Scribd
Upload
5 views5 pages

LUT_3D_4SystemAnalysis

This document provides instructions on how to install and use the LUT_3D_4SystemAnalysis macro in Flux software. The macro creates a lookup table for flux dq, Ld, Lq, and torque based on Id, Iq, and rotor position, generating an output OML file. It outlines prerequisites for the circuit setup and detailed steps for installation and execution of the macro.

Uploaded by

Cầu Cao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
5 views5 pages

LUT_3D_4SystemAnalysis

This document provides instructions on how to install and use the LUT_3D_4SystemAnalysis macro in Flux software. The macro creates a lookup table for flux dq, Ld, Lq, and torque based on Id, Iq, and rotor position, generating an output OML file. It outlines prerequisites for the circuit setup and detailed steps for installation and execution of the macro.

Uploaded by

Cầu Cao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

FLUX Macros

How to use macro : LUT_3D_4SystemAnalysis ?

Creation 21/11/2022
Last update Jul 11th 2023 (NA)
Version soft Flux 2022.3
Author NA
Reviewers PL

Introduction This document deals with how to install a macro, and how to use the
LUT_3D_4SystemAnalysis. It will include the following topics:
• Macro definition: LUT_3D_4SystemAnalysis
• Install a macro

1
FLUX Macros

Macro definition : LUT_3D_4SystemAnalaysis

Goal of the This macro intends to create look up table of flux dq, Ld, Lq and torque
macro versus Id, Iq and rotor position (if needed). The goal is for analysis on the
system part (like with Activate or PSIM for instance). It will create a new
Magneto-Static project from the transient magnetic one. In the Magneto-
Static project the current is driven with Id and Iq allowing to extract easily all
the needed tables. At the end of the oml file in comment there is the
possibility to display Ld, Lq and torque versus Id and Iq with Altair
Compose. An *.mat file is created.

Figure 1 : interface of LUT_3D_4SystemAnalysist

The output will be an oml file called name_of_project_MS_table_res.oml.

Figure 2: example of output file


Note that there are some pre-requisites to fulfil:
• The circuit must have only 3 coil conductors
• No compressible mechanical set
• Delete all results

2
FLUX Macros

Install a macro

Installing a Once you have taken a new macro (from a colleague or from Altair web site
macro (https://community.altair.com/community), you have to unzip it in the
following directory (for standard installation):
• C:\Program Files\Altair\2022.1\flux\Extensions\Macros

Note Macro has to be directly in folder:


C:\Program Files\Altair\2022.1\flux\Extensions\Macros

Calling a macro In order to use a macro, you have to follow the next steps:

Step Actions
1 Open Flux
2 Click on [Project] [Macro] [Load], and select the right macro

3 To run a macro, you have to click on [Project] [Macro] [Run]

Then select the macro you want to run.

3
FLUX Macros

Description

Folder Macros Description


Macros_ LUT_3D_ Create look up table from TM project of Flux dq,
4SystemAnalysis 4SystemAnalysis.PFM Ld, Lq and torque versus Id, Iq and rotor position.

Input:
• Current in 3 supplies
• Select mobile mechanical set
• Select fixed mechanical set
• Max value for Id
• Number of values for Id (odd)
• Number of poles
• Number of pole pairs represented in geometry
(0.5 for one pole)
• Number of stator periodicities
• Depending on rotor position
• Fast computation or not
• Number of steps in the electric period
• Period for rotation (in degrees)
• Motor Viscous Damping and Moment of
Inertia (For System computation in
Activate/PSIM, can be set to 0 if unused.)
Output:
• Create a result OML file with name created
from the initial file (*_res.oml)
• It will also include more data such as phase
resistance, end winding inductance, electric
period and initial rotor position plus
possibility to display values in Compose

4
FLUX Macros

Répertoire Macros Description


Macros_ LUT_3D_ Créer des tables depuis un projet transitoire de
4SystemAnalysis 4SystemAnalysis.PFM moteur à aimant pour définir le flux dq, Ld, Lq et
couple en fonction de Id, Iq et de la position du
rotor

Entrée:
• Courant dans les 3 sources
• Sélectionner l’ensemble mécanique mobile
• Sélectionner l’ensemble mécanique fixe
• Valeur max pour Id
• Nombre de valeurs pour Id (impair)
• Nombre de pôles
• Nombre de paires de pôles représenté dans la
géométrie
• Nombre de périodicités au stator
• Dépendant de la position du rotor
• Calcul rapide
• Nombre de pas dans la période électrique
• Période électrique (en degrés)
• Coefficient de viscosité du moteur (en
Nms/degré) et Moment d’Inertie du moteur
(en kg/m²) (Pour analyse systémique dans
Activate/PSIM, peut être mis à 0 si non
utilisé)
Output:
• Créer un fichier OML à partir du nom initial
(*_res.oml)
• Ces résultats incluent aussi la résistance de
phase, l’inductance de tête de bobine, période
électrique et position initiale du rotor plus le
script pour afficher les tables dans Compose

You might also like