Doc. nr.

: DSDL_21010_A

Data Sheet And Service Manual

EC9155 LA SPECIALISTA ARTE (ALL COUNTRIES)

Date: 14.06.2021

INDEX / INDICE:

1. TECHNICAL DATA ................................................................................................................................... 2

2. HYDRAULIC DIAGRAM ........................................................................................................................... 3
3. 4 WIRING DIAGRAM ................................................................................................................................ 4
5. WORKING PRICIPLE ............................................................................................................................... 6
6. TEST MODE ............................................................................................................................................... 7
7. TROUBLESHOOTING ............................................................................................................................ 12

[1]
 Doc. nr.: DSDL_21010_A

1. TECHNICAL DATA

Voltage 220-240v / 50-60 Hz (INT – AU/NZ)

120v / 60 Hz (US/CA)

Max. input power 1550 W

COMPONENTS

Pump 220-240v AC - 48 W (INT – AU/NZ)

120v AC - 52 W (US/CA)

Grinder motor 230 V Ac (INT – AU/NZ) - 120v AC (US/CA)

Solenoid valves EV1 EV2 230 V Ac (INT – AU/NZ) - 120v AC (US/CA)

Coffee thermoblock
- Temperature probe NTC sensor
- Thermal fuse TCO 192 °C
- Heating element 230v AC – 1400 W - (INT – AU/NZ)
120v AC – 1400 W - (US/CA)

NTC temperature characteristics (thermoblock)

[2]
 Doc. nr.: DSDL_21010_A

2. HYDRAULIC DIAGRAM

[3]
 Doc. nr.: DSDL_21010_A

3. WIRING DIAGRAM

[4]
 Doc. nr.: DSDL_21010_A

3. WIRING DIAGRAM

[5]
 Doc. nr.: DSDL_21010_A

5. WORKING PRINCIPLE

MICROSWITCHES, SENSORS AND ELECTROVALVES

MICROSWITCHES Function Logic

Detects when the sump is inserted
MICROSWITCH FILTER HOLDER NO when the sump is NOT inserted
In order to start grinding

REED Function
Detects when the water level is at
REED SENSOR WATER TANK
minimum

ELECTROVALVES Function
EV1 = 2 ways HOT WATER solenoid Allows the hot water flow going to
valve the hot water pipe
First allow steam to flow to the
EV3. When steam flow stops close
the way to EV3 and opens the 3rd
EV2 = 3 ways STEAM solenoid valve
way to discharge residual steam
pressure on the expansion
chamber (then to the drip tray)
Allows steam from EV2 to flow up
EV3 = 3 ways WATER solenoid valve
to the steam pipe

[6]
 Doc. nr.: DSDL_21010_A

6. TEST MODE

6.1. HOW TO ENTER IN THE VARIOUS TEST MODES/STATISTICS

6.2. USER INTERFACE TEST
6.3. FUNCTIONAL TEST
6.4. LOAD TEST

6.5. INPUT TEST

6.6. STATISTICS

User Interface CONTROLS

6.1.HOW TO ENTER IN THE VARIOUS TEST MODES/STATISTICS

A. SET THE POSITION OF THE TASTE KNOB AND KEEP THE SWITCH AS FOLLOW:
TEST DOSE KNOB BEVERAGES KNOB
USER INTERFACE TEST MIN ESPRESSO
FUNCTIONAL TEST MIN AMERICANO/LONG BLACK
LOAD TEST MIN HOT WATER
INPUT TEST MIN DESCALING
STATISTICS MAX --
B. TURN ON THE COFFEE MACHINE BY THE MAIN SWITCH WHILE THE X1/X2 IS PUSHED FOR MORE THAN
5S.
C. TO EXIT FROM THE TEST MODE SWITCH OFF THE COFFEE MACHINE BY THE MAIN SWITCH.

[7]
 Doc. nr.: DSDL_21010_A

6.2.USER INTERFACE TEST

In this mode while the button is pressed the correspondent led switch on, the potentiometer knobs need to berotated on the most anti-clockwise position
in order to not create interference. When the potentiometer knobwill be rotate clockwise (only one at a time) the leds switch on according the next
tables.

SWITCH LEDS STATE

PUSHED X1/X2 OK TEMP1/2/3 STEA
(WHITE/ORANGE) M
X1/X2 ON ALTERNATING OFF OFF OFF

OK OFF ON ALTERNATING OFF OFF

TEMPERATURE OFF OFF ON ALTERNATING OFF

STEAM OFF OFF OFF ON

COFFEE TASTE POTENTIOMETER

KNOB POSITION LEDS STATE
DESCALE TANK X2

>=180 OFF OFF ON

120 <= ADC < OFF ON OFF
180
60 <= ADC < 120 ON OFF OFF

ADC < 60 OFF OFF OFF

BEVERAGE LENGTH POTENTIOMETER

KNOB POSITION LEDS STATE
ESPRESSO HOT WATER AMERICANO

DESCALE OFF OFF OFF

HOT WATER OFF ON OFF
AMERICANO/LONG OFF OFF ON
BLACK
ESPRESSO ON OFF OFF

[8]
 Doc. nr.: DSDL_21010_A

6.3.FUNCTIONAL TEST
TEST STEP LOAD STATE
SWITCH PUMP 3WAY WATER STEAM HEATER GRINDER LED
STATE VALVE E- E-
VALVE VALVE
“STEAM”
STEAM FLASH,
HYDRAULIC STEAM ON ON OFF ON OFF OFF
Others OFF
CIRCUIT
“COFFEE”
OK Flash,
HYDRAULIC OK PUSHED ON OFF OFF OFF OFF OFF
Others OFF
CIRCUIT
“HOT
WATER” X2 X1 Flash,
ON OFF OFF OFF OFF OFF
HYDRAULIC PUSHED Others OFF
CIRCUIT
OK Flash on
EMPTYING execution,
TEMP
HYDRAULIC Emptying procedure BLINK TEST
PUSHED
CIRCUIT and OK ON at
the end
TEMP
PUSHED
FACTORY Reset parameters to default and to first trigger. Reset relative OK Flash few
+
RESET BEV. KNOB counters to zero. times
ON
DESCALING

[9]
 Doc. nr.: DSDL_21010_A

6.4.LOAD TEST
LOAD SWITCH LOAD STATE LED STATE
STATE PUM 3WA WATE STEAM HEATE GRINDE
P Y EV R EV EV R R
3WAY VALVE X1/X2 OFF ON OFF OFF OFF OFF X1 ON,
Others OFF
PUMP OK ON OFF OFF OFF OFF OFF OK ON,
Others OFF
HEATER TEMP OFF OFF OFF OFF ON OFF TEMP low ON,
110 °C Others OFF
ELECTROVALV X2+STEA Others OFF
E M
STEAM STEAM OFF OFF OFF ON OFF OFF Steam ON,
ELECTROVALV Others OFF
E
GRINDER GRIND OFF OFF OFF OFF OFF ON
SWITCH

[10]
 Doc. nr.: DSDL_21010_A

6.5. INPUT TEST

INPUT LED STATE
FILTER HOLDER DESCALING LED ON IF DESCALING LED OFF IF
(GRINDER SIDE) SWITCH RELEASED SWITCH PRESSED
TANK REED TANK ALARM LED TANK ALARM LED
ON IF REED OPEN OFF IF REED CLOSED
(NO MAGNET) (MAGNET PRESENT)

6..6. STATISTICS
 Turn the Knob to select the correct statistics would you like to show, so press OK to show it
 The number of blinks specifies the units, tens, hundreds, thousands and tens of thousands of
every statistic.
 Every digit is separated from the others switching off all LEDs for 2s.

DIGIT LED
UNITS STEAM
DOZENS TEMP LOW
HUNDERS OK
THOUSANDS X1
TENS OF TANK
THOUSANDS

BEVERAGE/FUNCTION STATISTIC INPUT STATE FOR SELECTION

ESPRESSO WATER LITERS ON COFFE BEVERAGES KNOB ON ESPRESSO
AMERICANO/LONG WATER DECILITERS ON STEAM BEVERAGES KNOB ON LONG
BLACK BLACK
HOT WATER WATER LITERS ON WATER BEVERAGES KNOB ON COFFEE

DESCALING NUMBER OF DESCALINGS BEVERAGES KNOB ON DESCALING

PERFORMED

[11]
 Doc. nr.: DSDL_21010_A

7. TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
There is water in the drip tray (A19) It is normal: due to the internal water Regularly empty and clean the drip tray
circuits operations
No espresso coffee is delivered No water in the tank (A7) Fill the tank
Only the OK light (B6) is on to indicatethat Press the button corresponding to the OK
the coffee or steam circuit is empty light to fill the circuit
The coffee filter (C3) or (C4) is blocked Rinse the filters under abundant running
water.
Coffee grind too fine or too much coffee Adjust coffee dose and grinding (refer toQuick
Guide)
The tank (A7) has been inserted Press the tank down lightly to open thevalves
incorrectly and the valves on the bottom on the bottom
are not open
Scale in the water circuit Descale as described in section “9. Descaling”
The portafilter (C1) cannot be attachedto the The ground coffee has not been pressedor is Repeat grinding with new settings. Reduce the
appliance too much powder quantity: check if the filter (sin- gle or
double filter) is the same size as theselector of
grinding quantity (2x (B5) select-ed or not)

The espresso coffee drips from the edges The portafilter is inserted incorrectly Attach the portafilter correctly and rotatefirmly
of the portafilter (C1) rather than the holes as far as it will go
The espresso boiler gasket has lost Have the espresso boiler gasket replaced by
elasticity or is dirty Customer Services
The coffee filter is clogged • Rinse the filters under abundant running
water.
• Reduce the grinding thickness
The coffee crema is too light (deliveredfrom The appliance settings need reviewing Refer to Quick Guide for suggestions
the spout too fast)
The coffee crema is too dark (deliveredfrom The appliance settings need reviewing Refer to Quick Guide for suggestions
the spout too slowly)
At the end of descaling, the appliance During the rinse cycle, the water tank (A7) Complete the rinse cycle from point (8) of sec-tion“9.
requests a further rinse has not been filled to the MAXlevel Descaling”

The appliance does not grind the coffee There is foreign matter that cannot beground Turn the grinder selector (A2) to 8, vacum all the
in the coffee grinder beans and particles in the beans container(A3). If the
problem persists, address to Cus- tomer Service
Centre.
… →

[12]
 Doc. nr.: DSDL_21010_A

PROBLEM CAUSE SOLUTION

If you want to change the type of coffee You must remove all the beans presentin the • Empty the beans container (A3) (if nec- essary,
machine operate the coffee mill without beans or use
a vacuum cleaner to re- move any
remaining beans)
• Attach the portafilter (C1) and operate the
coffee mill a number of times with- out beans
to free the grinder. Attach the portafilter to
the outlet of the grinder (A13). Push the
portafilter to start grinding: it stops
automatically. Repeat until the filter is empty
• Place the new coffee in the beans
container
• If the amount of coffee ground is not
enough to reach the perfect dose, pro- ceed
setting the appliance as for the first use

After grinding, the coffee filter is empty The coffee grinder funnel is clogged See section “6. Cleaning the grinder”.
After grinding, the ground coffee in the filter The quantity of ground coffee needs Adjust the quantity of coffee with the dial (B4). If
(C3) or (C4) does not reach the “perfect adjusting the dial is already in the max. position, select the
dose” second range of grinding adjust- ment (see “3.
Menù settings”- “Extra grinding adjustment”).

You are using the 2 cup filter (C4) Make sure the 2X light is on
Over time the burrs wear down Address to a Customer Service Centre to
change burrs.

[13]