As-Built Checklist for Ferrari 330 GTC/GTS
This list identifies important items that need to be present to meet 330 GTC original build configuration when the
car left the factory. This list is not intended to identify all the areas that are observed during the IAC/PFA judging
process. Additional original build configuration details are described in the 330 GTC/GTS As-Built Configuration and
Judging Notes Document, Version 8.0, July 2023. However, it is possible that a car may have been built with variations of
the items as described in this list and should be documented in the cars factory build sheet. There is no assurance that
constructing a car as defined in this document will result in an award at a judged Concours event.
Version 8 July 2023
EXTERIOR
Item Should Be
1 Rubber boot over front Black rubber boot with wires protruding from the top of the boot
running/turn signal light
2 Protective Pan under radiator Fiberglass pan under radiator painted satin black
3 Molding on pinch weld under trunk Rubber molding with approx. 35 very- fine rubber ridges terminated with a
area stainless clip and flathead Philips machine screw
4 Windshield wipers Windshield wipers were wire formed frames made by Lucas or Carello
5 Rubber weather strip molding at Specially shaped black rubber seal piece at the bottom of the windshield pillar
bottom of windshield pillar held in place to the body with 3/32 pop rivets with flat washers visible under
the pop rivet.
6 Mounting front running lights and Lights are mounted with chrome, truss head, slotted machine screws
rear backup lights
7 Hood, door, and trunk panel gaps Body gaps should be even and aligned, chrome not dented or degraded,
and fit, condition of paint, chrome, rubber seals not cracked or torn, paint chips on nose acceptable
and glass
INTERIOR
Item Should Be
1 Headliner and trim Headliner, sun visor and all trim pieces above window level should be cream
colored. Black vinyl on rear parcel shelf, windshield pillar, B pillar, center
console, dash, and arm rest, independent of seat and door panel color.
2 Sun visor and rearview mirror The sun visors are heat sealed along the edge, not sewn. White rubber tips on
sun visor arm, a day/night lever on bottom of rearview mirror.
3 Rear parcel shelf The rear parcel shelf should be covered in black vinyl with a punched hole
pattern for speakers (with or without radio). The gas lever release knob is fan
shaped with surround bezel. Early cars may not have the bezel.
4 Trim on front of the doors Early cars had rubber molding trim; later cars had chrome trim.
5 Door striker bracket Door striker bracket (CAD) is mounted with two CAD plated, flat, Allen head
machine screws, not Phillips head screws.
6 Floor heel mats Driver and passenger heel mats should be black rubber with a small basket
weave pattern. Should not be a heel mat on the firewall on passenger side.
7 Emergency window crank Emergency window crank uses an access hole in the door panel to operate the
window lift mechanism. Usually stored in the glove box.
8 Luggage straps Two leather luggage straps attached to the rear parcel shelf and luggage shelf
bottom with chrome footman brackets. The straps are black leather on the
Page 1 of 10
front side of the strap and a tan color on the back side, independent of the
interior leather colors. The belt buckles should be nickel plated, not chrome
plated.
10 Seatback rest stop Rubber stop for seatback to rest on. Shape my vary from picture.
11 Tools Tool bags (1 or 2 bags) with period correct tools. Early cars may have had one
tool bag with many more tools and later cars had 2 tool bags with a reduced
set of tools. Tools should be period correct.
12 Jack and manuals Battaini jack painted blue or yellow, Owner’s pouch, Owner’s Manual and
Parts book (reproductions acceptable)
13 Spare wheel and tire The spare wheel and tire should match the wheels and tires on the car unless
the spare is an original wheel and tire. The spare tire is held in place by a large
chrome ring with a T- handled bolt
ENGINE AND CHASSIS
Item Should Be
1 Hose clamps There can be 4 different hose clamps used for water, fuel, vacuum, and fluid
lines. Cheney, Copiglia band clamp and black oxide Corbin spring clamp were
most commonly used. The Angst clamp was seen in place of the Copiglia and
Corbin clamps on some later production cars.
2 Cable ties and screws Cable ties are metal, no zip ties, twist ties or tape. Pininfarina used oval and
flat head Phillips screws. Exceptions are the slotted screws securing the shift
gate plate, Allen head securing the door striker, and the truss head screw
securing the front running lights and the rear backup lights .
3 Engine bay surround molding A smooth, dark polypropylene material with a square edge on the top with a
rectangular cross section. The molding should not be rubber or cloth covered.
4 Wheels and tires Two wheel options. 14x7-inch Borrani wire wheel, RW4039, with angled, 3
eared, chrome knockoff with a prancing horse in the center. or 14-inch
Campagnolo cast alloy , 10-hole wheel with a straight, square ended, 3 eared
chrome knockoff with a prancing horse in the center. Should not be a Borrani
logo in the center of the knockoff. Tires should be 205 HR 14 or 205 VR 14
5 Steering Idler The steering idler assembly cap should be natural bronze with a dark oxidized
appearance. The retaining nuts should be silver CAD with yellow inserts.
6 Valve cover and heat shield The valve covers and exhaust header heat shields should be black crinkle paint.
The Ferrari name should be the same color and texture as the valve cover.
Heat shield secured with black oxide Lobo bolts and large flat washers.
7 Carburetor mounting and Four special black oxide 12mm nuts and wave washers mounting each
throttle bell crank shaft bearing carburetor to the manifold. Throttle bellcrank bearings painted black crinkle
retained with black oxide nuts and washers. Bellcrank rod finish is black oxide.
8 Air filter breather hose and clamp The filter breather hoses on the PVC systems should be semi clear or
transparent green polyurethane tubing retained with black oxide Corbin spring
clamps. Heat and age may alter the color of the tubing. Angst clamps have
been seen on later cars.
Page 2 of 10
9 Water heater hose and clamps Water heater hoses are cloth covered or cloth covered appearance, secured
with Copiglia band clamps. If stickers are on the hose, should be Safta Calore
sticker, not Pirelli.
10 Steering column The steering column painted satin black up to the U-joint. The U-joint should
have a raw, case-hardened, steel finish (may be clear coated to preserve
finish), the coupler from the U-joint to the shaft into the steering box should
be black oxide, and the shaft into the steering box should be natural steel with
a bright finish. Black mechanic’s wire should be used to safety wire the black
oxide bolts on the U-joint.
11 Brake and Clutch master Early cars (prior to around S/N 10000) had a Dunlop brake system with brake
cylinders, hoses, and clamps booster painted semigloss black, the clutch master cylinder natural aluminum
and brake master cylinder CAD plated. Later cars had a Bonaldi brake system
with the brake booster plated gold CAD, the clutch master cylinder natural
aluminum and the brake master cylinder painted satin black with a CAD plug
on the end. Clutch and brake fluid hoses should be smooth rubber secured
with black oxide Corbin spring clamps. Later cars had a mechanical clutch,
eliminating the clutch fluid reservoir.
12 Alternator wiring junction box A black plastic electrical wiring junction box mounted on the left side of the
engine bay to connect the Lucas alternator wiring.
13 Spark plug wires and routing 2 rubber O-rings and a bracket mounted on the distributor to gather the black,
7 mm, spark plug wires from the distributor, exiting the round, tapered metal
distribution tube through rubber grommets. Metal tube should be painted
crinkle black.
14 Radiator cap, overflow hose and Silver CAD 2-eared, non-pressure radiator cap, ribbed rubber overflow hose
expansion tank and 5mm Copiglia clamp. Expansion tank painted satin black with two earned,
CAD .9 BAR pressure cap. Copiglia clamps on ribbed hoses.
15 Radiator cooling fan motor Square body Lucas motor painted gray/green hammer tone with natural
aluminum or painted black satin, 3 bladed fan.
16 Exhaust system, exhaust tip Made by Ceretto, Galetti, or Spacem. ANSA decals are not correct for the 330
GTC
17 Fiamm compressor cover A satin black plastic can houses the Fiamm air compressor in the right side of
the front nose
18 Battery cable termination, A right-angle connector on + and – terminal. + terminal should have a rubber
copper ground strap cover. Should be a braided copper ground strap from battery mounting
bracket to the engine block
19 Air Conditioning System York compressor with black, black cloth covered AC hoses terminated with
Aeroquip connectors. The preferred finish for the compressor is aluminum.
20 Rust, corrosion, oil, and water Check for rust, corrosion, oil, and water leaks in the engine bay
leaks
EXTERIOR PICTURES
Page 3 of 10
1) Rubber boot covering running light 2) Protective pan under radiator 3) Ribbed molding on trunk pinch weld
4) Wire formed wipers 5) Rubber weather molding 6) chrome truss head screw
INTERIOR PICTURES
1) Head liner and trim 2) Sun visor rubber tips 3) Speaker holes on rear parcel shelf
Page 4 of 10
4) rubber molding on door 4) chrome molding on door 5) door striker , Allen head screws
6) Heel pad pattern 7) Emergency window crank 8) Luggage strap
10) Seatback rest stop 11) 2 tool bags 11) example tools for late car
Page 5 of 10
11) Owner’s manual picture, early car tools 12) Battaini Jack 12) Owners pouch and manuals
ENGINE AND CHASSIS PICTURES
1)Cheney clamp 1) Copiglia and Corbin clamp 1) Angst clamp
2)Ties, nuts, screws, fiber washer 3) Engine bay surround 4) Boranni wire wheel
Page 6 of 10
4) Campagnolo cast alloy wheel 5) steering idler 6) valve cover and heat shield
7) Carb nuts and bellcrank bearing 8) Air breather hose and Corbin clamp 9) Water heater hose and Copiglia clamp
10) Steering column 11) Dunlop brake system
Page 7 of 10
11) Bonaldi brake system 12) Alternator junction box 13) Plug wire routing,
14) Radiator cap, hose,Copglia clamp 15) Lucas square radiator fan motor 16) Ceretto exhaust tip
17) Fiamm compressor cover 18) Right angle batter cable connector 18) Copper ground strap
Page 8 of 10
19) Black cloth covered AC hose and Aeroquip connectors
Page 9 of 10
Page 10 of 10
