Microcomputer Automatic Door Unit

Contents Specification And Performance Parameters

1. Micro-Computer Automatic Door Unit Specification and

Auxiliary light sensor
Power without
12010 12010
Performance Parameters ----------------------------------------------------------- 01
beam device
2. Surface Mounting Power Unit Parts List ---------------------------------------- 02 specifications Auxiliary light sensor 12011 12021

Microcomputer Automatic Door Unit Specification And Performance Parameters

3. Surface-Mounted End-Diagram ----------------------------------------------- 03-04
Door sliding mode Single open Double Open
4. Automatic Door Installation Process --------------------------------------------- 05
≤1*120kg (90) ≤1*130kg (100) ≤2*120kg (90) ≤2*130kg (100)
5. Power Beam Installation ------------------------------------------------------------ 06 Door leaf weight ≤1*150kg (150) ≤2*150kg (150)

6. Power Beam Unit Installation Position of Components - ------------------ 07

Door width 700-1300mm/s(adjustable) 600-1250mm/s(adjustable)
7. Multi-Functional Terminal Port 08
8. The Motor of the Installation - ---------------------------------------------------- 09 Open rate 150-750mm/s(adjustable) 150-680mm/s(adjustable)

9. Controller Device Installation 09

Closing speed 100-680mm/s(adjustable) 100-650mm/s(adjustable)
10. Tension Wheel the Installation --------------------------------------------------- 09
Power outage manually
11. The Door Hanging Body of Work ------------------------------------------------ 10 opening and closing force ≤40N ≤45N

12. Only the Installation-Bit Devices ------------------------------------------------ 11

Control Micro processing controller Micro processing controller
13. Door of the Construction and Installation Height Adjustment ------------ 11
14. Single Open-Belt Installation ----------------------------------------------------- 12 Installation SMT SMT

15. Pairs of Open-Belt Installation 13

Motor 24V55W Brushless DC Motor 24V55W Brushless DC Motor
16. Pairs of Open-Belt Installation (Continued) ----------------------------------- 14
Semi-open feature And it takes another half- And it takes another half-
17. Belt Tension Adjustment ----------------------------------------------------------- 14 open connector open connector
18. Terminal Block the Installation --------------------------------------------------- 15
Door open 0-8 seconds (adjustable) 0-8 seconds (adjustable)
19. Power Lines and Sensor Connection Method ------------------------------- 15
Collision function Under the conditions of a Under the conditions of a
20. Two-Door Interlocking Connections -------------------------------------------- 15 rebound in the collision rebound in the collision
21. The Instructions For Use Remote Control ------------------------------------ 16
Voltage AC200-AC250V 50Hz-60Hz AC200-AC250V 50Hz-60Hz
22. The Sensor Wiring Method 17
23. Security Light and Access Control Wiring Methods ------------------------ 18 Input Current (AC220V pm) 0.095A/1.35A 0.095A/1.35A

24. Action Adjustment --------------------------------------------------------------- 19-22

Operating Temperature -30OC~+50OC -30OC~+50OC
25. Action Description 23
26. Check the Steps 24
27. Abnormal And Diagnostic (Commitment Ago) - ---------------------------- 25

Contents Page 01
 Surface-Mounted Power Unit Parts List Surface-Mounted End-Diagram

Door Open Ty e Door Open Type Single Opening Double-leaf Sectional drawing -90/150
Part Name Part Type Sketch Map Quantity
Surface-Mounted Power Unit Parts List

Surface-Mounted End-Diagram
(90)
1 1

Motor unit 1280906A (150)

1 1

1 1
(100)

Tension wheel equipment 1280801 1 1

Hanger device 1280701 2 4

Belt fixtures 1280601 1 1

Belt fixtures (pairs of open-use) 1280501 1

Single opening(3.2m)
Belt 1280401 1 1
Double-leaf(6.9m)

The devices work only bit 1280301 1 1

Without the security sensors 12802011

Controls 1 1
With safety sensors 12802021

Terminal Device 1280101 1 1

Paste the direction of plate 1730101

Line Card 1730201 1set 4set

1730301 Hex
Hanger bolts 1set 4set
bolt (M8X30)

Belt device installation bolt 1730301 Hex 1set 4set

bolt(M6X12)

Guarantees, instructions 1 1

Page 02 Page 03
 Surface-Mounted End-Diagram Automatic Door Installation Process

Sectional drawing -100 Preparations

Automatic Door Installation Process

Surface-Mounted End-Diagram

Foundation construction

Of the main construction

Automatic Door Construction

The installation of automatic door power plant

The suspension and adjustment of door

Electrical wiring connections

Post-construction inspection

Running adjustments

Adjusted to confirm the status

Delivery

Page 04 Page 05
 Power Beam Installation Power Beam Unit Installation Position
of Components

Cut off power beam size of Single Open

Power Beam Installation

Power beam unit installation position of components

The devices
work only bit
1. Cutting power beam power beam: l = w+a+b-5mm
2. In the power beam, horizontal window or wall drilling.
3. In the power beam and cover the hole.
4. With the power beam bolts fixed to the horizontal window (or wall).

Note: Installation, be sure to make the level of state power beam was installed or
cutting power beam guide do not bumps, other wise it will affect the Double Open
performance or life.

Tension wheel equipment

Power beam construction method

Power beam

Side sealing board

Covering board

Counterstunk self-tapping screw

Page 06 Page 07
 Multi-Functional Terminal Port

Basic shape The Motor of the Installation

1. The motor device in front of lead into the motor.

Multi-Functional Terminal Port

2. The motor unit power beam into the upper groove,

and then let it slip into the lower part of a trench.
1. The program selector switch wiring
3. The motor unit to move to the right end of the
department aluminum beam.
2. Functional wiring at 1 4. Tightening with a screwdriver to install bolts.
3. Auxiliary light wiring department (with Connect wires 5. The motor cable wire through the motor unit above,
auxiliary light sensor) be careful not to make wire sag.

4. Functional wiring division 3

Controller Device Installation

1. The beam power control device into the upper part of

groove, and then slide it the lower part of a trench.
2. Mobile control devices, so that motor unit connection
■ Remote control power output (Note that the remote control can only
access and cannot access other devices) cable can be inserted into the control system device.
■ Normally open mode
3. With a screwdriver tighten the screws on both sides
■ Semi-open model
■ One-way mode
of control devices.
■ Stop locking mode
■ Ground remote control
■ Safety electric eye input (no-voltage contact)
■ The second sensor input (single mode)
■ Two-door interlock output
■ Two-door interlock input
■ Grounding
Tension Wheel the Installation

1. The tensioning wheel unit power beam into the upper

groove, and then let it slip into the lower part of a
■ Back-up power function selection interface trench.
■ GND
2. Wheel with a screwdriver to gently tensioning the
■ Access Controller Power Supply
temporary fixed, so that it can.
■ Access Controller Power Ground
■ Backup Power Ground
■ Anode-lock power output
■ Back-up power supply input (that only use a dedicated power supply)
Installation bolt

Page 08 Page 09
 The Door Hanging Body of Work

1. With the included hanging door hanger device to install the bolt group to the specified
Only the Installation-Bit Devices
location.
1. Screw pine only bit installation of bolts.
The Door Hanging Body of Work

2. The only bit embedded devices unit does power beam rails.
Pylon of the installation locations of
Note: do not hurt electromechanical beam rails.
3. First moving the door body to determine the opening and
● The door frame installation position Only positioner
closing the door body position, and then determine the location of
only the positioner.
【Double Door】 【Single Door】
Security bolts Note: To set only the positioner device location, should enable
the hanger device hit the pad just after the cease-bit device.
4. With hex wrenches really screw fixed installation bolt.
Note: installed carelessly, can cause door damage.

Door of the Construction And Installation Height Adjustment

● Frameless door hanger installation location Hanger device Hanger device
Single Door Double Door

【Double Door】 【Single Door】

Gap Gap

Note: Installation should be to make hanger device pulley center and the door were The order of construction and installation height adjustment
all parallel state (figure), if not parallel, will shorten thepulley life.
Adjustment bolt ● If the door can not be the level of installation, the
2. Screw loose hanger bolt anti de-installation of fixed installation but also off fixtures to door hanger can be adjusted.
Lower Elevated
reduce anti-hanger. 1. The fixed hanger with screw pine nuts.
3. The hanger device pulley linked to the power beam rails. 2. The installation of adjustment bolt to adjust.

Note: Hanging do not bruise the other components within the power beam and ● Clockwise revolving door up.
● Counterclockwise revolving door down.
the guide, otherwise it will result in component failure or pulley life,Noise,
3. Tighten the nut with a fixed hanger.
unusual sounds. Fixed with nut

4. Confirming the lower space and power beam, put

the hanger up anti-off device installed, the gap is 0.5mm.

Hanger Anti-hanger off device Anti-hanger off the installation 5. Confirm the resistance when walking.
Note:Sure the door did not move zhizhong
location of the fixed
henomenon, and there is no friction sound, if
requested to confirm the following:
1. Pylon is vertically fixed on the door.
2. Sway the lower door and the door frame with friction devices.
3. Pylon installations and power beam with friction.
4. The door body and whether there is friction between
Anti-off device installed bolt the door frame.

Page 10 Page 11
 Single Open-Belt Installation Pairs of Open-Belt Installation

Belt fixed the installation steps in Belt fixed the installation steps in
Belt fixtures
1. Remove the screw a to belt fixtures, fittings and Belt fixtures 1. Remove the screw a to belt fixtures, fittings and
Single Open-Belt Installation

Pairs of Open-Belt Installation

Belt connector fittings removed from the belt connector. removed from the belt connector.
2. Reference belt cutting table, cutting belt. 2. Reference belt cutting table, cutting belt.
Screw A 3. The two ends of belt belt fixtures from the center 3. The two ends of belt belt fixtures from the center
of the belt into the belt is indeed a fixed office. of the belt into the belt is indeed a fixed office.
Note: Installed without rendering belt distortion. Note: Installed without rendering belt distortion.
4. The belt fixtures installed on the belt connector 4. The belt fixtures installed on the belt connector
fittings. fittings.
Note: Please note that the direction of belt fixed parts. Note: Please note that the direction of belt fixed
5. The belt first, hang on to the tensioner pulley parts.
wheel device, and then hung to the side of the 5. The belt first, hang on to the tensioner pulley
pulley on the motor unit. wheel device, and then hung to the side of the
6. The belt bolt fixtures. pulley on the motor unit.
Belt bolt fixtures Note: Please be sure to tighten the bolts. 6. The belt bolt fixtures.
Note: Please be sure to tighten the bolts.

Belt fixed the installation location of

Belt connector fittings Belt off the table (Pairs of open)
Belt Length = (DWx3+375) X2 (Unit: mm)

600-1067 Belt Length 6900mm

Belt off the table (single open type)
Belt Length = (DW+375) X2 (Unit: mm)
DW(mm) Belt Length (mm)
600 4100~4150
DW Belt
750 5000~5050
Standard 700-1219 Belt Length 3200mm
800 5300~5350
Special Order 1220-1650 Belt Length 4250mm
850 5600~5650
900 5900~5950
950 5200~6250
DW(mm) Belt Length (mm)
100 6500~6550
762 2274 ~ 2674
1067 6900
800 2350 ~ 2750
850 2450 ~ 2950
900 2550 ~ 3200
950 2650 ~ 3200
951~1219 2750 ~ 3200

Page 12 Page 13
 Pairs of Open-Belt Installation (Continued)

Belt fixed the installation steps in Terminal Block the Installation

1. Adjust the belt tension.
2. So that two door is turned off. 1. Tighten loose bolts installed to terminals inside the
Pairs of Open-Belt Installation /Belt Tension Adjustment

Belt fixtures
3. Removed the double-opening fixtures with a belt device into the power beam.
bolts B,It stationary parts removed from the belt. Note: Please do not damage guides, otherwise shorten
Fixed bolt B
4. The belt fixtures installed belt, ran Post-fixed in the life span caused by the wheels and noise.
pairs to open with a leather belt with parts. 2. The wiring devices to move to the right end of beam
5. The belt bolt fixtures. power.
Note: Please be sure to tighten the bolts. 3. Immediately following the line of the device screw all of
6. Gate locations adjusted to tighten the bolts b. Terminals
the bolts.
Note: Please do not damage guides, otherwise shorten
the life span caused by the wheels and noise.

Power Line and the Sensor Connection Method

1. The power cord and terminal block unit is indeed

Sensor power
supply line connected.
Note: Supply voltage 200-250v, such as pick the wrong

Power Line
power supply voltage may cause fire, electric shock.
Note: Wire stripping head length 10mm, do not come
Belt fixtures installed position (pairs of open type)
across the power terminals outside the office,
Pairs of open-belt connector fittings Signal detection otherwise an electric shock.
line
Belt Fixed connector fittings
Note: Absolutely can not put the power line access to
the sensor input, otherwise it will cause trouble.
2. The sensor power supply and dc24v input connected
to the detection sensors detect the client and the client
Tension wheel equipment
connected.
Note: Please do not greater than the rated current 1a
power supply unit connected to the above,
otherwise they will cause trouble.
Belt Tension Adjustment
1. The tensioning wheel unit to the Two-Door Interlocking Connections
left pull, so that to maintain belt
Adjustment plate bolt
tension, then tighten the four
bolts platen.
2. 4 Adjustable plate fixation screw 1 To 2 controllers and icon link.
loose bolts.
2, It is best to use shielded cable.
3. Along the tension adjustment bolt
clockwise rotation, high-speed Note: Please use 0.5mm2 wire, length 10m below.
belt tension.
Installation bolt
Note: To adjust the front plate
Front panel adjustment
gasket and regulation
Adjustment bolt overlap is appropriate.
Tension adjustment gasket 4. Four adjustable screw plate
Clamp bolt
fixation bolt.

Page 14 Page 15
 The Instructions For Use Remote Control The Sensor Wiring Method

1. According to the direction of plug into Other Way

Connect and Senso
the controller-side panel icon.
2. Pay attention to the direction of plug.
The Instructions For Use Remote Control

The Sensor Wiring Method

Note: Bad connection can cause
adverse movements Signal

Function cancel button Stop locking mode

One-way mode

Normally open mode

(Note that the remote con
Remote control power output
and can not access othe
Normally open mode

Semi-open model Semi-open model

One-way mode
Stop locking mode
Ground remote control
Remote Control Manual Safety electric eye input (no-voltage contact)
● Functional health instructions The second sensor input (single mode)

"A" to stop lock key - role of the door in the closed state (if the installation of automatic Two-door interlock output

mechanical lock, the door Machines will be dual-locking, providing double insurance). Two-door interlock input
Grounding
"B" one-way pass key - role of the door can only accept interior door sensor signal to reach
out not only the purpose of entering one-way passage.
"C" semi-open button - the role of work in the door half-open state, that is, the door opened in a
half open shape.
"D" always open key - role of the door was always kept open state.
Back-up power function selection interface
● Pay attention to matters
GND
1. Remote control can be used normally within 0-20 meters.
Access Controller Power Supply
2. Can not be subject to strong vibration and rain, sun-dried in order to avoid damage caused by
Access Controller Power Ground
Black
remote control.
Backup Power Ground
Red
3. In the remote distances have been shortened or failure, please replace the remote control Anode-lock power output
Power
12V battery. Back-up power supply input (that only use a dedi
Red

Page 16 Page 17
 Security Lighting and Access Control Wiring Methods Action Adjustment

Safety Light Technical Indicators: Belt fixed the installation steps in

Installation height: 0.2 M minimum distance from the ground
The distance between the speed of light: minimum 0.3 M
Security Lighting and Access Control Wiring Methods

Action Adjustment
A: Start edge
Minimum range: 1 M
Maximum range: 5 meters - minimum installation height of 0.2 Meters B: The second sensor switch B: Open Speed

10 Meters - the maximum installation height of 0.4 Meters C: Open the buffer distance
A: Left switch a: Test button
D: Closing speed
b: Signal Indicator
K: Multi-function socket E: Close buffer distance
Black
F: Buffer speed
Gray The speed of light A

Black
C: Locking switch
Gray The speed of light B
G: Opening Hours

A: Test button - action button to adjust the action confirmed

B: Signal indicator - sensors detect signal indicator
A: Left switch - door opening direction selection switch
B: The second sensor switch - a sensor and secondary sensor selector switch
The sensor of a sensor is opened once the signal
Second sensing means to open the door sensor sensing a signal once again to
close the signal sensors
Signal wire C: Closed lock switch - switches appropriated for each closed lock on the left
Note: The above function toggle switch on the power to be effective must be re-

Access Controller
The following is a potentiometer adjustment description:
Swipe card reader
A: Open the time adjustment - power door locks unlock time to adjust after the
Fingerprint
And start the power-conditioning - and start the power-conditioning
B: Open the speed - the speed knob to adjust door open
C: Open the buffer distance - the distance adjusting knob door buffer
D: Closing speed - a knob to adjust the closing speed of

Electric Lock Backup Power E: Close buffer distance - the distance adjusting knob to close the buffer
F: Buffer speed - the speed knob to adjust the buffer
G: Opening hours - opening hours adjustment knob
K: Multi-function socket - two-door interlocking connectors

Page 18 Page 19
 Action Adjustment(Continued) Action Adjustment(Continued)

Adjustment procedure (adjusted before the door shut manually Adjustment procedure (adjusted before the door shut manually
several times to confirm the door is smooth switch.) several times to confirm the door is smooth switch.)
Action Adjustment

Action Adjustment
Open
Set around switch
Speed Buffer Distance

Opening speed

Buffer Distance
Switching around From the inside view, according to the direction of
Doors open to the right the door opening, set the left or right.
For the double-door, the switch setting around. Travel
Lift Right
Minimum Maximum Minimum Maximum Closed position Open position

Accesses
Press the test button on control devices, the switch door, adjust door speed, door
buffer distance.
Inside Door Note: When the use of electronic locks, please use the test button after unlocking.
Aluminum beam inside
Note: Please confirm there is no pedestrians around the door after the adjustment, or
vulnerable to injuries.
1. Opened the door to confirm whether the rate and buffer in the middle distance is in
Set sensor mode, when the switch on the right time, in a sense
the middle (factory set value).
manner, on the left, for the Secondary induction method. 2. Adjust the door buffering distance from its set to 10cm.
Note: Adjustment, be sure to slowly carried out, such as the large rotary knob, the

When the door is closed after the turn the power switch. door will cause personnel or damage the body.
3. Adjust the speed door.
4. Confirm the open door, after the speed, if necessary, open the door for further
To open the door to low-speed direction Daotou, stop in open adjustment of the buffer distance.
position, and to factory settings the speed of closure. Note: Do not switch on the door during the adjustment. Please take your time to
adjust. If large rotating knob, the door will cause personal injury or damage the body.
Note: A buffer distance must be set to open more than 5cm. Otherwise, the door will
Start power adjustment. cause personal injury or physical damage.

Start force Start power adjustment.

Start force

Press the test button on control devices, the

switch door, adjust the boot edge.
Press the test button on control devices, the
Note: When the use of electronic locks, please
switch door, adjust the boot edge.
Minimum Maximum use the test button after unlocking.
Note: When the use of electronic locks, please
Minimum Maximum use the test button after unlocking.

Page 20 Page 21
 Action Adjustment(Continued) Action Description

Adjustment procedure (adjusted before the door shut manually Simulation Action
several times to confirm the door is smooth switch.)

Action Description
Action Adjustment

Close

Speed Buffer Distance

Buffer Distance

Closing speed
Note: Connected to carry out the above immediately after the power moves, has nothing to
do with the full-half open.
Travel
Minimum Maximum Minimum Maximum Closed position Open position
The use of semi-open model

Press the test button on control devices, the switch door, adjust door speed, door
buffer distance.
Note: When the use of electronic locks, please use the test button after unlocking.
Note: Please confirm there is no pedestrians around the door after the adjustment, or Note: In the first test signal to open to open and were open state = confirmed half-open
vulnerable to injuries. position, as the imposition of outside force to imitate people hit the door, it is easy to
1. To confirm whether the rate of closing the distance in the middle and the buffer is in confirm the wrong location, please note.
the middle (factory set value).
2. Adjust the door buffering distance from its set to 10cm. Normal Operation
Note: Adjustment, be sure to slowly carried out, such as the large rotary knob, the
door will cause personnel or damage the body.
3. Adjust the speed door.
4. Confirm the open door, after the speed, if necessary, open the door for further
adjustment of the buffer distance.
Note: Do not switch on the door during the adjustment. Please take your time to Collision Detection Function
adjust. If large rotating knob, the door will cause personal injury or damage the body. ● In the closing movement in the case of obstacle was conducted after the rebound.
Note: A buffer distance must be set to open more than 5cm. Otherwise, the door will ● Encounter obstacles to rebound after the door is closed before the trip to the obstruction site
cause personal injury or physical damage. into a buffer speed.
● In case of barrier material removed, the door to confirm the next start after returning to
Adjustments are hold time normal.

Start force
Protection Function
● Control devices which have self-protection, to the inside temperature rises to a certain value,
the opening hours is automatically set to maximum.
● If the temperature continues to rise, then automatically stop working, such as temperature
Press the test button on control devices, the declines, then automatically return to normal.
switch door, adjust the opening hours.
Note: When the use of electronic locks, please
Minimum Maximum use the test button after unlocking.

Page 22 Page 23
 Check the Steps Abnormalities and Diagnosis (Commitment Ago)

Automatic door does not move, please press the plan step to A anomalies Reason Confirmed that the matter Approach

be checked Do not switch too ● Turned on or off too slowly. Confirmed that the door switch Adjust the switching
slow or non-smooth ● Too much distance between settings. speed of the value of the
Check the Steps

Abnormalities and Diagnosis (Commitment Ago)

the buffer. Cut off the power supply, hand- door.
● Some people run into the switch door. Adjust the buffer settings.
door when the door switch Confirmed and whether the litter So that the temporary
body or foreign body caused rail. closure of a door.
(1) The door and door-side by abnormal pattern. To confirm whether there are any Garbage removal.
● Walking too much resistance. obstacles. Removal of obstructions.
columns or beams are not
Power off Unbalanced
working.
Hand sliding doors Doors which do not ● Power supply is not See circuit breaker. Connected to circuit
(2) rails too much dust.
move connected. See the power switch is turned breakers.
(3) had rounds of disabilities.
● Sensor fault. on. Open the power switch.
(4) door distortion. ● Power supply is not See if the door was locked. Replace the sensor.
(5) faulty lock or door keys. connected. Turn off the power to confirm Open the door.
(6) improper installation or ● Door locked. whether the smooth door Remove litter or
Smooth ● Door rail there garbage. movement. obstructions.
adjustment.
View connection. Reconnected or
replaced.

The door does not ● Sensors continue to work. There are moving objects in the Moving object in the
Check electrical wiring
close ● Safety sensors continue to sensing region cause an error sensing region.
work. action. Replace the sensor.
● Sensor signal line short- There is no moving object in the Garbage removal.
Normal circuit. sensing region cause an error Optical axis alignment.
action. Replace the signal line.
Check the safety photoelectric
light receiver on the head or
rubbish.
Optical axis easy road.
Check sensor problems:
Connected to the power. Doors move smoothly Remove the terminals on the
(1) sensor failure or malfunction. signal line, the door is closed.
Press the TEST button
(2) sensor wire cut or short-circuit.
on the controller.
Door will automatically ● Sensor malfunction. Check The moving object away
switch 1. testing whether there are Check from the test area.
moving objects in the region. Check To send a strong wave
2. the door near a strong Check of the machine away.
Doors movements are not smooth radio waves. Sensor rebound phenomenon. Conversion tamper
3. and other sensors detect switch.
areas overlap. The lamp away from the
4. testing the area with test area.
fluorescent lights. Replace the sensor.
Power beam device has problems: ● Sensor bad.
(1) Connector poor contact.
Failure to open the Check full / half-width of the
(2) Controller problems. Set in the semi-open model Switch to full-mode
door door open switch

Starting torque are set

Doors Jitter Set Starting Torque
incorrectly.

Page 24 Page 25
●Specifications Subject To Change Without Notice