EM5203J/AJ

2A Current-Limited Power Distribution Switches

General Description Applications
The EM5203J/AJ is an N-channel MOSFET
⚫ USB
high-side power switch without parasitic body
⚫ Notebook & Netbook &MB
diode between drain and source. The EM5203J/AJ
provides very low on-resistance as 60m and Pin Configuration
continuously delivers up to 2.1A output current.
The fault flag output function indicates fault 5 VIN
OUT
conditions to the local USB controller. The other
features include soft start, current limit protection, GND 2
Power-On-Reset function, and over temperature
OC# 3 4 EN / EN#
protection. The EM5203J/AJ is available in
SOT23-5L package. SOT23-5

Ordering Information
Part Number Package Remark Typical Application Circuit
EM5203AJ-20 SOT23-5 2A/Active High

EM5203J-20 SOT23-5 2A/Active Low

VIN VIN OC#

Features
GND VOUT VOUT
⚫ Wide Input Range 2.5V to 5.5V
EM5203
⚫ Low MOSFET On Resistance(60m)
⚫ 2us Short Protection Response Enable
EN (EN#)
⚫ Low Quiescent(65uA) & Shutdown Current Disable

⚫ Deglitched Open-Drain Fault Flag Output

⚫ Reverse Current Flow blocking
Note: A low ESR 150uF capacitor between VOUT &
⚫ Power On Reset Function GND is recommended.
⚫ Current Limit Protection
⚫ Over Temperature Protection
⚫ Soft Start and Fast turn off
⚫ Reverse Voltage Protection
⚫ Enable Active High or Active Low
⚫ UL Recognized, File No.E468218

2023/06/08
A.10 1
 EM5203J/AJ
Pin Assignment
Pin Name Pin No. Pin Function

GND 2 Ground.
Input Voltage. This is the drain input to the power device that supplies current to
VIN 5 the output pin. Minimum 1uF low ESR ceramic capacitor is recommended at this
pin.
EN / EN# 4 Chip Enable Input (Active high for EN, Active low for EN#)
OC Flag Output. This is an open-drain output and is set low impedance once
OC# 3
current limit or over temperature protection enabled.
VOUT 1 Output Voltage. VOUT is power output pin.

Function Block Diagram

EN / EN# VIN

Current
Power On
Limit
Reset

Charge Control
Oscillator Logic
Pump
VOUT
Thermal
Protection OC#

GND
Deglitch

Absolute Maximum Ratings (Note1)

⚫ VIN ----------------------------------------------------------------------------------------------------- -0.3V to +6.0V
⚫ Other Pins-------------------------------------------------------------------------------------- -0.3V to (VIN+0.3V)
⚫ Power Dissipation, PD @ TA = 25C, SOT23-5 -------------------------------------------------------- 0.4W
⚫ Thermal Resistance Junction to Ambient, θJA, SOT23-5 (Note 2)---------------------------- 250C/W
⚫ Thermal Resistance Junction to Case, θJC, SOT23-5 (Note 2)---------------------------------- 60C/W
⚫ Junction Temperature-------------------------------------------------------------------------------------- 150C
⚫ Lead Temperature (Soldering, 10 sec.)--------------------------------------------------------------- 260C
⚫ Storage Temperature -------------------------------------------------------------------------- −65C to 150C
⚫ ESD susceptibility (Note3)
HBM (Human Body Mode)-------------------------------------------------------------------------------- 2KV
MM (Machine Mode)--------------------------------------------------------------------------------------- 200V
CDM (Charged-Device Model)--------------------------------------------------------------------------- 1KV

Recommended Operating Conditions (Note4)

⚫ Supply Input Voltage, VIN --------------------------------------------------------------------- +2.5V to +5.5V
⚫ Junction Temperature -------------------------------------------------------------------------- −40C to 125C
⚫ Ambient Temperature ---------------------------------------------------------------------------- −40C to 85C

2023/06/08
A.10 2
 EM5203J/AJ
Electrical Characteristics
VIN=5V, TA=25℃, unless otherwise specified
Parameter Symbol Test Conditions Min Typ Max Units
Supply Input Section
POR Threshold VPORTH - 2.2 2.5 V
Quiescent Current IQ IOUT=0A - 65 95 uA
Shutdown Current ISD EN#=5V - 0.1 1 uA
Output Voltage
On Resistance RON IOUT=0.5A - 60 80 m
Reverse Leakage Current IRev VOUT=5V , VIN=0V - 0.1 2 uA
Rising from 10% to 90%
Soft-Start Time - 1.5 2 ms
CL =1uF；RLOAD =10
Enable
Enable High Level VEN 1.2 - - V
Disable Low Level VSD - - 0.5 V
EN Input Current IEN - 0.1 1 uA
OC# Flag Output
OC# Output Resistance RFLGB ISINK=1mA - 20 80 
OC# Off Current IFLGB_OFF VFLGB=5V - 0.1 1 uA
OC# Delay Time TD 8 15 22 ms
OUT Shutdown Discharge
RDIS 100 
Resistance
Protection
OCP Threshold Level IOCP 2.4 3.2 4.2 A
Output Short Circuit Current ISC 1.2 1.7 3.1 A
o
Thermal Shutdown Temperature TSD - 160 - C
o
Thermal Shutdown Hysteresis TSDHYS - 30 - C
Output Reverse Voltage Protection
Output Reverse Voltage
RVP VOUT – VIN (internal spec) 100 200 mV
Protection
Recovery Voltage ROV VIN – VOUT (internal spec) 0 +60 mV
Recovery Voltage for FT VIN – VOUT (FT spec) -10 +60 mV
De-bounce time (internal spec) 9 us
Note 1. Stresses listed as the above “Absolute Maximum Ratings” may cause permanent damage to the device.
These are for stress ratings. Functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may remain possibility to affect device reliability.
Note 2. JA is measured in the natural convection at TA=25oC on a low effective thermal conductivity test board (Single layout,
1S) of JEDEC 51-3 thermal measurement standard.
Note 3. Devices are ESD sensitive. Handling precaution is recommended.
Note 4. The device is not guaranteed to function outside its operating conditions.
Note 5. EMC will review datasheet by quarter, and update new version.

2023/06/08
A.10 3
 EM5203J/AJ
Typical Operating Characteristics
Turn on from VIN# Turn off from VIN#
CH1: VIN, CH2:Vo, CH3:OC# CH1: VIN, CH2:Vo, CH3:OC#

Reverse Voltage Protection Short then power on into OT cycle

CH1:VIN, CH2:Vo, CH3: OC# ,CH4:IREV CH1:VIN, CH2:Vo, CH3:OC#

Fault Signal delay time Fault Signal during OTP occurs

CH1:VIN, CH2:VO, CH3:OC#,CH4:Io CH1:Vo, CH2:OC#, CH4:Io

2023/06/08
A.10 4
 EM5203J/AJ
Typical Operating Characteristics
2uS Response for Output short Protection Normal operating 2A output current
CH1:VIN, CH2:Vo, CH3:OC#, CH4: IO CH1:Vo, CH2:Fault, CH4:Io

RON Performance VS Temperature Shutdown current VS Input Voltage

UVLO ON Voltage VS Temperature Enable Voltage VS Temperature

2023/06/08
A.10 5
 EM5203J/AJ
Ordering & Marking Information
Device Name: EM5203AJ-20 for SOT-23-5

K2: Device Code, K2 for EM5203AJ-20

K2YWW YWW: Date Code

#1
Device Name: EM5203J-20 for SOT-23-5

K1: Device Code, K1 for EM5203J-20

K1YWW YWW: Date Code

#1

Outline Drawing

B1 B

e G

A
F

b
A1

Dimension in mm
Dimension A A1 B B1 b C D e F G
Min. 0.90 0.00 0.30 0.08 0.30
Typ. 1.15 2.80 1.60 2.90 0.95 0.45
Max. 1.30 0.15 0.50 0.22 1.45 0.60

2023/06/08
A.10 6
 EM5203J/AJ
Recommended minimum pads

1.9
1
1.6

3.6
0.95 0.7
2.6

2023/06/08
A.10 7
 EM5203J/AJ
◆ Tape&Reel Information:3000pcs/Reel(Dimension in millimeter)
P2

D0

W
P1 KO
R
Package SOT23-5
Reel Dimensions 7”
Pin1 Orientation
R1

Dimension in mm

Carrier tape Reel

Dimension
D0 K0 P1 P2 W R R1
Typ. 1.53 1.40 4.00 2.00 8.00 8.50 178.00
± 0.20 0.30 0.20 0.20 0.50 REF REF

2023/06/08
A.10 8