UltraCella

Electronic control for Cold Rooms

User manual

NO POWER
& SIGNAL
CABLES
TOGETHER
READ CAREFULLY IN THE TEXT!

H i g h E f f i c i e n c y S o l u t i o n s
 ENG
WARNING DISPOSAL

CAREL developed its products thanks to the several years of experience in the INFORMATION FOR THE USERS REGARDING THE CORRECT HANDLING OF
HVAC field, continuous investment in technological innovation of the product, WASTE ELECTRIC AND ELECTRONIC EQUIPMENT (WEEE)
rigorous quality procedures and processes with in-circuit and function tests on
100% of its production, as well as the most innovative production technologies With reference to European Parliament and Council Directive 2002/96/EC issued
available on the market. CAREL and its branch offices/affiliates do not guarantee, on 27 January 2003 and the related national implementation legislation, please
in any case, that all the aspects of the product and the software included in the note that:
product will respond to the demands of the final application, even if the product is • WEEE cannot be disposed of as municipal waste, said waste must be collected
built according to state-of-the-art techniques. separately;
The client (builder, developer or installer of the final equipment) assumes every • the public or private waste collection systems defined by local legislation must
responsibility and risk relating to the configuration of the product in order to reach be used. Moreover, the equipment can be returned to the distributor at the end
the expected results in relation to the specific final installation and/or equipment. of its working life when buying new equipment;
CAREL, in this case, through specific agreements, can intervene as consultant for • this equipment may contain dangerous substances: improper use or incorrect
the positive result of the final start-up machine/application, but in no case can it be disposal of such may have negative effects on human health and on the
held responsible for the positive working of the final equipment/apparatus. environment;
• the symbol (crossed-out wheeley bin) shown on the product or on the
The CAREL product is a state-of-the-art product, whose operation is specified in the packaging and on the instruction sheet indicates that the equipment has been
technical documentation supplied with the product or can be downloaded, even introduced onto the market after 13 August 2005 and that it must be disposed
prior to purchase, from the website www.carel.com. of separately;
Each CAREL product, in relation to its advanced technological level, needs a phase • in the event of illegal disposal of electrical and electronic waste, the penalties are
of definition / configuration / programming / commissioning so that it can function specified by local waste disposal legislation.
at its best for the specific application. The lack of such phase of study, as indicated
in the manual, can cause the final product to malfunction of which CAREL cannot Materials warranty: 2 years (from the date of production, excluding consumables).
be held responsible.
Only qualified personnel can install or carry out technical assistance interventions Type-approval: the quality and safety of CAREL S.P.A. products are guaranteed by
on the product. the design system and ISO 9001 certified production.
The final client must use the product only in the manner described in the
documentation related to the product itself.

Without excluding proper compliance with further warnings present in the manual,
it is stressed that in any case it is necessary, for each CAREL product:
• Not allow the electronic circuits getting wet. Rain, humidity and all types of HACCP: CAUTION
liquids or condensate contain corrosive mineral substances that can damage
the electrical circuits. In any case, the product should be used and stored in
environments that respect the temperature and humidity limits specified in the
manual;
• Not to install the device in a particularly hot environments. Temperatures that
are too high can shorten the duration of the electronic devices, damaging them
and distorting or melting the parts in plastic. In any case, the product should be
The Food Safety programs based on HACCP procedures and on certain national
used and stored in environments that respect the temperature and humidity
standards, require that the devices used for food preservation are periodically
limits specified in the manual;
checked to make sure that the measuring errors are within the allowed limits of
• Not to try to open the device in any way different than that indicated in the the application of use.
manual;
• Not to drop, hit or shake the device, because the internal circuits and Carel recommends compliance with the indications of European standard
mechanisms could suffer irreparable damage.
“Temperature recorders and thermometers for transport, storage and distribution
• Not to use corrosive chemical products, aggressive solvents or detergents to of chilled, frozen, deep-frozen/ quick-frozen food and ice cream – PERIODIC
clean the device;
VERIFICATION “, EN 13486 -2001 (or subsequent updates)or similar standards and
• Not to use the product in application environments different than those prescriptions applicable in the country of use.
specified in the technical manual.
The manual contains further indications regarding technical feature, proper
All the above reported suggestions are also valid for the control, serial boards, installation and configuration of the product.
programming keys or however for any other accessory in the CAREL product
portfolio.
CAREL adopts a continuous development policy. Therefore, CAREL reserves the
right to carry out modifications and improvements on any product described in
this document without prior notice.

The technical data in the manual can undergo modifications without forewarning.
NO POWER
The liability of CAREL in relation to its products is specified in the CAREL general & SIGNAL
CABLES
contract conditions, available on the website www.carel.com and/or by specific
TOGETHER
agreements with customers; specifically, to the extent where allowed by applicable
legislation, in no case will CAREL, its employees or subsidiaries be liable for any READ CAREFULLY IN THE TEXT!
lost earnings or sales, losses of data and information, costs of replacement
goods or services, damage to things or people, downtime or any direct, indirect, WARNING: separate the probe cables and the digital input cables as
incidental, actual, punitive, exemplary, special or consequential damage of any
much as possible from the inductive load and power cables to prevent
kind whatsoever, whether contractual, extra-contractual or due to negligence, or
possible electro-magnetic interference. Never introduce power cables
any other liabilities deriving from the installation, use or impossibility to use the
product, even if CAREL or its subsidiaries are warned of the possibility of such and signal cables (including those of electric control board) into the same
damage. cable troughs.

3 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

 ENG
Content
1. INTRODUCTION 7 6. CONTROL 44
1.1 Codes.................................................................................................................................7 6.1 Switching the controller ON and OFF .......................................................44
1.2 Expansion modules..................................................................................................8 6.2 Virtual probe...............................................................................................................44
6.3 Set point.......................................................................................................................44
2. INSTALLATION 9
6.4 Pump down................................................................................................................46
2.1 Assembly and sizes (mm)....................................................................................9 6.5 Autostart in pump down...................................................................................47
2.2 Structure.......................................................................................................................10 6.6 Continuous cycle.....................................................................................................47
2.3 Wiring diagram.........................................................................................................11 6.7 Door switch control...............................................................................................47
2.4 Expansion modules assembly.........................................................................12 6.8 Defrost............................................................................................................................48
2.5 Ultra EVD module....................................................................................................14 6.9 Evaporator Fans........................................................................................................50
2.6 Ultra Power module...............................................................................................15 6.10 Condenser fans.........................................................................................................51
2.7 EVDice............................................................................................................................16 6.11 Duty setting................................................................................................................53
2.8 Ultra 3ph module EVAPORATOR....................................................................16 6.12 Bowl resistance.........................................................................................................53
2.9 Ultra 3ph module FULL.......................................................................................17 6.13 Defrosting with 2 evaporators........................................................................53
2.10 Installation...................................................................................................................18 6.14 Second compressor with rotation................................................................54
2.11 Connection in supervisoring network.......................................................18 6.15 Control with dead band......................................................................................55
2.12 UltraCella Service terminal................................................................................19 6.16 AUX output activation by time band.........................................................55
2.13 Upload/download parameters (USB memory key)..........................19 6.17 Humidity management......................................................................................56
6.18 Generic functions....................................................................................................57
3. USER INTERFACE 20
3.1 Display............................................................................................................................20 7. PARAMETERS TABLE 61
3.2 Keyboard......................................................................................................................21
3.3 Programming.............................................................................................................22 8. SIGNALS AND ALARMS 70
3.4 Procedures...................................................................................................................24 8.1 Signalling......................................................................................................................70
3.5 Multifunction menu..............................................................................................26 8.2 Alarms............................................................................................................................70
3.6 Message language selection...........................................................................30 8.3 Reset alarms................................................................................................................70
8.4 HACCP alarms and display................................................................................70
4. COMMISSIONING 31
8.5 EVD EVO alarms........................................................................................................71
4.1 First commissioning..............................................................................................31 8.6 EVDice alarms............................................................................................................71
4.2 Parameters to be set for the commissioning.........................................31 8.7 3PH module alarms...............................................................................................72
4.3 Single digit display models cod. WB000S* commissioning..........31 8.8 Alarm parameters...................................................................................................73
4.4 Double digit display models cod. WB000D* commissioning......32 8.9 HACCP Alarm parameters and monitoring activation ..................74
4.5 Commissioning with UltraCella Service Terminal...............................33 8.10 High condenser temperature alarm ..........................................................74
4.6 Main function commissioning........................................................................33
4.7 Light management................................................................................................37 9. TECHNICAL SPECIFICATIONS 75
4.8 Other configuration parameters...................................................................37 9.1 UltraCella technical characteristics..............................................................75
4.9 Ultra EVD EVO module commissioning....................................................38 9.2 EVD Modules technical characteristics......................................................76
4.10 EVDice commissioning........................................................................................39 9.3 Power Modules technical characteristics.................................................76
4.11 Ultra 3Ph Evaporator module commissioning.....................................41 9.4 3PH EVAPORATOR Modules technical characteristics......................76
4.12 Ultra 3Ph Full module commissioning......................................................42 9.5 3PH FULL Modules technical characteristics.........................................77

5. OUTPUTS CONFIGURATION AND PROTECTIONS 43 10. ELECTRICAL WIRING 3PH MODULES 78

5.1 Analogue output.....................................................................................................43 10.1 Electrical wiring 3PH EVAPORATOR Module...........................................78
5.2 Digital Outputs.........................................................................................................43 10.2 Electrical wiring 3PH FULL Module..............................................................85

11. SOFTWARE RELEASE 93

11.1 Software release table..........................................................................................93

5 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

 ENG
1. INTRODUCTION
Ultracella is a family of products consisting of a control system for the The accessory modules allow:
basic functions of a cold room to which can be added further modules for • the installation of the electronic expansion valve, using the module
accessory functionalities (e.g. electronic valve, power relays, etc.). with CAREL EVD Evolution driver dedicated to the control of superheat;
• compressor control with power relay of up to 3 Hp;
The user interface ensures ease in use and it consists, depending on the • the use of a single-phase circuit breaker switch in addition to the
models, of: power relay.
• wide led display on which can be viewed the operating temperature
and the active loads;
• a graphic terminal with text strings in multiple languages, which
guide the user during commissioning (wizard). It is also equipped with
contextual help menus accessible during programming, that provide
an accurate description of the alarms.

The graphic terminal is also available as a “service tool”, which is useful

when the control has the only LED interface.

UltraCella has a port for the insertion of a USB memory key to:
• load the languages for the graphic terminal during the first UltraCella
commissioning;
• parameters upload/download;
• other operations reserved for the service centre (e.g. software update);
• download log of temperature recorded.

When mounting the optional modules are matched to the right of the
main control system and connected to it with watertight coupling, to Fig. 1.a
ensure the IP degree of protection of the assembly.

Main characteristics:
• 6 relay outputs: compressor, defrost, fan, light, AUX1, AUX2;
• assembly on guide DIN or wall;
• LED board with bright display with 3 digits, with decimal point and 1.1 Codes
icons that indicate the operating status; Codes Description
• integration of the keys in the front panel (LED board) to ensure a high WB000S**F0 UltraCella, led display with single row
degree of protection (IP65) and safety during operation and cleaning; WB000D**F0 UltraCella, led display with double row
• availability of 10 sets of parameters (recipes) preloaded by CAREL Tab. 1.a
but modifiable, corresponding to the same number of parameters
configurations, to adapt the control to the specific conservation needs
required by the cold room;
• navigation on intuitive user interface with contextual backlight
keyboard;
• defrost can be driven using the keyboard, digital input and supervisor;
• various types of defrost managements, on one or two evaporators:
natural (with stop compressor), resistance, hot gas;
• control of compressors with up to 2 Hp or up to 3 Hp with the
accessory power module;
• temperature control with virtual adjustment probe;
• digital inputs that can be configurated for alarm activation, enabling or
activating defrost, door switch, auxiliary output, on / off, etc;
• control of 1 compressor with double step or of two compressors, even
with rotation;
• keyboard safety: operation of the single keys can be disabled to avoid
tampering;
• light management by door switch or dedicated key;
• alarm buzzer; Fig. 1.b Fig. 1.c
• HACCP function: temperature monitoring and adjustment in case of
alarm due to high temperature during operation or after black out;
• RS485 network connection for remote monitoring and supervision
sytems.

7 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
1.2 Expansion modules
EVD Module (cod. WM00E***00)
Expansion module containing the supply transformer and the driver EVD
Evo to control the electronic expansion valve.

Codes Description
WM00ENS000 Ultra EVD Module without EVD display
WM00ENSI00 Ultra EVD Module with EVD I/E display
WM00ENNI00 Ultra EVD Module “blind” - commissioning through UltraCella
Tab. 1.b

Fig. 1.g

Three phases expansion Modules

Ultra 3PH Evaporator Modules are expansion modules to control three-
phase evaporators. They have to be combined with UltraCella controls
P/Ns WB000S% or WB000D% and have inside high power actuators to
handle directly three-phase loads of the evaporator.

Ultra 3PH Full Modules are expansion modules to control three-phase

condensing and evaporator units. They have to be combined with
UltraCella controls P/Ns WB000S% or WB000D% and have inside high
power actuators to handle directly three-phase loads of the condensing
and evaporator units.
Code Description
WT00E600N0 Ultra 3PH module Evaporator 6kW
WT00E900N0 Ultra 3PH module Evaporator 9kW
Fig. 1.d Fig. 1.e
WT00F4B0N0 Ultra 3PH module Full 4HP
WT00F7C0N0 Ultra 3PH module Full 7,5Hp
Tab. 1.d

Fig. 1.h Fig. 1.i

UltraCella Service Terminal

The UltraCella control can be connected to an external terminal, without
Fig. 1.f having to open the unit, for easy commissioning and programming of
the control parameters, to be used with the controls having LED display.
When connecting the UltraCella Service Terminal the LED interface is
Power module (cod. WM00P000*N)
temporarily disabled.
Expansion module that contains the circuit breaker switch and 3 Hp relay
Code Description
for compressor control. There is also a version without relay, to give way
PGDEWB0FZ0 UltraCella Service with pGD1 user interface
to the installer to insert devices suitable for the application (contactors, PGDEWB0FZK UltraCella Service with pGD1 user interface + 3 m.
safety devices, etc.) cable and S90CONN001 connector
Codes Description Tab. 1.e
WM00P0003N Ultra Power Module main switch and 3HP relay
WM00P000NN Ultra Power Module main switch
Tab. 1.c

Fig. 1.j

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 8

 ENG
2. INSTALLATION
2.1 Assembly and sizes (mm)
The control system has holes on the lower and right side, in which the
installer can insert the cable glands.

30 30

47,5

47,5
87,5

87,5
290

290

N N

107,5

107,5
47,5

47,5

32 32 62 62 62
200 200 100 100 380 380

Fig. 2.a Fig. 2.b

Mounting
A: with DIN rail B: without DIN rail
260

2
1

Ø 4,5
156
1.a: Fix the DIN rail and insert the controller 1.b: Make 4 holes (Ø 4,5 mm) according to the drilling
template and insert the dowels (mm)

1
1

2 1 2
2 2
1 1

2
1

1
2
1 2
1
1
2.a: Remove the frames, loosen the screws (1) and open the panel 2.b: Remove the frames

9 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG

A A
1
2
1

2
1

B N
1
2

1 2

B A A

3.a: Mark on the wall the positions of the lower holes, 3.b: Fasten the screws (1) and fix the panel. Loosen the screws (2) and open the panel.
remove the panel and perform the drills (Ø 4.5 mm); insert
the plugs. Replace the panel on the DIN guide and fix it
fastening the lower screws.

1
2

connection
N
to option
modules

power supply, compressor probes,

fan, actuators digital inputs

4: Use the holes and mount the cable glands to connect:

• on the lower side: supply cables, probes, actuators;
• on the right side: cables for the connection of accessory Caution: separate the power cables (supply, actuators) from the signal cables
modules; (probes, digital inputs).
5: Close the panel fastening the screws (2).
Note: use a hole saw to drill the knock-outs (A).

2.2 Structure
Models with single digit display cod. WB000S*
3 4 3

Key
1 Keyboard
2 Display
3 Wall mounting holes
4 Locking screws
5 Connector for UltraCella Service (*)
6 Green LED (*)
7 Red LED (*)
3 8 7 6 5 4 3 8 USB Port (*)
(*) Visible after removing the bottom frame
Fig. 2.c

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 10

 ENG
Models with double digit display cod. WB000D*
3 4 3

Key
1 Keyboard
2 Display
3 Wall mounting holes
4 Locking screws
5 Connector for UltraCella Service (*)
6 Green LED (*)
7 Red LED (*)
8 USB port (*)
3 8 7 6 5 4 3
(*) Visible after removing the bottom frame
Fig. 2.d

2.3 Wiring diagram

to remote terminal display

Key
Rx/Tx+
Rx/Tx-

to LED display board

GND

GND
GND

B1…B5 Analogue inputs 1…5

VL

DI1 Door switch

48 47 46 45 44 43 30 B3 CAREL NTC, PT1000
DI2, DI3 Digital inputs 2, 3
31 29 B2 CAREL NTC, PT1000 Y1 0…10 V analogue output
32 28 B1 CAREL NTC, PT1000 GND Grounding for signals
33 27 Y1 analog output (0 to 10 Vdc) 5 VREF Ratiometric pressure
34 26 B4 CAREL NTC, analog input 0 to 10 Vdc
49 50 51 52 53 54 35 probe power supply
25 B5
36
GND
Rx/Tx-
Rx/Tx+
GND
Rx/Tx-
Rx/Tx+

GND 24 GND OUT B5 analog +Vdc Active probe supply

37 23 5 VREF 0 to 5 Vdc M input (humidity)
38 22 + Vdc +V (4 to 20 mA) CMP DO1 (*) Compressor
39 21 DI1
FieldBus BMS
DI1 DEF DO2 (*) Defrost
40 20 DI2
41 19 DI3 FAN DO3 (*) Evaporator fan
to graphic 42 Door switch LIGHT DO4 (*) Light
terminal display AUX1 DO5 (*) Auxiliary
output 1
18
24 Vac AUX2 DO6 (*) Auxiliary
17 output 2
UltraCella Control L, N Power Supply
Fieldbus Fieldbus Serial (19200
16
R6 Baud, 8 bit, 2 bit stop, no
R5 - R6 15 parity)
EN60730-1 12 (10) A BMS BMS Serial
250 V 14
UL 873 12 A res. 2HP R5 DEF
12FLA 72 LRA
(*) Digital outputs display in the
13
multifunction module (see chap. 3).
12
FAN
11
R3 - R4 R4
10 A res. 10
EN60730-1 5 (3) A LIGHT
250 V 9
UL 873 10 A res. 5FLA R3
18 LRA 8
R2
7
R1 - R2
EN60730-1 8 (4) A N.O. 6
to connector board

250 V
UL 873 8 A res. 2FLA 5
12 LRA R1
4
3

2
1
230 V
20 A max

Fig. 2.e

11 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
2.4 Expansion modules assembly
Dimensions (mm) Layout
30 30 If more than one expansion modules it is to assemble, use the
arrangement of figure to optimize the wiring.
47,5 47,5
87,5 UltraCella Control Power Module EVD Module

87,5
290

260
drilling template
107,5

107,5
Ø32 Ø32
Ø 4,5 1 2

47,5 47,5

128 110 101 103

WM00ENS000 WM00ENNI00
WM00ENSI00
Fig. 2.f
Fig. 2.h
Overall drilling template (mm)
If UltraCella and expansion modules have to be mounted at the same
time, use the overall drilling template.
33

DIN RAIL
43

UltraCella Expansion
260

Module
214

Ø 4,5 mm

156 24 103

Fig. 2.g

Mounting

1 3
A B

2 1
2

2
1

1
2

1: Use a hole saw to drill the panel in correspondence with the predrilled 2: Remove the faceplates. Unscrew the screws (3) and open the
holes (steps A, B). If present, fasten the DIN rail for the module. UltraCella control

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 12

 ENG

1 1
1 A A

B N

2
1 1
1 B A A

3: Raise the cover or remove the faceplates and unscrew the screws to 4: Put the module close to UltraCella control and insert the coupling
remove the panel and open the module. clamps supplied as standard.

13 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
2.5 Ultra EVD module
Mounting with DIN rail Mounting without DIN rail
5.a Mark the positions of the bottom holes on the wall (A), remove the 5.b Mark the positions of the 4 holes (A), remove the coupling clamps
coupling clamps (B), extract the module (C). Drill the corresponding holes (B), extract the module (C). Drill the corresponding holes (Ø 4,5 mm),
(Ø 4,5 mm) and insert the anchors. Place again the module: mount the depending on drilling template and insert the anchors. Place again the
coupling clamps (B) and fasten the screws (A). module: mount the coupling clamps (B) and fasten the screws (A).

B B A A
PRI 230 V PRI 230 V

B B N

COMA
NOA
1 3 2 4

G0
VBAT
G
N
COMA
NOA

1 3 2 4
G0
VBAT
G

SEC 24 V SEC 24 V
C C

VREF
GND

DI1
DI2
S1
GND

S4
S2
S3
Tx/Rx
VREF
GND

DI1
DI2
S1

GND
S4
S2
S3

Tx/Rx

B A A B A A

Fig. 2.i Fig. 2.j

WM00ENNI00: Connect UltraCella to EVD module by serial cable in according with following wiring diagram e refer to below parameters table about EVD
Evo driver commissioning.

WM00ENSI00 and WM00ENS000:

1. Driver commissioning by EVD Evo display.
Connect auxiliary UltraCella output AUX1 or AUX2 relay to digital input DI1 of EVD Evo and set parameters in this way:
• H1=7 (for AUX1) or H5=7 (for AUX2) -> second delayed compressor
• C11=0 -> delay activation second compressor = 0
In this way auxiliary output is set like free contact cooling request, suitable to be connected to digital input DI1 of EVD Evo driver. No setting is requested
in UltraCella.
2. EVD Evo driver commissioning by UltraCella
Connect UltraCella to EVD module by serial cable in according with following wiring diagram e refer to below parameters table about EVD Evo driver
commissioning. If its’ connected by serial cable, driver parameters can be displayed only (not modifiable) by local EVD Evo display.
Once driver is abled by UltraCella (parameter P1=1) its parameters are ones communicated and set by UltraCella, in according with below parameters
table (modifiable by UltraCella only); parameters eventually previously set by EVD Evo display will be lost.

ULTRACELLA CONTROL Fig. 2.k ULTRA EVD MODULE BLIND

cod. WM00ENNI00

CAREL
ExV
Rx/Tx+
Rx/Tx-
GND

GND
GND

bianco/white
VL

verde/green
48 47 46 45 44 43 30 B3 CAREL NTC, PT1000
31 29 B2 CAREL NTC, PT1000
marrone/brown
32 28 B1 CAREL NTC, PT1000 giallo/yellow
33 27 Y1 analog output (0 to 10 Vdc, PWM)
34 26 B4 CAREL NTC, analog input 0 to 10 Vdc
49 50 51 52 53 54 35 25 B5
36
GND
Rx/Tx-
Rx/Tx+
GND
Rx/Tx-
Rx/Tx+

GND 24 GND OUT B5 analog input

37 23 5 VREF 0 to 5 Vdc M (4 to 20 mA) shield S

38 22 + Vdc +V
39 21 DI1 DI1 (**) 24 Vac
FieldBus BMS 40 20 DI2
41 19 DI3
42 Door switch 2 AT
25 VA
COMA
NOA

1 3 2 4
G0
VBAT
G

18
24 Vac
17
UltraCella Control
16
R6 CMP
R5 - R6 15
EN60730-1 12 (10) A
250 V 14
UL 873 12 A res. 2HP R5 DEF
12FLA 72 LRA 13
12
FAN
11
R3 - R4 R4
10 A res. 10
EN60730-1 5 (3) A LIGHT
250 V 9
UL 873 10 A res. 5FLA R3
18 LRA 8
R2
7
VREF
GND

R1 - R2
DI1
DI2

GND Tx/Rx
S1
S2
S3
S4

EN60730-1 8 (4) A N.O. 6

250 V
UL 873 8 A res. 2FLA
12 LRA R1
5 EVD Module
4
ratiometric pressure
3 transducer

2
1
230 V
20 A max NTC

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 14

 ENG
2.6 Ultra Power module
Mounting with DIN rail
Mounting without DIN rail
5.a Mark the positions of the bottom holes (A), remove the coupling
clamps (B), extract the module (C). Drill the corresponding holes (Ø 4,5 5.b Mark on the wall the positions of the 4 holes (A), remove the coupling
mm) and insert the anchors. Place again the module: mount the coupling clamps (B), extract the module (C). Drill the corresponding holes (Ø 4,5
clamps (B) and fasten the screws (A). mm), depending on drilling template and insert the anchors Place again
the module: mount the coupling clamps (B) and fasten the screws (A).
B
A A
B

B N
C

2 3
B N
C
6 5
2 3

6 5

B A A
B A A
Fig. 2.l
Fig. 2.m

Connect electrically the mudule wiring according to the diagram.

ULTRACELLA CONTROL ULTRA POWER MODULE

Power
Module
Rx/Tx+
Rx/Tx-
GND

GND
GND
VL

48 47 46 45 44 43 CMP
30 B3 CAREL NTC, PT1000
31 29 B2 CAREL NTC, PT1000
32 28 B1 CAREL NTC, PT1000
33 230 V~
27 Y1 analog output (0 to 10 Vdc, PWM)
34 26 B4 L N
49 50 51 52 53 54 CAREL NTC, analog input 0 to 10 Vdc
35 25 B5
GND
Rx/Tx-
Rx/Tx+
GND
Rx/Tx-
Rx/Tx+

36 OUT B5 analog input

GND 24 GND
37 23 5 VREF 0 to 5 Vdc M (4 to 20 mA)
38 22 + Vdc +V
39 21 DI1 (**)
DI1
FieldBus BMS 40 20 DI2
41 19 DI3 1 2 PE
Circuit
to graphic 42 Door switch
Breaker
terminal display BROWN CYAN
18
24 Vac CYAN
17
UltraCella Control BROWN
RED
16 Relay 3Hp (*)
R6
R5 - R6 15
EN60730-1 12 (10) A CYAN
250 V 14
UL 873 12 A res. 2HP R5 DEF 6 3 2 3
12FLA 72 LRA 13
12

11
FAN 5 2 6 5
R3 - R4 R4
10 A res. 10
EN60730-1 5 (3) A LIGHT
250 V 9
UL 873 10 A res. 5FLA R3
18 LRA 8
R2
7
R1 - R2 2 3
EN60730-1 8 (4) A N.O. 6
250 V
UL 873 8 A res. 2FLA 5 6 5
12 LRA R1
to connector 4
board BROWN
3

2
1
230 V
20 A max (*) Note: highlighted wires and 3hp relay supplied with the module code
WM00P0003N
Fig. 2.n

15 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
2.7 EVDice
For details on assembling EVD ICE on the evaporator, see the user manual,
+0300037EN
Connect UltraCella to the EVD ICE driver via the Fieldbus serial line (RS485
Modbus protocol), as shown in the following wiring diagram, and refer to
the parameter table for the driver configuration

Rx/Tx+
Rx/Tx-
to LED display board
GND CAP

GND
GND
VL
48 47 46 45 44 43 30 B3 CAREL NTC, PT1000 Non rimuovere il cappuccio di
B
31 29 B2 CAREL NTC, PT1000 protezione!
ULTRACAP
32 28 B1 CAREL NTC, PT1000 Do not remove the protection cap!
Module
33
49 50 51 52 53 54
34
27
26
Y1
B4
analog output (0 to 10 Vdc, PWM)
CAREL NTC, analog input 0 to 10 Vdc
C D
35 25 B5
36
GND
Rx/Tx-
Rx/Tx+
GND
Rx/Tx-
Rx/Tx+

CAREL E2V / E3V

GND
37
24
23
GND
5 VREF 0 to 5 Vdc
OUT B5 analog
M input
unipolar valve A
38 22 + Vdc +V (4 to 20 mA)
39 21 DI1 DI1 (**)
BMS 40 20 DI2
to graphic FieldBus 41 19 DI3 Door switch
terminal 42

18
24 Vac
17 S2 S1

16
R6 CMP
R5 - R6 15
EN60730-1 12 (10) A
250 V 14
UL 873 12 A res. 2HP R5 DEF
GASType

12FLA 72 LRA 13 Mode

Super Heat

12
FAN
11
R3 - R4 R4
10 A res. 10
EN60730-1 5 (3) A LIGHT
250 V 9
UL 873 10 A res. 5FLA R3
18 LRA 8
R2
7
R1 - R2
EN60730-1 8 (4) A N.O. 6
250 V
to connector board

UL 873 8 A res. 2FLA 5

12 LRA R1
4
3
F E
verde/ green GND marrone / brown L
2 nero / black Tx / Rx- blu / blue N
bianco / white Tx / Rx+ nero / black DI
1
230 V
20 A max
380

shield

230 Vac
shield

Fig. 2.o

2.8 Ultra 3ph module EVAPORATOR

1. Following drilling template, drill 4 (6) holes on the wall: 130
452 Important:
• Unscrew 6 fixing screws of frontal cover
• Remove frontal cover 186• separate the power cable (power supply, actuators) from the signal
• Fix panel to the wall by using screws with suitable length to wall cables (probes, digital inputs) and serial cable
thickness • use cable with section suitable to current rating they have to carry
• Drill side surface of expansion module where it’s necessary and fit • connect clamp marked with PE to the ground of power supply system
cable glands to connect: power supply cables, serial cable, probes
and power cables for loads 2. Connect three-phase expansion to UltraCella by shielded serial cable
AWG 22
3. Close frontal by screwing the 6 screws
4. Power on UltraCella (230 Vac) and expansion three-phase module (400
Vac)
5. Activate magnetothermic switch.
290

160

300
Fig. 2.p

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 16

 to connector board

•
•
•
•
290 to connector board

Remove frontal cover

DEF

FAN
CMP

LIGHT
160

and power cables for loads

0 to 5Vdc
analog output (0 to 10 Vdc, PWM)
CAREL NTC, PT1000
CAREL NTC, PT1000
CAREL NTC, PT1000
2.9 Ultra 3ph module

B5

input
analog

Fig. 2.s
CAREL NTC, analog input 0 to 10 Vdc

(4 to 20 mA)
300
Fig. 2.r
DEF

FAN

Fig. 2.q
CMP

LIGHT
0 to 5Vdc

19 19

452FULL
analog output (0 to 10 Vdc, PWM)

1
condenser fan 1 MV3:1 101 XA1:103

M
Unscrew 6 fixing screws of frontal cover
18 18
CAREL NTC, PT1000
CAREL NTC, PT1000
CAREL NTC, PT1000

condenser fan 1 MV3:2 102 QF2:N2/XA1:106

P
19 19
B5

partialization pressure switch condenser fan SP1 103 XA1:101/KM3:14

input

20 20
analog

partialization pressure switch condenser fan SP1 104 XA1:105

20 20
CAREL NTC, analog input 0 to 10 Vdc

(4 to 20 mA)

1
condenser fan 2 MV4:1 105 XA1:104

M
18 18
condenser fan 2 MV4:2 106 XA1:108/XA1:102
21 21
crankcase heater RR2 107 KM3:62
18 18
crankcase heater RR2 108 XA1:106
38 38
aux 1 AUX1:1 109 KR2:11
37 37
aux 1 AUX1:2 110 KR2:14
25 25

L
kriwan AP2:L 111 FU2:2/XA1:113 27 27
AUX 1 AUX1:1 109

1. Following drilling template, drill 4 (6) holes on the wall:

24 24

N
kriwan AP2:N 112 KR1:A2/FU1:2 26 26
25 25 AUX 1 AUX1:2 110
kriwan AP2:11 113 XA1:128/XA1:111
28 28 18 18
kriwan AP2:14 114 XA1:115 termostato di sicurezza TS1 117

P
28 28 20 20
pressure switch SP2 115 XA1:114
29 29 termostato di sicurezza TS1 118
pressure switch SP2 116 KR1:A1 19 19
27 27 Clicson evaporatore SP3 119
security thermostat TS1 117 ??:J10/NO1 380
31 31 22 22
security thermostat TS1 118 KM2:A1 Clicson evaporatore SP3 120
30 30 16 16
evaporator clicson SP3 119 ??:J10/NO2
33 33 UltraCella AP3:L 128
evaporator clicson SP3 120 KM1:A1 15 15
29 UltraCella AP3:N 129
121 ??:J11/C3/4/5
32 28 28
Ultra 3PH

122 XA1:126/??:J11/NO3 defrost ST1 140

cable glands to connect: power supply cables, serial cable, probes

Drill side surface of expansion module where it’s necessary and fit
Fix panel to the wall by using screws with suitable length to wall thickness
35
I/O module

123 29 29

P
35 35 defrost ST1 141
pump down TK1 124 30 30

186
130
34 34 defrost aux ST2 142
pump down TK1 125 KM3:A1
32 32 29 29
liquid valve YV1 126 XA1:122 defrost aux ST2 143
24 24 31 31
127

17
liquid valve YV1 KM3:A2/XA1:129 146
25 25 ventilatore evaporatore 0-10 Vdc Y TS2:Y
ultracella ULTRACELLA:L 128 ??:J12/NC6/XA1:113 29 29
24 24 ventilatore evaporatore 0-10 Vdc GND TS2:GND 147
ultracella ULTRACELLA:N 129 XA1:127/KR2:A2
39 39 25 25
AP1

defrost ST1 140 ??:J2/U1 consenso unita' motocondensante AUX2:1 148

40 40 24 24
defrost ST1 141 XA1:143
41 41 consenso unita' motocondensante AUX2:2 149
defrost aux ST2 142 ??:J2/U2 32 32
KR2

40 40 controllo - AP1:J6/- 160

defrost aux ST2 143 XA1:145/XA1:141
42

Ultra 3PH
42 33 33
temp condensatore ST3 144 ??:J2/U3 controllo + AP1:J6/+ 161

I/O module
40 40
temp condensatore ST3 145 ??:J2/GND/XA1:143 34 34
45 45 controllo GND AP1:J6/GND 162
fan evaporatore 0-10vdc Y 7AP1:Y 146 ??:J2/U6 17
40 40 PE1
fan evaporatore 0-10vdc GND 7AP1:GND 147 KR1:11
46 46
controller - AP1:J6/- 160 AP:- PE2
47 47
controller + AP1:J6/+ 161 AP:+

AWG 22
48 48 PE3
controller GND AP1:J6/GND 162 AP:GND

TC1
AP1
26
PE109 TC1:PE

KR2
Important:

KR3
KR3

XA1
XA1
KM2

KM3
current absorption on the loads
XP1

KM2
KM1

XP1
cables (probes, digital inputs) and serial cable

KM1
QF2
QF1

QF2

90
80
70
63
QF1

QM1
• use cable with section suitable to current rating they have to carry
• separate the power cable (power supply, actuators) from the signal

UltraCella +0300083EN - rel. 1.7 - 07.01.2016

2. Connect three-phase expansion to UltraCella by shielded serial cable
• after powering on three-phase expansion check the correct rating
• connect clamp marked with PE to the ground of power supply system
ENG
ENG
3. Close frontal by screwing the 6 screws HACCP - CAUTION
4. At the first start-up of the unit, it’s suggested to calibrate motor circuit
When the temperature measurement is relevant for Food Safety (see
breaker on effective compressor absorption rating
HACCP), will be used only temperature probes suggested by Carel. The
standards in force may require the compilation and preservation of
appropriate documentation, as well as periodic checks on instrumentation
and sensors. If in doubt, consult the person in charge of food safety or the
manager of the plant.

2.11 Connection in supervisoring network

Warnings:
• properly fix the converter to avoid disconnections;
5. Power on UltraCella (230Vac) and expansion three-phase module • perform the wiring without power supply;
(400Vac) • keep the cables of the converter CVSTDUMOR0 separate from power
6. Activate magnetothermic switch and motor circuit breaker cables (supply and relay outputs).
The RS485 converter allows you to connect to the UltraCella control
2.10 Installation network to the monitoring network for complete control and monitoring
of controls connected. The system provides a maximum of 207 units with
Proceed as follows for installation, making reference to the wiring
a maximum length of 1000 m. For the connection it is requested the
diagrams in the previous paragraphs:
accessory standard (RS485-USB converter cod. CAREL CVSTDUMOR0) and
1. Connect the supply and probes: the probes can be remote-controlled up
a terminating resistor of 120 Ω to be placed on the terminals connected
to a maximum distance of 10 metres from the controller as long as
to the last control. Connect RS485 converter to the controls as shown in
cables with minimum section of 1 mm2 are used.
the figure. For assigning the serial address see the parameter H0. See the
2. Program the control: as indicated in chapter“Commissioning”and“User
instruction sheet of the converter for further information.
interface”;
3. Connect the actuators: the actuators should only be connected after
having programmed the controller. It is recommended to carefully
evaluate the maximum capacities of the relays indicated in table UltraCella 1
USB
“Technical specifications”.
4. Connection to the serial network (if present): all controls are fitted with a
serial connector for connection to the supervisory network.

Warnings: avoid installing UltraCella control system in environments with CVSTDUMOR0

the following characteristics: USB-485 T-
T+
T+
T- to BMS
• relative humidity over 90% non-condensing; Converter GND GND port

• strong vibrations or knocks;

• exposure to continuous jets of water;
• exposure to aggressive and polluting atmospheric agents (e.g.: sulphur
and ammonia gases, saline mist, smoke) to avoid corrosion and/or
oxidation; UltraCella ...n
• high magnetic and/or radio frequency interference (e.g. near
transmitting antennas);
• exposure of the control system to direct sunlight and atmospheric
agents in general.

The following recommendations must be respected when connecting T+ to BMS

120 Ω T-
port
the controllers: GND

Warnings:
• incorrect connection of the power supply may seriously damage the
control system;
• use cable ends that are suitable for the terminals. Loosen every screw
and fit the cable end, next tighten the screws and gently pull the cables Fig. 2.t
to check their tightness. If using an automatic screwdriver, adjust the UltraCella can be connected to both PlantVisor and PlantWatch via BMS
torque to a value less than 0.5 N · m; port (RS485).
• separate as much as possible (by at least 3 cm) the probe signal and Starting from 1.5 release software, both CAREL and Modbus protocols are
digital input cables from inductive loads and power cables, to avoid available from BMS port, selectable by H7 parameter.
any electromagnetic disturbance. Never lay power cables and probe - H7 = 0 CAREL protocol
cables in the same cable conduits (including those for the electrical - H7 = 1 Modbus protocol
panels). Do not install the probe cables in the immediate vicinity of
power devices (contactors, circuit breakers or other). Reduce the Starting from software release 1.7, the baud rate, stop bits and parity of
length of the sensor cables as much as possible, and avoid spirals the BMS port can be set using parameters H10, H11 and H12; the data bits
around power devices; setting on the other hand remains fixed at 8.
• only use IP67 guaranteed probes as end defrost probes; place the
probes with the vertical bulb upwards, so as to facilitate drainage of
any condensate. Remember that the thermistor temperature probes
(NTC) have no polarity, so the order of connection of terminals is not
important.

Caution: in order to ensure the safety of the unit in the event of

serious alarms, all the electromechanical safety devices required
to guarantee correct operation must be fitted on the unit.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 18

 ENG
Par. Description Def Min Max U.M. Procedure:
H10 BMS baud rate bit/s 4 0 9 - 1. remove the lower frame and insert the USB memory key. The red and
0 1200 5 38400 green LED beside the key will light up once in sequence to indicate
1 2400 6 57600 the recognition by the unity of the USB memory key;
2 4800 7 76800 2. bring the control to OFF to upload (to copy the configurations from the
3 9600 8 115200 USB key to the controller); to download (to copy the configurations
4 19200 9 375000 from the controller to the USB key), the controller can be in ON status;
H11 BMS stop bits 2 1 2 - 3. press at the same time Prg and Set for 2 s and access the multifunction
1 1 bit stop menu: the message “HcP” will appear;
2 2 bit stop 4. press “UP” until reaching the entry “USb”;
H12 BMS parity 0 0 2 - 5. press “Set”;
1 odd 6. choose whether you want to DOWNLOAD the parameters (= dnL), to
2 even UPLOAD them (=uPd) or to exit the page (EXt);
7. press “Set”; the green LED will light up and will remain lit to indicate that
Note: To make the change active, switch on and switch off the unit. the upload / download of parameters occurred; if, for some reason, the
procedure should not be successful, the red LED will turn on;
8. extract the key. The LED turns off. The file is “.txt”type, and it can be
displayed on the computer.
2.12 UltraCella Service terminal
The UltraCella Service Terminal has to be connected via a dedicated
connector, that can be accessed after removing the lower frame
Using the “UltraCella Service Terminal” you can: 
• during the first commissioning: insert the first configuration parameters
following the guided procedure (wizard);
1 2
• during normal operation: 1 2

1. display the active loads and the main variables: temperature, humidity;
2. perform the control programming, facilitated by contextual help.

1 2 1 2

2
1

1 2 1 2

Note: the figure refers to the screens on models with single row
Fig. 2.u display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
as well as the message indicated, during navigation the display shows the
scrolling message "recipes in USB device” on the second row.
2.13 Upload/downloadparameters(USBmemory
key)
Note: the download and upload operations, as well as the 10 lists
The USB memory key must be placed in the connector accessible after of parameters, also copy all the other parameters (one value only
removing the lower frame. Using the USB memory key you can: for all 10 lists).
1. download the parameters set (r01...r10): control saves inside the key the
10 parameters set;
2. upload the parameters set (r01...r10): control loads from the key the
10 parameters set);

2
1

USB key

Fig. 2.v
19 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
3. USER INTERFACE
The front panel contains the display and keyboard, made up from 10
or 11 keys (depending on the model), which, pressed individually or
together, allow to perform all of the controller programming operations.
The accessory UltraCella Service terminal, accessory terminal, allows the
commissioning of the control system via a guided procedure (Wizard)
and also programming the parameters with a contextual help that
explains the various functions.

3.1 Display
On the LED display is shown the temperature range from -50 °C (-58 °F)
to +150 °C (302 °F). The resolution of the tenth for temperatures in the
range -19,9…99,9. In case of alarm the value of the probe is displayed in
alternance with the codes of the active alarms. During programming, it
displays the codes that identify the parameters and their value.
Note: you can select the standard display by properly configuring
parameter /t1 (/t1 and /t2 for double digit models).

Front panel for single row display models Front panel for double row display models
UltraCella Service Terminal (accessories)
cod. WB000S* cod. WB000D*

MENU
Multifunction menu
MENU
Multifunction menu
H M
HELP E E
HACCP L
P
Multifunction menu N
U

H M
HELP E E
PRG
HACCP L
P
Multifunction menuSET N
U

ESC
HACCP
PRG SET

ESC
HACCP

Fig. 3.a Fig. 3.b Fig. 3.c

Icons table on models with single row display P/Ns WB000S*

Normal operation
Icon Function Note
ON OFF Flashing
Technical Alarms, for example alarm due to EEprom Serious problem detected. Please contact
support or probe fault technical service
HACCP HACCP function enabled - HACCP alarm saved (HA and/or HF)

Door Door open Door Close Door open and door alarm active
Blinks when the activation of the
Compressor On Off Waiting for activation
compressor is delayed by safety times.
Blinks when the activation of the
Fan On Off Waiting for activation
compressor is delayed by safety times.
On if a scheduled defrost is
Clock
requested
Tab. 3.a

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 20

 ENG
Icons table on models with two rows display P/Ns. WB000D*
Normal operation
Icon Function Note
ON OFF Flashing
Technical Alarms, for example alarm due to EEprom Serious problem detected. Please contact
support or probe fault technical service
HACCP HACCP function enabled - HACCP alarm saved (HA and/or HF)

Door Door open Door Close Door open and door alarm active
Blinks when the activation of the
Compressor On Off Waiting for activation
compressor is delayed by safety times.
Blinks when the activation of the
Fan On Off Waiting for activation
compressor is delayed by safety times.
On if a scheduled defrost is
Clock
requested
Celsius Temperature visualization in
- .
degrees Celsius degrees
Farenheit Temperature visualization in
-
degrees Farenheit degrees
humidity
Humidity visualization -
percentage
Tab. 3.b

3.2 Keyboard
Key Normal operation Blink
Pressing the individual key Combined pressure with other keys
• Pressed for 2 s, turns the control OFF
• Pressed for 2 s, turns the control ON
On/Off
• ESC function, return to higher level Prg + Set: if pressed at the same time for 2
• Pressed for 2 s, enters the programming menu s, allow access to the multifunction menu
• In case of alarm: mutes the audible alarm (buzzer) and Available only in case of alarm
deactivates the alarm relay
ALARM • Pressed for 2 s, reset the manual reset alarms
• Turns the light on/off

• Turns auxiliary output 1 on/off (*) Flashing for 5 seconds: attempt to activate
auxiliary output 1 from button, yet output
has different configuration
• Turns auxiliary output 2 on/off (*) Flashing for 5 seconds: attempt to activate
auxiliary output 1 from button, yet output
has different configuration
• Activates/deactivates manual defrost Awaiting activation

DEF
• Set point setting Prg + Set: if pressed at the same time for 2 Indicates that the set point is not that
• Value setting s, allow access to the multifunction menu the value set for parameter St but rather
defined by one of the following algorithms:
• Set point variation from digital input
(St+r4)
• Set point variation by time band (St+ r4)
• Set point ramps (variable set point)
• Value increase/ decrease
/
UP/DOWN
Tab. 3.c
(*) To activate outputs AUX1 / AUX2 by button, set H1/H5=2. If parameters
are not set, if AUX1/AUX2 key are pressed, they blink for 5 seconds

21 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
3.3 Programming
The parameters can be modified using the keyboard. Access to the
configuration parameters is protected by a password that prevents
unwanted modifications or access by unauthorised persons. With the 
password you can access and change all the parameters of the control.
1 2 1 2

Note: in the LED display model the keys are illuminated according
to the menu where the user is operating, in order to facilitate
navigation. Note: in the parameters or set point modification procedures, the
new value is saved every time the Set key is pressed.

Category Text Category Text

3.3.1 Changing the set point Probes Pro Clock rtc
In order to change the set point St (default =0°C): Control CtL Door and light doL
1. the control system displays the standard display visualization; Compressor CMP Recipes rcP
2. press Set for 2 s: on the display appears the current value of the set point; Defrost dEF Generic functions GEF
Alarms ALM EVD EVO EVO
3. press UP/DOWN to reach the desired value;
Fan FAn EVDice ICE
4. press Set to confirm the new set point value. The control returns to Configuration CnF Three-phase modules 3PH
standard display visualization. HACCP HcP
Tab. 3.d
Note: if no key is pressed, after about 120 s the control
automatically returns to standard display..


1 2 1 2

3.3.3 Modificationoftheparameters(formodelswithdouble
digit display cod. WB000D*)

Procedure:
 1. to modify the parameters, first switch the controller OFF (press ON/OFF
button);
1 2 1 2
2. press Prg for 2 sec: the second row of the display will show “PASS”
(password required);
3. press UP/DOWN to enter the password: 22;
Note: the figure refers to the screens on models with single row 4. press Set; the second row of the display will scroll the name of the first
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, category of parameters: Probes (see the previous table and the
as well as the message indicated, during navigation the display shows the parameter table);
scrolling message “Setpoint” on the second row 5. press Set: the second row of the display will scroll the code and
description of the first parameter in the category: /21 – Probe1
meas. stab.; the first row of the display will show the current value of
the parameter;
6. press Set: the value on the first row of the display flashes, to indicate that
3.3.2 Modificationoftheparameters(formodelswithsingle
the value can be modified;
digit display cod. WB000S*) 7. press UP/DOWN until reaching the desired value;
Procedure: 8. press Set to confirm the new value; the value will stop flashing;
1. to modify the parameters, first switch the controller OFF (press ON/OFF 9. press UP/DOWN to scroll the other parameters;
button); 10. repeat steps 6) to 9) to modify other parameters;
2. press Prg for 2 s: on the display appears the message “PAS” - password 11. press Prg to return to the top level of parameter categories, or UP/
request; DOWN to move the next category: CtL (Control). Then repeat steps
3. press UP/DOWN and insert the password: 22. If you press Set, the code of from 5) to 9) to access the category and modify other parameters;
the first parameters category will appear: Probes (see the following 12. press Prg once or more than once to exit the parameter setting
table and parameters table); procedure and return to the standard display.
4. press Set: the first parameter of the category will appear: /21;
5. press UP/DOWN until reaching the parameter to be modified;
6. press Set key to display the parameter value;
7. press UP/DOWN to reach the desired value;
8. press Set to confirm the new value and return to parameter code display;
9. repeat the operations from 5) to 8) to change other parameters;
10. press Prg to return to higher level of the parameters categories and UP/
DOWN to pass to the next category: CtL. Repeat steps from 4) to 8) to
access the category and change other parameters;
11. press one or more times Prg to exit the parameters modification
procedure and return to standard display visualization.

1 2 1 2

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 22

 ENG
Par. Description Def Min Max U.o.M.
tcE Enabling date modification procedure 0 0 1 -
0/1=No/Yes
tcT Date/ time change 0 0 1 -
Action on change 01 or 10
y__ Date/ time: year 0 0 37 -
M__ Date/ time: month 1 1 12 -
d__ Date/ time: day of the month 1 1 31 -
h__ Date/ time: hour 0 0 23 -
n__ Date/ time: minute 0 0 59 -

1 2 1 2

Note: the figure refers to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, as well
as the message indicated, during navigation the display shows with a
scrolling message, parametercode and description: “tce - enable data
modification”.

3.3.5 Example 2: set the scheduled defrosting periods

Procedure:
1. access the parameters modification menu as described in the relative
paragraph;
2. enter category “rtc”;
3. press UP and select the parameters“ddi (i = 1…8”) to select the frequency
of the ith defrost, based on the indications in the table below;
4. press UP and pass to the defrost hour and minute;
5. press once or more times Prg to save and return to standard visualization.
0 ith defrosting disabled
1…7 Monday…Sunday
8 From Monday to Friday
9 From Monday to Saturday
10 Saturday and Sunday
11 Daily

Note: in the parameters or set point modification procedures, the

new value is saved every time the Set key is pressed. 

1 2 1 2
Note: if no key is pressed, after about 120 s the control
automatically returns to standard display.

Note: the figure refers to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, as well
3.3.4 Example 1: current date/time setting as the message indicated, during navigation the display shows with a
scrolling message, parameter code and description: “dd1 - defrost1-day”
Procedure:
1. access the parameters modification menu as described in the relative
paragraph;
2. enter category “rtc”;
3. select parameter “tcE” and set it to 1 to enable the date exchange;
4. press UP 2 times and then set the parameters regarding the year (Y),
month (M), day of the month (d), hour (h), minutes (n) (see table
below);
5. press UP, select tct parameter and set it from 0 to 1 or from 1 to 0 to
perform the data/ time change;
6. select again parameter tcE and set it to 0;
7. press one or more times Prg to save the date/ time and return to
standard display.

23 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
3.4 Procedures

3.4.1 Parameter set selection 

The control can work with 10 sets of parameters, pre-set in the factory
by Carel, but modifiable to suit your requirements, indicated with r01 r10 11 22 11 22

(recipe 1 ... recipe 10);

In order to select the current parameters set (control in OFF):
1. from parameters modification menu, access the category“rcP”and press
Set; the message "bni" will appear; press Set again; the message
“r0i” will appear where "r0i" ranges from 1 to 10 and indicates the

currently active configuration on UltraCella;
2. press UP/DOWN to select the parameters set to be loaded; you can
choose between r01…r10; for example r02 (figure); 1 2 11 22

3. Press Set to confirm.The control system loads the chosen parameters set;
4. Press once or more times Prg to return to standard display..
Note: the figure refers to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, as well
as the message indicated, during navigation the display shows the
scrolling message “bni - recipe index now active” on the second row.

Param Configurations
Std Red meat Poultry Fish Vegetables Fruit Summer and Frozen Restaurant - Bakery
CAREL tropical fruit fresh food
Heater Heater Heater defrost Heater defrost Timed defrost No defrost, Heater defrost Heater defrost Heater
defrost defrost with probe, with probe, by stopping evap. fans with probe, with probe, defrost
with probe, with probe, evap. fans evap. fans compressor, on with evap. fans evap. fans with probe,
evap. fans evap. fans controlled by on with evap. fans on compressor on with on with evap. fans
controlled by controlled by temperature compressor with compressor on, humidity compressor on compressor on controlled by
temperature temperature and off during on and on on and on control and off during and on during temperature
and off and off defrost during defrost, during defrost, defrost defrost and off
during during humidity humidity control during
defrost defrost control defrost
r01 r02 r03 r04 r05 r06 r07 r08 r09 r10
/4 0 0 0 0 0 0 0 0 0 0
/t2 6 4 4 4 4 4 11 4 4 4
/A2 1 1 1 1 1 0 0 1 1 1
/A3 0 0 0 0 0 0 0 0 0 0
/A4 0 0 0 0 0 0 0 0 0 0
/A5 0 0 0 0 1 1 1 0 0 0
St 0 -0,5 0 1 4 4 10 -22 3 -20
rd 2 2 2 2 2 2 2 2 2 2
StH 90 90 90 90 95 95 85 90 90 90
rdH 5 5 5 5 5 5 5 5 5 5
r1 -50 -5 -5 -5 0 0 5 -25 0 -25
r2 60 10 10 10 10 10 15 -15 10 -10
r3 0 0 0 0 0 0 1 0 0 0
c11 4 4 4 4 4 4 4 4 4 4
d0 0 0 0 0 0 2 0 0 0 0
dI 8 12 12 12 24 24 8 15 13 15
dt1 4 20 15 10 8 4 4 15 10 15
dP1 30 60 60 60 45 30 30 60 90 60
AL 0 4 4 4 4 5 5 10 4 10
AH 0 5 5 10 5 5 5 6 5 6
Ad 120 60 60 120 60 60 60 60 60 60
A5 0 0 0 0 0 0 0 0 0 0
A9 0 0 0 0 0 0 0 0 0 0
F0 0 1 1 1 0 0 0 0 0 1
F1 5 -8 0 0 5 5 5 5 5 -22
F2 30 30 30 30 15 15 10 30 30 30
F3 1 1 1 1 0 0 0 1 0 1
F4 1 1 1 1 1 1 1 1 1 1
H1 1 0 0 0 0 0 0 0 0 0
H5 1 2 2 2 15 15 15 3 2 3
HO1 0 0 0 0 0 0 0 0 0 0
c12 5 5 5 5 5 5 5 5 5 5
d8d 30 30 30 30 30 30 30 30 30 30
tLi 120 120 120 120 120 120 120 120 120 120
A4 0 0 0 0 0 0 0 0 0 0
Tab. 3.e

For all other parameters not included in this table, the default values will be used for all configurations, as shown in chap.7 Parameter table.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 24

 ENG
3.4.2 Parameters set to default values DEACTIVATION MANUAL DEFROST
In order to set all parameters sets to the factory values (default): Press DEF: message “Off ” will appear and the control ends the defrost
1. from parameters modification menu, access the category“rcP”and press
Set; the message “r0i” will appear, where "i" indicates the currently
active configuration ;
2. press UP/DOWN and display the message “bnr”;
3. press Set: the message “no” will appear; 
4. press UP/DOWN: the message “Std” will appear;
5. press set: the control system brings all parameters sets to default values; 1 2 1 2

6. press one or more times Prg to return to standard display.

Note: in this manner all the modifications are erased and the Note: The Figures refer to the screens on models with single row
original factory values are restored to the default ones, indicated display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
in parameters table. the message “Off ” appears on the second row of the display.

3.4.3 Defrost
In order to activate the defrost by temperature, the defrost probe must
detect a temperature lower than the temperature relative to defrost end 3.4.4 AUX1/AUX2/Light
(par. dt1). The defrost by time is activated setting dI parameter to a value In order to activate/deactivate the digital outputs AUX1/AUX2 (auxiliary
>0. mode outputs) from keyboard set the parameters H1/H5=2. The light
output is fixed and cannot be configured.
Procedure:
1. press DEF. There can be 3 cases: ACTIVATION
2. if the defrost probe detects a temperature greater than the value of the Press keys AUX1/AUX2/Light: message “On” will appear and the control
defrost end temperature, the control displays the message “no” and activates the relative output.
the defrost is not activated;
3. if there are protections in progress, the control waits before entering
the defrost. The DEF button blinks and when conditions permit, the  
control enters the defrost;
4. control comes into defrost, it shows the message “On”. The DEF key is lit 1 2 1 2 1 2

and the defrost output is enabled. The display depends on parameter

d6.
DEACTIVATION
Par. Description Def Min Max U.o.M. Press keys AUX1/AUX2/Light: message “Off ” will appear and the control
d6 Terminal display during defrost 1 0 2 - deactivates the relative output.
0 = Temperature alternated with dEF
1 = Last temperature shown before
defrost
2 = dEF  
1 2 1 2 1 2

ACTIVATION MANUAL DEFROST

Note: if output AUX1/2 was not enabled by setting H1/H5 = 2, the
relative key blinks to signal that the output is not active. However,
the messages “On” and “Off ” will appear
1 2 Note: The Figures refer to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
Request a manual defrost
the message “On” and “Off ” appear on the second row of the display.

1 2 1 2 1 2
3.4.5 On/Off
In order to turn off the control from keyboard:
• press On/Off for 2 s.
The display will alternate Off to the standard display.
The key On/Off lights up and any active output relay will be deactivated.

1 2 1 2 1 2

Case 1 Case 2 Case 3


Note: The Figures refer to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, 1 2 1 2
the message “no” and “On” appear on the second row of the display.

Note: The Figures refer to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
the message “On” and “Off ” appear on the second row of the display.

25 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
In order to turn on the control from keyboard: Par. Description Def Min Max U.o.M.
• press On/Off for 2 s. HA Date/time of last HA alarm 0 - - -
HA1 Date/time of penultimate HA alarm 0 - - -
“On” will appear on the display and then control returns to the standard HA2 Date/time of third from last HA alarm 0 - - -
display. The output relay will be re-activated. Han Number of HA alarms 0 0 15 -
HF Date/time of last HF alarm 0 - - -
HF1 Date/time of penultimate HF alarm 0 - - -
HF2 Date/time of third from last HF alarm 0 - - -
HFn Number of HF alarms 0 0 15 -
 Hcr HACCP alarms cancelling 0 0 1 -
Action on variation 01 or 10
1 2 1 2
Each alarm is displayed with scrolling text, which contains the day of
week, hour, minute, and the temperature that caused the alarm. This is
Note: The Figures refer to the screens on models with single row a list (FIFO) in which are stored only the last 3 alarms. Instead, the alarm
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, counters (HAn, HFn), after reaching 15, they stop.
the message “On” and “Off ” appear on the second row of the display.
Example: HA alarm triggered Thursday at 13:17, with detected
temperature of 36.8 °C.

3.5 Multifunction menu

The multifunction menu allows you to access: 
• “HcP”: HACCP alarms display, type HA and HF alarms and reset;
• “cc”: continuous cycle activation/deactivation; 1 2 1 2

• “rEc”: display maximum and minimum temperature, cancellation and

re-start recording;
• “I/O”, input/output: displaying the temperature read by the probe and
digital input status;
• “USB”: USB key;
• “InF”: information  
• “Log”: datalogging function
• "SOF" UltraCella software update 1 2 1 2

Procedure:
1. press Prg and Set for 2 s; the first menu will appear: HcP;
2. press UP/DOWN to view other entries;
3. press Set to enter: follow the steps described in the following sections for  
the relative explanations;
4. Press one or more times Prg to return to standard display.
1 2 1 2

     
Note: the figure refers to the screens on models with single row

display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
as well as the message indicated, during navigation the display shows the
1 2 1 2
scrolling message “HACCP Alarms” on the second row.

Note: the figure refers to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
as well as the message indicated, during navigation the display shows the 3.5.2 Continuous cycle
scrolling message “Menu” on the second row.
For explanation of continuous cycle, see chapter 6.
In order to activate the continuous cycle
• the control must be on;
3.5.1 HACCP alarms display • the value of the parameter cc must be >0.
For explanations regarding HACCP alarms, consult chapter “Alarms”.
Par. Description Def Min Max U.o.M.
In the multifunction menu you can see the date and time of the last 3 cc Continuous cycle duration 0 0 15 hour
alarms HA and HF. After entering the multifunction menu (see previous
par.), select with UP / DOWN the message “HcP”. After entering the multifunction menu (see previous par.), select with UP
/ DOWN the message “cc”.
Procedure:
1. press Set, and then UP / DOWN to display the parameters in the following
table: you can see the number of alarms, the relative date and you ACTIVATION
can also cancel the alarms; Procedure:
2. press Set to display the alarm date and time; 1. press Set; the message “OFF” will appear (continuous cycle disabled);
3. press Prg until you return to standard display. 2. press UP/DOWN: the message “ON” appears;
3. after about 1 s the control returns to standard display and the
compressor icon appears, to show the activation of the function.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 26

 ENG

  

1 2 1 2 1 2 1 2

     
Note: by pressing UP you will cancel both the maximum and the
minimum recorded temperature.
 Note: the Figures refer to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*:
1 2 1 2 • MAX --> Max temp recorder (scrolling)
• 36,9 --> Max
Note: the figure refers to the screens on models with single row • 13.Y --> year
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, • 11.M --> month
as well as the message indicated, during navigation the display shows the • 22.d --> day
scrolling message “Continuous cycle” on the second row. • 9.H --> hour
• 34.m --> minute
DEACTIVATION
Follow the same activation steps and set “OFF”.
3.5.4 Input/output status display
Note: the activation of the continuous cycle function does not After entering the multifunction menu (see previous par.), select with UP
appear on display in standard mode. / DOWN the message “I/O”.

Procedure:
1. Press Set: the message “b1” appears regarding the probe B1;
3.5.3 Maximumandminimumtemperaturemonitoring 2. Press Set once again: the value read on probe B1 will appear alternating
The control allows you to continuously record the minimum and with the message b1;
maximum temperature measured by the control probe. The monitoring 3. Press Prg to return to upper level;
is always active. The values can be reset, as described below. 4. Press UP/DOWN and repeat steps 1)…3) to display the inputs/outputs
indicated in table;
After entering the multifunction menu (see previous par.), select with UP 5. Press one or more times Prg to return to standard display
/ DOWN the message “rEc”.
Text Description TextDescription
Procedure: b1 Analogue input 1 do5 Digital output 5
1. press Set; the message “MAX” will appear (maximum registered b2 Analogue input 2 do6 Digital output 6
temperature); in order to see the maximum temperature, registration b3 Analogue input 3 Y1 Analog output 1
date and time pass to point 3 or: b4 Analogue input 4 ESu EVD EVO suction temp.
2. press UP/DOWN: the message “MIn” appears (minimum temperature b5 Analogue input 5 ESA EVD EVO evap. temp.
di1 Digital input 1 ISu EVD ICE suction temperature
registered);
di2 Digital input 2 ISa EVD ICE evaporation temperature
3. press Set: the maximum/minimum recorded temperature will appear di3 Digital input 3 U1 Defrost probe Sd1 (3PH model)
along with the date/time of record (y=year, m = month, d = day, h = do1 Digital output 1 U2 Auxiliary defrost probe Sd2 (3PH
hour, m = minutes. Press UP to cancel (both temperatures), appears model)
RES and the control exits the menu, or press Prg for more than once do2 Digital output 2 U3 Condenser probe Sc (3PH model)
and exit the display. do3 Digital output 3 dU4 Motor protector (3PH model)
do4 Digital output 4 dU5 High/low pressure switch or Kriwan
Example: maximum registered temperature 36.9°C on 22/11/2013 at 9.34. alarm (3PH model)
Tab. 3.f
Note: the opened digital inputs/outputs are displayed along with
the message “oP” (=open), those closed with “cLo” (=closed).

Example 1: probe B1 measures the temperature of -1.0 °C..
1 2
1 2

 

1 2 1 2
 

1 2 1 2

 

1 2 1 2

 
Note: the figure refers to the screens on models with single row
1 2 1 2
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
as well as the message indicated, during navigation the display shows the
scrolling message “Probe1 status” on the second row “.
27 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
Example 2: digital input 1 is closed.

  
1 2 1 2 1 2

1 2

Note: the figure refers to the screens on models with single row
     
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
as well as the message indicated, during navigation the display shows the
Note: the figures refer to the screens on models with single row
scrolling message “Digital input 1 status” on the second row.
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
as well as the message indicated, during navigation the display shows the
scrolling message “recipes in USB device” on the second row

3.5.5 USB memory key Note: the download and upload operations, as well as the 10 lists
Parameters upload/download of parameters, also copy all the other parameters (one value only
for all 10 lists).
Preliminary operations:
1. remove the lower frame and insert the USB memory key;
2. set the control to OFF.
Download saved alarms
Starting from software release 1.5, the last 64 alarms activated and saved
on UltraCella can be downloaded to a USB flash drive, in order from the
most recent to the oldest, in csv format. When the 64th alarm is saved, the
1
2 next one will overwrite the oldest.
Alarms that have been saved and are no longer active can only be
displayed on the UltraCella Service terminal, but can be downloaded
both from the terminal and the LED interface.

• Alarm log file name: AlarmLog.csv

1. remove the bottom frame and plug in the USB flash drive. The red
USB key
and green LEDs on the side of the key will come on individually in
sequence to indicate that the unit recognises the USB flash drive;
Fig. 3.d 2. press Prg and Set for 2 sec; the first menu is displayed: “HcP”;
3. press UP 4 times until reaching the “USB” menu item;
After entering the multifunction menu (see previous par.), select with UP
4. press Set; the first submenu is shown: “rcP”;
/ DOWN the message “USb”.
5. press UP to access the “ALG” submenu;.
Procedure:
Press Set: the following commands will appear by scrolling UP/DOWN:
• rcP: press Set to confirm;
• EXt: press Set to exit;
• dnL: press Set, the control saves inside the key the 10 parameters set:
r01…r10;
1 2
• uPd: press Set, the control loads from the key the 10 parameters set:
r01…r10;

Note 6. press SET to confirm the download of the saved alarms. The message
“ALG” will flash during the download procedure; at the end, “ALG” will
• the parameters are saved in a text file type. txt, which can be viewed stop flashing and the green LED next to the USB port will come on,
on the computer; indicating the end of the procedure; if for some reason the procedure
• for information regarding the switching of the LEDs, see chapter 2.10.
is not successful, the alarm icon will be shown on the display;
7. unplug the key; to exit the “ALG” menu, press PRG twice.

Note: If for some reason the procedure is not successful, when


exiting the menu, as well as the alarm icon on the display, the
1 2 1 2 error message “ALM” will be displayed. The error message will be cleared
the next time the alarms are downloaded successfully or when restarting
the controller.

Example: alarms saved starting 2 April 2014 at 10:30:00. The alarm log was
downloaded to the USB flash drive at 16:22:45 on the same day.
 Start -> alarm activated
Stop -> alarm reset
1 2 1 2
TIME ID NAME EVENT VAR1 VAR2
2014-04-02 T10:30:00+00:00 11 ALARM_Ed1.Active Start
2014-04-02 T16:22:45+00:00 11 ALARM_Ed1.Active Stop

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 28

 ENG
3.5.6 Information
In the information menu you can view the software release.
After entering the multifunction menu (see chapter 3.4), select with UP /
DOWN the message “InF”.

  USB key

1 2 1 2 1 2 Fig. 3.f

Fig. 3.e To activate the data logging function, the probe/probes to be recorded
Procedure: must be configured (up to max 2) through the parameters tr1 and tr2.
1. press Set: the message “vEr” appears regarding the software revision; The sample time (for both the variables) is selectable between 2 and 60
2. press Set once again: the software revision will appear (e.g. 1.7); minuts (default 5).
3. press one or more times Prg to return to standard display .
Par. Description Def Min Max U.o.M.
Note: the figure refers to the screens on models with single row First temperature to be 0 0 8 -
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, tr1 recorded selection
as well as the message indicated, during navigation the display shows the 0 = no log
scrolling message “Application version” on the second row 1 = Sv
2 = Sm (sonda letta da B1)
3 = Sr
4 = Sd1
3.5.7 Data logging function 5 = Sd2
UltraCella introduces the data logging function to cold room control, 6 = Sc
offering the possibility to record the temperature or the humidity read 7 = SA
by two probes. 8 = Su (humidity probe)
tr2 Second temperature to be 0 0 8 -
How to download the file with variables recorded by UltraCella: recorded selection
1. remove the bottom frame and insert the USB flash drive. The red and 0 = no log
green LEDs next to the flash drive will come on once in sequence to 1 = Sv
indicate the that unit has recognised the USB flash drive; 2 = Sm (sonda letta da B1)
2. press Prg and Set for 2 s; the first menu will be displayed: “HcP” 3 = Sr
3. press UP or DOWN until reaching the “LoG” menu item; 4 = Sd1
4. press SET to confirm the download of the recorded variables (log file) to 5 = Sd2
the USB flash drive. The message “LoG” will flash during downloading; 6 = Sc
at the end, “LoG” will stop flashing to indicate that the download has 7 = SA
been completed; if the procedure fails for some reason, the alarm icon 8 = Su (humidity probe)
trc Sample time temperature 5 2 60 min
will be shown on the display; recording
5. remove the flash drive; to exit the “LoG” menu, press PRG and/or SET.
• Channels recorded: two probes selected through tr1 and tr2
parameters
• Start logging: as soon as parameter tr1/tr2 is set to a value >0. The
instant the setting is confirmed is recorded in the log under event
name “Start”
• Sample time: trc (minutes) for both the variables
• Data logging duration: depends on the sampling time trc and the
1 2 maximum number of samples Nrec that UltraCella can record (209000),
based on the following formula:
Note: the figure refers to the screens on models with single row Data logging duration = Nrec * trc
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
as well as the message indicated, during navigation the display shows the Sampling time (trc) Data logging duration
2 min 290 days
scrolling message “recorder” on the second row.
5 min 726 days (around 2 years)
10 min 1451 days (around 4 years)
Note: if the procedure fails for some reason, when exiting the 30 min 4353 days (around 8 years)
60 min 8708 days (around 24 years)
menu, as well as the alarm icon the error message “LoG” will • Data extraction: any USB flash drive available on the market can be
also be shown on the display. used
The message error will be cleared after the next correct download or • Extracted log file names: Log_UltraCella_1.csv for the first variable
when restarting the controller. selected through the parameter tr1, Log_UltraCella_2.csv for the
When the probes to be recorded are suitably configured through the second variable selected through the parameter tr2
parameters tr1 and tr2 and the sample time through the parameter trc, • Other events: as well as the “Start” event, the log also records “Stop”
the unit starts recording the variables every trc minutes (sample time) for events (tr1=0 or tr2=0) and “Boot” (starting or restarting the controller)
a maximum period of 2 years each. After the second year, the controller • Log data format: the data is organised in columns: date (in standard
overwrites the oldest data saved. ISO 8601 format) , type of event, value of the variable specify as Src1
The variables log is available as a csv file via USB flash drive, which can be (first variable) and Src2 (second variable)
analysed in Excel or other widely-available programs.

29 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
Example: recording temperature probe Sv started on 2 April 2014 at as the message described above, during the update the message
17:19:49. The data were extracted by USB flash drive at 18:10 on the same “Software update” also scrolls on the second row.
day.
TIME EVENT Sv_Probe
Note: If for some reason the procedure is not successful, when
2014-04-02T17:19:49+00:00 Boot 0
2014-04-02T17:24:49+00:00 25,2
2014-04-02T17:29:49+00:00 25,0 exiting the menu, as well as the alarm icon on the display, the error
2014-04-02T17:34:49+00:00 24,6 message “SOF” will be displayed. In this case UltraCella retains the
2014-04-02T17:39:49+00:00 24,1 previously installed software. The error message will be cleared the next
2014-04-02T17:44:49+00:00 21,9 time the software is updated successfully or when restarting the
2014-04-02T17:49:49+00:00 18,8 controller.
2014-04-02T17:54:49+00:00 15,1
2014-04-02T17:59:49+00:00 12,7
2014-04-02T18:04:49+00:00 10,1
2014-04-02T18:09:49+00:00 7,3
Tab. 3.g
3.6 Message language selection
3.5.8 UltraCellasoftwareupdatefromLEDdisplayinterface
The only messages that change according to the selected language are
Starting from software release 1.5, the UltraCella software can also be those shown on the UltraCella Service terminal screens (PGDEWB0FZ*).
updated from the LED interface, as well as from the UltraCella Service
terminal.

The update.ap1 file needed to perform the update from the UltraCella
LED interface must only be supplied by CAREL personnel.

1. Create an “upgrade” folder in the main directory on the USB flash drive.
Copy the update.ap1 file to the new folder;
2. remove the bottom frame and plug in the USB flash drive. The red
and green LEDs on the side of the key will come on individually in
sequence to indicate that the unit recognises the USB flash drive;
3. press Prg and Set for 2 sec; the first menu is displayed: “HcP”;
4. press UP or DOWN until reaching the “SOF” menu item; Selecting the language
5. press SET to confirm the software update. The message “SOF” will flash
during the update; at the end, “SOF” will stop flashing, indicating 1. On the UltraCella Service terminal, access the multifunction menu by
the end of the procedure; if for some reason the procedure is not pressing the UP button;
2. The HACCP icon is displayed. Press UP or DOWN until reaching the“i”icon
successful, the alarm icon will be shown on the display; (information);
6. unplug the key; to exit the “SOF” menu, press PRG and/or SET 3. Press SET to access the language setting;
4. Select the desired language (in software release 1.6, the languages
available are Italian, English, German, French and Spanish) by
pressing UP or DOWN. Press SET to confirm. The change is effective
immediately;
5. Press ESC twice to exit the language selection menu and return to the
main screen
1 2

Note: The figure refers to navigation on models with single-row

display, WB000S%. On models with double row display, WB000D%, as well

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 30

 ENG
4. COMMISSIONING
4.1 First commissioning 4.3 Single digit display models cod.
After wiring the electrical connections and the power supply (see WB000S* commissioning
installation chapter), the operations required for commissioning the
UltraCella control system depend on the type of interface used. Refer to UltraCella with single row display
some parameters such as:
1. Set-point and differential;
2. Probes and digital inputs configuration; Multifunction menu
MENU

3. Selection of the type of defrost and fans operation;

4. Cold room light management. HELP

HACCP

Types of interfaces:
• board with LED display: parameters configuration is performed using
the display and the keyboard based on the procedure described in
chap.3 “parameters change”. Alternatively, you can connect the remote
graphic terminal “UltraCella Sevice Terminal” and enter the wizard
menu for first commissioning (wizard);
• USB memory key: put the control on OFF and load the programming
parameters from USB memory key (uPd command, UPLOAD, see
Chapter 3); Fig. 4.a
• supervisor: in order to facilitate the launch of a large number of controls
UltraCella using only the supervisor you can limit the operation of the
first commissioning to the serial address setting. The configuration is
postponed to a later time using the supervisor.
After the configuration you can enable the control of the cold room by
pressing the ON/OFF key.
1 2 1 2

1. First switch the controller OFF (press ON/OFF).

4.2 Parameterstobesetforthecommissioning
Par Description Categ. Def Min Max U.o.M.
St Set point CtL 0 r1 r2 °C/°F
rd Differential CtL 2.0 0.1 20 °C/°F
/P Type B1 to B3 Pro 0 0 2 - 1 2 1 2

/A2 B2 configuration Pro 1 0 3 -

/A3 B3 configuration Pro 0 0 5 - 2. Press Prg for 2 sec: the password 3. Press UP and enter the
/P4 Type B4 Pro 0 0 2 - prompt is displayed (PAS). password: 22.
/A4 B4 configuration Pro 0 0 4 -
/P5 Type B5 Pro 0 0 1 -
/A5 B5 configuration Pro 0 0 5 -
A5 Digital input configuration 2 (DI2) ALM 0 0 15 -
A9 Digital input configuration 3 (DI3) ALM 0 0 15 -
d0 Type of defrost dEF 0 0 3 -
dt1 End defrost temperature, main dEF 4.0 -50.0 200.0 °C/°F
evaporator 1 2 1 2
dP1 Maximum defrost duration dEF 30 1 250 min
dd Dripping time after defrost (fans dEF 2 0 30 min 4. Press Set: the first category is 5. Press Set: the first parameter is
off ) displayed: Pro (Probes). displayed: /21.
Fd Post dripping time (fans off ) Fan 1 0 30 min
F3 Evaporator fan during defrost Fan 1 0 1 -
0/1=on/off
c12 Compressor safety for door switch doL 5 0 5 min
0 = disable door management
d8d Compressor restart time for door doL 30 c12 240 min
switch
1 2
A3 Disable door microswitch doL 1 0 1 - 1 2

0=enabled
6. Press repeatedly UP to reach 7. Press Set to set the value of the
1=disabled
the parameter /P. parameter (see settings in the
tLi Light on with door open doL 120 0 240 min
A4 Light management doL 0 0 1 - parameter table).
0 = door switch + light key
1 = light key
c1 Minimum time between CmP 6 0 30 min
compressor starts
c2 Minimum compressor off time CmP 3 0 15 min
c3 Minimum compressor on time CmP 3 0 15 min
Tab. 4.a
1 2 1 2

8. Press UP to modify the value. 9. Press Set to confirm and return

to the parameter code. The new
value has now been saved on the
controller.

31 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG

1 2 1 2

10. Press UP to move to 11. Press Prg to return to the

parameters /A2.../ A5; make any parameter categories.
required settings.
5. Press Set: the second row of the 6. Press UP repeatedly until
display will scroll the code and reaching parameter /P. The second
description of the first parameter row of the display will scroll the
in the category: /21 – Probe1 code and description of the
meas. stab.; the first row of the parameter: /P – type B1 to B3; the
display will show the current first row of the display will show
value of the parameter the current value of the parameter
1 2

12. Press UP to move to category CtL and follow the previous steps to set St
and the following parameters.

4.4 Double digit display models cod.

WB000D* commissioning 7. Press Set and UP/DOWN to 8. Press Set to confirm. The new
set the desired value of the value entered is now saved on the
UltraCella with double row display parameter. controller.

9. Press UP to move to parameters 10. Press Prg to return to the

/A2…/A5; make any required categories of parameters.
settings .

Fig. 4.b

11. Press UP to move to category CtL (the second row scrolls the name of
the second category of parameters: Control) and follow the previous steps
to set St and the subsequent parameters, as shown in the previous table
and in the parameter table.
1. First switch the controller OFF (press ON/OFF).
2. Press Prg for 2 sec: the second row of the display will show “PASS”
(password required).

4. Press Set; the second row of

3. Press UP/DOWN to enter the the display will scroll the name of
password: 22. the first category of parameters:
Probes.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 32

 ENG
4.5 Commissioning with UltraCella Service
Terminal
H M
E E
L N
P Parameters Modification U

PRG Password: 1234 SET

+
ESC
H M
E E
L
P
Multifunction menu N
U

PRG SET

ESC
HACCP

UltraCella Fig. 4.g

with LED display
UltraCella Service terminal 2. To enter programming mode: Press Prg and enter the password: 1234

H M
E E
L Parameters Categ. 1/16 N
Fig. 4.c P U

1-Probes
If the UltraCella controller has never been configured, as soon as the PRG SET
2-Control
terminal is connected, the wizard is shown automatically. The Wizard 3-Compressor
menu can also be accessed to repeat the guided commissioning ESC

procedure before the first commissioning.

Fig. 4.h
3. Press DOWN until reaching the “Wizard” menu

H M
2 E E
1
L Parameters Categ. 16/16 N
P U

PRG 14-EVDice SET

15-Three-phases
16-Wizard
ESC

Fig. 4.d
Fig. 4.i
Remove the bottom faceplate and connect the UltraCella Service
Terminal to the controller. 4. Confirm by selecting Set.

H M
E E
L
P Wizard N
U
Do you want to use the
4.5.1 First start - up PRG Wizard to configure
SET
When starting for the first time, once the Service Tool is connected, the the cold room ?
wizard is shown automatically. Select the desired language and then ESC
YES
answer the questions to set the other parameters.

H
E
M
E
Fig. 4.j
L Wizard N
P U
5. Press Up and SET to enter the guided commissioning procedure.
PRG Language: English SET
Up/Down: Choose language
Prg/Set: 1st question 4.6 Main function commissioning
ESC

4.6.1 Set-point and differential

Fig. 4.e The reference output is the compressor output (CMP). The set point
and differential determine the compressor activation and deactivation
temperatures. The control probe is the virtual probe Sv. At start-up it
corresponds to probe B1. If the temperature inside the cold room is not
4.5.2 Repeated commissioning procedure uniform the control can be set (by placing /4> 0) to regulate on a “virtual”
probe obtained from the average of two measurement points (probes
The commissioning procedure can be repeated by accessing the Wizard
B1 and B2).
menu.
CMP
ON
H M
E E
L
P 03/12/13 Setpoint N
U
17:52:30 0.0 °C OFF
PRG
Sv
SET
rd
OFF St
ESC

Fig. 4.k
Key
Fig. 4.f St Set point
Sv Virtual probe
1.Switch the controller OFF (press DOWN and select the On/Off icon; rd Differential
press Set twice and then UP to switch the controller OFF; press Esc twice CMP Compressor
to exit) Note: see par. "6.3 Set point" for the options related to the
regulation of the control set point

33 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
4.6.2 Probes configuration Par. Description Def Min Max U.o.M.
The UltraCella controls have a maximum of 5 analog inputs, of which /4L Probe 4 minimum value (only for 0...10V 0 -50,0 /4H -
3 can be configured as temperature probes (NTC probes, NTC high input)
temperature probes, PT1000), the fourth as temperature probe or input 0 /4H Probe 4 maximum value (only for 0...10V 100,0 /4L 200,0 -
input)
... 10 V, the fifth can be configured as input 4 ... 20 mA or 0...5 Vrat.
/5L Probe 5 minimum value 0,0 -50,0 /5H -
Analogue Inputs Type /5H Probe 5 maximum value 100,0 /5L 999 -
B1 NTC10 kΩ a 25°C, range -50T90°C,
B2 NTC extended range, NTC50 kΩ a 25°C, range 0T150°C; Example: if input B5 is connected to a pressure sensor with 4 to 20 mA
B3 PT1000, 1000 Ω a 0°C, range -50T90°C output and a range of -1 to 9.3 bars, set
B4 NTC10 kΩ a 25°C, range -50T90°C, - /5L = -1.0
NTC extended range, NTC50 kΩ a 25°C, range 0T150°C - /5H = 9.3
0…10 V In this case, when the probe reads a value of 12 mA, the value associated
B5 4…20 mA
with the reading of B5 will be 4.1 (middle of the scale).
0...5Vrat
Tab. 4.b

Below the parameters with the selection: 4.6.4 Probes reading correction
The values read by the probes can be corrected by adding/removing an
Par. Description Def Min Max U.o.M. offset from the measure with the parameters /c1, ..., /c5.
/P Type B1 to B3 0 0 2 -
0 = NTC Standard Range -50T90°C Par. Description Def Min Max U.o.M.
1 = NTC Enhanced Range 0T150°C /c1 Offset B1 0 -20.0 20.0 °C/°F
2 = PT1000 /c2 Offset B2 0 -20.0 20.0 °C/°F
/c3 Offset B3 0 -20.0 20.0 °C/°F
/P4 Type B4 0 0 2 - /c4 Offset B4 0 -20.0 20.0 °C/°F/%rH
0 = NTC Standard Range -50T90°C /c5 Offset B5 0 -20.0 20.0 °C/°F/%rH/bar/psi
1 = NTC Enhanced Range 0T150°C
2 = 0 to 10 V The offset may need to comply with HACCP requirements. In this case,
/P5 Type B5 0 0 1 -
the offset should be calculated using a calibrated instrument. Setting
0 = 4 to 20 mA
these parameters affects the measurement and the value shown on the
1 = 0 to 5 Vrat
display, and consequently may not be allowed. If in doubt, contact the
food safety manager or site manager.

4.6.3 Probes function assignment B1, B2, B3, B4, B5 T2

The control, inside the cold room, can use the probes:
• outlet;
• intake;
• defrost, placed in the evaporator, preferably where the ice resides most;
• condenser, used to protect the compressor due to high discharge
A

temperature, associated with fowling of the condenser or fan failure. T1

Probe B1 is configured as environment probe and its function cannot be min max
changed. Fig. 4.l
Par. Description Def Min Max U.o.M. Key
/A2 Configuration B2 1 0 3 - T1 Temperature measured by the probe
0 Absent T2 Temperature measured by the probe after offset correction
1 Defrost probe 1 (Sd1) A Offset value
2 Intake probe (Sr) min, max Measurement range
3 Generic temperature probe 2
/A3 Configuration B3 0 0 5 -
0 Absent
1 Defrost probe 2 (Sd2) HACCP - CAUTION
2 Cond. probe (Sc) The modification of these parameters, influencing the measurement and
3 Defrost probe 1 (Sd1) display, may not be allowed in some applications or might require special
4 Ambient probe (SA) approval because it may affect the operation of HACCP systems.
5 Generic temperature probe 3 If in doubt, consult the person in charge of food safety or the manager
/A4 Configuration B4 0 0 4 - of the plant.
0 Absent
1 Ambient temperature probe (SA)
2 Humidity probe
3 Generic temperature probe 4
4 Generic humidity probe 4 4.6.5 Digital inputs
/A5 Configuration B5 0 0 5 -
0 Absent
1 Humidity probe Note: the digital input 1 (DI1) is suited for door switch and is not
2 Generic temperature probe 5 programmable.
3 Generic humidity probe 5
4 Generic pressure probe 5 If the door switch is not used, input DI1 can be disabled, and will no
5 Condensing pressure probe (Scp)
longer be available for other functions, by setting A3=1 (default value)

Par. Description Def Min Max U.o.M.

A3 Disable door microswitch 1 0 1 -
For probe B4, if configured as a 0 to 10 V input (/P4=2) and for probe B5, 0= enabled
the logical control values corresponding to the physical end scale values 1= disabled
can be configured.
If A3=0 and the door microswitch is not connected, the controller will
activate the "door open" icon. To prevent incorrect messages being

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 34

 ENG
displayed, set A3=1 or short-circuit pin 21 (DI1) to one of the GND pins. Note: this function is useful to prevent defrosts on the units
accessible by the public during opening times.
You can link multiple contacts to multifunction digital inputs to activate
various functions, such as alarm, enable / start defrost, low pressure, etc..
Caution: in order to ensure the safety of the unit in the event of 4 = Start defrost from external contact
serious alarms, all the electromechanical safety devices required
to guarantee correct operation must be fitted on the unit. Application: this feature is useful in case you need to perform synchronized
defrost across multiple units or otherwise manually controlled by an
external contact. To perform the defrosts, connect a cyclical, mechanical
Operation of the digital inputs DI2, DI3 or electronic timer to the digital input. You can connect multiple units
at the same timer and set different values for the parameter d5 (defrost
PARAMETERS A5, A9 delay from multifunction input) to avoid simultaneous defrosts.

Selection Contacts
OPEN CLOSE ON
Timer
OFF
0 = Not active - -
1 = Immediate external alarm active not active ON UNIT 1
2 = Do not select - - Defrost
3 = Enable defrost not enabled enabled
4 = Start defrost not active active OFF
5 = Do not select - -
ON UNIT 2
6= Remote On/Off OFF ON
7 = Do not select - - Defrost
8 = Low pressure switch low pressure status normal status
9 = Do not select - - OFF
10 = Do not select - - UNIT 3
ON
11 = Do not select - -
12 = AUX activation deactivated activated Defrost
13 = Do not select - -
OFF
14 = Continuous cycle activation contact opening contact closing
(deactivation) (activation) t
15 = Alarm from generic function active / not active active / not active dP(1) dP(2) dP(3)
Tab. 4.c d5(2)
d5(3)
Below are indicated the parameters used to explain the selections for A5
and A9. Fig. 4.m
Key
1 = Immediate external alarm dP Maximum defrost duration
UNIT 1…3 Unit 1…3
Application: external alarm that requires immediate activation (for d5 Defrost delay form digital input
example, high pressure alarm or compressor thermal overload). The t Time
activation of the alarm:
1. • shows the message on the display (IA);
• activates the buzzer, if enabled; 5 = Do not select
• activates the alarm relay, if selected;
2. involves the following actions on the actuators: 6=On/Off remote
• compressor: operates depending on the values assigned to
parameter A6 (stop compressor on external alarm). The digital input can also be programmed as a remote ON/OFF switch.
• fans: continue to operate according to the fan parameters (F). When the control is set to OFF:
• the temperature is displayed alternately with the message “OFF”, the
Note: internal timer relative to the parameter dI is updated. If dI expires when
the unit is OFF, a defrost is performed when the unit is switched on
• when stopping the compressor, the minimum ON time (c3) is ignored. again;
• if more than 1 input is configured on immediate alarm, the alarm is • the auxiliary relays remain active set as an auxiliary output and light,
generated when one of the inputs is opened. the other auxiliary outputs are off;
• the buzzer and the alarm relay are off;
2 = Do not select • the control does not perform the control functions, defrosts, continuous
cycle, temperature alarm signalling and all the other functions;
3 = Enable defrost • the compressor protection times are respected.
Application: Any defrost request arriving when the contact is open will At control restart, all functions are reactivated, except:
remain pending until the contact closes. • defrost at start-up;
• compressor and fan delay at start-up.
A5/ A9 = 3
Contacts Defrost
Note: The ON/OFF from external digital input has priority over the
Open Not enabled keypad and the supervisor.
Closed Enabled (defrost start is still determined by the control)
Close with active when the digital input is opened, the defrost is
defrost immediately stopped and the unit restarts normal 7 = Do not select
operation (without performing the dripping or post-
dripping phases). The LED starts flashing to indicate 8 = Low pressure switch
that the defrost request is pending, waiting for the next
enabling signal (closing of the contact), when the defrost By setting A5/A9=8 you can manage the low pressure switch. The low
will be performed completely. pressure alarm “LP” is signalled when the low pressure switch is triggered:
Tab. 4.d • during normal regulation, with active compressor and pump down
function is disabled (c7=0)
35 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
• with pump-down function enabled (c7 >0), if the pump down valve is 4.6.8 Door opening
opened and the compressor is active. If the door is left open, the signalling control is made via the door
The low pressure alarm signal is delayed by the time set for parameter A7. switch (if A3=1, digital input DI1, already configured as the door switch,
The low pressure alarm ‘LP’ stops the compressor. is disabled). When the door is open, the evaporator fans are turned off
if configured at fixed speed (F0=0,1), otherwise operate at minimum
speed defined by parameter F7 (if F7<50) if set as variable speed fans
(F0= 2); the compressor continues to operate for the time c12, then turns
 off. Once passed the period of time d8d from door opening, compressor
 and evaporator fans are running again and the error “dor” is displayed.
Par. Description Def Min Max U.o.M.
1 2 1 2
c12 Compressor safety time, door switch 5 0 5 min
0 = disabled door management
d8d Compressor restart time for door switch 30 c12 240 min

9, 10, 11 = Do not select Special cases refer figure 4.n and 4.o:
• to disable door alarm, set d8d =0. If d8d = 0, c12 is also considered =0;
12 = Auxiliary output • to keep only phase 2 (figure), in which the compressor is on, and to
eliminate phase 3 in which the compressor/ evaporator fan is off, set
Setting H1/H5 = 2 the corresponding output AUX1/ AUX2 is activated d8d=c12;
by the key AUX1/ AUX2 or from DI if set. Besides, it is possible to use • to keep only phase 3 (figure), c12=0;
alternatively one digital input DI2 or DI3 (set A5 or A9=12) to drive output • during phase 3 the compressor may be on if:
AUX2 or AUX3. In this case the key and the digital input have the same 1. pump down is activated;
priority as regards the switch on. 2. hot gas defrost is activated.
13 = Do not select
Note: If the door switch digital input DI1 is disabled (A3=1):
14 = Continuous cycle activation • Parameters C12 and d8d have no meaning, as the controller
Activation: passage of the contact from opened to closed; cannot know whether the door is open or closed
Deactivation: passage of the contact from closed to opened. • The door open icon will always be off

15 = Alarm from generic function Compressor on Compressor off

Digital inputs DI2 and DI3 can be associated with special alarms, using before door opening before door opening
the generic functions, and can be activated with the input open or closed open open
(see the paragraph on Generic functions). Door Door
switch switch
close close
4.6.6 Type of defrost ON ON
UltraCella allows you to manage the following types of defrost, depending Evaporator Evaporator
on parameter d0: fan fan
0. electric heater defrost by temperature; OFF OFF
1. hot gas defrost by temperature;
ON ON
2. electric heater defrost by time;
3 hot gas defrost by time. CMP CMP

For further explanations please see chap. 6. OFF OFF

Par. Description Def Min Max U.o.M. ON ON

d0 Type of defrost 0 0 3 - Door Door
0 heater by temperature. alarm alarm
1 2 3 4 1 2 3 4
1 hot gas by temperature OFF
OFF
2 heater by time c12
t c12
t
3 hot gas by time d8d
d8d
dt1 End of defrost temperature, main 4.0 -50.0 200.0 °C/°F
evaporator Fig. 4.n Fig. 4.o
dP1 Maximum defrost duration 30 1 250 min
Key
t Time
Door_sw door switch
Evap_fan Evaporator fan
4.6.7 Evaporator Fans CMP Compressor
During the dripping periods (parameter dd > 0) and post-dripping periods Dor alarm Door alarm “dor”
(parameter Fd > 0) the evaporator fans are always off. This is useful to
allow the evaporator to return to normal temperature after defrost. There Note: to render the time settings operational, the control must
is the possibility to force the start of the evaporator fans during control restart. Otherwise, the settings will be used only at the next use,
(parameter F2) and during defrost (parameter F3). See chap. 6 when the inner timers are set.
Par. Description Def Min Max U.o.M.
dd Dripping time after defrost (fans off ) 2 0 30 min
F2 Fan activation time with compressor OFF 30 0 60 - 4.6.9 Compressor management
F3 Evaporator fan during defrost 1 0 1 -
0/1=on/off • c1 determines the minimum time between two consecutive starts of
Fd Post dripping time (fans off ) 1 0 30 min the compressor;
• c2 sets the minimum turn off time for the compressor.
• c3 sets the minimum running time for the compressor.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 36

 ENG
Par. Description Def Min Max U.o.M. Key
c1 Minimum time between two successive 6 0 30 min Light_k Light key
starts of the compressor Li Light
c2 Compressor minimum switch-off time 3 0 15 min Door_sw Door switch
c3 Compressor minimum switch-on time 3 0 15 min tLi Light turn off delay
t Time
c1
c3 c2

ON

Step1
4.8 Other configuration parameters
The configuration parameters must be set during the commissioning of
OFF the controller and concern:
ON
• date/time set;
• measurement stability of the analogue probes;
Step2 • display of the decimal point on control;
• serial address for monitoring network connection;
OFF
• ithe type of protocol on the BMS serial port for connection to the
Power_ON
t supervisor network
c0 c11 • temperature (°C / °F) and pressure (bar/psi) measurement unit
• disabling of keyboard, keys and buzzer;
Fig. 4.p
• display view during defrost.
Note: c2 parameter used to ensure the balance of the pressure
after the compressor stop and to avoid blocking at the next Date/ time set
reboot of those compressors that do not have sufficient starting torque. See example 2 in chap.3.

Analogue probes measuring stability

It defines the filter coefficient used to stabilize the temperature
measurement. Low values assigned to this parameter allow a prompt
4.7 Light management response of the sensor to temperature variations, but the reading
The light can be managed: becomes more sensitive to disturbance. High values slow down the
• from door switch (if A3=0) and/or light key; response, but guarantee greater immunity to disturbance, that is, a more
• only from light key. stable and more precise reading.
Below are indicated the involved parameters. Par. Description Def Min Max U.o.M.
/21 Stability measuring probe 1 4 0 9 -
Par. Description Def Min Max U.o.M.
/22 Stability measuring probe 2 4 0 9 -
tLi Light on with door open 120 0 240 min /23 Stability measuring probe 3 4 0 9 -
A4 Light management 0 0 1 - /24 Stability measuring probe 4 4 0 9 -
0 Door switch + light key /25 Stability measuring probe 5 4 0 9 -
1 Light key
Display view
Note: if the control is OFF, the light output is controlled only by
On models with single row display, P/Ns WB000S*, it is possible to show a
the light key. If the control is set to ON, the light is controlled by a
single characteristic, selectable through /t1 parameter.
door switch + light key or just light key according to the setting of the
On models with two rows, P/Ns WB000D*, and on the UltraCella Service
parameter A4.
terminal, it is possible to show two different characteristics, the first
selectable through /t1 parameter, and the second through /t2 parameter.

4.7.1 Door switch + light key Par. Description Def Min Max U.o.M.
/t1 Display variable 1 1 0 13 -
If A4=1 the light is on/off only using the light key. The open/closed status 0 None 7 B1
of the door is ignored. If A4=0, when the cold room door is opened, the 1 Virtual probe 8 B2
light is always on. When the door is closed, the light can be turned on or 2 Outlet probe 9 B3
off using the light key. Once turned on, the light will automatically turn 3 Intake probe 10 B4
off after the time set in parameter tLi. 4 Defrost probe 1 11 B5
5 Defrost probe 2 12 Sc
6 Set point 13 Variable speed
LIGHT CONTROL FROM DOOR SWITCH AND LIGHT KEY condenser
fans set point
ON
A4=0 /t2 Display variable 2 6 0 23 -
0 None 12 rd
Light_K 1 Virtual probe 13 superheat (EVD
EVO)
OFF 2 Outlet probe 14 valve opening
% (EVD EVO)
OP
3 Intake probe 15 valve opening
Door_sw step (EVD EVO)
4 Defrost probe 1 16 Sc
CL 5 Defrost probe 2 17 Sd1 (3PH mod.)
6 Set point 18 Sd2 (3PH mod.)
ON 7 B1 19 Sc (3PH mod.)
8 B2 20 Variable speed
Li condenser fans
set point
OFF
9 B3 21 Superheat
(EVDice)
t 10 B4 22 Valve opening
tLi tLi
% (EVDice)
11 B5 23 Step valve
Fig. 4.q opening
(EVDice)
37 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
Serial address (parameter H0) 4.9 Ultra EVD EVO module commissioning
H0 assigns an address to check for serial connection to a supervision
WM00ENNI00: Connect UltraCella to the EVD module via serial, as shown
system and / or remote assistance.
in the wiring diagram in Figure 2.k, and refer to the following parameter
Par. Description Def Min Max U.o.M. table for configuration of the EVD EVO driver. The module will become
H0 Serial Address 193 0 247 - active when enabled by UltraCella, setting P1=1.

Starting from software release 1.5, both CAREL and Modbus protocols Par. Description Def Min Max U.o.M.
are available on the BMS serial port, selected by parameter H7. P1 Enable communication with EVD EVO 0 0 1 -
module
Note: H0 maximum value is 207 for CAREL protocol and 247 for 1 = EVD EVO module enabled
Modbus protocol.
WM00ENSI00 & WM00ENS000:
Par. Description Def Min Max U.o.M. 1. Using the EVD EVO display to configure the driver
H7 BMS serial protocol 0 0 1 -
Connect an auxiliary output on UltraCella (AUX1 or AUX2) electrically to
0= CAREL protocol
digital input DI1 on the EVD EVO and set the parameters as follows:
1= Modbus protocol

Starting from software release 1.7, the baud rate, stop bits and parity of • H1=7 (for AUX1) or H5=7 (for AUX2) -> delayed second compressor
the BMS port can be set using parameters H10, H11 and H12; the data bits • C11=0 -> second compressor activation delay = 0
setting on the other hand remains fixed at 8.
Par. Description Def Min Max U.o.M.
Par. Descrizione Def Min Max UoM H1 AUX1 output configuration 1 0 17 -
H10 BMS baud rate bit/s 4 0 9 - 7 = Delayed compressor
0 1200 5 38400 H5 AUX2 output configuration 1 0 17 -
1 2400 6 57600 7 = Delayed compressor
2 4800 7 76800 C11 Second compressor start delay 4 0 250 sec
3 9600 8 115200 0 = instant start with main compressor
4 19200 9 375000 output
H11 BMS stop bits 2 1 2 - In this way, the auxiliary output will be configured as a voltage-free contact
1 1 stop bit to control the compressor, suitable to be connected to digital input DI1
2 2 stop bits on the EVD EVO driver. No configuration is required on UltraCella.
H12 BMS parity 0 0 2 -
2. Configuring the EVD EVO driver from UltraCella
1 odd
Connect UltraCella to the EVD EVO module via serial, as shown in the
2 even
wiring diagram in Figure 2.k, and refer to the following parameter table
for configuration of the EVD EVO driver. The module will become active
Note: to make the changes active, switch the unit off and on
when enabled by UltraCella, setting P1=1.
again.
If connected via serial, the driver parameters can only be displayed (not
modified) on the EVD EVO local display. Once the driver has been enabled
Temperature unit of measure and decimal point display (parameter P1=1), its parameter settings will be sent by UltraCella, in
The control allows: accordance with the parameter table below (only modifiable from
• choosing the temperature measuring unit between Celsius (°C) and UltraCella); any parameters previously configured on the EVD EVO display
Fahrenheit (° F) degrees; will be overwritten.
• to enable/disable the display of the decimal point and buzzer.
Par. Description Def Min Max U.o.M.
Par. Description Def Min Max U.o.M. P1 Enable communication with EVD EVO 1 0 1 -
/5t Temperature unit of measure 0 0 1 - module
0/1 = °C / °F 1 = EVD EVO module enabled
/SP Pressure unit of measure 0 0 1 -
0/1 = bar / psi
/6 Display decimal point 0 0 1 - EVD EVO parameter table
0/1 = yes/no The following parameters corresponding to the EVD EVO driver can be
H4 Buzzer 0 0 1 - configured from UltraCella
0/1 = enabled/disabled Category: EVO
Par. Description Def Min Max U.o.M.
Disable keypad P1 Enable communication with EVD EVO 0 0 1 -
You can inhibit some functions relating to the use of the keypad, for module 0/1=disabled/enabled
example, the modification of the parameters and the set point if the unit P1t S1 probe type 0 0 3 -
is accessible to the public 0 RAZ. 0-5V 2 4 to 20mA REMOTE
Par. Description Def Min Max U.o.M. 1 4 to 20mA 3 4 to 20mA EXTERNAL
H6 Terminal keys block configuration 0 0 255 - P1M Max value of S1 probe 12,8 -20 200 bar/psi
0 = all keys enabled. P1n Min value of S1 probe -1 -20 200 Bar/psi
255 = all keys disabled

Configuration table
FUNCTION par. H6
Set-point modification 1
Defrost 2
- 4
AUX1output 8
PRG+SET (menu) 16
AUX2 output 32
On/Off management 64
Light management 128
Tab. 4.e
Example: to disable the activation functions of the outputs AUX1 and
AUX2, set H6 = 8+32 = 40.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 38

 ENG
PVt Valve type 1 1 22 - parameters will be those set on EVDice, and UltraCella will generate a
new signature. Proceed as follows:
1 Carel exv 12 Sporlan seh 100
2 Alco ex4 13 Sporlan seh 175
1. Confirm that the EVDice is present by setting IPE=1 (communication
3 Alco ex5 14 Danfoss ets 12.5
with EVDice enabled), or by answering “yes” to a specific question in
- 25b the wizard on the UltraCella Service terminal; UltraCella will sign the
4 Alco ex6 15 Danfoss ets 50b EVDice so as to create the controller-driver combination;
5 Alco ex7 16 Danfoss ets 100b 2. The IEC (EVDice configuration error) alarm will be activated and the
6 Alco ex8 17 Danfoss ets 250 controller (and the compressor) will stop (UltraCella forces parameter
330hz CAREL
recommended ICG=0, EVDice not enabled for control). Configure the EVDice
7 Alco ex8 18 Danfoss ets 400 parameters based on the application, either using the wizard, or
500hz alco parameter-by-parameter on the LED display interface;
specification
3. Once all of the required EVDice parameters have been configured, set
8 Sporlan sei 19 two CAREL exv
0.5-11 connected together ICG=1 to activate control. Setting ICG=1 also resets the IEC alarm.
9 Sporlan ser 20 Sporlan ser(i) g, j, k
1.5-20 Replacing EVDice due to a fault / other causes:
10 Sporlan sei 30 21 Danfoss ccm 10- 1. UltraCella will have a signature other than 0 (as it has been previously
20-30
configured to manage an EVDice driver), while the EVDice will have a
11 Sporlan sei 50 22 Danfoss ccm 40
different signature from the one saved on UltraCella (either 0 if new,
PH Refrigerant type 3 1 25 -
or a number other than 0 if originating from another installation). In
1 R22 10 R717 18 R423A this case, the initially active parameters will be those set on UltraCella
2 R134a 11 R744 19 R407A (the parameters on UltraCella corresponding to the EVDice driver will
3 R404A 12 R728 20 R427A be copied to the EVDice). Proceed as follows:
4 R407C 13 R1270 21 R245Fa • The IEM alarm (EVDice error mismatch) is active to warn the user that
5 R410A 14 R417A 22 R407F an element in the system has been changed. If necessary, modify the
6 R507A 15 R422D 23 R32 EVDice parameters based on the application, either using the wizard, or
7 R290 16 R413A 24 HTR01 parameter-by-parameter on the LED display interface;
8 R600 17 R422A 25 HTR02 • The controller is will active even when the IEM alarm is active; to
9 R600a
disable the alarm, press on the UltraCella LED display.
PrE Main regulation type 2 1 4 - 2. The signature on UltraCella will be equal to 0 (as it is new or has not
1 centralized cabinet cold room been previously configured to communicate with an EVDice driver),
2 self contained cabinetcold room while EVDice will have a signature (signature other than 0). In this
3 perturbated cabinet cold room case, the initially active parameters will be those set on EVDice (the
4 subcritical CO2 cabinet/cold room parameters corresponding to the EVDice driver will be copied to
P0 EVD Modbus address 198 1 247 - UltraCella). The case is identical to a new installation / new system:
P3 Superheat setpoint 10 -72 324 K • Confirm that the EVDice is present by setting IPE=1 (communication
P4 Proportional gain 15 0 800 - with EVDice enabled), or by answering “yes” to a specific question in the
P5 Integral time 150 0 999 sec wizard on the UltraCella Service terminal; UltraCella will sign the EVDice
P6 Derivative time 2 0 800 sec so as to create the controller-driver combination;
P7 LowSH: threshold low superheat 3 -72 324 K • The IEC (EVDice configuration error) alarm will be activated and the
P8 Low Superheat protection integral time 600 0 800 sec controller (and the compressor) will stop (UltraCella forces parameter
P9 LowSH: low superheat alarm delay 600 0 999 sec ICG=0, EVDice not enabled for control). Configure the EVDice parameters
PL1 LOP: threshold for low temp. of evapor. -50 -60 200 °C/°F based on the application, either using the wizard, or parameter-by-
PL2 LOP: integral time 600 0 800 sec
parameter on the LED display interface;
PL3 LOP: low evaporation temperature alarm delay 600 0 999 sec
cP1 Open valve startup, Percentage 50 0 100 %
• Once all of the required EVDice parameters have been configured, set
PM1 MOP: threshold for low temp. of evapor. 50 -60 200 °C/°F ICG=1 to activate control. Setting ICG=1 also resets the IEC alarm.
PM2 MOP: integral time 600 0 800 sec
PM3 MOP: low evaporation temp. alarm delay 10 0 999 sec Replacing UltraCella due to a fault / other causes:
Pdd Post defrost delay, only for single driver 10 0 60 min The signature on UltraCella will be equal to 0 (as it is new or has not been
PSb Valve position in stand-by 0 0 100 step previously configured to communicate with an EVDice driver), while
PMP Enable manual positioning 0 0 1 - EVDice will have a signature (signature other than 0). In this case, the
PMu Manual valve positioning 0 0 999 step initially active parameters will be those set on EVDice (the parameters
Pnr Reset EVD setting 0 -> 1 Reset all EVD EVO 0 0 1 - corresponding to the EVDice driver will be copied to UltraCella). The case
parameters is identical to a new installation / new system.

Par. Descrizione Def Min Max UoM

4.10 EVDice commissioning IPE Enable EVDice communication 0 0 1 -
0/1 = disabled / enabled
Connect UltraCella to the EVDice driver via the serial line according to the
ICG Enable EVDice control 0 0 1 -
wiring diagram shown in Figure 2.o, and refer to the parameter table 4.e 0/1 = disabled / enabled
below for configuration of the EVDice driver.
UltraCella software release 1.7 features new EVDice driver management Note: when IPE=0 (communication with EVDice disabled), the
functions: only parameters visible on the UltraCella built-in LED display are:
• Possibility to configure the EVDice parameters on the UltraCella user IPE, IrE (EVDice operating mode), IP3 (superheat set point), PH (type of
interface (built-in LED display or UltraCella Service terminal) and/or on refrigerant) and In1 (EVDice serial address from UltraCella)
the local EVDice LED display user interface. Note: the signature on EVDice can be set to zero using the reset
• EVDice custom configuration protection by signature: as soon as procedure on the built-in LED interface (see EVDice manual
communication is established, UltraCella “signs” EVDice by writing a +0300037EN)
random number between 1 and 65000 to a register on the driver. This Note: the above are valid for EVDice firmware release 1.4;
allows unique identification of: UltraCella software release 1.7 in any case maintains compatibility
- EVDice drivers that have been previously configured with EVDice drivers featuring previous firmware releases. In particular, the
- “new” EVDice drivers (e.g. replaced due to a fault) IEC and IEM alarms will be always disabled, parameters IPE and ICG will
There are three possible cases: have always the same value and UltraCella will not generate any signature
Note: in UltraCella software release 1.7, the EVDice firmware
New installation / New system / EVDice installed following installation: release is read-only when parameter IPE=1 (communication with
in this case, the signature on UltraCella will initially be 0 -> the active EVDice enabled)
39 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
EVD ICE parameter table
The following parameters correspond to the EVD ICE driver, and are
configured on UltraCella.
Category: ICE

Parameter name Description Def Min Max U.o.M. Type Parameter Present on Present
on EVD ICE name on UltraCella in wizard
UltraCella Service pGD (UltraCella
(LED display) Service pGD)
- Enable EVD ICE 0 0 1 - Advanced IPE  
/1 = not enabled/ enabled
Operating mode 1=Multiplexed cabinet/cold room 1 1 6 - Initial IrE  
2=Air-conditioner/chiller with plate heat (modes 2, configuration
exchanger 3, 4, 5 and 6
3=Air-conditioner/chiller with tube can only be
bundle heat exchanger selected on
4=Air-conditioner/chiller with finned UltraCella
coil heat exchanger service
5=Reserved
pGD)
6=Reserved
Superheat Superheat set point 11 C1 99 K Initial IP3  
configuration
Type of gas 1=R22 2=R134a 3=R404A 3 1 23 - Initial PH  
4=R407C 5=R410A 6=R507A configuration
7=R290 8=R600 9=R600a
10=R717 11=R744 12=R728
13=R1270 14=R417A 15=R422D
16=R413A 17=R422A 18=R423A
19=R407A 20=R427A 21=R245FA
22=R407F 23=R32
S1 Type of probe S1 3 1 11 - Advanced IS1  
1=-1 to 4.2 barg
2=0.4 to 9.3 barg
3=-1 to 9.3 barg
4=0 to 17.3 barg
5=0.85 to 34.2 barg
6=0 to 34.5 barg
7=0 to 45 barg
8=-1 to 12.8 barg
9=0 to 20.7 barg
10=1.86 to 43.0 barg
11 = Reserved
CP PID: proportional gain 15 0 800 - Advanced ICP  -
ti PID: integral time 150 0 999 sec Advanced Iti  -
C1 LowSH protection: threshold 5 -9 IP3 °C/°F Advanced IC1  -
C2 LowSH protection: integral time 15 0 800 sec Advanced IC2  -
C3 LOP protection: threshold -50 -121 C5 °C/°F Advanced IC3  -
C4 LOP protection: integral time 0 0 800 sec Advanced IC4  -
C5 MOP protection: threshold 50 C3 392 °C/°F Advanced IC5  -
C6 MOP protection: integral time 20 0 800 sec Advanced IC6  -
C7 MOP protection: disable threshold 30 -121 200 °C/°F Advanced IC7  -
C8 Low suction temperature alarm threshold -121 -392 200 °C/°F Advanced IC8  -
IA Enable operating mode modification 0 0 1 - Advanced IIA  -
0/1 = enabled/not enabled
U1 Enable manual valve positioning 0 0 1 - Advanced IU1  -
0/1 = enabled/not enabled
U2 Manual valve position 0 0 999 step Advanced IU2  -
U3 Valve control steps: 1/2 = 480/960 step 1 1 2 - Advanced IU3  
U4 Valve opening at start (evaporator/valve 50 0 100 % Advanced IU4  -
capacity ratio)
n1 Serial address 99 1 99 - Advanced In1  
- Enable EVD ICE regulation 0 0 1 - Advanced ICG  
0/1 = not enabled/ enabled

Note: as EVD ICE has a two digit display, when its parameters are
displayed on UltraCella, the letter “I” has been added to every
parameter code: e.g. S1 -> IS1
Note: all EVD ICE parameters are visible both on the LED user
interface and on the UltraCella Service terminal (pGD).

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 40

 ENG
4.11 Ultra 3Ph Evaporator module 4.11.2 Parameters (UltraCella)
commissioning UltraCella has a subset of parameters dedicated to Ultra 3PH Evaporator
Ultra 3PH Evaporator module has to be configured by UltraCella. module configuration.
1. Please make sure that, inside Ultra 3PH Evaporator module, dip-switches Category: 3PH
of I/O expansion are set as per following figure (default setting):
Par Description Def Min Max UOM
cH1 3PH module serial address 15 1 247 -
cH2 3PH module offset serial address 0 0 232 -
cH3 Type of three phase module 0 0 1 -
0 = Evaporator
1 = Full
cA1 Sd1 probe connection 0 0 1 -
0 = in UltraCella
1 = in 3PH module
cA2 Sd2 probe connection 0 0 1 -
Address Ext Baud Prot 0 = in UltraCella
1 = in 3PH module
cA3 Sc probe connection 0 0 1 -
1 9 (Full module only)
2 10
3 11 0 = in UltraCella
4 12 19.2 K 1 = in 3PH module
5 13 9.6 K
6 14 cEn Enable 3PH mod. 0 0 1 -
7 15 with offset 38.4 K CAREL
8 no offset 57.6 K Modbus 0 = disable
1 = enable
ON
OFF
Address Ext. Baud Prot 4.11.3 Function
Fig. 4.r Ultra 3PH Evaporator Module has to be combined with UltraCella controls
which corresponds to following configuration: (P/Ns WB000S% or WB000D%). Module has inside high power actuators
• Address = 15 to handle directly three-phase loads of the evaporator, but logic and
• No offset regulation algorithms are inside UltraCella.
• Baudrate = 19200bit/sec In the table below details of where probes and loads can be connected.
• Protocol = Modbus
2. In UltraCella, access to parameter category “3PH” Note:
3. Make sure that first two parameters are set as follows (Carel default • Although three-phase loads have to be physically connected to Ultra
setting): 3PH Evaporator module, UltraCella maintains its standard configuration
• cH1 = 15 (Address) of relays.
• cH2 = 0 (Offset)
Connected
4. For 3PH Evaporator module, set (Carel default setting) UltraCella Ultra 3PH Evaporator
• cH3 = 0 Input module
Ambient probe  -
5. If defrost probe and auxiliary evaporator defrost probe have to be cA1 = 0
connected to Ultra 3PH Evaporator module, set:  -
• cA1 = 1 Defrost probe Sd1
cA1 = 1
• cA2 = 1 - 
For Ultra 3PH Evaporator module, don’t consider parameter cA3 cA2 = 0
Defrost probe auxiliary  -
6. Enable 3PH Evaporator module by setting: evaporator Sd2 cA2 = 1
• cEn = 1 - 

Ultra 3PH Evaporator

Note: to ensure the communication between UltraCella and the Output UltraCella module
expansion module, the I/O expansion network address and parameter Compressor command /
cH1 on UltraCella must be set to the same value (default 15).  
Condensing unit enabling
(1PH) (1PH)
/ Solenoid valve
 
Important: Defrost heaters
(1PH) (3PH)
This setting of the dipswitches on the I/O expansion (corresponding to  
Evaporator fans
serial address 15) is active starting from November 2015 and guarantees (1PH) (3PH)
“plug & play” communication with UltraCella controllers running software 
Light -
release 1.7 (default value cH1=15). (1PH)
Expansion modules manufactured prior to November 2015 have the  
AUX1
(1PH) (1PH)
default address setting as 1 (different dipswitch configuration than

shown in the figure). UltraCella controllers running a software release AUX2 -
(1PH)
lower than 1.7 are set with cH1=1 by default. In some cases, then, the two Tab. 4.f
configurations will need to be aligned manually.

41 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
4.12 Ultra 3Ph Full module commissioning 4.12.1 Parameters (UltraCella)
UltraCella ha un sottoinsieme di parametri dedicati alla configurazione
Ultra 3PH Full module has to be configured by UltraCella. del modulo Ultra 3PH Full.
1. Please make sure that, inside Ultra 3PH Full module, dip-switches of I/O
Par Description Def Min Max U.o.M.
expansion are set as per following figure (default setting):
cH1 3PH module serial address 15 1 247 -
cH2 3PH module offset serial address 0 0 232 -
cH3 Type of three phase module 0 0 1 -
0 = Evaporator
1 = Full
cA1 Sd1 probe connection 0 0 1 -
0 = in UltraCella
1 = in 3PH module
cA2 Sd2 probe connection 0 0 1 -
Address Ext Baud Prot 0 = in UltraCella
1 = in 3PH module
cA3 Sc probe connection 0 0 1 -
1 9
2 10 (Full module only)
3 11
4 12 19.2 K 0 = in UltraCella
5 13 9.6 K 1 = in 3PH module
6 14
7 15 with offset 38.4 K CAREL cEn Enable 3PH mod. 0 0 1 -
8 no offset 57.6 K Modbus
0 = disable
ON 1 = enable
OFF
Address Ext. Baud Prot
Fig. 4.s
4.12.2 Function
which corresponds to following configuration: Ultra 3PH Full Module has to be combined with UltraCella controls (P/
• Address = 15 Ns WB000S% or WB000D%). Module has inside high power actuators
• No offset to handle directly three-phase loads of the condensing and evaporator
• Baudrate = 19200bit/sec units, but logic and regulation algorithms are inside UltraCella.
• Protocol = Modbus In the table below details of where probes and loads can be connected.
2. In UltraCella, access to parameter category “3PH”
Nota:
3. Make sure that first two parameters are set as follows (Carel default • Although three-phase loads have to be physically connected to Ultra
setting): 3PH Full module, UltraCella maintains its standard configuration of
• cH1 = 15 (Address) relays.
• cH2 = 0 (Offset)
Connected
4. For 3PH Full expansion module, set Input UltraCella Ultra 3PH Full module
• cH3 = 1 Ambient probe  -
cA1 = 0
 -
5. If defrost probe and auxiliary evaporator defrost probe have to be Defrost probe Sd1
cA1 = 1
connected to Ultra 3PH Full module, set: - 
• cA1 = 1 cA2 = 0
• cA2 = 1 Defrost probe auxiliary  -
evaporator Sd2 cA2 = 1
6. If condenser probe has to be connected to Ultra 3PH Full module, set: - 
cA3 = 0
• cA3 = 1  -
Condensing probe Sc
cA3 = 1
7. Enable 3PH Full module by setting: - 
• cEn = 1
Uscita UltraCella Ultra 3PH Full module
 
Compressor command
(1PH) (3PH)
Note: to ensure the communication between UltraCella and the  
expansion module, the I/O expansion network address and parameter Defrost heaters
(1PH) (3PH)
cH1 on UltraCella must be set to the same value (default 15).  
Evaporator fans
(1PH) (3PH)
Important: this setting of the dipswitches on the I/O expansion 
Light -
(corresponding to serial address 15) is active starting from November (1PH)
2015 and guarantees “plug & play” communication with UltraCella AUX1
 
controllers running software release 1.7 (default value cH1=15). Expansion (1PH) (1PH)
modules manufactured prior to November 2015 have the default address 
AUX2 -
setting as 1 (different dipswitch configuration than shown in the figure). (1PH)
Tab. 4.g
UltraCella controllers running a software release lower than 1.7 are set
with cH1=1 by default. In some cases, then, the two configurations will
need to be aligned manually.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 42

 ENG
5. OUTPUTS CONFIGURATION AND PROTECTIONS
5.1 Analogue output 5.2.3 Output operation AUX1/AUX2
It is available analog output Y1, to drive the evaporator fans designed to The AUX1 and AUX2 outputs can be associated with different functions,
be operated with input 0 ... 10 V. See the chapter 6.9. such as alarm, auxiliary output controlled by AUX button, the pump down
valve, condenser fan, compressor, second compressor with rotation. For
Par. Description Def Min Max U.o.M. further explanations, please consult chapter 3.2.
HO1 Configuration output Y1 0 0 3 -
0 Not active Par. Description Def Min Max U.o.M.
1 Modulating output (generic H1 Configuration of output AUX1 1 0 17 -
function) 0 = Normally energized alarm
2 Variable speed evaporator fans set 1 = Normally deenergized alarm
on Sd probe 2 = Activation by AUX1 key or by Digital
3 Variable speed condenser fans Input
3 = Bowl resistance activation
4 = Auxiliary evaporator defrost
5 = Pump down valve
6 = Condenser fan
7 = Delayed compressor
5.2 Digital Outputs 8 = Control output 1 ON/OFF
9 = Control output 2 ON/OFF
10 = Do not select
5.2.1 Delay start for compressor output 11 = Do not select
12 = Do not select
Par. Description Def Min Max U.o.M. 13 = Second compressor step
c0 Compressor/ fan start delay at power on 0 0 15 min 14 = Second compressor step with
rotation
• c0: from the moment in which the control is powered-up, turning 15 = humidity output
on the compressor and the evaporator fan is delayed by a time (in 16 = reverse mode output (heat)
minutes) equal to the value assigned to this parameter. This delay 17 = auxiliary output managed by time
helps to protect the compressor against repeated starts in the case of bands
frequent power failures. H5 Configuration of output AUX2 1 0 17 -
See H1
Note: for the other protection parameters (c1, c2, c3) see
chapter 4.

5.2.2 Safety devices for outputs with different relays

Par. Description Def Min Max U.o.M.
c11 Second compressor start delay 4 0 250 s
• c11 sets the activation delay between the first and the second
compressor (or between the first and the second step of the
compressor).

c1
c3 c2

ON

Step1

OFF

ON

Step2

OFF

Power_ON
t
c0 c11

Fig. 5.a
Key
Step1 Step 1 compressor
Step2 Step 2 compressor
t Time

43 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
6. CONTROL
6.1 Switching the controller ON and OFF 6.3 Set point
The state of ON/OFF can be controlled by more than one source, keyboard, The reference output is the compressor (CMP).
digital input and supervisor. When the controller is off, the display will The controller can operate in two different modes, that can be selected
show the temperature selected for parameter /t1 alternating with the using parameter r3:
OFF message. The digital input can be used to switch the controller on/ • direct with defrost;
off, setting parameter A5/A9 to “6”. The activation state of ON / OFF from • direct without defrost;
digital input has priority over the one from the supervisor and keyboard. Par. Description Def Min Max U.o.M.
Origin Priority Notes St Set point 0 r1 r2 °C/°F
Digital input 1 Disable On/Off from keypad and supervisor rd Differential 2.0 0.1 20 °C/°F
Keyboard 2 r1 Minimum set point -50 -50 r2 °C/°F
Supervisor 3 r2 Maximum set point 60 r1 200 °C/°F
Tab. 6.a r3 Operating mode 0 0 1 -
0 Direct with defrost
1 Direct without defrost

CMP
ON
6.2 Virtual probe
The control output of the controller is the compressor output. The control
probe is the ambient probe B1 (default setting), while the probes B2, B3, OFF
B4, B5 may be associated with the functions of defrost probe 1/2, outlet
probe, intake probe, condenser probe. If the cold room is very large you rd Sv
should also use a second probe to control the temperature of the room. St
The controller will activate the compressor based on the requirements
of the virtual probe (Sv), obtained from weighed average of the 2 probes Fig. 6.b
(B1, B2). Key
St Set point
Par. Description Def Min Max U.o.M.
rd Differential
/4 Virtual probe composition 0 0 100 - Sv Virtual probe
0 = probe B1 CMP Compressor
100 = probe B2
If you have activated the second compressor output (H1, H5 = 13, 14) on
The /4 parameter is used to determine the virtual probe (Sv) as a weighted AUX output, the activation of the compressor is at St + rd/2 and that of
average of the control sensor probe B1 and B2, according to the formula: the auxiliary compressor AUX in St + rd, according to the figure below.

[(B1*(100-/4)+B2*/4] AUX
Sv= ON
100
OFF
CMP
ON

OFF

rd/2 rd
rd/2 Sv
St
Fig. 6.c
UltraCella
Key
St Set point
rd Differential
Sv Virtual probe
CMP Compressor
AUX Auxiliary output
Fig. 6.a
The control set point, in normally operating conditions, is indicated by
Key parameter St.
B1 Outlet probe This value may however change based on other algorithms:
B2 Intake probe • Set point variation from digital input (St+r4)
• Set point variation by time band (St+r4)
• Set point variation by ramp (variable set point)
with the following priority:

Priority Function Control set

point value
1 Set point variation from digital input St+r4
(A5/A9=7)
2 Set point variation by time band St+r4
3 Set point variation (ramps) Variable
according to
parameters PS1,
PS2, PS3 and PH1,
PH2, PH3
4 Set point by parameter St St

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 44

 ENG
6.3.1 Set point variation from digital input 08:30 to 18:30, and 9°C at all other times, set:
With UltraCella, the control set point can be changed using digital inputs • St = 4;
DI2 and DI3. This function may be useful in applications where the control • r4 = 5;
set point can be increased when the store is not open to the public (for • dSn = 9;
example, at night), thus guaranteeing energy savings and the certainty • hSn = 8;
that the product is ready for display and sale when needed. • MSn = 30;
Digital input DI2 is associated with parameter A5, while digital input DI3 • hSF = 18;
is associated with parameter A9. To enable set point variation from digital • MSF = 30;
input, set A5=7 (for DI2) or A9=7 (for DI3). • H9 = 1 -> se H9=0 the time band will never be active

Par. Description Def Min Max U.o.M. Note: when set point variation is enabled, the SET button flashes
A5 Configuration of digital input 2 (DI2) 0 0 15 - to indicate that the control set point is not the value set for
7 = set point variation parameter St.
A9 Configuration of digital input 3 (DI3) 0 0 15 -
7 = set point variation Note: if the second row of the display shows the set point (/t2 =
6, on models where featured), the value displayed will be the
When the digital input is active (closed), the control set point will be the effective control set point (therefore, either St or St + r4, depending on
sum of the values of parameters St and r4; when the digital input is not whether or not the time band is active).
active (open), the control set point will be the value set for parameter St
(normal operation).
6.3.3 Set point ramps
• DI2 / DI3 not active (open) -> control set point = St
• DI2 / DI3 active (close) -> control set point = St + r4
Very large cold rooms used to preserve food at below-zero temperatures
Par. Description Def Min Max U.o.M. (freezers) may, for logistics or constructional reasons, require concrete
r4 Offset set point 3,0 -20,0 20,0 °C/°F floors. Initially, the cold room, and thus its floor, which are initially at
ambient temperature, if cooled to the set point in the shortest possible
time (pull down), cracks may form in the floor, causing significant damage.
Note: when set point variation is enabled, the SET button flashes For this reason, in these types of cold rooms ramps of variable duration
to indicate that the control set point is no longer the value set for and intensity are used to bring the cold room to the set point over a time
parameter St. that is suitable for the concrete floor.
On UltraCella, ramps can be configured that are divided into three phases.
Note: if the second row of the display shows the set point (/t2 = The slope of the ramp depends on the final temperature set point and
6, on models where featured), the value displayed will be the the duration of each phase.
effective control set point (therefore, either St or St + r4, depending on Phase 1: typically this is an initial cooling ramp, from ambient temperature
the status of the digital input) to a final temperature around 0°C, lasting several days (default 6 days).
Phase 2: typically this is a phase in which the temperature reached in
phase 1 is maintained, lasting several days (default 2 days)
Phase 3: this is the second and final cooling ramp to the final temperature
6.3.2 Set point variation by time band set point for storing the frozen food and, being the most critical phase,
With UltraCella, the control set point can also be changed based on time typically lasts longer (default 10 days).
bands, using the RTC fitted on the device. The function is similar to the
one described in the previous paragraph, however this is more useful Par. Description Def Min Max U.o.M.
when needing to change the set point repeatedly at fixed times. PS1 Ramps: final set point, phase 1 0 -50,0 200,0 °C/°F
When the time band is active, the control set point will be the sum of the PS2 Ramps: final set point, phase 2 0 -50,0 200,0 °C/°F
values of parameters St and r4. PS3 Ramps: final set point, phase 3 -30,0 -50,0 200,0 °C/°F
PH1 Ramps: duration of phase 1 6 0 10 days
PH2 Ramps: duration of phase 2 2 0 10 days
• Time band not active -> control set point = St PH3 Ramps: duration of phase 3 10 0 10 days
• Time band active -> control set point = St + r4
Example: ramp starting from an ambient temperature of 30°C, the first
Par. Description Def Min Max U.o.M.
phase reaches 0°C in 6 days (phase 1), maintained at 0°C for 2 days (phase
r4 Offset set point 3,0 -20,0 20,0 °C/°F
2) and final cooling ramp to the set point of -30°C over 10 days (phase 3).
To activate set point variation by time band, a time band needs to be
REFRIGERATION CURVE FOR COLD ROOMS
enabled by setting the following parameters:
30 °C

Par. Description Def Min Max U.o.M. 20 °C

dSn Set point variation by time band: day 0 0 11 days 2,5 K /12 h
internal temperature

0 = disable 10 °C
48 hours
1, 2, …7 = Sunday, Monday, … Saturday at 0°C

8 = Monday to Friday 0 °C

9 = Monday to Saturday 1,5 K /12 h

10 = Saturday & Sunday -10 °C

11 = every day
hSn Start set point variation by time band: 0 0 23 hours -20 °C

hours
-30 °C
MSn Start set point variation by time band: 0 0 59 min h h h h h h h h h h 0h 0h 0h 0h 0h 0h 0h 0h 0h
00 00 00 00 00 00 00 00 00 00 d0 d0 d0 d0 d0 d0 d0 d0 d0
minutes 0d 1d 2d 3d 4d 5d 6d 7d 8d 9d 10 11 12 13 14 15 16 17 18
time after starts of ramps
hSF End set point variation by time band: 0 0 23 hours
hours
MSF End set point variation by time band: 0 0 59 min Note: when the ramps are active, and throughout their duration,
minutes the control set point is no longer the value indicated by parameter
H9 Enable set point variation by time band 0 0 1 - St, but is automatically recalculated, depending on the values set for
0/1=disabled/enabled parameters PSi and PHi, every 12 hours.

Example: to have a control set point of 4°C from Monday to Saturday, Note: in the event of a blackout when a ramp is in progress, when
power returns, the ramp resumes from where it was interrupted if
45 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
the temperature in the cold room during the blackout has not increased The pump down has the aim to completely empty the evaporator of the
by a value greater than parameter Pdt from the set point reached just refrigerant at each stop of the compressor. After this phase, you can safely
before the blackout turn off the compressor, so that the liquid is not present the next time the
• if (set point before blackout – current cold room temperature) ≤ compressor is started. When the set point is reached, the control closes
Pdt -> brief blackout -> resume ramp from the phase where it was the pump down valve to stop the flow of refrigerant to the evaporator,
interrupted, with a new starting set point equal to the temperature and, after a certain time, the compressor. In the application diagram
reached by the cold room, and the phase lasts the remaining duration there are the pump down valve and the low pressure switch. When the
(as if the blackout had not occurred); control requires turning on the compressor, if the safety periods c1 and
• if (set point before blackout – current cold room temperature) > Pdt c2 have passed, the pump down valve is opened and after the time set in
-> extended black-out, the temperature has increased too much -> parameter c8 the compressor is activated.
restart the ramp from the beginning (phase 1, PS1, PH1).
This aims to avoid damage to the floor due to an excessively fast pull Par. Description Def Min Max U.o.M.
down. c7 Maximum pump down time (PD) 0 0 900 s
0 = Pump down disabled.
Par. Description Def Min Max U.o.M. c8 Compressor start delay after opening of 5 0 60 s
Pdt Ramps: maximum set point variation 20,0 10,0 30,0 °C/°F pump down valve PD
after blackout H1 Configuration of output AUX1 1 0 17 -
…5 = pump down valve
H5 Configuration of output AUX2 1 0 17 -
…5 = pump down valve
Note: At the end of the third phase, the control set point returns
to the value set for parameter St -> to avoid abrupt variations, it is
recommended to set PS3 = St. C
CMP
Enable ramps
L
The ramps need to be enabled by setting parameter Pon=1

Par. Description Def Min Max U.o.M.

F P
Pon Enable set point ramps 0 0 1 -
1 = ramps enabled
S
1. Set Pon=1;
2. The evaporator fans are activated for 3 minutes (fan relay ON and
analogue output at the maximum value corresponding to parameter T V2 M E
F6, if enabled); PDV
3. Initial ramp set point = Sv (virtual control probe, which coincides with the
current cold room temperature);
4. The controller adjusts the control set point based on parameters PS1, PS2, Fig. 6.d
PS3 and PH1, PH2, PH3. During each phase, the control set point is
Key
recalculated every 12 hours;
5. At the end of the phase (duration PH3), the ramps are automatically CMP Compressor
disabled (Pon=0) and the control set point is once again the value C Condenser
L Liquid receiver
of St.
P Low pressure switch
F Dehydrator filter
Note: when the ramps are enabled, and throughout their E Evaporator
duration, the SET button flashes to indicate that the control set S Liquid indicator
point is no longer the value set for parameter St. V2 Thermostatic expansion valves
PDV Pump down valve
Note: if the second row of the display shows the set point (/t2 =
6, on models where featured), the value displayed will be the
effective control set point. Note: time c8 is ignored when pump down is disabled (c7=0). In
this case, the pump down valve (H1=5 or H5=5) can be used to
Note: to restart the ramps, reset Pon=1 control a solenoid valve, whose operation always matches the compressor
output. c8 is also ignored when pump down is enabled (c7>0) and the
Note: the ramps are always disabled if set point variation from compressor OFF time is 0 (c2= 0).
digital input / time band is active
You can select the pump down:
Note: the ramps can be activated even when UltraCella is OFF • on pressure (pressure switch mandatory): once the pump down
valve closes, the compressor continues to operate until reaching the
Note: to skip a specific phase of the ramp, set PHi=0 (i=1, 2 or 3) low pressure value (contact opened). At this point the compressor is
turned off. If the pressure switch does not change within the time c7,
alarm “Pd” triggers, pump down ended due to time-out. The Pd alarm
is reset automatically if in the next pump down low pressure is reached
within the time c7.
• on time (pressure switch optional): after the valve closes, the
compressor operates for the time c7. The ‘Pd’ alarm, Pump down ended
by time-out, is deactivated.

c10 = 0: Pressure pump down

Pressure switch changes within c7 Pressure switch changes after c7

6.4 Pump down

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 46
 ENG
ON ON ON
CMP, FAN
CMP, FAN CMP, FAN
OFF OFF OFF
ON ON ON
PDV PDV VPD
OFF OFF OFF
ON ON ON
Pressure
Pressure Pressure
switch switch switch
OFF OFF OFF
ON ON ON
Alarm Pd
Alarm Pd AtS
OFF OFF
OFF
Sv Sv
Sv
St St
St

c7 c7 c7 c7
t
Fig. 6.e Fig. 6.f Fig. 6.g
Key Note: low pressure = pressure off/open.
CMP, FAN Compressor, fan
PDV pump down valve Key
Pressure switch Pressure switch CMP, FAN Compressor, fan t Time
Sv Virtual probe VPD Pump down valve AtS Autostart in pump down
c7 Pump down maximum time St Set point Pressure switch Pressure switch
Pd Pump down alarm Sv Control probe
t Time
St Set point
Note: Notes:

• if during the pump down there is a new demand for cooling, the pump • at compressor autostart, the safety times c1 and c2, not c3 are
down procedure terminates, and the pump down valve is opened (the respected;
compressor is already on from the previous pump down phase); • the message “AtS” is reset automatically on the next correct pump
• in case of “Pd” alarm the auto-start function is disabled. down cycle.

6.6 Continuous cycle

6.5 Autostart in pump down To activate the continuous cycle by keyboard see Chapter 3 (parameter
As seen in the previous paragraph, once you reach the set point, the value cc> 0). During operation in a continuous cycle, the compressor
control closes the pump down valve and then the pressure switch continues to operate regardless the control, for the time “cc”, to lower the
changes and signals low pressure. If, due to problems of sealing of temperature even below the set point. The continuous cycle is stopped
the valve, the pressure switch changes again, you can reactivate the after the time cc or when reaching the minimum specified temperature,
compressor with the Auto start function, signalled by the message “Ats”. corresponding to the minimum temperature alarm threshold (AL). If,
This message is erased on the next correct pump down cycle after the end of the continuous cycle, the temperature falls below the
minimum temperature threshold, the low temperature alarm signal can
Par. Description Def Min Max U.o.M. be ignored by suitably setting the c6 parameter: the alarm bypass delay
c9 Autostart in pump down 0 0 1 - time after continuous cycle.
0 whenever pump down valve
closes Par. Description Def Min Max U.o.M.
1 whenever pump down valve cc Continuous cycle duration 0 0 15 hour
closes & every request of c6 Low temperature alarm delay after 2 0 250 hour
low pressure switch without continuous cycle
regulation request A5 Digital input configuration 2 (DI2) 0 0 15 -
…
14 = Continuous cycle activation
A9 Digital input configuration 3 (DI3) 0 0 15 -
…
14 = Continuous cycle activation

6.7 Door switch control

See chap. 4

47 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
6.8 Defrost Sd
Introduction dt1
These parameters (dd1…dd8) can be used to set up to 8 defrost events dt1-1
linked to the system clock (RTC)
Par. Description Def Min Max U.o.M.
dd1…8 Defrost 1…8: day 0 0 11 -
0 Disabled t
1…7 Monday…Sunday ON d0=0, 1
8 From Monday to Friday DEF
9 From Monday to Saturday OFF
10 Saturday and Sunday
11 Daily t
hh1…8 Defrost 1…8: hour 0 0 23 hour ON d0=2, 3
nn1…8 Defrost 1…8: minute 0 0 59 min. DEF
UltraCella allows you to manage the following types of defrost, depending OFF

on parameter d0:
0. electric heater defrost by temperature (placed near the evaporator); dP1
t
1. hot gas defrost by temperature.
2. electric heater defrost by time; Fig. 6.h
3. hot gas defrost by time. Key
Note: Ed1 and Ed2 indicate that the defrost ended due to time- t Time
out. dt1 End of defrost temperature
dP1 Maximum defrost duration
Sd Defrost Probe
Note: Ed1 and Ed2 alarms can be disabled by A8 parameter. d0 Type of defrost
DEF Defrost
Par. Description Def Min Max U.o.M.
A8 Ed1, Ed2 enable 0 0 1 -
0/1= disabled/enabled
1. electric heater defrost (d0 = 0, 2): operating cycle.
The operating cycle refers to default values of the parameters F2 and F3.
The end of the defrost cycle can be by temperature, and in this case it is
necessary to install the defrost probe Sd (to select between B2 and B3) or
by time. In the first case the defrost ends if the probe Sd measures a value C
greater than the value of dt1 or dP1 time has elapsed, in the second case
if the defrosting phase exceeds the maximum time dP1. At the end of CMP
the defrost the controller can enter in dripping status (present if dd> 0),
in which the compressor and the fans are turned off, and subsequently in L
the state of post-dripping (if present Fd> 0), in which the control resumes
with fans off. You can choose the display on the user terminal during
defrost, using parameter d6. F
Par. Description Def Min Max U.o.M.
d0 Type of defrost 0 0 3 -
S
0 Heater by temperature
1 Hot gas by temperature PDV
2 Heater by time
3 Hot gas by time
T V2 M B3
dt1 End defrost temperature, main 4 -50 200 °C/°F E
evaporator
dt2 End defrost temperature, auxiliary 4 -50 200 °C/°F
evaporator
dP1 Maximum defrost duration 30 1 250 min Fig. 6.i
dP2 Maximum defrost duration, auxiliary 30 1 250 min
evaporator POST
d6 Terminal display during defrost 1 0 2 - REFRIG PUMP DEF DRIP DRIP REFRIG
0 = Temperature alternated with dEF DOWN (REF) (dd) (Fd)
1 = Last temperature shown before ON
c8
defrost CMP
2 = dEF OFF
ON
PDV
OFF
ON
FAN
OFF
F0=0 F3=1
ON
RES
OFF

t
Fig. 6.j
Key
UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 48
 ENG
Key
CMP Compressor
Refrig Refrigeration CMP Compressor
PDV Pump down valve Refrig Refrigeration
Pump down Pump down phase FAN Evaporator fan
FAN Evaporator fan Def Defrost
Def Defrost V_def Hot gas valve
RES Resistance (defrost heater) Drip Drip
Drip Drip E Evaporator
E Evaporator Post drip Post drip
Post drip Post drip C Condenser
C Condenser B3 Defrost probe
V2 Thermostatic expansion valve V2 Thermostatic expansion valve
F Dehydrator filter L Liquid receiver
t Time F Dehydrator filter
B3 Defrost probe S Liquid indicator
L Liquid receiver t Time
S Liquid indicator
The defrost is activated, upon priority:
Note: • from keyboard, using the defrost key;
• in pump-down the fan activation is determined by F0; • from clock, setting the event and the starting mode, with maximum 8
• in defrost the fan activation is determined by F3. defrosts a day (parameters dd1...dd8);
• setting the cyclic range “dI”;
• from digital input;
• from supervisor.
2. hot gas defrost (d0 = 1, 3): operating cycle.
The operating cycle refers to default values of the parameters F2 and F3. The defrost is disabled:
• defrost by temperature: when the defrost probe detects a temperature
greater than the defrost end temperature dt1;
C V_def • defrost by time: in the absence of the defrost probe, the defrost ends
after the maximum time set by parameter dP1.
CMP
M
L
6.8.1 Maximum period of time between consecutive
defrosts
F
Par. Description Def Min Max U.o.M.
dI Maximum interval between 8 0 250 hour
S consecutive defrosts
0 = defrost not performed

T V2 B3 E The parameter dI is a security parameter that allows cyclical defrosts

every “dI” hours even in the absence of the Real Time Clock (RTC). At the
beginning of each defrost cycle, regardless of duration, a count is started.
If the dl time is exceeded without performing any defrost, the defrost is
automatically activated. The counter remains active even if the controller
is off.
Fig. 6.k
Note: the defrost output (DEF) is used for command of the hot Example: in case of failure for example at RTC the scheduled defrost by
gas valve V_def. td3 (= dd3, hh3, nn3) is not made, after the safety time dI starts a new
defrost.
REFRIG DEF DRIP POST REFRIG
dl
(hot gas) DRIP
ON ON
c8 DEF
CMP
OFF
OFF
dd1 t
ON
dd2
FAN dd3

OFF
F0=0 F3=1
Fig. 6.m
ON Key
V_def dI Maximum interval of time between consecutive defrosts
dd1…dd3 Scheduled defrosts
OFF
DEF Defrost
t Time
t
Note:
Fig. 6.l
• if the interval dI expires when the controller is OFF, when it is started
again a defrost is performed;
• to ensure regular defrosts, the interval between defrosts must be
greater than the maximum defrost duration, plus the dripping time
and post-dripping time;
• if setting dl=0 the defrost is performed only if activated from keyboard
or by setting the scheduled defrosts (ddi).
49 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
6.8.2 Other defrost parameters
Par. Description Def Min Max U.o.M.
d3 Defrost activation delay 0 0 250 min
ON
d4 Defrost at start-up
0/1=No/Yes
0 0 1 -
CMP
d5 Defrost delay at start-up 0 0 250 min
d8 High temperature alarm delay after 1 0 250 hour OFF
defrost (and door open)
dpr Defrost priority over continuos cycle 0 0 1 - ON F0=0
0/1=No/Yes
Evap. fan
• d3 determines the time that must elapse, when the defrost is activated,
between the stopping of the compressor (electric heater defrost) or PWM mod.
the starting of the compressor (hot gas defrost), and the activation of
the defrost relays on the main and auxiliary evaporators. In the hot gas Sd
defrost, the delay d3 is useful for ensuring a sufficient amount of hot Sv-F1
gas before activation of the hot gas valve; (Sv-F1)-Frd
• d4 determines whether to activate or not the defrost at the controller
start-up. The defrost at start-up request has priority over the activation ON
of the compressor and the continuous cycle. Force a defrost at
controller start-up may be useful in special situations. F0=1
Evap. fan
Example: frequent power drops inside the plant. In case of lack of voltage
the tool resets the inner clock that calculates the period of time between PWM mod.
two defrosts, starting from zero. If, in an extreme case, the frequency of
Fig. 6.n
the power failure were greater than the defrost frequency (e.g. a power t
Key
failure every 8 hours, against a defrost every 10 hours) the controller
would never perform a defrost. In a situation of this type, it is preferable CMP Compressor
to activate defrost on start-up, above all if the defrost is controlled by PWM mod. PWM modulation
F1 Fan activation threshold
temperature (probe on the evaporator), therefore avoiding unnecessary
Frd Fan activation differential
defrosts or at least reducing the running times. In the case of systems Evap.fan Evaporator fan
with a large number of units, if selecting defrosts at start-up, after a power t Time
failure all the units will start defrosting, thus causing a voltage overload. Sv Virtual probe
This can cause power overload. To overcome this, the parameter d5 can Sd Defrost probe
be used. It adds a delay before the defrost, and this delay must obviously
be different for each unit. The fan can be stopped:
• d5 represents the time that elapses between the start of the controller • when the compressor is off (parameter F2);
and the start of the defrost at start-up; • during defrost (parameter F3).
• dd is used to force the stop of the compressor and the evaporator fan
after a defrost cycle in order to facilitate the evaporator dripping;
• d8 indicates the time of exclusion of the high temperature alarm 6.9.2 Variable speed fans
signalling from the end of a defrost; The installation of variable speed fans may be useful to optimise energy
• if dpr = 0, the defrost and the cycle have the same priority; if dpr = 1, consumption. In this case, the fans are powered by the mains, while the
if the continuous cycle is in progress and a defrost request intervenes, control signal is provided by UltraCella by analogue output Y1 0…10 Vdc.
the continuous cycle ends and the defrost starts.
The maximum and minimum fan speed can be set using F6 and F7
parameters (in percentage respect range 0…10V). If using the fan speed
controller, F5 represents the temperature below which the fans are
activated, with a fix hysteresis of 1°C.
6.9 Evaporator Fans Par. Description Def Min Max U.o.M.
F5 Evaporator fans cut-off temperature 15 -50 200 °C/°F
(hysteresis 1°C)
6.9.1 Fixed speed fans F6 Maximum fans speed 100 F7 100 %
The status of the fans depends on the compressor status. F7 Minimum fans speed 0 0 F6 %
When the compressor is:
• on: the fan can also be on (F0=0) or activated based on the evaporator
temperature, virtual probe Sv, based on the formula: To enable the algorithm, it’s necessary to select variable speed fans mode
(F0=2) and set analogue output 0…10 Vdc (HO1=2).
if Sd ≤ (Sv - F1) -Frd --> FAN = ON
if Sd ≥ (Sv - F1) --> FAN = OFF Par.Description Def Min Max U.o.M.
F0 Evaporator fans management 0 0 2 -
• off: the fan is controlled by a PWM that has duty cycle with a fixed …
period of 60 minutes. 2 = variable speed fans
HO1 Output Y1 0…10 V configuration 0 0 3 -
duty_cycle = F2 …
60 2 = variable speed fans regulated on Sd

Par. Description Def Min Max U.o.M.

F0 Evaporator fan management 0 0 2 -
0 = always on with compressor on
1= activation depends on Sd, Sv
F1 Fan activation temperature 5 -50 200 °C/°F
F2 Fan activation time with CMP off 30 0 60 min
HO1 Output Y1 configuration 0 0 3 -
0 = not active

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 50

 ENG
Note: Cyclic time at maximum speed (determined by both F8 and
Sd
F5+1 F0 = 2 F10) is not allowed when door is open.

F5
F1
6.9.3 Evaporator fans during defrost
F1-Frd
t There is the possibility to force the start of the evaporator fans during
control (parameter F2) and during defrost (parameter F3). During
F6 the dripping periods (parameter dd > 0) and post-dripping periods
FAN (parameter Fd > 0) the evaporator fans are always off. This is useful to
F7 allow the evaporator to return to normal temperature after defrosting,
0% t thus avoiding forcing hot air on evaporator. dd is used to force the stop
of the compressor and the evaporator fan after a defrost cycle in order to
Fig. 6.o facilitate evaporator dripping.
Par. Description Def Min Max U.o.M.
Evaporator Fan (analog output) F0= 2 F2 Fan activation time with CMP off 30 0 60 min
F3 Evaporator fans during defrost 1 0 1 -
0/1=on/off
Key Fd Post dripping time (fans off ) 1 0 30 min
F4 Humidity output during defrost 1 0 1 -
Sd Evaporator probe 0/1 = ON/OFF
F0 Evaporator fans management dd Dripping time after defrost (fans off ) 2 0 30 min
F1 Fan start temperature
Frd Fan activation differential
Note:

• if two evaporator probes are configured (Sd1 and Sd2), speed fans is
calculated in relation to probe which is measuring higher temperature 6.10 Condenser fans
(to limit hot air flow): With UltraCella, the condenser fans can be managed by one of the
if Sd1>Sd2 –› regulation on Sd1; auxiliary relays AUX1/AUX2 (in ON/OFF mode), or by analogue output
if Sd1<Sd2 –› regulation on Sd2. Y1 (0 to 10 V).
In case of defrost probe failure, speed fans is fixed to maximum value
defined by parameter F6. 6.10.1 Fixed speed fans
• If F0=2 and HO1=2, speed fan is calculated in according to Figure 6.o. The condenser fans are activated based on parameters FC4 and A0, after
Anyway, if speed fan is higher than 0, “FAN” relay DO3 is ON anyhow configuring the digital output AUX.
(closed):
if speed fan (Y1) > 0V –› “FAN” relay ON (DO3 closed) Par. Description Def Min Max U.o.M.
if speed fan (Y1) = 0V –› “FAN” relay OFF (DO3 open) FC4 Condenser fan deactivation 40 -50 200 °C/°F
temperature
A0 Alarm and fan differential 2.0 0.1 20 °C/°F
• If F0=0,1 (fixed speed fans by “FAN” relay DO3), analogue output is set
to 0 (Y1=0V)
• Inside modulation interval (F1-Frd < Sd < F1), speed fan is modulated Par. Description Def Min Max U.o.M.
in proportional way (e.g. Sd=F1-Frd/2 –› Y1 correspond to (F6+F7)/2 H1 AUX1 output configuration 0 0 17 -
percentage) …
6= condenser fans
H5 AUX2 output configuration 0 0 17 -
Because of mechanical inertia of motor, some EC fans cannot start with …
a low speed set by parameter F7. To overcome this, fans can be started 6 = condenser fans
with maximum speed set by parameter F7 for a “peak time” defined by
parameter F8, irrespectively of Sd temperature.
On the other hand, if fans operates for too long time at a reduced speed, Sc
ice can form on the blades. To avoid this, at interval of F10 minutes, fans FC4+A0
are forced to maximum speed for “peak time” defined by F8
FC4

Par. Description Def Min Max U.o.M.

F8 Fans peak time 0 0 240 s
0 = function disabled t
F10 Evaporator fans forcing time at 0 0 240 min
maximum speed ON
0 = function disabled FAN
OFF

t
Fig. 6.p
speed fans defined by Sd
Key
F6 Sc Condenser probe
FAN Condenser fans
FC4 Turn off temperature
F7 t Time
A0 Differential

F8 F8 F8 Note: if an alarm triggers at condenser probe, the output

t
condenser fan is always on.
F10 F10

51 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
6.10.2 Variable speed fans Par. Description Def Min Max U.O.M.
It may be useful to manage the fans at variable speed, in order to optimise FCn Variable speed condenser fans: min. 0 0 FCH %
energy consumption. In this case, the fan is powered by the mains, while capacity percentage
the 0 to 10 Vdc control signal is supplied by UltraCella via output Y1.
To activate this mode, the condensing temperature needs to be Example 2: extended output range, 0 to 10 V (FCL=0, FCH=100), minimum
determined. This can be done in two ways: modulation capacity 60%.
:
• Using an NTC / PT1000 temperature probe connected to input B3 as a Analog
condensing temperature probe (Sc): output
/A3 = 2 (Sc) FCH Max capacity= 100%
• Connecting a pressure probe (4 to 20 mA / 0 to 5 Vrat) to input B5 as a output max
value = 10V
condensing pressure probe (Scp):
/P5 = 0 (4…20mA) / 1 (0…5Vrat)
/A5 = 3 (Scp) -> the pressure value will be converted to a temperature
(Sc) based on the type of refrigerant, defined by setting the parameter FCL FCn
input max min capacity= 60%
PH: value= 0V
Set capacity Sc
Par. Description Def Min Max U.O.M. differential differential (condensing
PH 1= R22 10 = R717 19 = R407A 3 1 25 - temperature)
FCd FCd
2 = R134A 11 = R744 20 = R427A FCS
(setpoint)
3 = R404A 12 = R728 21 = R245FA
4 = R407C 13 = R1270 22 = R407F Fig. 6.r
5 = R410A 14 = R417A 23 = R32 In this example, the range of modulation of the 0 to 10 V output is:
6 = R507A 15 = R422D 24 = HTR01 FCS+0.2*FCd < Sc < FCS+FCd
7 = R290 16 = R413A 25 = HTR02
Example 3: limited output range, 2 to 10 V (FCL=20, FCH=100), minimum
8 = R600 17 = R422A modulation capacity 60%
9 = R600A 18 = R423A
To activate analogue output Y1 for condenser fan control, set parameter Analog
HO1. output
FCH max capacity = 100%
Par. Description Def Min Max U.O.M. output max
value = 10V
HO1 Output Y1 configuration 0 0 3 -
3 = variable speed condenser fans
FCn
- min capacity = 60%
The maximum and minimum fan speed can be set using parameters FCH FCL
and FCL (as a percentage of the range from 0 to 10 V). output min
value= 2V
Set capacity Sc
Par. Description Def Min Max U.O.M. differential differential (condensing
FCH Variable speed condenser fans: max. 100 FCL 100 % temperature)
FCd FCd
output value FCS
FCL Variable speed condenser fans: min. 0 0 FCH % (setpoint)
output value
Fig. 6.s
The 0 to 10 V output is activated in direct proportional mode, centred In this example, the range of modulation is still
around the condenser fan control set point FCS and differential FCd. FCS+0,2*FCd < Sc < FCS+FCd
for starting the fans, and
Par. Description Def Min Max U.O.M. FCS-FCd < Sc < FCS+FCd
FCS Variable speed condenser fans: set point 15,0 -100.0 200,0 °C/°F for stopping (the fans stop when the condensing temperature is less than
FCd Variable speed condenser fans: 2,0 0,1 10,0 °C/°F FCS-FCd.
differential
Note: if a condensing temperature/pressure probe error occurs
(E2 for Sc or E4 for Scp), the analogue output will take the
Example 1: extended output range, 0 to 10 V (FCL=0, FCH=100). maximum value indicated by parameter FCH, except in the following
events:
Analog • CHt (high condenser temperature alarm, if configured)
output • EPM (motor protector alarm, 3PH module, if present and configured)
FCH Max capacity= 100% • EPU (high/low pressure or Kriwan alarm, 3PH module, if present and
max output configured)
value= 10V

FCn
min capacity = 0%
6.10.3 Floating condensing temperature set point
FCL
min output The control set point for variable speed condenser fans (parameter FCS)
value= 0V
may be either fixed or variable (floating condensing temperature). The
Sc
differential differential (condenser type of set point is selected using parameter FCt.
temperature)
FCd FCd
FCS Par. Description Def Min Max U.o.M.
(setpoint) FCt Variable speed condenser fans: fixed or 0 0 1 -
variable set point
Fig. 6.q 0/1=fixed FCS/floating
In this example, the minimum modulation capacity FCn is 0, therefore the
range of modulation of the 0 to 10 V output is: FCS-FCd < Sc < FCS+FCd. The purpose of the floating condensing temperature function is to
. lower the condensing temperature based on the outside temperature,
so as to preserve correct compressor operation. The floating condensing
temperature set point algorithm requires an outside temperature probe
UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 52
 ENG
(SA), usually located near to the condenser, so as calculate the reference 6.12 Bowl resistance
control value, as shown in the following figure:
The resistor is used to heat the collection tank after the defrosting phase,
to prevent the ice from blocking the passage of water.
floating set point The resistance is activated for 3 minutes before the programmed defrost
FSH (max) or simultaneously with a manual defrost. The resistance is always off after
the defrost phase.
Par. Description Def Min Max U.o.M.
FSO H1 Configuration of output AUX1 1 0 17 -
(offset) …
3 = bowl resistance activation
FSL (min) H5 Configuration of output AUX2 1 0 17 -
SA …
3 =bowl resistance activation
t
external temperature
Fig. 6.t 6.13 Defrosting with 2 evaporators
To activate the floating condensing temperature function, as well as You can configure up to 2 defrost probes and up to 2 evaporator outputs.
setting FCt=1, B3 (parameter /A3) or B4 (parameter /A4) needs to be The control recognizes the configuration based on the following table
configured as an outside temperature probe (SA). (probe 1 is the control probe and cannot be configured)
Par. Description Def Min Max U.o.M.
DEFROST PROBES AND EVAPORATORS OUTPUT CONFIGURATION
/A3 Probe 3 configuration 0 0 5 -
… Case Defrost Evaporator Notes
4 = out. temp. probe (SA) probes outputs
/A4 Probe 4 configuration 0 0 4 - 1 B2 Evap. 1 B2 acts on the evap. 1
… 2 B2 Evap. 1 and 2 B2 acts on the evap. 1
1 = out. temp. probe (SA) 3 B2 and B3 Evap. 1 B2 and B3 act on evap. 1 (start
and end of defrost based on the
Note: if the outside temperature probe SA is not configured, or if minimum value probe)
the probe has an error (E2 for B3, E3 for B4), the floating condensing 4 B2 and B3 Evap. 1 and 2 B2 acts on the evap. 1 and B3 act
on evap. 2
temperature algorithm will be disabled, and the control set point will be
Tab. 6.b
fixed (FCS).
The algorithm allows for the floating condensing temperature set point
to vary between a minimum (parameter FSL) and a maximum (parameter
FSH) and, based on the outside temperature (SA), an offset is added
(parameter FSO). For details on these parameters, see the datasheet for
CASE 4: 2 PROBES AND 2 EVAPORATORS
the condenser used
.
C
Par. Description Def Min Max U.o.M.
FSL Floating condensing temp. set point: 5,0 -100,0 FSH °C/°F
min value
FSH Floating condensing temp. set point: 25,0 FSL 200,0 °C/°F L CMP
max value
FSO Floating condensing temp. set point: 5,0 -50,0 50,0 °C/°F
offset F

B2
6.11 Duty setting T V1
In the event the alarm “rE” (virtual control probe fault), the parameter c4 is E1
used to ensure the operation of the compressor until the fault is resolved.
The compressor cannot be activated according to the temperature (due
to the faulty probe), it is activated cyclically with a time of operation (ON)
equal to the value assigned to c4 and a switch-off time (OFF) fixed at 15 B3
minutes . T V2
E2
ON
CMP Fig. 6.v
OFF Key
E1/2 Evaporator 1/2
t
c4 15 C Condenser
V1/2 Thermostatic expansion valve 1/2
Fig. 6.u L Liquid Receiver
B2/B3 defrost probe 2, 3
Par. Description Def Min Max U.o.M. CMP Compressor
c4 Compressor running time in duty 0 0 100 min F Filter drier
setting S Liquid indicator

53 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
6.14 Second compressor with rotation Example 2
Second compressor output with double step control with rotation: the ON
compressors will be turned on as follows: REQ1
• alternately for single step requests (as in example 3) OFF
• the first to be turned on will be the first to be turned off for the 2 steps
requests (as in examples 1, 2 and 4) t
ON
Par. Description Def Min Max U.o.M.
REQ2
H1/H5 Configuration of output AUX1/AUX2 1 0 17 -
OFF
14 = second compressor with rotation
management t
ON
Sv
CP1
St+rd OFF
St+rd/2
St t
ON
t
CP2
ON
OFF
CP1
OFF
t
t
Fig. 6.z
ON
CP2
OFF
Example 3
t
ON
Fig. 6.w REQ1
OFF
ON
CP2 D t
ON
OFF
ON REQ2
D OFF
CP1
OFF t
ON
Sv CP1
rd/2 rd/2
OFF
St
Fig. 6.x t
Key ON
SV Virtual probe CP2
CP1 Compressor 1 OFF
CP2 Compressor 2
rd Differential t
t time Fig. 6.aa
St Set point
Example 4
Operation examples: (NOTE: REQ1: Sv > St + rd/2; REQ2: Sv > St + rd) ON
REQ1
OFF
Example 1
ON t
REQ1
ON
OFF
REQ2
OFF
t
ON t
REQ2
ON
OFF
CP1
OFF
t
ON t
CP1
ON
OFF
CP2
OFF
t
ON t
CP2
OFF
Fig. 6.ab
Key
t REQ1 request 1
Fig. 6.y REQ2 request 2
t time
CP1 compressor 1
CP2 compressor 2

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 54

 ENG
6.15 Control with dead band 6.16 AUX output activation by time band
As well as the control output in direct mode (cooling, compressor), on With UltraCella, auxiliary outputs AUX1/AUX2 can also be activated by
UltraCella one of the two auxiliary outputs (AUX1/AUX2) can be selected time band, , using the RTC fitted on the device.
in reverse mode (heating, by electric heater / other actuators). This type of When the time band is active, the AUX output (H1 for AUX1, H5 for AUX2)
control features an area in which the selected output is not active, called configured will be active (ON, relay closed).
the dead band (parameter rn). Parameter rr represents the differential for • Time band not active -> AUX output not active (OFF, relay open)
the output in reverse mode. • Time band active -> AUX output active (ON, relay closed)
Par. Description Def Min Max U.o.M. Par. Description Def Min Max U.o.M.
rn Dead band 0 0 60 °C/°F H1 AUX1 output configuration 1 0 17 -
rr Differential for control with dead band 2,0 0,1 20 °C/°F …
17 = output managed by time band
To activate heating/cooling control with dead band, set: H5 AUX2 output configuration 1 0 17 -
• rn > 0 …
• H1 = 16 (for AUX1) or H5 = 16 (for AUX2) 17 = output managed by time band

Par. Description Def Min Max U.o.M. To activate an auxiliary output by time band, a time band needs to be
H1 AUX1 output configuration 1 0 17 - enabled by setting the following parameters:
…
16 = output in reverse mode for Par. Description Def Min Max U.o.M.
control with dead band don AUX activation by time band: day 0 0 11 days
H5 AUX2 output configuration 1 0 17 - 0 = disable
… 1, 2, …7 = Sunday, Monday, …
16 = output in reverse mode for Saturday
control with dead band 8 = Monday to Friday
9 = Monday to Saturday
10 = Saturday & Sunday
The figure shown below refers to heating/cooling control with dead 11 = every day
band for a compressor (direct) with one capacity step. hon AUX activation by time band: hours 0 0 23 hours
Mon AUX activation by time band: minutes 0 0 59 min
hoF AUX deactivation by time band: hours 0 0 23 hours
MoF AUX deactivation by time band: minutes 0 0 59 min
H8 Enable AUX activation by time band 0 0 1 -
0/1=disabled/enabled

Example: to activate auxiliary output AUX1 from Monday to Friday, from

07:30 to 20:00, set:
• H1 = 17;
t • don = 8;
• hon = 7;
Fig. 6.ac • Mon = 30;
• hoF = 20;
The following figure, on the other hand, refers to heating/cooling control • MoF = 0;
with dead band for a compressor with two capacity steps. • H8 = 1 -> if H8=0 the time band will never be active

Note: the auxiliary output is activated based on the time band

even when UltraCella is OFF

Note: lthe status of the AUX output (if configured as active by

time band) is also retained after a blackout

Fig. 6.ad

Note: the second compressor step (with or without rotation) and

control with dead band both refer to the auxiliary outputs (AUX1/
AUX2). If both are enabled, configure, for example H1 = 14 (AUX1 second
compressor step) and H5 = 16 (AUX2 output in reverse mode (heating)
with dead band)

55 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
6.17 Humidity management
UltraCella can interact with CAREL humidification systems, managing the
humidity level in combination with cooling control.
The humidity must be read from UltraCella, configuring an analogue
input (B4 or B5) as a 0 to 10 V or 4 to 20 mA input for humidity probes.
The controller can display the humidity read by the probe and, by suitably
configuring one of the auxiliary outputs, AUX1 or AUX2, activate an
external CAREL humidifier to adjust the humidity level accordingly.
Carel Humidification systems are compatible with UltraCella

humiSonic mc multizone humiDisk

Fig. 6.ae

Wiring diagram between UltraCella and humiSonic

Connection between UltraCella and humiSonic
Rx/Tx+
Rx/Tx-
GND

GND
GND
VL

humiSonic
48 47 46 45 44 43 30 B3
31 CAREL NTC, PT1000
29 B2 CAREL NTC, PT1000
28 B1 CAREL NTC, PT1000
27 Y1 analog output (0 to 10 Vdc)
49 50 51 52 53 54 26 B4 CAREL NTC, analog input 0 to 10 Vdc
25 B5
GND
Rx/Tx-
Rx/Tx+
GND
Rx/Tx-
Rx/Tx+

24 GND OUT B5 analog input

23 5 VREF 0 to 5 Vdc M (4 to 20 mA)
22 + Vdc +V
21 DI1 DI1 (**)
FieldBus BMS 20 DI2
19 DI3
42 Door switch

18
24 Vac
17
UltraCella Control
16
R6
R5 - R6 15
EN60730-1 12 (10) A
250 V 14
UL 873 12 A res. 2HP R5 DEF
12FLA 72 LRA 13
12
FAN (4)
11
R3 - R4 R4
10 A res. 10 (1) RS485
EN60730-1 5 (3) A LIGHT Supervisione
250 V 9 Supervision
UL 873 10 A res. 5FLA R3
18 LRA GND Tx Rx ON/OFF
8
R2
7
R1 - R2
EN60730-1 8 (4) A N.O. 6
250 V
UL 873 8 A res. 2FLA 5
12 LRA R1
4
3

2
1
230 V
20 A max

Fig. 6.af

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 56

 ENG
6.17.1 Analogue inputconfigurationforhumidityprobes Basic humidity control logic: if the humidity measured is less than the
Either analogue input B4 or B5 needs to be configured a humidity probe set point StH, the relay activates the externally connected humidifier
input. (REVERSE action, standard ON/OFF with differential).
Par. Description Def Min Max U.o.M. Humidity output
/P4 B4 configuration 0 0 2 - AUX1/AUX2
… ON
2 = 0 to10V
/P5 B5 configuration 0 0 1 -
… OFF
0 = 4 to 20mA
rdH B5
Par. Description Def Min Max U.o.M.
/A4 B4 configuration 0 0 4 - StH
… Fig. 6.ag
2 = humidity probe (Su) Key
/A5 B5 configuration 0 0 5 -
… StH Humidity set point
rdH Humidity differential
1 = humidity probe (Su)
B5 Probe B5 configured as 4 to 20 mA humidity probe

Example: Par. Description Def Min Max U.o.M.

Humidity probe with 0 to 10 V output -> connect the probe to input B4 StH Humidity set point 90.0 0.0 100.0 %rH
and set rdH Humidity differential 5.0 0.1 20.0 %rH
• /P4=2
• /A4=2 Note:

Humidity probe with 4 to 20 mA output -> connect the probe to input 6. If the temperature inside the cold room is less than 2°C (virtual control
B5 and set temperature Sv) -> humidifier activation (AUX1/AUX2 relay) is
• /P5=0 always disabled (with a fixed hysteresis of 1°C).
• /A5=1 7. Humidity control can be disabled during the defrost (parameter F4):
• F4=0 -> humidity control enabled based on humidity set point
StH;
• F4=1 -> humidity control not enabled: during defrost, the
6.17.2 Display humidity reading on UltraCella external humidifier will not be activated.
On models with single row display, P/Ns WB000S*, the humidity can be 8. Humidifier activation (AUX1/AUX2 relay) is always disabled in the event
displayed instead of the cold room temperature, selecting: of an alarm that immediately stops the compressor. Examples:
• Humidity probe with 0 to 10 V output -> /t1=10 (B4) • CHT alarm;
• Humidity probe with 4 to 20 mA output -> /t1 = 11 (B5) • LP alarm (after 3 times);
• IA alarm (when A6=0).
Par. Description Def Min Max U.o.M.
/t1 Variable 1 on the display 1 0 13 - Par. Description Def Min Max U.o.M.
… F4 Humidifier relay during defrost 1 0 1 -
10 = B4 0 = relay enabled in defrost (based
11 = B5 on StH)
1 = relay not enabled in defrost

On models with double row display, P/Ns WB000D*, the humidity can
be displayed on the second row as the second process selecting:
• Humidity probe with 0 to 10 V output -> /t2=10 (B4)
• Humidity probe with 4 to 20 mA output -> /t2 = 11 (B5) 6.18 Generic functions
Par. Description Def Min Max U.o.M. With UltraCella, a number of generic functions can be configured, and
/t2 Variable 2 on the display (second row) 6 0 23 - associated with configurable inputs and outputs that have not already
… been configured for other uses.
10 = B4 The following functions are available:
11 = B5 • 2 ON/OFF control functions, using outputs AUX1/AUX2
• 1 modulating control function, using 0 to 10 V output Y1
• 2 alarms, using outputs AUX1/AUX2
The generic ON/OFF or 0 to 10 V modulating control functions can be
associated with an input that also has other functions (for example Sv,
6.17.3 AUX1/AUX2auxiliaryoutputconfigurationandbasic control probe, or Su, humidity probe), or to a free input that therefore
needs to be configured specifically.
humidity control logic .
To activate the humidifier connected to UltraCella, configure one of the
auxiliary outputs AUX1 or AUX2 for humidity control. Par. Description Def Min Max U.o.M.
Par. Description Def Min Max U.o.M. /A2 Probe 2 configuration 0 0 3 -
H1 AUX1 output configuration 1 0 17 - 3 = generic temperature probe 2
… /A3 Probe 3 configuration 0 0 5 -
15 = humidity output 5 = generic temperature probe 3
H5 AUX2 output configuration 1 0 17 - /A4 Probe 4 configuration 0 0 4 -
… 3 = generic temperature probe 4
15 = humidity output 4 = generic humidity probe 4
/A5 Probe 5 configuration 0 0 5 -
2 = generic temperature probe 5
3 = generic humidity probe 5
4 = generic pressure probe 5

57 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
The generic alarm functions can be associated with an alarm already Par. Description Def Min Max U.o.M
featured on UltraCella (for example CHt, high condenser temperature H1 AUX1 output configuration 0 0 17 -
alarm, or LP, low pressure alarm), or to digital inputs D12/DI3, which 8 = Generic ON/OFF control function 1
therefore need to be configured specifically. 9 = Generic ON/OFF control function 2
H5 AUX2 output configuration 0 0 17 -
Par. Description Def Min Max U.o.M 8 = Generic ON/OFF control function 1
A5 Configuration of digital input DI2 0 0 15 - 9 = Generic ON/OFF control function 2
15 = alarm from generic function
A9 Configuration of digital input DI3 0 0 15 -
15 = alarm from generic function

6.18.1 ON/OFF control

UltraCella can manage 2 ON/OFF control functions, with direct or reverse
action and settable control set point and differential. The control variable
is defined by parameter AS1 (AS2).

Par. Description Def Min Max U.o.M.

AS1 ON/OFF control 1: control variable 3 0 14 -
configuration
0 Sm 8 generic temperature
probe 2
1 Sd1 9 generic temperature
probe 3
2 Sr 10 generic temperature
probe 4
3 Sv 11 generic temperature
probe 5
4 Sd2 12 generic humidity
Fig. 6.ah
probe 4
5 Sc 13 generic humidity
probe 5 For each ON/OFF control function, two alarm absolute thresholds and an
6 SA 14 generic pressure alarm notification delay can be set.
probe 5
7 Su Par. Description Def Min Max U.o.M
r1S ON/OFF control 1: mode 0 0 1 - AL1 ON/OFF control 1: absolute low 0,0 -50.0 200.0 °C/°F/
0/1=direct/reverse alarm threshold 0.0 100.0 rH%/
SS1 ON/OFF control 1: set point 0,0 -50,0 200,0 °C/°F/ -20.0 999 bar/psi
0,0 100,0 rH%/ AH1 ON/OFF control 1: absolute high 0 -50.0 200.0 °C/°F/
-20,0 999 bar/ alarm threshold 0.0 100.0 rH%/
psi -20.0 999 bar/psi
rS1 ON/OFF control 1: differential 2,0 0,1 20,0 °C/°F/ Ad1 ON/OFF control 1: alarm delay 0 0 250 min
rH%/ AL2 ON/OFF control 2: absolute low 0,0 -50.0 200.0 °C/°F/
bar/ alarm threshold 0.0 100.0 rH%/
psi -20.0 999 bar/psi
AH2 ON/OFF control 2: absolute high 0 -50.0 200.0 °C/°F/
AS2 ON/OFF control 2: control variable 3 0 14 -
alarm threshold 0.0 100.0 rH%/
configuration
-20.0 999 bar/psi
0 Sm 8 generic temperature Ad2 ON/OFF control 2: alarm delay 0 0 250 min
probe 2
1 Sd1 9 generic temperature The following alarms are generated by the functions:
probe 3
2 Sr 10 generic temperature
• GL1,GL2: alarms when exceeding low thresholds AL1, AL2
probe 4 • GH1, GH2: alarms when exceeding high thresholds AH1, AH2
3 Sv 11 generic temperature
probe 5 Example 1: ON/OFF control 1 based on pressure (input B5, 4 to 20 mA)
4 Sd2 12 generic humidity with direct action via AUX1. Control set point 15 bars, differential 3 bars.
probe 4 Set:
5 Sc 13 generic humidity • /P5 = 0 -> input B5 to 4 to 20 mA
probe 5 • /A5 = 4 -> generic pressure probe 5
6 SA 14 generic pressure • AS1 = 14 -> generic pressure probe 5
probe 5
7 Su
• r1S = 0 -> direct action
r2S ON/OFF control 2: mode 0 0 1 -
• SS1 = 15 -> control set point 15 bars
0/1=direct/reverse
• rS1 = 3 -> differential 3 bars
SS2 ON/OFF control 2: set point 0,0 -50,0 200,0 °C/°F/ • H1 = 8 -> output AUX1 for ON/OFF control 1
0,0 100,0 rH%/
-20,0 999 bar/
psi Example 2: ON/OFF control 2 based on humidity (input B4, 0 to 10 V) with
rS2 ON/OFF control 2: differential 2,0 0,1 20,0 °C/°F/ reverse action on AUX2. Control set point 75% rH, differential 10% rH.
rH%/ Set:
bar/ • /P4 = 2 -> input B4 to 0 to 10 V
psi • /A4 = 4 -> generic humidity probe 4
• AS2 = 12 -> generic humidity probe 4
To enable the function, set AS1/AS2 to a value greater than 0. To use • r2S = 1 -> reverse action
outputs AUX1/AUX2 for generic ON/OFF functions, set parameters H1/ • SS2 = 75 -> control set point 75% rH
H5. • rS2 = 10 -> differential 10% rH
• H5 = 9 -> output AUX2 for ON/OFF control 2

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 58

 ENG
6.18.2 Modulating control
UltraCella can manage a modulating control function using a 0 to 10 V
analogue output with direct or reverse action and settable control set reverse modulation (r1M= 1)
SH1= MAX
point and differential. The control variable is defined by parameter AM1,
the control range by parameter rM1.

Par. Description Def Min Max U.o.M.

AM1 Modulating control: control variable 3 0 14 - SL1= MIN
(cut-off )
configuration
0 Sm 8 generic temperature
probe 2
1 Sd1 9 generic temperature regulation variable
probe 3 rM1 rc1
2 Sr 10 generic temperature
probe 4 SM1
3 Sv 11 generic temperature
probe 5 Fig. 6.aj
4 Sd2 12 generic humidity
probe 4 Also for modulating control, two alarm absolute thresholds and an alarm
5 Sc 13 generic humidity notification delay can be set.
probe 5
6 SA 14 generic pressure
Par. Description Def Min Max U.o.M.
probe 5
AL3 Modulating control: absolute low 0,0 -50.0 200.0 °C/°F/
7 Su
alarm threshold 0.0 100.0 rH%/
r1M Modulating control: mode 0 0 1 -
-20.0 999 bar/psi
0/1=direct/reverse AH3 Modulating control: absolute 0,0 -50.0 200.0 °C/°F/
SM1 Modulating control: set point 0,0 -50,0 200,0 °C/°F/ 0.0 100.0 rH%/
high alarm threshold
0,0 100,0 rH%/ -20.0 999 bar/psi
-20,0 999 bar/ Ad3 Modulating control: alarm delay 0 0 250 min
psi
rc1 Modulating control: differential 2,0 0,1 20,0 °C/°F/
rH%/
The following alarms are generated by the functions:
bar/
psi • GL3: alarm when exceeding low threshold AL3
rM1 Modulating control: modulation range, 2,0 0,1 40,0 °C/°F/ • GH3: alarm when exceeding high threshold AH3
between min SL1 and max SH1 rH%/
bar/
psi Example: 0 to 10 V modulating control based on pressure (input B5, 4
to 20 mA) with direct action, control set point 10 bars, differential 1 bar,
modulation range 8 bars, minimum output 2 V, maximum output 8 V.
The maximum and minimum values can be set using parameters SH1 Set:
and SL1 (cut-off ), as a percentage of the range from 0 to 10 V.. • /P5 = 0 -> input B5 to 4 to 20 mA
• /A5 = 4 -> generic pressure probe 5
Par. Description Def Min Max U.o.M. • AM1 = 14 -> generic pressure probe 5
SL1 Modulating control: min. modulating 0,0 0,0 SH1 % • r1M = 0 -> direct action
output value (cut-off ) • SM1 = 10 -> control set point 10 bars
SH1 Modulating control: max. modulating 100,0 SL1 100,0 % • rc1 = 1 -> differential 1 bar
output value • rM1 = 8 -> modulation range 8 bars
• SL1 = 20,0 -> minimum output 2 V
• SH1 = 80,0 -> maximum output 8 V
To enable the function, set AM1 to a value greater than 0. To use the • HO1 = 1 -> 0 to 10 V output Y1 for generic modulating function
0 to 10 V analogue output Y1 for the generic modulating function, set
parameter HO1.

Par. Description Def Min Max U.o.M.

HO1 Configuration of output Y1 0 0 3 - 6.18.3 Generic alarms
1 = modulating output 1 (generic UltraCella can manage up to two generic alarms, associated with alarms
function) that are already featured (for example CHt, high condenser temperature
alarm, or LP, low pressure alarm), or to digital inputs D12/DI3, which
therefore need to be specifically configured. The source of the alarm is
defined by parameter AA1 (AA2), the notification delay by parameter Ad4
(Ad5).
SH1= MAX direct modulation (r1M= 0)
If the generic alarm is associated with digital input DI2 (for AA1) or DI3
(for AA2), the operating logic can be selected (normally open/normally
closed):
SL1= MIN
(cut-off ) • r1A (r2A) = 0 -> N.O. logic -> alarm if DI2 (DI3) is closed (active)
• r1A (r2A) = 1 -> N.C.logic -> alarm if DI2 (DI3) is open (not active)
regulation variable

rc1 rM1
SM1 Fig. 6.ai

59 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
Par. Description Def Min Max U.o.M.
AA1 Alarm 1: select source 0 0 11 -
0 DI2 (with A5=15)
1 Virtual probe (Sv) fault (rE)
2 Probe S1 (Sm) fault (E0)
3 Probe S2 fault (E1)
4 Probe S3 fault (E2)
5 Probe S4 fault (E3)
6 Probe S5 fault (E4)
7 Low pressure alarm (LP)
8 Immediate external alarm (IA)
9 Low temperature alarm (LO)
10 High temperature alarm (HI)
11 High condenser temperature
alarm (CHt)
r1A Alarm 1: logic 0 0 1 -
0/1=normally open/normally
closed
Ad4 Alarm 1: delay 0 0 250 min
AA2 Alarm 2: select source 0 0 11 -
0 DI3 (with A9=15)
1 Virtual probe (Sv) fault (rE)
2 Probe S1 (Sm) fault (E0)
3 Probe S2 fault (E1)
4 Probe S3 fault (E2)
5 Probe S4 fault (E3)
6 Probe S5 fault (E4)
7 Low pressure alarm (LP)
8 Immediate external alarm (IA)
9 Low temperature alarm (LO)
10 High temperature alarm (HI)
11 High condenser temperature
alarm (CHt)
r2A Alarm 2: logic 0 0 1 -
0/1=normally open/normally
closed
Ad5 Alarm 2: delay 0 0 250 min

The following alarms are generated by the functions:

• GA1: alarm relating to function AA1
• GA2: alarm relating to function AA2

To associate the generic alarm to a digital input, DI2 or DI3, set parameter
A5 or A9.

Par. Description Def Min Max U.o.M.

A5 Digital input 2 configuration (DI2) 0 0 15 -
15 = alarm from generic function
A9 Digital input 3 configuration (DI3) 0 0 15 -
15 = alarm from generic function

To use outputs AUX1/AUX2 for the generic alarms, set parameters H1/H5.

Par. Description Def Min Max U.o.M.

H1 AUX1 output configuration 0 0 17 -
10 = generic alarm 1 (GA1)
11 = generic alarm 2 (GA2)
H5 AUX2 output configuration 0 0 17 -
10 = generic alarm 1 (GA1)
11 = generic alarm 2 (GA2)

Example: AUX1 active for alarm from digital input DI3 with N.C. logic,
delay 15 minutes.
Set:
• AA2 = 0 -> Alarm 2 associated with digital input DI3
• r2A = 1 -> N.C. logic
• Ad5 = 15 -> delay 15 minutes
• A9 = 15 -> DI3 for alarm from generic function
• H1 = 11 -> AUX1 for generic alarm 2

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 60

 ENG
7. PARAMETERS TABLE
Type of variable: A = analogue, I = integer, D = digital

Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP
Pro
/21 Probe measurement stability probe 1 4 0 9 - I 12 51 R/W 37
/22 Probe measurement stability probe 2 4 0 9 - I 13 52 R/W 37
/23 Probe measurement stability probe 3 4 0 9 - I 14 53 R/W 37
/24 Probe measurement stability probe 4 4 0 9 - I 15 54 R/W 37
/25 Probe measurement stability probe 5 4 0 9 - I 16 55 R/W 37
/4 Virtual probe composition 0 0 100 - I 17 56 R/W 44
0 = probe B1
100= probe B2
/5t Temperature unit of measure 0 0 1 - I 18 57 R/W 38
0/1 = °C / °F
/5P Pressure unit of measure 0 0 1 - I 19 58 R/W 38
0/1 = bar/psi
/6 Display decimal point 0 0 1 - D 19 8 R/W 38
0/1 = yes/no
/t1 Display variable 1 1 0 13 - I 67 106 R/W 38
0 None 7 B1 57
1 Virtual probe (Sv) 8 B2
2 Outlet probe (Sm) 9 B3
3 Intake probe (Sr) 10 B4
4 Defrost probe 1 (Sd1) 11 B5
5 Defrost probe 2 (Sd2) 12 Condenser probe (Sc)
6 Set point 13 Variable speed condenser fans
set point
/t2 Display variable 2 (*) 6 0 23 - I 68 107 R/W 38
0 None. 12 rd 57
1 Virtual probe (Sv) 13 Superheat (EVO)
2 Outlet probe (Sm) 14 Valve opening % (EVO)
3 Intake probe (Sr) 15 Valve opening step (EVO)
4 Defrost probe 1 (Sd1) 16 Condenser probe (Sc)
5 Defrost probe 2 (Sd2) 17 U1 probe (3ph model)
6 Set point 18 U2 probe (3ph model)
7 B1 19 U3 probe (3ph model)
8 B2 20 Variable speed condenser fans
set point (Y1)
9 B3 21 Superheat (EVDice))
10 B4 22 Valve opening % (EVDice)
11 B5 23 Step valve opening (EVDice)
(*) can be viewed only on UltraCella Sevice Terminal or on the controller
with double row display
/P Type B1 to B3 0 0 2 - I 20 59 R/W 34
0 NTC Standard range -50T90°C
1 NTC extended range 0T150°C
2 PT1000
/A2 B2 configuration 1 0 3 - I 21 60 R/W 34
0 Absent
1 Defrost probe 1 (Sd1)
2 Intake probe (Sr)
3 Generic function on probe 2
/A3 B3 configuration 0 0 5 - I 22 61 R/W 34
0 Absent
1 Defrost probe 2 (Sd2)
2 Condenser probe (Sc)
3 Defrost probe 1 (Sd1)
4 Ambient temperature probe (SA)
5 Generic function on probe 3
/P4 B4 type 0 0 2 - I 23 62 R/W 34
0 NTC Standard range -50T90°C 57
1 NTC Extended range 0T150°C
2 0 to 10 V
/A4 B4 configuration 0 0 4 - I 24 63 R/W 34
0 Absent 57
1 Ambient temperature probe (SA)
2 Humidity probe
3 Probe 4 generic temperature
4 Probe 4 generic humidity
/P5 B5 type 0 0 1 - I 25 64 R/W 34
0 4 to 20 mA 57
1 0 to 5 Vrat
/A5 B5 configuration 0 0 5 - I 26 65 R/W 34
0 Absent 57
1 Humidity probe
2 Probe 5 generic temperature
3 Probe 5 generic humidity
4 Probe 5 generic pressure
5 Scp (Condensing pressure probe)

61 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP
/4L Probe 4 minimum value 0 -50.0 /4H - A 98 208 R/W 34
/4H Probe 4 maximum value 100 /4L 200 - A 99 209 R/W 34
/5L Probe 5 minimum value 0 -50.0 /5H - A 100 210 R/W 34
/5H Probe 5 maximum value 100 /5L 999 - A 101 211 R/W 34
/C1 Offset B1 0 -20.0 20.0 °C/°F A 7 0 R/W 34
/C2 Offset B2 0 -20.0 20.0 °C/°F A 8 1 R/W 34
/C3 Offset B3 0 -20.0 20.0 °C/°F A 9 2 R/W 34
/C4 Offset B4 0 -20.0 20.0 °C/°F/ A 10 3 R/W 34
%rH
/C5 Offset B5 0 -20.0 20.0 °C/°F/ A 11 4 R/W 34
%rH/
bar/psi

CtL
St Set point 0 r1 r2 °C/°F A 12 5 R/W 44
rd Differential 2.0 0.1 20 °C/°F A 13 6 R/W 44
r1 Minimum set point -50.0 -50.0 r2 °C/°F A 14 7 R/W 44
r2 Maximum set point 60.0 r1 200 °C/°F A 15 8 R/W 44
r3 Operating mode 0 0 1 - D 11 0 R/W 44
0 direct with defrost
1 direct without defrost
rn Dead band 3,0 -20,0 20,0 °C/°F A 80 190 R/W 55
rr Differential for control with dead band 2,0 0,1 20 °C/°F A 81 191 R/W 55
r4 Offset set point 60.0 r1 200 °C/°F A 82 192 R/W 45
StH Humidity set point 90.0 0.0 100.0 %rH A 28 19 R/W 58
rdH Humidity differential 5.0 0.1 20.0 %rH A 29 20 R/W 58
PS1 Ramps: final set point, phase 1 0 -50.0 200.0 °C/°F A 77 187 R/W 45
PS2 Ramps: final set point, phase 2 0 -50.0 200.0 °C/°F A 78 188 R/W 45
PS3 Ramps: final set point, phase 3 -30.0 -50.0 -200.0 - A 79 189 R/W 45
PH1 Ramps: duration of phase 1 6 0 10 days A 102 212 R/W 45
PH2 Ramps: duration of phase 2 2 0 10 days A 103 213 R/W 45
PH3 Ramps: duration of phase 3 10 0 10 days A 104 214 R/W 45
Pdt Ramps: maximum set point variation after blackout 20.0 10.0 30.0 °C/°F A 106 216 R/W 46
Pon Enable set point ramps 0 0 1 - D 159 48 R/W 46
0/1 = ramps disabled/enabled

CMP
c0 Compressors/fan start delay at power on 0 0 15 min I 31 70 R/W 43
c1 Minimum time between compressor starts 6 0 30 min I 32 71 R/W 37
c2 Minimum compressor off time 3 0 15 min I 33 72 R/W 37
c3 Minimum compressor on time 3 0 15 min I 34 73 R/W 37
c4 Compressor running time in duty setting 0 0 100 min I 35 74 R/W 53
cc Continuous cycle duration 0 0 15 hours I 36 75 R/W 47
c6 Low temperature alarm delay after continuous cycle 2 0 250 hours I 37 76 R/W 47
c7 Maximum pump down (PD) time 0 0 900 s I 38 77 R/W 46
0 = Pump down disabled
c8 Compressor start delay after opening of pump down valve 5 0 60 s I 39 78 R/W 46
c9 Autostart in pump down 0 0 1 - D 13 2 R/W 47
0/1 = whenever pump down valve closes/ whenever pump down valve
closes & every request of low pressure switch without regulation request
c10 Pump down by time/pressure 0 0 1 - D 12 1 R/W 47
0/1 = pressure/ time
c11 Second compressor start delay 4 0 250 s I 40 79 R/W 43
FC4 Condenser fan deactivation temperature 40.0 -50.0 200.0 °C/°F A 16 9 R/W 52
FCH Variable speed condenser fans: max. output value 100 FCL 100 % A 131 241 R/W 52
FCL Variable speed condenser fans: min. output value 0 0 FCH % A 132 242 R/W 52
FCn Variable speed condenser fans: min. capacity % 0 0 FCH % A 133 243 R/W 52
FCS Variable speed condenser fans: set point 15.0 -100.0 200.0 °C/°F A 134 244 R/W 52
FCd Variable speed condenser fans: differential 2.0 0.1 10.0 °C/°F A 135 245 R/W 52
FCt Variable speed condenser fans: fixed or floating set point 0 0 1 - D 167 56 R/W 53
0/1= FCS fixed/floating
FSH Floating condensing temp. set point: max value 25.0 FSL 200.0 °C/°F A 136 246 R/W 53
FSL Floating condensing temp. set point: min value 5.0 -100.0 FSH °C/°F A 137 247 R/W 53
FSO Floating condensing temp. set point: offset 5.0 -50.0 50.0 °C/°F A 138 248 R/W 53

dEF
d0 Type of defrost 0 0 3 - I 41 80 R/W 36
0 Heater by temperature 48
1 Hot gas by temperature
2 Heater by time
3 Hot gas by time
dI Max interval between consecutive defrosts 8 0 250 hours I 42 81 R/W 49
0 = defrost not performed
dt1 End defrost temperature, main evaporator 4.0 -50.0 200.0 °C/°F A 17 10 R/W 36
48
dt2 End defrost temperature, auxiliary evaporator 4.0 -50.0 200.0 °C/°F A 18 11 R/W 48
dP1 Maximum defrost duration 30 1 250 min I 43 82 R/W 36
48
dP2 Maximum defrost duration, auxiliary evaporator 30 1 250 min I 44 83 R/W 45
dd Dripping time after defrost 2 0 30 min I 45 84 R/W 36
d3 Defrost activation delay 0 0 250 min I 46 85 R/W 50

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 62

 ENG
Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP
dpr Defrost priority over continuous cycle 0 0 1 - D 15 4 R/W 50
0/1 = no/yes
d4 Defrost at start-up 0 0 1 - D 14 3 R/W 50
0/1=no/yes
d5 Defrost delay at start-up 0 0 250 min I 47 86 R/W 50
d6 Terminal display during defrost 1 0 2 - I 49 88 R/W 48
0 Temperature alternated with dEF 25
1 Last temperature shown before defrost
2 dEF
d8 High temperature alarm delay after defrost (and door open) 1 0 250 hours I 48 87 R/W 50

ALM
A0 Alarm and fan differential 2.0 0.1 20.0 °C/°F A 19 12 R/W 52
73
A1 Alarm thresholds (AL, AH) relative to set point or absolute 0 0 1 - D 16 5 R/W 73
0/1=relative/absolute
AL Low temperature alarm threshold 0.0 -50.0 200.0 °C/°F A 20 13 R/W 73
If A1=0, AL=0: alarm disabled
If A1=1, AL=-50: alarm disabled
AH High temperature alarm threshold 0.0 -50.0 200.0 °C/°F A 21 14 R/W 73
If A1=0, AH=0: alarm disabled
If A1=1, AH=200: alarm disabled
Ad High/low temperature alarm delay 120 0 250 min I 50 89 R/W 73
A5 Digital input 2 (DI2) configuration 0 0 15 - I 51 90 R/W
0 Not active 8 Low pressure switch 35
1 Immediate external alarm 9 Do not select 45
2 Do not select 10 Do not select 47
3 Enable defrost 11 Do not select 58
4 Start defrost 12 AUX1 activation 60
5 Do not select 13 Do not select
6 Remote ON/OFF 14 Continuous cycle activation
7 Do not select 15 Alarm from generic funcion
A6 Stop compressor on external alarm 0 0 100 min I 53 92 R/W 73
A7 Low pressure (LP) alarm delay 1 0 250 min I 54 93 R/W 36
A8 Enable Ed1 and Ed2 alarms 0 0 1 - D 168 57 R/W 48
0/1= disabled/enabled alarms
A9 Digital input 3 (DI3) configuration 0 0 15 - I 52 91 R/W 35
0 Not active 8 Low pressure switch 45
1 Immediate external alarm 9 Do not select 47
2 Do not select 10 Do not select 58
3 Enable defrost 11 Do not select 60
4 Start defrost 12 AUX2 activation
5 Do not select 13 Do not select
6 Remote ON/OFF 14 Continuous cycle activation
7 Change set point 15 Alarm from generic funcion
A10 Low pressure alarm delay (LP), compressor running 3 0 60 min I 55 94 R/W
Ac High temperature condenser alarm threshold 70.0 -50.0 200.0 °C/°F A 22 15 R/W 74
Acd High temperature condenser alarm delay 0 0 250 min I 56 95 R/W 74
ULL Absolute low umidity alarm threshold 0 0 100.0 %rH A 84 194 R/W 73
0= alarm disabled
UHL Absolute high umidity alarm threshold 100.0 0 100.0 %rH A 83 193 R/W 73
100= alarm disabled
AdH Humidity alarms AUH, AUL delay 120 0 250 min A 117 227 R/W 73

Fan
F0 Evaporator fan management 0 0 2 - I 174 265 R/W 50
0 always on with compressor on 51
1 activation depends on Sd, Sv
2 variable speed fans
F1 Fan activation temperature 5.0 -50.0 200.0 °C/°F A 23 16 R/W 50
Frd Fan activation differential 2.0 0.1 20.0 °C/°F A 24 17 R/W 50
F2 Fan activation time with compressor off 30 0 60 min I 57 96 R/W 50
51
F3 Evaporator fan during defrost 1 0 1 - D 17 6 R/W 36
0/1= ON/OFF
Fd Post dripping time 1 0 30 min I 60 99 R/W 36
F4 Humidity output during defrost 1 0 1 - D 71 28 R/W 51
0/1 = ON/OFF 58
F5 Evaporator fans cut-off temperature (hysteresis 1°C) 15 -50 200 °C/°F A 25 18 R/W 51
F6 Maximum fan speed 100 F7 100 % I 58 97 R/W 51
F7 Minimum fan speed 0 0 F6 % I 59 98 R/W 51
F8 Fans peak time 0 0 240 s I 176 175 R/W 51
0 = disabled function
F10 Evaporator fans forcing time at maximum speed 0 0 240 min I 177 176 R/W 51
0 = disabled function
CnF
H0 Serial address 193 0 247 - I 69 108 R 38
In Type of unit 0 0 0 - - - - R

63 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP
H1 AUX1 output configuration 1 0 17 - I 61 100 R/W 38
0 Normally energized alarm 9 ON/OFF control output 2 43
1 Normally deenergized alarm 10 Alarm 1 output 46
2 Activation by AUX1 key or DI 11 Alarm 2 output 52
3 Bowl resistance activation 12 Do not select 53
4 Auxiliary evaporator defrost 13 Second compressor step 54
5 Pump down valve 14 Second compressor step with
55
rotation
56
6 Condenser fan 15 Humidity output
7 Delayed compressor 16 Reverse mode output 58
8 ON/OFF control output 1 17 Output managed by time band 59
61
H4 Buzzer 0 0 1 - D 21 10 R/W 38
0/1 = enabled/ disabled
H5 AUX2 output configuration 1 0 17 - I 62 101 R/W 38
0 Normally energized alarm 9 ON/OFF control output 2 43
1 Normally deenergized alarm 10 Alarm 1 output 46
2 Activation by AUX1 key or DI 11 Alarm 2 output 52
3 Bowl resistance activation 12 Do not select 53
4 Auxiliary evaporator defrost 13 Second compressor step 54
5 Pump down valve 14 Second compressor step with
55
rotation
56
6 Condenser fan 15 Humidity output
7 Delayed compressor 16 Reverse mode output 58
8 ON/OFF control output 1 17 Output managed by time band 59
61
H6 Terminal keys block configuration 0 0 255 - I 70 109 R/W 38
0 all keys enabled
1 Set point modification
2 Defrost
4 -
8 AUX1 output
16 PRG+SET (menu)
32 AUX2 output
64 ON/OFF management
128 Light management
255 all keys disabled
HO1 Output Y1 configuration 0 0 3 - I 63 102 R/W 43
0 Not active 51
1 Modulating output 1 (generic function) 52
2 Variable speed evaporator fans set on Sd probe 60
3 Variable speed condenser fans
H7 BMS protocol selection 0 0 1 - I 188 180 R/W 18
0= Carel 38
1= Modbus
H10 BMS baud rate bit/s 4 0 9 - A 165 266 R/W 18
0 1200 5 38400
1 2400 6 57600
2 4800 7 76800
3 9600 8 115200
4 19200 9 375000
H11 BMS stop bits 2 1 2 - A 166 267 R/W 18
1 1 bit di stop
2 2 di bit di stop
H12 BMS parity 0 0 2 - A 167 268 R/W 18
1 odd
2 even
tr1 First temperature to be recorded 0 0 8 - I 189 181 R/W 29
0 No log 5 Sd2
1 Sv 6 Sc
2 Sm 7 SA
3 Sr 8 Su
4 Sd1
tr2 Second temperature to be recorded 0 0 8 - I 190 182 R/W 29
0 No log 5 Sd2
1 Sv 6 Sc
2 Sm 7 SA
3 Sr 8 Su
4 Sd1
trc Sample time temperature recording 5 2 60 min I 191 183 R/W 29

HcP
HCE Enable HACCP 0 0 1 - D 22 11 R/W 74
0/1 = No/Yes
Htd HACCP alarm delay 0 0 250 min I 71 110 R/W 74

rtC
tcE Enable data modification 0 0 1 - D 24 13 R/W 23
tcT Date/ time change 0 0 1 - D 25 14 R/W 23
Action on variation 01 o 10
y__ Date/ time: year 0 0 37 - I 98 111 R/W 23
UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 64
 ENG
Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP
M__ Date/ time: month 1 1 12 - I 99 112 R/W 23
d__ Date/ time : day of month 1 1 31 - I 100 113 R/W 23
h__ Date/ time: hour 0 0 23 - I 101 114 R/W 23
n__ Date/ time: minute 0 0 59 - I 102 115 R/W 23
tcL Hours/minutes visualization on the second row for models with two rows 0 0 1 - D 72 29 R/W 66
display 0/1=no/yes
ddi Defrost i (i=1…8): day 0 0 11 days I 103…110 116...123 R/W 48
hhi Defrost i (i=1…8): hour 0 0 23 hours I 111…118 124...131 R/W 48
nni Defrost i (i=1…8): minute 0 0 59 min I 119…126 132...139 R/W 48
don AUX activation by time band: day 0 0 11 days A 105 215 R/W 56
hon AUX activation by time band: hours 0 0 23 hours A 107 217 R/W 56
Mon AUX activation by time band: minutes 0 0 59 min A 109 219 R/W 56
hoF AUX deactivation by time band: hours 0 0 23 hours A 108 218 R/W 56
MoF AUX deactivation by time band: minutes 0 0 59 min A 110 220 R/W 56
H8 Enable AUX activation by time band 0 0 1 - D 160 49 R/W 56
0/1=disabled/enabled
dSn Set point variation by time band: day 0 0 11 days A 111 221 R/W 45
hSn Start set point variation by time band: hours 0 0 23 hours A 113 223 R/W 45
MSn Start set point variation by time band: minutes 0 0 59 min A 115 225 R/W 45
hSF End set point variation by time band: hours 0 0 23 hours A 114 224 R/W 45
MSF End set point variation by time band: minutes 0 0 59 min A 116 226 R/W 45
H9 Enable set point variation by time band 0 0 1 - D 161 50 R/W 45
0/1=disabled/enabled

doL
c12 Compressor safety time for door switch 5 0 5 min I 64 103 R/W 36
0 = disable door management
d8d Compressor restart time for door switch 30 c12 240 min I 65 104 R/W 36
A3 Disable door microswitch 1 0 1 - D 138 45 R/W 35
0 = door microswitch enabled
1 = door microswitch disabled
tLi Light on with door open 120 0 240 min I 66 105 R/W 37
A4 Light management 0 0 1 - D 18 7 R/W 37
0 = door switch + light key - 1 = light key
rcP (see chapter 3 the procedure for setting parameters to default values)

GEF
AS1 ON/OFF control 1: control variable configuration 3 0 14 - A 119 229 R/W 58
0 Sm 8 probe 2 generic temperature
1 Sd1 9 probe 3 generic temperature
2 Sr 10 probe 4 generic temperature
3 Sv 11 probe 5 generic temperature
4 Sd2 12 probe 4 generic humidity
5 Sc 13 probe 5 generic humidity
6 SA 14 probe 5 generic pressure
7 Su
r1S ON/OFF control 1: mode 0 0 1 - D 162 51 R/W 58
0/1=direct/reverse
SS1 ON/OFF control 1: set point 0.0 -50.0 200.0 °C/°F/ A 85 195 R/W 58
0.0 100.0 rH%/
-200.0 999 bar/psi
rS1 ON/OFF control 1: differential 2.0 0.1 20.0 °C/°F/ A 87 197 R/W 58
rH%/
bar/psi
AL1 ON/OFF control 1: absolute low alarm threshold 0.0 -50.0 200.0 °C/°F/ A 89 199 R/W 59
0.0 100.0 rH%/
-200.0 999 bar/psi
AH1 ON/OFF control 1: absolute high alarm threshold 0.0 -50.0 200.0 °C/°F/ A 91 201 R/W 59
0.0 100.0 rH%/
-200.0 999 bar/psi
Ad1 ON/OFF control 1: alarm delay 0 0 250 min A 121 231 R/W 59
AS2 ON/OFF control 2: control variable configuration 3 0 14 - A 120 230 R/W 58
0 Sm 8 probe 2 generic temperature
1 Sd1 9 probe 3 generic temperature
2 Sr 10 probe 4 generic temperature
3 Sv 11 probe 5 generic temperature
4 Sd2 12 probe 4 generic humidity
5 Sc 13 probe 5 generic humidity
6 SA 14 probe 5 generic pressure
7 Su
r2S ON/OFF control 2: mode 0 0 1 - D 163 52 R/W 58
0/1=direct/reverse
SS2 ON/OFF control 2: set point 0.0 -50.0 200.0 °C/°F/ A 86 196 R/W 58
0.0 100.0 rH%/
-200.0 999 bar/psi
rS2 ON/OFF control 2: differential 2.0 0.1 20.0 °C/°F/ A 88 198 R/W 58
rH%/
bar/psi
AL2 ON/OFF control 2: absolute low alarm threshold 0.0 -50.0 200.0 °C/°F/ A 90 200 R/W 59
0.0 100.0 rH%/
-200.0 999 bar/psi

65 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP
AH2 ON/OFF control 2: absolute high alarm threshold 0.0 -50.0 200.0 °C/°F/ A 92 202 R/W 59
0.0 100.0 rH%/
-200.0 999 bar/psi
Ad2 ON/OFF control 2: alarm delay 0 0 250 min A 122 232 R/W 59
AM1 Modulating control: control variable configuration 3 0 14 - A 123 233 R/W 59
0 Sm 8 probe 2 generic temperature
1 Sd1 9 probe 3 generic temperature
2 Sr 10 probe 4 generic temperature
3 Sv 11 probe 5 generic temperature
4 Sd2 12 probe 4 generic humidity
5 Sc 13 probe 5 generic humidity
6 SA 14 probe 5 generic pressure
7 Su
r1M Modulating control: mode 0 0 1 - D 164 53 R/W 59
0/1=direct/reverse
SM1 Modulating control: set point 0.0 -50.0 200.0 °C/°F/ A 93 203 R/W 59
0.0 100.0 rH%/
-200.0 999 bar/psi
rc1 Modulating control: differential 2.0 0.1 20.0 °C/°F/ A 94 204 R/W 59
rH%/
bar/psi
rM1 Modulating control: modulation range, between min SL1 and max SH1 2.0 0.1 40.0 °C/°F/ A 95 205 R/W 59
rH%/
bar/psi
SL1 Modulating control: min. modulating output value (cut-off ) 0.0 0.0 SH1 % A 125 235 R/W 59
SH1 Modulating control: max. modulating output value 100.0 SL1 100.0 % A 124 234 R/W 59
AL3 Modulating control: absolute low alarm threshold 0.0 -50.0 200.0 °C/°F/ A 96 206 R/W 60
0.0 100.0 rH%/
-200.0 999 bar/psi
AH3 Modulating control: absolute high alarm threshold 0.0 -50.0 200.0 °C/°F/ A 97 207 R/W 60
0.0 100.0 rH%/
-200.0 999 bar/psi
Ad3 Modulating control: alarm delay 0 0 250 min A 126 236 R/W 60
AA1 Alarm 1: select source 0 0 11 - A 127 237 R/W 60
0 DI2 (with A5=15) 6 Probe S5 fault (E4)
1 Virtual probe (Sv) fault (rE) 7 Low pressure alarm (LP)
2 Probe S1 (Sm) fault (E0) 8 Immediate external alarm (IA)
3 Probe S2 fault (E1) 9 Low temperature alarm (LO)
4 Probe S3 fault (E2) 10 High temperature alarm (HI)
5 Probe S4 fault (E3) 11 High condenser temperature alarm (CHt)
r1A Alarm 1: logic 0 0 1 - D 165 54 R/W 60
0/1=normally open/normally closed
Ad4 Alarm 1: delay 0 0 250 min A 129 239 R/W 60
AA2 Alarm 2: select source 0 0 11 - A 128 238 R/W 60
0 DI3 (with A9=15) 6 Probe S5 fault (E4)
1 Virtual probe (Sv) fault (rE) 7 Low pressure alarm (LP)
2 Probe S1 (Sm) fault (E0) 8 Immediate external alarm (IA)
3 Probe S2 fault (E1) 9 Low temperature alarm (LO)
4 Probe S3 fault (E2) 10 High temperature alarm (HI)
5 Probe S4 fault (E3) 11 High condenser temperature alarm (CHt)
r2A Alarm 2: logic 0 0 1 - D 166 55 R/W 60
0/1=normally open/normally closed
Ad5 Alarm 2: delay 0 0 250 min A 130 240 R/W 60

EVO
P1 Enable communication with EVD EVO module 0 0 1 - D 70 27 R/W 39
0/1=no/yes
P1t S1 probe type 0 0 3 - I 139 150 R/W 39
0 RAZ. 0 to 5 V 2 4 to 20 mA remote
1 4 to 20 mA 3 4 to 20 mA external
P1M Max value of S1 probe 12.8 -20 200 °C/°F A 31 22 R/W 39
P1n Min value of S1 probe -1 -20 200 °C/°F A 30 21 R/W 39
PVt Valve type 1 1 22 - I 136 147 R/W 39
1 CAREL EXV 12 Sporlan seh 100
2 Alco ex4 13 Sporlan seh 175
3 Alco ex5 14 Danfoss ets 12.5 - 25b
4 Alco ex6 15 Danfoss ets 50b
5 Alco ex7 16 Danfoss ets 100b
6 Alco ex8 330hz CAREL recommended 17 Danfoss ets 250
7 Alco ex8 500hz Alco specification 18 Danfoss ets 400
8 Sporlan sei 0.5-11 19 2 CAREL EXV connected
together
9 Sporlan ser 1.5-20 20 Sporlan ser(i) g, j, k
10 Sporlan sei 30 21 Danfoss ccm 10-20-30
11 Sporlan sei 50 22 Danfoss ccm 40

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 66

 ENG
Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP
PH Refrigerant type 3 1 25 - I 135 146 R/W 39
1 R22 6 R507A 11 R744 16 R413A 21 R245Fa
2 R134a 7 R290 12 R728 17 R422A 22 R407F
3 R404A 8 R600 13 R1270 18 R423A 23 R32
4 R407C 9 R600a 14 R417A 19 R407A 24 HTR01
5 R410A 10 R717 15 R422D 20 R427A 25 HTR02
PrE Main regulation type 2 1 4 - I 137 148 R/W 39
1 centralized cabinet cold room 3 perturbated cabinet cold room
2 self contained cabinet cold room 4 subcritical CO2 cabinet/cold room
P0 EVD Modbus address 198 1 247 - I 134 145 R/W 39
P3 Superheat setpoint 10 -72 324 K A 44 35 R/W 39
P4 Proportional gain 15 0 800 - A 36 27 R/W 39
P5 Integral time 150 0 999 sec A 148 159 R/W 39
P6 Derivative time 2 0 800 sec A 37 28 R/W 39
P7 LowSH: threshold low superheat 3 -72 324 K A 45 36 R/W 39
P8 Low Superheat protection integral time 600 0 800 sec A 38 29 R/W 39
P9 LowSH: low superheat alarm delay 600 0 999 sec A 150 161 R/W 39
PL1 LOP: threshold for low temperature of evaporation -50 -60 200 °C/°F A 64 41 R/W 39
PL2 LOP: integral time 600 0 800 sec A 39 30 R/W 39
PL3 LOP: low evaporation temperature alarm delay 600 0 999 sec A 151 162 R/W 39
PM1 MOP: threshold for low temperature of evaporation 50 -60 200 °C/°F A 47 38 R/W 39
PM2 MOP: integral time 600 0 800 sec A 40 31 R/W 39
PM3 MOP: low evaporation temperature alarm delay 10 0 999 sec I 152 163 R/W 39
cP1 Open valve startup (percentage) 50 0 100 % A 146 157 R/W 39
Pdd Post defrost delay, (only for single driver) 10 0 60 min A 147 158 R/W 39
PSb Valve position in stand-by 0 0 100 step A 169 174 R/W 39
PMP Enable manual positioning 0 0 1 - D 103 38 R/W 39
PMu Manual valve positioning 0 0 999 step I 162 173 R/W 39
Pnr Reset EVD setting 0 -> 1 Reset all EVD parameters 0 0 1 - D 139 46 R/W 39

ICE
IPE Enable EVDice communication 0 0 1 - D 183 59 R/W 39
0/1 = not enabled/ enabled
IrE 1= Multiplexed cabinet/cold room 1 1 6 - I 196 185 R/W 40
2= Air-conditioner/chiller with plate heat exchanger (2, 3, 4, 5
& 6 mode
3= Air-conditioner/chiller with tube bundle heat exchanger select.
4= Air-conditioner/chiller with finned coil heat exchanger only from
UltraCella
5= Reserved service
6= Reserved pGD)
IP3 Superheat set point 11 IC1 99 K A 150 255 R/W 40
PH 1 R22 6 R507A 11 R744 16 R413A 21 R245Fa 3 1 23 - I 135 146 R/W 40
2 R134a 7 R290 12 R728 17 R422A 22 R407F
3 R404A 8 R600 13 R1270 18 R423A 23 R32
4 R407C 9 R600a 14 R417A 19 R407A
5 R410A 10 R717 15 R422D 20 R427A
IS1 S1 probe type 3 1 11 - I 1 249 R/W 40
1 1 to 4.2 barg 7 0 to 45 barg
2 0.4 to 9.3 barg 8 1 to 12.8 barg
3 -1 to 9.3 barg 9 0 to 20.7 barg
4 0 to 17.3 barg 10 1.86 to 43.0 barg
5 0.85 to 34.2 barg 11 reserved
6 0 to 34.5 barg
ICP PID: proportional gain 15 0 800 - A 151 256 R/W 40
Iti PID: integral time 150 0 999 sec I 171 252 R/W 40
IC1 LowSH protection: threshold 5 -9 IP3 °C/°F A 152 257 R/W 40
IC2 LowSH protection: integral time 15 0 800 sec A 153 258 R/W 40
IC3 LOP protection: threshold -50 -121 IC5 °C/°F A 154 259 R/W 40
IC4 LOP protection: integral time 0 0 800 sec A 155 260 R/W 40
IC5 MOP protection: threshold 50 IC3 392 °C/°F A 156 261 R/W 40
IC6 MOP protection: integral time 20 0 800 sec A 157 262 R/W 40
IC7 MOP protection: disable threshold 30 -121 392 °C/°F A 158 263 R/W 40
IC8 Low suction temperature alarm threshold -50 -121 392 °C/°F A 159 264 R/W 40
IIA Enable operating mode modification 0 0 1 - I 2 250 R/W 40
0/1 = enabled/not enabled
IU1 Enable manual valve positioning 0 0 1 - D 182 58 R/W 40
0/1 = enabled/not enabled
IU2 Manual valve position 0 0 999 step I 128 141 R/W 40
IU3 Valve control steps: 1/2 = 480/960 step 1 1 2 - I 195 184 R/W 40
IU4 Valve opening at start (evaporator/valve capacity ratio) 50 0 100 % I 173 254 R/W 40
In1 Serial address 99 1 99 - I 133 144 R/W 40
ICG Enable EVDice regulation 0 0 1 - I 184 60 R/W 39
0/1 = not enabled/ enabled 40

67 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
Par. Description Def Min Max UOM Type CAREL SVP Modbus R/W page
SVP

Ultra 3PH Module commissioning

cH1 3PH module serial address 1 1 247 - I 185 177 R/W 41
42
cH2 3PH module offset serial address 0 0 232 - I 186 178 R/W 41
42
cH3 Type of three phase module 0 0 1 - I 187 179 R/W 41
0 = Evaporator 42
1 = Full
cA1 Sd1 probe connection 0 0 1 - D 130 40 R/W 41
0 = in UltraCella 42
1 = in 3PH module
cA2 Sd2 probe connection 0 0 1 - D 131 41 R/W 41
0 = in UltraCella 42
1 = in 3PH module
cA3 Sc probe connection 0 0 1 - D 132 42 R/W 41
(Full module only) 42
0 = in UltraCella
1 = in 3PH module
cEn Enable 3PH mod. 0 0 1 - D 133 43 R/W 41
0 = disable 42
1 = enable

HACCP alarms (MULTIFUNCTION MENU)

HA Date/time of last HA alarm: day - 1 7 giorno I 72 29 R 69
Date/time of last HA alarm: hour - 1 23 ora I 73 30 R 69
Date/time of last HA alarm:minute - 1 59 min I 74 31 R 69
HA1 Date/time of second last HA alarm: day - 1 7 giorno I 75 32 R 69
Date/time of second last HA alarm: hour - 1 23 ora I 76 33 R 69
Date/time of second last HA alarm:minute - 1 59 min I 77 34 R 69
HA2 Date/time of third last HA alarm: day - 1 7 giorno I 78 35 R 69
Date/time of third last HA alarm: hour - 1 23 ora I 79 36 R 69
Date/time of third last HA alarm:minute - 1 59 min I 80 37 R 69
HAn Number of HA alarms - 1 15 - I 96 53 R 69
HF Date/time of last HF alarm: day - 1 7 giorno I 81 38 R 69
Date/time of last HF alarm: hour - 1 23 ora I 82 39 R 69
Date/time of last HF alarm:minute - 1 59 min I 83 40 R 69
HF1 Date/time of second last HF alarm: day - 1 7 giorno I 86 43 R 69
Date/time of second last HF alarm: hour - 1 23 ora I 87 44 R 69
Date/time of second last HF alarm:minute - 1 59 min I 88 45 R 69
HF2 Date/time of third last HF alarm: day - 1 7 giorno I 91 48 R 69
Date/time of third last HF alarm: hour - 1 23 ora I 92 49 R 69
Date/time of third last HF alarm: minute - 1 59 min I 93 50 R 69
HFn Number of HF alarms - 1 15 - I 97 54 R 69
Hcr Reset HACCP alarms 0 0 1 - D 23 12 R/W 69
Tab. 7.a

Variables accessible ONLY via serial connection

Message on the Description Type Variable type R/W CAREL Modbus
display address Address
rE Virtual probe fault alarm Alarm D R 39 17
E0 Probe 1 fault alarm Alarm D R 40 18
E1 Probe 2 fault alarm Alarm D R 41 19
E2 Probe 3 fault alarm Alarm D R 42 20
E3 Probe 4 fault alarm Alarm D R 43 21
E4 Probe 5 fault alarm Alarm D R 44 22
LO Low temperature alarm Alarm D R 45 23
HI High temperature alarm Alarm D R 46 24
IA Immediate external alarm Alarm D R 47 25
dA Delayed external alarm Alarm D R 48 26
Ed1 Defrost timeout alarm, evaporator 1 Alarm D R 50 28
Ed2 Defrost timeout alarm, evaporator 2 Alarm D R 51 29
Pd Pd alarm active Alarm D R 52 30
LP Low pressure alarm Alarm D R 53 31
Ats Pump Down autostart alarm Alarm D R 54 32
dor Door open for too long alarm Alarm D R 55 33
Etc RTC fault alarm Alarm D R 56 34
EE Control parameter EEPROM alarm Alarm D R 57 35
EF Operating parameter EEPROM alarm Alarm D R 58 36
HA Type HA HACCP alarm Alarm D R 59 37
HF Type HF HACCP alarm Alarm D R 60 38
CHT High condenser temperature alarm Alarm D R 62 40
- Active alarms Alarm D R 63 41
SHA EVD EVO - Low superheat protection Alarm D R 73 42
LOA EVD EVO - LOP protection Alarm D R 75 44
MOA EVD EVO - MOP protection Alarm D R 77 46
EEA EVD EVO - Valve motor fault Alarm D R 79 48
LSA EVD EVO - Low pressure alarm Alarm D R 81 50
Hit EVD EVO - High cond. temperature protection activated Alarm D R 83 52
ES1 EVD EVO - Probe S1 fault Alarm D R 84 53
ES2 EVD EVO - Probe S2 fault Alarm D R 85 54
ES3 EVD EVO - Probe S3 EVO fault Alarm D R 86 55
UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 68
 ENG
ES4 EVD EVO - Probe S4 alarm Alarm D R 87 56
bAt EVD EVO - Battery discharged or faulty Alarm D R 88 57
EEE EVD EVO - Op. and/or parameter EEPROM error Alarm D R 89 58
EIC EVD EVO - Valve not closed completely Alarm D R 90 59
EEC EVD EVO - Valve closed in emergency Alarm D R 91 60
EFU EVD EVO - FW compatibility error (>=5.0) Alarm D R 92 61
ECN EVD EVO - Configuration error Alarm D R 93 62
ELE EVD EVO offline Alarm D R 94 63
dnL Parameter download not successful Alarm D R 115 75
uPd Parameter upload not successful Alarm D R 116 76
EPE 3PH module offline Alarm D R 119 78
EP0 Probe Sd1 fault 3PH module Alarm D R 120 79
EP1 Probe Sd2 fault auxiliary evap. 3PH module Alarm D R 121 80
EP2 Probe Sc fault 3PH module Alarm D R 122 81
EPn 3PH module configuration error Alarm D R 123 82
EPM 3PH module motor protector alarm Alarm D R 124 83
EPU High/low pressure alarm or Kriwan activated 3PH module Alarm D R 125 84
LOG UltraCella software update not successful Alarm D R 143 94
ALM Alarm log download not successful Alarm D R 144 95
SOF UltraCella software update not successful Alarm D R 145 96
IA1 EVD ICE - Probe S1 fault Alarm D R 169 110
IA2 EVD ICE - Probe S2 fault Alarm D R 170 111
IE1 EVD ICE - MOP alarm Alarm D R 171 112
IE2 EVD ICE - LOP alarm Alarm D R 172 113
IE3 EVD ICE - Low superheat alarm Alarm D R 173 114
IE4 EVD ICE - Low pressure alarm Alarm D R 174 115
IE5 EVD ICE - Valve closed in emergency Alarm D R 175 116
IE6 EVD ICE - Control from digital input if offline Alarm D R 176 117
IE7 EVD ICE - Ultracap supplied at low voltage or battery low level Alarm D R 177 118
IE8 EVD ICE - Valve not closed completely Alarm D R 178 119
IEE EVD ICE - Op. and/or parameter EEPROM error Alarm D R 179 120
ILE EVD ICE offline Alarm D R 180 121
IEC EVD ICE – Configuration error Alarm D R 185 123
IEM EVD ICE – Alignment error with UltraCella Alarm D R 186 124
Y1 0 to 10 V analogue output Status A R 6 5
- Virtual probe Status A R 26 6
- Application version Info A R 27 7
- EVD ICE - Probe S1 value Status A R 58 16
- EVD ICE - Probe S2 value Status A R 59 17
- EVD EVO - Probe S1 value Status A R 60 18
- EVD EVO - Probe S2 value Status A R 61 19
ESA EVD EVO - Evaporation temperature Status A R 62 20
- EVD EVO - Superheat value Status A R 63 21
U1 Probe Sd1 value 3PH module Status A R 65 23
U2 Probe Sd2 value 3PH module Status A R 66 24
U3 Probe Sc value 3PH module Status A R 67 25
- 3PH0 to 10 V analogue output Status A R 68 26
- First variable shown on LED display Status A R 72 83
- Second variable shown on LED display Status A R 73 84
- EVD ICE - Valve position % Status A R 143 98
- EVD ICE - Superheat Status A R 144 99
ISu EVD ICE - Suction temperature Status A R 145 100
- EVD ICE - Evaporation pressure Status A R 146 101
ISa EVD ICE - Evaporation temperature Status A R 147 102
b1 Probe 1 value Status A R 160 105
b2 Probe 2 value Status A R 161 106
b3 Probe 3 value Status A R 162 107
b4 Probe 4 value Status A R 163 108
b5 Probe 5 value Status A R 164 109
di1 Digital input 1 status (N.C.) Status D R 2 1
di2 Digital input 2 status Status D R 3 2
di3 Digital input 3 status Status D R 4 3
do1 Compressor relay status Status D R 5 4
do2 Defrost relay status Status D R 6 5
do3 Evaporator fan relay status Status D R 7 6
do4 Light relay status Status D R 8 7
do6 AUX 2 relay status Status D R 9 8
do5 AUX 1 relay status Status D R 10 9
- Controller ON/OFF command Command D R/W 26 15
- Continuous cycle call command Command D R/W 27 16
- Defrost call command Command D R/W 28 17
- LIGHT activation command Command D R/W 29 18
- AUX1 activation command Command D R/W 30 19
- AUX2 activation command Command D R/W 31 20
off OFF Status D R 32 10
cc Continuous cycle Status D R 33 11
def Defrost Status D R 34 12
- Compressor Status D R 38 16
- Alarm reset Command D R/W 64 21
dU4 3PH digital input 1 status Status D R 127 86
dU5 3PH digital input 2 status Status D R 128 87
- EVD ICE - Valve position in steps Status I R 168 62
- EVD EVO - Valve position % Status I R 204 91
- EVD EVO - Valve position in steps Status I R 205 92
Tab. 7.b

69 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
8. SIGNALS AND ALARMS
8.1 Signalling Example: display after alarms rE and E0.
The signals are messages that appear on the display to notify the user
regarding the performance of control procedures (such as defrost) or
confirmation of controls from keyboard.  
1 2 1 2 1 2
Code Description
--- It appears at controller start-up
--- Probe not enabled Note: in order to deactivate the buzzer and the relay alarm press
the Alarm key
Parameters categories
Pro Probes
CtL Control Note: the figures refer to the screens on models with single row
CMP Compressor display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
dEF Defrost the display shows the alarm messages on the second row.
ALM Alarm
Fan Fan Note: the buzzer is disabled during the wizard on the UltraCella
CnF Configuration Service terminal.
HcP HACCP
rtc Clock
doL Door and light
rcP Recipes 8.3 Reset alarms
GEF Generic functions
EVO EVD EVO module Alarms with automatic reset automatically reset when the cause that
ICE EVDice generated them, for example, after the replacement of a faulty probe,
3PH Three phases Module 3PH at the end of the alarm for high temperature, etc. For those with manual
reset it is necessary to first remove the cause that generated them, and
Messages that appear during navigation then press the Alarm button for entire restore.
PAS Password
HA HACCP alarm, HA type
HF HACCP alarm, HF type Example: display and manual restore alarm CHt (condenser high
rES Reset alarms with manual reset temperature)
Reset HACCP alarms
Reset temperature monitoring
cc Continuous cycle 
Ed1 Defrost on evaporator 1 ended by time-out 
Ed2 Defrost on evaporator 2 ended by time-out 1 2 1 2

On Switch ON
OFF Switch OFF
AUX Auxiliary output switch on request
rEc Temperature registration
no Operation not executed
 
uPd Parameters upload
dnL Parameters download 1 2 1 2 1 2

bni Menu parameters set (bn)

r01…r10 Recipe 1…10
MAX Maximum temperature read Note: the figures refer to the screens on models with single row
MIN Minimum temperature read display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
Op Open
the display shows the alarm messages on the second row
cLo Closed
EXT Exit menu
Hcr Reset HACCP alarms
VEr Software release
LOG Temperature recorded download
ALG Alarms recorded download 8.4 HACCP alarms and display
Tab. 8.a In order to activate monitoring see par 8.6
(HACCP = Hazard Analysis and Critical Control Point).
HACCP can only be activated on the controllers with the RTC option fitted,
and allows control of the operating temperature and the recording of any
anomalies due to power failures or increases in the operating temperature
8.2 Alarms due to various causes (breakages, severe operating conditions, operator
errors, etc…). There are two types of HACCP events:
There are two types of alarms: • HA alarms, high temperature during operation;
• system alarms: e.g. Eeprom alarms, communication (interrupted) • HF alarms, high temperature after power black out.
alarms, HACCP, high (HI) and low (LO) temperature alarms, high (AUH) The alarm causes the blinking of HACCP icon, the display of the relative
and low (AUL) humidity; alarm code on the display, storage of the alarm and activation of the
• control alarms: e.g. pump down ended by time-out (Pd), low pressure buzzer.
(LP).
The auxiliary digital outputs AUX1, AUX2 can be configured to signal Example: display after HF error and restore of the alarm condition:
the alarm status, as normally energised or normally de-energised. See
chapter 5. The control indicates the alarms triggered due to faults in
the control itself, in the probes or in the network communication. You can
also activate an alarm from external contact, immediate type. See chapter 
4. On the display the message “IA” appears and at the same time the bell 
icon blinks and the buzzer activates. If more errors occur, they will appear
1 2 1 2
in sequence on the display.

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 70

 ENG
8.5 EVD EVO alarms
If an Ultra EVD module, P/N WM00E%, is connected by Fieldbus, UltraCella
will be able to signal the following alarms, which only depend on the
 status of the EVD EVO controller fitted on the module.

Button flashing

Icon flashing
Alarm code

description

Alarm relay
on display

on display

on display
1 2 1 2

Buzzer
Alarm

Reset
Note: the figures refer to the screens on models with single row
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*,
the display shows the alarm messages on the second row SHA Low superheat protection - ON ON Automatic
LOA LOP protection - ON ON Automatic

Display and cancel HACCP alarms MOA MOP protection - ON ON Automatic

Access the multifunction menu (see chap. 3) and choose HcP. In the EEA Valve motor fault - ON ON Automatic
multifunction menu you can see the date and time of the last 3 alarms HA Threshold and timeout
and HF. After entering the multifunction menu (see previous par.), select LSA - ON ON Automatic
exceeded
with UP / DOWN the message “HCP”. High condensing
Hit temperature protection - ON ON Automatic
Par. Description Def Min Max U.o.M.
activated
HA Date/time of last HA alarm 0 - - - Probe S1 fault or set point
HA1 Date/time of second last HA alarm 0 - - - ES1 - ON ON Automatic
exceeded
HA2 Date/time of third last HA alarm 0 - - - Probe S2 fault or set point
HAn Number of HA alarms 0 0 15 - ES2 - ON ON Automatic
exceeded
HF Date/time of last HF alarm 0 - - - Probe S3 fault or set point
HF1 Date/time of second last HF alarm 0 - - - ES3 - ON ON Automatic
exceeded
HF2 Date/time of third last HF alarm 0 - - -
Probe S4 fault or set point
HFn Number of HF alarms 0 0 15 - ES4 - ON ON Automatic
exceeded
Hcr HACCP alarms cancelling 0 0 1 -
Battery discharged
Action on variation 01 o 10 bAt or faulty or electrical - ON ON Automatic
Procedure: connection interrupted
1. Press Set and then UP/DOWN to display the parameters of the following Operating and/or
EEE - ON ON Automatic
parameter EEPROM error
table; Valve not closed
2. Press Set to display the alarm date and time; EIC - ON ON Automatic
completely
3. Press Prg until you return to standard display. Valve closed in
EEC - ON ON Automatic
4. To cancel all HACCP alarms, change the value of the parameter Hcr emergency
FW compatibility error
Each alarm is displayed with scrolling text, which contains the day of EFu - ON ON Automatic
(>=5.0)
week, hour, minute, and the temperature that caused the alarm. The
ECn Configuration error - ON ON Automatic
buffer in which are saved can contain the data of up to 3 alarms. Once
full, the new alarm will replace the oldest one. Instead, the alarm counters ELE EVD offline - ON ON Automatic
(HAn, HFn), after reaching 15, they stop. Tab. 8.b

Example: HA alarm triggered Thursday at 13:17, with detected 8.6 EVDice alarms
temperature of 36.8 °C.
If an EVDice driver is connected via Fieldbus, UltraCella will be able to
signal the following alarms, which depend solely on the status of the
driver.
Button flashing

Icon flashing
Alarm code

description

Alarm relay
on display

on display

on display


Buzzer
Alarm

Reset

1 2 1 2

IA1 Probe S1 fault - ON ON Automatic

IA2 Probe S2 fault - ON ON Automatic
IE1 MOP protection - ON ON Automatic
 
IE2 LOP protection - ON ON Automatic
IE3 Low superheat protection - ON ON Automatic
1 2 1 2
IE4 Low suction temperature
- ON ON Automatic
alarm
IE5 Valve emergency closing
- ON ON Automatic
(Ultracap)
IE6 Regulation by digital input in
- ON ON Automatic
  case of offline
IE7 Ultracap module powered
with low voltage or low - ON ON Automatic
1 2 1 2 charge level
IE8 Emergency closure is not
- ON ON Automatic
     completed
IEE Operating and/or parameter
- ON ON Automatic
Note: the figure refers to the screens on models with single row EEPROM error
display, P/Ns WB000S*. In models with two rows, P/Ns WB000D*, ILE EVD ICE offline - ON ON Automatic
as well as the message indicated, during navigation the display shows the IEC Configuration error - ON ON Automatic
scrolling message “HACCP Alarms” on the second row.
IEM Alignment error with
- ON ON Manual
UltraCella
Tab. 8.c
71 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
8.7 3PH module alarms

Icon flashing on
Button flashing
Alarm code on

Alarm cause

Alarm relay
on display
display

display

Buzzer

Reset
EPE 3PH Module off -line - ON ON Automatic
Sd1 probe fault (3PH
EP0 - ON ON Automatic
module)
Sd2 probe fault (3PH
EP1 - ON ON Automatic
module)
Sc probe fault (3PH
EP2 - ON ON Automatic
module)
3PH module
EPn - ON ON Automatic
configuration fault
Motor protector alarm
EPM - ON ON Manual
(3PH module)
High/low pressure
EPU or Kriwan alarm (3PH - ON ON Manual
module)
Tab. 8.d

ALARM TABLE

Continuous cycle
display flashing

Condenser fans
Cod. display

Alarm cause

Compressor
Icon on the

Display key

Alarm relay

Evaporator
PD valve
flashing

Defrost
Buzzer

Reset

Fans
rE Virtual control probe fault ON ON automatic duty setting(c4) duty setting(c4) - - - OFF
E0 Probe B1 fault ON ON automatic duty setting(c4) duty setting(c4) - - - OFF
E1 Probe B2 fault ON ON automatic - - - - - OFF
E2 Probe B3 fault ON ON automatic - - - - - -
E3 Probe B4 fault ON ON automatic - - - - - -
E4 Probe B5 fault ON ON automatic
LO Low temperature alarm - ON ON automatic - - - - - -
HI High temperature alarm - ON ON automatic - - - - - -
IA Immediate alarm from external contact - ON ON automatic duty setting (A6) duty setting(A6) OFF - - OFF
Pd Maximum pump down time alarm - ON ON automatic - - - - - -
LP Low pressure alarm - ON ON automatic OFF OFF OFF - - -
AtS Autostart in pump down - ON ON autom./man - - - - - -
CHt High condenser temperature alarm - ON ON manual OFF OFF - - OFF -
dor Door open too long alarm - ON ON automatic - - - - - -
Etc Real time clock is broken ON ON automatic - - - - - -
EE EEprom error, unit parameters ON ON automatic - - - - - -
EF Eeprom error, operating parameters ON ON automatic - - - - - -
Ed1, ON ON automatic
Defrost ended by timeout -
Ed2
HA HACCP alarm, HA type - ON ON manual - - - - - -
HF ON ON manual - - - - - -
HACCP alarm, HF type - +

LoG Download recorded temperature fault - OFF ON automatic - - - - - -

uPL Parameters upload fault - OFF ON automatic - - - - - -
dnL Parameters download fault - OFF ON automatic - - - - - -
SOF Software update fault - OFF ON automatic - - - - - -
SHA EVD EVO - Low superheat protection - ON ON automatic OFF OFF OFF - - -
LOA EVD EVO - LOP protection - ON ON automatic OFF OFF OFF - - -
MOA EVD EVO - MOP protection - ON ON automatic OFF OFF OFF - - -
EEA EVD EVO - Valve motor fault - ON ON automatic OFF OFF OFF - - -
LSA EVD EVO - Threshold and timeout exceeded - ON ON automatic - - - - - -
Hit EVD EVO - High condensing temperature protection activated - ON ON automatic - - - - - -
ES1 EVD EVO - Probe S1 fault or set point exceeded - ON ON automatic OFF OFF OFF - - -
ES2 EVD EVO - Probe S2 fault or set point exceeded - ON ON automatic OFF OFF OFF - - -
ES3 EVD EVO - Probe S3 fault or set point exceeded - ON ON automatic - - - - - -
ES4 EVD EVO - Probe S4 fault or set point exceeded - ON ON automatic - - - - - -
EVD EVO - Battery discharged or faulty or electrical connection ON ON automatic - - - - - -
bAt -
interrupted
EEE EVD EVO - Operating and/or parameter EEPROM error - ON ON automatic OFF OFF OFF - - -
EIC EVD EVO - Valve not closed completely - ON ON automatic - - - - - -
EEC EVD EVO - Valve closed in emergency - ON ON automatic OFF OFF OFF - - -
EFu EVD EVO - FW compatibility error (>=5.0) - ON ON automatic - - - - - -
ECn EVD EVO - Configuration error - ON ON automatic - - - - - -
ELE EVD EVO - EVD offline - ON ON automatic OFF OFF OFF - - -
ALM Download log allarmi non riuscito - OFF ON automatic - - - - - -
EPE Off-line 3PH module - ON ON automatic OFF OFF OFF OFF - -
ON ON automatic - - End - - -
by
EP0 Sd1 probe fault (3PH module) - time
if Sd1
only
UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 72
 ENG
EP1 Sd2 probe fault (3PH module) - ON ON automatic - - - - - -
EP2 Sc probe fault (3PH module) - ON ON automatic - - - - - -
EPn 3PH module configuration fault - ON ON automatic OFF OFF OFF OFF - -
EPM Motor protector alarm (3PH module) - ON ON manual OFF OFF OFF OFF OFF -
EPU High/low pressure or Kriwan alarm (3PH module) - ON ON manual OFF OFF OFF OFF OFF -
AUH High humidity alarm - ON ON automatic - - - - - -
AUL Low humidity alarm - ON ON automatic - - - - - -
GH1 High generic alarm (stage 1 ON/OFF – generic function) - ON ON automatic - - - - - -
GL1 Low generic alarm (stage 1 ON/OFF – generic function) - ON ON automatic - - - - - -
GH2 High generic alarm (stage 2 ON/OFF – generic function) - ON ON automatic - - - - - -
GL2 Low generic alarm (stage 2 ON/OFF – generic function) - ON ON automatic - - - - - -
GH3 High generic alarm (modulating output – generic function) - ON ON automatic - - - - - -
GL3 Low generic alarm (modulating output – generic function) - ON ON automatic - - - - - -
GA1 Generic alarm (alarm 1 – generic function) - ON ON automatic - - - - - -
GA2 Generic alarm (alarm 2 – generic function) - ON ON automatic - - - - - -
IA1 EVD ICE – Probe S1 fault - ON ON automatic OFF OFF OFF - - -
IA2 EVD ICE – Probe S2 fault - ON ON automatic OFF OFF OFF - - -
IE1 EVD ICE – MOP protection - ON ON automatic OFF OFF OFF - - -
IE2 EVD ICE – LOP protection - ON ON automatic OFF OFF OFF - - -
IE3 EVD ICE – Low superheat protection - ON ON automatic OFF OFF OFF - - -
IE4 EVD ICE – low suction temperature alarm - ON ON automatic - - - - - -
IE5 EVD ICE – valve in emergency closing (Ultracap) - ON ON automatic OFF OFF OFF - - -
IE6 EVD ICE – control from dig. input if offline - ON ON automatic OFF OFF OFF - - -
IE7 EVD ICE – Ultracap module powered with low voltage or low - ON ON automatic - - - - - -
charge level
IE8 EVD ICE – incomplete valve closing - ON ON automatic OFF OFF OFF - - -
IEE EVD ICE – operating and/or parameter EEPROM error - ON ON automatic OFF OFF OFF - - -
ILE EVD ICE – EVDICE offline - ON ON automatic OFF OFF OFF - - -
IEC EVD ICE – Configuration error - ON ON automatic OFF OFF - - - OFF
IEM EVD ICE – Alignment error with UltraCella - ON ON manual - - - - - -
Tab. 8.e

8.8 Alarm parameters Key

High and low temperature alarm and activation parameters LO Low temperature alarm
AL (AH) allows you to determine the activation temperature for low (high) HI High temperature alarm
temperature alarm LO (HI). The set value AL (AH) is always compared with SV Adjustment probe
the value detected by the control probe. The parameter Ad represents
the alarm activation delay in minutes; the low temperature alarm (LO) Notes:
activates only if the temperature is lower than threshold AL for period
of time greater than Ad. The thresholds can be relative or absolute, • The alarm LO and HI are alarms with automatic reset. A0 determines
depending on the value of parameter A1. In the first case (A1=0) the the hysteresis between the value of the activation and deactivation
value AL indicates the deviation regarding the set point and the low of the alarm;
temperature alarm activation point is: set point - AL. If the set point • if you press the Alarm button when the measurement is above a
differs, the activation point will automatically differ. In the second case threshold, the buzzer and the alarm relay immediately turn off, and
(A1=1), the value AL indicates the low temperature alarm threshold. An an indication of the alarm code will remain active until the measure
active low temperature alarm is indicated via internal buzzer, with the falls within the activation threshold. Parameter A6 has similar meaning
code LO on display and with the activation of the alarm relay. The same as parameter c4 (duty setting). If an external alarm occurs, the
occurs for high temperature alarm (HI), considering AH instead of AL. compressor works for a time equal to the value set for parameter A6,
while it remains OFF for a fixed period of 15 minutes.
Par Description Def Min Max UM • In case of relative alarms (A1= 0) both AL and AH are considered as
A0 Alarm and fan differential 2.0 0.1 20.0 °C/°F absolute values (e.g. AL= -10 is considered as AL= 10)
A1 Alarms threshold (AL, AH) relative to set 0 0 1 -
point or absolute High and low humidity alarms parameters
0/1=relative/absolute If either input B4 or B5 is configured for a humidity probe (On), high
AL Low temperature alarm threshold 0 -50.0 200 °C/°F (AUH) and low humidity alarms (AUL) can also be enabled, with absolute
If A1= 0, AL=0: alarm disabled thresholds (UHL and ULL). The alarms are activated in the following
If A1= 1, AL=-50: alarm disabled conditions:
AH High temperature alarm threshold 0 -50.0 200 °C/°F
• If Su >= UHL --> high umidity alarm AUH
If A1= 0, AL=0: alarm disabled
If A1= 1, AL=200: alarm disabled
• If Su <= ULL --> low umidity alarm AUL
Ad Delay time for low temperature and 120 0 250 min
high temperature alarms Par Description Def Min Max UM
A6 Stop compressor from external alarm 0 0 100 min ULL Absolute low umidity alarm threshold 0 0 100.0 %rH
0 = compressor always off; 0=alarm disabled
100 = compressor always on; UHL Absolute high umidity alarm threshold 100.0 0 100.0 %rH
100=alarm disabled
AdH Humidity alarms AUH, AUL delay 120 0 250 min
A1=1
LO HI
ON

ALARM
OFF

A0 A0 Sv
AL AH
Fig. 8.a
73 UltraCella +0300083EN - rel. 1.7 - 07.01.2016
ENG
8.9 HACCP Alarm parameters and
monitoring activation AH

In order to activate HACCP alarm monitoring, set parameter HCE=1. Sv

St
HA alarms
The HA alarm is generated if during normal operation it is noted that the
temperature read by the control probe exceeds the high temperature t
threshold for the time Ad + Htd. Therefore compared to the normal high ON
ALARM
temperature alarm already signalled by the control, HACCP alarm type HA OFF
is delayed by a further Htd time specific for HACCP recording.
Par. Description Def Min Max U.o.M. t
black out
HCE Enabling HACCP 0 0 1 -
0/1=No/Yes Fig. 8.c
Htd HACCP alarm delay 0 0 250 min Key
Sv Virtual probe
AH High temperature alarm threshold
AH ALARM HACCP alarm, HF type
St Set point
Sv
t Time
St

t
ON
ALARM
OFF

t
8.10 High condenser temperature alarm
Ad Htc
You can monitor the temperature of the condenser to signal the high
Fig. 8.b temperature, probably due to situations of clogging. The signalling
Key follows the figure below.
Sv Virtual probe Par Description Def Min Max UM
St Set point Ac High condenser temperature alarm 70 -50,0 200 °C/°F
t Time threshold
AH High temperature alarm threshold Acd High condenser temperature alarm 0 0 250 min
ALARM HACCP alarm, HA type delay
Ad Delay time for low temperature and high temperature alarms
Htd HACCP alarm delay (0=monitoring disabled)
Ac+10

Sc
Ac
HF alarms
The HACCP alarm type HF is generated as a result of a power failure for a
long time (> 1 minute), when after mains voltage restore the temperature
t
read by the adjustment probe exceeds the high temperature threshold ON
AH . CHT
OFF

t
Acd

Fig. 8.d
Key
t Time
Acd High condenser temperature alarm delay
Sc Condenser probe
Ac High condenser temperature alarm threshold
CHT High condenser temperature alarm

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 74

 ENG
9. TECHNICAL SPECIFICATIONS
9.1 UltraCella technical characteristics
Power Supply Model 230V: Voltage 230 V~ (+10/-15%), 50/60 Hz; Power 18 VA, 100 mA~ max.
Model 24V: Voltage 24 V~ (+10/-15%), 50/60 Hz; Power 18 VA, 1A~ max.
Insulation ensured Insulation for low voltage: reinforced, 6 mm in air, 8 mm superficial, 3750 V.
by 230V power supply Insulation for relay outputs: reinforced, 3 mm in air, 4 mm superficial, 1250 V.
Analog inputs B1, B2, B3: NTC, PT1000 (+-3%)
B4: NTC, 0...10Vdc (+-3%)
B5: 0...5Vdc ratiometric (+-3%) , 4...20mA (+-3%)
Analog output Y1: 0...10 Vdc (10mA max,+-5%)
Note: When installing, keep the supply and loads connections away from the cables of the probes, digital inputs, and monitoring device.
Probe Type NTC std. CAREL: 10 kΩ at 25°C, range from -50°C to 90°C;
measuring error: 1°C in range from -50°C to +50°C; 3°C in range from +50°C to +90°C
NTC HT: 50 kΩ at 25°C, range from 0°C to 150°C;
measuring error: 1.5°C in range from 0°C to +115°C; 4°C in range from +115°C to +150°C
PT1000 std. CAREL: 1000 Ω at 0°C, range from –50°C to +90°C;
measuring error 3°C in range from –50°C to 0°C; 5°C in range from 0°C to +90°C
Probe power supply +Vdc 12 V+-30%, 25 mA max; 5VREF: 5V+-2%
Relay output Applicable ratings based on the relay type
Type of Relay EN60730 -1 (250 V ~) UL 873 (250 V ~)
8A (AUX1, AUX2) 8 (4)A on N.O.; 6 (4)A on N.C.; 2 (2)A on N.C. and N.O. (100000 8A resistive 2FLA 12LRA, C300 (30000 cycles)
cycles)
16A,(LIGHT, FAN) 10A resistive, 5 (3)A (100000 cycles) 10A resistive, 5FLA 18LRA (30000 cycles)
30A(COMP, DEF) 12 (10)A (100000 cycles) 12A resistive, 2HP, 12FLA 72LRA (30000 cycles)
NOTE: The sum of the loads currents COMP, DEF, FAN accessed at the same time should not exceed 20A
Insulation for low voltage: reinforced, 6 mm in air, 8 superficial, 3750 V.
Insulation between independent relay outputs: reinforced, 3 mm in air, 4 superficial, 1250 V.
Connections Section of conductors for analog inputs and outputs, digital inputs, serial: from 0.5 to 2.5mm2 (from 20 to 13 AWG);
Section of supply and loads cables: from 1.5 to 2.5 mm2 (from 15 to 13 AWG)
Serial connections:use shielded cables
Maximum length of the cables: 10 m
Container Plastic: sizes 200 x 100 X 190 mm
Assembly On wall (with plastic container): using fastening screws for front board
Display LED display: 3 and 4 digits, display from -99 to 999; operating status indicated by LEDs and icons formed on the polycarbonate
applied to the plastic
Keyboard 10 keys on keyboard in polycarbonate membrane applied to the plastic
Clock with buffer battery Available depending on the model
Buzzer Available on all models.
Clock Depending on the model installed.
Accuracy: ±100 ppm
Battery: “button” type with lithium code CR2430 voltage: 3Vdc (sizes 24x3 mm)
Serial 3 types of available serials: pLAN, BMS, Fieldbus
PLAN : Driver HW RS485, telephone jack (available only on few models) and screw terminals
BMS Driver HW RS485, screw terminals
Fieldbus: Driver HW RS485, screw terminals
USB Type: Host (A connector); 5Vdc supply, maximum absorption: 100mA (low power devices)

Operating conditions Only board: -10T65°C; <90% U.R. non condensing

With plastic container: -10T50°C, <90% U.R. non condensing
Relay identification, type and maximum resistive current to operating temperature:
Relay Associated load Type of Relay Max resistive current applicable
R1 (AUX2) 8A 8A
R2 (AUX1) 8A 8A
R3 (LIGHT) 16A 10A
R4 (FAN) 16A 10A
R5 (DEF) 30A 12A
R6 (COMP) 30A 12A
NOTE: The sum of the loads currents COMP, DEF, FAN accessed at the same time should not
exceed 20A.
Storage conditions -20T70°C, < 90% U.R. non condensing
Front protection rating With plastic container: IP65
Environmental pollution 2, normal situation
PTI of the isolating materials Printed circuits 250, plastic and insulation materials 175
Resistance to fire class: Category D
Protection against overcharging class Category II, without PE terminal
Category I, with PE terminal
Type of action and disconnection Relay contact 1 B (micro-disconnection)
Control system manufacture Incorporated, electronic control device
Classification according to protection against electric shock Class II by means of appropriate incorporation
Device intended to be hand-held or built into equipment No
designed to be hand held
Class and structure of the software Class A
Control front cleaning Only use neutral detergents and water
Tab. 9.a

75 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
9.2 EVD Modules technical characteristics
Power supply voltage: 230 V~ (+10/-15%), 50/60 Hz; power: 4,5kW max.
NOTE: The maximum simultaneous current draw by all the loads connected to the controller and the
expansion modules must not exceed 20 A.
Classification according to protection against Class II
electric shock
Case plastic, dimensions 128x290x110 mm
Front protection rating with plastic case IP65
Fire resistance category category D
Cleaning the module front panel only use neutral detergents and water
Operating conditions -10T40°C, <90% r.H. non condensing
Storage conditions -20T60°C, <90% r.H. non condensing
PTI of insulating materials printed circuits 250, plastic and insulating materials 175
Tab. 9.b

9.3 Power Modules technical characteristics

Power supply voltage: 230 V~ (+10/-15%), 50/60 Hz; power: 4,5kW max.
NOTE: The maximum simultaneous current draw by all the loads connected to the controller and
the expansion modules must not exceed 20 A
Residual current circuit breaker In=20 A @30 °C, Id=300 mA
Power relay Rating: 30 A resistive, 240 Vac; 3HP 240 Vac
Classification according to protection against electric shock Class II
Case plastic, dimensions 128x290x110 mm
Front protection rating with plastic case IP65
Fire resistance category Category D
Cleaning the module front panel only use neutral detergents and water
Operating conditions -10T40°C, <90% r.H. non condensing
Storage conditions -20T60°C, <90% r.H. non condensing
Tab. 9.c

9.4 3PH EVAPORATOR Modules technical characteristics

Power supply voltage: 400V~(+10/-15%), 50/60Hz, 3PH+N+T, Imax 25A
Classification according to protection against electric shock Class I
Case plastic, dimensions 452x380x186 mm
Weight 8,7 Kg
Front protection rating with plastic case IP65
Cleaning the module front panel only use neutral detergents and water
Operating conditions -10T40°C, <90% r.H. non condensing
Storage conditions -20T60°C, <90% r.H. non condensing
Materials frontal cover in polycarbonate, retro box in technopolymer
Tab. 9.d

9.4.1 Electrical characteristics

Ultra 3PH Evaporator module 6kW Ultra 3PH Evaporator module 9kW
Code WT00E60N00 WT00E90N00
General
Main switch / general protection 4 poles magnetothermic 16A 6kA D 4 poles magnetothermic 25A 6KA D
Loads power supply 400V~(±10%), 50/60Hz, 3PH+N+T 400V~(±10%), 50/60Hz, 3PH+N+T
Insulating transformer PRI 230 Vac PRI 230 Vac
SEC1 230 Vac 40VA SEC1 230 Vac 40VA
SEC2 24 Vac 35VA SEC2 24 Vac 35VA
Protection SEC by fuses Protection SEC by fuses
Status and alarm indication By UltraCella By UltraCella
Input
Main defrost probe NTC 10kΩ NTC 10kΩ
Auxiliary evap. defrost probe NTC 10kΩ NTC 10kΩ
Clicson evaporator Present Present
Thermostat evaporator Present Present
Output
Condensing unit enabling / Solenoid valve 8A (AC1) / 2A (AC23) 1PH 8A (AC1) / 2A (AC23) 1PH
Defrost heaters 6kW, 9A (AC1) 3PH 9kW, 13A (AC1) 3PH
Evaporator fans 0,55kW, 1,5A* (AC23) 3PH 2kW, 5,7A* (AC23) 3PH
0…10Vdc 0…10Vdc
AUX1 output 16A (AC1) 1PH 16A (AC1) 1PH
Tab. 9.e
* Rating with cosφ=0,5;
With different power factor, to calculate the rating consider the formula: I = P / (400 * √3 * cosφ) where P is the power in W

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 76

 ENG
9.5 3PH FULL Modules technical characteristics
Power supply voltage: 400V~(+10/-15%), 50/60Hz, 3PH+N+T, Imax 25A
Classification according to protection against electric shock Class I
Case plastic, dimensions 452x380x186 mm
Weight 9,8 Kg
Front protection rating with plastic case IP65
Cleaning the module front panel only use neutral detergents and water
Operating conditions -10T40°C, <90% r.H. non condensing
Storage conditions -20T60°C, <90% r.H. non condensing
Materials frontal cover in polycarbonate, retro box in technopolymer
Tab. 9.f

9.5.1 Electrical characteristics

Ultra 3PH Full module 4HP Ultra 3PH Full module 7.5HP
Code WT00F4B0N0 WT00F7C0N0
General
Main switch / general protection 4 poles magnetothermic 16A 6kA D 4 poles magnetothermic 25A 6KA D
Loads power supply 400V~ (±10%), 50/60Hz, 3PH+N+T 400V~ (±10%), 50/60Hz, 3PH+N+T
Insulating transformer PRI 230 Vac PRI 230 Vac
SEC1 230 Vac 40VA SEC1 230 Vac 40VA
SEC2 24 Vac 35VA SEC2 24 Vac 35VA
Protection SEC by fuses Protection SEC by fuses
Status and alarm indication By UltraCella By UltraCella
Regulation range of compressor current rating 10…16A (AC3) 3PH 16…20A (AC3) 3PH
Input
Main defrost probe NTC 10kΩ NTC 10kΩ
Auxiliary evap. defrost probe NTC 10kΩ NTC 10kΩ
Condensing probe NTC 10kΩ NTC 10kΩ
Partial condenser Present Present
Pump down Present Present
High/Low pressure Present Present
Kriwan compressor Present Present
Clicson evaporator Present Present
Thermostat evaporator Present Present
Output
Compressor 10...16A (AC3) 3PH 16...20A (AC3) 3PH
Oil compressor heater (Carter) 100W, 0,5A (AC1) 1PH 100W, 0,5A (AC1) 1PH
Condensing fans 0,8kW, 4A (AC15) 1PH 0,8kW, 4A (AC15) 1PH
Defrost heaters 6kW, 9A (AC1) 3PH 9kW, 13A (AC1) 3PH
Evaporator fans 0,55kW, 1,5A* (AC23) 3PH 2kW, 5,7A* (AC23) 3PH
0…10Vdc 0…10Vdc
AUX1 output 16A (AC1) 1PH 16A (AC1) 1PH
Solenoid valve Present Present
Tab. 9.g
* Rating with cosφ=0,5;
With different power factor, to calculate the rating consider the formula: I = P / (400 * √3 * cosφ) where P is the power in W

77 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

 POWER SUPPLY 3P+N+T 400V 50/60HZ
L1
I d

1 2 1
4/A1
L2
I d

3 4
L3
I d

5 6
10. ELECTRICAL WIRING 3PH MODULES

4
N 4/B1
I d

7 8
QF1
PER UNA CORRETTA INSTALLAZIONE
ELETTRICA SI RACCOMANDA
XP1
DI INSTALLARE A MONTE
DEL SEZIONATORE PRESENTE
PE

SUL QUADRO, UNA PROTEZIONE

MAGNETOTERMICA DIFFERENZIALE
FOR THE RIGHT INSTALLATION
IS RECOMMENDED A DIFFERENTIAL
BREAKER SWITCH MOUNTED
UPSTREAM THE GENERAL ISOLATOR

Fig. 10.a
OF THIS PANEL

78
10.1 Electrical wiring 3PH EVAPORATOR Module

5
KM1 KM2
5/D4 5/D3

6
2

2
4

4
BROWN

BROWN
WHITE

WHITE
CYAN

CYAN
GRAY

GRAY

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016

XP1 XP1

6
2

8
4
MACHINE LIMIT

W
U

V
10.1.1 Power circuit
MV1 M RR1
EVAPORATOR FANS DEFROST HEATERS
ENG
 ENG
10.1.2 Power circuit

3/A8
3/B8
MACHINE LIMIT

1
WHITE
CYAN
QF2
2 1

N2 N1

WHITE

CYAN

TC1

RED 0(O1) FU1

40VA

RED 230(O1) FU2 0(I)

RED 0(O2) FU3 230

RED 24(O2) FU4

35VA
15

16

PE
14
13
5/E1

5/D1

XA1

PE1
7/C1

7/C1

Fig. 10.b

79 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

 Ultra 3PH I/O module
J10 J11 J12
J10/NO1 J10/C1/2 J10/NO2 J11/NO3 J11/C3/4/5 J11/NO4 J11/C3/4/5 J11/NO5 J12/NO6 J12/NC6 J12/C6

80
12
14

12
14
KR3 KR2
5/D5 5/D7

ORANGE 11

ORANGE 11
ORANGE

ORANGE
A1

A1

A1

A1
XA1 XA1 XA1 XA1
KM2 KM1 KR3 KR2

110
149

109
148
A2

A2

A2

A2
16

2
RED
4/D8
15 RED AUX2 AUX1
4/E8
CONSENT MAX 16A AC1
UNIT

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016

Fig. 10.c
XA1 XA1 XA1 XA1 XA1 CONDENSING

119
117

118

129
120

128
MACHINE LIMIT
10.1.3 Auxiliary circuit

TS1 SP3
P

N
L
AP3
SECURITY THERMOSTAT EVAPORATOR CLICSON ULTRACELLA
ENG
ENG

UltraCella +0300083EN - rel. 1.7 - 07.01.2016

Ultra 3PH I/O module
J2
J2/U1 J2/U2 J2/U3 J2/GND J2/U4 J2/U5 J2/U6 J2/GND J2/U7 J2/U8 J2/U9 J2/U10 J2/GND

81
RED

RED

RED

RED

Fig. 10.d
XA1 XA1 XA1 XA1 XA1 XA1
141

146
140

142

143

147
10.1.4 Auxiliary circuit

MACHINE LIMIT
ST1 ST2

GND
TS2
DEFROST DEFROST AUX FANS EVAPORATORE 0-10VDC
 Ultra 3PH I/O module
AP1
J1 J6 J9
J1/G J1/G0 J1/VBAT J6/- J6/+ J6/GND J9/+5VREF J9/GND J11/+VDC
RED

RED

4/D8

82
13
4/D8 BELDEN

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016

Fig. 10.e
XA1

161
160

162
MACHINE LIMIT
10.1.5 Auxiliary circuit

+
-

GND
AP
485 ULTRACELLA
ENG
 ENG
10.1.6 Connectionforoperationwithpowertosolenoidvalve
If the solenoid valve requires power, the 230 Vac power supply available at
terminals 128-129 can be used, as shown in the following wiring diagram:

128

129

148

149
N
L

liquid valve

83 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

 XP1

XA1
ENG
5 5
Evaporator fans MV1:U 1 KM1:2
6 6

Terminals
M
Evaporator fans MV1:V 2 KM1:4
7 7
Evaporator fans MV1:W 3 KM1:6
4

8
7
6
5
3
2
1
4 QF1:8/QF2:N1

PE

PE3
PE2
PE1
162
161
160
149
148
147
146
143
142
141
140
129
128
120
119
118
117
110
109
8 8
Defrost heaters RR1 5 KM2:2
9 9
Defrost heaters RR1 6 KM2:4
10 10
Defrost heaters RR1 7 KM2:6
4 4

RS485 -
RS485 +
Defrost heaters RR1 8 QF1:8
10.1.7 Terminal units

AUX1 relay

RS485 GND
PE

Defrost heaters
Evaporator fans

Ground terminal

Ground terminals
Number and description

Defrost probe NTC

Fig. 10.f

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016

Clicson evaporator fans
XP1

Safe thermostat evaporator fans

0…10V for evaporator fans (GND)

Defrost probe NTC aux evaporator
0…10V for evaporator fans (signal)
Power supply 230Vac for UltraCella
terminal block

Condensing unit enabling / Solenoid valve

27 27
AUX 1 AUX1:1 109 KR2:11
26 26
AUX 1 AUX1:2 110 KR2:14
18 18

-
-
-
-
-
-
-
-
-
-
Safe thermostat TS1 117 ??:J10/NO1
20 20
Safe thermostat TS1 118 KM2:A1

84
Notes
19 19
Evaporator fans clicson SP3 119 ??:J10/NO2
22 22

UltraCella
UltraCella
Evaporator fans clicson SP3 120 KM1:A1
16 16
UltraCella AP3:L 128 FU2:2/??:J12/NC6
15 15
UltraCella AP3:N 129 KR1:A2/KR2:A2
28 28
defrost ST1 140 ??:J2/U1

To supply UltraCella
29 29
defrost ST1 141 XA1:143
30 30
defrost aux ST2 142 ??:J2/U2
29 29
defrost aux ST2 143 XA1:141/??:J2/GND
31 31
Evaporator fans 0...10Vdc Y TS2:Y 146 ??:J2/U6
29 29
Evaporator fans 0...10Vdc GND TS2:GND 147 ??:J2/GND

Fieldbus - connection to UltraCella

25 25
Condensing unit enabling AUX2:1 148 KR1:11
24 24
Condensing unit enabling AUX2:2 149 KR1:14
32 32
Control - AP1:J6/- 160 AP:-
33 33
Control + AP1:J6/+ 161 AP:+
34 34
Control GND AP1:J6/GND 162 AP:GND
17
PE1 TC1:PE
PE2
PE3
XA1

Normally closed. If active (open), evaporator fans are off and it’s not notified in

Normally closed. If active (open), evaporator fans are off and it’s not notified in
terminal block

Tab. 10.a
ENG

UltraCella +0300083EN - rel. 1.7 - 07.01.2016

POWER SUPPLY 3P+N+T 400V 50/60HZ
L1 WHITE
I d

1 2 1
4/A1
L2 GRIGIO
I d

3 4
L3 BROWN
I d

5 6
N CYAN 4
4/B1
I d

7 8
QF1
PER UNA CORRETTA INSTALLAZIONE
ELETTRICA SI RACCOMANDA
XP1
DI INSTALLARE A MONTE
1

5
DEL SEZIONATORE PRESENTE
PE

QM1
SUL QUADRO, UNA PROTEZIONE
MAGNETOTERMICA DIFFERENZIALE
I > I > I >
FOR THE RIGHT INSTALLATION

6
2

4
IS RECOMMENDED A DIFFERENTIAL

85
BREAKER SWITCH MOUNTED

BROWN
WHITE
UPSTREAM THE GENERAL ISOLATOR

GRAY
OF THIS PANEL

5
KM3 KM1 KM2
5/D5 5/D4 5/D3
10.2 Electrical wiring 3PH FULL Module

6
2

2
4

4
BROWN

BROWN

BROWN
WHITE

WHITE

WHITE
CYAN

CYAN
GRAY

GRAY

GRAY

Fig. 10.g
XP1 XP1 XP1

1
11
9

6
2

8
10

4
MACHINE LIMIT
10.2.1 Power circuit

W
U

V
W
U

V
MV1 M RR1
MV2 M
COMPRESSOR EVAPORATOR FANS DEFROST HEATERS
 1 WHITE
3/A8
4 CYAN
3/B8
N1
1

QF2

230
0(I)
TC1
40VA 35VA
CYAN
WHITE

PE
2

N2

FU1

FU2

FU3

FU4
XA1

PE1

PE2

PE3
230(O1)

24(O2)
0(O1)

0(O2)

86
13

61
KM3 KM3

RED

RED

RED

RED
5/D5 5/D5
23

14

62
7/C1
22
7/C1
25
5/D1
24
5/E1
XA1 XA1 XA1 XA1 XA1

101

106
102

103

105

107

108
104
MACHINE LIMIT

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016

Fig. 10.h
1 2 PE 1 2 PE
RR2
SP1
MV3 M P MV4 M
1 1 CRANKCASE HEATER
10.2.2 Power circuit

(Carter)
CONDENSER FANS 1 CONDENSER FANS 2
PARTIALIZATION PRESSURE SWITCH CONDENSER FAN
800W MAX
ENG
ENG

UltraCella +0300083EN - rel. 1.7 - 07.01.2016

Ultra 3PH I/O module
J10 J11 J12
J10/NO1 J10/C1/2 J10/NO2 J11/NO3 J11/C3/4/5 J11/NO4 J11/C3/4/5 J11/NO5 J12/NO6 J12/NC6 J12/C6

87
12
14
KR2
5/D7

11
ORANGE

ORANGE
A1

A1

A1

A1

A1
XA1 XA1
KR1 KM2 KM1 KM3 KR2

110
109
A2

A2

A2

A2

A2
25 RED

2
4/D8
24 RED AUX1
4/E8
MAX 16A AC1

Fig. 10.i
XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1
10.2.3 Auxiliary circuit

111

121
116

119
112
113

115

117

118
114

126

129
120

122

123

125

127

128
124
MACHINE LIMIT
YV1

N
11
12
14
L
SP2 TS1 SP3
P P

N
L
AP2 VEDI PG.9
AP3
TK1
LIQUID VALVE ULTRACELLA
KRIWAN PRESSURE SWITCH SECURITY THERMOSTAT EVAPORATOR CLICSON PUMP DOWN
 Ultra 3PH I/O module
J2
J2/U1 J2/U2 J2/U3 J2/GND J2/U4 J2/U5 J2/U6 J2/GND J2/U7 J2/U8 J2/U9 J2/U10 J2/GND
RED

RED
13

12
14

QM1 KR1
3/B4 5/D2
11
14

88
RED

RED

RED

RED

RED

RED

RED

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016

Fig. 10.j
XA1 XA1 XA1 XA1 XA1 XA1 XA1 XA1
141

146
140

142

143

145

147
144
MACHINE LIMIT
10.2.4 Auxiliary circuit

ST1 ST2 ST3

GND
TS2
DEFROST PROBE DEFROST AUX PROBE CONDENSER PROBE EVAPORATOR FANS 0...10VDC
ENG
ENG

UltraCella +0300083EN - rel. 1.7 - 07.01.2016

Ultra 3PH I/O module
J1 J6 J9
J1/G J1/G0 J1/VBAT J6/- J6/+ J6/GND J9/+5VREF J9/GND J11/+VDC
RED

RED

23
4/D8
22
4/D8 BELDEN

89
Fig. 10.k
XA1

161
160

162
MACHINE LIMIT
10.2.5 Auxiliary circuit

+
-

GND
AP
RS485 FIELDBUS TO ULTRACELLA
ENG
10.2.6 Connection for Pump Down or thermostat Connections for pump down controlled by pressure, with
working simultaneous activation of the compressor and solenoid valve
Connections for pump down controlled by pressure, with If the pump down procedure needs to be performed, controlled by
pressure via a pressure switch connected to the Ultra 3PH Full three-
compressor shutdown due to low pressure
phase module rather than UltraCella, with simultaneous actvation and
If the pump down procedure needs to be performed, controlled by
deactivation of the compressor and solenoid valve, the connections are
pressure via a pressure switch connected to the Ultra 3PH Full three-
as shown in the following diagram.
phase module rather than UltraCella,
Connection and thepump
for operation compressor
down shuts down Connection for operation with thermostat
due to low pressure, the connections are as shown in the following
diagram.
Connection for operation pump down Connection for operation with thermostat
121

126

126
123

125

127

122

123

125

127
124

124
121

126

126
123

125

127

122

123

125

127
124

124
P P

P P
bridge

pressure switch
low pressure switch

liquid valve

bridge

pressure switch
low pressure switch

liquid valve
bridge

pump down pressure switch

downswitch

liquid valve

bridge

pump down pressure switch

downswitch

liquid valve
pressure

pressure
pump

pump
low

low
Fig. 9.c

With this configuration, when there is no cooling request from UltraCella

Fig. 9.a (Sv<St), the solenoid valve (terminals 126-127) and the compressor (KM3)
are simultaneously deactivated. In normal operation, when the pressure
With this configuration, when there is no cooling request from UltraCella switch measures measures the low pressure threshold, the compressor
(Sv<St), the solenoid valve (terminals 126-127) opens, while the is shut down.
compressor (KM3) remains on until the pressure switch measures the low
pressure threshold (TK1, terminals 124-125).

Fig. 9.b Fig. 9.d

Note: as the pressure switch is connected to the Ultra 3PH Full Nota: Do not enable pump down on UltraCella (set c7=0, H1≠5,
three-phase module, do not enable pump down on UltraCella (set c7=0, H5≠5).
H1≠5, H5≠5).

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 90

 ENG
Connections for pump down with simultaneous activation of the Connections for timed pump down
compressor and solenoid valve If the pump down procedure needs to be performed based on a time
If the pump down procedure needs to be performed, with simultaneous setting, with the solenoid valve connected to the Ultra 3PH Full three-
actvation and deactivation of the compressor and solenoid valve and phase module rather than UltraCella, the connections are as shown in
Connection
without forswitch,
a pressure operation pump down
the connections arewith simultaneous
as shown in the following the following diagram.
Connection for operation pump down by time
diagram.
start up of compressor and solenoid valve

122

128

109
125

129

110
124
122

126
123

125

127
124

N
L
bridge
bridge

liquid valve
liquid valve

Fig. 9.g

Fig. 9.e On UltraCella, configure:

• H1 = 5 (output AUX1, terminals 109-110, for pump down valve)
With this configuration, when there is no cooling request from UltraCella • c10 = 1 (timed pump down)
(Sv<St), the solenoid valve (terminals 126-127) and the compressor (KM3) • c7 > 0 (pump down time)
are simultaneously deactivated. With this configuration, when there is no cooling request from UltraCella
(Sv<St), the solenoid valve (terminals 109-110, output AUX1 on UltraCella)
opens, while the compressor (KM3) remains on for the time defined by
parameter c7

Fig. 9.f

Nota: Do not enable pump down on UltraCella (set c7=0, H1≠5,

H5≠5).
Fig. 9.h

91 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

 evaporator fans MV1:U 1 KM1:2

XP1

XA1
M
evaporator fans MV1:V 2 KM1:4

Term.
ENG
evaporator fans MV1:W 3 KM1:6
4 QF1:8/QF2:N1

9
8
7
6
5
3
2
defrost heaters RR1 5 KM2:2

11
10

PE2

103
102
101

109
108
107
106
105
104

116
115
114
113
112
111
110

120
119
118
117

127
126
125
124

142
141
140
129
128

147
146
143

162
161
160
defrost heaters RR1 6 KM2:4
defrost heaters RR1 7 KM2:6
defrost heaters RR1 8 QF1:8
compressor MV2:U 9 KM3:2

Kriwan
M
10

RS485 -
compressor MV2:V KM3:4

RS485 +
UX1 relay
compressor MV2:W 11 KM3:6

RS485 GND
Compressor

Pump Down
PE2

Solenoid valve
10.2.7 Terminal units

Defrost heaters
Evaporator fans

Ground terminal

PE109 Ground terminal

Number and description

Defrost probe NTC

Condensing fans 1

Condensing fans 2
XP1

Clicson evaporator fans

High/low Pressure switch
Fig. 10.l

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016

Oil compressor heater (Carter)

Safe thermostat evaporator fans

terminal block

0…10V for evaporator fans (GND)

Defrost probe NTC aux evaporator
0…10V for evaporator fans (signal)
Power supply 230Vac for UltraCella
19 19

1
condenser fans 1 MV3:1 101 XA1:103

M
18 18
condenser fans 1 MV3:2 102 QF2:N2/XA1:106

P
19 19

Pressure switch condensing fans partialization

partialization pressure switch condenser fan SP1 103 XA1:101/KM3:14
20 20
partialization pressure switch condenser fan SP1 104 XA1:105
20 20

1
condenser fans 2 MV4:1 105 XA1:104
M
18 18
condenser fans 2 MV4:2 106 XA1:108/XA1:102
21 21
crankcase heater RR2 107 KM3:62
18 18
crankcase heater RR2 108 XA1:106

-
-
-

-
-
-

-
-

-
-

-
-

-
-

-
-

-
38 38
aux 1 AUX1:1 109 KR2:11
37 37
aux 1 AUX1:2 110 KR2:14

Note
25 25
L

kriwan AP2:L 111 FU2:2/XA1:113

24 24
N

kriwan AP2:N 112 KR1:A2/FU1:2

25 25

92
kriwan AP2:11 113 XA1:128/XA1:111
28 28
kriwan AP2:14 114 XA1:115
P

28 28
pressure switch SP2 115 XA1:114
29 29
pressure switch SP2 116 KR1:A1
27 27

To supply UltraCella
security thermostat TS1 117 ??:J10/NO1
31 31
security thermostat TS1 118 KM2:A1
30 30
evaporator clicson SP3 119 ??:J10/NO2
33 33
evaporator clicson SP3 120 KM1:A1
29
121 ??:J11/C3/4/5
32
122 XA1:126/??:J11/NO3
35
123
P

35 35
pump down TK1 124
34 34
pump down TK1 125 KM3:A1
32 32

Connection RS485 Fieldbus to UltraCella

liquid valve YV1 126 XA1:122
24 24
liquid valve YV1 127 KM3:A2/XA1:129
25 25
ultracella ULTRACELLA:L 128 ??:J12/NC6/XA1:113
24 24
ultracella ULTRACELLA:N 129 XA1:127/KR2:A2
39 39
defrost probe ST1 140 ??:J2/U1
40 40
defrost probe ST1 141 XA1:143
41 41
defrost probe auxiliary evap. ST2 142 ??:J2/U2
40 40
defrost probe auxiliary evap. ST2 143 XA1:145/XA1:141
42 42
condenser probe ST3 144 ??:J2/U3
40 40
condenser probe ST3 145 ??:J2/GND/XA1:143
45 45
evaporator fans 0...10Vdc Y 7AP1:Y 146 ??:J2/U6
40 40
evaporator fans 0...10Vdc GND 7AP1:GND 147 KR1:11
46 46
control - AP1:J6/- 160 AP:-
47 47
control + AP1:J6/+ 161 AP:+
48 48
control GND AP1:J6/GND 162 AP:GND
26
PE109 TC1:PE
XA1

Normally closed. If active (open), evaporator fans are off and it’s not notified in UltraCella

Normally closed. If active (open), evaporator fans are off and it’s not notified in UltraCella
terminal block

Tab. 10.b
 ENG
11. SOFTWARE RELEASE
11.1 Software release table
Manual Availability Functions UltraCella Notes
release date Software
release
1.1 28/02/2014 Basic cold room management: compressor, defrost, evaporator fans, light, 1.1 UltraCella single digit display
2xAUX relays
Single digit display management
Commissioning UltraCella through both built-in LED display and pGD1
UltraCella Service
Commissioning through wizard on pGD1
Upload/Download parameters via USB key
Defrost schedule by RTC
HACCP alarms
Maximum and minimum temperature recording
Diagnosis: I/O status visualization
Second step compressor with automatic rotation
Evaporator fans in PWM mode (on/off ) with compressor off
Auxiliary evaporator management
Smart light management by door switch
Bowl heater activation
Condenser fan activation by temperature
Pump down management
Humidity probe reading
Pre-charged configurations (recipes)
Software update through pGD1
1.3 30/06/2014 Double digit display management 1.2 UltraCella double digit display (software
release 1.2) availability in production:
Data logging function (one temperature)
11/04/2014
Humidity ON/OFF output
Serial connection UltraCella - EVD EVO (only "start command")
Service menu on pGD1 (diagnosis)
Navigation improvements on both LED and pGD1 1.3 UltraCella software 1.3 availability in
production: 30/06/2014
Added alarm indication on USB functions (in case of bad working)
Commissioning EVD EVO via UltraCella
Defrost by dI (fixed interval time) enable with RTC defrost set too
Limit and default parameter setting change (H0, /t2, dd, Fd)
0…10V output for variable speed evaporator fans
"Bugfixing: 1.4 UltraCella software 1.4 availability in
Input B5 Humidity reading production: 03/11/2014
High/low temp. alarm delay
EVD communication in manual OFF status"
1.5 30/01/2015 3PH expansion module management (one to one) 1.5 UltraCella software 1.5 availability in
production: 22/12/2014
Data logging: 2 selectable temperatures, variable sampling time
Log of stored alarms
BMS serial line: Modbus / Carel protocols selectable
Software update by built-in LED display
Addition of pGD texts in German and French
New default /A2=1 (defrost probe configured in B2)
New default settings for EVD module (push from UltraCella)
Door switch disabling (new question in wizard and new parameter A3)

93 UltraCella +0300083EN - rel. 1.7 - 07.01.2016

ENG
1.6 31/10/2015 0 to 10 V output for variable speed condenser fans managed by pressure/ 1.6 UltraCella software 1.6 availability in
temperature + floating condensing) algorithm production: 27/07/2015
Heating/cooling control with dead band
EVDice configuration from UltraCella
Generic functions
Auxiliary output activation by time bands
Set point variation by time bands / from digital input
Set point ramps
Humidity data logging
High / low humidity alarm management
Possibility to disable alarms Ed1 / Ed2 (parameter A8)
Additional pGD texts in Spanish
Alarms on high/low humidity levels
AUX1/AUX2 icon on active display when corresponding relay output
active
PMU variable (% valve opening in manual mode for EVD EVO) visible on
built-in LED display
1.7 07/01/2016 Improved EVDice management: management of signatures to protect 1.7 UltraCella software 1.7 availability in
custom configurations production: 20/11/2015
Configuration of BMS serial parameters
Language selection as first question in wizard
Addition of EVD EVO MOP parameters on UltraCella LED display
New default configuration for communication between UltraCella and
3PH modules
Door microswitch disabled by default (A3=1)
Parameter IPE (enable EVDice communication with UltraCella) available
on supervisor

UltraCella +0300083EN - rrel. 1.7 - 07.01.2016 94

 UltraCella +0300083EN - rel. rel. 1.7 - 07.01.2016

Agenzia / Agency:

CAREL INDUSTRIES S.p.A.

Via dell’Industria, 11 - 35020 Brugine - Padova (Italy)
Tel. (+39) 049.9716611 - Fax (+39) 049.9716600
e-mail: [email protected] - www.carel.com