Programme Name SY B.
Tech Electronics,Sem-IV
Course Code R5EL2008L
Course Title Analog Integrated Circuits Lab
Faculty Name Prof. Sheetal Mudganti
Sr.N Experiment Name Date Sign
o
1 Inverting amplifier using Operational Amplifier
IC 741
2 Non-Inverting amplifier using Operational
Amplifier IC 741
3 Summing amplifier using Op-Amp IC 741
4 Difference amplifier using Op-Amp IC 741
5 Monostable Multivibrator using IC 555
6 Astable Multivibratoor using IC 555
Exp
No:1 Inverting Amplifier using Operational Amplifier IC 741
Aim: To design and setup an inverting amplifier circuit with OP AMP 741C for
a gain of 10,plot the waveforms, observe the phase reversal, measure the gain.
Objectives: After completion of this experiment, student will be able to design
and setup an inverting amplifier using OP AMP. He/she will be able to design
and implement OPAMP inverting amplifier circuit.
Equipments/Components:
Sr No. Name and Specification Quantity required
1 Dual power supply +/- 15V 1
2 Function generator (0 - 1
1MHz)
3 Oscilloscope 1
4 Bread board 1
5 IC 741C 1
6 Resistors 2
7 Probes and connecting wires As required
8 Multimeter 1
Principle:
It is a closed loop mode application of opamp and employs negative feedback.
The Rf and Ri are the feedback and input resistance of the circuit respectively.
The input terminals of the opamp draws no current because of the large
differential input impedance. The potential difference across the input terminals
of an opamp is zero because of the large open loop gain.
Due to these two conditions, the inverting terminal is at virtual ground potential.
So the current flowing through Ri and Rf are the same.
Ii = If
That is Vin/Ri = - Vo /Rf
Therefore Vo/Vin = Av = - Rf/ Ri,
Here the negative sign indicates that the output will be an amplified wave with
1800 phase shift (inverted output). By varying the Rf or Ri, the gain of the
amplifier can be varied to any desired value.
Procedure:
1. Check the components.
2. Check the resistant values using multimeter.
3. Setup the circuit on the breadboard and check the connections.
4. Switch on the power supply.
5. Give 1 Vpp / 1 KHz sine wave as input.
6. Observe input and output on the two channels of the oscilloscope
simultaneously.
7. Note down and draw the input and output waveforms on the graph.
8. Verify the input and output waveforms are out of phase.
9. Verify the obtained gain is same as designed value of gain.
10.Do the experiment on multisim.
Circuit Diagram:
Design:
Gain of an inverting amplifier Av = Vo/Vin = - Rf / Ri
The required gain = 10,
That is Av = - Rf/ Ri = 10
Let Ri = 1KΩ, Then Rf = 10KΩ
Observations:
Vin = ____Vpp Vo=____
Gain, Av = Vo/Vin
Graph:
Result:
Observed Gain Calculated Gain Graphical Gain
Conclusion:
Thus inverting gain of an operational amplifier studied.
Exp
No:2 Non-Inverting Amplifier using Operational Amplifier IC741
Aim: To design and setup an non-inverting amplifier circuit with OP AMP
741C for a gain of 10, plot the waveforms, observe the phase reversal, measure
the gain.
Objectives: After completion of this experiment, student will be able to design
and setup a non-inverting amplifier using OP AMP. He/she will be able to
design and implement OPAMP non-inverting amplifier circuit.
Equipments/Components:
Sr No. Name and Specification Quantity required
1 Dual power supply +/- 15V 1
2 Function generator (0 - 1
1MHz)
3 Oscilloscope 1
4 Bread board 1
5 IC 741C 1
6 Resistors 2
7 Probes and connecting wires As required
8 Multimeter 1
Principle:
It is a closed loop mode application of opamp and employs negative feedback.
The Rf and Ri are the feedback and input resistance of the circuit respectively.
The input terminals of the opamp draws no current because of the large
differential input impedance. The potential difference across the input terminals
of an opamp is zero because of the large open loop gain.
Due to these two conditions, the inverting terminal is at virtual ground potential.
So the current flowing through Ri and Rf are the same.
Ii = = 1 + =Av
By varying the Rf or Ri, the gain of the amplifier can be varied to any desired
value.
Procedure:
1. Check the components.
2. Check the resistant values using multimeter.
3. Setup the circuit on the breadboard and check the connections.
4. Switch on the power supply.
5. Give 1 Vpp / 1 KHz sine wave as input.
6. Observe input and output on the two channels of the oscilloscope
simultaneously.
7. Note down and draw the input and output waveforms on the graph.
8. Verify the input and output waveforms are out of phase.
9. Verify the obtained gain is same as designed value of gain.
10.Do the experiment on multisim.
Circuit Diagram:
Design:
Gain of an non-inverting amplifier Av =1 +
Let Ri = 1KΩ, Then Rf = 10KΩ
The calculated Gain= Av =
Observations:
Vin = ____Vpp Vo=____
Observed Gain, Av = 1 +
Graph:
Result:
Observed Gain Calculated Gain Graphical Gain
Conclusion:
Thus non-inverting gain of an operational amplifier studied.
Exp No 3 Summing amplifier using Op-Amp IC 741
Aim: To design and setup a summing amplifier circuit with OP AMP 741C for
a gain of 2 and verify the output.
Objectives: After completion of this experiment, student will be able to design
and setup a summing amplifier using OP AMP.
Equipment/Components:
Sr No. Name and Specification Quantity required
1 Dual power supply +/- 15V 1
2 DC power Supply 1
3 Multimeter 1
4 Bread board 1
5 IC 741C 1
6 Resistors 3
7 Probes and connecting wires As required
8 DSO 1
Principle:
Op-amp can be used to design a circuit whose output is the sum of several input
signals. Such a circuit is called a summing amplifier or an adder. Summing
amplifier can be classified as inverting & non-inverting summer depending on
the input applied to inverting & non-inverting terminals respectively. Circuit
Diagram shows an inverting summing amplifier with 2 inputs. Here the output
will be amplified version of the sum of the two input voltages with 180 phase
reversal.
Vo = - ( Rf/ Ri )(V1+V2)
Procedure:
Connections are made as in the circuit diagram. Apply input voltage V1
and V2 from the DC regulated power supply. +ve of V1 is connected to pin
2 of IC 741 through resistance R1 and +ve of V2 is connected to pin 2 of IC
741 through resistance R2. –ve of V1 and V2 are connected to ground. Pin 3
is grounded. +5 V of DC fixed power supply (+5 -0- -5) connected to pin 7
and -5 V is connected to pin 4. 0 of DC fixed power supply should be
connected to ground without fail. Note down the output voltage across pin 6
using multimeter (negative of the multimeter is connected to ground).
Repeat the experiment for different input voltages. Tabulate the readings in
the tabular column. Verify the output voltage with theoretical formula.
Circuit Diagram:
Design:
RF = RIN = 1KΩ
RIN = R1 & R2
Observations:
V1 V2 Vo Vo
Experimental Theoretical
Formula used:
Vo= - (V1+V2)
Since = = 1KΩ
Vo = - (V1+V2)
.
Conclusion: Studied Op-Amp as summing amplifier.
Exp No 4 Difference amplifier using Op-Amp IC 741
Aim: To design and setup a difference amplifier circuit with OPAMP IC 741C
for a gain of 2 and verify the output.
Objectives: After completion of this experiment, student will be able to design
and setup a difference amplifier using OP AMP.
Equipments/Components:
Sr No. Name and Specification Quantity required
1 Dual power supply +/- 15V 1
2 DC power Supply 1
3 Multimeter 1
4 Bread board 1
5 IC 741C 1
6 Resistors 3
7 Probes and connecting wires As required
8 DSO 1
Principle:
A difference amplifier is a circuit that gives the amplified version of the
difference of the two inputs, Vo =A(V1-V2), Where V1 and V2 are the inputs
and A is the voltage gain. Here input voltage V1 is connected to non-inverting
terminal and V2 to the inverting terminal. This is also called as differential
amplifier. Output of a differential amplifier can be determined using super
position theorem.
When V1=0,
The circuit becomes an inverting amplifier with input V2 and the resulting
output is V02= -Rf /Ri (V2).
When V2=0,
The circuit become a non-inverting amplifier with input V1 and the resulting
output is
V01= Rf/Ri(V1).
Therefore the resulting output according to super position theorem is
Vo = V01+ V02 = Rf/Ri(V1-V2)
Procedure:
Connections are made as in the circuit diagram. Apply input voltage V1 and V2
from the DC regulated power supply. +ve of V1 is connected to pin 2 of IC 741
through resistance R1 and +ve of V2 is connected to pin 3 of IC 741 through
resistance R2. –ve of V1 and V2 are connected to ground. Pin 3 is grounded
through resistance R4. Resistance R3 is connected between pin 2 and 6. +5 V of
DC fixed power supply (+5 -0- -5) connected to pin 7 and -5 V is connected to
pin 4. 0 of DC fixed power supply should be connected to ground without fail.
Note down the output voltage across pin 6 using multimeter (negative of the
multimeter is connected to ground). Repeat the experiment for different input
voltages. Tabulate the readings in the tabular column. Verify the output voltage
with theoretical formula.
Circuit Diagram:
Formula used:
Vo= − 𝑉1 + 𝑉2()()
When resistors R1 = R2 and R3 = R4
Vo = (𝑉2−𝑉1)
Since R1 = R2 = R3 = R4 =1KΩ
Vo = (V2 - V1)
Result:
V1 V2 Vo Vo
Experimental Theoretical
Conclusion: Studied Op-amp as difference amplifier.
Exp No 5 Monostable multivibrator using IC 555
Aim: To design and construct a monostable multivibrator using 555 IC and Plot
the output waveform.
Objectives: Upon completion of this experiment the students are able to design
and setup monostable multivibrator using IC 555.
Equipment/Components:
Sr No. Name and Specification Quantity required
1 Dual power supply 5V 1
2 Resistors 2
3 Capacitor 0.01μF ,0.1 μF 1each
4 Bread board 1
5 IC 555 1
6 Function generator 0 – 1MHz 1
7 Probes and connecting wires As required
8 DSO 1
Principle:
The monostable multivibrator has one stable state and one quasi stable state.
Monostable multivibrator produces an output pulse with defined time period for
each external trigger pulse applied. It comes out of the stable state only by use
of an external signal called trigger.
When the output is low, that is, the circuit is in stable state. Upon application of
trigger pulse to pin 2, the output of the comparator II becomes high which sets
the flip flop high. As the output is high, the transistor becomes OFF since it is
connected to the of the flip flop. Capacitor starts to charge through R towards
VCC, as soon as the capacitor voltage crosses 2/3 VCC (threshold voltage) the
output of the comparator I becomes high so the flipflop will reset and out goes
to low. At the same time transistor turns ON and hence capacitor rapidly
discharges through the transistor. The output of this circuit remains low until a
trigger pulse is again applied. The time during which the output remains high is
given by
T = 1.1 RC.
Procedure
1. Check the components.
2. Setup the monostable multivibrator circuit on the breadboard and check
the connections.
3. Switch on the power supply.
4. Put the function generator output to square wave mode. Adjust the
amplitude to 5V.
5. Observe trigger input , output and capacitor voltage on different channels
of the oscilloscope simultaneously.
6. Draw the waveforms on the graph.
Circuit Diagram:
Design:
Time period T = 1.1RC
Let T = 1ms ; C = 0.1μF
R = 1 x / (1.1 x 0.1 x )
R = 9.09 xΩ = 10KΩ (std)
For triggering circuit
RdCd = 0.016t
Let t = 3ms, and Cd = 0.01 μF ; then Rd = 4.7KΩ
Observed Graph:
Conclusion:
Exp No 6 Astable multivibrator using IC 555
Aim: To study the Frequency Response of Astable Multivibrator.
Objectives: Upon completion of this experiment the students are able to design
and setup monostable multivibrator using IC 555.
Equipment/Components:
Sr No. Name and Specification Quantity required
1 Dual power supply 5V 1
2 Resistors 2
3 Capacitor 0.01μF ,0.1 μF 1each
4 Bread board 1
5 IC 555 1
6 Function generator 0 – 1MHz 1
7 Probes and connecting wires As required
8 DSO 1
Principle: The 555 timer is a highly stable device for generating accurate time
delay. The internal structure of 555 is shown in which there are two
comparators, a flip flop, an output stage, a voltage divider network and a
transistor. The comparator is a device whose output is high when the non-
inverting input voltage is greater than inverting input voltage and output is low
when inverting input voltage is greater than non-inverting input voltage. The
voltage divider network consists of three 5KΩ resistors and provides a trigger
voltage level of 1/3VCC
and threshold voltage level of 2/3VCC.The control voltage is used for changing
the threshold and trigger voltages externally.
555 as Astable multivibrator: Astable multivibrator means it has no stable
states. It has two quasi stable states (high and low). In the figure given, there are
2 external resistors RA and RB and a capacitor C. When the power is given to
the circuit the capacitor C will charge towards VCC through RA and RB, when
the capacitor voltage exceeds the level of 2/3VCC (threshold voltage) the output
of the comparator I goes high which resets the flip flop so the output Q of the
flip-flop becomes low and becomes high. Now the transistor which is connected
to becomes ON. The capacitor C started to discharge through RB and transistor
exponentially.When voltage across capacitor reaches just below of 1/3VCC
(trigger voltage) the output of the comparator II becomes high and sets the flip
flop, turning OFF the transistor since it is connected to the of the flip flop. The
capacitor C will begin to charge towards VCC through RA and RB. when the
capacitor voltage exceeds the level of 2/3VCC, the output of the comparator I
goes high which resets the flip-flop so the output Q of the flip flop becomes low
and becomes high. The cycle continues which gives a square wave at the output
(pin 3) and charging and discharging wave form across capacitor (pin 2&6).
Procedure:
1. Connections are made as in the circuit diagram.
2. Connect CRO lead across pin no.3 of 555and ground point as shown in
the circuit diagram.
3. Switch on the instrument using ON/OFF toggle switch provide on the
front panel and also switch ON the CRO.
4. Observe the square wave output on CRO.
5. Calculate the frequency of output signal using formula 𝑓=1.44/(+2)𝐶1
Circuit Diagram:
Graph:
Conclusion: The Frequency Response of Astable Multivibrator is studied.
