MOHAVE/BORREGO(HM) > 2010 > G 4.
6 DOHC > Airbag > Airbag Control > B1361
Pretensioner Front-Driver Resistance too High
B1361 Pretensioner Front-Driver Resistance too High > General Information
Component Location
General Description
Seat Belt Pretensioner(hereinafter referred to BPT) is located at both side of center pillar.
BPT tightens seat belt before air bag deploys to protect passenger from bumping against crush pad, steering wheel and front
window.
In BPT, there are a ignition circuit and cylinder for rewinding belt.
Cylinder has piston that can rewind seat belt in it.
Gas chamber generates expansive force of gases to push piston in cylinder.
Never measure resistance of BPT directly, Current of measuring device may cause unexpected BPT depoy.
DTC Description
The SRSCM sets DTC B1361 if the measured resistance value of DBPT circuit is more than the threshold value.
*In this case, SRSCM checks if there's any fault in circuit by sending current for a while.
DTC Detecting Condition
Item Detecting Condition Possible cause
DTC Strategy • Check Resistance
• Poor connection of connected
Enable Conditions • Ignition "ON" part.
Threshold Value • DBPT resistance ≥ 6.4Ω • Poor connection between shorting
bar and release pin.
Qualification • More than 2.5s (250ms x 10)
Diagnostic • Faulty DBPT.
Time De- • Faulty SRSCM.
• More than 5s
Qualification
Specification
Test Condition Resistance
Ignition ON 1.4Ω ≤ Squib resistance ≤ 6.4Ω
Diagnostic Circuit Diagram
B1361 Pretensioner Front-Driver Resistance too High > Scantool Diagnostics
Monitor Scantool Data
1. Ignition "OFF", connect scantool.
2. Ignition "ON"& Engine "OFF", select "Diagnostic Trouble Codes(DTC)" mode.
3. Monitor diagnostic trouble code and present of trouble code.
4. Using a scan tool, clear the DTC.
5. Is DTC present problem ?
▶ Go to "W/Harness Inspection" procedure.
▶ Displaying nothing(no DTC) or DTC with label "H"(historical) shows that Fault is intermittent caused by
poor contact in the part's and/or SRSCM connector or was repaired and SRSCM memory was not cleared.
Thoroughly check shorting bar/shorting bar release pin and connectors for looseness, poor connection,
bending, corrosion, contamination, deterioration, or damage.
▶ Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.
B1361 Pretensioner Front-Driver Resistance too High > Inspection/Repair > W/Harness Inspection
Terminal and Connector Inspection
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check shorting bar/shorting bar release pin and connectors for looseness, poor connection, bending, corrosion,
contamination, deterioration, or damage.
3. Has a problem been found?
▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
▶ Go to "Squib Circuit Inspection" procedure.
Squib Circuit Inspection
1. Ignition "OFF".
2. Disconnect (-) terminal cable from battery and wait for 1 minutes or more.
3. Disconnect DBPT module and connect the dummy (0957A-38200) and dummy adapter (0957A-1C000) to main harness
connector.
If dummy and dummy adaptor are not able to be prepared, use a known-good DBPT or 2Ω resistor.
4. Connect (-) terminal cable to battery and Ignition "ON" & Engine "OFF" and wait for 30 seconds or more.
5. Connect scantool to Data Link Connector(DLC) and clear DTC with scantool and diagnose again.
6. Is DTC present problem ?
▶ Go to "Main harness circuit inspection" procedure.
▶ Substitute a known-good DBPT assembly, and check for proper operation.
If the problem is corrected, replace DBPT and then go to "Verification of Vehicle Repair" procedure.
Main harness Circuit Inspection
1. Ignition "OFF".
2. Disconnect the battery (-) terminal cable from the battery and wait at least one minutes.
3. Disconnect DBPT connector and SRSCM main harness connector.
4. Measure resistance between terminal "Low" and "High" of the DBPT harness connector.
Specification : approx. 1 Ω below
5. Is the measured resistance within specifications?
▶ Substitute a known-good SRSCM, and check for proper operation.
If the problem is corrected, replace SRSCM and then go to "Verification of Vehicle Repair" procedure.
If you strike or spin the SRSCM at the IG “ON” state, the seat-belt pretensioner, curtain-airbag or side-
airbag could be unfolded and bring on danger. Handle it with care.
▶ Substitute the SRSCM main harness and check for proper operation.
If the problem is corrected, replace SRSCM main harness and then go to "Verification of Vehicle Repair"
procedure.
B1361 Pretensioner Front-Driver Resistance too High > Verification of Vehicle Repair
Verification of Vehicle Repair
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scan tool and select "Diagnostic Trouble Codes(DTC)" mode
2. Using a scan tool, clear the DTC.
3. Operate the vehicle within DTC Enable conditions in General information.
4. Are any DTC present ?
▶ Go to the applicable troubleshooting procedure.
▶ System is performing to specification at this time.
B1361 Pretensioner Front-Driver Resistance too High > 회로도 입력
Schematic Circuit Diagram
