Introduction:

The proposed construction shall have a RCC framed structure with moment resistant connection with
lateral load resisting Elements (SMRF).The complete analysis is carried out for extreme loading
conditions based on Indian Standards. The detailed analysis is carried out using STAAD.ProV8i software.
The summary of the analysis is furnished in the subsequent sections.

As per the soil report the soil stratum consist of medium soil at the foundation level.

Design considerations :
LOADING STANDARDS

IS codes: IS 875(Part 1): 1987, IS 875(Part 2): 1987, IS 875(Part 3):

1987, IS 1893:2002, IS 2062, IS 456: 2000, IS 13920: 1993,
IS 1904, IS 2974, SP 16, SP 34
Number of Floors G+IV

Framing Special moment resisting frame (SMRF) in tune with

architectural requirements.
Dead Loads IS-875(Part-1) : 1987
Live Loads IS 875(Part-2) : 1987
IS:1893(Part 1) : 2002, zone factor Z = 0.16; ( Zone III),
Earthquake Load Importance factor =1.0, Response reduction factor R = 5 ,Type
of soil conditions Soft soil (type III)
Wind Loads IS 875(Part-3) : 1987
Software used STAAD. Pro V8i
Method of Analysis Dynamic Analysis
Limit state method using STAAD. Pro V8i software
Design Methodology confirming to IS 456 -2000
Reinforcements detailing IS: 456-2000, IS 13920: 1993

Material Specification
1) R.C.C
i) Minimum compressive strength : fcK = 20 Mpa
ii) Modulus of elasticity : Ec = 25000 Mpa
iii) Unit weight for concrete : wc = 25 kN/m3
iv) Poisson's ratio for concrete : μc = 0.15
v) Reinforcement steel
a) Minimum yield strength : fy = 500 Mpa
b) Modulus of elasticity : Es = 200000 Mpa
c) Diameters 8,10,12,16,20, mm
Design Load Cases:

1. DEAD LOAD (DL)

2. LIVE LOAD (LL)
3. WIND LOAD (WL)
4. EARTHQUAKE LOAD (EL)
Design Load Combination:

Load calculation
Unit weight , thickness, height etc. considered
1 ) Thickness of walls / parapet wall
a ) Outside Brickwork top of T/B to PL 200 mm
b ) Internal Wall top of T/B to PL 100 mm
c ) Outside Brickwork floor to floor 200 mm
d ) Internal Wall floor to floor 100 mm
e ) Parapet wall Over general roof 100 mm
f ) Parapet wall Over stair roof 100 mm
g ) Eq. Thickness for Balcony Wall 100 mm
2 ) Height of Masonary /Concrete works
a ) Ground level to plinth level 600 mm
b ) P.L. to 1st Stair Landing Level 1500 mm
c ) Plinth Level to 1st Floor Level 2400 mm
d ) Other Floor to Floor Level 3000 mm
e ) Roof Level to Stair Roof Level 2600 mm
3 ) Heights of parapet wall / Balcony Wall
a ) Over general roof 1000 mm
b ) Over stair roof 600 mm
c ) Balcony wall 1200 mm
4 ) % of Opening considered
a ) For outside wall 25%
b ) For internal wall 5%
c ) For Balcony 10%
d ) For Stair case window 50%
5 ) Overall thickness of slab
a ) Floor 125 mm
b ) Roof 125 mm
6 ) Finishing thickness of Floor / Roof treatment /Plaster
a ) Over Floor /Basement slab 50 mm
b ) Over Roof slab 75 mm
c ) Celing Plaster 10 mm
d ) Outside / Inside Wall Plaster (Av.) 15 mm

7 ) Unit weight of concrete / brick work etc.

a ) Reinforced Cement concrete 25 kN/m3
b ) For floor finishing 24 kN/m3
c ) For Roof treatment 22 kN/m3
d ) For Plaster Works 20 kN/m3
3
e ) Brick works 20 kN/m
8 ) Depth of beams ( For Calculation of Loads only)
a ) Outer beam (In General) 450 mm,450mm
b ) Inner beam (In General) 450 mm,450mm
General Loading Consideration (Dead Load and Live Load)
Loading from Masonary /Concrete wall works

A) 200 thk. wall on Beam Depth of Beam 450 mm

200 Thk. Solid wall 3.4 m high @ 0.6 t/m^3 = 0.37 T/m
25 Thk. Plaster 3.4 m high @ 2.1 t/m^3 = 0.18 T/m
For Solid wall 0.55 T/m
For 75% Solid wall 0.41 T/m

B) 125 thk. wall on Beam Depth of Beam 450 mm

125 Thk. Solid wall 3.4 m high @ 0.6 t/m^3 = 0.23 T/m
25 Thk. Plaster 3.4 m high @ 2.1 t/m^3 = 0.18 T/m

For Solid wall 0.41 T/m

For 90% Solid wall 0.37 T/m

C) 200 thk. wall on Beam Depth of Beam 450 mm

200 Thk. Solid wall 3.0 m high @ 0.6 t/m^3 = 0.33 T/m
25 Thk. Plaster 3.0 m high @ 2.1 t/m^3 = 0.16 T/m

For Solid wall 0.48 T/m

For 75% Solid wall 0.36 T/m

C) 125 thk. wall on Beam Depth of Beam 450 mm

125 Thk. Solid wall 3.0 m high @ 0.6 t/m^3 = 0.20 T/m
25 Thk. Plaster 3.0 m high @ 2.1 t/m^3 = 0.16 T/m

For Solid wall 0.36 T/m

For 90% Solid wall 0.33 T/m

ATTIC ROOM LOAD

E) 200 thk. wall on Beam Depth of Beam 450 mm

200 Thk. Solid wall 2.6 m high @ 0.6 t/m^3 = 0.27 T/m
25 Thk. Plaster 2.6 m high @ 2.1 t/m^3 = 0.14 T/m

For Solid wall 0.41 T/m

For 90% Solid wall 0.37 T/m

PARAPET WALL
F) 125 thk. wall on Beam Depth of Beam 0 mm

125 Thk. Solid wall 1.0 m high @ 0.6 t/m^3 = 0.08 T/m
25 Thk. Plaster 1.0 m high @ 2.1 t/m^3 = 0.05 T/m
For Solid wall 0.13 T/m
4.2.2 Imposed Gravity loads on floors
Imposed loads will be considered on the basis of IS: 875 Part‐2
Dead & Live Load pressure for slab is as follows:

SCHEDULE OF DEAD LOADS

(A) ROOF OR TERRACE LOAD :-

a) 50 thk.finish @ 2400 kg/m3= 0.12 t/m2

b) 50 thk.roof treatment @ 2200 kg/m3= 0.11 t/m2
c) 6 thk.ceilling plaster @ 2100 kg/m3= 0.01 t/m2
120 thk.roof slab @ 2500 kg/m3= 0.3 t/m2
135 thk.roof slab @ 2500 kg/m3= 0.34 t/m2
0.54 t/m2
Dead Load= 0.58 t/m2

(A) TYP. FLOOR LOAD :-

a) 50 thk.finish @ 2400 kg/m3= 0.12 t/m2

c) 6 thk.ceilling plaster @ 2100 kg/m3= 0.01 t/m2
d) Partition wall 0.1 t/m2
120 thk. slab @ 2500 kg/m3= 0.3 t/m2
135 thk. slab @ 2500 kg/m3= 0.34 t/m2
0.53 t/m2
Dead Load/ Floor Respectively= 0.57 t/m2

SCHEDULE OF LIVE LOADS ON ROOF

(A) FLOOR LOAD :-

Live load For all Office ,Kitchens,Toilet Bathrooms etc,

a) 2 kn/m2
@
b) Live load For Corridoor , Stair case , Balconies etc @ 3 kn/m2

(A) ROOF LOAD :-

a) Live Load for Acceassable Roof 1.5 kn/m2

b) Inacceassable Roof 0.75 kn/m2
CALCULATION OF WIND FORCES

REF: I.S. 875 (Part 3) -1987.

As per Clause 5.2 Appendix A

1) Basic wind speed (V) 50 m/s

LOCATION: W.B.

2) Design Wind speed

Vz= Vb * k1*k2*k3
a) K1= Probability factor (Risk Coefficient) as per TABLE1
(For probable design life of structure = 1

b) K2= Terrain, Height and Structure Size factor as per TABLE 2 = 1

As per clause 5.3.2 the structure is consider to be in

Terrain Category= 3
Class = B
Height of the building= 15 m

c) K3= Topography Factor as per Cl. 5.3.3

Since the Topography of the Site is Flat with slight undulations,
Factor considered as = 1
UPTO 10M
Vz= 50.0 m/s
Pz = 0.6*Vz2
= 1500.0 n/sqm
= 0.15 t/sqm
CALCULATION OF SEISMIC LOAD

Vb= Ah x W

= Z I Sa [ Zone factor, Z ]= 0.16 From Table-2[ Zone III ]

2R g [ Importance factor,I = 1 From Table-6
[ Response reduction factor,R = ] 5 From Table-7

Height of structure above base h = 15.00 m

Base dimensions of building d = 26 m
18 m
W = Seismic weight of the building as per clause 7.4.2

Fundamental Natural Period for frame building with brick infill panels.

Tax=(0.09h/d0.5)= 0.26 sec [As per Clause 7.6.2]

Sa/g= 2.5 depending upon T. [From Clause 6.4.5 for Type III soil]

Hence
Ahx= Z I Sa/2 R g = 0.04

Taz=(0.09h/d0.5)= 0.32 sec [As per Clause 7.6.2]

Sa/g= 2.5 depending upon T. [From Clause 6.4.5 for Type II soil]

Hence
Ahz= Z I Sa/2 R g = 0.04

Balcony Load 01

3.255 m
Beam A
Beam B

SLAB A
Slab B

Slab B

1.325 m

1.628 m

Area of Slab A= 2.16 Sqm.

Length of Beam A= 3 m

Area of Slab B= 1.08 Sqm.

Length of Beam A= 1.33 m

DL /m over Beam A= x2.16/3.255= 0 t/m

DL /m over Beam B= x1.08/1.33= 0 t/m

LL /m over Beam A= 0x2.16/3.255= 0 t/m

LL /m over Beam B= 0x1.08/1.33= 0 t/m

Balcony Load 02
 4.375 m
Beam A

Beam B SLAB A

Slab B

Slab B
1.325 m

2.188 m

Area of Slab A= 2.9 Sqm.

Length of Beam A= 4 m

Area of Slab B= 1.45 Sqm.

Length of Beam A= 1.33 m

DL /m over Beam A= x2.9/4.375= 0 t/m

DL /m over Beam B= x1.45/1.33= 0 t/m

LL /m over Beam A= 0x2.9/4.375= 0 t/m

LL /m over Beam B= 0x1.45/1.33= 0 t/m
 DESIGN CALCULATION OF STAIR CASE 1 ,TWER 2
1) TYP. STAIR LOAD :-

Weight of Each step per meter= 0.152x2.5x1x1/2= 0.19 t/m

Weight of waist slab per meter= (0.29258x0.15x1x2.5)/0.25= 0.44 t/m
Floor Finish= 0.1 t/m
2
Total Weight of Stair Per meter= 0.73 t/m= 730.00 kg/m
w= 250 mm

h= 152 mm
150 mm thk. Waist slab
292.58 mm
COLUMN
0
31
STAIR SECTION

DEAD LOAD
STAIR FLOOR LOAD= 730.00 kg/m^2
Length of Flight= 2.00 m 3.00 m
width of each flight= 1.325 m 1.5 m
Floor Finish=
Total floor load= 0.73 t/m^2
Length of landing= 1.3 m
Length of landing= 0.59 m 0.6 2.00 1.28
Width of Landing= 2.65 m
Width of Landing= 2.65 m
Thk. Of Landing= 0.15 m
Landing Load= 0.375 t/m^2
Floor Finish= 100 kg/m^2 1.325
Total floor load= 0.475 t/m^2

1.33

0.7 t/m^2
0.48
t/m^2
A B
2.00 m 1.28 m
Rb= 1.13 t/m Ra= 0.934 t/m

LIVE LOAD
Stair Load= 300 kn/m^2
0.3 t/m^2
0.3 t/m^2

A B
2.00 m 1.28 m
Rb= 0.49 t/m Ra= 0.49125 t/m
TWO WAY SLAB DESIGN
DESIGN PARAMETERS
Fy= 500 N/mm^2
Fck= 20 N/mm^2
Clear Cover= 20 mm

Load Calculation:-
Let us assume the depth of Slab Panel (S1) D = 120 mm dx = 96 mm dy = 88 mm
Let us assume the depth of Slab Panel (S2) D = 135 mm dx = 111 mm dy = 103 mm
Let us assume the depth of Slab Panel (S3) D = 120 mm dx = 96 mm dy = 88 mm
Let us assume the depth of Slab Panel (S4) D = 135 mm dx = 111 mm dy = 103 mm
Let us assume the depth of Slab Panel (S5) D = 120 mm dx = 96 mm dy = 88 mm

SLAB Edge
FLOOR Lx Ly Ly/Lx Loading
MKD. Condition Bending moment Bending Moment Limit state factored Moment
As per
2
IS 456- (w) Co-efficient M = α * w * lx Mu = 1.5M tm
2000.T-26
tm tm
m t/m2 αx- αx αy- αy Mx- Mx My- My Mux- Mux Muy- Muy
1st S1 3.535 4.533 1.3 Case no 4 0.74 0.065 0.049 0.047 0.035 0.60 0.453113 0.435 0.3237 0.9016 0.6797 0.6519 0.4855
1st S2 4.602 5.04 1.1 Case no 3 0.7775 0.044 0.033 0.037 0.028 0.72 0.543385 0.609 0.4611 1.0868 0.8151 0.9139 0.6916
1st S3 2.951 5.04 1.7 Case no 1 0.74 0.06 0.045 0.032 0.024 0.39 0.28999 0.206 0.1547 0.58 0.435 0.3093 0.232
1st S4 4.477 4.759 1.1 Case no 3 0.7775 0.044 0.033 0.037 0.028 0.69 0.514267 0.577 0.4363 1.0285 0.7714 0.8649 0.6545
1st S5 3.322 3.668 1.1 Case no 4 0.74 0.053 0.04 0.047 0.035 0.43 0.326656 0.384 0.2858 0.6492 0.49 0.5757 0.4287
9
FLOOR Dia of Dia of
Slab Ru = Mv/bd2 Pt Ast reqd. = Ptbd/100 Depth Bar. at Bar. at
2 2
MKD (N/mm ) As per SP 16 mm reqd. Depth supprt span
Rux- Rux Ruy - Ruy Ptx- Ptx Pty - Pty Astx- Astx Asty- Asty mm status mm mm
1st S1 0.9783 0.74 0.84 0.626909 0.245 0.181 0.206 0.156 235.2 173.76 181.3 137.28 57.79 OK 8 8
1st S2 0.882 0.66 0.86 0.651881 0.219 0.168 0.219 0.168 243.1 186.48 225.6 173.04 63.44 OK 8 8
1st S3 0.6293 0.47 0.4 0.299576 0.156 0.119 0.094 0.07 149.8 114.24 82.72 61.6 46.35 OK 8 8
1st S4 0.8348 0.63 0.82 0.616949 0.206 0.156 0.206 0.156 228.7 173.16 212.2 160.68 61.72 OK 8 8
1st S5 0.7045 0.53 0.74 0.553637 0.181 0.131 0.181 0.143 173.8 125.76 159.3 125.84 49.04 OK 8 8

Spacin Ast prov Ast prov Ast prov

Spacing g at τv=Vu
Ast prov at at at span. τc
SLAB along X- along support. Mod Deflectio Vu. /bd Shear
FLOOR span. along support. along y Pt prov.% fs dreqd. N/mm
MKD. X axis y-y along x Factor n KN N/mm Check
2 along y axis 2
(mm) axis axis x axis mm 2 2
2
(mm) 2 axis mm mm
mm
1st S1 140 140 358.86 358.86 358.86 358.86 0.37 190.07 1.7 80 OK 15.70 0.16 0.469 OK
1st S2 140 140 358.86 358.86 358.86 358.86 0.32 196.45 1.75 102 OK 21.47 0.19 0.429 OK
1st S3 140 140 358.86 358.86 358.86 358.86 0.37 121.02 2 57 OK 13.10 0.14 0.469 OK
1st S4 140 140 358.86 358.86 358.86 358.86 0.32 184.78 1.75 99 OK 20.89 0.19 0.429 OK
1st S5 140 140 358.86 358.86 358.86 358.86 0.37 140.42 2 64 OK 14.75 0.15 0.469 OK
ONE WAY SLAB DESIGN
DESIGN PARAMETERS
Fy= 500 N/mm^2
Fck= 20 N/mm^2
Clear Cover= 20 mm

Shear will be maximum at a distance of effective depth of slab from face of column or beam.

Overall Effective Max Max

SLAB Ly/ Dia of Total Max. Ast Ast τv=Vu/b Shear
FLOOR Lx Ly Condt. Depth, Depth, factored Mu/b Pt Spacing Pt prov. Vu. τc
MKD. Lx Bar. Load, B.M(M) reqd. prov. d Check
(D) (d) (Mu) d^2
m m mm mm mm t/m tm tm % mm2 mm c/c mm2 % Kn N/mm2 N/mm2
ONE
1st S1 1.225 3.654 2.983 120 8 92 0.64 0.12005 0.18008 0.21 0.07 64.4 140 358.86 0.39 3.14 0.03 0.482 OK
WAY

Distribution steel area = Minimum steel area = 0.12x(1000x120/100=

= 144 mm^2
Provide 8 mm diameter bar @ 140 mm c/c, Ast,provided = 358.86 Sqmm
Pt= 0.39 %
distribution bars are checked below:
For main bars (cl. 26.3.3.b.1 of IS 456), the maximum spacing is the lesser of 3d
and 300 mm i.e., 300 mm.
For distribution bars (cl. 26.3.3.b.2 of IS 456), the maximum spacing is the lesser of 5d
or 450 mm i.e., 450 mm. Provided
spacings, therefore, satisfy the requirements.
Maximum diameter of the bars (cl. 26.5.2.2 of IS 456) shall not exceed
120/8 = 15 mm is also satisfied with the bar diameters selected here.
Tower 2
STAIR DESIGN CALCULATION
No of Rise= 11
Number of treads in the flight= 10
Trade T= 250 mm
Rise R= 152 mm
Width of landing beams= 250 mm
Width of Half landing= 1275 mm
Grade of concrete M20
Fck= 20 N/mm^2)
Fy= 500 N/mm^2)

Effective span= 3866 mm

Assume waist slab Depth D= 150 mm

Effective depth d= 119 mm

LOAD CALCULATION

Weight of Each step per meter= 0.152x2.5x1x1/2= 0.19 t/m

Weight of waist slab per meter= (0.2926x0.15x1x2.5)/0.25= 0.44 t/m
Floor Finish= 0.1 t/m
Total Weight of Landing= 0.44+0.1= 0.54 t/m
2
Total Weight of Stair Per meter= 0.44+0.19+0.1= 0.73 t/m= 730 kg/m
w= 250 mm

h= 152 mm
150 mm thk. Waist slab

293 mm

STAIR SECTION

Live load= 0.3 t/m

0.84 t/m 1.03 t/m

1.28 m 2.59 m

Rb 1.50 m

Ra

Taking Moment about A

Rax3.87=(0.84x1.28x3.23)+(1.03x2.59x1.295)
Ra= 1.79 t
Rb= (0.84x1.28)+(1.03x2.59)-1.79
= 1.953 t
Moment will be maximum where Shear Force is Zero.
So, assume Shear Force is Zero at a distance 'X' from point A
Ra-(0.84x1.28)-(1.03x (X-1.28)= 0
X= 1.97 m from support A ,Shear Force is Zero.
Max Moment at a distane 1.97 m from point A=
M =Ra x1.97-(0.84x1.28x(1.97-0.64))-(1.03x(1.97-1.28)x(1.97-1.28)/2
M = 1.85 t m
Mu= 1.85x1.5= 2.775 t m

Check for depth of waist slab:

Mu
d=
2.66 x 1000
= 102.14 mm<119mm
Hence ok

Main reinforcements

Mu/bd^2= 1.96
According to SP-16 ,Table 4
Pt= 0.531
So, Ast required= 631.89 mm^/m
Provide 12 mm f bar @ 150 mm c/c
Ast provide= 753.6 mm^2 at main reinforcement
Hence ok

Distribution reinforcements
Destribution reinforcement= 0.12% of cross section
= 180 mm^2/m
Provide 8 mm f bar @ 200 mm c/c
Ast provide= 251.2 mm^2 at main reinforcement
Hence ok
 Thursday, March 27, 2025, 09:25 PM
PAGE NO. 1

****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.33 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAR 27, 2025 *
* Time= 21:25:10 *
* *
* USER ID: *
****************************************************

1. STAAD SPACE
INPUT FILE: D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.STD
2. START JOB INFORMATION
3. ENGINEER DATE 14-MAR-22
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER MTON
7. JOINT COORDINATES
8. 1 0 0 0; 2 3.507 0 0; 3 8.975 0 0; 4 0 0 3.322; 5 3.507 0 3.322
9. 6 8.975 0 3.322; 7 8.975 0 6.072; 8 0 0 7.647; 9 4.477 0 7.647
10. 10 5.877 0 7.647; 11 7.677 0 7.647; 12 4.477 0 9.422; 13 5.877 0 9.422
11. 14 7.677 0 9.422; 15 8.975 0 9.422; 16 0 0 12.406; 17 4.477 0 12.406
12. 18 8.975 0 12.406; 19 4.477 0 15.206; 20 8.975 0 15.206; 21 0.611 0 15.206
13. 22 8.975 0 17.479; 23 4.477 0 17.856; 24 0.611 0 17.856; 25 4.477 0 21.133
14. 26 8.975 0 21.133; 27 -0.784 0 21.133; 28 8.975 0 26.173; 29 -0.784 0 26.173
15. 30 2.751 0 26.173; 31 5.702 0 26.173; 32 8.975 0 29.673; 33 5.702 0 29.673
16. 34 -0.784 0 30.706; 35 2.751 0 30.706; 36 0 -1.5 0; 37 3.507 -1.5 0
17. 38 8.975 -1.5 0; 39 0 -1.5 3.322; 40 3.507 -1.5 3.322; 41 8.975 -1.5 3.322
18. 42 8.975 -1.5 6.072; 43 0 -1.5 7.647; 44 4.477 -1.5 7.647; 45 5.877 -1.5 7.647
19. 46 7.677 -1.5 7.647; 47 4.477 -1.5 9.422; 48 5.877 -1.5 9.422
20. 49 7.677 -1.5 9.422; 50 8.975 -1.5 9.422; 51 0 -1.5 12.406
21. 52 4.477 -1.5 12.406; 53 8.975 -1.5 12.406; 54 4.477 -1.5 15.206
22. 55 8.975 -1.5 15.206; 56 0.611 -1.5 15.206; 57 8.975 -1.5 17.479
23. 58 4.477 -1.5 17.856; 59 0.611 -1.5 17.856; 60 4.477 -1.5 21.133
24. 61 8.975 -1.5 21.133; 62 -0.784 -1.5 21.133; 63 8.975 -1.5 26.173
25. 64 -0.784 -1.5 26.173; 65 2.751 -1.5 26.173; 66 5.702 -1.5 26.173
26. 67 8.975 -1.5 29.673; 68 5.702 -1.5 29.673; 69 -0.784 -1.5 30.706
27. 70 2.751 -1.5 30.706; 71 0 3.4 0; 72 3.507 3.4 0; 73 8.975 3.4 0
28. 74 0 3.4 3.322; 75 3.507 3.4 3.322; 76 8.975 3.4 3.322; 77 8.975 3.4 6.072
29. 78 0 3.4 7.647; 79 4.477 3.4 7.647; 80 5.877 3.4 7.647; 81 7.677 3.4 7.647
30. 82 4.477 3.4 9.422; 83 5.877 3.4 9.422; 84 7.677 3.4 9.422; 85 8.975 3.4 9.422
31. 86 0 3.4 12.406; 87 4.477 3.4 12.406; 88 8.975 3.4 12.406; 89 4.477 3.4 15.206
32. 90 8.975 3.4 15.206; 91 0.611 3.4 15.206; 92 8.975 3.4 17.479
33. 93 4.477 3.4 17.856; 94 0.611 3.4 17.856; 95 4.477 3.4 21.133
34. 96 8.975 3.4 21.133; 97 -0.784 3.4 21.133; 98 8.975 3.4 26.173
35. 99 -0.784 3.4 26.173; 100 2.751 3.4 26.173; 101 5.702 3.4 26.173
36. 102 8.975 3.4 29.673; 103 5.702 3.4 29.673; 104 -0.784 3.4 30.706
37. 105 2.751 3.4 30.706; 106 10.075 3.4 0; 107 10.075 3.4 3.322
38. 108 10.075 3.4 6.072; 109 10.075 3.4 9.422; 110 6.407 3.4 0

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 1 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 2

39. 111 6.407 3.4 3.322; 112 3.507 3.4 7.647; 113 7.677 3.4 3.322
40. 114 7.677 3.4 6.072; 115 10.212 3.4 12.406; 116 10.212 3.4 15.206
41. 117 10.212 3.4 17.479; 118 10.304 3.4 21.133; 119 10.304 3.4 26.173
42. 120 10.175 3.4 26.173; 121 10.175 3.4 29.673; 122 10.075 3.4 12.406
43. 123 10.212 3.4 21.133; 124 0.611 3.4 12.406; 125 0.611 3.4 21.133
44. 126 4.477 3.4 17.479; 127 5.877 3.4 12.406; 128 5.877 3.4 15.206
45. 129 5.877 3.4 17.479; 130 5.702 3.4 21.133; 131 5.702 3.4 17.479
46. 132 2.751 3.4 29.673; 133 2.751 3.4 21.133; 134 -0.784 3.4 17.856
47. 135 0 6.425 0; 136 3.507 6.425 0; 137 8.975 6.425 0; 138 0 6.425 3.322
48. 139 3.507 6.425 3.322; 140 8.975 6.425 3.322; 141 8.975 6.425 6.072
49. 142 0 6.425 7.647; 143 4.477 6.425 7.647; 144 5.877 6.425 7.647
50. 145 7.677 6.425 7.647; 146 4.477 6.425 9.422; 147 5.877 6.425 9.422
51. 148 7.677 6.425 9.422; 149 8.975 6.425 9.422; 150 0 6.425 12.406
52. 151 4.477 6.425 12.406; 152 8.975 6.425 12.406; 153 4.477 6.425 15.206
53. 154 8.975 6.425 15.206; 155 0.611 6.425 15.206; 156 8.975 6.425 17.479
54. 157 4.477 6.425 17.856; 158 0.611 6.425 17.856; 159 4.477 6.425 21.133
55. 160 8.975 6.425 21.133; 161 -0.784 6.425 21.133; 162 8.975 6.425 26.173
56. 163 -0.784 6.425 26.173; 164 2.751 6.425 26.173; 165 5.702 6.425 26.173
57. 166 8.975 6.425 29.673; 167 5.702 6.425 29.673; 168 -0.784 6.425 30.706
58. 169 2.751 6.425 30.706; 170 10.075 6.425 0; 171 10.075 6.425 3.322
59. 172 10.075 6.425 6.072; 173 10.075 6.425 9.422; 174 6.407 6.425 0
60. 175 6.407 6.425 3.322; 176 3.507 6.425 7.647; 177 7.677 6.425 3.322
61. 178 7.677 6.425 6.072; 179 10.212 6.425 12.406; 180 10.212 6.425 15.206
62. 181 10.212 6.425 17.479; 182 10.304 6.425 21.133; 183 10.304 6.425 26.173
63. 184 10.175 6.425 26.173; 185 10.175 6.425 29.673; 186 10.075 6.425 12.406
64. 187 10.212 6.425 21.133; 188 0.611 6.425 12.406; 189 0.611 6.425 21.133
65. 190 4.477 6.425 17.479; 191 5.877 6.425 12.406; 192 5.877 6.425 15.206
66. 193 5.877 6.425 17.479; 194 5.702 6.425 21.133; 195 5.702 6.425 17.479
67. 196 2.751 6.425 29.673; 197 2.751 6.425 21.133; 198 -0.784 6.425 17.856
68. 199 0 9.45 0; 200 3.507 9.45 0; 201 8.975 9.45 0; 202 0 9.45 3.322
69. 203 3.507 9.45 3.322; 204 8.975 9.45 3.322; 205 8.975 9.45 6.072
70. 206 0 9.45 7.647; 207 4.477 9.45 7.647; 208 5.877 9.45 7.647
71. 209 7.677 9.45 7.647; 210 4.477 9.45 9.422; 211 5.877 9.45 9.422
72. 212 7.677 9.45 9.422; 213 8.975 9.45 9.422; 214 0 9.45 12.406
73. 215 4.477 9.45 12.406; 216 8.975 9.45 12.406; 217 4.477 9.45 15.206
74. 218 8.975 9.45 15.206; 219 0.611 9.45 15.206; 220 8.975 9.45 17.479
75. 221 4.477 9.45 17.856; 222 0.611 9.45 17.856; 223 4.477 9.45 21.133
76. 224 8.975 9.45 21.133; 225 -0.784 9.45 21.133; 226 8.975 9.45 26.173
77. 227 -0.784 9.45 26.173; 228 2.751 9.45 26.173; 229 5.702 9.45 26.173
78. 230 8.975 9.45 29.673; 231 5.702 9.45 29.673; 232 -0.784 9.45 30.706
79. 233 2.751 9.45 30.706; 234 10.075 9.45 0; 235 10.075 9.45 3.322
80. 236 10.075 9.45 6.072; 237 10.075 9.45 9.422; 238 6.407 9.45 0
81. 239 6.407 9.45 3.322; 240 3.507 9.45 7.647; 241 7.677 9.45 3.322
82. 242 7.677 9.45 6.072; 243 10.212 9.45 12.406; 244 10.212 9.45 15.206
83. 245 10.212 9.45 17.479; 246 10.304 9.45 21.133; 247 10.304 9.45 26.173
84. 248 10.175 9.45 26.173; 249 10.175 9.45 29.673; 250 10.075 9.45 12.406
85. 251 10.212 9.45 21.133; 252 0.611 9.45 12.406; 253 0.611 9.45 21.133
86. 254 4.477 9.45 17.479; 255 5.877 9.45 12.406; 256 5.877 9.45 15.206
87. 257 5.877 9.45 17.479; 258 5.702 9.45 21.133; 259 5.702 9.45 17.479
88. 260 2.751 9.45 29.673; 261 2.751 9.45 21.133; 262 -0.784 9.45 17.856
89. 263 0 12.475 0; 264 3.507 12.475 0; 265 8.975 12.475 0; 266 0 12.475 3.322
90. 267 3.507 12.475 3.322; 268 8.975 12.475 3.322; 269 8.975 12.475 6.072
91. 270 0 12.475 7.647; 271 4.477 12.475 7.647; 272 5.877 12.475 7.647
92. 273 7.677 12.475 7.647; 274 4.477 12.475 9.422; 275 5.877 12.475 9.422
93. 276 7.677 12.475 9.422; 277 8.975 12.475 9.422; 278 0 12.475 12.406
94. 279 4.477 12.475 12.406; 280 8.975 12.475 12.406; 281 4.477 12.475 15.206

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 2 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 3

95. 282 8.975 12.475 15.206; 283 0.611 12.475 15.206; 284 8.975 12.475 17.479
96. 285 4.477 12.475 17.856; 286 0.611 12.475 17.856; 287 4.477 12.475 21.133
97. 288 8.975 12.475 21.133; 289 -0.784 12.475 21.133; 290 8.975 12.475 26.173
98. 291 -0.784 12.475 26.173; 292 2.751 12.475 26.173; 293 5.702 12.475 26.173
99. 294 8.975 12.475 29.673; 295 5.702 12.475 29.673; 296 -0.784 12.475 30.706
100. 297 2.751 12.475 30.706; 298 10.075 12.475 0; 299 10.075 12.475 3.322
101. 300 10.075 12.475 6.072; 301 10.075 12.475 9.422; 302 6.407 12.475 0
102. 303 6.407 12.475 3.322; 304 3.507 12.475 7.647; 305 7.677 12.475 3.322
103. 306 7.677 12.475 6.072; 307 10.212 12.475 12.406; 308 10.212 12.475 15.206
104. 309 10.212 12.475 17.479; 310 10.304 12.475 21.133; 311 10.304 12.475 26.173
105. 312 10.175 12.475 26.173; 313 10.175 12.475 29.673; 314 10.075 12.475 12.406
106. 315 10.212 12.475 21.133; 316 0.611 12.475 12.406; 317 0.611 12.475 21.133
107. 318 4.477 12.475 17.479; 319 5.877 12.475 12.406; 320 5.877 12.475 15.206
108. 321 5.877 12.475 17.479; 322 5.702 12.475 21.133; 323 5.702 12.475 17.479
109. 324 2.751 12.475 29.673; 325 2.751 12.475 21.133; 326 -0.784 12.475 17.856
110. 327 0 15.5 0; 328 3.507 15.5 0; 329 8.975 15.5 0; 330 0 15.5 3.322
111. 331 3.507 15.5 3.322; 332 8.975 15.5 3.322; 333 8.975 15.5 6.072
112. 334 0 15.5 7.647; 335 4.477 15.5 7.647; 336 5.877 15.5 7.647
113. 337 7.677 15.5 7.647; 338 4.477 15.5 9.422; 339 5.877 15.5 9.422
114. 340 7.677 15.5 9.422; 341 8.975 15.5 9.422; 342 0 15.5 12.406
115. 343 4.477 15.5 12.406; 344 8.975 15.5 12.406; 345 4.477 15.5 15.206
116. 346 8.975 15.5 15.206; 347 0.611 15.5 15.206; 348 8.975 15.5 17.479
117. 349 4.477 15.5 17.856; 350 0.611 15.5 17.856; 351 4.477 15.5 21.133
118. 352 8.975 15.5 21.133; 353 -0.784 15.5 21.133; 354 8.975 15.5 26.173
119. 355 -0.784 15.5 26.173; 356 2.751 15.5 26.173; 357 5.702 15.5 26.173
120. 358 8.975 15.5 29.673; 359 5.702 15.5 29.673; 360 -0.784 15.5 30.706
121. 361 2.751 15.5 30.706; 362 10.075 15.5 0; 363 10.075 15.5 3.322
122. 364 10.075 15.5 6.072; 365 10.075 15.5 9.422; 366 6.407 15.5 0
123. 367 6.407 15.5 3.322; 368 3.507 15.5 7.647; 369 7.677 15.5 3.322
124. 370 7.677 15.5 6.072; 371 10.212 15.5 12.406; 372 10.212 15.5 15.206
125. 373 10.212 15.5 17.479; 374 10.304 15.5 21.133; 375 10.304 15.5 26.173
126. 376 10.175 15.5 26.173; 377 10.175 15.5 29.673; 378 10.075 15.5 12.406
127. 379 10.212 15.5 21.133; 380 0.611 15.5 12.406; 381 0.611 15.5 21.133
128. 382 4.477 15.5 17.479; 383 5.877 15.5 12.406; 384 5.877 15.5 15.206
129. 385 5.877 15.5 17.479; 386 5.702 15.5 21.133; 387 5.702 15.5 17.479
130. 388 2.751 15.5 29.673; 389 2.751 15.5 21.133; 390 -0.784 15.5 17.856
131. 391 4.477 18.1 15.206; 392 0.611 18.1 15.206; 393 4.477 18.1 17.856
132. 394 0.611 18.1 17.856; 395 5.877 18.1 15.206; 396 5.877 18.1 17.856
133. 397 5.877 17 7.647; 398 7.677 17 7.647; 399 5.877 17 9.422; 400 7.677 17 9.422
134. 401 4.477 17 7.647; 402 4.477 17 9.422; 404 7.677 19.6 7.647
135. 406 7.677 19.6 9.422; 407 4.477 19.6 7.647; 408 4.477 19.6 9.422
136. 409 0.611 1.7 15.206; 410 0.611 1.7 17.856; 411 0.611 4.913 15.206
137. 412 0.611 4.913 17.856; 413 0.611 7.938 15.206; 414 0.611 7.938 17.856
138. 415 0.611 10.963 15.206; 416 0.611 10.963 17.856; 417 0.611 13.988 15.206
139. 418 0.611 13.988 17.856
140. MEMBER INCIDENCES
141. 1 1 36; 2 2 37; 3 3 38; 4 4 39; 5 5 40; 6 6 41; 7 7 42; 8 8 43; 9 9 44
142. 11 11 46; 12 12 47; 15 15 50; 16 16 51; 17 17 52; 18 18 53; 19 19 54; 20 20 55
143. 21 21 56; 22 22 57; 23 23 58; 24 24 59; 25 25 60; 26 26 61; 27 27 62; 28 28 63
144. 29 29 64; 30 30 65; 31 31 66; 32 32 67; 33 33 68; 34 34 69; 35 35 70; 36 1 71
145. 37 2 72; 38 3 73; 39 4 74; 40 5 75; 41 6 76; 42 7 77; 43 8 78; 44 9 79
146. 46 11 81; 47 12 82; 50 15 85; 51 16 86; 52 17 87; 53 18 88; 54 19 89; 55 20 90
147. 56 21 409; 57 22 92; 58 23 93; 59 24 410; 60 25 95; 61 26 96; 62 27 97
148. 63 28 98; 64 29 99; 65 30 100; 66 31 101; 67 32 102; 68 33 103; 69 34 104
149. 70 35 105; 71 71 72; 72 72 110; 73 74 75; 74 75 111; 75 76 77; 76 78 112
150. 77 79 80; 78 80 81; 79 82 83; 80 83 84; 81 84 85; 82 86 124; 83 87 127

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 3 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 4

151. 84 91 89; 85 89 128; 86 94 93; 87 97 125; 88 95 130; 89 99 100; 90 100 101

152. 91 101 98; 92 104 105; 93 103 102; 94 88 90; 95 90 92; 96 92 96; 97 71 74
153. 98 74 78; 99 78 86; 100 72 75; 101 79 82; 102 82 87; 103 87 89; 104 89 126
154. 105 93 95; 106 80 83; 107 81 84; 108 97 99; 109 99 104; 110 100 132
155. 111 101 103; 112 73 106; 113 76 107; 114 77 108; 115 85 109; 116 106 107
156. 117 107 108; 118 108 109; 119 110 73; 120 111 113; 121 110 111; 122 112 79
157. 123 75 112; 124 113 76; 125 81 114; 126 114 113; 127 77 114; 128 88 122
158. 129 90 116; 130 92 117; 131 115 116; 132 116 117; 133 96 123; 134 98 120
159. 135 120 119; 136 120 121; 137 102 121; 138 118 119; 139 122 115; 140 109 122
160. 141 123 118; 142 117 123; 143 124 87; 144 91 124; 146 125 133; 147 94 125
161. 148 126 93; 149 92 129; 150 127 88; 151 83 127; 152 128 90; 153 127 128
162. 154 129 131; 155 128 129; 156 130 96; 157 101 130; 158 131 126; 159 130 131
163. 160 132 105; 161 103 132; 162 133 95; 163 100 133; 164 97 134; 165 134 94
164. 166 135 136; 167 136 174; 168 138 139; 169 139 175; 170 140 141; 171 142 176
165. 172 143 144; 173 144 145; 174 146 147; 175 147 148; 176 148 149; 177 150 188
166. 178 151 191; 179 155 153; 180 153 192; 181 158 157; 182 161 189; 183 159 194
167. 184 163 164; 185 164 165; 186 165 162; 187 168 169; 188 167 166; 189 152 154
168. 190 154 156; 191 156 160; 192 135 138; 193 138 142; 194 142 150; 195 136 139
169. 196 143 146; 197 146 151; 198 151 153; 199 153 190; 200 157 159; 201 144 147
170. 202 145 148; 203 161 163; 204 163 168; 205 164 196; 206 165 167; 207 137 170
171. 208 140 171; 209 141 172; 210 149 173; 211 170 171; 212 171 172; 213 172 173
172. 214 174 137; 215 175 177; 216 174 175; 217 176 143; 218 139 176; 219 177 140
173. 220 145 178; 221 178 177; 222 141 178; 223 152 186; 224 154 180; 225 156 181
174. 226 179 180; 227 180 181; 228 160 187; 229 162 184; 230 184 183; 231 184 185
175. 232 166 185; 233 182 183; 234 186 179; 235 173 186; 236 187 182; 237 181 187
176. 238 188 151; 239 155 188; 241 189 197; 242 158 189; 243 190 157; 244 156 193
177. 245 191 152; 246 147 191; 247 192 154; 248 191 192; 249 193 195; 250 192 193
178. 251 194 160; 252 165 194; 253 195 190; 254 194 195; 255 196 169; 256 167 196
179. 257 197 159; 258 164 197; 259 161 198; 260 198 158; 261 199 200; 262 200 238
180. 263 202 203; 264 203 239; 265 204 205; 266 206 240; 267 207 208; 268 208 209
181. 269 210 211; 270 211 212; 271 212 213; 272 214 252; 273 215 255; 274 219 217
182. 275 217 256; 276 222 221; 277 225 253; 278 223 258; 279 227 228; 280 228 229
183. 281 229 226; 282 232 233; 283 231 230; 284 216 218; 285 218 220; 286 220 224
184. 287 199 202; 288 202 206; 289 206 214; 290 200 203; 291 207 210; 292 210 215
185. 293 215 217; 294 217 254; 295 221 223; 296 208 211; 297 209 212; 298 225 227
186. 299 227 232; 300 228 260; 301 229 231; 302 201 234; 303 204 235; 304 205 236
187. 305 213 237; 306 234 235; 307 235 236; 308 236 237; 309 238 201; 310 239 241
188. 311 238 239; 312 240 207; 313 203 240; 314 241 204; 315 209 242; 316 242 241
189. 317 205 242; 318 216 250; 319 218 244; 320 220 245; 321 243 244; 322 244 245
190. 323 224 251; 324 226 248; 325 248 247; 326 248 249; 327 230 249; 328 246 247
191. 329 250 243; 330 237 250; 331 251 246; 332 245 251; 333 252 215; 334 219 252
192. 336 253 261; 337 222 253; 338 254 221; 339 220 257; 340 255 216; 341 211 255
193. 342 256 218; 343 255 256; 344 257 259; 345 256 257; 346 258 224; 347 229 258
194. 348 259 254; 349 258 259; 350 260 233; 351 231 260; 352 261 223; 353 228 261
195. 354 225 262; 355 262 222; 356 263 264; 357 264 302; 358 266 267; 359 267 303
196. 360 268 269; 361 270 304; 362 271 272; 363 272 273; 364 274 275; 365 275 276
197. 366 276 277; 367 278 316; 368 279 319; 369 283 281; 370 281 320; 371 286 285
198. 372 289 317; 373 287 322; 374 291 292; 375 292 293; 376 293 290; 377 296 297
199. 378 295 294; 379 280 282; 380 282 284; 381 284 288; 382 263 266; 383 266 270
200. 384 270 278; 385 264 267; 386 271 274; 387 274 279; 388 279 281; 389 281 318
201. 390 285 287; 391 272 275; 392 273 276; 393 289 291; 394 291 296; 395 292 324
202. 396 293 295; 397 265 298; 398 268 299; 399 269 300; 400 277 301; 401 298 299
203. 402 299 300; 403 300 301; 404 302 265; 405 303 305; 406 302 303; 407 304 271
204. 408 267 304; 409 305 268; 410 273 306; 411 306 305; 412 269 306; 413 280 314
205. 414 282 308; 415 284 309; 416 307 308; 417 308 309; 418 288 315; 419 290 312
206. 420 312 311; 421 312 313; 422 294 313; 423 310 311; 424 314 307; 425 301 314

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 4 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 5

207. 426 315 310; 427 309 315; 428 316 279; 429 283 316; 431 317 325; 432 286 317
208. 433 318 285; 434 284 321; 435 319 280; 436 275 319; 437 320 282; 438 319 320
209. 439 321 323; 440 320 321; 441 322 288; 442 293 322; 443 323 318; 444 322 323
210. 445 324 297; 446 295 324; 447 325 287; 448 292 325; 449 289 326; 450 326 286
211. 451 327 328; 452 328 366; 453 330 331; 454 331 367; 455 332 333; 456 334 368
212. 457 335 336; 458 336 337; 459 338 339; 460 339 340; 461 340 341; 462 342 380
213. 463 343 383; 464 347 345; 465 345 384; 466 350 349; 467 353 381; 468 351 386
214. 469 355 356; 470 356 357; 471 357 354; 472 360 361; 473 359 358; 474 344 346
215. 475 346 348; 476 348 352; 477 327 330; 478 330 334; 479 334 342; 480 328 331
216. 481 335 338; 482 338 343; 483 343 345; 484 345 382; 485 349 351; 486 336 339
217. 487 337 340; 488 353 355; 489 355 360; 490 356 388; 491 357 359; 492 329 362
218. 493 332 363; 494 333 364; 495 341 365; 496 362 363; 497 363 364; 498 364 365
219. 499 366 329; 500 367 369; 501 366 367; 502 368 335; 503 331 368; 504 369 332
220. 505 337 370; 506 370 369; 507 333 370; 508 344 378; 509 346 372; 510 348 373
221. 511 371 372; 512 372 373; 513 352 379; 514 354 376; 515 376 375; 516 376 377
222. 517 358 377; 518 374 375; 519 378 371; 520 365 378; 521 379 374; 522 373 379
223. 523 380 343; 524 347 380; 525 347 350; 526 381 389; 527 350 381; 528 382 349
224. 529 348 385; 530 383 344; 531 339 383; 532 384 346; 533 383 384; 534 385 387
225. 535 384 385; 536 386 352; 537 357 386; 538 387 382; 539 386 387; 540 388 361
226. 541 359 388; 542 389 351; 543 356 389; 544 353 390; 545 390 350; 546 71 135
227. 547 72 136; 548 73 137; 549 74 138; 550 75 139; 551 76 140; 552 77 141
228. 553 78 142; 554 79 143; 556 81 145; 557 82 146; 560 85 149; 561 86 150
229. 562 87 151; 563 88 152; 564 89 153; 565 90 154; 566 91 411; 567 92 156
230. 568 93 157; 569 94 412; 570 95 159; 571 96 160; 572 97 161; 573 98 162
231. 574 99 163; 575 100 164; 576 101 165; 577 102 166; 578 103 167; 579 104 168
232. 580 105 169; 581 135 199; 582 136 200; 583 137 201; 584 138 202; 585 139 203
233. 586 140 204; 587 141 205; 588 142 206; 589 143 207; 591 145 209; 592 146 210
234. 595 149 213; 596 150 214; 597 151 215; 598 152 216; 599 153 217; 600 154 218
235. 601 155 413; 602 156 220; 603 157 221; 604 158 414; 605 159 223; 606 160 224
236. 607 161 225; 608 162 226; 609 163 227; 610 164 228; 611 165 229; 612 166 230
237. 613 167 231; 614 168 232; 615 169 233; 616 199 263; 617 200 264; 618 201 265
238. 619 202 266; 620 203 267; 621 204 268; 622 205 269; 623 206 270; 624 207 271
239. 626 209 273; 627 210 274; 630 213 277; 631 214 278; 632 215 279; 633 216 280
240. 634 217 281; 635 218 282; 636 219 415; 637 220 284; 638 221 285; 639 222 416
241. 640 223 287; 641 224 288; 642 225 289; 643 226 290; 644 227 291; 645 228 292
242. 646 229 293; 647 230 294; 648 231 295; 649 232 296; 650 233 297; 651 263 327
243. 652 264 328; 653 265 329; 654 266 330; 655 267 331; 656 268 332; 657 269 333
244. 658 270 334; 659 271 335; 661 273 337; 662 274 338; 665 277 341; 666 278 342
245. 667 279 343; 668 280 344; 669 281 345; 670 282 346; 671 283 417; 672 284 348
246. 673 285 349; 674 286 418; 675 287 351; 676 288 352; 677 289 353; 678 290 354
247. 679 291 355; 680 292 356; 681 293 357; 682 294 358; 683 295 359; 684 296 360
248. 685 297 361; 686 345 391; 687 347 392; 688 349 393; 689 350 394; 690 392 391
249. 691 392 394; 692 394 393; 693 391 393; 694 391 395; 695 393 396; 696 395 396
250. 697 336 397; 698 337 398; 699 339 399; 700 340 400; 701 397 398; 702 399 400
251. 703 397 399; 704 398 400; 705 335 401; 706 338 402; 707 401 397; 708 402 399
252. 709 401 402; 711 398 404; 713 400 406; 714 401 407; 715 402 408; 716 407 404
253. 718 408 406; 720 407 408; 722 404 406; 723 1 2; 724 2 3; 725 4 5; 726 5 6
254. 727 8 9; 728 9 10; 729 10 11; 730 12 13; 731 13 14; 732 14 15; 733 16 17
255. 734 17 18; 735 21 19; 736 19 20; 737 24 23; 738 23 22; 739 27 25; 740 25 26
256. 741 29 30; 742 30 31; 743 31 28; 744 33 32; 745 34 35; 746 3 6; 747 6 7
257. 748 7 15; 749 15 18; 750 18 20; 751 20 22; 752 22 26; 753 26 28; 754 28 32
258. 755 1 4; 756 4 8; 757 8 16; 758 16 21; 759 21 24; 760 24 27; 761 27 29
259. 762 29 34; 763 2 5; 764 5 9; 765 9 12; 766 10 13; 767 11 14; 768 7 11
260. 769 12 17; 770 17 19; 771 19 23; 772 23 25; 773 30 35; 774 31 33; 775 35 33
261. 776 25 30; 777 25 31; 778 409 91; 779 410 94; 780 409 410; 781 411 155
262. 782 412 158; 783 413 219; 784 414 222; 785 415 283; 786 416 286; 787 417 347

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 5 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 6

263. 788 418 350; 789 411 412; 790 413 414; 791 415 416; 792 417 418; 815 11 15
264. 816 339 275; 817 336 272; 818 13 48; 819 83 13; 820 147 83; 821 211 147
265. 822 275 211; 823 10 45; 824 80 10; 825 144 80; 826 208 144; 827 272 208
266. ELEMENT INCIDENCES SHELL
267. 793 14 49 48 13; 794 13 48 45 10; 795 10 11 46 45; 796 11 14 49 46
268. 797 80 81 11 10; 798 81 84 14 11; 799 84 14 13 83; 800 144 145 81 80
269. 801 145 148 84 81; 802 148 84 83 147; 803 208 209 145 144; 804 209 212 148 145
270. 805 212 148 147 211; 806 272 273 209 208; 807 273 276 212 209
271. 808 276 212 211 275; 809 336 337 273 272; 810 337 340 276 273
272. 811 340 276 275 339; 812 397 398 337 336; 813 398 400 340 337
273. 814 400 340 339 399
274. START GROUP DEFINITION
275. FLOOR
276. _TYP_120_NO_WL 71 73 80 81 84 86 90 95 TO 97 100 103 105 110 TO 113 115 116 -
277. 119 TO 121 124 128 TO 130 132 140 143 144 146 147 149 TO 152 154 TO 156 159 -
278. 161 162 166 168 175 176 179 181 185 190 TO 192 195 198 200 205 TO 208 210 -
279. 211 214 TO 216 219 223 TO 225 227 235 238 239 241 242 244 TO 247 249 TO 251 -
280. 254 256 257 261 263 270 271 274 276 280 285 TO 287 290 293 295 300 TO 303 -
281. 305 306 309 TO 311 314 318 TO 320 322 330 333 334 336 337 339 TO 342 344 -
282. 345 TO 346 349 351 352 356 358 365 366 369 371 375 380 TO 382 385 388 390 -
283. 395 TO 398 400 401 404 TO 406 409 413 TO 415 417 425 428 429 431 432 434 -
284. 435 TO 437 439 TO 441 444 446 447
285. _TYP_120_WALL 72 TO 74 76 81 89 91 TO 93 98 100 107 109 TO 111 114 115 118 -
286. 121 123 125 127 134 TO 137 160 167 TO 169 171 176 184 186 TO 188 193 195 -
287. 202 204 TO 206 209 210 213 216 218 220 222 229 TO 232 255 262 TO 264 266 -
288. 271 279 281 TO 283 288 290 297 299 TO 301 304 305 308 311 313 315 317 324 -
289. 325 TO 327 350 357 TO 359 361 366 374 376 TO 378 383 385 392 394 TO 396 399 -
290. 400 403 406 408 410 412 419 TO 422 445
291. _TYP_135_WALL 76 82 91 99 101 102 122 133 TO 135 138 141 143 156 157 171 177 -
292. 186 194 196 197 217 228 TO 230 233 236 238 251 252 266 272 281 289 291 292 -
293. 312 323 TO 325 328 331 333 346 347 361 367 376 384 386 387 407 418 TO 420 -
294. 423 426 428 441 442
295. _TYP_120_ONE_WL 75 87 96 113 114 117 124 126 127 130 133 141 142 147 164 165 -
296. 170 182 191 208 209 212 219 221 222 225 228 236 237 242 259 260 265 277 286 -
297. 303 304 307 314 316 317 320 323 331 332 337 354 355 360 372 381 398 399 402 -
298. 409 411 412 415 418 426 427 432 449 450
299. _TYP_ONE_LIVCOR 79 83 85 88 94 102 103 105 128 129 131 139 148 151 153 158 -
300. 159 174 178 180 183 189 197 198 200 223 224 226 234 243 246 248 253 254 269 -
301. 273 275 278 284 292 293 295 318 319 321 329 338 341 343 348 349 364 368 370 -
302. 373 379 387 388 390 413 414 416 424 433 436 438 443 444
303. _ROOF_135 456 462 471 479 481 482 502 513 TO 515 518 521 523 536 537
304. _ROOF_120 451 TO 454 456 TO 461 464 TO 467 469 TO 478 480 481 483 TO 486 488 -
305. 489 TO 493 495 496 499 TO 506 508 TO 510 512 514 516 517 520 523 524 526 527 -
306. 529 TO 536 538 TO 543
307. _ROOF1_120 461 468 470 487 494 495 498 505 507 537 542 543
308. _ROOF_120_ONE 455 459 463 465 467 468 474 476 482 483 485 493 494 497 504 -
309. 506 TO 511 513 519 521 522 527 528 531 533 534 538 539 544 545
310. _LIFT_MECHINE 701 TO 704 707 TO 709
311. _ROOF_120_INACCB 690 TO 696 716 718 720 722
312. _TYP_120_LIVCOR 74 77 TO 79 85 87 TO 90 94 101 104 106 108 120 122 123 125 -
313. 126 146 150 152 TO 155 157 158 162 163 169 172 TO 174 180 182 TO 185 189 -
314. 196 199 201 203 215 217 218 220 221 241 245 247 TO 250 252 253 257 258 264 -
315. 267 TO 269 275 277 TO 280 284 291 294 296 298 310 312 313 315 316 336 340 -
316. 342 TO 345 347 348 352 353 359 362 TO 364 370 372 TO 375 379 386 389 391 -
317. 393 405 407 408 410 411 431 435 437 TO 440 442 443 447 448
318. END GROUP DEFINITION

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 6 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 7

319. ELEMENT PROPERTY

320. 793 TO 814 THICKNESS 0.15
321. DEFINE MATERIAL START
322. ISOTROPIC CONCRETE
323. E 2.21467E+006
324. POISSON 0.17
325. DENSITY 2.40262
326. ALPHA 1E-005
327. DAMP 0.05
328. TYPE CONCRETE
329. STRENGTH FCU 2812.28
330. END DEFINE MATERIAL
331. MEMBER PROPERTY AMERICAN
332. 1 3 4 6 TO 9 11 15 16 18 TO 24 27 29 32 36 38 39 41 TO 44 46 50 51 53 TO 59 -
333. 62 64 67 546 548 549 551 TO 554 556 560 561 563 TO 569 571 572 574 577 581 -
334. 583 584 586 TO 589 591 595 596 598 TO 604 606 607 609 612 616 618 619 621 -
335. 622 TO 624 626 630 631 633 TO 639 641 642 644 647 651 653 654 656 TO 659 661 -
336. 665 666 668 TO 674 676 677 679 682 686 TO 689 698 705 711 714 778 779 781 -
337. 782 TO 788 PRIS YD 0.45 ZD 0.25
338. 2 12 17 31 33 TO 35 37 47 52 66 68 TO 70 547 550 557 562 575 576 578 TO 580 -
339. 582 585 592 597 610 611 613 TO 615 617 620 627 632 645 646 648 TO 650 652 -
340. 655 662 667 680 681 683 TO 685 706 715 PRIS YD 0.25 ZD 0.45
341. 71 TO 144 146 TO 239 241 TO 334 336 TO 429 431 TO 545 690 TO 696 701 TO 704 -
342. 707 TO 709 716 718 720 722 TO 777 780 789 TO 792 815 PRIS YD 0.45 ZD 0.25
343. 700 713 PRIS YD 0.25 ZD 0.25
344. MEMBER PROPERTY AMERICAN
345. 697 699 816 TO 827 PRIS YD 0.05 ZD 0.05
346. MEMBER PROPERTY AMERICAN
347. 5 40 PRIS YD 0.25 ZD 0.5
348. 26 28 61 63 573 608 643 678 PRIS YD 0.5 ZD 0.25
349. 25 60 570 605 640 675 PRIS YD 0.6 ZD 0.25
350. 30 65 PRIS YD 0.25 ZD 0.5
351. CONSTANTS
352. MATERIAL CONCRETE ALL
353. SUPPORTS
354. 36 TO 70 FIXED
355. MEMBER RELEASE
356. 116 121 131 136 138 211 216 226 231 233 306 311 321 326 328 401 406 416 421 -
357. 423 496 501 511 516 518 START MY MZ
358. 107 121 123 126 136 138 140 142 144 147 155 158 159 161 163 164 202 216 218 -
359. 221 231 233 235 237 239 242 250 253 254 256 258 259 297 311 313 316 326 328 -
360. 330 332 334 337 345 348 349 351 353 354 392 406 408 411 421 423 425 427 429 -
361. 432 440 443 444 446 448 449 487 501 503 506 516 518 520 522 524 527 535 538 -
362. 539 541 543 544 END MY MZ
363. DEFINE 1893 LOAD
364. ZONE 0.16 RF 5 I 1 SS 2 ST 1 DM 0.05
365. SELFWEIGHT 1
366. JOINT WEIGHT
367. 392 394 WEIGHT 1.3
368. 392 394 WEIGHT 1.3
369. MEMBER WEIGHT
370. 690 692 CON 1.3 2.1
371. 690 692 CON 1.3 2.1
372. MEMBER WEIGHT
373. 735 737 754 759 762 UNI 0.55
374. 736 738 753 761 780 UNI 0.41

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 7 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 8

375. 739 740 773 774 UNI 0.41

376. 744 745 775 TO 777 UNI 0.37
377. 84 86 112 137 160 179 181 207 232 255 274 276 302 327 350 369 371 397 422 -
378. 445 UNI 0.48
379. 71 92 93 97 TO 99 108 109 116 TO 119 132 136 138 140 142 161 166 187 188 192 -
380. 193 TO 194 203 204 211 TO 214 227 231 233 235 237 256 261 282 283 287 TO 289 -
381. 298 299 306 TO 309 322 326 328 330 332 351 356 377 378 382 TO 384 393 394 -
382. 401 TO 404 417 421 423 425 427 446 789 TO 792 UNI 0.36
383. 73 82 87 102 103 105 110 111 113 TO 115 121 122 127 TO 130 133 TO 135 139 -
384. 141 146 149 151 154 155 159 164 168 177 182 197 198 200 205 206 208 TO 210 -
385. 216 217 222 TO 225 228 TO 230 234 236 241 244 246 249 250 254 259 263 272 -
386. 277 292 293 295 300 301 303 TO 305 311 312 317 TO 320 323 TO 325 329 331 -
387. 336 339 341 344 345 349 354 358 367 372 387 388 390 395 396 398 TO 400 406 -
388. 407 412 TO 415 418 TO 420 424 426 431 434 436 439 440 444 449 UNI 0.36
389. 77 81 89 TO 91 94 96 100 101 120 123 124 126 143 144 147 150 153 156 157 162 -
390. 163 172 176 184 TO 186 189 191 195 196 215 218 219 221 238 239 242 245 248 -
391. 251 252 257 258 267 271 279 TO 281 284 286 290 291 310 313 314 316 333 334 -
392. 337 340 343 346 347 352 353 362 366 374 TO 376 379 381 385 386 405 408 409 -
393. 411 428 429 432 435 438 441 442 447 448 UNI 0.33
394. 72 131 165 167 226 260 262 321 355 357 416 450 TO 452 462 472 473 477 TO 479 -
395. 488 489 492 496 TO 499 511 512 515 TO 522 524 540 541 544 545 690 TO 692 -
396. 694 TO 696 716 718 720 722 UNI 0.13
397. 457 464 466 535 701 702 704 707 TO 709 UNI 0.41
398. 465 481 525 538 UNI 0.37
399. 104 199 294 389 484 771 UNI 1.15
400. 780 789 TO 792 UNI 0.95
401. 104 199 294 389 484 771 UNI 0.5
402. 780 789 TO 792 UNI 0.5
403. FLOOR WEIGHT
**NOTE** about Floor/OneWay Loads/Weights.
Please note that depending on the shape of the floor you may
have to break up the FLOOR/ONEWAY LOAD into multiple commands.
For details please refer to Technical Reference Manual
Section 5.32.4.2 Note d and/or "5.32.4.3 Note f.

404. _TYP_120_NO_WL FLOAD 0.43

405. _TYP_120_WALL FLOAD 0.53
406. _TYP_135_WALL FLOAD 0.57
407. _TYP_120_LIVCOR FLOAD 0.43
408. _ROOF_135 FLOAD 0.58
409. _ROOF_120 FLOAD 0.54
410. _ROOF1_120 FLOAD 0.54
411. _LIFT_MECHINE FLOAD 0.54
412. _ROOF_120_INACCB FLOAD 0.54
413. _TYP_120_NO_WL FLOAD 0.2
414. _TYP_120_WALL FLOAD 0.2
415. _TYP_135_WALL FLOAD 0.2
416. _TYP_120_LIVCOR FLOAD 0.3
417. *_ROOF_135 FLOAD 0.05
418. *_ROOF_120 FLOAD 0.05
419. *_ROOF1_120 FLOAD 0.05
420. _LIFT_MECHINE FLOAD 1
421. *_ROOF_120_INACCB FLOAD 0.05
422. ONEWAY LOAD
423. _TYP_120_ONE_WL ONE 0.53 GX
424. _TYP_ONE_LIVCOR ONE 0.43 GX

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 8 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 9

425. _ROOF_120_ONE ONE 0.54 GX

426. _TYP_120_ONE_WL ONE 0.2 GX
427. _TYP_ONE_LIVCOR ONE 0.3 GX
428. DEFINE WIND LOAD

*** NOTE: If any floor diaphragm is present in the model Wind Load definition
should be defined after Floor Diaphragm definition. Otherwise wind
load generation may be unsuccessful during analysis.

429. TYPE 1 WIND 1

430. INT 0.15 HEIG 20
431. EXP 1 JOINT 1 TO 402 404 406 TO 418
432. *_ROOF_120_ONE ONE 0.05 GX
433. LOAD 1 LOADTYPE SEISMIC TITLE SL + X
434. 1893 LOAD X 1
435. LOAD 2 LOADTYPE SEISMIC TITLE SL - X
436. 1893 LOAD X -1.
437. LOAD 3 LOADTYPE SEISMIC TITLE SL + Z
438. 1893 LOAD Z 1
439. LOAD 4 LOADTYPE SEISMIC TITLE SL - Z
440. 1893 LOAD Z -1.
441. LOAD 5 LOADTYPE DEAD TITLE DL
442. SELFWEIGHT Y -1
443. JOINT LOAD
444. 392 394 FY -1.3
445. MEMBER LOAD
446. 690 692 CON GY -1.3 2.1
447. MEMBER LOAD
448. 735 737 754 759 762 UNI GY -0.55
449. 736 738 753 761 780 UNI GY -0.41
450. 739 740 773 774 UNI GY -0.41
451. 744 745 775 TO 777 UNI GY -0.37
452. 84 86 112 137 160 179 181 207 232 255 274 276 302 327 350 369 371 397 422 -
453. 445 UNI GY -0.48
454. 71 92 93 97 TO 99 108 109 116 TO 119 132 136 138 140 142 161 166 187 188 192 -
455. 193 TO 194 203 204 211 TO 214 227 231 233 235 237 256 261 282 283 287 TO 289 -
456. 298 299 306 TO 309 322 326 328 330 332 351 356 377 378 382 TO 384 393 394 -
457. 401 TO 404 417 421 423 425 427 446 789 TO 792 UNI GY -0.36
458. 73 82 87 102 103 105 110 111 113 TO 115 121 122 127 TO 130 133 TO 135 139 -
459. 141 146 149 151 154 155 159 164 168 177 182 197 198 200 205 206 208 TO 210 -
460. 216 217 222 TO 225 228 TO 230 234 236 241 244 246 249 250 254 259 263 272 -
461. 277 292 293 295 300 301 303 TO 305 311 312 317 TO 320 323 TO 325 329 331 -
462. 336 339 341 344 345 349 354 358 367 372 387 388 390 395 396 398 TO 400 406 -
463. 407 412 TO 415 418 TO 420 424 426 431 434 436 439 440 444 449 UNI GY -0.36

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 9 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 10

464. 77 81 89 TO 91 94 96 100 101 120 123 124 126 143 144 147 150 153 156 157 162 -
465. 163 172 176 184 TO 186 189 191 195 196 215 218 219 221 238 239 242 245 248 -
466. 251 252 257 258 267 271 279 TO 281 284 286 290 291 310 313 314 316 333 334 -
467. 337 340 343 346 347 352 353 362 366 374 TO 376 379 381 385 386 405 408 409 -
468. 411 428 429 432 435 438 441 442 447 448 UNI GY -0.33
469. 72 131 165 167 226 260 262 321 355 357 416 450 TO 452 462 472 473 477 TO 479 -
470. 488 489 492 496 TO 499 511 512 515 TO 522 524 540 541 544 545 690 TO 692 -
471. 694 TO 696 716 718 720 722 UNI GY -0.13
472. 457 464 466 535 701 702 704 707 TO 709 UNI GY -0.41
473. 465 481 525 538 UNI GY -0.37
474. 104 199 294 389 484 771 UNI GY -1.15
475. 780 789 TO 792 UNI GY -0.95
476. FLOOR LOAD
477. _TYP_120_NO_WL FLOAD -0.43 GY
478. _TYP_120_WALL FLOAD -0.53 GY
479. _TYP_135_WALL FLOAD -0.57 GY
480. _TYP_120_LIVCOR FLOAD -0.43 GY
481. _ROOF_135 FLOAD -0.58 GY
482. _ROOF_120 FLOAD -0.54 GY
483. _ROOF1_120 FLOAD -0.54 GY
484. _LIFT_MECHINE FLOAD -0.54 GY
485. _ROOF_120_INACCB FLOAD -0.54 GY
486. ONEWAY LOAD
487. _TYP_120_ONE_WL ONE -0.53 GY
488. _TYP_ONE_LIVCOR ONE -0.43 GY
489. _ROOF_120_ONE ONE -0.54 GY
490. LOAD 6 LOADTYPE LIVE TITLE LL
491. JOINT LOAD
492. 392 394 FY -1.3
493. MEMBER LOAD
494. 690 692 CON GY -1.3 2.1
495. MEMBER LOAD
496. 104 199 294 389 484 771 UNI GY -0.5
497. 780 789 TO 792 UNI GY -0.5
498. FLOOR LOAD
499. _TYP_120_NO_WL FLOAD -0.2 GY
500. _TYP_120_WALL FLOAD -0.2 GY
501. _TYP_135_WALL FLOAD -0.2 GY
502. _TYP_120_LIVCOR FLOAD -0.3 GY
503. _ROOF_135 FLOAD -0.15 GY
504. _ROOF_120 FLOAD -0.15 GY
505. _ROOF1_120 FLOAD -0.15 GY
506. _LIFT_MECHINE FLOAD -1 GY
507. _ROOF_120_INACCB FLOAD -0.075 GY
508. ONEWAY LOAD

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 10 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 11

509. _TYP_120_ONE_WL ONE -0.2 GY

510. _TYP_ONE_LIVCOR ONE -0.3 GY
511. _ROOF_120_ONE ONE -0.15 GY
512. LOAD 7 LOADTYPE WIND TITLE WL + X
513. WIND LOAD X 1 TYPE 1 YR 0 20
514. LOAD 8 LOADTYPE WIND TITLE WL - X
515. WIND LOAD X -1 TYPE 1 YR 0 20
516. LOAD 9 LOADTYPE WIND TITLE WL + Z
517. WIND LOAD Z 1 TYPE 1 YR 0 20
**WARNING-fx fy fz wind forces: 0.0000E+00 0.0000E+00 9.9960E-02
at coordinates: 0.0000E+00 3.4000E+00 2.6173E+01 ignored.
**WARNING-fx fy fz wind forces: 0.0000E+00 0.0000E+00 9.9960E-02
at coordinates: 0.0000E+00 0.0000E+00 2.6173E+01 ignored.
518. LOAD 10 LOADTYPE WIND TITLE WL - Z
519. WIND LOAD Z -1 TYPE 1 YR 0 20
**WARNING-fx fy fz wind forces: 0.0000E+00 0.0000E+00 -1.1003E-01
at coordinates: 3.5070E+00 0.0000E+00 2.1133E+01 ignored.
**WARNING-fx fy fz wind forces: 0.0000E+00 0.0000E+00 -1.5619E-01
at coordinates: 5.7020E+00 0.0000E+00 2.1133E+01 ignored.
**WARNING-fx fy fz wind forces: 0.0000E+00 0.0000E+00 -1.5823E-01
at coordinates: 2.7510E+00 0.0000E+00 2.1133E+01 ignored.
**WARNING-fx fy fz wind forces: 0.0000E+00 0.0000E+00 -1.3896E-01
at coordinates: 5.7020E+00 1.2475E+01 1.5206E+01 ignored.
**WARNING-fx fy fz wind forces: 0.0000E+00 0.0000E+00 -1.3896E-01
at coordinates: 5.7020E+00 1.5500E+01 1.5206E+01 ignored.
520. LOAD COMB 11 DL+LL
521. 5 1.5 6 1.5
522. LOAD COMB 12 DL+LL+WL
523. 5 1.2 6 1.2 7 1.2
524. LOAD COMB 13 DL+LL+WL-X
525. 5 1.2 6 1.2 8 1.2
526. LOAD COMB 14 DL+LL+WL+Z
527. 5 1.2 6 1.2 9 1.2
528. LOAD COMB 15 DL+LL+WL-Z
529. 5 1.2 6 1.2 10 1.2
530. LOAD COMB 16 DL+LL+SL+X
531. 5 1.2 6 1.2 1 1.2
532. LOAD COMB 17 DL+LL+SL-X
533. 2 1.2 5 1.2 6 1.2
534. LOAD COMB 18 DL+LL+SL+Z
535. 3 1.2 5 1.2 6 1.2

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 11 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 12

536. LOAD COMB 19 DL+LL+SL-Z

537. 5 1.2 6 1.2 4 1.2
538. LOAD COMB 20 DL+SL+X
539. 1 1.5 5 1.5
540. LOAD COMB 21 DL+SL-X
541. 5 1.5 2 1.5
542. LOAD COMB 22 DL+SL+Z
543. 3 1.5 5 1.5
544. LOAD COMB 23 DL+SL-Z
545. 5 1.5 4 1.5
546. LOAD COMB 24 DL+WL+X
547. 7 1.5 5 1.5
548. LOAD COMB 25 DL+WL-X
549. 5 1.5 8 1.5
550. LOAD COMB 26 DL+WL+Z
551. 5 1.5 9 1.5
552. LOAD COMB 27 DL+WL-X
553. 5 1.5 10 1.5
554. LOAD COMB 28 DL+LL
555. 5 1.0 6 0.6
556. LOAD COMB 29 DL+LL+WL
557. 5 1.0 6 0.6 7 1.0
558. LOAD COMB 30 DL+LL+WL-X
559. 5 1.0 6 0.6 8 1.0
560. LOAD COMB 31 DL+LL+WL+Z
561. 5 1.0 6 0.6 9 1.0
562. LOAD COMB 32 DL+LL+WL-Z
563. 5 1.0 6 0.6 10 1.0
564. LOAD COMB 33 DL+LL+SL+X
565. 5 1.0 1 1.0 6 0.6
566. LOAD COMB 34 DL+LL+SL-X
567. 2 1.0 5 1.0 6 0.6
568. LOAD COMB 35 DL+LL+SL+Z
569. 3 1.0 5 1.0 6 0.6
570. LOAD COMB 36 DL+LL+SL-Z
571. 5 1.0 6 0.6 4 1.0
572. LOAD COMB 37 DL+SL+X
573. 1 1.0 5 1.0
574. LOAD COMB 38 DL+SL-X
575. 5 1.0 2 1.0
576. LOAD COMB 39 DL+SL+Z
577. 3 1.0 5 1.0
578. LOAD COMB 40 DL+SL-Z
579. 5 1.0 4 1.0
580. LOAD COMB 41 DL+WL+X
581. 7 1.0 5 1.0
582. LOAD COMB 42 DL+WL-X
583. 5 1.0 8 1.0
584. LOAD COMB 43 DL+WL+Z
585. 5 1.0 9 1.0
586. LOAD COMB 44 DL+WL-Z
587. 5 1.0 10 1.0
588. PERFORM ANALYSIS

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 12 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 13

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS 416 NUMBER OF MEMBERS 778

NUMBER OF PLATES 22 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 35

SOLVER USED IS THE OUT-OF-CORE BASIC SOLVER

ORIGINAL/FINAL BAND-WIDTH= 386/ 44/ 246 DOF

TOTAL PRIMARY LOAD CASES = 10, TOTAL DEGREES OF FREEDOM = 2286
TOTAL LOAD COMBINATION CASES = 34 SO FAR.
SIZE OF STIFFNESS MATRIX = 563 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 19.8/ 236254.3 MB

**WARNING: IF THIS UBC/IBC ANALYSIS HAS TENSION/COMPRESSION

OR REPEAT LOAD OR RE-ANALYSIS OR SELECT OPTIMIZE, THEN EACH
UBC/IBC CASE SHOULD BE FOLLOWED BY PERFORM ANALYSIS CHANGE.

*********************************************************
* *
* TIME PERIOD FOR X 1893 LOADING = 0.73837 SEC *
* SA/G PER 1893= 1.842, LOAD FACTOR= 1.000 *
* VB PER 1893= 0.0295 X 1996.96= 58.85 MTON *
* *
*********************************************************

*********************************************************
* *
* TIME PERIOD FOR X 1893 LOADING = 0.73837 SEC *
* SA/G PER 1893= 1.842, LOAD FACTOR=-1.000 *
* VB PER 1893= 0.0295 X 1996.96= -58.85 MTON *
* *
*********************************************************

*********************************************************
* *
* TIME PERIOD FOR Z 1893 LOADING = 0.73837 SEC *
* SA/G PER 1893= 1.842, LOAD FACTOR= 1.000 *
* VB PER 1893= 0.0295 X 1996.96= 58.85 MTON *
* *
*********************************************************

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 13 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 14

*********************************************************
* *
* TIME PERIOD FOR Z 1893 LOADING = 0.73837 SEC *
* SA/G PER 1893= 1.842, LOAD FACTOR=-1.000 *
* VB PER 1893= 0.0295 X 1996.96= -58.85 MTON *
* *
*********************************************************

589. LOAD LIST 11 TO 27

590. START CONCRETE DESIGN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 14 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 15

591. CODE INDIAN

592. UNIT MMS NEWTON
593. CLEAR 40 MEMB 1 TO 9 11 12 15 TO 44 46 47 50 TO 70 546 TO 554 556 557 560 -
594. 561 TO 589 591 592 595 TO 624 626 627 630 TO 659 661 662 665 TO 689 -
595. 697 TO 700 705 706 711 713 TO 715 778 779 781 TO 788 816 TO 827
596. CLEAR 25 MEMB 71 TO 144 146 TO 239 241 TO 334 336 TO 429 431 TO 545 -
597. 690 TO 696 701 TO 704 707 TO 709 716 718 720 722 TO 777 780 789 TO 792 815
598. FC 20 ALL
599. FYMAIN 500 ALL
600. FYSEC 500 ALL
601. MAXMAIN 16 ALL
602. MAXSEC 10 ALL
603. MINMAIN 12 ALL
604. MINSEC 8 ALL
605. DESIGN BEAM 71 TO 144 146 TO 239 241 TO 334 336 TO 429 431 TO 545 690 TO 696 -
606. 701 TO 704 707 TO 709 716 718 720 722 TO 777 780 789 TO 792 815

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 15 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 16

============================================================================
B E A M N O. 71 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3507.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 876.7 mm 1753.5 mm 2630.2 mm 3507.0 mm
----------------------------------------------------------------------------
TOP 290.34 178.08 178.08 178.08 267.27
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 0.00

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 876.7 mm 1753.5 mm 2630.2 mm 3507.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 2-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = 32.13 MX = 0.35 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -38.53 MX = 0.29 LD= 24
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 72 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2900.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 16 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 17

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 725.0 mm 1450.0 mm 2175.0 mm 2900.0 mm
----------------------------------------------------------------------------
TOP 364.67 178.08 0.00 0.00 0.00
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 229.21 322.21

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 725.0 mm 1450.0 mm 2175.0 mm 2900.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 2-16í 2-16í 2-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 542.0 mm AWAY FROM START SUPPORT

VY = 52.07 MX = 0.75 LD= 11
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 73 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3507.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 876.7 mm 1753.5 mm 2630.2 mm 3507.0 mm
----------------------------------------------------------------------------
TOP 310.37 178.08 0.00 178.08 322.28
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 0.00

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 17 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 18

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 876.7 mm 1753.5 mm 2630.2 mm 3507.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 2-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = 28.22 MX = -2.19 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -49.74 MX = -0.26 LD= 24
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 74 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2900.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 725.0 mm 1450.0 mm 2175.0 mm 2900.0 mm
----------------------------------------------------------------------------
TOP 539.76 178.08 0.00 0.00 0.00
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 346.73 452.13

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 18 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 19

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 725.0 mm 1450.0 mm 2175.0 mm 2900.0 mm
----------------------------------------------------------------------------
TOP 5-12í 3-12í 2-12í 2-12í 2-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 4-12í 4-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 80.19 MX = 0.88 LD= 11
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 75 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2750.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 687.5 mm 1375.0 mm 2062.5 mm 2750.0 mm
----------------------------------------------------------------------------
TOP 183.10 178.08 0.00 178.08 226.25
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 187.14 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 687.5 mm 1375.0 mm 2062.5 mm 2750.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 19 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 20

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 29.20 MX = 1.07 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -33.71 MX = 2.87 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 76 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3507.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 876.7 mm 1753.5 mm 2630.2 mm 3507.0 mm
----------------------------------------------------------------------------
TOP 370.65 178.08 0.00 0.00 0.00
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 209.35 233.63 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 876.7 mm 1753.5 mm 2630.2 mm 3507.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 2-16í 2-16í 2-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 642.0 mm AWAY FROM START SUPPORT

VY = 56.16 MX = 0.86 LD= 11
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 20 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 21

============================================================================
B E A M N O. 77 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1400.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 273.44 178.08 178.08 291.34 524.70
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 236.78 178.08 178.08 178.08 223.18

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 5-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = -83.70 MX = 1.28 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 444.0 mm AWAY FROM END SUPPORT

VY = -93.13 MX = 1.28 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 78 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1800.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 21 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 22

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 450.0 mm 900.0 mm 1350.0 mm 1800.0 mm
----------------------------------------------------------------------------
TOP 178.08 178.08 178.08 178.08 178.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 450.0 mm 900.0 mm 1350.0 mm 1800.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 444.0 mm AWAY FROM START SUPPORT

VY = 28.25 MX = -0.04 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM END SUPPORT

VY = 21.16 MX = -0.04 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 79 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1400.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 178.08 178.08 178.08 302.18 529.21
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 270.26 178.08 178.08 178.08 229.50

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 22 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 23

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 5-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = -89.95 MX = -0.81 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 444.0 mm AWAY FROM END SUPPORT

VY = -93.15 MX = -0.81 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 80 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1800.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 450.0 mm 900.0 mm 1350.0 mm 1800.0 mm
----------------------------------------------------------------------------
TOP 242.26 178.08 178.08 178.08 232.82
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 185.13 178.08 178.08 178.08 188.04

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 23 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 24

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 450.0 mm 900.0 mm 1350.0 mm 1800.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 444.0 mm AWAY FROM START SUPPORT

VY = 42.06 MX = 2.20 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 81 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1298.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 324.5 mm 649.0 mm 973.5 mm 1298.0 mm
----------------------------------------------------------------------------
TOP 409.95 246.79 178.08 195.78 358.84
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 199.99 178.08 178.08 178.08 187.03

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 324.5 mm 649.0 mm 973.5 mm 1298.0 mm
----------------------------------------------------------------------------
TOP 4-12í 3-12í 3-12í 3-12í 4-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 24 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 25

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM END SUPPORT

VY = 71.86 MX = -1.67 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

*** WARNING:LENGTH TO DEPTH RATIO FOR MEMBER 82 IS LESS THAN 2.5.

DEEP BEAM IS NOT DESIGNED. ASSUMING IT TO BE A PART OF A
CONTINUOUS BEAM AND AWAY FROM THE CRITICAL SECTION FOR
ENHANCED SHEAR, ORDINARY SHEAR CHECK IS PERFORMED.,
OTHERWISE PROVIDE ENSH AND RENSH PARAMETERS ***

============================================================================
B E A M N O. 82 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 611.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 152.8 mm 305.5 mm 458.2 mm 611.0 mm
----------------------------------------------------------------------------
TOP 487.00 403.96 326.44 253.93 186.02
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 152.8 mm 305.5 mm 458.2 mm 611.0 mm
----------------------------------------------------------------------------
TOP 5-12í 4-12í 3-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = -30.89 MX = -2.77 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 25 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 26

============================================================================
B E A M N O. 83 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1400.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 405.88 266.42 180.42 178.08 0.00
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 178.08 219.92

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 4-12í 3-12í 3-12í 3-12í 2-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 38.55 MX = -10.60 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 84 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3866.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 26 of 612

 Thursday, March 27, 2025, 09:25 PM
STAAD SPACE -- PAGE NO. 27

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 966.5 mm 1933.0 mm 2899.5 mm 3866.0 mm
----------------------------------------------------------------------------
TOP 428.50 178.08 0.00 178.08 452.20
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 205.92 197.03 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 966.5 mm 1933.0 mm 2899.5 mm 3866.0 mm
----------------------------------------------------------------------------
TOP 4-12í 3-12í 2-12í 3-12í 4-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = 46.02 MX = -0.97 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM END SUPPORT

VY = -51.89 MX = -0.88 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 85 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1400.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 604.54 351.15 211.45 178.08 0.00
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 206.55 260.25

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 27 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 28

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 350.0 mm 700.0 mm 1050.0 mm 1400.0 mm
----------------------------------------------------------------------------
TOP 6-12í 4-12í 3-12í 3-12í 2-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = 80.27 MX = -2.51 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 86 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3866.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 966.5 mm 1933.0 mm 2899.5 mm 3866.0 mm
----------------------------------------------------------------------------
TOP 539.93 178.08 0.00 184.36 566.99
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 261.28 227.41 178.08 223.56 258.09

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 966.5 mm 1933.0 mm 2899.5 mm 3866.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 2-16í 3-16í 3-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 28 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 29

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 642.0 mm AWAY FROM START SUPPORT

VY = 56.97 MX = 1.30 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 642.0 mm AWAY FROM END SUPPORT

VY = -56.96 MX = 2.69 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 87 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1395.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 348.8 mm 697.5 mm 1046.2 mm 1395.0 mm
----------------------------------------------------------------------------
TOP 810.31 406.81 325.69 178.07 0.00
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 177.23 177.23 177.23 270.57 339.52

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 348.8 mm 697.5 mm 1046.2 mm 1395.0 mm
----------------------------------------------------------------------------
TOP 8-12í 4-12í 3-12í 3-12í 2-12í
REINF. 2 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-16í 3-16í 3-16í 3-16í 3-16í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 637.2 mm AWAY FROM START SUPPORT

VY = 84.11 MX = 1.11 LD= 11
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 29 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 30

============================================================================
B E A M N O. 88 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1225.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 306.2 mm 612.5 mm 918.8 mm 1225.0 mm
----------------------------------------------------------------------------
TOP 1108.71 762.08 417.84 189.28 0.00
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 349.76 178.08 228.08 371.46 523.93

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 306.2 mm 612.5 mm 918.8 mm 1225.0 mm
----------------------------------------------------------------------------
TOP 10-12í 7-12í 4-12í 3-12í 2-12í
REINF. 2 layer(s) 2 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 4-12í 3-12í 3-12í 4-12í 5-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 140 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 708.2 mm AWAY FROM START SUPPORT

VY = 117.79 MX = -11.75 LD= 23
Provide 2 Legged 8í @ 125 mm c/c

============================================================================

============================================================================
B E A M N O. 89 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3535.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 30 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 31

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 883.8 mm 1767.5 mm 2651.2 mm 3535.0 mm
----------------------------------------------------------------------------
TOP 538.81 180.77 0.00 178.08 406.78
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 307.18 298.71 182.58 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 883.8 mm 1767.5 mm 2651.2 mm 3535.0 mm
----------------------------------------------------------------------------
TOP 5-12í 3-12í 2-12í 3-12í 4-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = 58.20 MX = 0.76 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -65.68 MX = 0.18 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 90 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2951.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 737.7 mm 1475.5 mm 2213.2 mm 2951.0 mm
----------------------------------------------------------------------------
TOP 249.74 178.08 0.00 178.08 281.77
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 31 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 32

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 737.7 mm 1475.5 mm 2213.2 mm 2951.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 37.35 MX = -0.04 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -40.55 MX = 1.02 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 91 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3273.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 818.3 mm 1636.5 mm 2454.8 mm 3273.0 mm
----------------------------------------------------------------------------
TOP 319.42 178.08 178.08 368.74 925.31
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 213.58 178.08 178.08 193.27 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 32 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 33

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 818.3 mm 1636.5 mm 2454.8 mm 3273.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 3-16í 3-16í 5-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 542.0 mm AWAY FROM START SUPPORT

VY = 53.84 MX = -1.26 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 667.0 mm AWAY FROM END SUPPORT

VY = -87.45 MX = -0.97 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 92 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3535.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 883.8 mm 1767.5 mm 2651.2 mm 3535.0 mm
----------------------------------------------------------------------------
TOP 334.11 178.08 0.00 178.08 416.84
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 263.31 217.03 178.08 178.08 183.20

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 33 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 34

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 883.8 mm 1767.5 mm 2651.2 mm 3535.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 4-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 46.59 MX = 0.37 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -54.01 MX = 0.79 LD= 24
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 93 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3273.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 818.3 mm 1636.5 mm 2454.8 mm 3273.0 mm
----------------------------------------------------------------------------
TOP 339.22 178.08 178.08 313.41 746.64
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 215.77 178.08 178.08 196.34 202.70

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 34 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 35

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 818.3 mm 1636.5 mm 2454.8 mm 3273.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 7-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 2 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 49.00 MX = -0.99 LD= 21
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 640.1 mm AWAY FROM END SUPPORT

VY = -65.39 MX = -0.52 LD= 20
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 94 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2800.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 700.0 mm 1400.0 mm 2100.0 mm 2800.0 mm
----------------------------------------------------------------------------
TOP 216.67 0.00 0.00 178.08 190.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 35 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 36

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 700.0 mm 1400.0 mm 2100.0 mm 2800.0 mm
----------------------------------------------------------------------------
TOP 3-12í 2-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 33.41 MX = 0.03 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -35.04 MX = 0.59 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 95 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2273.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 568.2 mm 1136.5 mm 1704.7 mm 2273.0 mm
----------------------------------------------------------------------------
TOP 178.08 178.08 178.08 178.08 178.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 36 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 37

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 568.2 mm 1136.5 mm 1704.7 mm 2273.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 25.38 MX = 0.08 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -23.46 MX = 0.53 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 96 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3654.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 913.5 mm 1827.0 mm 2740.5 mm 3654.0 mm
----------------------------------------------------------------------------
TOP 248.67 178.08 0.00 178.08 235.43
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 37 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 38

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 913.5 mm 1827.0 mm 2740.5 mm 3654.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 42.68 MX = 0.77 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -38.19 MX = 0.85 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 97 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3322.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 830.5 mm 1661.0 mm 2491.5 mm 3322.0 mm
----------------------------------------------------------------------------
TOP 277.07 178.08 0.00 178.08 288.09
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 38 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 39

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 830.5 mm 1661.0 mm 2491.5 mm 3322.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 35.57 MX = 0.02 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -41.73 MX = 0.60 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 98 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 4325.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 1081.2 mm 2162.5 mm 3243.8 mm 4325.0 mm
----------------------------------------------------------------------------
TOP 290.82 178.08 0.00 178.08 356.53
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 178.08 0.00

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 39 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 40

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 1081.2 mm 2162.5 mm 3243.8 mm 4325.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 2-16í 3-16í 3-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 2-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 542.0 mm AWAY FROM START SUPPORT

VY = 40.59 MX = 0.84 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 542.0 mm AWAY FROM END SUPPORT

VY = -44.52 MX = 0.40 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 99 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 4759.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 1189.8 mm 2379.5 mm 3569.2 mm 4759.0 mm
----------------------------------------------------------------------------
TOP 421.19 178.08 0.00 178.08 369.26
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 210.00 195.48 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 40 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 41

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 1189.8 mm 2379.5 mm 3569.2 mm 4759.0 mm
----------------------------------------------------------------------------
TOP 4-12í 3-12í 2-12í 3-12í 4-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 55.30 MX = 0.01 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -49.81 MX = 0.57 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 100 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3322.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 830.5 mm 1661.0 mm 2491.5 mm 3322.0 mm
----------------------------------------------------------------------------
TOP 503.13 178.08 0.00 178.08 495.53
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 216.51 184.47 178.08 178.08 192.59

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 41 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 42

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 830.5 mm 1661.0 mm 2491.5 mm 3322.0 mm
----------------------------------------------------------------------------
TOP 5-12í 3-12í 2-12í 3-12í 5-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = 58.80 MX = 0.29 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 669.0 mm AWAY FROM END SUPPORT

VY = -59.93 MX = 0.14 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 101 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1775.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 443.8 mm 887.5 mm 1331.3 mm 1775.0 mm
----------------------------------------------------------------------------
TOP 189.26 178.08 178.08 190.24 373.91
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 247.35 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 42 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 43

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 443.8 mm 887.5 mm 1331.3 mm 1775.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 3-16í 3-16í 3-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = -44.01 MX = 4.11 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 642.0 mm AWAY FROM END SUPPORT

VY = -54.21 MX = 4.11 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 102 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2984.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 746.0 mm 1492.0 mm 2238.0 mm 2984.0 mm
----------------------------------------------------------------------------
TOP 547.21 179.46 0.00 178.08 334.05
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 202.36 278.34

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 43 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 44

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 746.0 mm 1492.0 mm 2238.0 mm 2984.0 mm
----------------------------------------------------------------------------
TOP 5-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM START SUPPORT

VY = 65.78 MX = 1.51 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM END SUPPORT

VY = -47.30 MX = 0.39 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 103 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2800.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 700.0 mm 1400.0 mm 2100.0 mm 2800.0 mm
----------------------------------------------------------------------------
TOP 355.92 178.08 0.00 178.08 247.79
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 44 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 45

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 700.0 mm 1400.0 mm 2100.0 mm 2800.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 2-16í 3-16í 3-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 642.0 mm AWAY FROM START SUPPORT

VY = 42.87 MX = 1.47 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 542.0 mm AWAY FROM END SUPPORT

VY = -41.42 MX = 1.04 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 104 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 2273.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 568.2 mm 1136.5 mm 1704.7 mm 2273.0 mm
----------------------------------------------------------------------------
TOP 193.94 178.08 0.00 178.08 178.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 45 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 46

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 568.2 mm 1136.5 mm 1704.7 mm 2273.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 34.52 MX = -1.33 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 105 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3277.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 819.2 mm 1638.5 mm 2457.8 mm 3277.0 mm
----------------------------------------------------------------------------
TOP 309.15 178.08 0.00 178.08 263.82
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 819.2 mm 1638.5 mm 2457.8 mm 3277.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 2-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 46 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 47

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 45.70 MX = 0.78 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM END SUPPORT

VY = -36.91 MX = 0.91 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 106 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1775.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 443.8 mm 887.5 mm 1331.3 mm 1775.0 mm
----------------------------------------------------------------------------
TOP 178.08 178.08 178.08 178.08 178.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 0.00 0.00

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 443.8 mm 887.5 mm 1331.3 mm 1775.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 3-12í 3-12í 3-12í 2-12í 2-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 444.0 mm AWAY FROM START SUPPORT

VY = -14.24 MX = 0.91 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 444.0 mm AWAY FROM END SUPPORT

VY = -21.63 MX = 0.91 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 47 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 48

============================================================================
B E A M N O. 107 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1775.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 443.8 mm 887.5 mm 1331.3 mm 1775.0 mm
----------------------------------------------------------------------------
TOP 178.08 178.08 178.08 178.08 178.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 178.08 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 443.8 mm 887.5 mm 1331.3 mm 1775.0 mm
----------------------------------------------------------------------------
TOP 3-12í 3-12í 3-12í 3-12í 3-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 16.58 MX = 1.91 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 108 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 5040.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 48 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 49

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 1260.0 mm 2520.0 mm 3780.0 mm 5040.0 mm
----------------------------------------------------------------------------
TOP 350.88 178.08 0.00 178.08 382.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 178.08 0.00

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 1260.0 mm 2520.0 mm 3780.0 mm 5040.0 mm
----------------------------------------------------------------------------
TOP 3-16í 3-16í 2-16í 3-16í 3-16í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 2-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 542.0 mm AWAY FROM START SUPPORT

VY = 47.21 MX = -0.86 LD= 11
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 542.0 mm AWAY FROM END SUPPORT

VY = -49.82 MX = -0.86 LD= 11
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 109 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 4533.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 1133.3 mm 2266.5 mm 3399.8 mm 4533.0 mm
----------------------------------------------------------------------------
TOP 399.94 178.08 0.00 178.08 492.03
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 0.00 178.08 178.08 188.65 178.08

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 49 of 612

 Thursday, March 27, 2025, 09:26 PM
STAAD SPACE -- PAGE NO. 50

SUMMARY OF PROVIDED REINF. AREA

----------------------------------------------------------------------------
SECTION 0.0 mm 1133.3 mm 2266.5 mm 3399.8 mm 4533.0 mm
----------------------------------------------------------------------------
TOP 4-12í 3-12í 2-12í 3-12í 5-12í
REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

BOTTOM 2-12í 3-12í 3-12í 3-12í 3-12í

REINF. 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s) 1 layer(s)

SHEAR 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í 2 legged 8í

REINF. @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c @ 150 mm c/c
----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------

SHEAR DESIGN RESULTS AT 544.0 mm AWAY FROM START SUPPORT

VY = 52.98 MX = 0.08 LD= 23
Provide 2 Legged 8í @ 150 mm c/c

SHEAR DESIGN RESULTS AT 644.0 mm AWAY FROM END SUPPORT

VY = -49.75 MX = 0.13 LD= 22
Provide 2 Legged 8í @ 150 mm c/c

============================================================================

============================================================================
B E A M N O. 110 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3500.0 mm SIZE: 250.0 mm X 450.0 mm COVER: 25.0 mm

SUMMARY OF REINF. AREA (Sq.mm)

----------------------------------------------------------------------------
SECTION 0.0 mm 875.0 mm 1750.0 mm 2625.0 mm 3500.0 mm
----------------------------------------------------------------------------
TOP 658.13 216.02 0.00 0.00 178.08
REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)

BOTTOM 178.08 178.08 178.08 202.39 216.63

REINF. (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm) (Sq. mm)
----------------------------------------------------------------------------

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 50 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 469

============================================================================

C O L U M N N O. 1 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 23 END JOINT: 36 SHORT COLUMN

REQD. STEEL AREA : 362.72 Sq.mm.

REQD. CONCRETE AREA: 112137.28 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1145.25 Muz1 : 72.25 Muy1 : 37.48

INTERACTION RATIO: 0.35 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 22
END JOINT: 36 Puz : 1343.65 Muz : 96.52 Muy : 46.41 IR: 0.35
============================================================================

============================================================================

C O L U M N N O. 2 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 23 END JOINT: 37 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 469 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 470

REQD. STEEL AREA : 685.25 Sq.mm.

REQD. CONCRETE AREA: 111814.75 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1263.30 Muz1 : 36.33 Muy1 : 71.22

INTERACTION RATIO: 0.44 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 23
END JOINT: 37 Puz : 1343.65 Muz : 40.94 Muy : 82.89 IR: 0.37
============================================================================

============================================================================

C O L U M N N O. 3 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 38 SHORT COLUMN

REQD. STEEL AREA : 602.37 Sq.mm.

REQD. CONCRETE AREA: 111897.63 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1232.97 Muz1 : 74.39 Muy1 : 37.93

INTERACTION RATIO: 0.26 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 24
END JOINT: 38 Puz : 1343.65 Muz : 94.40 Muy : 45.77 IR: 0.29

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 470 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 471

============================================================================

============================================================================

C O L U M N N O. 4 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 39 SHORT COLUMN

REQD. STEEL AREA : 601.08 Sq.mm.

REQD. CONCRETE AREA: 111898.92 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1232.49 Muz1 : 74.43 Muy1 : 37.95

INTERACTION RATIO: 0.26 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 23
END JOINT: 39 Puz : 1343.65 Muz : 99.04 Muy : 47.54 IR: 0.30
============================================================================

============================================================================

C O L U M N N O. 5 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 500.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 5 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 471 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 472

REQD. STEEL AREA : 1400.00 Sq.mm.

REQD. CONCRETE AREA: 123600.00 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 16 dia. (1.29%, 1608.50 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 250 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1637.40 Muz1 : 29.38 Muy1 : 67.02

INTERACTION RATIO: 0.93 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 40 Puz : 1713.71 Muz : 34.73 Muy : 81.80 IR: 0.68
============================================================================

============================================================================

C O L U M N N O. 6 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 6 SHORT COLUMN

REQD. STEEL AREA : 900.00 Sq.mm.

REQD. CONCRETE AREA: 111600.00 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1341.90 Muz1 : 49.47 Muy1 : 24.82

INTERACTION RATIO: 0.91 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 41 Puz : 1343.65 Muz : 49.42 Muy : 24.82 IR: 0.92

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 472 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 473

============================================================================

============================================================================

C O L U M N N O. 7 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 20 END JOINT: 42 SHORT COLUMN

REQD. STEEL AREA : 674.62 Sq.mm.

REQD. CONCRETE AREA: 111825.38 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1259.41 Muz1 : 71.72 Muy1 : 36.59

INTERACTION RATIO: 0.30 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 20
END JOINT: 42 Puz : 1343.65 Muz : 83.88 Muy : 41.38 IR: 0.26
============================================================================

============================================================================

C O L U M N N O. 8 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 43 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 473 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 474

REQD. STEEL AREA : 808.76 Sq.mm.

REQD. CONCRETE AREA: 111691.24 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1308.51 Muz1 : 63.76 Muy1 : 32.39

INTERACTION RATIO: 0.45 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 43 Puz : 1343.65 Muz : 69.59 Muy : 34.78 IR: 0.40
============================================================================

============================================================================

C O L U M N N O. 9 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 21 END JOINT: 44 SHORT COLUMN

REQD. STEEL AREA : 702.53 Sq.mm.

REQD. CONCRETE AREA: 111797.47 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1269.63 Muz1 : 70.36 Muy1 : 35.88

INTERACTION RATIO: 0.32 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 22
END JOINT: 9 Puz : 1343.65 Muz : 99.54 Muy : 48.05 IR: 0.32

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 474 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 475

============================================================================

============================================================================

C O L U M N N O. 11 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 18 END JOINT: 11 TENSION COLUMN

REQD. STEEL AREA : 900.00 Sq.mm.

REQD. CONCRETE AREA: 111600.00 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1341.90 Muz1 : 51.10 Muy1 : 25.57

INTERACTION RATIO: 0.33 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 22
END JOINT: 46 Puz : 1343.65 Muz : 37.51 Muy : 19.18 IR: 0.65
============================================================================

============================================================================

C O L U M N N O. 12 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 21 END JOINT: 47 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 475 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 476

REQD. STEEL AREA : 641.19 Sq.mm.

REQD. CONCRETE AREA: 111858.80 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1247.18 Muz1 : 37.30 Muy1 : 73.12

INTERACTION RATIO: 0.28 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 23
END JOINT: 47 Puz : 1343.65 Muz : 48.74 Muy : 100.69 IR: 0.38
============================================================================

============================================================================

C O L U M N N O. 15 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 20 END JOINT: 50 SHORT COLUMN

REQD. STEEL AREA : 615.82 Sq.mm.

REQD. CONCRETE AREA: 111884.18 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1237.89 Muz1 : 73.99 Muy1 : 37.73

INTERACTION RATIO: 0.31 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 23
END JOINT: 50 Puz : 1343.65 Muz : 92.14 Muy : 43.64 IR: 0.27

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 476 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 477

============================================================================

============================================================================

C O L U M N N O. 16 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 51 SHORT COLUMN

REQD. STEEL AREA : 643.73 Sq.mm.

REQD. CONCRETE AREA: 111856.27 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1248.10 Muz1 : 73.02 Muy1 : 37.25

INTERACTION RATIO: 0.28 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 25
END JOINT: 51 Puz : 1343.65 Muz : 90.86 Muy : 44.35 IR: 0.36
============================================================================

============================================================================

C O L U M N N O. 17 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 52 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 477 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 478

REQD. STEEL AREA : 888.73 Sq.mm.

REQD. CONCRETE AREA: 111611.27 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1337.77 Muz1 : 28.92 Muy1 : 57.13

INTERACTION RATIO: 0.62 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 52 Puz : 1343.65 Muz : 29.48 Muy : 58.86 IR: 0.60
============================================================================

============================================================================

C O L U M N N O. 18 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 53 SHORT COLUMN

REQD. STEEL AREA : 727.42 Sq.mm.

REQD. CONCRETE AREA: 111772.59 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1278.73 Muz1 : 69.01 Muy1 : 35.18

INTERACTION RATIO: 0.35 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 25
END JOINT: 53 Puz : 1343.65 Muz : 93.58 Muy : 45.45 IR: 0.32

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 478 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 479

============================================================================

============================================================================

C O L U M N N O. 19 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 19 SHORT COLUMN

REQD. STEEL AREA : 1260.00 Sq.mm.

REQD. CONCRETE AREA: 111240.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.21%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1473.66 Muz1 : 55.03 Muy1 : 27.26

INTERACTION RATIO: 0.91 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 54 Puz : 1509.22 Muz : 61.02 Muy : 29.57 IR: 0.78
============================================================================

============================================================================

C O L U M N N O. 20 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 55 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 479 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 480

REQD. STEEL AREA : 832.77 Sq.mm.

REQD. CONCRETE AREA: 111667.23 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1317.30 Muz1 : 61.89 Muy1 : 31.46

INTERACTION RATIO: 0.49 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 20
END JOINT: 55 Puz : 1343.65 Muz : 75.18 Muy : 37.43 IR: 0.46
============================================================================

============================================================================

C O L U M N N O. 21 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 56 SHORT COLUMN

REQD. STEEL AREA : 696.91 Sq.mm.

REQD. CONCRETE AREA: 111803.09 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1267.57 Muz1 : 70.65 Muy1 : 36.03

INTERACTION RATIO: 0.32 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 21
END JOINT: 56 Puz : 1343.65 Muz : 81.82 Muy : 40.47 IR: 0.44

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 480 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 481

============================================================================

============================================================================

C O L U M N N O. 22 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 57 SHORT COLUMN

REQD. STEEL AREA : 1080.00 Sq.mm.

REQD. CONCRETE AREA: 111420.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.21%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1407.78 Muz1 : 54.03 Muy1 : 26.78

INTERACTION RATIO: 0.84 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 57 Puz : 1509.22 Muz : 70.26 Muy : 34.09 IR: 0.55
============================================================================

============================================================================

C O L U M N N O. 23 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 23 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 481 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 482

REQD. STEEL AREA : 1080.00 Sq.mm.

REQD. CONCRETE AREA: 111420.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.21%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1407.78 Muz1 : 51.85 Muy1 : 25.97

INTERACTION RATIO: 0.92 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 58 Puz : 1509.22 Muz : 67.78 Muy : 32.93 IR: 0.60
============================================================================

============================================================================

C O L U M N N O. 24 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 59 SHORT COLUMN

REQD. STEEL AREA : 846.23 Sq.mm.

REQD. CONCRETE AREA: 111653.77 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1322.22 Muz1 : 60.80 Muy1 : 30.88

INTERACTION RATIO: 0.51 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 21
END JOINT: 59 Puz : 1343.65 Muz : 70.41 Muy : 35.17 IR: 0.56

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 482 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 483

============================================================================

============================================================================

C O L U M N N O. 25 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 600.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 25 SHORT COLUMN

REQD. STEEL AREA : 2040.00 Sq.mm.

REQD. CONCRETE AREA: 147960.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 16 dia. (1.61%, 2412.74 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 250 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 2096.64 Muz1 : 107.90 Muy1 : 37.72

INTERACTION RATIO: 0.90 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 60 Puz : 2233.06 Muz : 139.56 Muy : 47.08 IR: 0.60
============================================================================

============================================================================

C O L U M N N O. 26 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 500.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 26 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 483 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 484

REQD. STEEL AREA : 1600.00 Sq.mm.

REQD. CONCRETE AREA: 123400.00 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 16 dia. (1.29%, 1608.50 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 250 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1710.60 Muz1 : 73.89 Muy1 : 32.13

INTERACTION RATIO: 0.83 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 61 Puz : 1713.71 Muz : 74.41 Muy : 31.79 IR: 0.85
============================================================================

============================================================================

C O L U M N N O. 27 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 62 SHORT COLUMN

REQD. STEEL AREA : 887.15 Sq.mm.

REQD. CONCRETE AREA: 111612.85 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1337.20 Muz1 : 57.28 Muy1 : 29.00

INTERACTION RATIO: 0.62 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 21
END JOINT: 62 Puz : 1343.65 Muz : 65.19 Muy : 32.64 IR: 0.84

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 484 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 485

============================================================================

============================================================================

C O L U M N N O. 28 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 500.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 20 END JOINT: 63 SHORT COLUMN

REQD. STEEL AREA : 1100.00 Sq.mm.

REQD. CONCRETE AREA: 123900.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.09%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1527.60 Muz1 : 74.17 Muy1 : 33.12

INTERACTION RATIO: 0.95 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 20
END JOINT: 63 Puz : 1621.72 Muz : 90.94 Muy : 39.35 IR: 0.70
============================================================================

============================================================================

C O L U M N N O. 29 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 64 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 485 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 486

REQD. STEEL AREA : 775.51 Sq.mm.

REQD. CONCRETE AREA: 111724.49 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1296.34 Muz1 : 66.01 Muy1 : 33.62

INTERACTION RATIO: 0.40 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 21
END JOINT: 64 Puz : 1343.65 Muz : 76.66 Muy : 38.13 IR: 0.60
============================================================================

============================================================================

C O L U M N N O. 30 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 500.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 30 SHORT COLUMN

REQD. STEEL AREA : 1500.00 Sq.mm.

REQD. CONCRETE AREA: 123500.00 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 16 dia. (1.29%, 1608.50 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 250 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1674.00 Muz1 : 31.31 Muy1 : 71.63

INTERACTION RATIO: 0.84 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 65 Puz : 1713.71 Muz : 33.69 Muy : 79.55 IR: 0.74

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 486 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 487

============================================================================

============================================================================

C O L U M N N O. 31 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 END JOINT: 31 SHORT COLUMN

REQD. STEEL AREA : 1170.00 Sq.mm.

REQD. CONCRETE AREA: 111330.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.21%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1440.72 Muz1 : 27.57 Muy1 : 55.92

INTERACTION RATIO: 0.83 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
END JOINT: 66 Puz : 1509.22 Muz : 32.24 Muy : 66.33 IR: 0.63
============================================================================

============================================================================

C O L U M N N O. 32 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 20 END JOINT: 67 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 487 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 488

REQD. STEEL AREA : 599.17 Sq.mm.

REQD. CONCRETE AREA: 111900.83 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1231.80 Muz1 : 74.48 Muy1 : 37.98

INTERACTION RATIO: 0.59 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 24
END JOINT: 67 Puz : 1343.65 Muz : 92.21 Muy : 44.90 IR: 0.51
============================================================================

============================================================================

C O L U M N N O. 33 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 22 END JOINT: 68 SHORT COLUMN

REQD. STEEL AREA : 569.53 Sq.mm.

REQD. CONCRETE AREA: 111930.48 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1220.95 Muz1 : 38.34 Muy1 : 75.20

INTERACTION RATIO: 0.41 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 24
END JOINT: 68 Puz : 1343.65 Muz : 48.67 Muy : 102.19 IR: 0.45

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 488 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 489

============================================================================

============================================================================

C O L U M N N O. 34 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 21 END JOINT: 69 SHORT COLUMN

REQD. STEEL AREA : 468.37 Sq.mm.

REQD. CONCRETE AREA: 112031.63 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1183.92 Muz1 : 38.73 Muy1 : 75.90

INTERACTION RATIO: 0.35 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 22
END JOINT: 69 Puz : 1343.65 Muz : 48.36 Muy : 101.41 IR: 0.40
============================================================================

============================================================================

C O L U M N N O. 35 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 1500.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 22 END JOINT: 70 SHORT COLUMN

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 489 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 490

REQD. STEEL AREA : 599.37 Sq.mm.

REQD. CONCRETE AREA: 111900.62 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1231.87 Muz1 : 37.98 Muy1 : 74.48

INTERACTION RATIO: 0.47 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 24
END JOINT: 70 Puz : 1343.65 Muz : 45.62 Muy : 94.00 IR: 0.47
============================================================================

============================================================================

C O L U M N N O. 36 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 23 SHORT(Z) /BRACED LONG(Y)

REQD. STEEL AREA : 330.83 Sq.mm.

REQD. CONCRETE AREA: 112169.16 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1133.58 Muz1 : 69.67 Muy1 : 36.32

INTERACTION RATIO: 0.65 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 21
Puz : 1343.65 Muz : 102.38 Muy : 49.61 IR: 0.53

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 490 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 491

============================================================================

============================================================================

C O L U M N N O. 37 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 23 BRACED LONG(Z) /SHORT(Y)

REQD. STEEL AREA : 638.55 Sq.mm.

REQD. CONCRETE AREA: 111861.45 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1246.21 Muz1 : 37.35 Muy1 : 73.22

INTERACTION RATIO: 0.99 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 23
Puz : 1343.65 Muz : 42.75 Muy : 87.07 IR: 0.91
============================================================================

============================================================================

C O L U M N N O. 38 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 SHORT(Z) /BRACED LONG(Y)

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 491 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 492

REQD. STEEL AREA : 580.01 Sq.mm.

REQD. CONCRETE AREA: 111919.99 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1224.78 Muz1 : 74.97 Muy1 : 38.22

INTERACTION RATIO: 0.56 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 24
Puz : 1343.65 Muz : 96.28 Muy : 46.51 IR: 0.63
============================================================================

============================================================================

C O L U M N N O. 39 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 SHORT(Z) /BRACED LONG(Y)

REQD. STEEL AREA : 572.98 Sq.mm.

REQD. CONCRETE AREA: 111927.02 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1222.21 Muz1 : 75.13 Muy1 : 38.30

INTERACTION RATIO: 0.56 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 21
Puz : 1343.65 Muz : 95.33 Muy : 46.14 IR: 0.62

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 492 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 493

============================================================================

============================================================================

C O L U M N N O. 40 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 500.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 BRACED LONG(Z) /SHORT(Y)

REQD. STEEL AREA : 1800.00 Sq.mm.

REQD. CONCRETE AREA: 123200.00 Sq.mm.
MAIN REINFORCEMENT : Provide 16 - 12 dia. (1.45%, 1809.56 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1783.80 Muz1 : 41.58 Muy1 : 97.20

INTERACTION RATIO: 0.92 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
Puz : 1787.30 Muz : 41.79 Muy : 98.07 IR: 0.96
============================================================================

============================================================================

C O L U M N N O. 41 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 SHORT(Z) /BRACED LONG(Y)

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 493 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 494

REQD. STEEL AREA : 1170.00 Sq.mm.

REQD. CONCRETE AREA: 111330.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.21%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1440.72 Muz1 : 67.21 Muy1 : 33.37

INTERACTION RATIO: 0.97 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
Puz : 1509.22 Muz : 77.72 Muy : 37.68 IR: 0.88
============================================================================

============================================================================

C O L U M N N O. 42 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 20 SHORT(Z) /BRACED LONG(Y)

REQD. STEEL AREA : 643.24 Sq.mm.

REQD. CONCRETE AREA: 111856.76 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1247.93 Muz1 : 73.04 Muy1 : 37.26

INTERACTION RATIO: 0.61 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 20
Puz : 1343.65 Muz : 86.67 Muy : 42.58 IR: 0.58

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 494 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 495

============================================================================

============================================================================

C O L U M N N O. 43 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 SHORT(Z) /BRACED LONG(Y)

REQD. STEEL AREA : 779.91 Sq.mm.

REQD. CONCRETE AREA: 111720.09 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1297.95 Muz1 : 65.72 Muy1 : 33.46

INTERACTION RATIO: 0.81 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
Puz : 1343.65 Muz : 73.03 Muy : 36.42 IR: 0.78
============================================================================

============================================================================

C O L U M N N O. 44 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 21 SHORT(Z) /BRACED LONG(Y)

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 495 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 496

REQD. STEEL AREA : 676.53 Sq.mm.

REQD. CONCRETE AREA: 111823.47 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1260.11 Muz1 : 71.63 Muy1 : 36.55

INTERACTION RATIO: 0.65 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 24
Puz : 1343.65 Muz : 100.30 Muy : 48.48 IR: 0.69
============================================================================

============================================================================

C O L U M N N O. 46 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 18 END JOINT: 11 TENSION COLUMN

REQD. STEEL AREA : 900.00 Sq.mm.

REQD. CONCRETE AREA: 111600.00 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1341.90 Muz1 : 66.98 Muy1 : 33.00

INTERACTION RATIO: 0.28 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 23
END JOINT: 11 Puz : 1343.65 Muz : 96.54 Muy : 46.61 IR: 0.48

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 496 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 497

============================================================================

============================================================================

C O L U M N N O. 47 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 21 BRACED LONG(Z) /SHORT(Y)

REQD. STEEL AREA : 622.44 Sq.mm.

REQD. CONCRETE AREA: 111877.56 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1240.31 Muz1 : 37.63 Muy1 : 73.78

INTERACTION RATIO: 0.59 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 22
Puz : 1343.65 Muz : 47.01 Muy : 97.60 IR: 0.81
============================================================================

============================================================================

C O L U M N N O. 50 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 20 SHORT(Z) /BRACED LONG(Y)

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 497 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 498

REQD. STEEL AREA : 569.99 Sq.mm.

REQD. CONCRETE AREA: 111930.01 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1221.12 Muz1 : 75.19 Muy1 : 38.34

INTERACTION RATIO: 0.55 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 23
Puz : 1343.65 Muz : 92.70 Muy : 44.02 IR: 0.59
============================================================================

============================================================================

C O L U M N N O. 51 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 SHORT(Z) /BRACED LONG(Y)

REQD. STEEL AREA : 615.29 Sq.mm.

REQD. CONCRETE AREA: 111884.70 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1237.70 Muz1 : 74.01 Muy1 : 37.74

INTERACTION RATIO: 0.66 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 25
Puz : 1343.65 Muz : 93.78 Muy : 45.53 IR: 0.74

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 498 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 499

============================================================================

============================================================================

C O L U M N N O. 52 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 450.0 mm X 250.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 22 BRACED LONG(Z) /SHORT(Y)

REQD. STEEL AREA : 1090.07 Sq.mm.

REQD. CONCRETE AREA: 111409.93 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.21%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1411.47 Muz1 : 40.10 Muy1 : 81.08

INTERACTION RATIO: 1.00 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 22
Puz : 1509.22 Muz : 45.23 Muy : 94.25 IR: 0.93
============================================================================

============================================================================

C O L U M N N O. 53 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 SHORT(Z) /BRACED LONG(Y)

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 499 of 612

 Thursday, March 27, 2025, 09:27 PM
STAAD SPACE -- PAGE NO. 500

REQD. STEEL AREA : 706.36 Sq.mm.

REQD. CONCRETE AREA: 111793.64 Sq.mm.
MAIN REINFORCEMENT : Provide 8 - 12 dia. (0.80%, 904.78 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1271.03 Muz1 : 70.16 Muy1 : 35.78

INTERACTION RATIO: 0.69 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 20
Puz : 1343.65 Muz : 87.95 Muy : 43.13 IR: 0.70
============================================================================

============================================================================

C O L U M N N O. 54 D E S I G N R E S U L T S

M20 Fe500 (Main) Fe500 (Sec.)

LENGTH: 3400.0 mm CROSS SECTION: 250.0 mm X 450.0 mm COVER: 40.0 mm

** GUIDING LOAD CASE: 11 SHORT(Z) /BRACED LONG(Y)

REQD. STEEL AREA : 1350.00 Sq.mm.

REQD. CONCRETE AREA: 111150.00 Sq.mm.
MAIN REINFORCEMENT : Provide 12 - 12 dia. (1.21%, 1357.17 Sq.mm.)
(Equally distributed)
TIE REINFORCEMENT : Provide 8 mm dia. rectangular ties @ 190 mm c/c

SECTION CAPACITY BASED ON REINFORCEMENT REQUIRED (KNS-MET)

----------------------------------------------------------
Puz : 1506.60 Muz1 : 72.41 Muy1 : 35.55

INTERACTION RATIO: 0.93 (as per Cl. 39.6, IS456:2000)

SECTION CAPACITY BASED ON REINFORCEMENT PROVIDED (KNS-MET)

----------------------------------------------------------
WORST LOAD CASE: 11
Puz : 1509.22 Muz : 73.58 Muy : 35.64 IR: 0.98

D:\JDC DATA\Desktop\Vastukaar\Thakdari Project\TAKDARI - 2.anl Page 500 of 612