RS Part No. 696-1204 RS Part No.
696-1204
DIGITAL COLOUR VARIFOCAL IR LED CAMERA
SCI535HV
CAUTION
Do not open or strike this equipment. Sensitive electronics inside are vulnerable to excessive shock.
Instruction Manual • Do not install the equipment near any naked flames or heat sources. Excessive heat could damage this unit.
Digital Colour IR Camera
• Do not cover cloth or to install this unit in poorly ventilated places. This may lead to overheating.
• Do not continue to operate if there appears to be fault.
If the unit ceases to function, contact qualified service personnel for help.
SCI 535HV
• Do not touch the power connection with wet hands. Risk of short circuit or electric shock.
• Do not damage the power cord or leave it under pressure. Risk of fire or shock circuit.
FEATURE
1/3" COLOUR SONY SUPER HAD
HIGH RESOLUTION (68 , 36LEDs)
550TV Line
Minimum Illumination : 0.1Lux (f:1.2)
Auto White Balance
Automatic Gain Control
Dimension(mm) : 68 , 36LEDs
Power Source : DC12V ( 10%)
DC IRIS Vari-Focal Lens Type
SPECIFICATION SCI535HV (NTSC) SCI535HV (PAL)
Image Device 1/3" Colour SONY Super HAD CCD
Picture Elemtents 768(H) 494(V) 752(H) 582(V)
Scanning System 525 Lines, 2:1 Interlace 625 Lines, 2:1 Interlace
Sync System Internal Synchronization
Horizontal Resolution 550 TV Line
Video Output 1Vp-p 75
S/N Ratio More Than 50dB (AGC Off)
Gamma Characteristic 0.45
Gain Control 4dB ~ 30dB Auto
White Balance Auto 2100 K ~ 9100 K (Push Lock)
Electronic Shutter 1/60~1/100,000sec (Auto) 1/50~1/100,000sec (Auto)
LENS Auto Iris 4mm~9mm Varifocal lens
Smear Effect 0.005%
Minimum Illumination 0.1Lux (f:1.2)
Power Consumption 12V 10% DC, 400mA (IR ON)
Operation Temperature 10 ~ 50 , RH95% Max (14 F~122 F)
Storage Temperature 20 ~ 60 , RH95% Max
Weight Approx g
Housing ALUMINUM
Dimension(mm) 68 , 36LEDs
Cable(option) Standard 1000mm BNC/DC Jack
RS PART No.:696-1204
OWNER’S MANUAL OWNER’S MANUAL
How to use Bullet camera How to use CCTV camera
SCI535HV
Production composition & Parts Names
** Before installing or adjusting please read installation
guide that accompany with this product. Failure to follow
warning notices and instructions may result in property
Installation & connection
1)Locate installation area. Select area where it holds camera’s
damage. Improper installation and/or operation will void the
weight for long time.
warranty.
2)Please note the front direction shall be headed toward the
Before Using or Installing surveillance area. As the bracket is 2 axis adjustable, fix bracket
Please do not make any attempt to disassemble the camera. with its station screws to consider the surveillance area.
To avoid any electrical shock, Please do not remove camera cover & 3)It’s a varifocal lens 4~9mm. You can open the back cap and pull
screw. the inside compounds. Then you can adjust W(wide) > T(Tele)
Please consult with Installation specialist since there is no user & N(Near) > (Far) to turn to the arrow indication around the
execution. lens. After focusing, please close the dome cover.
Please do not use strong chemicals or detergent. 4)Connect power jack(Red cable) with DC12V and Video jack(yellow)
Use dry towel to wipe off the camera, to clean off the stain use weak to monitor or to DVR whichever is available
Cleaning detergent. 5)IR LEDs turns on automatically at low illumination. As well, the
Before operation please check the temperature, humidity, and level of color changes to Black/White
the power.
Please operate camera between temperature levels of -10 ~ 50 .
Please do not disclose the camera, if there is lot of smoke or gas.
Please do not disclose the camera under direct sunlight.
Do not aim camera directly at bright object.
By doing so, this action will cause blooming or smear.
Please handle camera with care.
Do not put camera near fire, as this may cause fire.
Please do not hit, or shake the camera.
This could cause camera to malfunction.
Improper care or use of the camera could damage the camera. Trouble Shooting
Please do not make children handle or operate camera. It may If you are not able to view anything from the screen.
cause children’s accidents or camera’s malfunction. Check power, video, strength of signal.
How to Use &Installations & Warnings Check monitor input/output.
Use of DC12V. ( Please use Adapter 500mA for DC12V). Check camera connection number with monitor.
Please use dry towel to clean camera instead of the abrasive. For Fuzzy Screen
(This could bring low quality screen view of camera) Check camera lens for dust or dirt. If so wipe them
Please do not misplace the camera. And prevent any malfunction. off with dry towel or brush.
Please do not use camera in humid or wet area. Check cover to see if it’s clean. If so wipe them off with dry towel or
Do not disclose camera to direct sunlight brush.
Do not expose camera to massive electric wave. Check for direct sunlight exposure towards camera.
Do not install camera location with lot of vibration. Check if protection film from camera cover is removed
Do not install product near very high temperature or very low For Dark Screen
temperature area. (Please refer to our operation manual on Check for Monitor Brightness.
operation temperature & storage temperature) Unbalanced Black & White on the Monitor.
Do not attempt to open dome cover after installation and -Check Monitor
image adjustment -Adjust the cameras position or angle of lens when screen is bright
If problem still remains please contact our Technical
Support Department.
