VRF Multi-split Air Conditioning System

SET-FREE FSN2 Indoor Units

INVERTER-DRIVEN MULTI-SPLIT SYSTEM Heat Pump Air Conditioners

INVERTER-DRIVEN MULTI-SPLIT SYSTEM Heat Pump Air Conditioners

Models
Indoor Units
In-the-Ceiling Type
RPI-0.8FSN2 RPI-1.0FSN2 RPI-1.5FSN2
Technical Catalogue RPI-2.0FSN2 RPI-2.5FSN2 RPI-3.0FSN2
RPI-4.0FSN2 RPI-5.0FSN2
for Indoor Unit RPI-8FSN RPI-10FSN
4-Way Cassette Type
RCI-1.0FSN2 RCI-1.5FSN2 RCI-2.0FSN2
RCI-2.5FSN2 RCI-3.0FSN2 RCI-4.0FSN2
RCI-5.0FSN2
2-Way Cassette Type
RCD-1.0FSN2 RCD-1.5FSN2 RCD-2.0FSN2
RCD-2.5FSN2 RCD-3.0FSN2 RCD-4.0FSN2
RCD-5.0FSN2
Wall Type
RPK-1.0FSNSM2 RPK-1.5FSNSM2 RPK-2.0FSNSM2
RPK-2.5FSNSM2 RPK-3.0FSNSM2 RPK-4.0FSNSM2
Floor Type
RPF-1.0FSN2E RPF-1.5FSN2E
Floor Concealed Type
RPFI-1.0FSN2E RPFI-1.5FSN2E
Ceiling Type
RPC-2.0FSN2 RPC-2.5FSN2 RPC-3.0FSN2
RPC-4.0FSN2 RPC-5.0FSN2
System Equipment
Total Heat Exchangers
KPI-2521 KPI-5021 KPI-8021 KPI-10021

SET-FREE FSN2 Indoor Units

 TIPS ON ENERGY EFFICIENT VRF DESIGN

TIP No 1:

Shorter pipe run will

minimize capacity loss
and reduce refrigerant
charge in system.

TIP No 2:

Take advantage
of diversity factor
will reduce your
initial capital as
well as ongoing
running cost.

TIP No 3:

Each zone served

by dedicated
unit will help to
increase comfort
level and reduce
Energy waste.
 TIPS ON ENERGY EFFICIENT VRF DESIGN

TIP No 4:

Heat recovery system will

not only provide simultaneous
cooling and heating, but also
recover energy that would
be lost in traditional system.

TIP No 5:

Having minimum
Change Over box in same
zone will prevent units
from fighting against each
others and save energy.

TIP No 6:

Unbalanced selection
will cause small unit
starve from Refrigerant
and run longer than
it should be.
 CONTENTS
Technical Data

Items Page
1. Features 1-5
1.1 System Features 1-5
1.2 Features on Indoor Unit 1-12
1.2.1 In-the-Ceiling Type 1-12
1.2.2 4-Way Cassette Type 1-13
1.2.3 2-Way Cassette Type 1-16
1.2.4 Wall Type 1-18
1.2.5 Floor Type 1-20
1.2.6 Floor Concealed Type 1-20
1.2.7 Ceiling Type 1-21
1.3 Features on Total Heat Exchangers 1-22
1.4 Features on Optional Liquid Crystal Remote Control Switch,
Wireless Remote Control Switch, Half Size Remote Control Switch, 1-23
7-Day Timer and Central Stations
1.4.1 Lineup 1-23
1.4.2 Liquid Crystal Remote Control Switch, PC-AR (Optional) 1-23
1.4.3 Wireless Remote Control Switch, PC-LH3A (Optional) 1-25
1.4.4 Half Size Remote Control Switch, PC-ARH (Optional) 1-26
1.4.5 7-Day Timer, PSC-A1T (Optional) 1-27
1.4.6 Central Station, PSC-5S (Optional) and PSC-A64S (Optional) 1-28
1.4.7 Centralized ON/OFF Controller, PSC-A16RS (Optional) 1-30
2. General Data 1-31
3. Dimensional Data 1-43
3.1 Dimensional Data for Indoor Units 1-43
3.2 Dimensional Data for Total Heat Exchangers 1-56
4. Selection Data 1-57
4.1 Operation Space 1-57
4.2 Selection Guide 1-60
4.3 Sensible Heat Factor (SHF) 1-62
4.4 Fan Performance 1-63
4.5 Model Selection of Total Heat Exchangers 1-68
5. Electrical Data 1-72
6. Sound Data 1-74
7. Working Range 1-87

iv
 CONTENTS
Technical Data
Items Page
8. Optional Accessories 1-88
8.1 for Control Systems 1-88
8.1.1 Liquid Crystal Remote Control Switch (PC-AR) 1-88
8.1.2 Wireless Remote Control Switch (PC-LH3A) 1-88
8.1.3 Half Size Remote Control Switch (PC-ARH) 1-88
8.1.4 7-Day Timer (PSC-A1T) 1-88
8.1.5 Central Station (PSC-5S and PSC-A64S) 1-89
8.1.6 Centralized ON/OFF Controller (PSC-A16RS) 1-93
8.1.7 Receiver Kit (PC-ALH, PC-ALHD, PC-ALHP and PC-ALHZ) 1-93
8.1.8 Remote Control Cable <for PC-AR>
1-93
(PRC-5K, PRC-10K and PRC-15K)
8.1.9 3P Connector Cable (PCC-1A) 1-93
8.1.10 Remote Sensor (THM-R2A) 1-93
8.2 for Indoor Units 1-94
8.2.1 for In-the-Ceiling Type 1-94
8.2.2 for 4-Way Cassette Type 1-98
8.2.3 for 2-Way Cassette Type 1-109
9. Component Data 1-117
10. Control System 1-124
10.1 Refrigeration Cycle 1-124
10.2 System Control 1-130
10.2.1 Control in a Room 1-130
10.2.2 Group Control from a Remote Place 1-131
10.2.3 Control in a Room/Control from a Remote Place 1-131
10.3 Standard Operation Sequence 1-132
10.4 Safety and Control Device Setting 1-138
10.5 Optional Dip Switch Setting for Capacity Adjustment 1-138
10 6 Electrical
10.6 El t i l Wiring
Wi i Diagram
Di 1-139
1 139
11. Miscellaneous Notes 1-149
12. Standard Specifications 1-151A-B-C
1-151

v
 CONTENTS
Installation and Operation
Page

Items Indoor Unit Type

RPI RPI RPF
RCI RCD RPK RPC
(0.8 to 5.0HP) (8 and 10HP) RPFI
1. Safety Summary 2-5 2-19 2-31 2-43 2-55 2-73 2-83
2. Structure 2-5 2-19 2-31 2-43 2-55 2-73 2-83
2.1 Indoor Unit 2-5 2-19 2-31 2-43 2-55 2-73 2-83
2.2 Refrigerant Cycle 2-7 2-20 2-32 2-44 2-58 2-74 2-84
2.3 Necessary Tools and
2-7 2-20 2-32 2-44 2-58 2-74 2-84
Instruments List for Installation
3. Transportation and Handling 2-7 2-20 2-32 2-44 2-58 2-74 2-84
3.1 Transportation 2-7 2-20 2-32 2-44 2-58 2-74 2-84
3.2 Handling of Indoor Unit 2-7 2-20 2-32 2-44 2-58 2-74 2-84
4. Indoor Unit Installation 2-7 2-21 2-33 2-45 2-59 2-75 2-85
4.1 Factory-Supplied Accessories 2-7 2-21 2-33 2-45 2-59 2-75 2-85
4.2 Initial Check 2-9 2-22 2-34 2-46 2-60 2-76 2-86
4.3 Installation 2-10 2-23 2-35 2-47 2-62 2-77 2-87
5. Refrigerant Piping Work 2-13 2-25 2-37 2-49 2-67 2-78 2-88
5.1 Piping Materials 2-13 2-25 2-37 2-49 2-67 2-78 2-88
5.2 Piping Connection 2-13 2-25 2-37 2-49 2-67 2-78 2-88
6. Drain Piping 2-14 2-27 2-38 2-50 2-69 2-79 2-90
7. Electrical Wiring 2-15 2-28 2-40 2-52 2-70 2-80 2-91
7.1 General Check 2-15 2-28 2-40 2-52 2-70 2-80 2-92
7.2 Electrical Wiring Connection 2-15 2-28 2-40 2-52 2-70 2-80 2-92
8. Test Run 2-17 2-30 2-42 2-54 2-72 2-82 2-93
9. Safety and Control Device Setting 2-17 2-30 2-42 2-54 2-72 2-82 2-93
10. Common 2-95
10.1 Field Minimum Wire Size for
2-95
Power Source
10.2 Setting of Dip Switches 2-96
10.3 Setting the Filter Indication Interval 2-101
10.4 Setting of High Speed Tap 2-102
10.5 Setting of External Pressure 2-102

vi
 CONTENTS
Installation and Operation

Items Page
11. Installation of Optional Air Panel 2-103
11.1 Air Panel for 4-Way Cassette Type: P-N23WA 2-103
11.2 Air Panel for 2-Way Cassette Type: P-N23DWA and P-N46DWA 2-108
12. Installation of Optional Controller 2-113
12.1 Remote Control Switch : PC-AR 2-114
12.2 Wireless Remote Control Switch: PC-LH3A 2-132
12.3 7-Day Timer : PSC-A1T 2-137
12.4 Central Station: PSC-5S 2-151
12.5 Central Station: PSC-A64S 2-169
12.6 Centralized ON/OFF Controller: PSC-A16RS 2-192
12.7 Wireless Receiver Kit: PC-ALH (for 4-Way Cassette Type) 2-204
12.8 Wireless Receiver Kit: PC-ALHD, PC-ALHP and PC-ALHZ
(for 2-Way Cassette Type, Ceiling Type, In-the-Ceiling Type, 2-210
Floor Type, Floor Concealed Type and Wall Type)
13. Total Heat Exchanger 2-220
13.1 Safety Summary 2-220
13.2 Structure 2-220
13.3 Transportation and Handling 2-221
13.4 Installation 2-221
13.5 Electrical Wiring 2-225
13.6 Test Run 2-232
13.7 Safety and Control Device Setting 2-232
14. Maintenance 2-233
15. Operation 2-234
15.1 Remote Control Switch 2-234
15.2 Before Operation 2-236
15.3 Operation Method 2-236
15.4 Setting of Automatic Swing Louver Direction 2-237
15.5 Automatic Control 2-244
15.6 Identifying of Indoor Units Installed Side by Side 2-245
15.7 Filter Cleaning 2-246
15.8 Filter and Element Cleaning for Total Heat Exchanger 2-249
15.9 Replacing Batteries for Wireless Remote Control Switch 2-250
16. Troubleshooting 2-251
16.1 Initial Troubleshooting 2-251
16.2 Troubleshooting by Alarm Code 2-252
16.3 Troubleshooting in Check Mode by Remote Control Switch 2-254
16.4 Self-Checking of PCB using Remote Control Switch 2-260
16.5 Self-Checking of Remote Control Switch 2-262

vii
TECHNICAL DATA
 GENERAL DATA

2. General Data

Indoor Unit Type In-the-Ceiling Type

Model RPI-0.8FSN2 RPI-1.0FSN2 RPI-1.5FSN2 RPI-2.0FSN2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 2.3 2.9 4.1 5.8
Capacity *1) kcal/h 2,000 2,500 3,550 5,000
Btu/h 7,900 9,900 14,100 19,800
Nominal Cooling kW 2.2 2.8 4.0 5.6
Capacity *2) kcal/h 1,900 2,400 3,400 4,800
Btu/h 7,500 9,600 13,600 19,100
Nominal Heating kW 2.5 3.2 4.8 6.3
Capacity kcal/h 2,100 2,800 4,100 5,400
Btu/h 8,500 10,900 16,400 21,500
Sound Pressure Level
(Overall A Scale) dB 35-33-31 35-33-31 35-33-31 35-33-31
Outer Dimensions
Height mm 270 270 270 270
(in.) (10-5/8) (10-5/8) (10-5/8) (10-5/8)
Width mm 650+75 650+75 650+75 900+75
(in.) (25-9/16+2-15/16) (25-9/16+2-15/16) (25-9/16+2-15/16) (35-7/16+2-15/16)
Depth mm 720 720 720 720
(in.) (28-3/8) (28-3/8) (28-3/8) (28-3/8)
Net Weight kg 26 26 26 35
(lbs.) (57) (57) (57) (77)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 8/7/6 8/7/6 13/11/9 15/13/11
(Hi/Me/Lo) (cfm) (283/247/212) (283/247/212) (459/388/318) (530/459/388)
External Pressure *3) Pa 50 (80-30) 50 (80-30) 50 (80-30) 50 (80-30)
Motor W 60 60 60 75
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
6.35
6.35
6.35
6.35
(in.) (1/4) (1/4) (1/4) (1/4)
Gas Line mm
12.7
12.7
12.7
15.88
(in.) (1/2) (1/2) (1/2) (5/8)
Condensate Drain VP25 VP25 VP25 VP25
Approximate
Packing Measurement m3 0.21 0.21 0.21 0.27
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1.5 Meter Beneath the Unit.
With Discharge Duct (2.0m) and Return Duct (1.0m).
Voltage of the power source for the indoor fan motor is 220V.
In case of the power source of 240V, the sound pressure level increases by about 1 dB.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.
3. The data for external pressure *3) indicates "Standard Pressure Setting (High Pressure Setting - Low Pressure Setting)"
values when a filter is not used.
The sound pressure level is based on the Standard Pressure Setting.

1-31
 GENERAL DATA

Indoor Unit Type In-the-Ceiling Type

Model RPI-2.5FSN2 RPI-3.0FSN2 RPI-4.0FSN2 RPI-5.0FSN2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 7.3 8.3 11.6 14.5
Capacity *1) kcal/h 6,300 7,100 10,000 12,500
Btu/h 25,000 28,200 39,700 49,600
Nominal Cooling kW 7.1 8.0 11.2 14.0
Capacity *2) kcal/h 6,100 6,900 9,600 12,000
Btu/h 24,200 27,300 38,200 47,800
Nominal Heating kW 8.5 9.0 12.5 16.0
Capacity kcal/h 7,300 7,700 10,700 13,800
Btu/h 29,000 30,700 42,600 54,600
Sound Pressure Level
(Overall A Scale) dB 36-34-32 42-39-35 43-40-36 44-41-37
Outer Dimensions
Height mm 270 350 350 350
(in.) (10-5/8) (13-3/4) (13-3/4) (13-3/4)
Width mm 900+75 650+75 900+75 1,300+75
(in.) (35-7/16+2-15/16) (25-9/16+2-15/16) (35-7/16+2-15/16) (51-3/16+2-15/16)
Depth mm 720 800 800 800
(in.) (28-3/8) (31-1/2) (31-1/2) (31-1/2)
Net Weight kg 35 37 46 58
(lbs.) (77) (82) (101) (128)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 16/14/12 19/17/14 27/23/19 37/31/25
(Hi/Me/Lo) (cfm) (565/494/424) (671/600/494) (954/812/671) (1,306/1,095/883)
External Pressure *3) Pa 50 (80-30) 120 (170-60) 120 (170-60) 120 (170-60)
Motor W 75 150 290 290
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
9.53
9.53
9.53
9.53
(in.) (3/8) (3/8) (3/8) (3/8)
Gas Line mm
15.88
15.88
15.88 *4

15.88 *4)
(in.) (5/8) (5/8) (5/8) (5/8)
Condensate Drain VP25 VP25 VP25 VP25
Approximate
Packing Measurement m3 0.27 0.29 0.38 0.52
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1.5 Meters Beneath the Unit.
With Discharge Duct (2.0m) and Return Duct (1.0m).
Voltage of the power source for the indoor fan motor is 220V.
In case of the power source of 240V, the sound pressure level increases by about 1 or 2 dB.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.
3. The data for external pressure *3) indicates "Standard Pressure Setting (High Pressure Setting - Low Pressure Setting)"
values when a filter is not used.
The sound pressure level is based on the Standard Pressure Setting.
4. *4) In case of using R407C or R22, use the accessory adaptor and
19.05 piping.

1-32
 GENERAL DATA

Indoor Unit Type In-the-Ceiling Type

Model RPI-8FSN RPI-10FSN
Indoor Unit Power Supply AC 3
4W, 380-415V/50Hz, 380V/60Hz
Nominal Cooling kW 23.3 29.1
Capacity *1) kcal/h 20,000 25,000
Btu/h 79,400 99,200
Nominal Cooling kW 22.4 28.0
Capacity *2) kcal/h 19,300 24,100
Btu/h 76,400 95,500
Nominal Heating kW 25.0 31.5
Capacity kcal/h 21,500 27,100
Btu/h 85,300 107,500
Sound Pressure Level
(Overall A Scale) *3) dB 45 (42)* 52 (50)*
Outer Dimensions
Height mm 470 470
(in.) (18-1/2) (18-1/2)
Width mm 1,250 1,250
(in.) (49-1/4) (49-1/4)
Depth mm 1,120 1,120
(in.) (44-1/12) (44-1/12)
Net Weight kg 100 100
(lbs.) (221) (221)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 58 (58)* 72 (72)*
(cfm) (2,048 (2,048)*) (2,542 (2,542)*)
External Pressure *4)
380/415V Pa 220 (110)* / 260 (130)* 220 (110)* / 260 (130)*
Motor kW 0.76 (0.51)* 1.08 (0.81)*
Connections Brazing Connection
Refrigerant Piping
Liquid Line mm
9.53 *5)
9.53 *5)
(in.) (3/8) (3/8)
Gas Line mm
19.05 *6)
22.2 *7)
(in.) (3/4) (7/8)
Condensate Drain VP25 VP25
Approximate
Packing Measurement m3 1.06 1.06
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level *3) is based on following conditions.
1.5 Meters Beneath the Unit.
With Discharge Duct (2.0m) and Return Duct (1.0m).
Voltage of the power source for the indoor fan motor is 380V.
In case of the power source of 415V, the sound pressure level increases by about 2 dB.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.
3. The values with ( )* of sound pressure level, air flow rate, external pressure and motor output indicate the values
in case of external static pressure setting at 110Pa (130Pa for 415V).
4. The external pressure *4) indicates the values when a filter is not used.
5. *5) In case of using R407C or R22, use the accessory reducer and
12.7 piping.
*6) In case of using R407C or R22, use the accessory reducer and
25.4 piping.
*7) In case of using R407C or R22, use the accessory reducer and
28.6 piping.

1-33
 GENERAL DATA

Indoor Unit Type 4-Way Cassette Type

Model RCI-1.0FSN2 RCI-1.5FSN2 RCI-2.0FSN2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 2.9 4.1 5.8
Capacity *1) kcal/h 2,500 3,550 5,000
Btu/h 9,900 14,100 19,800
Nominal Cooling kW 2.8 4.0 5.6
Capacity *2) kcal/h 2,400 3,400 4,800
Btu/h 9,600 13,600 19,100
Nominal Heating kW 3.2 4.8 6.3
Capacity kcal/h 2,800 4,100 5,400
Btu/h 10,900 16,400 21,500
Sound Pressure Level
(Overall A Scale) dB 30-28-27 30-28-27 30-28-27
Outer Dimensions
Height mm 248 248 248
(in.) (9-3/4) (9-3/4) (9-3/4)
Width mm 840 840 840
(in.) (33-1/16) (33-1/16) (33-1/16)
Depth mm 840 840 840
(in.) (33-1/16) (33-1/16) (33-1/16)
Net Weight kg 23 23 24
(lbs.) (51) (51) (53)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 13/12/11 15/13.5/12 16/14/12
(Hi/Me/Lo) (cfm) (459/424/388) (530/477/424) (565/494/424)
Motor W 56 56 56
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
6.35
6.35
6.35
(in.) (1/4) (1/4) (1/4)
Gas Line mm
12.7
12.7
15.88
(in.) (1/2) (1/2) (5/8)
Condensate Drain VP25 VP25 VP25
Approximate
Packing Measurement m3 0.22 0.22 0.22
Adaptable Panel Model P-N23WA P-N23WA P-N23WA
Color Silky White
Outer Dimensions
Height mm 37 37 37
(in.) (1-7/16) (1-7/16) (1-7/16)
Width mm 950 950 950
(in.) (37-3/8) (37-3/8) (37-3/8)
Depth mm 950 950 950
(in.) (37-3/8) (37-3/8) (37-3/8)
Net Weight kg 6 6 6
(lbs.) (13) (13) (13)
Approximate
Packing Measurement m3 0.09 0.09 0.09
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1.5 Meters Beneath the Unit.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.

1-34
 GENERAL DATA

Indoor Unit Type 4-Way Cassette Type

Model RCI-2.5FSN2 RCI-3.0FSN2 RCI-4.0FSN2 RCI-5.0FSN2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 7.3 8.3 11.6 14.5
Capacity *1) kcal/h 6,300 7,100 10,000 12,500
Btu/h 25,000 28,200 39,700 49,600
Nominal Cooling kW 7.1 8.0 11.2 14.0
Capacity *2) kcal/h 6,100 6,900 9,600 12,000
Btu/h 24,200 27,300 38,200 47,800
Nominal Heating kW 8.5 9.0 12.5 16.0
Capacity kcal/h 7,300 7,700 10,700 13,800
Btu/h 29,000 30,700 42,600 54,600
Sound Pressure Level
(Overall A Scale) dB 32-30-28 32-30-28 38-35-33 39-37-35
Outer Dimensions
Height mm 248 298 298 298
(in.) (9-3/4) (11-3/4) (11-3/4) (11-3/4)
Width mm 840 840 840 840
(in.) (33-1/16) (33-1/16) (33-1/16) (33-1/16)
Depth mm 840 840 840 840
(in.) (33-1/16) (33-1/16) (33-1/16) (33-1/16)
Net Weight kg 24 26 29 29
(lbs.) (53) (57) (64) (64)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 20/17/15 21/18/15 32/28/24 34/29/25
(Hi/Me/Lo) (cfm) (706/600/530) (741/635/530) (1,130/989/847) (1,201/1,024/883)
Motor W 56 56 124 124
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
9.53
9.53
9.53
9.53
(in.) (3/8) (3/8) (3/8) (3/8)
Gas Line mm
15.88
15.88
15.88 *3)
15.88 *3)
(in.) (5/8) (5/8) (5/8) (5/8)
Condensate Drain VP25 VP25 VP25 VP25
Approximate
Packing Measurement m3 0.22 0.26 0.26 0.26
Adaptable Panel Model P-N23WA P-N23WA P-N23WA P-N23WA
Color Silky White
Outer Dimensions
Height mm 37 37 37 37
(in.) (1-7/16) (1-7/16) (1-7/16) (1-7/16)
Width mm 950 950 950 950
(in.) (37-3/8) (37-3/8) (37-3/8) (37-3/8)
Depth mm 950 950 950 950
(in.) (37-3/8) (37-3/8) (37-3/8) (37-3/8)
Net Weight kg 6 6 6 6
(lbs.) (13) (13) (13) (13)
Approximate
Packing Measurement m3 0.09 0.09 0.09 0.09
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1.5 Meters Beneath the Unit.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.
3. *3) In case of using R407C or R22, use the accessory adaptor and
19.05 piping.

1-35
 GENERAL DATA

Indoor Unit Type 2-Way Cassette Type

Model RCD-1.0FSN2 RCD-1.5FSN2 RCD-2.0FSN2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 2.9 4.1 5.8
Capacity *1) kcal/h 2,500 3,550 5,000
Btu/h 9,900 14,100 19,800
Nominal Cooling kW 2.8 4.0 5.6
Capacity *2) kcal/h 2,400 3,400 4,800
Btu/h 9,600 13,600 19,100
Nominal Heating kW 3.2 4.8 6.3
Capacity kcal/h 2,800 4,100 5,400
Btu/h 10,900 16,400 21,500
Sound Pressure Level
(Overall A Scale) dB 34-32-30 35-32-30 35-32-30
Outer Dimensions
Height mm 298 298 298
(in.) (11-3/4) (11-3/4) (11-3/4)
Width mm 860 860 860
(in.) (33-7/8) (33-7/8) (33-7/8)
Depth mm 620 620 620
(in.) (24-7/16) (24-7/16) (24-7/16)
Net Weight kg 27 27 27
(lbs.) (60) (60) (60)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 10/9/8 13/11/9 15/13/11
(Hi/Me/Lo) (cfm) (353/318/282) (459/388/318) (530/459/388)
Motor W 35 35 35
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
6.35
6.35
6.35
(in.) (1/4) (1/4) (1/4)
Gas Line mm
12.7
12.7
15.88
(in.) (1/2) (1/2) (5/8)
Condensate Drain VP25 VP25 VP25
Approximate
Packing Measurement m3 0.23 0.23 0.23
Standard Accessories Mounting Bracket
Adaptable Panel Model P-N23DWA P-N23DWA P-N23DWA
Color Silky White
Outer Dimensions
Height mm 30 30 30
(in.) (1-3/16) (1-3/16) (1-3/16)
Width mm 1,100 1,100 1,100
(in.) (43-5/16) (43-5/16) (43-5/16)
Depth mm 710 710 710
(in.) (27-15/16) (27-15/16) (27-15/16)
Net Weight kg 6 6 6
(lbs.) (13) (13) (13)
Approximate
Packing Measurement m3 0.10 0.10 0.10
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1.5 Meters Beneath the Unit.
Voltage of the power source for the indoor fan motor is 220V.
In case of the power source of 240V, the sound pressure level increases by about 1 dB.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.

1-36
 GENERAL DATA

Indoor Unit Type 2-Way Cassette Type

Model RCD-2.5FSN2 RCD-3.0FSN2 RCD-4.0FSN2 RCD-5.0FSN2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 7.3 8.3 11.6 14.5
Capacity *1) kcal/h 6,300 7,100 10,000 12,500
Btu/h 25,000 28,200 39,700 49,600
Nominal Cooling kW 7.1 8.0 11.2 14.0
Capacity *2) kcal/h 6,100 6,900 9,600 12,000
Btu/h 24,200 27,300 38,200 47,800
Nominal Heating kW 8.5 9.0 12.5 16.0
Capacity kcal/h 7,300 7,700 10,700 13,800
Btu/h 29,000 30,700 42,600 54,600
Sound Pressure Level
(Overall A Scale) dB 38-34-31 38-34-31 40-36-33 43-40-36
Outer Dimensions
Height mm 298 298 298 298
(in.) (11-3/4) (11-3/4) (11-3/4) (11-3/4)
Width mm 860 860 1,420 1,420
(in.) (33-7/8) (33-7/8) (55-7/8) (55-7/8)
Depth mm 620 620 620 620
(in.) (24-7/16) (24-7/16) (24-7/16) (24-7/16)
Net Weight kg 30 30 48 48
(lbs.) (66) (66) (106) (106)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 19/16/14 19/16/14 29/24/21 34/29/25
(Hi/Me/Lo) (cfm) (671/565/494) (671/565/494) (1,024/847/742) (1,201/1,024/883)
Motor W 55 55 35 x 2 55 x 2
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
9.53
9.53
9.53
9.53
(in.) (3/8) (3/8) (3/8) (3/8)
Gas Line mm
15.88
15.88
15.88 *3)
15.88 *3)
(in.) (5/8) (5/8) (5/8) (5/8)
Condensate Drain VP25 VP25 VP25 VP25
Approximate
Packing Measurement m3 0.23 0.23 0.37 0.37
Standard Accessories Mounting Bracket
Adaptable Panel Model P-N23DWA P-N23DWA P-N46DWA P-N46DWA
Color Silky White
Outer Dimensions
Height mm 30 30 30 30
(in.) (1-3/16) (1-3/16) (1-3/16) (1-3/16)
Width mm 1,100 1,100 1,660 1,660
(in.) (43-5/16) (43-5/16) (65-3/8) (65-3/8)
Depth mm 710 710 710 710
(in.) (27-15/16) (27-15/16) (27-15/16) (27-15/16)
Net Weight kg 6 6 8 8
(lbs.) (13) (13) (18) (18)
Approximate
Packing Measurement m3 0.10 0.10 0.15 0.15
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1.5 Meters Beneath the Unit.
Voltage of the power source for the indoor fan motor is 220V.
In case of the power source of 240V, the sound pressure level increases by about 1 dB.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.
3. *3) In case of using R407C or R22, use the accessory adaptor and
19.05 piping.

1-37
 GENERAL DATA

Indoor Unit Type Wall Type

Model RPK-1.0FSNSM2 RPK-1.5FSNSM2 RPK-2.0FSNSM2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 2.9 4.1 5.8
Capacity *1) kcal/h 2,500 3,550 5,000
Btu/h 9,900 14,100 19,800
Nominal Cooling kW 2.8 4.0 5.6
Capacity *2) kcal/h 2,400 3,400 4,800
Btu/h 9,600 13,600 19,100
Nominal Heating kW 3.2 4.8 6.3
Capacity kcal/h 2,800 4,100 5,400
Btu/h 10,900 16,400 21,500
Sound Pressure Level
(Overall A Scale) dB 38-36-34 40-38-36 41-39-37
Cabinet Color White
Outer Dimensions
Height mm 280 280 295
(in.) (11) (11) (11-5/8)
Width mm 780 780 1,030
(in.) (30-11/16) (30-11/16) (40-9/16)
Depth mm 210 210 208
(in.) (8-1/4) (8-1/4) (8-3/16)
Net Weight kg 10 10 12
(lbs.) (22) (22) (26)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 10/8/7 11/10/9 14/12/10
(Hi/Me/Lo) (cfm) (353/283/247) (388/353/318) (494/424/353)
Motor kW 0.02 0.02 0.03
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
6.35
6.35
6.35
(in.) (1/4) (1/4) (1/4)
Gas Line mm
12.7
12.7
15.88 or
12.7 (*1)
(in.) (1/2) (1/2) (5/8) or (1/2)
Condensate Drain VP16 VP16 VP16
Approximate
Packing Measurement m3 0.07 0.07 0.11
Standard Accessories Wall Mounting Bracket
(*1) The refrigerant piping size may be required to change depending on the outdoor unit to be connected.
If
12.7 pipe is used at the gas side, remove the flare adaptor at the indoor unit gas piping.
Then attach the flare nut (accessory) for pipe connection.

NOTES:
1. The nominal capacity is the combined capacity of the HITACHI standard SET-FREE system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1 meter beneath the unit and 1 meter from inlet grille.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.

1-38
 GENERAL DATA

Indoor Unit Type Wall Type

Model RPK-2.5FSNSM2 RPK-3.0FSNSM2 RPK-4.0FSNSM2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 7.3 8.3 11.6
Capacity *1) kcal/h 6,300 7,100 10,000
Btu/h 25,000 28,200 39,700
Nominal Cooling kW 7.1 8.0 11.2
Capacity *2) kcal/h 6,100 6,900 9,600
Btu/h 24,200 27,300 38,200
Nominal Heating kW 8.5 9.0 12.5
Capacity kcal/h 7,300 7,700 10,700
Btu/h 29,000 30,700 42,600
Sound Pressure Level
(Overall A Scale) dB 43-40-37 43-40-37 49-46-43
Cabinet Color White
Outer Dimensions
Height mm 333 333 333
(in.) (13-1/8) (13-1/8) (13-1/8)
Width mm 1,150 1,150 1,150
(in.) (45-1/4) (45-1/4) (45-1/4)
Depth mm 245 245 245
(in.) (9-5/8) (9-5/8) (9-5/8)
Net Weight kg 18 18 18
(lbs.) (40) (40) (40)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 17/16/14 17/16/14 22/20/17
(Hi/Me/Lo) (cfm) (600/565/494) (600/565/494) (777/706/600)
Motor kW 0.03 0.03 0.03
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
9.53
9.53
9.53
(in.) (3/8) (3/8) (3/8)
Gas Line mm
15.88
15.88
15.88
(in.) (5/8) (5/8) (5/8)
Condensate Drain VP16 VP16 VP16
Approximate
Packing Measurement m3 0.13 0.13 0.13
Standard Accessories Wall Mounting Bracket
NOTES:
1. The nominal capacity is the combined capacity of the HITACHI standard SET-FREE system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1 meter beneath the unit and 1 meter from inlet grille.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.

1-39
 GENERAL DATA

Indoor Unit Type Floor Type Floor Concealed Type

Model RPF-1.0FSN2E RPF-1.5FSN2E RPFI-1.0FSN2E RPFI-1.5FSN2E
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 2.9 4.1 2.9 4.1
Capacity *1) kcal/h 2,500 3,550 2,500 3,550
Btu/h 9,900 14,100 9,900 14,100
Nominal Cooling kW 2.8 4.0 2.8 4.0
Capacity *2) kcal/h 2,400 3,400 2,400 3,400
Btu/h 9,600 13,600 9,600 13,600
Nominal Heating kW 3.2 4.8 3.2 4.8
Capacity kcal/h 2,800 4,100 2,800 4,100
Btu/h 10,900 16,400 10,900 16,400
Sound Pressure Level
(Overall A Scale) dB 35-32-29 38-35-31 35-32-29 38-35-31
Cabinet Color Spring White - -
Outer Dimensions
Height mm 630 630 620 620
(in.) (24-13/16) (24-13/16) (24-7/16) (24-7/16)
Width mm 1,045 1,170 848 973
(in.) (41-1/8) (46-1/16) (33-3/8) (38-5/16)
Depth mm 220 220 220 220
(in.) (8-11/16) (8-11/16) (8-11/16) (8-11/16)
Net Weight kg 25 28 19 23
(lbs.) (55) (62) (42) (51)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 8.5/7/6 12/10/9 8.5/7/6 12/10/9
(Hi/Me/Lo) (cfm) (300/247/212) (424/353/318) (300/247/212) (424/353/318)
Motor W 20 28 20 28
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
6.35
6.35
6.35
6.35
(in.) (1/4) (1/4) (1/4) (1/4)
Gas Line mm
12.7
12.7
12.7
12.7
(in.) (1/2) (1/2) (1/2) (1/2)
Condensate Drain
18.5 OD
18.5 OD
18.5 OD
18.5 OD
Approximate
Packing Measurement m3 0.22 0.24 0.22 0.23
Standard Accessories -
OD: Outer Diameter
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1 meter from the unit.
1 meter from floor level.
Voltage of the power source for the indoor fan motor is 220V.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.

1-40
 GENERAL DATA

Indoor Unit Type Ceiling Type

Model RPC-2.0FSN2 RPC-2.5FSN2 RPC-3.0FSN2 RPC-4.0FSN2 RPC-5.0FSN2
Indoor Unit Power Supply AC 1
, 220-240V/50Hz, 220V/60Hz
Nominal Cooling kW 5.8 7.3 8.3 11.6 14.5
Capacity *1) kcal/h 5,000 6,300 7,100 10,000 12,500
Btu/h 19,800 25,000 28,200 39,700 49,600
Nominal Cooling kW 5.6 7.1 8.0 11.2 14.0
Capacity *2) kcal/h 4,800 6,100 6,900 9,600 12,000
Btu/h 19,100 24,200 27,300 38,200 47,800
Nominal Heating kW 6.3 8.5 9.0 12.5 16.0
Capacity kcal/h 5,400 7,300 7,700 10,700 13,800
Btu/h 21,500 29,000 30,700 42,600 54,600
Sound Pressure Level
(Overall A Scale) dB 40-37-34 40-37-34 40-37-34 44-41-38 44-41-38
Cabinet Color Silky White
Outer Dimensions
Height mm 210 210 210 270 270
(in.) (8-1/4) (8-1/4) (8-1/4) (10-5/8) (10-5/8)
Width mm 1,100 1,320 1,320 1,320 1,580
(in.) (43-5/16) (51-15/16) (51-15/16) (51-15/16) (62-3/16)
Depth mm 670 670 670 670 670
(in.) (26-3/8) (26-3/8) (26-3/8) (26-3/8) (26-3/8)
Net Weight kg 26 30 30 34 42
(lbs.) (57) (66) (66) (75) (93)
Refrigerant R410A / R407C / R22 (Nitrogen-Charged for Corrosion-Resistance)
Indoor Fan
Air Flow Rate m3/min. 14/12/10 18/15/12 18/15/12 25/21/18 33/28/23
(Hi/Me/Lo) (cfm) (494/424/353) (636/530/424) (636/530/424) (883/742/636) (1,165/989/812)
Motor W 35 50 50 95 135
Connections Flare-Nut Connection (with Flare Nuts)
Refrigerant Piping
Liquid Line mm
6.35
9.53
9.53
9.53
9.53
(in.) (1/4) (3/8) (3/8) (3/8) (3/8)
Gas Line mm
15.88
15.88
15.88
15.88 *3)
15.88 *3)
(in.) (5/8) (5/8) (5/8) (5/8) (5/8)
Condensate Drain VP20 VP20 VP20 VP20 VP20
Approximate
Packing Measurement m3 0.30 0.36 0.36 0.43 0.50
Standard Accessories Mounting Bracket
NOTES:
1. The nominal cooling capacity is the combined capacity of the HITACHI standard split system, and is based on the JIS standard B8616.
Cooling Operation Conditions
Indoor Air Inlet Temperature: 27oC DB (80oF DB)
*1) 19.5oC WB (67oF WB)
*2) 19.0oC WB (66.2oF WB)
Outdoor Air Inlet Temperature: 35oC DB (95oF DB)
Heating Operation Conditions
Indoor Air Inlet Temperature: 20oC DB (68oF DB)
Outdoor Air Inlet Temperature: 7oC DB (45oF DB)
6oC WB (43oF WB)
Piping Length: 7.5 Meters Piping Lift: 0 Meter
2. The sound pressure level is based on following conditions.
1 Meter Beneath the Unit and 1 Meter from Discharge Grille.
Voltage of the power source for the indoor fan motor is 220V.
In case of the power source of 240V, the sound pressure level increases by about 1 dB.
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in the field.
3. *3) In case of using R407C or R22, use the accessory adaptor and
19.05 piping.

1-41
 GENERAL DATA

Unit Type Total Heat Exchanger

Model KPI-2521 KPI-5021 KPI-8021 KPI-10021 *1)
Unit Power Supply AC 1
, 220-240V/50Hz
Air Flow Rate
(Hi/Me/Lo) m3/h 250/250/165 500/500/350 800/800/670 1,000/1,000/870
External Pressure
(Hi/Me/Lo) Pa 65/40/20 150/60/30 140/100/70 160/100/80
Temp. Exchange Efficiency
(Hi/Me/Lo) % 78/78/83 77/77/82 78/78/80.5 79/79/81
Enthalpy Exchange Efficiency
For Heating (Hi/Me/Lo) % 69/69/74 67/67/73 71/71/73 70/70/73
For Cooling (Hi/Me/Lo) % 62.5/62.5/68 61.5/61.5/68 64.5/64.5/68 64.5/64.5/67
Sound Pressure Level (Over A Scale)
at 1.5m from the unit (under) 26.5-27.5/25-26 32.5-33.5/30-31 33.5-34.5/32-33 36-37/34-35
(Hi/Me/Lo) *2), *4) dB /21-22 /23.5-24.5 /30-31 /31.5-32.5
at Air Outlet 33.5-34.5/32-33 40.5-41.5/38-39 44.5-45.5/43-44 47-48/45-46
(Hi/Me/Lo) *3), *4) dB /26-27 /29.5-30.5 /40-41 /41.5-42.5
Outer Dimensions
Height mm 275 317 398 398
(in.) (10-13/16) (12-1/2) (15-11/16) (15-11/16)
Width mm 735 1,016 1,004 1,231
(in.) (28-15/16) (40) (39-1/2) (48-7/16)
Depth mm 780 888 1,164 1,164
(in.) (30-11/16) (34-15/16) (45-13/16) (45-13/16)
Net Weight kg 21 33 61 72
(lbs.) (46) (73) (134) (159)
Connection Duct Diameter mm
150
200
250
250

Unit Type In-the-Ceiling Type

Model KPI-2521 KPI-5021 KPI-8021 KPI-10021 *1)
Unit Power Supply AC 1
, 220/60Hz
Air Flow Rate
(Hi/Me/Lo) m3/h 250/250/150 500/500/300 800/800/660 1,000/1,000/720
External Pressure
(Hi/Me/Lo) Pa 100/50/20 200/60/20 230/120/80 200/110/60
Temp. Exchange Efficiency
(Hi/Me/Lo) % 78/78/84 77/77/83.5 78/78/81 79/79/83
Enthalpy Exchange Efficiency
For Heating (Hi/Me/Lo) % 69/69/75 67/67/75 71/71/73.5 70/70/76
For Cooling (Hi/Me/Lo) % 62.5/62.5/70 61.5/61.5/70 64.5/64.5/68.5 64.5/64.5/71
Sound Pressure Level (Over A Scale)
at 1.5m from the unit (under)
(Hi/Me/Lo) *2), *4) dB 28.5/25.5/21 32.5/28.5/23 35/31/29 36/34/30
at Air Outlet
(Hi/Me/Lo) *3), *4) dB 35.5/32.5/26 40.5/36.5/29 46/42/39 47/45/40
Outer Dimensions
Height mm 275 317 398 398
(in.) (10-13/16) (12-1/2) (15-11/16) (15-11/16)
Width mm 735 1,016 1,004 1,231
(in.) (28-15/16) (40) (39-1/2) (48-7/16)
Depth mm 780 888 1,164 1,164
(in.) (30-11/16) (34-15/16) (45-13/16) (45-13/16)
Net Weight kg 21 33 61 72
(lbs.) (46) (73) (134) (159)
Connection Duct Diameter mm
150
200
250
250
NOTES:
*1): KPI-10021 has different units according to the applied power supply, 220-240V/50Hz and 220V/60Hz.
*2): The sound pressure level is based on following conditions.
1.5 meters beneath the unit and this data was measured in an anechoic chamber so that reflected sound should be taken
into consideration in the field.
*3): The noise at the air outlets is the values at a 45o angle, 1.5 meters in front of the unit.
*4): The sound pressure level is based on the total heat exchange mode.
In case of the bypass ventilation mode, the sound pressure level increase by approximately 1 dB(A).

1-42
 DIMENSIONAL DATA

3. Dimensional Data
3.1 Dimensional Data for Indoor Units

In-the-Ceiling Type
Models: RPI-0.8FSN2, RPI-1.0FSN2, RPI-1.5FSN2, RPI-2.0FSN2, RPI-2.5FSN2, RPI-3.0FSN2,
RPI-4.0FSN2 and RPI-5.0FSN2

Unit: mm

l -
6
b (Around the Flange)
40 a
e c x 300 = d
300 4 - 40 x 12
20

(for Suspension Bolt)

Air Inlet
30
22

x
m

22
n

Remote Control Switch g

33.5

Viewed from A
22
30

120
20

300 l -
6
e c x 300 = d (Around the Flange) Drain Pipe Connection Drain Pipe Connection
(2.0 to 5.0HP Standard Position) (VP25) (0.8 to 1.5HP with Drain-Up
Mechanism)
Refrigerant Gas Pipe Connection
(With
i Flare Nut)
Air Outlet
Refrigerant Liquid Pipe Connection

2xv=w
a 75 (Electrical Control Box) (With
h Flare Nut) u 45
2x90=180
220

A
q

90

v
r
97
p

23

35
s
t

48.5 f j (Refrigerant Gas Pipe Connection) 246 (Refrigerant Liquid Pipe Connection)
90 (Drain Pipe Connection) 321 (Refrigerant Gas Pipe Connection)
k (Refrigerant Liquid Pipe Connection) 377 (Drain Pipe Connection: 2.0 to 5.0HP)
402 (Drain Pipe Connection: 0.8 to 1.5HP)

Dimension a b c d e f g h i j k
HP
0.8 650 730 1 300 215 553 583 6.35 12.7 70 92
1.0 650 730 1 300 215 553 583 6.35 12.7 70 92
1.5 650 730 1 300 215 553 583 6.35 12.7 70 92
2.0 900 980 2 600 190 803 833 6.35 15.88 77 92
2.5 900 980 2 600 190 803 833 9.53 15.88 77 95
3.0 650 730 1 300 215 553 583 9.53 15.88 77 95
4.0 900 980 2 600 190 803 833 9.53 15.88 (19.05)*1 81 95
5.0 1300 1380 3 900 240 1203 1233 9.53 15.88 (19.05)*1 81 95
*1: In case of using R407C or R22, use
19.05

Dimension l m n p q r s t u v w x
HP
0.8 10 676 720 23 270 182 222 43 220 100 200 226
1.0 10 676 720 23 270 182 222 43 220 100 200 226
1.5 10 676 720 23 270 182 222 43 220 100 200 226
2.0 12 676 720 23 270 182 222 43 220 100 200 226
2.5 12 676 720 23 270 182 222 43 220 100 200 226
3.0 10 756 800 103 350 204 244 123 300 140 280 306
4.0 12 756 800 103 350 204 244 123 300 140 280 306
5.0 14 756 800 103 350 204 244 123 300 140 280 306

1-43
 DIMENSIONAL DATA

In-the-Ceiling Type
Models: RPI-8FSN and RPI-10FSN

Unit: mm

22 -
3 4 - M10 Holes 21 -
3 Air Discharge Side

(for Suspension Bolts) 3

1100 (Duct Size <outer size>)

1100 (Duct Size <outer size>)

1326 (for Suspension Bolts)

50 x 21 = 1050

50 x 20 = 1000
1250 (Unit)

1372
Air Intake Side

50
25

2, 3 10 15

(170)
102

100

23

78
420 1034 (for Suspension Bolts) 60 340
(Duct Size <outer size>) (Duct Size <outer size>)
1124

Remote Control Switch 1120

PC-AR (Optional)
24 1067 29 Refrigerant Liquid Pipe Connection
(
b: Brazing)
10 Drain Pipe Connection 15
(for using Drain-up Mechanism)
Refrigerant Gas Pipe Connection
(
a: Brazing)
Electrical Control Box
120 50x6=300
50 x 7 = 350

340
44
420

470
327

20
20

35

30

164

105
41

Cutout for Power Source Cable 95 249

Cutout for Remote Control Switch Cable 422

Drain Pipe Connection (VP-25) 489

(Standard Drain Piping Position)

Min. 20

Switch Box
JISC8336-1985
(Field-Supplied)

20 20
Min. 20

Wall Mounting Embedding Cable Service Access Panel Ceiling

in the Wall
* Prepare the Service Access Panel for service.
Mounting for Remote Control Switch PC-AR (Optional) * In case that the ceiling board is not be detachable
for servicing, prepare a service access panel below
the indoor unit for removing the indoor unit.

Service Space
1 : Secure the service space of false ceiling
for cleaning the heat exchanger.
2 : Use the air filter (field-supplied) at the intake side.
And secure the service space for the air filter.
730
3 : Use the canvas duct between the indoor unit and duct
for duct connection in order to eliminate vibration.
800 (at intake and discharge sides)
0
~20
200 150
~30 Dim.
0
0 a b
50 135 HP Ref.
450 50 1
R410A 19.05 9.53
8.0
450
R22, R407C (*) 25.4 12.7
R410A 22.2 9.53
Service Access Panel 10.0
R22, R407C (*) 28.6 12.7
(*): In case of using R22 or R407C, use the accessory adaptor.

1-44
 DIMENSIONAL DATA

4-Way Cassette Type

Models: RCI-1.0FSN2, RCI-1.5FSN2, RCI-2.0FSN2 and RCI-2.5FSN2 with Air Panel P-N23WA (Optional)

Unit: mm

Mark Name Remark

20 860~910 20 1 Air Outlet 4-Way
(Opening Hole for Ceiling)
840 4-14 x 26 Holes 2 Air Inlet
760 (for Suspension Bolt) 3 Refrigerant Gas Pipe Connection with
a Flare Nut
(for Suspension Bolt) 4 Refrigerant Liquid Pipe Connection with
b Flare Nut
14

20
5 Drain Pipe Connection VP25
6 Wiring Hole for Conduit Tube
32.5 Knockout Hole
7 Wiring Hole 30 x 39 Hole

(Opening Hole for Ceiling)

8 Suspension Bracket

(for Suspension Bolt)

9 Suspension Bolt 4-M10 or W3/8
10 Supply Duct Connection 150 x 385 Knockout Hole

860~910
760 11 Supply Duct Connection 150 x 400 Knockout Hole

840
25 (Liquid Pipe)
24 (Drain Pipe)

12 Remote Control Switch (PC-AR) without Cable

18 (Gas Pipe)

13 Shielded Twist-Pair Cable for PC-AR Min. 0.75mm2, Field-Supplied

Dimension a b
HP
1.0 12.7 6.35
B 1.5 12.7 6.35
20

110 (Gas Pipe)

180 (Liquid Pipe)
2.0 15.88 6.35
8 9 2.5 15.88 9.53 D
710 (Drain Pipe) Suspension Bolts M10 or W3/8
(Field-Supplied)

Duct Adapter Connection

3 4 5 Viewed from C
E E

C
248
36
31
127 (Liquid Pipe)

102
118 (Drain Pipe)
37
102 (Gas Pipe)

A
Air Inlet Grille
7 6 Optional Air Panel

Optional 12 13 (Field-Supplied) 10
In case of using this,
cut the insulation material 385 30
along to the line indicated 220 100

46
opening position.
2 1
120 7 6 In case of using this,
cut the insulation material
145

150
along to the line indicated
opening position.
5

25
10

25
9-M4 75 135 135 75
127 85
31

(for Self-Tapping Screw)

Viewed from B Enlarged View of D
950

In case of using this, 11

400 50
Switch Box cut the insulation material
JISC8336-1985 220 100
46

along to the line indicated

(Field-Supplied) opening position.
145

150

950
25
10

20 20 10
Viewed from A
Wall Mounting Embedding Cable 9-M4 75 135 135 75
in the Wall (for Self-Tapping Screw)
Mounting for Remote Control Switch (Optional) Enlarged View of E
Min.

Min.

Min.
100

100

100

Service Space

Min. Min. Min. Min. Min.

500 500 Surroundings 500 3000 500
in the Ceiling
NOTE:
Distance between the wall and panel edge must be
a min. 1500mm to prevent short circuiting.
Min.

Min.

Min.

Service Access Panel

100

100

100

Piping Connection Piping Connection Service Access Piping Connection

Service Access Panel Panel

Separated Installation Closed Installation

1-45
 DIMENSIONAL DATA

4-Way Cassette Type

Models: RCI-3.0FSN2, RCI-4.0FSN2 and RCI-5.0FSN2 with Air Panel P-N23WA (Optional)
Unit: mm
20 860~910 20 Mark Name Remark
(Opening Hole for Ceiling) 1 Air Outlet 4-Way
840 4-14 x 26 Holes
(for Suspension Bolt)
2 Air Inlet
760
(for Suspension Bolt)
3 Refrigerant Gas Pipe Connection with
a Flare Nut
14 4 Refrigerant Liquid Pipe Connection with
b Flare Nut

20
5 Drain Pipe Connection VP25
6 Wiring Hole for Conduit Tube
32.5 Knockout Hole
7 Wiring Hole 30 x 39 Hole

(Opening Hole for Ceiling)

8 Suspension Bracket

(for Suspension Bolt)

9 Suspension Bolt 4-M10 or W3/8

860~910
10 Supply Duct Connection 150 x 385 Knockout Hole

760

840
11 Supply Duct Connection 150 x 400 Knockout Hole
25 (Liquid Pipe)
24 (Drain Pipe)
18 (Gas Pipe)

12 Remote Control Switch (PC-AR) without Cable

13 Shielded Twist-Pair Cable for PC-AR Min. 0.75mm2, Field-Supplied

Dimension a b
HP
3.0 15.88 9.53
B
20

110 (Gas Pipe) 4.0 15.88 (19.05)*1 9.53

180 (Liquid Pipe) 5.0 15.88 (19.05)*1 9.53
8 9 Suspension Bolts M10 or W3/8
710 (Drain Pipe)
(Field-Supplied)
*1: In case of using R407C or R22, use
19.05.
D

Duct Adapter Connection

3 4 5 Viewed from C
E E

C
298
127 (Liquid Pipe)

36
31

102
118 (Drain Pipe)
102 (Gas Pipe)

37

A
Air Inlet Grille
7 6 Optional Air Panel

Optional 12 13 (Field-Supplied) 10
In case of using this, 385 30
cut the insulation material 220 100

96
along to the line indicated
opening position.
2 1
120 7 6 In case of using this,
cut the insulation material
145

150
along to the line indicated
opening position.
5

25
10

25
9-M4 75 135 135 75
127 85
31

(for Self-Tapping Screw)

Viewed from B Enlarged View of D
950

400 50
Switch Box In case of using this, 11
JISC8336-1985 220 100
96

cut the insulation material

(Field-Supplied)
along to the line indicated
opening position.
145

150

950
20 20
Viewed from A
25
10

Embedding Cable 10
Wall Mounting
in the Wall 9-M4 75 135 135 75
Mounting for Remote Control Switch (Optional) (for Self-Tapping Screw)
Enlarged View of E

Service Space
Min.

Min.

Min.
100

100

100

Min. Min. Min. Min. Min.

500 500 Surroundings 500 3000 500
in the Ceiling
NOTE:
Distance between the wall and panel edge must be
a min. 1500mm to prevent short circuiting.
Min.

Min.

Min.

Service Access Panel

100

100

100

Piping Connection Piping Connection Service Access Piping Connection

Service Access Panel Panel

Separated Installation Closed Installation

1-46
 DIMENSIONAL DATA

2-Way Cassette Type

Models: RCD-1.0FSN2, RCD-1.5FSN2, RCD-2.0FSN2, RCD-2.5FSN2 and RCD-3.0FSN2
with Air Panel P-N23DWA (Optional)
Unit: mm

Mark Name Remark

20 1060 (Opening Hole for Ceiling) 20
1 Air Outlet
890 (for Suspension Bolt)
4-12x32 Hole 2 Air Inlet
860 (for Suspension Bolt)
3 Refrigerant Gas Pipe Connection with
a Flare Nut
12
4 Refrigerant Liquid Pipe Connection with
b Flare Nut

20
5 Drain Pipe Connection VP25

(Opening Hole for Ceiling)

6 Wiring Hole for Conduit Tube
32.5

(for Suspension Bolt)

7 Wiring Hole 30 x 39 Hole
540 8 Suspension Bracket

620
670
8 9 Suspension Bolt 4-M10 or W3/8
10 Electrical Control Box
11 Supply Duct Connection 2-150 x 400
12 Remote Control Switch (PC-AR) Optional
Min. 0.75mm2, Field-Supplied
20

13 Shielded Twist-Pair Cable for PC-AR

95 (Gas Pipe) 410 Dimension

5 4 3 9 a b
95 (Liquid Pipe) 285 HP
25 (Drain Pipe) 205 1.0 12.7 6.35
D 1.5 12.7 6.35
2.0 15.88 6.35
115

50
298

2.5 15.88 9.53

260

B E
125

3.0 15.88 9.53

30

445 11 In case of using 11 ,

A Cut out the insulation
material along this line.
9-M4
(for Self-Tapping Screw)
12 13 (Field-Supplied) 170 400
Optional
150 140
70

55
1 120 10
150

180

15
15
30

7 6 Cut out the insulation 135 135 80

710

material along this line. 430

90
Enlarged View of D
2
11 In case of using 11 ,
Cut out the insulation
1 9-M4 material along this line.
1100 (for Self-Tapping Screw)
50

400 170
Viewed from A Viewed from B
120 120 120 35
55

70
180

150

Service Access Panel

Piping Connection
15
15
110

Surroundings
in the ceiling 30 185 185
MIN.
500

Service Access Panel 430

Piping Connection Viewed from E

MIN. MIN.
100 500
3000
MIN.
MIN.
500

Switch Box
JISC8336-1985
(Field-Supplied)

MIN. MIN. MIN. MIN. 20 20

MIN.

MIN.

100 500 100 500

500

500

Wall Mounting Embedding Cable

in the Wall

Separated Installation Closed Installation Mounting for Remote Control Switch (Optional)

Service Space NOTE:

1. Distance between the wall and panel edge must
be a min. 1500mm to prevent short circuiting.

1-47
 DIMENSIONAL DATA

2-Way Cassette Type

Models: RCD-4.0FSN2 and RCD-5.0FSN2 with Air Panel P-N46DWA (Optional)

Unit: mm

Mark Name Remark

20 1620 (Opening Hole for Ceiling) 20
1 Air Outlet
1450 (for Suspension Bolt) 2 Air Inlet
4-12 x 32 Hole
1420 (for Suspension Bolt) 3 Refrigerant Gas Pipe Connection with
15.88 (
19.05)*1 Flare Nut
12 4 Refrigerant Liquid Pipe Connection with
9.53 Flare Nut

20
5 Drain Pipe Connection VP25
6 Wiring Hole for Conduit Tube
32.5
7 Wiring Hole 30 x 39 Hole
8 Suspension Bracket
9 Suspension Bolt 4-M10 or W3/8

540

620

670
10 Electrical Control Box
11 Supply Duct Connection 2-150 x 610
12 Remote Control Switch (PC-AR) Optional
13 Shielded Twist-Pair Cable for PC-AR Min. 0.75mm2, Field-Supplied
*1: In case of using R407C or R22, use
19.05.

20
8
95 (Gas Pipe) 410
95 (Liquid Pipe)
5 4 285
3
25 (Drain Pipe) 205
9

D
298
260

B E
125
115

50
30

445

A
10-M4
Optional 12 13 (Field-Supplied) (for Self-Tapping Screw)
170 610
140 180 160
70

55
10
1 120

180
150

30
15

15
180 180 140
11 In case of using 11 ,
710

Cut out the insulation

640
material along this line.
2 Enlarged View of D

1660 In case of using 11 , 11

Cut out the insulation 610 170
1
Viewed from A material along this line.
160 160 160 80
55

70

Service Access Panel

180

Piping Connection
150

Surroundings
15
MIN.

110

in the ceiling
500

30 190 200 190

10-M4
Service Access Panel 640
(for Self-Tapping Screw)
Piping Connection Viewed from E

MIN. MIN.
3000
MIN.

100 500
MIN.
500

Cut out the insulation 6

Switch Box
material along this line.
JISC8336-1985
7 (Field-Supplied)

90 20 20
MIN. MIN. MIN.
MIN.

MIN.
MIN.
500

500

100 500 100 500

Wall Mounting Embedding Cable
in the Wall
50

Separated Installation Closed Installation Mounting for Remote Control Switch (Optional)
Viewed from B

Service Space
NOTE:
1. Distance between the wall and panel edge must
be a min. 1500mm to prevent short circuiting.

1-48
 DIMENSIONAL DATA

Wall Type
Models: RPK-1.0FSNSM2 and RPK-1.5FSNSM2

Unit: mm

Mark Name Remark

1 Air Outlet
2 Air Inlet
3 Refrigerant Gas Pipe Connection with
12.7 Flare Nut
4 Refrigerant Liquid Pipe Connection with
6.35 Flare Nut
Piping 5 Drain Pipe Connection VP16
6 Wiring and Piping Hole Knockout Hole
Piping Piping 7 Wiring and Piping Hole
65 Knockout Hole
8 Wiring and Piping Hole
65 Knockout Hole
9 Suspension Bracket
Remote Control Switch Wired PC-AR
10
(Option) Wireless PC-LH3A
2 2
780 210
6 6
280
60

60
5

5
47 Auto Louver 47
Receiver Part
1 10 Option

125
540 120 56
(PC-AR) (PC-LH3A)

410
480 108
5 4 3

Viewed from A

Flange Part for Inserting

190 400 190 Suspension Bracket
37.5 15
7.5 8 23 30 30 20 20 20 8 Outline of the Unit
5 34 20 20 20 15 30 30 23 42 37
44
7.5

28
15 35 27 24 20

20 50 20 20 20 20 20 20
20 25 25 25 30 25 25 25
280

20
45

45
20
20x3=6

60 5 38 38 5 115
20 20
65 530 10
780
Min. 150

8 9 7

Switch Box
JISC8336-1985
(Field-Supplied)

20 20
Min. 1000

Wall Mounting Embedding Cable Min. 100 Min. 100

in the Wall

Unit: mm
Mounting for Remote Control Switch (Option)
(In case of using PC-AR)
Service Space

1-49
 DIMENSIONAL DATA

Wall Type
Model: RPK-2.0FSNSM2

Unit: mm

Mark Name Remark

1 Air Outlet
2 Air Inlet
3 Refrigerant Gas Pipe Connection with
15.88 or
12.7 Flare Nut (*1)
4 Refrigerant Liquid Pipe Connection with
6.35 Flare Nut
5 Drain Pipe Connection VP16
6 Wiring and Piping Hole Knockout Hole
1019 Piping
7 Wiring and Piping Hole
65 Knockout Hole
8 Wiring and Piping Hole
65 Knockout Hole
9 Suspension Bracket
Piping Piping
Remote Control Switch Wired PC-AR
10
(Option) Wireless PC-LH3A
(*1): The refrigerant piping size may be required to change depending
on the outdoor unit to be connected. If
12.7 pipe is used at
the gas side, remove the flare adaptor at the indoor unit gas piping.
2 2 Then attach the flare nut (accessory) for pipe connection.
1030 208

6 6
295

60
60

5
5

47 47
1 Auto Louver
Indication Part Receiver Part 10 Option

A
4 3 125

Gas Pipe Connection

(
12.7)
120 56
Flare Adaptor
(PC-AR) (PC-LH3A)

P a
Pipe Diameter a
5

15.88 440 470

12.7 410
Gas Pipe Connection
550 150
(
15.88)

Viewed from A Enlarged View P

Flange Part for Inserting
Outline of the Unit Suspension Bracket
314 450 266
13.1 21.9 38.1 20 38.1 24.9 13.1
25 25 50 50 40 40 50 50 22
9.5
20x5=100
20

20 20 20 20
295

48.5
20 30 30 40 40 30 30 20 12 8.5 150
45 49

80

45
15
15x4=60

21.9 55 6.5 12.5

200 15 20 48.5 7
8.5
8.5 4 20
8 9
Min. 150

1030

Switch Box
JISC8336-1985
(Field-Supplied)

20 20 Min. 100 Min. 100

Min. 1000

Wall Mounting Embedding Cable

in the Wall Unit: mm

Mounting for Remote Control Switch (Option)

(In case of using PC-AR)
Service Space

1-50
 DIMENSIONAL DATA

Wall Type
Models: RPK-2.5FSNSM2, RPK-3.0FSNSM2 and RPK-4.0FSNSM2
Unit: mm
Mark Name Remark
1 Air Outlet
2 Air Inlet
1140 3 Refrigerant Gas Pipe Connection with
15.88 Flare Nut
4 Refrigerant Liquid Pipe Connection with
9.53 Flare Nut
Piping
5 Drain Pipe Connection VP16
6 Wiring and Piping Hole Knockout Hole
Piping Piping 7 Wiring and Piping Hole
80 Knockout Hole
8 Wiring and Piping Hole
80 Knockout Hole
9 Suspension Bracket
Remote Control Switch Wired PC-AR
10
(Option) Wireless PC-LH3A
2
2
1150
245

6 6
333
70

70
8

8
60 Auto Louver 60
1
Indication Part Receiver Part
10 Option
A
4 5

125
120 56
(PC-AR) (PC-LH3A)

550
3
572

654 141

Viewed from A

565 433.6
780
660
560
105 100 250 100 105 87
20x5 28 50x4 50x4
20

25
40 20

20

229

20
221
333

141
20

10
60
93
42

42

7
300 300
58 141
8 Outline of the Unit
9
1150
Flange Part for
Min. 100

Inserting Suspension Bracket

Switch Box
JISC8336-1985
(Field-Supplied)

20 20
Min. 100 Min. 200
Min. 1000

Wall Mounting Embedding Cable

in the Wall
Unit: mm
Mounting for Remote Control Switch (Option)
(In case of using PC-AR)
Service Space
1-51

1-51
 DIMENSIONAL DATA

Floor Type
Models: RPF-1.0FSN2E and RPF-1.5FSN2E
Unit: mm

30
168

157
40

163 220
156

52
133
182
630

529
388
260
134

View from Upper Side View from Front Side

60

103

315

630
85

220
220

b c

140
b c For Bolt d 228
a 2-12, 15x18 a a
Location of Fixing Holes on Location of Fixing Holes
Location of Fixing Holes on Wall
Floor for Wood Screws (4-M5) on Floor for Bolts (2-M8)
Ceiling

1000
Min.
630

Min. Min.
Wall 300 a 300 Wall

Service Access

Mark Name Remark

1 Air Intlet
2 Air Outlet
3 Refrigerant Gas Line Piping Connection with Flare Nut
12.7
4 Refrigerant Liquid Line Piping Connection with Flare Nut
6.35
5 Condensate Drain Hose
18.5 Outer Diameter
6 Drain Pan
7 Fixing Hole on Wall 4-
14 (Rear)
8 Adjusting Screw For Installation
9 Fixing Hole on Floor 4-
7 for Wood Screw
10 Fixing Hole on Floor
11 Opening for Wiring Rear Side
12 Space for Piping Connection on Floor

Dimension a b c d
HP
1.0 1045 754 217 732
1.5 1170 879 217 857

1-52
 DIMENSIONAL DATA

Floor Concealed Type

Models: RPFI-1.0FSN2E and RPFI-1.5FSN2E

Unit: mm

220
220
122 50
72
13 64 133

19
52
620
315

529
388
52

260
134
114

100

25 55
36 b 85 60
a 103

View from Upper Side View from Front Side

60

103

315

620
85

220
220

138
b c b c d 77
a a a

Location of Fixing Holes on

Floor for Wood Screws (4-M5)
1000
Min.

620
640

Min. Min. Min. Min.

240 a 240 240 a 240

Mark Name Remark

1 Air Intlet
2 Air Outlet
3 Refrigerant Gas Line Piping Connection with Flare Nut
12.7
4 Refrigerant Liquid Line Piping Connection with Flare Nut
6.35
5 Condensate Drain Hose
18.5 Outer Diameter
6 Drain Pan
7 Fixing Hole on Wall 4-
14 (Rear)
8 Adjusting Screw For Installation
9 Fixing Hole on Floor 4-
7 for Wood Screw

Dimension a b c d
HP
1.0 863 754 66 732
1.5 988 879 66 857

1-53
 DIMENSIONAL DATA

Ceiling Type
Models: RPC-2.0FSN2, RPC-2.5FSN2 and RPC-3.0FSN2
Unit: mm
370
9 3 Cut out the resin along this line.
110 92

27
70
12 (Field-Supplied)

110
148
11 Optional

280
670
120

4-12
(Hole for Suspension Bolt)

(50) b (50) 10
a

Max.50
Suspension Bolt Length 4 8
1 38
Suspension Bracket

52
216
210

160
12

12
70 c 70 118 74
Left Side

Switch Box
JISC8336-1985
176

(Field-Supplied)

20 20

Wall Mounting Embedding Cable

305

in the Wall

Mounting for Remote Control Switch (Optional)

2
205 Refrigerant Gas Piping 156
with 15.88 Flare Nut
5 Cut out the resin along this line. 7
d Refrigerant Liquid Piping 106
with 
e Flare Nut
67

40
130
104
40

135 175 102

370

Piping Position 6 9

Mark Name Remark

1 Air Outlet
2 Air Inlet
3 Hole for Refrigerant Piping Hole for Upper Side Arrangement
MIN. MIN.8 Knockout Hole
MIN.

MIN.40
500

300
MIN.400 4 Hole for Refrigerant Piping
for Right Side Arrangement
Separated Installation 5 Hole for Refrigerant Piping Hole for Rear Side Arrangement
VP20
6 Drain Piping Connection
(for Rear Right Side Arrangement)
VP20
7 Hole for Drain Piping
(for Rear Left Side Arrangement)
MIN. MIN. Knockout Hole
MIN.40 300 300 8 Hole for Drain Piping
for Left Side Arrangement
Closed Installation 9 Wiring Hole for Conduit Tube
26.5 Hole
10 Suspension Bracket
Service Space
11 Remote Control Switch (PC-AR) Optional
12 Shielded Twist-Pair Cable for PC-AR Min. 0.75mm2, Field-Supplied

Dimension a b c d e
HP
2.0 1100 1000 960 200 6.35
2.5 1320 1220 1180 195 9.53
3.0 1320 1220 1180 195 9.53

1-54
 DIMENSIONAL DATA

Ceiling Type
Models: RPC-4.0FSN2 and RPC-5.0FSN2
Unit: mm
280
9 3 Cut out the resin
110 92
along this line.

27
70
12 (Field-Supplied)

110
147
11 Optional

280

670
120

4-
12
(Hole for Suspension Bolt)

(50) b (50)
a 10

1 4 8
38 Max.50
Suspension Bracket Suspension Bolt Length
276
270

52
160

12
12
70 c 70 118 74
Left Side

Switch Box
JISC8336-1985
176

(Field-Supplied)

20 20

Wall Mounting Embedding Cable

305

in the Wall

Mounting for Remote Control Switch (Optional)

2 210 Refrigerant Gas Piping with
15.88 (*1) Flare Nut 156

5 Cut out the resin along this line. 7

195 Refrigerant Liquid Piping with
9.53 Flare Nut 106

*1: In case of using R407C or R22, use
19.05.

67

40
130
104

135 175 103

280
6 9
Piping Position

Mark Name Remark

1 Air Outlet
2 Air Inlet
MIN.

MIN.
3 Hole for Refrigerant Piping Hole for Upper Side Arrangem
500

MIN.40 300 MIN.8

Knockout Hole
Separated Installation MIN. 4 Hole for Refrigerant Piping
400 for Right Side Arrangement
5 Hole for Refrigerant Piping Hole for Rear Side Arrangem
VP20
6 Drain Piping Connection
(for Rear Right Side Arrangem
MIN. MIN. VP20
MIN.40 300 300 7 Hole for Drain Piping
(for Rear Left Side Arrangem
Closed Installation Knockout Hole
8 Hole for Drain Piping
for Left Side Arrangement
Service Space
9 Wiring Hole for Conduit Tube
26.5 Hole
10 Suspension Bracket
11 Remote Control Switch (PC-AR) Optional
12 Shielded Twist-Pair Cable for PC-AR Min. 0.75mm2, Field-Supplied

Dimension a b c
HP
4.0 1320 1220 1180
5.0 1580 1480 1440

1-55
 DIMENSIONAL DATA

3.2 Dimensional Data for Total Heat Exchangers

Total Heat Exchangers

Models: KPI-2521, KPI-5021, KPI-8021 and KPI-10021

Unit: mm

EA and OA ducts are applicable from this side.

K
Damper plate
E
Air Exhaust Fan

EA RA
(Exhaust Air) (Return Air)
(Standard Position)

D
A

Power Cord Opening

OA SA

115
(Outside Air) (Supply Air)
(Standard Position)
10
22
Min.600

K
150 to 250

C
Air Supply Fan
Service Access
Panel Position
Electrical Control Box

Service Cover

Heat Exchanging Element

G B G

K
Suspension Bracket
H

Air Filters

Model KPI-2521 KPI-5021 KPI-8021 KPI-10021

A 735 1,016 1,004 1,231
Outer
Dimension B 780 888 1,164 1,164
C 275 317 398 398
For D 765 1,048 1,036 1,263
Suspension Bolt E 700 790 1,030 1,030
Duct F 530 745 690 920
G 63 79 79 79
Duct H 142 192 242 242
Diameter J 160 208 258 258
Duct
(direction change) K 102 124 149 149

1-56
 SELECTION DATA

4. Selection Data
4.1 Operation Space

In-the-Ceiling Type
Models: RPI-0.8FSN2, RPI-1.0FSN2, RPI-1.5FSN2, RPI-2.0FSN2, RPI-2.5FSN2, RPI-3.0FSN2,
RPI-4.0FSN2 and RPI-5.0FSN2
Electrical Box Service Access
Door (Min. 450)
Service Space
100 Rear Side of False Ceiling 600
In case that the

1000
ceiling board can

Min.
not be detected

400
Rear Side
for servicing,
prepare a service
access door
below the indoor
275

unit for removing

the indoor unit.
Front Side
Front Side (130)
35

1000
Min.
View from Bottom Min.
Min. 600
600
View from Top

Models: RPI-8FSN and RPI-10FSN

Service Space

Min. 20
730

800
0
~20
200 150
~30
0
0
135

Min. 20
450 50
50
Service Access Panel Ceiling
Secure the service space
450 of false ceiling for cleaning
the heat exchanger. * Prepare the Service Access Panel for service.
Service Access Panel * In case that the ceiling board is not be detachable
for servicing, prepare a service access panel below
the indoor unit for removing the indoor unit.

4-Way Cassette Type

Models: RCI-1.0FSN2, RCI-1.5FSN2, RCI-2.0FSN2, RCI-2.5FSN2, RCI-3.0FSN2,
RCI-4.0FSN2 and RCI-5.0FSN2

Unit: mm
1500

1500
1500

Min.

Min.
Min.

Min. 500 Min. 100

Min. Min. Min. Min. Min. Piping

1500 1500 1500 3000 1500 Connection
Side
1500

1500
1500

Min.

Min.
Min.

Min. 100 Min. 500

Min. 1000
Piping Connection Piping Connection Piping Connection Service Space
Service Access Door Service Access Door Service Access Door
Separated Installation Closed Installation
Distance from Wall Side

1-57
 SELECTION DATA

2-Way Cassette Type

Models: RCD-1.0FSN2, RCD-1.5FSN2, RCD-2.0FSN2, RCD-2.5FSN2, RCD-3.0FSN2,
RCD-4.0FSN2 and RCD-5.0FSN2

Service
Min. 1500 Access Min. 1500 10 to 20mm
Service
Panel Access 298mm
Min. Panel Unit Height
Min.
1500 in False Celling
1500
Min.
1500 Unit Height in False Celling
Min.
1500
Min. 1500
Min. 3000
Service Min. 100
Access Min. 500
Piping Connection Side Min. Panel
Separated Installation 1500
Piping
Min. Connection
1500 Side
Min. 1500 Min. 500
Min. 500
Min. 1000
Piping Connection Side
Closed Installation of Two Units Service Space
Distance from Wall Side

Wall Type
Models: RPK-1.0FSNSM2 and RPK-1.5FSNSM2 Model: RPK-2.0FSNSM2

Unit: mm

Min.
150
Min.

150
Unit: mm

Min.
Min.
1000

100

1000
Min.

Min.
Min.
100 Min.
100 100

Models: RPK-2.5FSNSM2, RPK-3.0FSNSM2 and RPK-4.0FSNSM2

Min.

Unit: mm
100
1000

Min.
Min.

Min.
100 200

1-58
 SELECTION DATA

Floor Type
Models: RPF-1.0FSN2E and RPF-1.5FSN2E
Ceiling

1000
Min.
Wall Wall

630
Floor
Min. 300 1170 (1.5HP) Min. 300
1045 (1.0HP)

Floor Concealed Type

Models: RPFI-1.0FSN2E and RPFI-1.5FSN2E
Ceiling Ceiling

Upward Air Outlet

Short
1000
Min.

Flexible Duct Front Air Outlet

620
640

Floor Floor
Min. Min. Min. Min.
240 901 (1.5HP) 240 240 901 (1.5HP) 240
776 (1.0HP) 776 (1.0HP)

Service Space

Ceiling Type
Models: RPC-2.0FSN2, RPC-2.5FSN2, RPC-3.0FSN2, RPC-4.0FSN2 and RPC-5.0FSN2
(mm)
Min. 500

Min. 8

Min. 300 Min. 400

Min. 40

Total Heat Exchangers

Models: KPI-2521, KPI-5021, KPI-8021 and KPI-10021
Min. 200

EA RA
150 to 250

OA SA
Min. 600

450

Service Access
Door (450 x 450)

450

1-59
 SELECTION DATA

4.3 Sensible Heat Factor (SHF)

The sensible heat factor of indoor units at each fan speed (Hi, Me, Lo) based on the JIS Standard B8616, is
given in the below.

SHF
Model
Hi Me Lo
RPI-0.8FSN2 0.73 0.71 0.68
RPI-1.0FSN2 0.73 0.71 0.68
RPI-1.5FSN2 0.74 0.71 0.67
RPI-2.0FSN2 0.73 0.70 0.66
RPI-2.5FSN2 0.70 0.68 0.66
RPI-3.0FSN2 0.71 0.67 0.63
RPI-4.0FSN2 0.69 0.67 0.64
RPI-5.0FSN2 0.73 0.68 0.65
RPI-8FSN 0.72 - -
RPI-10FSN 0.71 - -
RCI-1.0FSN2 0.85 0.83 0.81
RCI-1.5FSN2 0.81 0.77 0.72
RCI-2.0FSN2 0.74 0.71 0.69
RCI-2.5FSN2 0.74 0.70 0.68
RCI-3.0FSN2 0.74 0.67 0.65
RCI-4.0FSN2 0.72 0.71 0.68
RCI-5.0FSN2 0.70 0.66 0.64
RCD-1.0FSN2 0.81 0.76 0.75
RCD-1.5FSN2 0.73 0.70 0.68
RCD-2.0FSN2 0.74 0.70 0.67
RCD-2.5FSN2 0.70 0.69 0.67
RCD-3.0FSN2 0.69 0.69 0.67
RCD-4.0FSN2 0.70 0.68 0.66
RCD-5.0FSN2 0.69 0.67 0.65
RPK-1.0FSNSM2 0.78 0.74 0.71
RPK-1.5FSNSM2 0.73 0.72 0.70
RPK-2.0FSNSM2 0.69 0.68 0.67
RPK-2.5FSNSM2 0.71 0.69 0.68
RPK-3.0FSNSM2 0.74 0.70 0.69
RPK-4.0FSNSM2 0.71 0.69 0.68
RPF-1.0FSN2E 0.73 0.69 0.65
RPF-1.5FSN2E 0.73 0.69 0.65
RPFI-1.0FSN2E 0.73 0.69 0.65
RPFI-1.5FSN2E 0.73 0.69 0.65
RPC-2.0FSN2 0.74 0.71 0.68
RPC-2.5FSN2 0.72 0.69 0.67
RPC-3.0FSN2 0.71 0.68 0.66
RPC-4.0FSN2 0.73 0.70 0.68
RPC-5.0FSN2 0.70 0.68 0.66

1-62
 SELECTION DATA

4.4 Fan Performance

RPI-0.8FSN2, 1.0FSN2 RPI-1.5FSN2

: Normal Mode (at shipping) : Normal Mode (at shipping)

150 : High Static Pressure Mode 150 : High Static Pressure Mode
: Low Staitc Pressue Mode : Low Staitc Pressue Mode
140 140

130 130

120 120

110 110
EXTERNAL STATIC PRESSURE (Pa)

EXTERNAL STATIC PRESSURE (Pa)

100 100

90 90

80 80 Hi
Hi
70 70

60 Me 60

Me Hi
50 50
Lo Hi
Me
40 40 Lo Me

30 Lo 30
Me Hi Hi
Lo Me
20 20
Lo
Lo
10 10

0 0
2 3 4 5 6 7 8 9 10 11 5 6 7 8 9 10 11 12 13 14
AIR VOLUME (m3/min) AIR VOLUME (m3/min)
The setting of Normal, High Static Pressure,and Low Static Pressure Mode The setting of Normal, High Static Pressure,and Low Static Pressure Mode
can be changed by Remote Control Switch. can be changed by Remote Control Switch.

RPI-2.0FSN2 RPI-2.5FSN2

: Normal Mode (at shipping) : Normal Mode (at shipping)

150 : High Static Pressure Mode 150 : High Static Pressure Mode
: Low Staitc Pressue Mode : Low Staitc Pressue Mode
140 140

130 130

120 120

110 110
EXTERNAL STATIC PRESSURE (Pa)

EXTERNAL STATIC PRESSURE (Pa)

100 100

90 90

80 Hi 80 Hi

70 70

60 60
Me Me
Hi Hi
50 50

40 40 Me
Lo Me Lo

30 30
Hi Me Hi
Lo Lo
Me
20 20
Lo Lo
10 10

0 0
7 8 9 10 11 12 13 14 15 16 8 9 10 11 12 13 14 15 16 18
AIR VOLUME (m3/min) AIR VOLUME (m3/min)
The setting of Normal, High Static Pressure,and Low Static Pressure Mode The setting of Normal, High Static Pressure,and Low Static Pressure Mode
can be changed by Remote Control Switch. can be changed by Remote Control Switch.

1-63
 SELECTION DATA

PI-3.0FSN2 RPI-4.0FSN2

320 320
: Normal Mode (at shipping) : Normal Mode (at shipping)
300 : High Static Pressure Mode 300 : High Static Pressure Mode
: Low Staitc Pressue Mode : Low Staitc Pressue Mode
280 280

260 260

240 240

220 220

EXTERNAL STATIC PRESSURE (Pa)

EXTERNAL STATIC PRESSURE (Pa)

200 200

180 180
Hi Hi

160 160

140 140
Me Hi
120 Hi
120
Me
Me 100
100 Me
Lo
80 Lo
80
Lo Hi
60 60
Lo Me Hi
Me
40 40
Lo
Lo
20 20

0 0
11 12 13 14 15 16 17 18 19 20 13 15 17 19 21 23 25 27 29 31
AIR VOLUME (m3/min) AIR VOLUME (m3/min)
The setting of Normal, High Static Pressure, and Low Static Pressure Mode The setting of Normal, High Static Pressure,and Low Static Pressure Mode
can be changed by Remote Control Switch. can be changed by Remote Control Switch.

PI-5.0FSN2

320
: Normal Mode (at shipping)
300 : High Static Pressure Mode
: Low Staitc Pressue Mode
280

260

240

220
EXTERNAL STATIC PRESSURE (Pa)

200

180
Hi
160

140

120 Hi
Me
100

80 Lo Me

60
Lo Hi
Me
40

Lo
20

0
23 25 27 29 31 33 35 37 39 41
AIR VOLUME (m3/min)
The setting of Normal, High Static Pressure,and Low Static Pressure Mode
can be changed by Remote Control Switch.

1-64
 SELECTION DATA

RPI-8FSN

High Static Pressure Setting: 220Pa (at shipping) High Static Pressure Setting: 260Pa (at shipping)
Low Static Pressure Setting: 110Pa
Low Static Pressure Setting: 130Pa
380V/50Hz
380V/60Hz 415V/50Hz
350 350

300 300

EXTERNAL STATIC PRESSURE (Pa)

EXTERNAL STATIC PRESSURE (Pa)

250 250
Lower Limit of Air Volume

Upper Limit of Air Volume

Upper Limit of Air Volume

Lower Limit of Air Volume

200 200

150 150

100 100

50 50

0 0
40 45 50 55 60 65 70 75 40 45 50 55 60 65 70 75
3
AIR VOLUME (m /min) AIR VOLUME (m3/min)
The setting of High Static Pressure and Low Static Pressure Mode can be The setting of High Static Pressure and Low Static Pressure Mode can be
changed by changing the position of the connector inside of the indoor unit. changed by changing the position of the connector inside of the indoor unit.

RPI-10FSN

High Static Pressure Setting: 220Pa (at shipping) High Static Pressure Setting: 260Pa (at shipping)
Low Static Pressure Setting: 110Pa
Low Static Pressure Setting: 130Pa
380V/50Hz
380V/60Hz 415V/50Hz
350 350

300 300
EXTERNAL STATIC PRESSURE (Pa)

EXTERNAL STATIC PRESSURE (Pa)

250 250
Upper Limit of Air Volume

Lower Limit of Air Volume

Upper Limit of Air Volume

Lower Limit of Air Volume

200 200

150 150

100 100

50 50

0 0
55 60 65 70 75 80 85 90 55 60 65 70 75 80 85 90
3
AIR VOLUME (m /min) AIR VOLUME (m3/min)
The setting of High Static Pressure and Low Static Pressure Mode can be The setting of High Static Pressure and Low Static Pressure Mode can be
changed by changing the position of the connector inside of the indoor unit. changed by changing the position of the connector inside of the indoor unit.

1-65
 SELECTION DATA

KPI-2521

Fan Performance and Heat Exchange Efficiency Curve Fan Performance and Heat Exchange Efficiency Curve

Model:KPI-2521 (50Hz) Model: KPI-2521 (60Hz)

90 90

Heat Exchange Efficiency (%)

Heat Exchange Efficiency (%)

Temperature Exchange Temperature Exchange

Efficiency Efficiency
80 80

70 70

60 Total Heat Exchanger Efficiency

60 Total Heat Exchange Efficiency
(Heating Operation) (Heating Operation)

Total Heat Exchanger Efficiency Total Heat Exchange Efficiency

(Cooling Operation) 50 250 (Cooling Operation)
50 250

150

150 200 Duct
200 Duct Length
Length
40m
Hi
External Static Pressure (Pa)

External Static Pressure (Pa)

40m
150
150
30m
Hi 30m Me
Me 100
100
20m
20m
Lo
Lo
50
50 10m
10m

0
0 0 50 100 150 200 250 300 350 400
0 50 100 150 200 250 300 350 400
3
Air Volume (m /h) Air Volume (m /h) 3

KPI-5021

Fan Performance and Heat Exchange Efficiency Curve Fan Performance and Heat Exchange Efficiency Curve
Model: KPI-5021
Heat Exchange Efficiency (%)

(50Hz) Model: KPI-5021

90 Total Heat Exchanger Efficiency
(Heating Operation)
Temperature Exchange (60Hz)
Efficiency 90
Heat Exchange Efficiency (%)

80
Temperature Exchange
80 400 Efficiency

70

Total Heat Exchanger Efficiency 70 350

(Heating Operation)
60 300

60 300
Total Heat Exchanger Efficiency
50 250 (Cooling Operation)
Total Heat Exchange Efficiency

200 (Cooling Operation)
Duct 50 250
Length
200
External Static Pressure (Pa)

200 Duct
Hi Hi
60m 200
Length
External Static Pressure (Pa)

60m
150 50m
50m
Me 40m
150

Lo Me 40m
100
30m Lo
100
30m
20m
50 20m
50
10m
10m
0
0 100 200 300 400 500 600 700 0
0 100 200 300 400 500 600 700
Air Volume (m3/h) Air Volume (m3/h)

1-66
 SELECTION DATA

KPI-8021

Fan Performance and Heat Exchange Efficiency Curve Fan Performance and Heat Exchange Efficiency Curve
Heat Exchange Efficiency (%)

Model:KPI-8021 (50Hz) Model: KPI-8021 (60Hz)

90 90
Temperature Exchange
Efficiency Temperature Exchange
Efficiency

80 600

Heat Exchange Efficiency (%)

80 600

70 500 70 500
Total Heat Exchanger Efficiency
(Heating Operation) Total Heat Exchange Efficiency
(Heating Operation)

60 400 60 400
Total Heat Exchanger Efficiency
(Cooling Operation) Total Heat Exchange Efficiency
(Cooling Operation)

50 300
250 50 300
250

Duct
External Static Pressure (Pa)

Duct
Length Hi
Hi

External Static Pressure (Pa)

Length
Lo 100m Lo 100m
200 200
80m 80m

Me 60m 60m
100
40m 100 Me
40m

20m 20m

0 0
0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200

Air Volume (m /h) 3 Air Volume (m3/h)

Do not use the condition that the External Static Do not use the condition that External Static
Pressure is under than 29Pa. Pressure is under than 29Pa.

KPI-10021

Fan Performance and Heat Exchange Efficiency Curve Fan Performance and Heat Exchange Efficiency Curve
Heat Exchange Efficiency (%)

Model:KPI-10021 (50Hz) Model: KPI-10021 (60Hz)

90 700
90 700
Temperature Exchange
Efficiency Temperature Exchange
Efficiency
Heat Exchange Efficiency (%)

80 600
80 600

70 500 Total Heat Exchanger Efficiency

(Heating Operation) 70 500 Total Heat Exchange Efficiency
(Heating Operation)

60 400 Total Heat Exchanger Efficiency

(Cooling Operation) 60 400 Total Heat Exchange Efficiency

250
Duct (Cooling Operation)
250
Length Duct
Hi Length
50 300 100m
50 300 100m
External Static Pressure (Pa)

Hi 80m Me
External Static Pressure (Pa)

Lo 80m
200 Lo
60m 200
60m
Me
40m
100 40m
100
20m
20m

0
0 200 400 600 800 1000 1200 1400 0
0 200 400 600 800 1000 1200 1400
3
Air Volume (m /h) Air Volume (m3/h)

Do not use the condition that the External Static Do not use the condition that External Static
Pressure is under than 49Pa. Pressure is under than 49Pa.

1-67
 ELECTRICAL DATA

5. Electrical Data
< 50 Hz >
Indoor Unit
Unit Main Power Applicable Voltage Indoor Fan Motor
Model
VOL PH HZ Maximum Minimum PH RNC IPT
RPI-0.8FSN2 0.5/0.5 0.10/0.11
RPI-1.0FSN2 0.5/0.5 0.10/0.11
RPI-1.5FSN2 0.7/0.7 0.14/0.15
RPI-2.0FSN2 0.7/0.7 0.14/0.15
220/240 1 50 264 198 1
In-the-Ceiling RPI-2.5FSN2 0.7/0.7 0.14/0.15
Type RPI-3.0FSN2 0.9/0.9 0.19/0.20
RPI-4.0FSN2 1.3/1.4 0.28/0.31
RPI-5.0FSN2 1.9/2.0 0.40/0.46
RPI-8FSN 1.6/1.6 0.99/0.99
380/415 3 50 456 342 3
RPI-10FSN 2.0/2.0 1.23/1.23
RCI-1.0FSN2 0.2/0.2 0.03/0.03
RCI-1.5FSN2 0.2/0.2 0.03/0.03
RCI-2.0FSN2 0.2/0.2 0.04/0.04
4-Way
RCI-2.5FSN2 220/240 1 50 264 198 1 0.3/0.3 0.06/0.06
Cassette Type
RCI-3.0FSN2 0.4/0.3 0.07/0.07
RCI-4.0FSN2 0.7/0.6 0.13/0.13
RCI-5.0FSN2 0.8/0.8 0.16/0.16
RCD-1.0FSN2 0.2/0.2 0.05/0.06
RCD-1.5FSN2 0.3/0.4 0.07/0.08
RCD-2.0FSN2 0.3/0.4 0.07/0.08
2-Way
RCD-2.5FSN2 220/240 1 50 264 198 1 0.4/0.5 0.09/0.11
Cassette Type
RCD-3.0FSN2 0.5/0.6 0.11/0.13
RCD-4.0FSN2 0.6/0.6 0.12/0.14
RCD-5.0FSN2 0.8/0.9 0.18/0.20
RPK-1.0FSNSM2 0.2/0.2 0.03/0.03
RPK-1.5FSNSM2 0.3/0.3 0.03/0.03
RPK-2.0FSNSM2 0.3/0.3 0.03/0.03
Wall Type 220/240 1 50 264 198 1
RPK-2.5FSNSM2 0.3/0.3 0.04/0.04
RPK-3.0FSNSM2 0.3/0.3 0.04/0.04
RPK-4.0FSNSM2 0.5/0.5 0.06/0.06
RPF-1.0FSN2E 0.2/0.2 0.04/0.04
Floor Type 220/240 1 50 264 198 1
RPF-1.5FSN2E 0.2/0.2 0.05/0.05
Floor RPFI-1.0FSN2E 0.2/0.2 0.04/0.04
220/240 1 50 264 198 1
Concealed Type RPFI-1.5FSN2E 0.2/0.2 0.05/0.05
RPC-2.0FSN2 0.4/0.4 0.08/0.09
RPC-2.5FSN2 0.5/0.5 0.09/0.12
Ceiling Type RPC-3.0FSN2 220/240 1 50 264 198 1 0.5/0.5 0.09/0.12
RPC-4.0FSN2 0.8/1.0 0.17/0.22
RPC-5.0FSN2 0.9/1.0 0.18/0.22

Total Heat Exchangers

Unit Main Power Applicable Voltage Indoor Fan Motor
Model
VOL PH HZ Max. Min. PH RNC IPT
KPI-2521 0.5/0.6 0.11/0.13
Total Heat KPI-5021 1.0/1.0 0.21/0.23
220/240 1 50 264 198 1
Exchangers KPI-8021 1.8/1.8 0.39/0.42
KPI-10021 2.3/2.3 0.50/0.53

VOL: Rated Unit Power Supply Voltage (Plated)(V) RNC: Running Current (A)
PH: Phase (
) IPT: Input (kW)
HZ: Frequency (Hz)

1-72
 ELECTRICAL DATA

< 60 Hz >
Indoor Unit
Unit Main Power Applicable Voltage Indoor Fan Motor
Model
VOL PH HZ Maximum Minimum PH RNC IPT
RPI-0.8FSN2 0.6 0.12
RPI-1.0FSN2 0.6 0.12
RPI-1.5FSN2 0.8 0.16
RPI-2.0FSN2 0.8 0.16
220 1 60 242 198 1
In-the-Ceiling RPI-2.5FSN2 0.8 0.16
Type RPI-3.0FSN2 1.2 0.26
RPI-4.0FSN2 1.5 0.32
RPI-5.0FSN2 2.3 0.49
RPI-8FSN 1.9 1.14
380 3 60 418 342 3
RPI-10FSN 2.3 1.41
RCI-1.0FSN2 0.2 0.03
RCI-1.5FSN2 0.2 0.03
RCI-2.0FSN2 0.2 0.04
4-Way
RCI-2.5FSN2 220 1 60 242 198 1 0.3 0.06
Cassette Type
RCI-3.0FSN2 0.4 0.07
RCI-4.0FSN2 0.7 0.13
RCI-5.0FSN2 0.8 0.16
RCD-1.0FSN2 0.2 0.05
RCD-1.5FSN2 0.4 0.08
RCD-2.0FSN2 0.4 0.08
2-Way
RCD-2.5FSN2 220 1 60 242 198 1 0.5 0.11
Cassette Type
RCD-3.0FSN2 0.6 0.13
RCD-4.0FSN2 0.7 0.14
RCD-5.0FSN2 1.2 0.24
RPK-1.0FSNSM2 0.2 0.03
RPK-1.5FSNSM2 0.3 0.03
RPK-2.0FSNSM2 0.3 0.03
Wall Type 220 1 60 242 198 1
RPK-2.5FSNSM2 0.3 0.04
RPK-3.0FSNSM2 0.3 0.04
RPK-4.0FSNSM2 0.5 0.06
RPF-1.0FSN2E 0.2 0.04
Floor Type 220 1 60 242 198 1
RPF-1.5FSN2E 0.2 0.05
Floor RPFI-1.0FSN2E 0.2 0.04
220 1 60 242 198 1
Concealed Type RPFI-1.5FSN2E 0.2 0.05
RPC-2.0FSN2 0.4 0.09
RPC-2.5FSN2 0.7 0.15
Ceiling Type RPC-3.0FSN2 220 1 60 242 198 1 0.7 0.15
RPC-4.0FSN2 0.9 0.20
RPC-5.0FSN2 0.9 0.20

Total Heat Exchangers

Unit Main Power Applicable Voltage Indoor Fan Motor
Model
VOL PH HZ Max. Min. PH RNC IPT
KPI-2521 0.6 0.13
Total Heat KPI-5021 1.2 0.26
220 1 60 242 198 1
Exchangers KPI-8021 2.1 0.46
KPI-10021 2.8 0.60

VOL: Rated Unit Power Supply Voltage (Plated)(V) RNC: Running Current (A)
PH: Phase (
) IPT: Input (kW)
HZ: Frequency (Hz)

1-73
 SOUND DATA

6. Sound Data

In-the-Ceiling Type

Model: RPI-0.8FSN2 Power Supply: 220V, 50/60Hz Model: RPI-1.0FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

70 NC-70 70 NC-70

60 NC-60 60 NC-60

50 NC-50 50 NC-50

40 NC-40 40 NC-40

Hi Hi

30 NC-30 30 NC-30

Me Me
Lo Lo

20 Approximate 20 Approximate
NC-2 NC-2
Threshold of 0 Threshold of 0
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RPI-1.5FSN2 Power Supply: 220V, 50/60Hz Model: RPI-2.0FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

70 NC-70 70 NC-70

60 NC-60 60 NC-60

50 NC-50 50 NC-50

40 NC-40 40 NC-40

Hi Hi
30 NC-30 30 NC-30

Me Me
Lo Lo

20 Approximate 20 Approximate
NC-2 NC-20
Threshold of 0 Threshold of
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-74
 SOUND DATA

Model: RPI-2.5FSN2 Power Supply: 220V, 50/60Hz Model: RPI-3.0FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve

Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

70 NC-70
70
NC-70

60 NC-60 60 NC-6
0

50 NC-50 50 NC-5
0

Hi

40 NC-40 40 NC-4
0
Me

Hi
30 NC-30 30 NC-3
0
Lo Me

Lo
20 Approximate
NC-2 20 Approximate NC-
20
Threshold of 0 Threshold of
Hearing for Hearing for
Continuous Noise Continuous Noise
10
10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RPI-4.0FSN2 Power Supply: 220V, 50-60Hz Model: RPI-5.0FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

70 NC-70 70 NC-70

60 NC-60 60 NC-60

50 NC-50 50 NC-50

Hi Hi
Me
40 NC-40 40 NC-40
Me

30 NC-30 30 NC-30

Lo Lo
20 Approximate 20 Approximate
NC-2 NC-2
Threshold of 0 Threshold of 0
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-75
 SOUND DATA

Model: RPI-8FSN Power Supply: 380V, 50/60Hz Model: RPI-8FSN Power Supply: 415V, 50Hz
Measurement Point: 1.5 Meter Beneath the Unit Measurement Point: 1.5 Meter Beneath the Unit
220Pa 260Pa
110Pa 130Pa
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 NC-70
70 70

60 NC-6 60 NC-6
0 0

50 NC-5 50 NC-5
0 0

40 NC-4 40 NC-4
0 0

30 NC-3 30 NC-3
0 0

Approximate
20 NC-
20 20 Approximate NC-
20
Threshold of Threshold of
Hearing for Hearing for
Continuous Noise Continuous Noise

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RPI-10FSN Power Supply: 380V, 50/60Hz Model: RPI-10FSN Power Supply: 415V, 50Hz
Measurement Point: 1.5 Meter Beneath the Unit Measurement Point: 1.5 Meter Beneath the Unit
220Pa 260Pa
110Pa 130Pa
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)
Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 NC-70
70 70

60 NC-6 60 NC-6
0 0

50 NC-5 50 NC-5
0 0

40 NC-4 40 NC-4
0 0

30 NC-3 30 NC-3
0 0

20 Approximate NC-
20 20 Approximate NC-
20
Threshold of Threshold of
Hearing for Hearing for
Continuous Noise Continuous Noise

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

NOTES:
1. The sound pressure level is based on following conditions, 1.5 Meter Beneath the Unit.
2. The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in
the field.

1-76
 SOUND DATA

4-Way Cassette Type

Model: RCI-1.0FSN2 Power Supply: 220-240V/220V, 50/60Hz Model: RCI-1.5FSN2 Power Supply: 220-240V/220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve

Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 NC-70
70 70

60 NC-6 60 NC-6
0 0

50 NC-5 50 NC-5
0 0

40 NC-4 40 NC-4
0 0
Hi Hi

Me
30 NC-3 30 NC-3
0 0
Me
Lo

Approximate
20 NC-
20 20 Approximate NC-
20
Threshold of Threshold of Lo
Hearing for Hearing for
Continuous Noise Continuous Noise

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000

Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RCI-2.0FSN2 Power Supply: 220-240V/220V, 50/60Hz Model: RCI-2.5FSN2 Power Supply: 220-240V/220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)
Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 NC-70
70 70

60 NC-6 60 NC-6
0 0

50 NC-5 50 NC-5
0 0

Hi

40 NC-4 40 NC-4
0 0

Me

30 NC-3 30 NC-3
0 0
Hi

Me
Approximate
20 Approximate NC- 20 NC-
Threshold of Lo 20 Threshold of 20
Hearing for Hearing for
Continuous Noise Continuous Noise Lo
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000

Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-77
 SOUND DATA

Model: RCI-3.0FSN2 Power Supply: 220-240V/220V, 50/60Hz Model: RCI-4.0FSN2 Power Supply: 220-240V/220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve

Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 NC-70
70 70

60 NC-6 60 NC-6
0 0

Hi

50 NC-5 50 NC-5
0 0

Hi

40 NC-4 40 NC-4
0 0
Me
Me

30 NC-3 30 NC-3
0 0

Approximate
20 Approximate NC-
20 20 NC-
20
Threshold of Threshold of
Hearing for Hearing for
Continuous Noise Lo Continuous Noise
Lo
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000

Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RCI-5.0FSN2 Power Supply: 220-240V/220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit

90
Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

80

NC-70
70

60 NC-6
0

Hi

50 NC-5
0

Me

40 NC-4
0

30 NC-3
0

Lo
20 Approximate NC-
20
Threshold of
Hearing for
Continuous Noise

10
63 125 250 500 1000 2000 4000 8000

Central Frequency (Cycle per Second)

1-78
 SOUND DATA

2-Way Cassette Type

Model: RCD-1.0FSN2 Power Supply: 220V, 50/60Hz Model: RCD-1.5FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 70 NC-70
70

60 NC-60 60 NC-60

50 NC-50 50 NC-50

Hi Hi
40 NC-40 40 NC-40

Me Me

30 NC-30 30 NC-30

20 Approximate 20 Approximate
NC-2
Threshold of NC-2 Threshold of 0
0
Hearing for
Lo Hearing for Lo
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RCD-2.0FSN2 Power Supply: 220V, 50/60Hz Model: RCD-2.5FSN2, RCD-3.0FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

70 NC-70 70 NC-70

60 NC-60 60 NC-60

50 NC-50 50 NC-50

Hi

Hi Me
40 NC-40 40 NC-40

Me

30 NC-30 30 NC-30

20 Approximate 20 Approximate
Threshold of NC-2 Threshold of NC-2
0 0
Lo Lo
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-79
 SOUND DATA

Model: RCD-4.0FSN2 Power Supply: 220V, 50/60Hz Model: RCD-5.0FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meters Beneath the Unit Measurement Point: 1.5 Meters Beneath the Unit
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 70 NC-70
70

60 NC-60 60 NC-60

Hi
50 NC-50 50 NC-50

Hi Me
Me
40 NC-40 40 NC-40

30 NC-30 30 NC-30
Lo
Lo
20 Approximate NC-2 20 Approximate NC-2
Threshold of 0 Threshold of 0
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-80
 SOUND DATA

Wall Type

Model: RPK-1.0FSNSM2 Model: RPK-1.5FSNSM2

Power Supply: 220V, 50/60Hz Power Supply: 220V, 50/60Hz
Measurement Point: 1 Meter Beneath the Unit and Measurement Point: 1 Meter Beneath the Unit and
1 Meter From Discharge Grille 1 Meter From Discharge Grille
90 90
Noise Criteria Curve Noise Criteria Curve

Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 NC-70
70 70

60 NC-6 60 NC-6
0 0

50 NC-5 50 NC-5
0 0

NC-4
Me NC-4
40 0 40 0
Hi Hi

30 NC-3 30 NC-3
0 0
Lo Me Lo

Approximate NC- Approximate

20 20 20
Threshold of Threshold of
NC-
Hearing for Hearing for 20
Continuous Noise Continuous Noise

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000

Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RPK-2.0FSNSM2 Model: RPK-2.5 FSNSM2, RPK-3.0FSNSM2

Power Supply: 220V, 50/60Hz Power Supply: 220V, 50/60Hz
Measurement Point: 1 Meter Beneath the Unit and Measurement Point: 1 Meter Beneath the Unit and
1 Meter From Discharge Grille 1 Meter From Discharge Grille
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 NC-70
70 70

NC-6 60 NC-6
60 0 0

NC-5 50 NC-5
50 0 0

Hi
Hi
NC-4 40 NC-4
40 0 0
Me

NC-3 Me
30 0 30 NC-3
Lo 0
Lo

Approximate
20 Approximate 20 Threshold of
Threshold of NC-
NC- Hearing for 20
Hearing for 20
Continuous Noise Continuous Noise

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000

Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-81
 SOUND DATA

Model: RPK-4.0FSNSM2
Power Supply: 220V, 50/60Hz
Measurement Point: 1 Meter Beneath the Unit and
1 Meter From Discharge Grille
90
Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

80

NC-70
70

60 NC-6
0

50 Hi NC-5
0

40 NC-4
0
Me

NC-3
0
30
Lo

Approximate NC-
20 20
Threshold of
Hearing for
Continuous Noise

10
63 125 250 500 1000 2000 4000 8000

Central Frequency (Cycle per Second)

1-82
 SOUND DATA

Floor Type

Model: RPF-1.0FSN2E Power Supply: 220V, 50/60Hz Model: RPF-1.5FSN2E Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meter from the Unit Measurement Point: 1.5 Meter from the Unit
1.5 Meter from Floor Level 1.5 Meter from Floor Level
Noise Criteria Curve Noise Criteria Curve
Hi/Me/Lo: 35/32/29 dBA Hi/Me/Lo: 38/35/31 dBA

80 80
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

70 70

60 60

50 50

40 40

30 30

20 20
Approximate Approximate
Threshold of Threshold of
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Floor Concealed Type

Model: RPFI-1.0FSN2E Power Supply: 220V, 50/60Hz Model: RPFI-1.5FSN2E Power Supply: 220V, 50/60Hz

Measurement Point: 1.5 Meter from the Unit Measurement Point: 1.5 Meter from the Unit
1.5 Meter from Floor Level 1.5 Meter from Floor Level
Noise Criteria Curve Noise Criteria Curve
Hi/Me/Lo: 35/32/29 dBA Hi/Me/Lo: 38/35/31 dBA

80 80
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

70 70

60
60

50 50

40 40

30 30

20 20
Approximate Approximate
Threshold of Threshold of
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-83
 SOUND DATA

Ceiling Type

Model: RPC-2.0FSN2 Power Supply: 220V, 50/60Hz Model: RPC-2.5FSN2, RPC-3.0FSN2 Power Supply: 220V, 50/60Hz

Measurement Point: 1 Meter Beneath the Unit and Measurement Point: 1 Meter Beneath the Unit and
90 1 Meter From Discharge Grille 90 1 Meter From Discharge Grille
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

70 NC-70 70 NC-70

60 NC-60 60 NC-60

50 NC-50 50 NC-50

40 NC-40 40 NC-40
Hi Hi

30 NC-30 30 NC-30

Me Me
Lo Lo
20 Approximate NC-2 20 Approximate NC-2
Threshold of 0 Threshold of 0
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: RPC-4.0FSN2 Power Supply: 220V, 50/60Hz Model: RPC-5.0FSN2 Power Supply: 220V, 50/60Hz
Measurement Point: 1 Meter Beneath the Unit and Measurement Point: 1 Meter Beneath the Unit and
90
1 Meter From Discharge Grille 1 Meter From Discharge Grille
90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

80 80

NC-70 70 NC-70
70

60 NC-60 60 NC-60

50 50
NC-50 NC-50

Hi Hi

40 40 NC-40
NC-40

30 NC-30 30 NC-30
Me Me

Lo Lo
20 Approximate 20 Approximate
NC-2 NC-2
Threshold of 0 Threshold of 0
Hearing for Hearing for
Continuous Noise Continuous Noise
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

1-84
 SOUND DATA
Total Heat Exchangers

Model: KPI-2521 Power Supply: 220-240V/50Hz Model: KPI-5021 Power Supply: 220-240V/50Hz
Measurement Point: 1.5 Meter Beneath the Unit Measurement Point: 1.5 Meter Beneath the Unit
and with a Sound-Proof Duct and with a Sound-Proof Duct
90 90
Noise Criteria Curve Noise Criteria Curve

80 80
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

NC-70 NC-70
70 70

60 NC-6
0 60 NC-6
0

NC-5 NC-5
50 0 50 0

NC-4
40 0 40 NC-4
0

30 NC-3
0 30 NC-3
0
Hi
Me
Lo Me Hi
20 NC-
20 20
Lo NC-20

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

Model: KPI-8021 Power Supply: 220-240V/50Hz Model: KPI-10021 Power Supply: 220-240V/50Hz
Measurement Point: 1.5 Meter Beneath the Unit Measurement Point: 1.5 Meter Beneath the Unit
and with a Sound-Proof Duct and with a Sound-Proof Duct
90 90
Noise Criteria Curve Noise Criteria Curve

80 80
Octave Sound Pressure Level (dB: Overall C Scale)

Octave Sound Pressure Level (dB: Overall C Scale)

NC-70 NC-70
70 70

60 NC-6
0 60 NC-6
0

50 NC-5 50 NC-5
0 0

40 NC-4
0 40 NC-4
0

Hi

Lo
30 NC-3
0 30 NC-3
0
Lo Me
Hi
Me NC-
20
20 20
NC-20

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)
NOTES:
1. The sound pressure level is based on following conditions, 1.5 Meter Beneath the Unit. (Total heat exchange mode)
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in
the field.
2. The sound pressure level emitted from the air outlet to the duct is higher than the values indicated in the GENERAL
DATA table by 5 to 6 dB(A) approximately. It is recommended that a sound-proof duct.

1-85
 SOUND DATA

Model: KPI-2521 Power Supply: 220V/60Hz Model: KPI-5021 Power Supply: 220V/60Hz
Measurement Point: 1.5 Meter Beneath the Unit Measurement Point: 1.5 Meter Beneath the Unit
and with a Sound-Proof Duct and with a Sound-Proof Duct
90 90
Noise Criteria Curve Noise Criteria Curve

Octave Sound Pressure Level (dB: Overall C Scale)

80 80
Octave Sound Pressure Level (dB: Overall C Scale)

70 NC-70 70 NC-70

60 NC-6 60 NC-6
0 0

50 NC-5 50 NC-5
0 0

40 Hi NC-4 40 NC-4
0 0
Hi

Me
Me
30 NC-30 30 NC-30
Lo
Lo

20 NC-2 20 NC-2
0 0

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second)
Central Frequency (Cycle per Second)

Model: KPI-8021 Power Supply: 220V/60Hz Model: KPI-10021 Power Supply: 220V/60Hz
Measurement Point: 1.5 Meter Beneath the Unit Measurement Point: 1.5 Meter Beneath the Unit
and with a Sound-Proof Duct and with a Sound-Proof Duct
90 90
Noise Criteria Curve Noise Criteria Curve
Octave Sound Pressure Level (dB: Overall C Scale)

80 80
Octave Sound Pressure Level (dB: Overall C Scale)

70 NC-70 70 NC-70

60 NC-6 60 NC-6
0 0

50 NC-5 50 NC-5
0 0

40 NC-4 40 NC-4
0 0

Hi
Hi

30 NC-30 30 NC-30
Me
Lo
Lo
Me

20 20 NC-2
0
NC-20

10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
Central Frequency (Cycle per Second) Central Frequency (Cycle per Second)

NOTES:
1. The sound pressure level is based on following conditions, 1.5 Meter Beneath the Unit. (Total heat exchange mode)
The above data was measured in an anechoic chamber so that reflected sound should be taken into consideration in
the field.
2. The sound pressure level emitted from the air outlet to the duct is higher than the values indicated in the GENERAL
DATA table by 5 to 6 dB(A) approximately. It is recommended that a sound-proof duct.

1-86
 ctrical Wiring Diagram

ELECTRICAL WIRING DIAGRAM (FOR MODELS: RPI-0.8FSN2, RPI-1.0FSN2, RPI-1.5FSN2, RPI-2.0FSN2, RPI-2.5FSN2, RPI-3.0FSN2, RPI-4.0FSN2 AND RPI-5.0FSN2)
CONTROL SYSTEM

1-139
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RPI-8FSN AND RPI-10FSN)
CONTROL SYSTEM

1-140
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RCI-1.0FSN2, RCI-1.5FSN2, RCI-2.0FSN2, RCI-2.5FSN2, RCI-3.0FSN2, RCI-4.0FSN2 AND RCI-5.0FSN2)
CONTROL SYSTEM

1-141
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RCD-1.0FSN2, RCD-1.5FSN2, RCD-2.0FSN2, RCD-2.5FSN2, RCD-3.0FSN2, RCD-4.0FSN2 AND RCD-5.0FSN2)
CONTROL SYSTEM

1-142
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RPK-1.0FSNSN2 AND RPK-1.5FSNSM2)
CONTROL SYSTEM

1-143
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RPK-2.0FSNSM2)
CONTROL SYSTEM

1-144
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RPK-2.5FSNSM2, RPK-3.0FSNSM2 AND RPK-4.0FSNSM2)
CONTROL SYSTEM

1-145
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RPF-1.0FSN2E, RPF-1.5FSN2E, RPFI-1.0FSN2E AND RPFI-1.5FSN2E)

Inlet Outlet Liquid Gas

for Communication
2 wire RCS (PC-AR)

INPUT OUTPUT1 OUTPUT2

Main Switch
1N~
220/240V
50Hz (3N~)
for RCS

1N~
220V/60Hz
(3N~)

Mark Name Remarks

CA Capacitor for Indoor Fan
Main Switch CN Connector
1~
DSW3 Unit Capacity Code On PCB
220V/60Hz DSW5 Refrigerant Cycle No. On PCB
(3~) DSW6 Unit Models Code On PCB
DSW7 Fuse Recover/Remote Controller Selector On PCB
RSW Indoor Unit No. Setting On PCB
EFR1,EFS1,EF1 Fuse On PCB
ITI Internal Thermostat for Indoor Fan Motor
LD1~3 Alarm Code On PCB
MIF Motor for Indoor Fan
MV Expansion Valve On PCB
PCB Printed Circuit Board
RCS Remote Control Switch Optional Part
RSW1, RSW2 Indoor Unit No. Settings On PCB
PCB Sockets location Electrical Control Box of Indoor Unit SSW Slide Switch
CN1 CN17 CN14 CN7 CN8 PCN5 PCN1 PCN6 PCN3 PCN11 PCN8 PCN10
TB Terminal Board
THM1 Inlet Air Thermistor On PCB
DM1 EF3
C2
THM2 Outlet Air Thermistor On PCB
THM3 Liquid Pipe Thermistor On PCB

SK1
C55

P
THM5 Gas Pipe Thermistor On PCB

(17G )
L1 Y52H
YH2 TF Transformer
C16 YME YLO YSLO YH1
YME Relay for ME Fan Motor Tap DC Coil
RSW2
YLO Relay for LO Fan Motor Tap DC Coil
DSW4 DSW5

PCN2
IC1 YSLO Relay for SLO Fan Motor Tap DC Coil
EFR1
DSW3
YH1 Relay for Hi Fan Motor Tap DC Coil
DSW6 RSW1
DSW7 Terminals
PCN7

TP THM4 THM2 EFS1

·X· Field Connection
CN2 EF2
– ·· – ·· – Field Wiring
CN19 CN5 CN10 CN11 CN3 THM5 THM3 THM1 CAUTION HIGH VOLTAGE - –- –- – Earth Wiring
–––––– Factory Wiring
CONTROL SYSTEM

1-146
 ELECTRICAL WIRING DIAGRAM (FOR MODELS: RPC-2.0FSN2, RPC-2.5FSN2, RPC-3.0FSN2, RPC-4.0FSN2 AND RPC-5.0FSN2)
CONTROL SYSTEM

1-147
 MISCELLANEOUS NOTES

11. Miscellaneous Notes

Special Notes
1. Provide a service access door near the unit 10. During heating operation, the outdoor heat
piping connection part on the false ceiling for the exchanger produces condensate dew or
cassette type units. melting water from frost.
2. Consider the air distribution from the unit to the Install the outdoor unit where drainage of
space of the room, and select a suitable location such water is convenient, or provide a drain
so that uniform air temperature in the room can passage.
be obtained. 11. Heating Performance: The heating capacity
Cassette and Ceiling Types - Avoid unit normally decreases when outdoor temperatures
installation in a room where the ceiling height decrease. Therefore, provide an auxiliary
(distance between the floor to the false ceiling) heating unit if outdoor temperatures are very
exceeds three meters. If the indoor unit is low.
installed in a room with a ceiling of higher than 3 12. In the case that an outdoor temperature is
meters, it is recommended that an air circulation low and humidity is high, the outdoor heat
fan be installed separately to obtain uniform air exchanger will covered with frost, resulting in
temperature in the room, especially during the lower heating capacity. In order to remove
heating operation. the frost, the unit is automatically changed to
3. Check to ensure that the ceiling slab is strong the defrosting mode. During this defrosting
enough and that the false ceiling is flat and level. operation, the unit is stopped for approximately
4. Avoid obstacles which may restrict the air intake 3 to 10 minutes.
or the discharge flow. 13. As this unit is of heat pump type by circulating
5. Do not install the unit in a machinery shop or hot air in the whole room space, it takes time to
kitchen where vapor from oil or its mist can enter heat up the room temperature.
to the unit. 14. The operating sound data is based on an
The oil will deposit on the heat exchanger, anechoic chamber. Therefore, the actual
thereby reducing the unit performance, and may operating sound will be higher due to reflected
deform, in the worst case, break the plastic parts sound from the floor and wall.
of the unit. 15. In the case that the unit is operated for a long
6. Pay attention to the following points when the time higher than the indoor temperature of
unit is installed in a hospital or other facilities 27oCDB or the humidity of 80%, dewing may
where electromagnetic wave is radiated from occur on the cabinets resulting in dew drops. If
medical equipment. dewing, it is required to add thermal insulator
(A) Do not install the unit where the on the cabinets.
electromagnetic wave is directly radiated to 16. Provide snow-protection hoods to prevent the
the electrical box, remote control cable or outdoor heat exchanger from snow clogging.
remote control switch. If the unit is operated in an are where it snows
(B) Install the unit and component as far as heavily, provide a base under the outdoor
practical (at least three meters) from the unit which should be 50cm higher than the
electromagnetic wave radiator. presumable maximum snow height.
(C) Prepare a steel box and install the remote 17. It is recommended that periodical service and
control switch in it. Prepare a steel conduit maintenance be performed by authorized
pipe and wire the remote control cable in it. service engineers before air conditioning
And then, connect earth wire with the box seasons, in order to avoid performance
and the pipe. decrease due to dust or dirt.
18. This heat pump air conditioner has been
(D) Install a noise filter when the power supply
designed for normal air conditioning for men.
emits harmful noise.
Do not apply to other purposes such as for
7. Do not install the units in an acid or alkaline food, animals, plants, high precision machines
environment due to the corrosive action on the or work of art. Also do not apply to vehicles
heat exchanger. In the case that outdoor units or vessels. It will results in water leakage or
are installed near the sea, it is recommended electrical leakage.
that optional corrosion-resistant type outdoor 19. It is recommended that the system be installed
unit be used. by authorized engineers. If not, it may cause
8. Do not install the units in a flammable water leakage, electric shock or fire.
environment due to the danger of an explosion. 20. In a place where fibers or dusts are floating, the
9. Regarding cassette type indoor units, consider air filter or heat exchangers or the drain pipe
the direct and reflected sound level, when may be clogged, resulting in water leakage
selecting the unit for spaces where extremely from the drain pan.
low sound is required.

1-149
 MISCELLANEOUS NOTES

Special Notes on Refrigerant, R410A

Use tools and measuring instruments only for the new refrigerant which is directly touch to refrigerant.

: Interchangeability is available with current R22 : only for Refrigerant R410A (No Interchangeability with R22)
: Prohibited : only for Refrigerant R407C (No Interchangeability with R22)
Interchangeability
Reason of Non-Interchangeability and Attention
Measuring Instrument and Tool with R22 Use
(: Strictly Required)
R410A R407C
Pipe Cutter Cutting Pipe
  -
Chamfering Reamer Removing Burrs
Flaring Tool 
  * The flaring tools for R407C are applicable to R22. Flaring for Tubes
* If using flaring tube, make dimension of tube larger Dimensional Control
Extrusion
 - for R410A. for Extruded Portion
Adjustment Gauge
* In case of material 1/2H, flaring is not available. of Tube after Flaring
* In case of material 1/2H, bending is not available. Bending
Pipe Bender  
Use elbow for bend and braze.
* In case of material 1/2H, expanding of tube is not Expanding Tubes
Refrigerant Expanding Tool  
available. Use socket for connecting tube.
Pipe
  * For
12.7,
15.88, spanner size is up 2mm. Connection of
Torque Wrench
  * For
6.35,
9.53,
19.05, spanner size is the same. Flare Nut
Brazing Tool   * Perform correct brazing work. Brazing for Tubes
* Strict Control against Contamin Prevention from
Nitrogen Gas   (Blow nitrogen during brazing.) Oxidation during
Brazing
* Use a synthetic oil which is equivalent to the oil used Applying Oil to
Lubrication Oil
  in the refrigeration cycle. the Flared Surface
(for Flare Surface)
* Synthetic oil absorbs moisture quickly.
* Check refrigerant cylinder color. Refrigerant Charging
Refrigerant
   Liquid refrigerant charging is required regarding
Cylinder
zeotoropic refrigerant.
 The current ones are applicable. However, it is Vacuum Pumping
Vacuum Pump  
required to mount a vacuum pump adapter which
Adapter for  can prevent from reverse flow when a vacuum pump
 
Vacuum Pump stops, resulting in no reverse oil flow.
* No interchangeability is available due to higher Vacuum Pumping,
Vacuum pressures when compared with R22. Vacuum Holding,
Manifold Valve  
Drying  Do not use current ones to the different refrigerant. Refrigerant Charging


If used, mineral oil will flow into the cycle and cause and Check of
Refrigerant
sludges, resulting in clogging or compressor failure. Pressures
Charge
Charging Hose   Connection diameter is different; R410A: UNF1/2,
R407C: UNF7/16.
Charging Cylinder   * Use the weight scale. -
Measuring
Weight Scale   - Instrument for
Refrigerant Charging
Refrigerant Gas  * The current gas leakage detector (R22) is not Gas Leakage Check
 
Leakage Detector applicable due to different detecting method.
: Interchangeability with R407C.

1-150
 STANDARD SPECIFICATIONS

Standard Specification for the

Hitachi Premium Range of Air Cooled Modular Set Free VRF Systems
Preamble Air cooled Condenser FSXN SERIES
The units shall be manufactured by Hitachi, and shall Cabinet - The cabinet shall be constructed from
meet or exceed the requirements of this specification. galvanized sheet complete with a baked polyester
Units shall be designed in accordance with the relevant powder coat finish. All fasteners exposed to the
standards, and tested to JIS Standard JIS B8616 weather shall be galvanized steel. The condenser
packaged air conditioner and shall be compliant cabinet shall be rated to IP 45, fully weatherproofed
with AS/NZS1677 refrigerating system. Units shall and suitable for outdoor operation, housing
be suitable for providing continuous operation in compressor, outdoor coil, condenser fan, motor
ambient conditions between -20˚C and 43˚C without and main electric controls interfacing Hitachi H-Link
excessive head pressure, unstable operation or icing. network. Access panel shall be provided for routine
Refrigerant shall be [Link] performance inspection and maintenance.
is to be fully documented within the manufacturers Compressor - Shall control inverter scroll
standard technical literature, and is to be measured compressor speed from 20HZ to 100HZ with 80
in accordance with JIS 8616. Noise spectrum results steps, quickly reach the set point then maintain in
commencing at the 63Hz band and finishing at the 8K a stable energy saving operation. FSXN8/10/12
Hz band are to be provided, along with an overall noise shall be fit with one inverter driven scroll compressor
level Noise data is to be provided for the following: and FSXN14/16/18 shall be fit with one inverter
Indoor unit driven scroll compressor and one constant scroll
• Sound Pressure Level compressor. Compressor shall be protected by a
• Outdoor Unit quick response over current relay, a high pressure
Sound Pressure Level switch, a wrap around type oil heater and a discharge
• Sound Power Level gas thermistor. Crankcase heater shall be factory
supplied and mounted.
System description
Condenser Fan - Shall be plastic propeller type
The variable capacity heat pump as well as heat fan direct driven by variable speed motor with
recovery air conditioning system shall be Hitachi permanently lubricated bearings for vertical flow
inverter driven Modular FSXN series that use universal air discharge. Propeller fan shall be statically and
condensing units with R410A refrigerant. The FSXN dynamically self balanced. Fan shall be provided with
Series shall be either 3 pipe heat recovery multi guard to prevent from contact with moving parts.
split inverter system or 2 pipe heat pump multi split
Refrigeration Circuit - Shall include, but not be
system. The base module shall be FSXN8/10/12 and
limited to the following:
FSXN14/16/18 and shall be capable to form up to
54HP with 3 standard modules. • DC inverter scroll Compressor/s
The 3 pipe heat recovery system shall consist • Electronic Expansion Valve
of Hitachi Modular FSXN outdoor unit/s, CH • Head Pressure Control
(changeover) Boxes, multiple indoor units and
• Common fault indication
associated local and central controls. Each indoor
unit or group/zone shall be capable of operating • Anti short cycle timer
independently and system shall be capable of • Frost protection
operating in either cooling, heating or simultaneous • Liquid & Suction service valves
cooling and heating mode. Each indoor unit or
group/zone shall be able to change mode with no • Di – Ice control based on time/temperature initiation
interruption to whole system operation. - Hot gas by – pass defrost type control
The 2 pipe heat pump system shall consist of Hitachi shall not be used
FSXN outdoor unit/s, multiple indoor units and • DC inverter Compressor – scroll compressor
associated local and central controls. Each refrigerant - Crank case heater fitted to the compressor
group shall be capable of operating independently and
system shall be capable of operating in either cooling - The compressor is to be located within an
or heating mode. isolated compressor compartment
The single VRF system shall be capable of handling • Compressor minimum run time
range from 50%-130% connected indoor capacity Condenser Coil - Shall be multi pass, cross finned
and up to 64 indoor units without unstable operation. tube type manufactured by Hitachi, and will comprise
The total refrigerant piping length shall be able to run copper tube, complete with anti corrosion aluminium
up to 1000 m max and Max single piping length shall fin stock mechanically bonded to the copper tubes.
be able to run up to 165 m. The lift between outdoor Frames shall be aluminium, suitable for outdoor use.
and indoor units shall be within 50m. The coil shall be designed to allow for the full coil

1-151 A
 STANDARD SPECIFICATIONS

to be de-frosted where necessary. Coil shall be within 300mm. The cabinet shall include indoor
cleaned, dehydrated and pressure tested at factory coils, piping, supply air fan, drain pump, electronic
and shall be charged with correct refrigerant charge expansion valve, control circuit board, accessories
before shipment. and electrical connections mounted within an
Clearance shall be provided around units for condenser insulated enclosure. Facial Panel shall be either a
air flow and maintenance access. Hot discharge air four-way or a two-way air distribution type, impact
shall not be short-circuited to condenser intake. resistant, stain resistant and washable decoration
panel. The supply air is distributed via motorized
CH Change Over Box louvers which can be horizontally and vertically
Cabinet - The cabinet shall be compact, light adjusted from 0° to 90°. Access panels shall be
weight, constructed from galvanized sheet complete easily removed and sized to provide adequate
with high density foam insulation suitable for indoor access to interior for routine inspection and
installation. All fasteners exposed to the weather shall maintenance, and shall be air tight. The cabinet is
be galvanized steel. The sheet metal cabinet shall be to be insulated for thermal & acoustic performance,
housing expansion valves, refrigeration control solenoid using polyethylene insulation.
valves, control circuit board and other electric controls Evaporator Coil - Shall be manufactured
interfacing Hitachi H-Link network. Access panel shall by Hitachi, and shall be direct expansion type
be provided for routine inspection and maintenance. manufactured from inner grooved copper tubes
Changeover box shall be capable of control refrigerant expanded into aluminum fins to form a mechanical
flow for either one unit or a group of up to 8 units. bond. Coil shall be pressure tested at factory
It shall have 2 incoming gas pipes (low pressure and and shall be charged with dry air or dry nitrogen
high pressure) and 1 outgoing gas pipe. Liquid pipe before shipment.
shall not be run through changeover box to save Condensate Drain Pan - Shall be sized and
on pipe joints. sloped to catch all condensate, and to allow it to
Ducted Indoor Unit RPI SERIES drain away freely, and shall be constructed to be
Cabinet - Shall be fabricated using galvanized steel corrosion resistant. A condensate pan with drain
with high density foam insulation. The cabinet shall connections shall be provided under the coil.
include indoor coils, piping, supply air fan, motor, The unit shall also include a built-in, automatic
electronic expansion valve, control circuit board, condensate lift mechanism that will be able to
accessories and electrical connections mounted raise drain water 850mm above the condensate
within an insulated enclosure with four brackets to pan. The lift mechanism shall be equipped with
accommodate suspension. Access panels shall be a positive acting liquid level sensor to shut down
easily removed and sized to provide adequate access the indoor unit if liquid level in the drain pan
to interior for routine inspection and maintenance, reaches maximum level.
and shall be air tight. The cabinet is to be insulated Evaporator Fan - Shall be direct drive turbo
for thermal & acoustic performance, using fan, minimum 3 speeds. Indoor turbo fan shall
polyethylene insulation. be statically and dynamically self balanced and
Evaporator Coil - Shall be manufactured by Hitachi, shall be driven by high efficient DC fan motor with
and shall be direct expansion type manufactured from permanently lubricated bearings.
inner grooved copper tubes expanded into aluminum The four-way indoor unit shall have an adjustable
fins to form a mechanical bond. Coil shall be pressure air outlet system offering 4-way airflow, 3-way
tested at factory and shall be charged with dry air or airflow, or 2-way airflow with switches that can be
dry nitrogen before shipment. set to provide optimum airflow based on ceiling
Condensate Drain Pan - Shall be sized and height and number of outlets used.
sloped to catch all condensate, and to allow it to Wall Mounted Indoor Unit RPK SERIES
drain away freely, and shall be constructed to be
corrosion resistant. Cabinet - Shall be fabricated with high strength
moulded plastic and sufficient insulation and shall
Evaporator Fan - Shall be direct drive centrifugal be suitable to be mounted firmly on the factory
fan, minimum 3 speeds. Indoor centrifugal fan shall be supplied mounting template. It Shall include indoor
statically and dynamically self balanced and shall be coils, piping, supply air fan, motor, electronic
driven by high efficient DC fan motor with permanently expansion valve, control circuit board, accessories
lubricated bearings. Fan curves showing the airflow and electrical connections within an insulated
limits, available external static, and input power for enclosure. Front panel shall be easily removed
each fan speed are to be documented within the to provide access to interior of unit for routine
manufacturer’s standard literature. inspection and maintenance.
Cassette Indoor Unit RCI/RCD SERIES Evaporator Coil - Shall be manufactured
Cabinet - Shall be fabricated using galvanized steel by Hitachi, and shall be direct expansion type
coated with high density foam insulation with unit height manufactured from inner grooved copper tubes

1-151 B
 STANDARD SPECIFICATIONS
expanded into aluminum fins to form a mechanical Condensate Drain Pan - Shall be sized and
bond. Coil shall be pressure tested at factory and sloped to catch all condensate, and to allow it to
shall be charged with dry air or dry nitrogen drain away freely, and shall be constructed to be
before shipment. corrosion resistant.
Condensate Drain Pan - Shall be sized and Evaporator Fan - Shall be sirocco type fan direct
sloped to catch all condensate, and to allow it to driven by single phase motor with permanently
drain away freely, and shall be constructed to be lubricated bearings, minimum 3 speeds. Indoor sirocco
corrosion resistant. fan shall be statically and dynamically balanced.
Evaporator Fan - Shall be tangential type fan Control
direct driven by single phase motor with permanently General - shall consist of Hitachi local control,
lubricated bearings, minimum 3 speeds. Indoor central control, central on/off control, schedule timer,
tangential fan shall be statically and dynamically web based CS Net and Open interface including
balanced. Bacnet and Lonworks gateway.
Under ceiling Mounted Indoor Unit RPC SERIES Wiring - Shall be no-polar 2 conductor, twisted
Cabinet - Shall be fabricated with galvanised steel shielded pair and shall be wired in daisy chain
with white power coating and sufficient insulation and configuration from outdoor units to changeover boxes
shall be suitable to be mounted firmly under ceiling. and from changeover box to indoor units. Control
It Shall include indoor coils, piping, supply air fan, wiring for central control, schedule timer, CS net
motor, electronic expansion valve, control circuit shall be installed in daisy chain from outdoor units to
board, accessories and electrical connections within outdoor units and to these controls.
an insulated enclosure. Front panel shall be easily Local Remote Control - shall be LCD wired remote
removed to provide access to interior of unit control PC-AR OR PC-ART with weekly timer function.
for routine inspection and maintenance.
General: Provide microprocessor controller with the
Evaporator Coil - Shall be manufactured by Hitachi, following functions:
and shall be direct expansion type manufactured from
- Power ON/OFF switch.
inner grooved copper tubes expanded into aluminum
fins to form a mechanical bond. Coil shall be pressure - Mode selector switch:
tested at factory and shall be charged with dry air or DEHUMIDIFY - COOL - HEAT - AUTO
dry nitrogen before shipment. - Temperature settings
Condensate Drain Pan - Shall be sized and - Evaporator fan speed selector
sloped to catch all condensate, and to allow it to - Indicating lamps, LEDs or LCD display for unit
drain away freely, and shall be constructed to be operating or fault
corrosion resistant. - Self diagnosis functions
Evaporator Fan - Shall be sirocco type fan - Group control up to 16 units by one single control
direct driven by single phase motor with permanently Central Control - shall be LCD wired control or web
lubricated bearings, minimum 3 speeds. Indoor based as listed,
sirocco fan shall be statically and dynamically
- Schedule timer: PSC-A1T (weekly timer with
balanced.
3 programs/day, winter and summer schedule)
Floor Mounted Indoor Unit RPF/RPFI SERIES - Central on/off control: PSC-A16RS (up to 16 groups
Cabinet - Shall be fabricated with galvanised or 160 units collectively on/off control)
steel for floor concealed type and galvanised steel - Central station control: PSC-A64S OR PSC-5S
with white power coating for floor exposed type (up to 64 groups or 160 units collectively control)
and sufficient insulation and shall be suitable to
- Web based control: PSC-6WTX (up to 64 groups or
be mounted firmly on the floor. It Shall include
1024 units collectively control over net)
indoor coils, piping, supply air fan, motor, electronic
expansion valve, control circuit board, accessories Quality assurance
and electrical connections within an insulated The complete VRF system shall be designed
enclosure. Front panel shall be easily removed within the guarantee working range published in the
to provide access to interior of unit for routine technical literature and installed within guide line of
inspection and maintenance. manufacturer published technical literature and shall
Evaporator Coil - Shall be manufactured by Hitachi, be commissioned and certified by factory trained
and shall be direct expansion type manufactured from technicians or factory trained agents.
inner grooved copper tubes expanded into aluminum The complete system shall be complete assembled
fins to form a mechanical bond. Coil shall be pressure and tested in ISO9001 and ISO14001 certified
tested at factory and shall be charged with dry air or manufacturing facilities and shall be tested to comply
dry nitrogen before shipment. with current Australian safety and EMC standards.

1-151 C
 IMPORTANT NOTICE

• Upon receiving this product, inspect it for any shipping damage.

Claims for damage, either apparent or concealed, should be filed immediately with the shipping company.
• Check the model number, electrical characteristics (power supply, voltage and frequency) and accessories
to determine if they are correct.

The standard utilization of the unit shall be explained in these instructions.

Therefore, the utilization of the unit other than those indicated in these instructions is not recommended.
Please contact your local agent, as the occasion arises.
HITACHI’s liability shall not cover defects arising from the alteration performed by a customer without
HITACHI’s consent in a written form.

CAUTION
• Use shielded wires of operation line between the indoor unit and the outdoor unit.
And connect the shielded part to the earth screw in the electrical box of the indoor unit as shown in the Fig. 1.
(Example: RPI-8FSN)
Protect the earth wire not to contact
with the live part.

Earth Terminal TB1

*Earth the tip of shield wires

as shown.

TB2

A B 1 2

Shielded
DO NOT connect the wiring Part
to these terminals. (TB1-1,2)

Remote Control Transmission Cable

Power Source Cable
Switch Cable

*In case of Australia, ensure to

earth shield wire tip of both ends.

*ELB *ELB: Earth Leakage Breaker

Power
Source

Fig. 1 Earth Wiring