is in the run position by pulling back on the Fig. 8
lever/handguard, Fig.8 (1).
To start the machine press the trigger release,
Fig.8 (2), and then press the on/off trigger, 1 2
Fig.8 (3).

Fig. 9

12
 OPERATION
CHECKING AND OPERATING CHAIN BRAKE
Engage the chain brake by rotating your left hand
around the front handle. Allow the back of your
hand to push the chain brake lever/hand guard
toward the bar while the chain is rotating rapidly.
A
Be sure to maintain both hands on the saw handles
at all times.
Reset the chain brake back into the Run position
by grasping the top of the chain brake lever/hand
guard and pulling toward the front handle until you
hear a click.
Fig. 10
WARNING. If the chain brake does not
stop the chain immediately, or if the
chain brake will not stay in the run
position without assistance, take the saw
to an authorised service centre for repair
prior to use.
OPERATION
The following section on the operation of the chain
saw is a general guide only. The use of a chain saw
by an inexperienced person can be extremely
dangerous. If you are unsure, please seek the
assistance of a professional or get suitable training
before using the chain saw. Fig. 11
WARNING. Before every use check the
operation of the chain break and oil
pump.
BUCKING SPIKES
The chainsaw has bucking spikes (Fig.10-A) to
assist with cutting and reduce the chance of
kickback. Keep the bucking spikes touching the
wood when cutting will help prevent any pinching or
kick-back.
BUCKING
Bucking is cutting a log into lengths for easier
handling. To saw a log lying on the ground, first Fig. 12
saw halfway, then roll the log over and cut from the
opposite side (Fig.11). To saw the end of a log WARNING. Be careful that the chain
supported off the ground, first saw up from the does not cut into the ground when
bottom one-third through the log then finish by bucking as this causes rapid dulling of
sawing down from the top. To saw a log in the the chain.
middle of two supports holding it off the ground,
first saw down from the top one-third through the
log then finish by sawing up from the bottom
(Fig.12).When bucking on a slope, always stand on
the uphill side.

13
 OPERATION
LIMBING
Limbing is the process of removing the branches
from a fallen tree. Check the direction in which a
branch will bend before cutting it. Always cut on the
opposite side to the bending direction so that the
guide bar is not pinched in the cut. For large limbs
that cannot be removed in one cut, make an initial
cut from the bent side and finish by sawing from
the opposite direction (Fig.19). Do not remove
limbs that are supporting the fallen tree on the
ground until the tree has been cut into lengths.
WARNING. Always keep a well balanced Fig. 13
stance. Do not stand on the log. Be alert
to the fact that the log may roll over.
When working on a slope, always stand
on the uphill side of the log.
PRUNING
Pruning is the removal of a limb or branch from a
standing tree.
WARNING. Do not use an unstable
foothold or ladder. Do not overreach. Do
not saw above shoulder height. Always
use both hands to hold the saw. First cut
up from the bottom and finish down from
the top, Fig.14.
FELLING
Felling is the term for cutting down a tree. Small
trees up to 6-7 inches (15-18cm) in diameter are
usually cut in a single cut. Larger trees require
notch cuts. Notch cuts determine the direction the
tree will fall.
WARNING. Do NOT fell trees unless you
have received the appropriate training.
A retreat path (Fig.15- A) should be
planned and cleared as necessary
before cuts are started. The retreat path Fig. 14
should extend back and diagonally to the
rear of the expected line of fall, as
illustrated.
NOTE: Direction of fall (Fig.21-B) is
controlled by the notching cut. Before
any cuts are made, consider the location
of larger branches and natural lean of
the tree to determine the way the tree
will fall.

Fig. 15

14
 OPERATION
GENERAL GUIDELINES FOR FELLING TREES
Normally felling consists of 2 main cutting opera-
tions, notching (Fig.16-C) and making the felling
cut (Fig.16-D).
Start making the upper notch cut (Fig.16-C) on the
side of the tree facing the felling direction
(Fig.16-E).
Be sure you don t make the lower cut too deep in-
tothe trunk.
The notch (Fig.16-C) should be deep enough to
create a hinge (Fig.16-F) of sufficient width and Fig. 16
strength. The notch should be wide enough to
direct the fall of the tree for as long as possible.
Use wooden or plastic wedges (Fig .17-A) to
prevent pinching the bar and chain (Fig.17-B) in the
cut. Wedges also control felling.
When diameter of wood being cut is greater than
the bar length, make 2 cuts as shown (Fig.18).
WARNING. Before making the final cut,
always recheck the area for bystanders,
animals or obstacles.
WARNING: Never saw completely Fig. 17
through the trunk. Always leave a hinge
(Fig.16-F). The hinge guides the tree. If
the trunk is completely cut through,
control over the felling direction is lost.
Insert a wedge or felling lever in the cut
well before the tree becomes unstable
and starts to move. This will prevent the
bar from binding in the felling cut if you
have misjudged the falling direction.
Make sure no bystanders have entered
the range of the falling tree before you
push it over.
WARNING: As the felling cut gets close Fig. 18
to the hinge, the tree should begin to fall.
When tree begins to fall, remove saw
from cut, stop engine, put chain saw
down, and leave area along retreat path.

15
 MAINTENANCE
WARNING. Use only original Remove the sprocket cover. Remove the bar and
manufacturer’s replacement parts, saw chain from unit.
accessories and attachments. Failure to
do so can cause possible injury, poor To replace the bar with a new one, loosen the
performance and may void your screw of the chain tension assembly. Mount the
warranty. chain tension assembly on to the new bar and
tighten the screw.
WARNING. Servicing requires extreme
care and knowledge and should be Put the new chain in the correct direction onto the
performed only by a qualified technician. bar and make sure that the drive links are aligned
For service we suggest you return the in the bar groove.
product to your nearest authorized Attach the bar to the chain saw and loop the chain
service center for repair. around the drive sprocket.
When servicing, use only identical
replacement parts. Replace the sprocket cover.

WARNING. Disconnect from the power Adjust the chain tension. Refer to the “Adjusting the
supply before adjustment, maintenance chain tension” section.
or cleaning. Failure to do so could result
WARNING. Improper chain sharpening
in serious personal injury.
increases the potential of kick-back.
• You may only make adjustments or repairs
WARNING. Failure to replace or repair a
described in this manual. For other repairs,
damaged chain can cause serious
contact the authorized service agent.
injury.
• Consequences of improper maintenance may
WARNING. The saw chain is very
cause the chain brake and other safety features
sharp. Always wear protective gloves
to not function correctly, thus increasing the
when performing maintenance to the
potential for serious injury. Keep your chainsaw
chain.
professionally maintained and safe.
INSPECTING AND CLEANING THE CHAIN
• Sharpening the chain safely is a skilled task.
BRAKE
Therefore the manufacturer strongly
Always keep the chain brake mechanism clean by
recommends that a worn or dull chain is
lightly brushing the linkage free from dirt.
replaced with a new one, available from your
authorised Ryobi service centre. Always test the chain brake performance after
cleaning.
• Follow instructions for lubricating and chain
tension checking and adjustment. Refer to “Operation - Checking and Operating
Chain Brake” on page 13 for additional information.
• After each use, clean the product with a soft dry
cloth.
• Check all nuts, bolts and screws at frequent
intervals for security to ensure the product is in
safe working condition. Any part that is
damaged should be properly repaired or
replaced by an authorized service centre.
REPLACING GUIDE BAR AND SAW CHAIN
Disconnect the product from its power supply. Wear
protective gloves.
Unscrew the guide bar locking knob by turning it
counterclockwise until the sprocket cover comes
loose.

16
 MAINTENANCE
SHARPENING THE CHAIN SAW
WARNING. We advise you to have deep
or important sharpening carried out by a
service agent who is equipped with an
electric sharpener.
When the chain penetrates into wood with difficulty,
it needs to be sharpened as follows:
1. Put the chain under tension.
2. Fasten the bar in a vice so that the chain can
slide (Fig.19)
3. File with forward strokes only until all the worn Fig. 20
out parts of the cutting edge is removed.
4. Count the number of strokes given to the cutter
as a reference basis and file away the same
number of strokes on all other cutters.
5. If after sharpening a few times, the depth
gauge protrudes from the template, you must
reset its level using a flat file. (Fig.20)
6. Finally round off the depth gauge. (Fig.21)
GUIDE BAR
The guide bar is subjected to especially severe
wear and tear at the nose and the bottom. To avoid
one-sided wear and tear, turn the guide bar over
every time you sharpen the chain. Fig. 21
1. When you have finished working, clean out the
groove and the oil passages, with a special
scraping hook. (Fig.22).
2. Periodically trim the sides of the rails using a
flat file. If not done in the long run the
“feathered edges” might break away and
damage the bar. (Fig.23)

Fig. 22

Fig. 19

Fig. 23

17
 MAINTENANCE
3. If one rail is higher than the other one, it is NOTE. The condition of the oil passages can be
necessary to make it even with a flat file and easily checked. If the passages are clear, the chain
then smooth them with a file or fine grain will automatically give off a spray of oil within
abrasive paper. (Fig.24) seconds of starting the saw. Your saw is equipped
with an automatic oiler system.
CHAIN TENSION
Check the chain tension frequently and adjust as
often as necessary to keep the chain snug on the
bar, if the chain is pulled down with the fingers at
the centre of the bar the gap between the chain
and the bar should be 3 to 4mm.
NEW CHAINS
A new chain will need to be readjusted after as few
as 5 cuts. This is normal during the break in period,
future adjustments will be required less often.
OIL PASSAGES
Oil passages on the bar should be cleaned to Fig. 24
ensure proper lubrication of the bar and chain
during operation.

MAINTENANCE SCHEDULE

Daily check
Power cable for damge Before each use
Bar lubrication Before each use
Chain tension Before each use and frequently
Chain sharpness Before each use, visual check
For damaged parts Before each use
For loose fasteners Before each use
Chain brake function Before each use
Inspect and clean
Bar Before each use
Complete saw After each use
Chain brake Every 5 hours of operation

SERVICE
Now that you have purchased your tool, should a need ever exist of repair or service, simply contact your
nearest Ryobi Authorised Service Centre or other qualified service organistion. Be sure to provide all
pertinent facts when you call or visit.

18
 SYMBOLS

Indicates danger, warning or caution. It means attention!!!

Safety Alert Symbol
Your safety is involved.
Read Your Operator's Your manual contains special messages to bring attention
Manual to potential safety concerns as well as operating and
servicing information. Please read all the information
carefully to ensure satisfaction and safe use.

Wear eye, hearing and Wear eye, hearing and head protection when operating
head protection this equipment.

Loose clothing alert Do not wear loose clothing or jewellery.

Safety Alert: Kickback Kickback is very dangerous and can result in serious
danger injury. Always follow the instructions in this manual to
reduce kickback.

Electric shock Remove plug from the mains immediately if cable is

precaution damaged or cut.

Wet conditions alert Do not expose to wet or damp conditions.

Two hands operation Always use two hands to operate the machine.

Gloves Wear non-slip, heavy-duty gloves.

Insulation Symbol Double insulated for additional protection.

Recycle Symbol Waste electrical products should not be disposed of with

household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling
advice.

CE Marking Conforms to relevant safety standards.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.

WARNING Indicates a potentially hazardous situation, which, if not avoided, could

result in death or serious injury.

CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result
in minor or moderate injury.

CAUTION (Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
19