Technical data sheet SM24A-SR
Modulating damper actuator for adjusting
dampers in technical building installations
• Air damper size up to approx. 4 m²
• Torque motor 20 Nm
• Nominal voltage AC/DC 24 V
• Control modulating 2...10 V
• Position feedback 2...10 V
Technical data
Electrical data Nominal voltage AC/DC 24 V
Nominal voltage frequency 50/60 Hz
Nominal voltage range AC 19.2...28.8 V / DC 19.2...28.8 V
Power consumption in operation 2W
Power consumption in rest position 0.4 W
Power consumption for wire sizing 4 VA
Connection supply / control Cable 1 m, 4x 0.75 mm²
Parallel operation Yes (note the performance data)
Functional data Torque motor 20 Nm
Operating range Y 2...10 V
Input impedance 100 kΩ
Position feedback U 2...10 V
Position feedback U note Max. 1 mA
Position accuracy ±5%
Direction of motion motor selectable with switch 0/1
Direction of motion note Y = 0 V: At switch position 0 (ccw rotation) /
1 (cw rotation)
Manual override with push-button, can be locked
Angle of rotation Max. 95°
Angle of rotation note can be limited on both sides with adjustable
mechanical end stops
Running time motor 150 s / 90°
Sound power level, motor 45 dB(A)
Mechanical interface Universal shaft clamp reversible 10...20 mm
Position indication Mechanical, pluggable
Safety data Protection class IEC/EN III, Safety Extra-Low Voltage (SELV)
Power source UL Class 2 Supply
Degree of protection IEC/EN IP54
Degree of protection NEMA/UL NEMA 2
Enclosure UL Enclosure Type 2
EMC CE according to 2014/30/EU
Low voltage directive CE according to 2006/95/EC
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
www.belimo.com SM24A-SR • en-gb • 2023-08-29 • Subject to change 1/4
Technical data sheet SM24A-SR
Technical data
Safety data UL Approval cULus according to UL60730-1A, UL60730-2-14
and CAN/CSA E60730-1
The UL marking on the actuator depends on
the production site, the device is UL-compliant
in any case
Hygiene test According to VDI 6022 Part 1 / SWKI VA 104-01,
cleanable and disinfectable, low emission
Type of action Type 1
Rated impulse voltage supply / control 0.8 kV
Pollution degree 3
Ambient humidity Max. 95% RH, non-condensing
Ambient temperature -30...50°C [-22...122°F]
Storage temperature -40...80°C [-40...176°F]
Servicing maintenance-free
Weight Weight 0.95 kg
Safety notes
• This device has been designed for use in stationary heating, ventilation and air-conditioning
systems and must not be used outside the specified field of application, especially in aircraft or
in any other airborne means of transport.
• Outdoor application: only possible in case that no (sea) water, snow, ice, insolation or
aggressive gases interfere directly with the device and that it is ensured that the ambient
conditions remain within the thresholds according to the data sheet at any time.
• Only authorised specialists may carry out installation. All applicable legal or institutional
installation regulations must be complied with during installation.
• The device may only be opened at the manufacturer's site. It does not contain any parts that
can be replaced or repaired by the user.
• Cables must not be removed from the device.
• To calculate the torque required, the specifications supplied by the damper manufacturers
concerning the cross-section and the design, as well as the installation situation and the
ventilation conditions must be observed.
• The device contains electrical and electronic components and must not be disposed of as
household refuse. All locally valid regulations and requirements must be observed.
Product features
Mode of operation The actuator is connected with a standard control signal of 0...10 V and drives to the position
defined by the control signal. Measuring voltage U serves for the electrical display of the
damper position 0...100% and as control signal for other actuators.
Simple direct mounting Simple direct mounting on the damper shaft with a universal shaft clamp, supplied with an anti-
rotation device to prevent the actuator from rotating.
Manual override Manual override with push-button possible (the gear train is disengaged for as long as the
button is pressed or remains locked).
Adjustable angle of rotation Adjustable angle of rotation with mechanical end stops.
High functional reliability The actuator is overload protected, requires no limit switches and automatically stops when the
end stop is reached.
Accessories
Electrical accessories Description Type
Auxiliary switch 1x SPDT add-on S1A
www.belimo.com SM24A-SR • en-gb • 2023-08-29 • Subject to change 2/4
Technical data sheet SM24A-SR
Accessories
Description Type
Auxiliary switch 2x SPDT add-on S2A
Feedback potentiometer 140 Ω add-on P140A
Feedback potentiometer 200 Ω add-on P200A
Feedback potentiometer 500 Ω add-on P500A
Feedback potentiometer 1 kΩ add-on P1000A
Feedback potentiometer 2.8 kΩ add-on P2800A
Feedback potentiometer 5 kΩ add-on P5000A
Feedback potentiometer 10 kΩ add-on P10000A
Signal converter voltage/current 100 kΩ 4...20 mA, Supply AC/DC 24 V Z-UIC
Positioner for wall mounting SGA24
Positioner for built-in mounting SGE24
Positioner for front-panel mounting SGF24
Positioner for wall mounting CRP24-B1
Mechanical accessories Description Type
Actuator arm for standard shaft clamp (reversible) AH-20
Shaft extension 240 mm ø20 mm for damper shaft ø12...21 mm CrNi AV12-25-I
Shaft extension 240 mm ø20 mm for damper shaft ø8...22.7 mm AV8-25
Ball joint suitable for damper crank arm KH8 KG8
Ball joint suitable for damper crank arm KH8 / KH10 KG10A
Damper crank arm Slot width 8.2 mm, clamping range ø10...18 mm KH8
Shaft clamp one-sided, clamping range ø8...26 mm, Multipack 20 pcs. K-ENSA
Shaft clamp one-sided, clamping range ø12...26 mm, for CrNi shaft K-ENSA-I
(INOX), Multipack 20 pcs.
Shaft clamp reversible, clamping range ø10...20 mm K-SA
Anti-rotation mechanism 180 mm, Multipack 20 pcs. Z-ARS180
Anti-rotation mechanism 230 mm, Multipack 20 pcs. Z-ARS230
Form fit insert 10x10 mm, Multipack 20 pcs. ZF10-NSA
Form fit insert 12x12 mm, Multipack 20 pcs. ZF12-NSA
Form fit insert 15x15 mm, Multipack 20 pcs. ZF15-NSA
Form fit insert 16x16 mm, Multipack 20 pcs. ZF16-NSA
Mounting kit for linkage operation for flat installation ZG-SMA
Position indicator, Multipack 20 pcs. Z-PI
Baseplate extension for SM..A to SM../AM../SMD24R Z-SMA
Electrical installation
Supply from isolating transformer.
Parallel connection of other actuators possible. Observe the performance data.
Wire colours:
1 = black
2 = red
3 = white
5 = orange
www.belimo.com SM24A-SR • en-gb • 2023-08-29 • Subject to change 3/4
Technical data sheet SM24A-SR
Electrical installation
Wiring diagrams
AC/DC 24 V, modulating
Dimensions
Spindle length
Min. 48
Min. 20
Clamping range
When using a round shaft made of CrNi
(INOX): ø12...20 mm
www.belimo.com SM24A-SR • en-gb • 2023-08-29 • Subject to change 4/4
