Technical data sheet LMQ24A-SR

Modulating damper actuator for adjusting

dampers in technical building installations

• Air damper size up to approx. 0.8 m²

• Torque motor 4 Nm
• Nominal voltage AC/DC 24 V
• Control modulating 2...10 V
• Position feedback 2...10 V
• Running time motor 2.5 s

Technical data

Electrical data Nominal voltage AC/DC 24 V

Nominal voltage frequency 50/60 Hz
Nominal voltage range AC 19.2...28.8 V / DC 21.6...28.8 V
Power consumption in operation 13 W
Power consumption in rest position 2W
Power consumption for wire sizing 23 VA
Power consumption for wire sizing note Imax 20 A @ 5 ms
Connection supply / control Cable 1 m, 4x 0.75 mm²
Parallel operation Yes (note the performance data)

Functional data Torque motor 4 Nm

Operating range Y 2...10 V
Input impedance 100 kΩ
Position feedback U 2...10 V
Position feedback U note Max. 0.5 mA
Position accuracy ±5%
Direction of motion motor selectable with switch 0/1
Direction of motion note Y = 0 V: At switch position 0 (ccw rotation) /
1 (cw rotation)
Manual override with push-button, can be locked
Angle of rotation Max. 95°
Angle of rotation note can be limited on both sides with adjustable
mechanical end stops
Minimum angle of rotation Min. 30°
Running time motor 2.5 s / 90°
Adaptation setting range manual (automatic on first power-up)
Sound power level, motor 54 dB(A)
Mechanical interface Universal shaft clamp 8...26.7 mm
Position indication Mechanical, pluggable

Safety data Protection class IEC/EN III, Safety Extra-Low Voltage (SELV)
Power source UL Class 2 Supply
Degree of protection IEC/EN IP54
Degree of protection NEMA/UL NEMA 2
Enclosure UL Enclosure Type 2
EMC CE according to 2014/30/EU
Low voltage directive CE according to 2006/95/EC
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14

www.belimo.com LMQ24A-SR • en-gb • 2023-12-13 • Subject to change 1/5

 Technical data sheet LMQ24A-SR

Technical data
Safety data UL Approval cULus according to UL60730-1A, UL60730-2-14
and CAN/CSA E60730-1
The UL marking on the actuator depends on
the production site, the device is UL-compliant
in any case
Hygiene test According to VDI 6022 Part 1 / SWKI VA
104-01, cleanable and disinfectable, low
emission
Type of action Type 1
Rated impulse voltage supply / control 0.8 kV
Pollution degree 3
Ambient humidity Max. 95% RH, non-condensing
Ambient temperature -30...40°C [-22...104°F]
Ambient temperature note Caution: 40...50°C utilisation possible only
under certain restrictions. Please contact your
supplier.
Storage temperature -40...80°C [-40...176°F]
Servicing maintenance-free

Weight Weight 0.99 kg

Safety notes

• This device has been designed for use in stationary heating, ventilation and air-conditioning
systems and must not be used outside the specified field of application, especially in aircraft
or in any other airborne means of transport.
• Outdoor application: only possible in case that no (sea) water, snow, ice, insolation or
aggressive gases interfere directly with the device and that it is ensured that the ambient
conditions remain within the thresholds according to the data sheet at any time.
• Only authorised specialists may carry out installation. All applicable legal or institutional
installation regulations must be complied with during installation.
• The device may only be opened at the manufacturer's site. It does not contain any parts that
can be replaced or repaired by the user.
• Cables must not be removed from the device.
• Self adaptation is necessary when the system is commissioned and after each adjustment of
the angle of rotation (press the adaptation push-button once).
• To calculate the torque required, the specifications supplied by the damper manufacturers
concerning the cross-section and the design, as well as the installation situation and the
ventilation conditions must be observed.
• The device contains electrical and electronic components and must not be disposed of as
household refuse. All locally valid regulations and requirements must be observed.

Product features

Operating mode The actuator is connected with a standard control signal of 0...10 V and drives to the position
defined by the control signal. Measuring voltage U serves for the electrical display of the
damper position 0...100% and as control signal for other actuators.

Simple direct mounting Simple direct mounting on the damper shaft with a universal shaft clamp, supplied with an
anti-rotation device to prevent the actuator from rotating.

Manual override Manual override with push-button possible (the gear train is disengaged for as long as the
button is pressed or remains locked).

Adjustable angle of rotation Adjustable angle of rotation with mechanical end stops. A minimum permissible angle of
rotation of 30° must be allowed for.

www.belimo.com LMQ24A-SR • en-gb • 2023-12-13 • Subject to change 2/5

 Technical data sheet LMQ24A-SR

Product features
High functional reliability The actuator is overload protected, requires no limit switches and automatically stops when
the end stop is reached.

Home position The first time the supply voltage is switched on, i.e. at the time of commissioning, the actuator
carries out an adaptation, which is when the operating range and position feedback adjust
themselves to the mechanical setting range.
The detection of the mechanical end stops enables a gentle approach to the end positions,
thus protecting the actuator mechanics.
The actuator then moves into the position defined by the control signal.

Adaptation and synchronisation An adaptation can be triggered manually by pressing the "Adaptation" button. Both
mechanical end stops are detected during the adaptation (entire setting range). Automatic
synchronisation after pressing the manual override button is configured. The synchronisation
is in the home position (0%).
The actuator then moves into the position defined by the control signal.

Accessories

Electrical accessories Description Type

Auxiliary switch 1x SPDT add-on S1A
Auxiliary switch 2x SPDT add-on S2A
Feedback potentiometer 140 Ω add-on P140A
Feedback potentiometer 1 kΩ add-on P1000A
Feedback potentiometer 10 kΩ add-on P10000A
Adapter for auxiliary switch and feedback potentiometer, Multipack 20 Z-SPA
pcs.
Signal converter voltage/current 100 kΩ 4...20 mA, Supply AC/DC 24 V Z-UIC
Positioner for wall mounting SGA24
Positioner for built-in mounting SGE24
Positioner for front-panel mounting SGF24
Positioner for wall mounting CRP24-B1
Mechanical accessories Description Type
Actuator arm for standard shaft clamp (one-sided) AH-25
Shaft extension 240 mm ø20 mm for damper shaft ø8...22.7 mm AV8-25
Ball joint suitable for damper crank arm KH8 KG8
Ball joint suitable for damper crank arm KH8 / KH10 KG10A
Damper crank arm Slot width 8.2 mm, clamping range ø10...18 mm KH8
Shaft clamp one-sided, clamping range ø8...26 mm with insert, K-ENMA
Multipack 20 pcs.
Shaft clamp one-sided, clamping range ø8...26 mm, Multipack 20 pcs. K-ENSA
Shaft clamp reversible, clamping range ø8...20 mm K-NA
Form fit insert 8x8 mm, Multipack 20 pcs. ZF8-NMA
Form fit insert 10x10 mm, Multipack 20 pcs. ZF10-NSA
Form fit insert 12x12 mm, Multipack 20 pcs. ZF12-NSA
Form fit insert 15x15 mm, Multipack 20 pcs. ZF15-NSA
Form fit insert 16x16 mm, Multipack 20 pcs. ZF16-NSA
Mounting kit for linkage operation for flat installation ZG-NMA
Anti-rotation mechanism 180 mm, Multipack 20 pcs. Z-ARS180
Baseplate extension for NM..A to NM.. Z-NMA
Position indicator, Multipack 20 pcs. Z-PI
* Adapter Z-SPA
It is imperative that this adapter will be ordered if an auxiliary switch or a feedback
potentiometer is required and if at the same time the shaft clamp is installed on the rear side
of the actuator (e.g. with short shaft installation).

www.belimo.com LMQ24A-SR • en-gb • 2023-12-13 • Subject to change 3/5

 Technical data sheet LMQ24A-SR

Electrical installation

Supply from isolating transformer.

Parallel connection of other actuators possible. Observe the performance data.

Wire colours:
1 = black
2 = red
3 = white
5 = orange

Wiring diagrams
AC/DC 24 V, modulating

Signal cable lengths

A = Actuator
C = Control unit (controlling unit)
L1 = Connecting cable of the
actuator
L2 = Customer cable
Ltot = Maximum signal cable
length

Note:
When several actuators are
connected in parallel, the
maximum signal cable length
must be divided by the number
of actuators.

A = Actuator
C = Control unit (controlling unit)
L1 = Connecting cable of the
actuator

Note:
There are no special restrictions
on installation if the supply and
the data cable are routed
separately.

www.belimo.com LMQ24A-SR • en-gb • 2023-12-13 • Subject to change 4/5

 Technical data sheet LMQ24A-SR

Operating controls and indicators

1 Direction of rotation switch

Switch over: Direction of rotation changes

2 Push-button and LED display green

Off: No power supply or malfunction

On: In operation
Press button: Triggers angle of rotation adaptation, followed by standard mode

3 Push-button and LED display yellow

Off: Standard mode

On: Adaptation or synchronisation process active
Press button: No function

4 Manual override button

Press button: Gear train disengages, motor stops, manual override possible
Release Gear train engages, synchronisation starts, followed by standard
button: mode

Check power supply connection

2 Off and 3 On Possible wiring error in power supply

Installation notes

Negative torque Max. 50% of the torque (Caution: Application possible only with restrictions. Please contact
your supplier.)

Dimensions

Spindle length

Min. 40

Min. 20

Clamping range

• *Option: Shaft clamp mounted below

(accessories K-NA needed)
• *Option: Shaft clamp mounted below: If an
auxiliary switch or a feedback potentiometer is
used the adapter Z-SPA is required.

www.belimo.com LMQ24A-SR • en-gb • 2023-12-13 • Subject to change 5/5