SBL1030CT AND SBL1040CT

SCHOTTKY RECTIFIER
Reverse Voltage - 30 and 40 Volts Forward Current - 10.0 Amperes

FEATURES
TO-220AB ♦ Plastic package has Underwriters Laboratory
Flammability Classifications 94V-0
♦ Metal silicon junction, majority carrier conduction
0.185 (4.70)
0.415 (10.54) MAX.
0.175 (4.44)
0.370 (9.40)
0.360 (9.14) 0.154 (3.91)
0.148 (3.74)
DIA.
0.055 (1.39)
0.045 (1.14)
♦ Low power loss, high efficiency
0.113 (2.87)
♦ High current capability,
0.103 (2.62)
0.145 (3.68)
0.135 (3.43)
low forward voltage drop
0.560 (14.22) ♦ High surge capacity
♦ For use in low voltage, high frequency inverters, free
0.530 (13.46)
0.410 (10.41) 0.350 (8.89)
0.635 (16.13)
0.390 (9.91) 0.330 (8.38)

PIN
0.625 (15.87)
1.148 (29.16)
wheeling, and polarity protection applications
1 2 3 1.118 (28.40)
0.110 (2.79)
♦ Guardring for overvoltage protection
♦ High temperature soldering guaranteed:
0.160 (4.06)
0.100 (2.54)
0.140 (3.56)

0.560 (14.22)
0.530 (13.46)
250°C/10 seconds, 0.25" (6.35mm) from case

0.105 (2.67)
0.095 (2.41) 0.037 (0.94)
0.027 (0.68) 0.022 (0.56)
MECHANICAL DATA
0.014 (0.35)
0.105 (2.67)
0.095 (2.41)
Case: JEDEC TO-220AB molded plastic body
0.205 (5.20)
PIN 1 PIN 2
Terminals: Lead solderable per MIL-STD-750,
0.195 (4.95)

PIN 3 CASE
Method 2026
Polarity: As marked
Dimensions in inches and (millimeters) Mounting Position: Any
Mounting Torque: 5 in. - lbs max.
Weight: 0.08 ounce, 2.24 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS SBL1030CT SBL1040CT UNITS

Maximum repetitive peak reverse voltage VRRM 30 40 Volts

Maximum RMS voltage VRMS 21 28 Volts
Maximum DC blocking voltage VDC 30 40 Volts
Maximum average forward rectified current
at TC=95°C I(AV) 10.0 Amps
Peak forward surge current, 8.3ms single
half sine-wave superimposed on rated load IFSM 175.0 Amps
(JEDEC Method)
Maximum instantaneous forward voltage
per leg at 5.0A (NOTE 1) VF 0.55 Volts
Maximum instantaneous reverse current at TC=25°C 0.5
rated DC blocking voltage (NOTE 1) TC=100°C IR 50.0 mA
Typical thermal resistance (NOTE 2) RΘJC 3.0 °C/W
Operating and storage temperature range TJ, TSTG -40 to +125 °C

NOTES:
(1) Pulse test: 300µs pulse width, 1% duty cycle
(2) Thermal resistance from junction to case per leg

4/98
 RATINGS AND CHARACTERISTIC CURVES SBL1030CT AND SBL1040CT
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE
CURRENT
FIG. 1 - FORWARD CURRENT DERATING CURVE
12.5 300
TJ=TJ max.

PEAK FORWARD SURGE CURRENT,

AVERAGE FORWARD CURRENT,

RESISTIVE OR INDUCTIVE LOAD

8.3ms SINGLE HALF SINE-WAVE
250 (JEDEC Method)
10

200
AMPERES

7.5

AMPERES
150
5
100
2.5
50
0
0 50 100 150
0
CASE TEMPERATURE, °C 1 10 100
NUMBER OF CYCLES AT 60 HZ

FIG. 4 - TYPICAL REVERSE

CHARACTERISTICS PER LEG
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD 50
CHARACTERISTICS PER LEG
50

PULSE WIDTH = 300µs 10

INSTANTANEOUS FORWARD CURRENT,

1% DUTY CYCLE TJ=125°C

10 INSTANTANEOUS REVERSE CURRENT,
TJ=125°C

1
AMPERES

MILLIAMPERES

TJ=25°C
1
TJ=75°C

0.1
0.1

0.01
0.01 TJ=25°C
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
0.001
0 20 40 60 80 100
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %

FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG
TRANSICENTTHERMAL IMPEDANCE, °C/W

4,000 100
TJ = 25°C
JUNCTION CAPACITANCE, pF

f=1.0 MHz
Vsig=50mVp-p

1,000 10.0

1.0
1.0

100
0.1 1.0
1 10 100 0.1
0.01 0.1 1 10.0 100
REVERSE VOLTAGE, VOLTS
t, PULSE DURATION, sec.
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.