CY21 ROKFC IN-KIND A20R210P2, UNACCOMPANIED ENLISTED
PERSONNEL HOUSING (UEPH 100B), USAG HUMPHREYS, KOREA
SECTION TABLE OF CONTENTS
DIVISION 08 - OPENINGS
SECTION 08 91 00
METAL WALL LOUVERS
PART 1 GENERAL
1.1 REFERENCES
1.2 SUBMITTALS
1.3 DELIVERY, STORAGE, AND PROTECTION
1.4 DETAIL DRAWINGS
1.5 COLOR SAMPLES
PART 2 PRODUCTS
2.1 MATERIALS
2.1.1 Aluminum Sheet
2.1.2 Extruded Aluminum
2.2 METAL WALL LOUVERS
2.2.1 Extruded Aluminum Louvers
2.2.2 Screens and Frames
2.3 FASTENERS AND ACCESSORIES
2.4 FINISHES
2.4.1 Aluminum
2.4.1.1 Anodic Coating
PART 3 EXECUTION
3.1 INSTALLATION
3.1.1 Wall Louvers
3.1.2 Screens and Frames
3.2 PROTECTION FROM CONTACT OF DISSIMILAR MATERIALS
3.2.1 Aluminum
-- End of Section Table of Contents --
SECTION 08 91 00 Page 1
CY21 ROKFC IN-KIND A20R210P2, UNACCOMPANIED ENLISTED
PERSONNEL HOUSING (UEPH 100B), USAG HUMPHREYS, KOREA
SECTION 08 91 00
METAL WALL LOUVERS
PART 1 GENERAL
1.1 REFERENCES
The publications listed below form a part of this specification to the
extent referenced. The publications are referred to within the text by the
basic designation only.
AIR MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. (AMCA)
AMCA 500-L (2015) Laboratory Methods of Testing
Louvers for Rating
AMCA 511 (2010; R 2016) Certified Ratings Program
for Air Control Devices
ALUMINUM ASSOCIATION (AA)
AA DAF45 (2003; Reaffirmed 2009) Designation System
for Aluminum Finishes
AMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA)
AAMA 611 (2014) Voluntary Specification for
Anodized Architectural Aluminum
ASTM INTERNATIONAL (ASTM)
ASTM B209M (2014) Standard Specification for Aluminum
and Aluminum-Alloy Sheet and Plate (Metric)
ASTM B221M (2013) Standard Specification for Aluminum
and Aluminum-Alloy Extruded Bars, Rods,
Wire, Profiles, and Tubes (Metric)
KOREAN INDUSTRIAL STANDARDS (KS)
KS D 6701 (2018) Aluminium and Aluminium Alloy
Sheets and Plates, Strips and Coiled Sheets
KS D 6759 (2017) Aluminum and Aluminum Alloy
Extruded Shapes
1.2 SUBMITTALS
Government approval is required for submittals with a "G" designation;
submittals not having a "G" designation are for information only. When
used, a designation following the "G" designation identifies the office
that will review the submittal for the Government. Submittals with an "S"
are for inclusion in the Sustainability eNotebook, in conformance with
Section 01 33 29 SUSTAINABILITY REPORTING. Submit the following in
accordance with Section 01 33 00 SUBMITTAL PROCEDURES:
SECTION 08 91 00 Page 2
CY21 ROKFC IN-KIND A20R210P2, UNACCOMPANIED ENLISTED
PERSONNEL HOUSING (UEPH 100B), USAG HUMPHREYS, KOREA
SD-02 Shop Drawings
Wall Louvers
SD-03 Product Data
Metal Wall Louvers
SD-04 Samples
Wall Louver Samples; G
1.3 DELIVERY, STORAGE, AND PROTECTION
Deliver materials to the site in an undamaged condition. Carefully store
materials off the ground to provide proper ventilation, drainage, and
protection against dampness. Louvers must be free from nicks, scratches,
and blemishes. Replace defective or damaged materials with new.
1.4 DETAIL DRAWINGS
Show all information necessary for fabrication and installation of wall
louvers. Indicate materials, sizes, thicknesses, fastenings, and profiles.
1.5 COLOR SAMPLES
Colors of finishes for wall louver samples must closely approximate colors
indicated. Where color is not indicated, submit the manufacturer's
standard colors to the Contracting Officer for selection.
PART 2 PRODUCTS
2.1 MATERIALS
2.1.1 Aluminum Sheet
ASTM B209M or KS D 6701, alloy 3003 or 5005 with temper as required for
forming.
2.1.2 Extruded Aluminum
ASTM B221M or KS D 6759, alloy 6063-T5 or -T52.
2.2 METAL WALL LOUVERS
Weather resistant type, with bird screens and made to withstand a wind load
of not less than 1.44kilopascals. Wall louvers must bear the AMCA
certified ratings program seal for air performance and water penetration in
accordance with AMCA 500-L and AMCA 511. The rating must show a water
penetration of 0.06 kilograms or less per square meter of free area at a
free velocity of 244 meters per minute.
2.2.1 Extruded Aluminum Louvers
Fabricated of extruded 6063-T5 or -T52 aluminum with a wall thickness of
not less than 2 mm.
SECTION 08 91 00 Page 3
CY21 ROKFC IN-KIND A20R210P2, UNACCOMPANIED ENLISTED
PERSONNEL HOUSING (UEPH 100B), USAG HUMPHREYS, KOREA
2.2.2 Screens and Frames
For aluminum louvers, provide 12.5 mm square mesh, 1.8 or 1.5 mm aluminum or
6 mm square mesh, 1.5 mm aluminum bird screening. For steel louvers,
provide 12.5 mm square mesh, 2.5 or 1.5 mm zinc-coated steel; 12.5 mm
square mesh, 1.5 mm copper; or 6 mm square mesh, 1.5 mm thick zinc-coated
steel or copper bird screening. Mount screens in removable, rewirable
frames of same material and finish as the louvers.
2.3 FASTENERS AND ACCESSORIES
Provide stainless steel screws and fasteners for aluminum louvers and
zinc-coated or stainless steel screws and fasteners for steel louvers.
Provide other accessories as required for complete and proper installation.
2.4 FINISHES
2.4.1 Aluminum
Exposed aluminum surfaces must be factory finished with an anodic coating.
Color must be as indicated. Louvers for each building must have the same
finish.
2.4.1.1 Anodic Coating
Clean exposed aluminum surfaces and provide an anodized finish conforming
to AA DAF45 and AAMA 611. Finish must be:
a. Architectural Class I ( 0.0175 mm or thicker), designation AA-M10-C22-
A42, integral color or A44, electrolytically deposited color anodized.
PART 3 EXECUTION
3.1 INSTALLATION
3.1.1 Wall Louvers
Install using stops or moldings, flanges, strap anchors, or jamb fasteners
as appropriate for the wall construction and in accordance with
manufacturer's recommendations.
3.1.2 Screens and Frames
Attach frames to louvers with screws or bolts.
3.2 PROTECTION FROM CONTACT OF DISSIMILAR MATERIALS
3.2.1 Aluminum
Where aluminum contacts metal other than zinc, paint the dissimilar metal
with a primer and two coats of aluminum paint.
-- End of Section --
SECTION 08 91 00 Page 4
