TABLE OF CONTENTS

SECTION A-COIN AND CREDIT EQUIPMENT

SECTION B-SELECTOR SWITCH AND ELECTRIC SELECTOR

-
SECTION C RECORD CHANGER ADJUSTMENTS

-
SECTION D CABINET

SECTION E - SEQUENCE OF OPERATIONS

SECTION F - TROUBLE SHOOTING

SECTION G - ELECTRICAL AND SOUND SYSTEMS

THE WURLITZER COMPANY NORTH TONAWANDA. NEW YORK

-.- -- -- .
. --

SECTION A

WARRANTV
The component p a r t s of automatic phonographs and accessory equipment manu-
factured by the Wurlitzer Company a r e warranted to be f r e e from defects in
material and workmanship and to operate properly under normal use and con-
ditions, a s follows:

(A) Mechanical p a r t s (Excluding coin equipment) f o r a

period of one year from date of delivery by the Dis-
tributor to his customer.

(B) Coin equipment and electrical p a r t s (Including such

parts a s speakers, volume control assemblies, pick-
up assemblies, amplifiers, motors, junction box a s -
semblies, and a l l wiring) for a period of t h r e e
months from date of delivery by the Distributor to
his customer.

(C) Cabinets ( S u b j e c t to the Company's inspection and

determination a s to defect) for a p e r i o d of three
months from date of delivery by the Distributor to
his customer,

The company's liability under this warranty i s limited to replacement, f r e e

of charge, F.O.B. North Tonawanda, New York, of any p a r t o r p a r t s which
prove defective within the limitations of said warranty. The Company shall
not be liable for damages of any nature due to delayed shipment, o r defective

THE COMPANY
WURLITZER N O R T H TONAWANDA. N Y

Page A
 SECTION A

COlN AND CREDIT EQUIPMENT

SLUG REJECTOR

C O l N REGISTER M E C H A N I S M

Reject Rod Adjustment.. .............................................................. Page 2A

Slug Rejector Mounting Plate Adjustment ...............................................Page 2A
Coin Switch Adjustments .............................................................. Page 3A
Coin Register Mechanism Adjustments .................................................Page 4A
Stop Lever and Indexing Strip Adjustment ............................................... Page 4A:
Cancel Stroke Adjustment .............................................................
Page 5A
Cancel Pawl Stop Bracket Adjustment ................................................... Page 6A
Switch and Bracket Assembly Adjustment ...............................................Page 6A
Key Switch Adjustment. .............................................................. Page 7A
L . P . Switch Adjustment ..............................................................
Page 7A
Top Tune Switch Adjustment.. ......................................................... Page 7A
Coin Register Mechanism Illustrated Parts L i s t .........................................
Page 8A
Slug Rejector Mounting Assembly Illustrated Parts List ..................................Page 9A

WURLITZER Page 1 A
SECTION A

REJECT ROD ADJUSTMENT

Open phonograph dome assembly and remove the program holder, then close dome assembly. De-
press reject button flrmly. Viewing SLUG REJECTOR through the dome assembly, verify that the
BRACKET and CAM ASSEMBLY 1s fully depressed with 1/4" of the reject button remaining.
Should adjustment of the REJECT ROD be necessary, loosen REJECT ROD ADJUSTING NUTS and po-
sition the REJECT ROD as requlred for proper operation. Tighten REJECT ROD ADJUSTING NUTS.

RETAINING SPRING
0

;5 REJECT ROD ADJUSTING NUTS

MOUNTING SCREWS
(Typical) - BRACKET and CAM ASSEMBLY

SLUG REJECTOR

SLUG REJECTOR
MOUNTING PLATE
- ANGLE and GUARD ASSEMBLY

SLUG REJECTOR MOUNTING PLATE ADJUSTMENT

Be sure that the phonograph is positioned on a level surface prior to making any adjustments to the
SLUG REJECTOR MOUNTING PLATE. Should it be necessary to compensate for uneven footing, the
following methods may be used.

1. Side to side leveling of the phonograph may be accomplished by placing blocks o r strips under
the casters on the low side of the cabinet. Check SLUG REJECTOR for proper coin acceptance.
2. Front to back leveling of the SLUG REJECTOR may be accomplished by loosening the seven
MOUNTING SCREWS andpositioningthe SLUG REJECTOR PLATE a s required. TightenMOUNT-
ING SCREWS. Check SLUG REJECTOR for proper coin acceptance.

NOTE

Access to all MOUNTING SCREWS is accomplished by lifting the RETAINING SPRING, moving the top
of the SLUG REJECTOR to the left then lifting out.

Page 2A WURLITZER
COIN SWITCH ADJUSTMENTS

Remove ANGLE and GUARD ASSEMBLY to obtain access to coin switch.

With coin switch paddles resting flush

against bottom of slug rejector, verify
spacing between switch mounting bracket
and cover and clip assembly is 1/4"

Tension of the long movable blades must

be sufficient to hold the coin switch pad-
dles against bottom of slug rejector.

Thestiffener blades should be set to pro-

vide 1/32" opening betweenshort andlong
movable contact blades .

The short blades must bear against stiff-

eners with sufficient tension to prevent
vibration. This should be approximately
one gram on the 10 cent blade and two to
three grams on the 5, 25 and 50 cent
blades.

E . When phonograph is equipped with W u r -

litzer Income Computer, adjust r e a r
stiffener blades to provide opening be-
tween contacts a s stated in step C .

The tension of the long movable blades should be adjusted s o a thin coin, when stopped on it's coin
paddle by holding the paddle up, will upon releasing the paddle, actuate the movable blade, close the
contacts then clear paddle.

1. Install SLUG REJECTOR in phonopaph and apply power

2. Test each individual coin track ten consecutive times with coins of varied wear. If a coin fails
to register, that particular coin switchshould be examined and, if necessary, readjusted. Check
SLUG REJECTOR for proper alignment.

A pulse of more than five seconds duration should normally trip the circuit breaker in the coin mag-
net circuit.

WURLITZER Page 3A
 -
SECTION A

COIN REGISTER MECHANISM ADJUSTMENTS -

CAUTION -
MAKE ALL ADJUSTMENTS ON T H E COIN REGISTER MECHANISM WITH THE POWER O F F .
-
A . ACCUMULATOR WHEELS in a t rest
condition (all credits cancelled off).

B. Studs of LEVER, HUB and STUD AS -

SEMBLIES engaged with the first
tooth of their respective ACCUMU-
ACCUMULATOR LATOR WHEELS.
WHEELS
LEVER, HUB and
STUD ASSEMBLIES

CANCELWHEEL C . CANCEL WHEEL DRIVE PIN rest-

DRIVE PIN ing squarely against the edge of the
three ACCUMULATOR WHEELS.

If the above conditions cannot be met, examine the coin register mechanism for bent studs and/or
sprung frame. Corrections should be made before proceeding with adjustments.

STOP L E V E R AND INDEXING STRIP ADJUSTMENT

Prior to making any adjustments to STOP LEVERS and/or INDEXING STRIPS, loosen BRACKET and
SWITCH ASSEMBLY ADJUSTING SCREW and move BRACKET and SWITCH ASSEMBLY fully clockwise.

BRACKET and SWITCll ASSEMBLY , Set STOP LEVERS a t 7 credits.

Release the three LEVER HUB and
STUD ASSEMBLIES allowing the
INDEX STRIP three ACCUMULATOR WHEELS to
ADJUSTING advance to the 7 credit position. Re-
SCREWS lease the threc LOCKOUT HUB and
LEVERS.
CANCEL WHEEL DRIVER PIN must
BRACKET and rest squarely against the edge of the
SWITCH ACCUMULATOR WHEELS.
ASSEMGLY
Stud should fall squarely in the
seventh credit recess of the AC-
CUMULATOR WHEELS. If adjust-
CANCEL WHEEL ment is required, loosen INDEX
DRIVER PIN STRIP ADJUSTING SCREWS on the
10, 25, and 50 cent index strips and
move the index strips a s required.
ACCUMULATOR LOCKOUT HUB Tighten INDEX STRIP ADJUSTING
and LEVER
SCREWS.

Page 4A WURLITZER
C A N C E L STROKE ADJUSTMENT

Prior to making this adjustment, loosen the CANCEL SOLENOID ADJUSTING SCREWS and back off the
CANCEL SOLENOID, then manually actuate the 50 CENT LEVER, HUB and STUD ASSEMBLY to per-
mit the 50 CENT ACCUMULATOR WHEEL and the CANCEL WHEEL to advance to the seven credit
position.

A . Manually actuate the CANCEL SOLENOID B. The 50 CENT ACCUMULATOR WHEEL must
PLUNGER at this point. return one full tooth plus MINIMUM OVER-

\
\ TRAVEL between the ESCAPEMENT STUD
and the tooth of the 50 CENT ACCUMULA-
CANCEL\ PAWL CAM CAM ADJUSTINI TOR WHEEL.
\ SCREW

\ 50CENTACCUMULATOR
IVHEEL

CANCEL
SOLENOID
PLUNGER

CANCEL
SOLENOID ESCAPEMENT
STUD

CANCEL H/g
SOLENOID
ADJUSTING
SCREWS

~ 1 MINIMUM 50 CENT LEVER. I-IUB

CANCEL WHEEL OVERTRAVEL and STUD ASSEhlBLY

C . Should adjustment be necessary, loosen the D . Position CANCEL SOLENOID whlle manual-
CAM ADJUSTING SCREW then turn CAM to ly actuating the CANCEL SOLENOID PLUNG-
provide MINIMUM OVERTRAVEL require- ER a s in step A . The CANCEL PAWL must
ment of step B. Tighten CAM ADJUSTING be held firmly against the CAM. Move the
SCREW and its locknut (located on back of CANCEL SOLENOID up in its elongated
mounting plate). mounting holes until the CANCEL SOLEN-
OID PLUNGER bottoms in the CANCEL
SOLENOID. Tighten CANCEL SOLENOID
ADJUSTING SCREWS.

Check each tooth of the 10, 25 and 50 cent accumulator wheels for proper cancel action. There will
be considerable overtravel a s the last tooth is cancelled. This is normal. Should readjustment be
required for proper cancel action, repeat entire CANCEL STROKE ADJUSTMENT procedure.

WURLlTZER Page 5 A
SECTION A

CANCEL PAWL STOP BRACKET ADJUSTMENT

Prior to making this adjustment, manually actuate the 50 CENT LEVER, HUB and STUD ASSEMBLY to
permit the 50 CENT ACCUMULATOR WHEEL and the CANCEL WHEEL to advance to the seven credit
position.

CANCEL PAWL CANCELPAWL

STOP BRACKET
A . Loosen the STOP BRACKET ADJUSTING
SCREWS and manually actuate the CANCEL
SOLENOID PLUNGER until the CANCEL
STOP BRACKET PAWL engages the seventh tooth of the CAN-
ADJUSTING SCREWS CEL WHEEL.

1/3 TOTAL
TOOTH DEPTH

CANCEL SOLENOID B. Adjust the CANCEL PAWL STOP BRACKET

PLUNGER to permit the CANCEL PAWL to engage the
seventh tooth of the CANCEL WHEEL at 1/3
TOTAL TOOTH DEPTH as shown.

CANCEL
I WHEEL
C . Verify that during cancel operation, the
CANCEL PAWL is free (no drag) from the
CANCEL PAWL STOP BRACKET a s shown.

SWITCH AND BRACKET ASSEMBLY ADJUSTMENT

The SWITCH and BRACKET ASSEMBLY (25 cent credit switch) provides crediting for two quarter
operation. If adjustment of the SWITCH and BRACKET ASSEMBLY is required, perform the following:

SWITCH and BRACKET ASSEMBLY

ADJUSTING SCREW A. Loosen the SWITCH and BRACKET ASSEM-
BLY ADJUSTING SCREW.
B. Manually actuate the 25 CENT LEVER, HUB
and STUD ASSEMBLY topermit the 25 CENT
ACCUMULATOR WHEEL to advance to thc
normally used credit position.
25 CENT
ACCUMULATOR C. Adjust the SWITCH and BRACKET ASSEM-
WHEEL BLY s o that the 25 CENT SWITCII closes
with 1/32" overtravel with the 25 CENT
ACCUMULATOR WHEEL in the credit po-
sition dictated by step B.
D . Manually actuate the CANCEL SOLENOID to
SWITCH and BRACKET 2 j CENT SWI'I'CII cancel one credit. The 25 CENT SWITCH
ASSEMBLY should open with 1/32" clearance between
contacts. Tighten the SWITCH and BRACKET
ASSEMBLY ADJUSTING SCREW.

Page 6A WURLITZER
KEY SWITCH. L.P. SWITCH AND TOP TUNE SWITCH ADJUSTMENTS

Prior to making any of the following switch adjustments, set all pricing stop levers to coincide with
coin denomination instruction label.

TOP TUNE TOP TUNE SWITCH

SWITCH ADJUSTING SCREW

KEY SWITCH
ADJUSTING SCREWS
CANCEL WHEEL

L. P. SWITCH
ADJUSTING KEY SWITCH
SCREW

KEY SWITCH ADJUSTMENT

A. With all credits caucelled off, loosen the KEY SWITCH ADJUSTING SCREWS and position the vee
portion of thc long blade s o that it rests in the bottom and to the left hand side of the notch of
the CANCEL WHEEL with 1/32" opening between contacts.
B. Manually actuate the 10 CENT LEVER, HUB and STUD ASSEMBLY to permit the 10 CENT AC-
CUMULATOR WHEEL and the CANCEL WHEEL to advance to the one credit position. The KEY
SWITCH should close with good wiping action.
C. Manually actuate the CANCEL SOLENOID PLUNGER and cancel off one credit. Verify that the
KEY SWITCH opens with 1/32" clearance between contacts. Tighten the KEY SWITCH ADJUST-
ING SCREWS.

L.P. SWITCH ADJUSTMENT

A. Manually actuate the 25 CENT LEVER, HUB and STUD ASSEMBLY to permit the 25 CENT AC-
CUMULATOR WHEEL and the CANCEL WHEEL to advance to the 25 cent credit position.
B. Loosen L.P. SWITCH ADJUSTING SCREW and position the L.P. SWITCH so that the switch
closes, with good wiping action, on the 25 cent credit position.
C . Manuallyactuate theCANCEL SOLENOID PLUNGERand cancel off one credit. The L.P. SWITCH
should open with approximately .025" clearance between contacts. Tighten L.P. SWITCH AD-
JUSTING SCREW.

TOP TUNE SWITCH ADJUSTMENT

A. Manually actuate the 50 CENT LEVER, HUB and STUD ASSEMBLY to permit the 50 CENT AC-
CUMULATOR WHEEL and the CANCEL WHEEL to advance to the 50 cent credit position.
B. Loosen the TOP TUNE SWITCH ADJUSTING SCREW and position the TOP TUNE SWITCH so that
the switch closes, with good wiping action, in the 50 cent credit position.
C. Manually actuate the CANCEL SOLENOID PLUNGER and cancel off one credit. Verify that the
TOP TUNE SWITCH opens with approximately .025" clearance between contacts. Tighten the
TOP TUNE SWITCH ADJUSTING SCREW.

WURLITZER Page 7A
SECTION A

COIN REGISTER MECHANISM

Brace, Door and Front Plate Link Solenoid
Screw, 6-32 x 1/4 HEX SEM . Retaining Ring
Screw, 6-32 x 1/4 HEX SEM. 23 Cotter Pin
Stop Lever and Spring Assembly (3) Washer
Indexing Strip, 10 cent Pin, Solenoid Shaft
Indexing Strip, 25 cent Pivot Arm and Pawl Assembly
Indexing Strip, 50 cent Pivot Pin, Pawl
Washer (6) Retaining Ring
Screw, 4-40 x 3/16 HEX SEM. (6) Washer
Spacer, Lockout Levers Washer
Lockwasher #8 Spacer
Spring Spring, Pawl
Switch Adjustment Cam
Hub and Lever Assembly, Lockout (3) Screw, 6-32 x 5/8 HEX SEM.
Shaft, Lockout Levers Lockwasher #6
Back Plate Nut 6-32
Screw, 6-32 x 1/4 HEX SEM. (3) Mounting Bracket and Switch Assembly
Mounting Bracket, Magnets Switch Assembly
Screw, 6-32 x 1/4 HEX SEM. Mounting Bracket
Coil Assembly Screw, 6-32 x 1 / 4 HEX SEM.
Lever, Hub and Stud Assembly (3) Washer
Retaining Ring Cancel Wheel and Mounting Plate Assembly
Spacer, Latch Lever (2) Key Switch and Bracket Assembly
Spring (3) Switch Assembly
Spring, Accumulator Wheel (3) Mounting Bracket
Accumulator Wheel and Hub Assembly (3) Screw, 6-32 x 3/16 HEX SEM. (2)
Adjusting Plate and Switch Assembly Washer (2)
Switch Assembly Shaft, Accumulator Wheel
Adjustment Plate Retaining Ring (2)
Screw, 6-32 x 1/4 HEX SEM. Mounting Bracket and Switch Assembly
Washer Switch Assembly
Relay, Socket Mounting Bra.cket
Retaining Spring Screw, 6-32 x 1/4 HEX SEM.
Handle, Coin Mechanism Washer
Screw, 6-32 x 1/4 HEX SEM . (2) Relay, Red
Spring, Solenoid Return Screw, 6-32 x 3/8 Bind Nylon
Eyelet (2) Strain Relief
Stop Bracket, Pawl Solenoid, Cancel
Screw, 6-32 x 3/16 HEX SEM . (2) Circuit Breaker
Washer Palnut
Lockwasher
Plug -12 W
Receptacle -6

Page 8A WURLITZER
 SECTION A

. .
.::.:....::.:..:.:.:.:...::.:.,.::..,.::.
D.

*.:.:.....
....
s :p,.
t.:. 1

Cover and Clip Assembly Mounting Plate, Slug Rejector

Cable Clamp (2) Screw 8 x 1 HEX A (3)
Screw, 8-32 x 1 / 4 HEX SEM. (2) Washer (3)
Locating Pin and Catch Assembly Grommet (3)
Screw, 8-32 x 3/16 HEX SEM. (2) Spacer (3)
Lever, Reject Rod Actuator and Bracket Assembly
Retaining Ring Shaft
Actuator and Pin Assembly Spring
Spring Retaining Ring (2)
Washer Angle and Guard Assembly
Retaining Ring Thumbscrew (2)
Coin Entry Chute Coin Switch
Screw, 6-32 x 1/2 HEX SEM. (3) Screw, 6 x 1/2 HEX TYPE Z
Screw, 6-32 x 3/8 HEX SEM. Spacer (2)
Washer (6) Spacer
Nut 6-32 (4) Speednut
Mounting Bracket Shaft
Screw, 8-32 x 1 / 4 HEX SWAGE(2) Copper Washer
Mounting Bracket, Lower Long Paddle
Screw, 8-32 x 1 / 4 HEX SEM.(2) Spacer
Reject Rod Copper Washer
Pivot Pin Copper Washer
Retaining Ring (4) Short Paddle
Nut (2) Iron Washer
Lockwasher (2) Iron Washer
Retaining Spring, Slug Rejector Mounting Bracket and Spacer Assembly
Screw, 8-32 x l / 4 HEX SEM . (2) Screw, 8-32 x 1 / 4 HEX SEM.
Washer Screw, 8-32 x 3/16 HEX SEM.
Mounting Plate and Bracket Assembly Washer (2)
Screw, 8-32 x 5/16 HEX SEM. (2) Brace, Support Bracket
Screw, 8-32 x 1/4 HEX SEM. (4) Screw, 8-32 x 1 / 4 HEX SEM.
Washer (5) Bracket and Pin Assembly
Shipping Clip, Slug Rejector Screw, 8-32 x 1 / 4 HEX SEM.
Screw, 8-32 x 5/16 HEX SEM. Screw, 8-32 x 3/8 HEX SEM.
Washer

Page 9A
 SECTION A

SPECIFICATIONS
WURLITZER
STATESMAN SERIES
100 - 160 - 200 SELECTION PHONOGRAPHS

CABINET DIMENSIONS
Height 53 1/2" Depth 24" Width 40 7/8"

DOME LOCK KEY. . . .RW 105

CASH BOX LOCK. . . .Ace WCX Series
DOLLAR BILL CASH BOX LOCK. . . .Ace WCX Series
POWER REQUIREMENTS
Standby 117 Volts Operational 117 Volts
60 Hertz 60 Hertz
200 VA (115 Watts) 375 VA (250 Watts)
CABINET ILLUMINATION
1 - 25 Watt Fluorescent
1 - 30 Watt Fluorescent
CREDIT EQUIPMENT
Slug Rejector. ..
.National Simplex IV
Dollar Bill Accepter. ..
.National Simplex 100
Credit Unit. ..
.Wurlitzer 4 Coin Convertible Playrak
RECORD CHANGER
Wurlitzer Wurlamatic
Turntable Speed. ..
.33.3 and 45 Automatic Intermixed
Records. ..
.7" - 33.3 and 45 W M
Record Library
100 Selection Phonograph. ..
.50 record capacity
160 Selection Phonograph. ..
.80 record capacity
200 Selection Phonograph. ..
,100 record capacity
-
KEYBOARD 200 Selection Phonographs
LP selections can be programmed in the A only o r A and B sections 1 thru 0 .
Minimum LP programming 5 LP records, 10 selections .
Maximum LP programming 10 LP records, 20 selections .
Automatic Programmer (when phonographs a r e s o equipped).
Gold Button selects records El-E3-E5 and F1-F3-F5, also E7-E9 and F7-F9 if s o desired.
Red Button selects records J1 -J3-J5 and K1 -K3-K5, also J7-J9 and K7-K9 if s o desired.
The Automatic Programmer can be optionally s e t f o r six, eight o r ten selections in the E - F
and J-K sections .
WURLITZER Page B
 KEYBOARD SELECTOR SWITCH, JUNCTION BOX,
AND TOP TUNE EQUIPMENT

KEYBOARD SELECTOR SWITCH ASSEMBLY,

JUNCTION BOX TOP TUNES UNIT

Connector Link Plate Adjustment.. ....................................................Page 2B

Preliminary Adjustment of the Latch Solenoid ......................................... Page 2B
Latch Solenoid Stop Bracket Adjustment ............................................... Page 3B
Letter and Number Latch Lever Adjustment ........................................... Page 3B
Final Latch Solenoid Adjustment ..................................................... Page 4B
Latch Solenoid Switch Adjustment .................................................... Page 4B
Letter and Number Series Switch Adjustment .......................................... Page 5B
Letter and Number Latch Switch Adjustment ...........................................Page 5B
Selector Switch Assembly Illustrated Parts List ........................................ Page 6B
Junction Box Assembly Illustrated Parts List ...........................................Page 9B

Top Tune Unit and Mounting Bracket Assembly Illustrated Parts List .................... Page 10B
WURLITZER Page 1B
 -
SECTION B

CONNECTOR LlNK PLATE ADJUSTMENT NUMBERLATCHLEVER

ADJUSTING SCREW

4 . Loosen t h e LETTER and NUMBER LATCH

LEVER ADJUSTING SCREWS.

LETTERLATCHLEVER
ADJUSTING SCREW

B. Loosen NUMBER and LETTER CONNEC-

TOR LINK PLATE ADTUSTING SCREWS.

LETTERCONNECTOR
LlNK PLATE ADJUSTING

NUMBERCONNECTOR
LINK PLATE ADJU
SCREWS
LETTER LlNK and
NUMBER LINK and LEVER ASSEMBLY
LEVER ASSEMBLY

C . Fully depress a number bunon, then po- D. Fully d e p r e s s a l e t t e r button, then posi-
s ~ t i o nthe NUMBER LINK and LEVER AS- tion the LETTER LINK and LEVER AS-
SEMBLY in a v e r t i c a l posltlon. T ~ g h t e n SEMBLY in a v e r t i c a l uosition. Tighten
the NUMBER CONNECTOR LINK PLATE the LETTER CONNECIOR LINK PLATE
ADJUSTING SCREWS. ADJUSTING SCREWS.

PRELIMINARY ADJUSTMENT OF THE LATCH SOLENOID

A. T u r n the RELEASE LEVER ADJUSTING B. Loosen the LATCH SOLENOID ADJUSTING

SCREW in two t u r n s . \ \I SCREWS.

RELEASE LEVER LATCH SOLENOID

TAB ADJUSTING SCREWS

LATCH SOLENOID

LATCH SOLENOID
LEFT HAND PLUNGER
TRIP LEVER

C. Manually hold the LATCH SOLENOID

PLUNGER f i r m l y bottomed in the LATCH
SOLENOID, then s e t the LATCH SOLENOID
to provide 3/64" maximum clearance be-
tween the RELEASE LEVER TAB and the
L E F T HAND TRIP LEVER. Tighten the
LATCH SOLENOID ADJUSTING SCREWS.

Page 20 WURLITZER
 SECTION B

LATCH SOLENOID STOP BRACKET ADJUSTMENT

A . Verify Lhat the RELEASE LEVER is in its B. Loosen the LATCH SOLENOID STOP
normal r e s t position. BRACKET ADJUSTING SCREWS.
RELEASE LEVER
LATCH SOLENOID STOP
BRACKET ADJUSTING NUMBERLATCH
SCREWS LEVER
LATCH SOLENOID
STOP BRACKET

LETTER LATCH
LEVER

1/64" CLEARANCE 1/64" CLEARANCE

.
LEFT HAND TRIP RELEASE LEVER RIGHT HAND
LEVER ADJUSTING SCREW TRIP LEVER

C. Position LATCH SOLENOID STOP BRACKET D. Back off the RELEASE LEVER ADJUSTING
to provide 1/64" CLEARANCE betweenstud SCREW to provide 1/64" CLEARANCE be-
of the L E F T HAND TRIP LEVER and the tween square stud of the NUMBER LATCH
stop pad of the LETTER LATCH LEVER. LEVERand the RIGHT HAND TRIP LEVER.

L E T T E R A N D NUMBER LATCH LEVER ADJUSTMENT

Verify that the LETTER and NUMBER LATCH LEVER ADJUSTING SCREWS a r e lnnse, then manually
or electrically actuate the LATCH SOLENOID.

A. Manuallyhold a letter buttonfully depress- B. Maintain the setting of Step A and tighten
ed, then adjust the LETTER LATCII LEVER the LETTER LATCH LEVER ADJUSTING
so that its stop tab rests lirmly against the SCREW. Check each letter button for pro-
square stud of thc L E F T HAND TRIP
LEVER. \ / per latching and selector switch contact
engagement.

LATCH SOLENOID
LETTERLATCH
LEVER
NUMBERLATCHLEVER
LETTERLATCH ADJUSTING SCREW
LEVER ADJUSTIN
SCREIV

NUMUERLATCH

C , Manually hold a number button fully de- \

pressed, then adjust the NUMBER LATCH D . Maintain the setting of Step C and tighten
LEVER so that the square stud of the NUM- the NUMBER LATCH LEVER ADJUSTING
BER LATCH LEVER rests firmly against SCREW. Check each number button for
the stop tab of the RIGHT HAND TRIP proper latching and selector switch con-
LEVER. tact engagement .
WURLITZER Page 38
SECTION B

FINAL LATCH SOLENOID ADJUSTMENT

A. Loosen the LATCII SOLENOID ADJUSTING B. Manually hold t h e LATCH SOLENOID

SCREWS. PLUNGER f i r m l y bottomed i n t h e LATCH
SOLENOID
LATCH SOLENOID
ADJUSTING SCREWS \
LATCH SOLENOID

RELEASE LEVER
STOP TAB
LATCH SOLENOID
PLUNGER

LEFT HAND
TRIP LEVER

C . Position the LATCH SOLENOID t o provide D . While manually holding the LATCH SOLE-
5/64" maximum clearance between the RE - NOID PLUNGER f i r m l y bottomed in t h e
LEASE LEVER STOP TAB and the L E F T LATCH SOLENOID, m a r k the LATCH
HAND TRIP LEVER. Tighten the LATCH SOLENOID PLUNGER with a n identifying
SOLENOID ADJUSTING SCREWS. m a r k a t the LATCH SOLENOID. Release
the LATCH SOLENOID PLUNGER, then
m e a s u r e and verlfy that the LATCH SOLE-
NOID PLUNGERtravel does not exceed3/16
of a n inch.

LATCH SOLENOIO SWITCH ADJUSTMENT

A. Loosen the LATCH SOLENOID SWITCH B. Manually hold the LATCH SOLENOID
ADJUSTING SCREWS. PLUNGER f i r m l y bottomed in the LATCH -
SOLENOID.
LATCH SOLENOID SWlTCH
.ADJUSTING SCRE\\'S -

LATCH SOLENOID LATCH SOLENOID

-
SWITCH
-
LATCH SOLENOID
PLUNGER -

,
D. Verify that t h e normally open contacts of C . Position the LATCH SOLENOID SWITCH t o -
the LATCH SOLENOID SWITCII close with provide 1/32" to 1/16" opening of t h e nor-
1/32 " overtravel. mally closed contacts. Tighten the LATCH
SOLENOID SWITCH ADTUSTING SCREWS. -
Page 48 WURLITZER
L E T T E R AND NUMBER SERIES SWITCH ADJUSTMENT
A. Loosen the LETTER and NUMBER SERIES B . Verify that the LATCH SOLENOID PLUNG-
SWITCH ADJUSTING SCREWS. ER is a t r e s t position.

LETTER SERIES SWITCH NUMBER SERIES SWITCH

ADJUSTING SCREWS ADJUSTING SCREWS

LETTER SERIES SWITCH

LATCH SOLENOID
LETTER LATCH LEVER PLUNGER

NUMBER LATCH LEVER NUMBER SERIES SWITCH

:s*:
C . Adjust the LETTERSERIES SWITCH s o that D . Adjust the NUMBERSERIES SWITCH s o that r<
.>q
:*>:
.......
.:.:.:.
....
the long blade of the switch r e s t s against the long blade of the switch rests against :i.....
::i
the insulated stud of t h e LETTER LATCH t h e insulated stud of the NUMBER LATCH
LEVER with z e r o clearance. Tighten the LEVER with z e r o clearance. Tighten the
LETTER SERIES SWITCH ADJUSTING NUMBER SERIES SWITCH ADJUSTING
SCREWS. SCREWS.

NOTE
When a letter and/or number button is latched, the contacts of their respective SERIES SWITCHES
should open 1/32" and should close with 1/32" overtravel when the button is released.

L E T T E R AND NUMBER L A T C H SWITCH ADJUSTMENT

A. Loosen t h e LETTER and NUMBER LATCH B. Manually hold t h e ,.JCH SOLENOID
PLUNGER f i r m l y bottomed in the LATCH
SWITCH ADJUSTING SCREWS.
\ SOLENOID.

LETTER LATCH SWITCH LATCH SOLENOID

ADJUS'IING SCREWS
LATCH SOLENOID
LETTER LATCH SWITCH PLUNGER

NUMBER LATCH SWI TCH

ADJUSTING SCREWS
......-

,
LEVER KIGHT HAND T I ~ I PLE\'EK \:NUMBER LALTCHSWITCH

C . Adjust the LETTER LATCH SWITCH s o that D. ~ d j u s t i h eNUMBER LATCH SWITCHso that
the long blade of the switch rests against the long blade of the switch rests against
tl1e insulated stud of the LEFT HAND TRIP the insulated stud of the RIGHT HAND TRIP
LEVER with z e r o clearance. Tighten LET- LEVER with z e r o clearance. Tighten the
T E R LATCH SWITCH ADJUSTINGSCREWS . NUMBER LATCH SWITCH ADJUSTING
SCREWS.

NOTE
T h e contacts of the LETTER and NUMBER LATCH SWITCHES a r e s e t normally open 1/32". When a
letter and/or number button is latched, the contacts of t h e i r respective switches should close with
1/32" overtravel

WURLITZER Page 56
SECTION B

-
Page 6B WURLITZER
 SECTION B

SELECTOR SWITCH ASSEMBLY ILLUSTRATED PARTS LIST

200
1 . Selector Button and Clip Assembly, A
Selector Button and Clip Assembly, B
Selector Button and Clip Assembly, C
Selector Button and Clip Assembly, D
Selector Button and Clip Assembly, E
Selector Button and Clip Assembly, F
Selector Button and Clip Assembly, G
Selector Button and Clip Assembly, H
Selector Button and Clip Assembly, J
Selector Button and Clip Assembly, K
Selector Button and Clip Assembly, L
Selector Button and Clip Assembly, M
Selector Button and Clip Assembly, N
Selector Button and Clip Assembly, P
Selector Button and Clip Assembly, Q
Selector Button and Clip Assembly, R
Selector Button and Clip Assembly, S
Selector Button and Clip Assembly, T
Selector Button and Clip Assembly, U
Selector Button and Clip Assembly, V
Cap Only
Clip Only
2. Button and Clip Assembly, Reset
3. Stop Bracket
Switch and Wire Assembly
Screw, 6-32 x 1/4 Hex. Sem. (2)
4. Selector Button and Clip Assembly, 1
Selector Button and Clip Assembly, 2
Selector Button and Clip Assembly, 3
Selector Button and Clip Assembly, 4
Selector Button and Clip Assembly, 5
Selector Button and Clip Assembly, t~
Selector Button and Clip Assembly, 7
Selector Button and Clip Assembly, 8
Selector Button and Clip Assembly, 9
Selector Button and Clip Assembly, 10
Cap Only
Clip Only
Complete Set Selector Button and Clip Assembly
5. Mounting Plate
6. Light Shield (2)
7. Light Diffuser
8. Light Diffuser
9. Selector Switch - Numbers
10. Electric Counter
Screw, 6-32 x 1/4 Hex. Sem . (2)
11. Receptacle - 9W
Contact (6)
12. Switch - Slide
- 13.
14.
Resistor -175 ohm -5W (2)
Crank and Link Assembly
Retaining Ring
- Retaining Ring

WURLITZER Page 7B
 SECTION B

ILLUSTRATED PARTS LIST CON'T -

ALL ALL
MODELS MODELS
15 . Latch Solenoid
Plunger, Solenoid
112104
112104-1
30. Stop Bracket 56628 -
Screw, 8-32 x 1/4 Hex. Sem. (2) 76902-34
Pin, Solenoid Plunger 65947 Washer (2) 27787
Washer 48 7 Rubber Grommet 117689 .=-.
Cotter Pin 23355 31. Cable Clamp (2) 73804-6
Screw, 6-32 x 3/16 Hex. Sem . 76902-21 Screw, 6-32 x 3/8 Hex. (2) 76901-68
16 . Mounting Bracket, Latch Solenoid 117747 32. Socket, Molex, 48 130019
Screw, 8-32 x 1/4 Hex. Sem. (2) 76902-34 Pin (46) 132200 -
Washer 54024 Pin (36)
17. Switch and Bracket Assembly, Latch, Numbers 126314 33 . Snap Bushing (2) 74849-10
Switch Assembly 60518 34. Connector Link (2) 3400-3460 126550
Retainer Plate 63014 Connector Link (2) 3410 12655.1 ,-

.....
.......
........
.........
..........
.
Screw, 3-48 x 5/8 R.H (2) 73503-18 Shoulder Bushing, Link (4) 124018
........::
.........
........... Mounting Bracket 121005 Spacer, Shoulder Bushing (2) 124040
...........
...........
........... Screw, 8 -32 x 1/4 Hex. Sem . (2)
..........
..........
.........
.......
........
......
76902-34
18. Switch and Bracket Assembly, Series, Numbers 111810
Screw, 6-32 x 3/8 Hex. Sem. (4)
35. Connector Link Plate (2)
76902-24
126521 -
Switch Assembly 64981 Spacer, Link, Selector Switch (4) 126299
Retainer Plate 63014 Screw, 8-32 x 5/8 Hex. Sem. (4) 76902-39
Screw, 3-48 x 3/8 R.H. (2)
Mounting Bracket
73503-15
111746
Washer
36. Shaft, Link and Lever Assembly
27787
126510
-
Screw, 8 -32 x 1/4 Hex. Sem . (2) 76902-34 37. Shaft, Link and Lever Assembly 126507
19. Switch and Bracket Assembly, Latch Solenoid 134396
Switch Assembly
Retainer Plate
134397
63014
38. Clamp
Screw, 8-32 x 5/16 Hex. Sem .
39. Selector Switch, Letters 3400-3460
76808-13
76902-35
133553
-
.
Screw, 3-48 x 1 R.H (2) 73503-157 Selector Switch, Letters 3410 133551
Mounting Bracket 125402
Screw, 8-32 x 1/4 Hex. Sem. 76902-34
Washer 73608-45
20. Latch Lever, Numbers 65009
Screw, 8-32 x 1/4 Hex. Sem . 76902-34
Washer 73608-45
21 . Trip Lever, Right Hand, Numbers 117694
Stop Nut, 10-32 74988-14
Washer (2) 76610
Washer 56773
Spring, Trip Lever, Right Hand 57129
22. Trip Lever, Left Hand, Letters 117691
Spacer 57790
Spring, Trip Lever, Left Hand 120067
23. Switch and Bracket Assembly, Series, Letters 66007
Switch Assembly 64982
Retainer Plate 63014
Screw, 3-48 x 7/16 R.H. (2) 73503-16
Mounting Bracket 64991
Screw, 8-32 x 1/4 Hex. Sem . (2) 76902-34
24. Switch and Bracket Assembly, Latch, Letters 126314
Switch Assembly 60518
Retainer Plate 63014
Screw, 3-48 x 5/8 R.H . (2) 73503-18
Mounting Bracket 121005
Screw, 8-32 x 1/4 Hex. Sem. (2) 76902-34
25. Release Lever 129102
Washer 56773
Spring, Solenoid Return 57130
26. Resistor, 85 ohm, 5W 74819-2
27. Resistor, 175 ohm, 5W 74824-2
28. Latch Lever, Letters 117695
Screw, 8-32 x 1/4 Hex. Sem. 76902-34
Washer 73608-45
29. Switch, L.P. Conversion 62886

Page 8B
 SECTION B

JUNCTION BOX ASSEMBLY ILLUSTRATED PARTS LIST

1. Printed Board Assembly 8 . Relay, White (4) 122123

2 . Cover and Label Assembly 9 . Socket and Paint Assembly (4) 123080
Screw, 6 x 5/8 Hex. Z (2) 10. Retainer, Socket (4) 122132
Spacer (2) .
11 Strain Relief 71878-16
Cover and Label Assembly 1 2 . Plug, 9, Red 131931
Cover and Label Assembly 13 .. Plug, 45 134046
Screw, 6 x 1 Hex. A (2) 14. Plug, 12, White 131175
Spacer (2) 1 5 . Plug, 15, White 131888
3 . Plug, 30 16. Socket, 12, Blue 134252
4 . Resistor 47 ohm Pin (10) 132000
- 5 . Capacitor 500 MFD 50V
6 . Capacitor 20 MFD 50V
17. Plug, 48
18. Plug, 45
130020
134046
7 . Rectifier
-
WURLITZER Page 9B
SECTION B

TOP TUNE UNIT AND MOUNTING BRACKET ASSEMBLY

-
1 Cover, Top Tunes 1 7 . Cable Clamp 73804-4
Screw, 6 x 1/4 Hex. Z (4) Screw, 8-32 x 1 / 4 Hex. Swage 74976-24
2. Plug, 9, White Washer 42120
Pin (4) 1 8 . Selector Switch 134738
3. Relay Screw, 6-32 x 7/8 Hex. Swage(2) 74976-29
.
Screw, 6-32 x 1/4 R .H Sem .(2) Spacer (2) 134746
4. Socket, Relay 1 9 . Resistor 85 o h m , 10% 5W 74819-2
5. Retainer, Socket 2 0 . Insulated Mounting Strip 24277
6. Button Screw, 6-32 x 1/4 Hex. Swage 74976-29
Insert, Button 21. Light Socket and Wire
Insert Assembly (2) 134812
7. Mounting Bracket Screw, 6-32 x 1/4 Hex. Swage(2) 74876-22
8. L a m p # 5 l (2) 22. Plug, 9 131174
9. Retaining Ring (2) Pin (6) 132000
10. Spring (2) 23. Plug, 3 0 134030
11. Mounting Plate and Plunger Pin (29) 132000
Assembly (2) Clamp (2) 654140
12. Insert Screw, 8 x 3/8 Hex. Z (2) 76626-13
13. Button 24. Socket, Relay, White (2) 131030
Insert, Button 2 5 . Retainer, Socket (2) 122132
14. Retainer, Button (4) 2 6 . Relay, White (2) 122133
15. Relay, White 2 7 . Chassis and Silk Screen A s s e m b l y 134027
16. Hold Down Spring Screw, 6 -32 x 1/4 Hex. Swage(4) 74976-34

Page 1 OB WURLITZER
 SECTION A

KEYBOARD - 160 Selection Phonographs

LP selections can be programmed in the 1 only o r 1 and 2 sections A thru V.
Minimum LP programming 10 LP records, 20 selections.
Maximum LP programming 20 LP records, 40 selections.
Automatic Programmer (when phonographs a r e s o equipped).
Gold Button selects records A7-C7-E7-G7-J7 and L7, also N7-Q7-S7-U7 if s o desired.
Red Button selects records A8-C8-E8-G8-J8 and L8, also N8-Q8-S8-U8 if s o desired.
The Automatic Programmer can be optionally set for six, eight or ten selections in the 1
-
and 2 sections .
.....
......
........
.........
..........
...........
.......... KEYBOARD - 100 Selection Phonographs
...........
..........
..........
........
.........
......
...... LP selections can be programmed in the A only or A and B sections 1 thru 0 .
Minimum LP programming 5 LP records, 10 selections.
Maximum LP programming 10 LP records, 20 selections.
SOUND SYSTEM
Solid State Amplifier. ...
Wurlitzer Model 550.
Pickup. .. .Astatic
Stylus. .. .Dual Tip Diamond .7 Mil
Power Output total. .. .80 watts music power .
Output Impedance. ...Multiple tap low impedance plus constant voltage.
CABINET SPEAKERS
2 - 12" low frequency speakers
2 - 6" mid-range speakers
2 - 3 x 5 high frequency speakers

STATESMAN ACCESSORIES

Remote Volume Control Kit 169B Part No.

Microphone Kit 198D Part No.
Stepper, 100 and 200 Selection, Model 265 Part No.
Stepper, 160 Selection, Model 266 Part No.
Income Computer, Model 207 Part No.
Wall Box, 200 Selection (with Speakers & Golden Bar), Model 5220 Part No.
Wall Box, 200 Selection (without Speakers or Golden Bar), Model 5220A Part No.
Wall Box, 100 Selection (with Speakers & Golden Bar), Model 5225 Part No.
Wall Box, 100 Selection (without Speakers or Golden Bar), Model 5225A Part No.
Wall Box Bar Mounting Bracket (Chrome), Kit 191 Part No.
Wall Box Bar Mounting Bracket (Aluminum), Kit 192 Part No.
Wall Box Mounting Plate, 5220-5225 Part No.
Wall Box Mounting Plate, 5220A-5225A Part No.
Wall Box Booster Transformer, Model 222B Part No.
Speaker, Extender, Model 5125B Part No.
Speaker, Directional, Model 5126 Part No.
Speaker, Wall, Model 5133 Part No.

Page C
 SECTION C

RECORD CHANGER ADJUSTMENTS

-
WURLITZER Page 1C
SECTION C

INDEX TO ADJUSTMENTS

Selection Accumulator Adjustment.......................................... Page 4C

Shaft and Magnet Arm Assembly Adjustment.. ............................... Page 4C
Override Assembly Adjustment. ............................................ Page 5C
Magazine Drive Motor Adjustment.. ........................................Page 5C
Magazine Lock Switch Adjustment. ......................................... Page 6C
Back Stop Pawl Adjustment.. ............................................... Page 6C
Side 1 Cancel Solenoid Adjustment.. ........................................ Page 7C
Side 1 and 2 Readout Switch Adjustment. .................................... Page 8 C
Safety Switch Adjustment. ................................................. Page 10 C
Bail and Bushing Assembly Clearance Adjustment. ........................... Page 10 C
-
Main Cam Motor Break Adjustment. ........................................ Page 10 C
Transfer Switch Adjustment. .............................................. Page 11 C
Cancel Switch Adjustment.. ............................................... Page 12 C
Record Takeout Arm Alignment.. .......................................... Page 12 C
Side 1 and 2 Shift Adjustment. ............................................. Page 13 C
Turn Arm Holdout Cam Adjustment.. ...................................... Page 14 C
Record Takeout Arm Turn Adjustment. .................................... Page 14 C
Record Takeout Arm Stop Adjustment. ..................................... Page 15 C
Turntable Drive Wheel Adjustment.. ....................................... Page 15 C
Turntable Speed Change Adjustment. ....................................... Page 16 C
Release Switch Adjustment.. .............................................. Page 17 C
Tone Arm Lift Adjustment.. .............................................. Page 17 C
Stylus Brush Adjustment .................................................. Page 17 C
Tone Arm Release Adjustment. ........................................... Page 18 C
Tone Arm Feed-In and Trip Switch Adjustment. ............................ Page 18 C
Play Switch Adjustment.. .................................:. .............. Page 19 C
Stylus Pressure Adjustment.. ............................................. Page 19 C
Turntable Pilot Reset Adjustment .......................................... Page 20 C
Override Cam Adjustment. ............................................... Page 21 C

-
Page 2C WURLITZER
 SECTION C

The center G I ~ L L L E
SCREEN and FRAME may be removed t o provide a c c e s s t o front of Record
Changer.

-. - ppppp -

RECORD CHANGER WITH GRILLESCREEN ANDFRAME REMOVED

The GRILLE SCREEN and FRAME i s removed a s follows:

A. unlock and r a i s e FRONT DOOR of Pl~ono B. RemovesixWWGNUTS.

graph.
/

WING NUT
(TYP.)

GRILLE
SCREEN
CATCHES

C. Release four IJKlLLIi SCREEN CLIPS. D. Remove GRILLE SCREEN and FRAME.

WURLITZER Page 3C
 SECTION C

SELECTION ACCUMULATOR ADJUSTMENTS

./ SELECTION ACCZJMULATOR

CONTACT PLATE and

DIRECTION OF ROTATION BLADE ASSEMBLY
/
MAGNETLAMINATION CONTACT PLATE and
MOUNTING SCREWS BLADE ASSEMBLY
MOUNTING SCREWS

SHAFT and MAGNET

ARM ASSEMBLY . .. . ?.,. ......- *./ SELECTOR LATCH PIN
~

SHAFT AND MAGNET ARM ASSEMBLY ADJUSTMENTS

A. Rotate SHAFT and MAGNET ARM AS- 8. If v e r t i c a l alignment cannot b e obtained,

..q SEMBLY in a clockwise direction and v e r - 1oosenMAGNET LAMINATION MOUNTING
a............s
.:$?.:~,,

+:.:::::? <
tically align the leading edge of the MAG- SCREW and align MAGNET LAMINATIONS
%
.....
:.:.:.:
.....
.,.,.. NET LAMINATIONS with the leading edgc t o meet requirement of Step A. Tighten
of SELECTOR LATCH PIN. MAGNET LAMINATION MOUNTING
\ SCREW.

NOTE: - ~ d b d b J ~1ks
k ~
..
~
=-".-
to clarify adjustment _._--~Z-L
k---
procedures only.

MAGNET LAMINATION
MOUNTING SCREW

C. Verify that OUTER CONTACT BLADE i s D. If requirement of Step C cannot b e obtained,

adjacent t o leading edge of thc OUTER loosen CONTACT PLATE and BLADE AS-
CONTACT PATCH with z e r o clearance. SEMBLY MOUNTING SCREWS and adjust
\ CONTACT PLATE and BLADE ASSEM-
BLY until t h e requircrnent of Step C is m e t .

CONTACT BOARD and

\ TightenCONTACT PLATE and BLADE AS-
SEMBLY MOUNTING SCREWS.

CONTACT PLATE and

CABLE ASSEMBLY BLADE ASSEMBLY

OUTER CON'I'AC'L' PA'I'CHES

OUTERCONTACTBLADE

Page 4C WURLITZER
 SECTION C

OVERRIDE ASSEMBLY ADJUSTMENTS

A. Verifythat both escapements of RATCHET B. LoosenRATCHET LEVERGUIDE ADJUST-
WHEEL and HUB ASSEMBLY arecancelled ING SCREWS and adjust RATCHET LEVER
off. LoosenOVERRIDE SWITCH ADJUST- GUIDEto allow RATCHET LEVERto r e s e t
ING SCREWS and adjust OVERRIDE one tooth while manually actuating OVER-
SWITCH t o provide a 1/32" opening be- RIDE LEVER ASSEMBLY. RATCHET
tween contacts. Tighten OVERRIDE LEVER must b e completely withdrawn
SWlTC!I-I ADJUSTING SCREWS. f r o m the tooth at t h e end of stroke. Tighten
RATCHET LEVER GUIDE ADJUSTING
SCREWS.
OVERRIDE SWITCH

-
RATCHET LEVER GUIDE
ADJUSTING SCREWS
ADJUSTING SCREWS
OVERRIDE SWITCH RATCHET LEVER GUIDE
RATCIIET LEVER
OVERRIDE [,EVER
ASSEMBLY ARMATURE and EYELET
ASSEMBLY
RATCHET WHEEL , MAGNET and BRACKET
E&*
*<.:\.:
.*.$$
and HUB @2.:
:<<.y
<.:...
ASSEMBLY ASSEMRLY
MAGNET and BRACKET
ASSEMBLY ADJUSTING
SCREWS
/
C. Loosen MAGNET and BRACKET ASSEMBLY ADJUSTING SCREWS and adjust MAGNET and BRACK-
ET ASSEMBLY f o r minimum gap that will allow ARMATURE and EYELET ASSEMBLY t o c l e a r
tooth by 1/32" without interference atPIVOT END of ARMATUREand EYELET ASSEMBLY. Tight-
e n MAGNET and BRACKET ASSEMBLY ADJUSTING SCREWS.

MAGAZINE DRIVE MOTOR ADJUSTMENT

A. Position Service Switch to OFF. Select B. Manually rotate RECORD MAGAZINE two
any convienient selectionfrom SELECTOR complete revolutions and check meshing
SWITCH, then manually cancel LATCH PIN of MAGAZINE DRIVE GEAR and RECORD
selected. MAGAZINE GEAR.

RECORD MAGAZINE

RECORD MAGAZINE GEAR

MAGAZINE DRIVE MOTOR
MOUNTING SCREWS
MAGAZINE DRIVE GEAR

C. Should adjustment be necessary, loosen MAGAZINE DKIVE MOTOR MOUNTING SCREWS and ad-
just motor a s rcquired t o satisfy requirements of Step B. Tighten MAGAZINE DRIVE MOTOR
MOUNTING SCREWS.

WURLITZER Page 5C
 SECTION C

MAGAZINE LOCK SWITCH ADJUSTMENT

A. Verify that LOCKING PIN of MAGAZINE B. With MAGAZINE LOCK SWITCH actuated,
LOCKING ARM is fully engaged with REC- c l e a r a n c e between MAGAZINE LOCK
ORD MAGAZINE PLATE as shown. SWITCH ACTUATOR and SWITCH BODY
should be 1/64".
RECORD MAGAZINE
PLATE
LOCKING PIN
MAGAZINE LOCK
SWITCH ACTIJATOR MAGAZINE LOCKING ARM

MAGAZINE LOCK
SWITCH MOUNTING 1/64" CLEARANCE
SCREWS

C. Should adjustment b e necessary, loosen

...* MAGAZINE LOCK SWITCH MOUNTING
4%
gi::*c
<.:.:.: .,.....
SCREWS and adjust MAGAZINE LOCK
..,..
..<.:,....
.,....
.,
.... .......
>*
:.,.,... SWITCH as r e q u i r e d t o satisiy requirement
..:...
..:.:.,.,
:j
of Step B.

BACK STOP PAWL ADJUSTMENT

A. Verify that LOCKING PIN of RECORD
MAGAZINE LOCKING ARM i s fully engaged
with RECORD MAGAZtNE PLATEas shown.

RECORD MAGAZINE LOCKING PIN

PLATE
<RECORD MAGAZINE

0. A clearance of 1/16" t o 3/32" should exist C. Should adjustment b e necessary, loosen

between t i p of BACK STOP PAWL and tooth BACK STOP PAWL MOUNTING SCREWS
of RECORD MAGAZINE PLATE at a depth ( f r o m underneath c h a s s i s plate) and adjust
of 1/16" t o 5/64" f r o m t i p o f toothas shown. BACK STOP PAWL as r e q u i r e d t o satisfy
requirement of Step B. TightenBACK STOP

\ PAWL MOUNTING SCREWS.

BACK STOP PAWL

-
1/16 3/32" CLEARANCE BACKSTOPPAWL
MOUNTING SCREWS

1/16 - 5/64" DEPTH

Page 6C WURLITZER
SIDE 1 CANCEL SOLENOID ADJUSTMENT

For the following adjustments it is recolnnlended that, depending on phonograph being adjusted, the
following selections be utilized:

Phonograph Model Recommended Selection

A. PositionSCAN-LOAD-RUN Switch to SCAN B. Verify that LOCKING PINof RECORD MAG-

and align recommended selcction directly AZINE LOCKING ARM is fully engaged
under Record Takeout Arm Assembly. with RECORD MAGAZINE PLATEas shown.

I
When selection is properly aligned, im-
mediately position SCAN - LOAD RUN -
Switch to LOAD.

RECORD hlAGAZINE LOCKING PIN

PLATE
RECORD MAGAZINE
LOCKING ARM

C. Manually release SELECTOR PIN which D. Verify that SIDE 1 CANCEL SOLENOID
corresponds to recommended record se- PLUNGER is directly centered over r e -
lection. , lcased SELECTOR PIN.

SIDE 1 CANCEL
SOLENOID PLUNGER

SELECTOR PIN (A-3 or

C-1 as required)

If the requirement of Step D cannot be satisfied, perform the following adjustment:

E. Carefully turn READOUT ARM ADJUSTING

SCREW a s required to satisfy requirement

WURLITZER Page 7C
SECTION C

SlDE 1AND 2 READOUT SWITCH ADJUSTMENTS

All selections referenced i n the following adjustment procedures must b e selected f r o m SELECTOR
SWITCH. Service Switch must b e in OFF position, SCAN-LOAD-RUN Switch must b e i n RUN position
and Record Changer must be "at r e s t " posltionduring entlre adjustment procedure. Access t o READ-
OUT SWITCHES i s accomplished by removing center GRILLE SCREEN and FRAME ASSEMBLY (Refer
t o Page 2C).

A. TurnSIDE 2 READOUTSWITCH ADJUSTING 13. T u r n SUIE 1READOUTSWITCH ADJUSTING

SCREW in a s necessary t o p o s i t ~ o n SIDE SCREW in a s necessary t o position SIDE 1
2 READOUT SWITCH ACTUATOR in a v e r - READOUT SWITCH ACTUATOR in a v e r -
t i c a l position a s shown. t i c a l position as shown.

SlDE 2 READOUT SWITCH

ADJUSTING SCREW

SlDE 1 READOUT SWITCH

ADJUSTING SCREW
SlDE 1 READOUT SWITCH
SIDE 2 READOUT SWITCH ACTUATOR
ACTUA'I'OR

C . Position Phonograph Line Switch to OFF, D. M.l;~nually

rotate RECORD MAGAZINE t o po-
then ON. Select D-l and D-2(L-2 and M-2 sition READOUT SWITCH ACTUATORS
on Model 3460). close to, but not touching, selected LATCH
PINS.

, SlDE 1 READOUT
S\VITCH ACTUATOR
SIDE 2 READOUT
SWITCH ACTUATOR
LATCH PINS

E. Bottom edge of ACTUATORS should b e 3/64" F . Ends of ACTUATORS should overlap edge of
to 5/64" below top of selected LATCH PINS. selected LATCH PINS 1/32" t o 1/16".

G. Should adjustment b e necessary to satisfy H. Manually cancel LATCH PINS. Position

requirements of Steps E a n d F , ACTUATORS Phonograph Line Switch t o OFF, then ON.
m a y b e refornled.

I. Manually rotate RECORD MAGAZINE topo- J. Rack out SIDE 1 and 2 READOUT SWITCH
sition SIDE 1 and 2 READOUT SWITCEl ADJUSTING SCREWS 2 1/2 t u r n s .
ACTUATORS 1/2" t o the right of LATCH
PIN A-1 .
Page 8C WURLITZER
- SECTION C !I

- K. Select A-3 (C-1 on Mode1 3460). Observe L. Verify that RECORD MAGAZINE is in po-
LOCKING PIN and slowly rotate RECORD sition t o play r e c o r d A-3 ( C - l on Model
MAGAZINE untilSIDE 1 READOUT SWITCM 3460).
- actuates, releasing LOCKING PIN which
shouldstrike tooth of RECORD MAGAZINE
PLATE1/4 OF TOOTH SLOPE LENGTH 1/4 OF TOOTH
- f r o m top of tooth. SLOPE LENGTH

- RECORD MAGAZINE
PLATE LOCKING PIN

-
LOCKlNPi ARM

-
- M. Should I adjustment b e necessary, adjust
SIDE 1 READOUT SWITCH ADJUSTING
N. Manually cancel LATCH PIN. Position
Phonograph Line Switch t o OFF, then ON.
$<:>,+<c:.,
+5(x.
....
: .....3
......-..
............
..:. :.,.,.
......?+.
SCREW as required t o satisfy requirements Repeat Steps K, L and M t o verify proper v.:;:..
.>....
- of Steps K and L. T u r n ADJUSTING SCREW
i n t o r e t a r d switch actuation and out t o ad-
operation of SIDE 1 READOUT SWITCH.

vance switch actuation.

P . Select A-4 (D-1 on Mode1 3460). Observe
- 0. Manually cancel LATCH PIN. Position
LOCKING PIN and slowly r o t a t e RECORD
MAGAZINE untilSIDE2 READOUT SWITCH
Phonograph Line Switch OFF, then ON.
actuates, releasing LOCKING PIN which
- Q. Verify that RECORD MAGAZINE is i n po- should s t r i k e tooth of RECORD MAGAZINE
PLATE 1 / 4 OF TOOTH SLOPE LENGTH
sition t o play r e c o r d A-4 (D-l on Model
3460). f r o m top of tooth.
-,
S. Manually cancel LATCH PIN. Position
R. Should adjustment b e necessary, adjust
Phonograph Line Switch OFF, then ON. Re-
SIDE 2 READOUT SWITCH ADJUSTING
- SCREW a s required t o satisfy requirement
.
of Steos P andQ T u r n ADTUSTING SCREW
peat Steps P, Q and R t o verify proper oper-
ation of SIDE 2 READOUT SWITCH.
in to r e t a r d s w i t c h actuation and out t o ad-
- vancc switch actuation. U. Should adjustment b e necessary, loosen
MOUNTING SCREW andadjust PRETRAVEL
T. Check position of SIDE 1 and 2 READOUT ADJUSTMENT BRACKET as required t o

- SWITCH ACTUATORS. ACTUATORS must

not come t o rest over a LATCH PIN.
provide additional pretravel.
MOUNTING SCREW.
Tighten

- MOUNTING SCREW

PRETRAVEL ADJUSTMENT
- SIDE 2 READOUT
BRACKET
SWITCH ACTUATOR

-
SECTION C

SAFETY SWITCH ADJUSTMENT

A. With Record Changer "at rest" position, B. Should adjustment b e necessary, loosen
manually bottom SAFETY SWITCI-I ACTU- SAFETY SWITCH ADJUSTING SCREWS and
ATOR against switch body. T h e r e should adjust SAFETY SWITCH as r e q u i r e d t o
be 3/32'' CLEARANCE between SAFETY satisfy requirement of Step A. Tighten
SWITCH ACTUATOR and RECORD CLAMP SAFETY SWITCH ADTUSTING SCREWS.
ROLL PIN.

3/32" CLEARANCE
RECORD C L I ~ ~ PIN
IP
SAFETY S\\'lTCH
SAFETY SI\'ITCH
ACTUATOR

SAFETY S\\'I'l'CII
ADJUSTING SCREWS

BAIL AND BUSHING ASSEMBLY CLEARANCE ADJUSTMENT

A. With RECORD TAKEOUT ARM at "rest" B. Should adjustment b e necessary, loosen

position, t h e r e should b e .005" END PLAY ALLEN SCREWS on e i t h e r s i d e of BAIL
between BAIL AND BUSHING ASSEMBLY AND BUSHING ASSEMBLY andadjust 100s-
and GEAR PLATE AND PIN ASSEMBLIES. e n c d s i d e t o satisfy requirementof Step A.
Tighten ALLEN SCREWS.

.DO? END PLAY GEARPLATE AND

PIN ASSEMBLY
GAIL AND GUSHING
ASSEMGLY

GEAR PLATF: AND ALLEN SCREWS

PIN ASSEbICLY

MAlN CAM MOTOR BRAKE ADJUSTMENT

P r i o r to making the following adjustment, verify that Record Changer i s "at rest" position, then po-
sition Service Switch t o OFl:.
A. Manually actuate MAIN CAM MOTOR B. Should adjustment b e necessary, loosen
BRAKE SOLENOID PLUNGER. There SOLENOID MOUNTING SCREWS, then
should b e 1/64" CLEARANCE between while manually actuating MAIN CAM MO-
LEVER and PAD ASSEMBLY and BRAKE
- ~ TOR BRAICE SOLENOID PLUNGER., adiust
WIIEEL. MAIN CAM MOTOR BRAKE SOLENOID
1/64" CLEARANCE as required t o satisfy requirement of Step
A. Tighten SOLENOID MOUNTING
LEVER and PAD SCREWS.
I~SSEMBLY
BRAKEWHEEL
MAlN CAM MOTOR
BRAKE SOLENOID
PLUNGER
SOLENOID MOUNTN'G
MAlN CAM MOTOR SCREWS
BRAKE SOLENOID
TRANSFER SWITCH ADJUSTMEMY
Verify that a r e c o r d i s in "play" position. Cancel r e c o r d and immediately upon r e c o r d entering
RECORD MAGAZINE, position Service Switch to O F F .

A. Position S e r v ~ c eSwitch t o ON and cycle

CAM and GEAR ASSEMBLY until RECORD ,RECORDCLAMP
CLAMP CAM FOLLOWER reaches the peak CAMFOLLOWER
of RECORD CLAMP CAM LORE a s shown,
then position Service Switch to O F F .
,RECORDCLAMP
CAM LOBE

B. Manually p o s ~ t i o n TRANSFER SWITCH C . Should adjustment b e necessary, loosen

ACTUATOR as shown. T h e r e should be TRANSFER SWITCH MOUNTING SCREWS
1/16" CLEARANCE be'nveen tip of TRANS- and adjustTRANSFER SWITCH as required
F E R SWITCH ACTUATORand MAIN GEAR t o satisfy requirement of Step B. Tighten
TRACK LOBE. / TRANSFER SWITCH MOUNTING SCREWS.

TRANSFER SWITCH
MOUNTING SCREWS

1/16" CLEARANCE
TRANSFER SWITCH
ACTUATOR MAIN GEAR
TRACK LOBE

D. Position Service Switch t n ON and cycle E . Manually bottom TRANSFER SWITCH

ACTUATOR against switch body. T h e r e
CAM and GEAR ASSEMBLY until TRANS-
F E R SWITCH ACTUATOR is 1-iding on should b e 1/32" CLEARANCE between
MAIN GEAR TRACK as shown, then po- TRANSFER SWITCH ACTUATORand MAIN
sition Service Switch t o O F F . GEAR TRACK.

TRANSFER SWITCH
ACTUATOR

MAIN GEAR TRACK

1/32" CLEARANCE

F. Should adjustment he necessdqi, looszn G . r o s ~ t i o n Service Switch to ON and cycle

SWITCH BRACKET MOUNTING SCREWS, CAM and GEAR ASSEMBI.lr . Verify that
making s u r e that horizontal positioning i s each t i m e TRANSFER SWITCH ACTUATOR
maintained, then adjust SWITCH BRACK- falls into r e c e s s of MAIN GEAR TRACK,
ET a s required to satisfy requirenlent of switch actuates.
Step E. Tighten SWITCH BRACKET
MOUNTING SCREWS.

WURLITZER Page 1 1 C
SECTION C

CANCEL SWITCH ADJUSTMENT

Prior to making the following adjustment, position SERVICE SWITC1-l t o O F F and verify that SCAN-
LOAD-RUN SWITCH i s in RUN position. Make a r e c o r d selection.

A. Utilizing Service Switch cycle CAM and B. Should adjustment b e necessary, loosen
GEAR ASSEMBLY until TRACK CAM CANCEL SWITCH ADTUSTING SCREW and
GROOV-PIN i s on the peak of CANCEL adjust CANCEL SWITCI-I t o satisfy the r e -
SWITCH ACTUATOR. Verify that CANCEL qulrelnent of Step A .
SWITCH h a s actuated with 1/32" t o 3/64"
overtravel.

TRACK CAM GROOV-PIN

CANCEL SWITCH
ACTUATOR

CANCEL SIVITCH

CANCEL SIVITCH
ADJUSTING SCREW

RECOROTAKEOUT ARM ALIGNMENT

A. Select a r e c o r d that i s known to be flat. B. Should a d j u s t ~ n c n t b e necessary, loosen
UtilizingSERVICE SWITCH, stop RECORD LOCI< NUTand adjust RECORD TAKEOUT
TAKEOUT ARM when STOP PINS of GEAR ARM ADJUSTMENT SCREW a s r e q u i r e d t o
and PLATE ASSEMBLIES a r e approxi- satisfy the requirement of Stcp A. Tighten
matcly 1/4" f r o m RECORD TURN STOP LOCK NUT.
ASSEMBLIES. Verify that the r e c o r d is
centered between RECORD SEPARATORS /

RECORD TAKEOUT ARM

RECORD SEPARATORS

STOP PINS

RECORD TAKEOUT 4RM

ADJUSTMENT SCREW
, RIXORD TURN STOP
ASSEMBLY
RECORDTURNSTOP
ASSEMGLY LOCK NUT -
WURLITZER
 SECTION C

SIDE 1AND 2 SHIFT ADJUSTMENTS

A. Position Service Switch to OFF. Loosen B. Select A-3 (C-1 on Model 3460). Position
SOLENOID PLUNGER LINK ASSEMBLY Service Switch t o O F F t o stop Record
ADJUSTING SCREWS. Position Service Changer when STOP PINS of GEAR and
Switch t o ON. PLATE ASSEMBLIES a r e 1/4" f r o m REC-
ORD TURN ARMS as shown. Flange of
SOLENOID SIDE 1 RECORD TURN ARM should b e
PLUNGER centered between inner s i d e of head of STOP
LINK ASSEMBLY

SHIFT SOLENOID
GEAR and PLATE
SHIFT SOLENOID ASSEMBLIES
ADJUSTING SCREWS

C. Should adjustment b e necessary, loosen

SHIFT SOLENOID ADJUSTING SCREWS
and adjust energized SHIFT SOLENOID a s
required t o satisfy requirement of Step B.
Tighten SHIFT SOLENOID ADJUSTING
SCREWS,

D. Position Service Switch t o ON and cancel

r e c o r d . Select A-4 (D-1 on Mode1 3460).
PositionServiceSwitch to O F F t o stop Rec- SIDE 1 RECORD SIDE 2 RECORD
o r d Cbaneer when STOP PINS of GEAR TURN ARM TURN ARM
and PLATE ASSEMBLIES a r e 1/4" f r o m E. Should adjustment b e necessary, adjust
RECORD TURN ARMS a s shown. T h e r e SIDE 1 SOLENOID STOP ADJUSTmG
should b e 5/64" to 7/64" between head of SCREW a s required t o satisfy requirement
STOP PIN and SIDE 1 RECORD TURN ARM. of Step D.

GEAR and PLATE

ASSEMBLIES

SIDE 1 SOLENOID STOP

ADJUSTING SCREW . STOP PINS
SIDE 1 RECORD , SIDE 2 RECORD
TURN ARM TURN ARM
5/64" to 7/64" CLEARANCE ' 1/16" CLEARANCE

F. Adjust SOLENOID PLUNGER LINK AS-

SEMBLY t o provide 1/16" CLEARANCE
between flange of SIDE 2 RECORD ARM
TURN and inner s i d e of head of STOP PIN as
shown. Tighten SOLENOID PLUNGER
/
LINK ASSEMBLY ADJUSTING SCREWS.

WURLITZER Page 13C

TURN ARMHOLDOUTCAMADJUSTMENT
A. With Record Changer "at r e s t " position, 8. Siould adjustment b e necessary, loosen
flat surface of LOCKOUT CAM should b e SET SCREWS and adjust LOCKOUT CAM
v e r t i c a l t o RECORD CHANGER MOUNTING as r e q u i r e d t o satisfy requirement of Step A.
PLATE as shown. \ / Tighten SET SCREWS.

SET SCREWS

LOCKOUTCAM

RECORD CHANGER
MOUNTING PLATE

C. Loosen S E T SCREW located on top of LOCK- D. Should adjustment be necessary, loosen re-
OUT CAM. Select A-3 (C-1 on Model 3460). maining SET SCREW and adjust LOCKOUT
Position Service Switch l o O F F a s RECORD CAM as required t o satisfy requirement of
TAKEOUT ARM starts t o t u r n . LOCKOUT
CAM should make contact wit11 SIDE 1 TURN
.
Step C Tighten SET SCREW. When Rec-
o r d Changer returns to "at rest" position,
ARM as shown. \ repeat Steps A and B.

Select A-3, (C-1 on Model 3460). Position Service Switch t o O F F when selected r e c o r d is i n "play"
position.

A. RECORD TAKEOUT ARM should b e paral- B. Sliould adjustment b e necessary, adjust

l e l t o top of TURNTABLE. SIDE 1RECORD ARM TURN ADJUSTMENT
SCREW as required t o satisfy requirement
of Step A.
SIDE 2 RECORD TAKEOUT
ARM ADJUSTMENT SCREW
RECOKDTAKEOUTARM

SIDE 1 RECORD TAKEOUT TURNTABLE

ARM ADJUSTMENT SCREW

Select A-4 (D-1 on Model 3460). Position Service Switch to O F F whcn selected r e c o r d is i n "play" po-
sition. Repeat Steps A and B using SIDE 2 RECORD ARM TURN ADJUSTMENT SCREW.

Page 14C
 SECTION C

RECORD TAKEOUT ARM STOP ADJUSTMENT

F o r the following adjustment Record Changer must h e in "at r e s t " position.

A. Position a straight edge onTURNTADLE a s R. Adjust RECORD TAKEOKC ARM STOP AD-
shown. T h e r e should be 1/16" CLEAR- JUSTMENT SCREW a s required t o satisfy
ANCE between straight edge and head of requirement of Step A.
RECORD TAKEOUT ARM STOP ADJUST-
MENT SCREW.

=.:.
.: :~:.:.:
...........<
,xe..;.:.
TURNTABLE DRIVEWHEEL ADJUSTMENT .:.....
:c<<..:.:.:.
....
.:..<..::..
~

,..
Make t h e following adjustment with the RECORD CHANGER "at r e s t " position.

A. V e r m that the clearance between TURN- B. Should adjustment b e required, loosen

TABLE DRIVE WHEEL and TURNTABLE TURNTABLE DRIVE WHEEL ADJUSTING
MOTORSLEEVEis 1/16"t0 1 / 8 " as shown. SCREWS and adjust TURNTABLE DRIVE
WHEELADJUSTMENTPLATEas necessary

\ t o m e e t t h e requirement of Step A. Tighten

TURNTABLE DRIVE WHEEL ADJUSTING
SCREWS.

TURNTABLE DRIVE WHEEL

ADJUSTMENT PLATE

TURNTABLE DRIVE WHEEL

ADJUSTING SCREWS

TURNTABLE DRIVE WHEEL

TURNTAULE: MOTOR
SLEEVE
\
1 / 1 6 V o 1/S" CLEARANCE

WURLITZER Page 15C

 SECTION C

TURNTABLESPEED CHANGE ADJUSTMENTS

A. Select a 33 1/3 R. P. M. r e c o r d . As r e c - B. Should adjustment be necessary, loosen
o r d i s positioned on TURNTABLE, TURN- TURNTARLE SPEED CHANGE SWITCH
TABLE SPEED CHANGE SWITCH should MOUNTING SCKlSWS and adjust TURN-
actuate wit11 1/32" t o 1/16" overtravel of TABLE SPEED CHANGE SWITCH as re-
ACTUATOR. quired to satisfy requirement of Step A .
Tighten TURNTAULE SPEED CHANGE
SWITCH MOUNTING SCREWS.

TURNTABLE SPEED
CHANGE SIYITCH 1/32" to 1/16"

TURNTABLE SPEED
CHANCE SWITCH
MOUNTING SCREII'S

.*$i
,a$$,: C. Manually actuate TURNTABLE SPEED D. TURNTABLE DRIVE WHEEL should lift
..:,.:
....... .....
.,.....
........,.,
.:.:.:.:
..:.:
>*: .
.,.,.,., CHANGE SOLENOID PLUNGER. 1/4".
.,....
......
.....
..,.,.,.
... \

TURNTABLE
SPEEDCHANGE
I
SOLENOID 3
TURNTABLE
DRIVE
\VIIEEL

E. Should adjustment be necessary, cancel F. Verify that TURNTABLE PILOT is still i n

r e c o r d and manually collapse TURNTABLE 33 1/3 R. P. M . position. ReinstallTURN-
PILOT to 33 1/3 R. P. M. position. Re- TABLE, TURNTABLE RING and TURN-
move TURNTABLE MOUNTING SCREWS, T M L E MOUNTING SCREWS. Tighten
TURiVTABLE RING and TURiVTABLE. TURNTABLE MOUNTING SCREWS a n d v e r -
Loosen TURNTABLE SPEED CHANGE ify proper operation of TURNTABLE PILOT.
SO1,ENOID MOUNTING SCREWS and a d -
just TURNTABLE SPEED C!IANGE SOLE-
NOID as required t o satisfy s a l ~ a requirement
rS~C ( U I I C I I I C L I L
~

of Step D. Tighten
T ~ g h t c nTURNTABLE SPEED
CHANGE SOLENOID MOUNTING SCREI SCREWS.
TURNTABLE
PILOT

TURNTABLE
SPEED CHANGE
SOLENOID
MOUNTING SCREWS

Page 16C WURLITZER

 SECTION C

RELEASE SWITCH ADJUSTMENT

Select A-2 (B-1 on Mode1 3460). Position Service Switch t o O F F when selected r e c o r d i s i n "play"
position.
A. With STOP PIN against SIDE 2 RE1,EASE B. Should adjustment be necessary, loosen
SWITCH ACTUATOR, RELEASE SWITCH SWITCH BRACKET ADJUSTING SCREWS
shouldachmte with 1/64"to 1/32" CLEAR- and adjust RELEASE SWITCH as required
ANCE between RELEASE SWITCII ACTU- to satisfy requirement of Step A. Tighten
ATOR and switch body. SWITCH BRACKET ADJUSTING SCREWS
and position Service Switch t o ON.

RELEASE SWITCH
, RELEASE SWIITCH
ACTUATOR
SWITCH BRACKET

- STOP PIN
SWITCH BRACKET
ADJUSTING SCREWS

.
Select A-1 Position Service Switch t o OFF when selected record is in "play"position. Repeat Steps
A and B t o adjust SIDE 1 RELEASE SWITCH.

TONE ARM LIFT ADJUSTMENT

A. With Record Changer a t "rest" position, B. Should adjustment be necessary, adjust
the top of TONE ARM should be parallel TONE ARM LIFT ADJUSTING SCREW as
with ton of TURNTABLE. reauired t o satisfv reauirement of Sten A.

PARALLEL TONE ARM

TURNTABLE

TONE ARM LIFT

ADJUSTING SCRE\V
STYLUS BRUSH ADJUSTMENT
A. STYLUS BRUSH should be p o s ~ t ~ o n e dt o B. Should adjustment be necessary, loosen
provide 1/32" PENETRATION of STYLUS STYLUS BRUSH HOLDER MOUNTING
tnto the bristles of STYLUS BRUSH a s TONE SCREW and adjust STYLUS BRUSH HOLDER
ARM passes over STYLUS BRUSI I . as requlred t o satisfy requirement of Step
A. Ti&ten STYLUS BRUSH HOLDER
MOUNTING SCREW.

1/32" PENETRATION

STYLUS BRUSH
STYLUS BRUSH HOLDER
STY1,US BRUSH HOLDER MOUNTING SCREW

WI I Q I IT7FR Pose 17C

 TONE ARM RELEASE ADJUSTMENT
A. Make a rccord selection. Position Service B. T h e r e should b e ZERO CLEARANCE (no
Switch to OFF t o stop Record Changer play) between ADJUSTMENT LEVER and
whenTONE ARM h a s started down on rec- BUSHING ASSEMBLY, LEVER and BUSH-
ord, but prior t o TONE ARM touching r e c - ING ASSEMBLY and PIVOT ARM and PIN
ord. ASSEMBLY.

TONE ARM
PIVOT ARM and..
PIN ASSEMELY
ZEROCLEARANCE
LEVER and GUSHING
ASSEMDLY

TONE ARM RELEASE ADJUSTMENT LEVER and

ADJUSTING SCREW BUSHING ASSEMBLY

,...
C. T h e r e should be ZERO CLEARANCE be- \ D. Should adjustment b e necessarg, adjust
,;<;;K
tween ADJUSTMENT LEVER and BUSHING TONE ARM RELEASE ADJUSTING SCREW
.,........,................
...................... ASSEMBLY andTONE ARM RELEASE AD- as required t o satisfy requirements of
.
~

......
,:,:..::,.. ::.::........
:. ...
.:.....
....
::::: JUSTING SCREW. Steps B and C

-
TONE ARM FEED IN AND TRlP SWITCH ADJUSTMENTS
A. Make a record selection. Position Service B. Should adjustment b e necessary, adjust
Switch t o OFF t o stop Record Changer TONE ARM FEED-IN ADJUSTING SCREW
when TONE ARM h a s started down on rec- as requiredto satisfy requirement of Step A.
ord but p r i o r t o TONE ARM touching rec-
o r d . TONE ARM STYLUS should be
3 11/32" from tip of TURNTABLE PILOT.

TRIP S\I'ITCH
\ TONE ARM
FEED-IN
ADJUSTING SCREW

3 11/32" .4DJUSL'ING
DIMENSION SCRE\I1

TONE
* ARM STOP
BRACKET
AUJUYl'I\G
SCKEH
2 3/32"
TONE ARM

I
DIMENSION '
TRlP SWITCH
STYLUS
STOP BRACKET

C. Position Service Switch to ON t o play r e c - D. Should adjustment be necessary, adjust

o r d . TRIP SWITCH should actuate when TRIP SWITCH ADJUSTING SCREW a s re-
TONEARM STYLUS is 2 3/32" f r o m tip of quired t o satisfy requirement of Step C.
TURNTABLE PILOT.

E . With Record Changer in "at r e s t " position, F. Should adjustment be necessary, loosen
manually actuate TRIP SWITCH ACTU- STOP BRACKET ADJUSTING SCREW and
ATOR. Slowly r e l e a s e ACTUATOR. When adjust STOP BRACICET a s required to s a t -
TRIP SWITCII resets, ACTUATOR should .
isfy requirements of Step E Tighten STOP
be 3/32" t o 1/8" from TRIP SWITCH STOP BRACKET ADJUSTING SCREW.
BRACKET.

Page 18C WURLITZER

 SECTION C

PLAY SWITCH ADJUSTMENT

Make the following adjustment with the Record Changer in "rest" position.

A. Verify that 1/16" CLEARANCE exists be- B. Should adjustment be required, t u r n AD-
tween PLAY SWITCH ACTUATOR and AD- JUSTMENT LEVER ACTUATOR ADJUST-
JUSTMENT LEVER ACTUATOR. ING SCREWas necessaryto satisfy the r e -
\ quirement of Step A.

ADJUSTMENT LEVER

1/16" CLEARANCE ADJUSTMENT LEVER

ACTUATOR ADJUSTING SCREW
&3
STYLUS PRESSURE ADJUSTMENT .8%
.....
........::
.:.:.:.:.:~:
g,::
.:~:...
A. With a record on the turntable and TONE B. Stylus should break contact with record at
ARM in playing position, apply GRAM 5 t o 6 Grams of upward p r e s s u r e as ind'i-
PRESSUREGAUGE 3/8"from end of TONE cated on GRAM PRESSURE GAUGE. Should
ARM as shown. \ adj.ustmentbe required, proceed t o s t e p C .

C. To adjust STYLUS pressure, rotate STY-

LUS PRESSURE ADJUSTMENT WEIGHTas
necessary t o satisfy the requirement Step B.

STYLUS PRESSURE
ADJUSTMENT \VEIGH

WURLITZER Page 19C

 SECTION C

TURNTABLE PILOT RESET ADJUSTMENT

A. Select a 33 1/3 R. P . M. record. Cancel B. There should he 1/32" to 3/64" CLEAR-

record when it is in "play" position. Using ANCE between PILOT LATCH LEVERS
Service Switch, stop Record Changer when and TURNTABLE RING a s shown.
TURNTABLE PILOT has been l i e d to maxi-
mum height.

'IUKNTAULE
KING
TURNTABLE
P1Lo.r LEVEKS S1 1/32" to 3/64"
CLEARANCE

i&*
x@ C. Should adjustment be necessary, adjust D. Position Service Switch to ON, then select
*.,......
.:.:.::.::.:.:
.,......* % TURNTABLE PILOT LIFT ADJUSTING a 33 1/3 R. P. M. record. With selected
.:;:;??;
....,..:.~ SCREW a s required to satisfy requirement record in "play" position, verify that there
of Step B. is VISUAL CLEARANCE between TURN-
TABLE RESET LEVERandHUB ASSEMBLY
and PILOT TUBE WASHER.

PILOT TUBE WASHER

VISUAL CLEARANCE TURNTABLE RESET LEVER and

HUB ASSEMBLY

TURNTABLE PILOT LIFT

ADJUSTING SCREW

Page 20C WURLITZER

 SECTION C

OVERRIDE CAM ADJUSTMENT

All selections referenced in the following adjustment procedure m u s t b e sclected f r o m SELECTOR
SWITCH. Service Switch must b e in OFF position, SCAN-LOAD-RUN Switch m u s t b e in RUN position
and Record Changer must be "at r e s t " positionduringentire adjustment procedure. Access t o OVER-
RIDE CAM is accomplished by removing C r o s s Rail f r o m r e a r of Phonograph Cabinet.

A. Select K-1 (A-5 on Model 3460). Manually B. Manually rotate RECORD MAGAZINE until
cancel selected LATCH PLN. OVERRIDE CAM p a s s e s OVERRIDE LEV-
ER ASSEMBLY PIN. RATCHET WHEEL
andHUB ASSEMBLY should reset one tooth.
If r e s e t did not occur, proceed t o Step C.
PIN If r e s e t did occur, proceed t o Step D.

OVERRIDE CAM.

OVERRIDE LEVER. RAI'CIIE?' WHEEL and

ASSEMBLY HUB ASSEMBLY

C . Position Phonograph t o OFF. Loosen Hex

Head OVERRIDE CAM MOUNTING SCREW
D . Manually rotate RECORD MAGAZINE until
OVERRIDE CAM approaches OVERRIDE
andmove OVERRIDE CAM slightly outward LEVER ASSEMBLY PIN f o r second timc.
t o i n c r e a s e c a m overthrow. TightenOVER- F r o m front of Record Changer, observe
RIDE CAM MOUNTING SCREW. Position LOCKING ARMand slowly rotate RECORD
Phonograph Line Switch t o ON. MAGAZINE until OVERRIDE LEVER AS-
SEMBLY actuates, releasing LOCKING
PIN which should s t r i k e tooth of RECORD
MAGAZINE PLATE1/4 OF TOOTH SLOPE
LENGTH f r o m top of tooth.
OVERRIDE OVERRIDE CAM
CAM MOUNTING SCREW \
RECORD
MAGAZINE \

1/4 OF TOOTH
SLOPE LENGTH

WURLITZER Page 21C

SECTION C

E. Verify that RECORD MAGAZINE is in po- F. Should adjushnent b e necessary, adjust

.
sition to play record A-l OVERRIDE CAM ADJUSTING SCREW a s
required to satisfy requirements of Steps
D and E .

OVERRIDE CAM

OVERRIDE CAM
ADJUSTING SCREW

*..
NOTES

Page 22C
 SECTION C

INDEX T O PARTS DRAWINGS

Selection Accumulator................................. Page 24 .25C

Record Changer L. H . ................................ Page 26 - 27C
Record Magazine Assembly.. ........................... Page 2 8C
Record Takeout Arm.. ................................. Page 29C
Cam and Gear Assembly. .....................me..e.....
Page 30 .31C
Turntable Assembly ....................................Page 32C
Tone Arm Assembly., ................................. Page 33C
Turntable and Mounting Plate Assembly. ................. Page 34 - 35C
Recordchanger R.H. .................................. Page 36 - 37C

WURLITZER Page 23C

SECTION C

Page 24C WURLITZER

 SECTION C

SELECTION ACCUMULATOR ILLUSTRATED PARTS LIST

1. L a t c h P i n - I n s i d e 128321
2, L a t c h P i n - O u t s i d e 128320
S p r i n g - L a t c h Pin-Selection
Accumulator 128322
3. R i n g and S p a c e r A s s e m b l y 3400 133532
R i n g and S p a c e r A s s e m b l y 3410 134082
Ring and S p a c e r A s s e m b l y 3460 134245
S c r e w , 8-32 x 5 / 1 6 Rd.
S e m s (4) 73533-35
S c r e w , 8-32 x 1-118 Rd.
S e m s (8) 73533-43
S p a c e r (8) 128324
4. P l a t e - P i n S t o p 133348
5. Shaft and Magnet A r m A s s e m b l y -
Selection Accumulator 133499
6. Bobbin and W i r e A s s e m b l y (2) 133375
7. Contact P l a t e and B l a d e A s s e m b l y 133447
S c r e w , 8-32 x 1 R d . Hd. S e m s 73533-42
S c r e w , 6-32 x 7 / 1 6 Rd. Hd.
S e m s (2) 73533-25
8. T h r u s t W a s h e r (2) 122630
9. B a l l R a c e 12263 1
10. S p a c e r - S e l e c t i o n A c c u m u l a t o r 133886 .
11. Contact B o a r d and C a b l e
Assembly 3400 133709
Contact B o a r d and C a b l e
Assembly 3460 134273
Contact B o a r d and C a b l e
Assembly 3410 134122
S c r e w , 8-32 x 5 / 1 6 Rd. S e m s 73533-35
W a s h e r (8) 51822
P l u g - 45 134045
Pin 132000
12. C a s t i n g and Bushing A s s e m b l y -
Selection Accumulator 133531
Clutch and B e a r i n g A s s e m b l y 128638
13. S p r i n g W a s h e r 128739
14. G e a r and Hub A s s e m b l y -
S e l e c t i o n A c c u m u l a t o r -Shaft 128305
S e t S c r e w , 8-32 x 118 F1. 73513-28
15. Motor Mounting P l a t e -
Selection Accumulator 128291
S c r e w , 8-32 x 5 / 1 6 Rd. S e m s 73533-35
16. M o t o r and G e a r A s s e m b l y 135136
S c r e w , 8-32 x 5 / 1 6 Rd. S e m s 73533-35
G e a r and Hub A s s e m b l y 128293
Roll P i n 73782-34
17. S u p p o r t L e g , S e l e c t i o n
A c c u m u l a t o r ( F o r S e r v i c e Only) 133420
18. Contact P l a t e and B l a d e A s s e m b l y 133446
S c r e w , 8-32 x 1 Rd. Hd. S e m s 73533-42
S c r e w , 6-32 x 7 / 1 6 Rd. Hd.
S e m s (2) 73533-25
19. C a p a c i t o r , . 18 mfd. 75V (2) 76201-17
20. Diode - Z e n e r (2) 128449

Page 25C
 SECTION C

RECORD CHANGER ILLUSTRATED PARTS LIST, L. H .

1. D r i v e A r m A s s e m b l y , M a g a z i n e 133466 33. R e a d o u t A r m s w i t c h (2) 133448
( P a r t of D r i v e A r m and S u p p o r t 34. B r a c k e t , P r e t r a v e l (2) 133389
A s s e m b l y , 133504) 35. B r a c k e t A s s e m b l y , R e a d o u t (2) 133475
2. Housing, B e a r i n g , M a g a z i n e s h a f t 128384 36. Actuator L e v e r , Outside 133392
3. B a c k s t o p P a w l A s s e m b l y 122084 Actuator L e v e r , Inside 133391
Spring 59710 W a s h e r (2) 53519
Bumper 54246 S p r i n g g r i p F a s t e n e r (2) 76896-9
4. P l u n g e r , C o u n t e r W h e e l A c t u a t o r 133951 37. Spring, Readout Switch (2) 133426
5. Bracket, Plunger 133950 38. S u p p o r t A r m a n d S t o p Nut A s s e m b l y 133465
6. S p r i n g , P l u n g e r 134000 ( P a r t of D r i v e A r m a n d S u p p o r t
7. Cup W a s h e r 124530 A r m A s s e m b l y , 133504)
8. R e t a i n i n g R i n g 73724-25 39. R e a d o u t A r m and S u p p o r t A s s e m b l y 133997
9. C o u n t e r L e v e r and Shaft A s s e m b l y 133952 40. Override Cam 133461
10. B e a r i n g B r a c k e t and B u s h i n g 41. Contact Assembly, Readout A r m 133432
Assembly 133959 42. Shaft, Drive A r m 133385
11. P l a t e and S i l k S c r e e n A s s e m b l y 134888 43. Positioning P l a t e , Magazine Lock
12. M i r r o r , R e c o r d P l a y i n g 134891 Bracket 135212
13. L a m p 56763 44. S p r i n g , R a t c h e t Wheel,
14. Light S o c k e t and W i r e A s s e m b l y 110454 O v e r r i d e (2) 128647
Plug, 3 130253 45. A r m a t u r e and E y e l e t A s s e m b l y 133411
P i n (3) 132000 46. M a g n e t and B r a c k e t A s s e m b l y 133410
15. L i g h t B r a c k e t , R e c o r d P l a y i n g 134883 47. S p r i n g , L e v e r and L i n k 128649
16. S p a c e r , R e c o r d P l a y i n g (2) 134882 48. Lever Assembly, Override 133469
Lockwasher (2) 73604-7 49. Spring, Lever Return 13343 1
17. Window P l a t e a n d R i v e t A s s e m b l y 134592 50. R a t c h e t W h e e l and Hub A s s e m b l y 128363
18. Magnet and F r a m e A s s e m b l y 117987 51. Guide, R a t c h e t L e v e r , O v e r r i d e 128367
19. Mounting B r a c k e t , Window P l a t e 134546 S p a c e r , O v e r r i d e Guide ( 2 ) 135185
20. Mounting P l a t e and S p a c e r 52. S w i t c h and B r a c k e t A s s e m b l y ,
Assembly 134003 Override 133472
21. M o t o r and G e a r A s s e m b l y 133487 Switch 129370
Plug, 2 129377 Mounting B r a c k e t , S w i t c h 64991
P i n (2) 132000 Retainer Plate 63014
22. Mounting B r a c k e t and R o l l e r 53. Mounting P l a t e and S t u d A s s e m b l y ,
Assembly 133467 Override 133474
23. R e t a i n i n g R i n g 73724-9 54. Lamp 135165
24. P i v o t S h a f t 135154 55. Light S o c k e t 122358
25. B r a c k e t , P l a y m e t e r R e s e t 135150 56. Mounting B r a c k e t and P i n A s s e m b l y 132725
26. P l a y m e t e r R e s e t A r m A s s e m b l y 135160 57. Switch, M a g a z i n e L o c k 128344
27. R e s e t L e v e r 133097 Tapping P l a t e , Pivot Casting 128283
28. Mounting B r a c k e t , R e s e t L e v e r 133377 58. L o c k i n g A r m and L i n k A s s e m b l y 133991
29. R e t a i n i n g R i n g 73724- 12 S t o p Nut, 8 - 3 2 74988-12
30. S h a f t , R e s e t L e v e r 133379 S t o p Nut, 4 - 4 0 74988-7
31. C o n t a c t B o a r d and W i r e A s s e m b l y 133988 Shoulder Screw, Magazine Lock 129819
32. C a n c e l Solenoid A s s e m b l y 133476 S p a c e r , M a g a z i n e L o c k (2) 129818
Internal H a i r P i n (2) 74402- 1 Spring, Magazine Lock 128748
Cup W a s h e r ( 2 ) 64766 59. Solenoid, M a g a z i n e L o c k 128343
Spring (2) 64780
P l u n g e r (2) 133374

-
WURLITZER Page 27C
SECTION C

-
RECORD MAGAZINE ASSEMBLY

1. L a b e l , R e c o r d P l a y i n g 3400
Label, Record Playing
Filler, Record
Magazine 3400 3460 134806
-
2. L a b e l , R e c o r d Magazine, F i l l e r , R e c o r d Magazine 3460 134894
Loading 3400 S u p p o r t B r a c k e t , F i l l e r (2) 3460 134896
Label, Record
M a g a z i n e , Loading
Mounting B r a c k e t and
Label Assembly 135258
-
3. R e c o r d S e p a r a t o r A s s e m b l y F i l l e r , R e c o r d Magazine (2) 3410 134895
4. Casting, R e c o r d Holder S u p p o r t B r a c k e t , F i l l e r (2) 3410 134896
5. P l a t e , R e c o r d Magazine
6 . G e a r , R e c o r d Magazine
Mounting B r a c k e t and L a b e l
A s s e m b l y (A & B ) 135256
-
Mounting B r a c k e t and L a b e l
A s s e m b l y (F & G) 135257
R e c o r d S e p a r a t o r (2) 132972 -
Page 28C WURLITZER
 SECTION C

RECORD TAKEOUT ARM

1. R e t a i n i n g R i n g (4) 73724-12 21. Retaining Ring 73724-31

2. R o l l e r A s s e m b l y , R e c o r d 22. Washer 65778
A r m (2) 133468 23. Spring Washer 73632-109
S h a f t , R e c o r d A r m R o l l e r (2) 133378 24. P i v o t C a s t i n g and S h a f t
3. R e c o r d A r m A s s e m b l y 133547 Assembly 132675
4. B e v e l G e a r , R e c o r d A r m 128092 25. Gear and P l a t e Assembly 128587
5. W a s h e r 128093 26. Retaining Ring 73727-50
6. S p r i n g W a s h e r 73632-36 27. Washer, Pivot Casting 128101
7. R e t a i n i n g R i n g 73727-56 28. B a i l and Bushing A s s e m b l y 128589
8. Sleeve, Pivot Casting 132671 29. Holdout C a m 135179
9. G e a r and P l a t e A s s e m b l y 128585 30. Washer 128164
10. R e t a i n i n g R i n g 73727-50 31. Pivot Casting and Bushing
11. W a s h e r , P i v o t C a s t i n g 128101 Assembly 133556
12. B a i l and B u s h i n g A s s e m b l y 128590 32. S w i t c h and B r a c k e t A s s e m b l y ,
13. S p r i n g , R e c o r d A r m 128533 Side 2 133976
14. W a s h e r 128217 Switch 128344
15. R e t a i n i n g R i n g (4) 73724-12 Mounting B r a c k e t , S i d e 2
16. P i n Coupling (2) 135155 Switch 133332
17. Coupling, C o n n e c t o r 135176 33. Mounting P l a t e and P i n

- 18. Coupling
Roll Pin
128170
73782-35 34.
35.
Assembly
Spring, Record Clamp
R e c o r d C l a m p and P i n
133372
128520
19. P i v o t C a s t i n g and B u s h i n g
Assembly 133565 Assembly 133434
36. Retaining Ring 73724-60
- 20. C o n n e c t i n g R o d , B a i l 128107

WURLITZER . Page 29C

 SECTION C

CAM AND GEAR ASSEMBLY ILLUSTRATED PARTS LIST

- 1. Coupling 128169
132845
31. M o t o r B r a k e A s s e m b l y
Mounting P l a t e and P i n A s s e m b l y 133484
133485
2. C a s t i n g , G e a r Housing
3. Mounting B r a c k e t , T r a n s f e r S w i t c h 128724 S c r e w , 6 - 3 2 x 3 / 1 6 R d . S e m (2) 73533-21
4. Switch T r a n s f e r 128344 L e v e r and P a d A s s e m b l y 133429
- 5.
Tapping P l a t e
Retaining Ring
128283
73727-25
Spring, Motor B r a k e
Locknut #4-40
133428
74988-7
6. Washer 133145 Washer 53519

- 7.
8.
Actuating A r m and Hub A s s e m b l y
Spring - R e c o r d Takeout Segment
Gear
133121

133096
Roll P i n
Solenoid, C a n c e l
73782-2
135196
S c r e w , 6-32 x 3 / 1 6 R d . S e m (2) 73533-21
9. A c t u a t i n g A r m and Hub A s s e m b l y 1331 15 Washer (2) 42120
Segment Gear - Record T r a n s f e r
- 10.
11.
12.
Roller Bracket Assembly
Mounting P l a t e a n d Shaft
133144
132869
32. C a m , R e c o r d C l a m p
( P a r t of C a m A s s e m b l y , 128159)
Roll Pin
128152

73782-36
Assembly, Record Transfer 135156 33. C a m , T u r n t a b l e R e s e t 128153
13. Retaining Ring 73728-37
- 14. Shaft and G e a r A s s e m b l y -
Record Transfer 128118
( P a r t of C a m A s s e m b l y , 128159)
Roll Pin
34. P i v o t P l a t e and L e v e r A s s e m b l y
73782-36
133719
15. Shaft - C a m s 128131 L e v e r and B u s h i n g A s s e m b l y 132903
16. Retaining Ring (2) 73728-37 Retaining Ring 73724-25
- 17. Cam - Record Release 128154 P i v o t P l a t e and S t u d A s s e m b l y 133794
( P a r t of C a m A s s e m b l y , 128159) S c r e w , 8-32 x 3 / 8 R d . S e m (2) 73533-36
Roll P i n 73782-36 35. C a b l e A s s e m b l y , T u r n t a b l e
18. T r a c k C a m and P i n A s s e m b l y 129332 Drive Pulley 128500
- ( P a r t of C a m A s s e m b l y , 128159)
Roll P i n 73782-49
36. R e t a i n i n g R i n g ( 2 ) 73724- 1 8
37. P i v o t P l a t e and L e v e r A s s e m b l y 133720
19. C a m - T o n e A r m Swing 128157 Lever and Bushing A s s e m b l y 132905
( P a r t of C a m A s s e m b l y , 128159) Retaining Ring 73724-25
- Roll P i n 73782-33 P i v o t P l a t e and S t u d A s s e m b l y 128240
20. Retaining Ring (2) 73724-18 S c r e w , 8 - 3 2 x 318 ~ d S.e m ( 2 ) 73533-36
21. Link, R e c o r d C l a m p 128275 38. C a m , T o n e A r m L i f t 128155
L e v e r and B u s h i n g A s s e m b l y -
- 22.

23.
Record Clamp
Spring
132901
59606
( P a r t of C a m A s s e m b l y , 128159)
Roll Pin
39. C a m , T u r n t a b l e D r i v e
73782-36
128156
24. Retaining Ring 73724-25 ( P a r t of C a m A s s e m b l y , 128159)
25. Stud Pivot 128129 Roll Pin 73782-36
- Lockwasher #8 73604-6 4 0 . P i v o t P l a t e and L e v e r A s s e m b l y 133721
26. A d j u s t m e n t L e v e r and L e v e r , L e v e r and B u s h i n g A s s e m b l y 132907
Pin Assembly 128160 Retaining Ring 73724-25

- 27.
Roll P i n
C a s t i n g - G e a r Housing
Shoulder Screw (2)
73782-32
132646
128182
P i v o t P l a t e and S t u d A s s e m b l y
S c r e w , 8-32 x 318 R d . S e m ( 2 ) 73533-36
41. M i c r o S w i t c h , C a n c e l
12824 1

128418
S t o p Nut, 8-32 (2) 74988-12 42. Mounting B r a c k e t a n d P l a t e
Shaft - Housing
- 28.

29.
S c r e w , 8-32 x 1 / 2 R d . S e m (2) 73533-38
Mounting B r a c k e t and S p a c e r
128151 Assembly
43. R e t a i n i n g R i n g
44. Stud, P i v o t - R e c o r d R e l e a s e
12866 1
73728-25
128180
Assembly - Drive Motor 128251 45. L e v e r and B u s h i n g A s s e m b l y 132911
30. M o t o r and G e a r A s s e m b l y 133526 46. Link, R e c o r d R e l e a s e 128141
- Gear, Motor 135259 Retaining Ring 73724- 1 8
Roll P i n 73782-32

-
WURLITZER Page 31 C
SECTION C

TURNTABLE ASSEMBLY ILLUSTRATED PARTS LIST

Ring, T u r n t a b l e 128022 Washer

S c r e w , 6-32 x 318 T r u s s (3) 76719-68 R e t a i n i n g R i n g (2)
L o c k w a s h e r (3) 73604-5 W a s h e r (2)
Turntable 128038 S p r i n g , P i l o t L e v e r (2)
Pad 128042 Washer, Felt
P i l o t Guide and Shaft Retaining R i n g (2)
Assembly, Turntable 128041 Mounting P l a t e A s s e m b l y ,
Bushing 128179 Clamp L e v e r s
S u p p o r t C a s t i n g and Bushing Tube, Pilot
Assembly, Turntable 128023 Spring, C a m
S c r e w , 8-32 x 114 P a n . Cup Was h e r
S e m . (3) 74416-34 Retaining R i n g
Retaining Ring 73727-43 Shaft, C a m
Cup W a s h e r (2) 124530 Cam, Clamp Lever
Spring, Pilot 128007 Pilot, Turntable
R e t a i n i n g R i n g (2) 73724-25

-
Page 32C WURLITZER
 SECTION C

TONE ARM ASSEMBLY ILLUSTRATED PARTS LIST

1. T o n e A r m and P i v o t R o d A s s e m b l y 11. S p r i n g (4 112 o z . a t 1 1 5 / 3 2 " )

Tone A r m 12. A d j u s t m e n t L e v e r a n d B u s h i n g
B a l a n c e B r a c k e t and Weld S c r e w Assembly
Assembly 13. W a s h e r
Pivot Rod, Tone A r m 14. S p r i n g ( 1 ~ b .12 oz. a t 1 5 / 1 6 " )
2. Weight and S t o p Nut A s s e m b l y 15. L e v e r and B u s h i n g A s s e m b l y
3. W i r e a n d P l u g A s s e m b l y 16. R e t a i n i n g R i n g
Plug, 4 Prong 17. R e t a i n i n g R i n g ( 3 )
C l i p (5) 18. P i v o t A r m and P i n A s s e m b l y
4. Mounting B r a c k e t and S t o p Nut 19. C u p W a s h e r
Assembly 20. S p r i n g
Pivot Screw, Tone A r m 21. C u p W a s h e r
5. S p r i n g (1 Ib. 12 o z . a t 1 5 / 1 6 " ) 22. R e t a i n i n g R i n g
6. A d j u s t i n g B r a c k e t and S t o p Nut 23. L i n k , T o n e A r m F e e d I n
Assembly 24. R e t a i n i n g R i n g ( 2 )
7. W a s h e r (2) 25. T u b e , T o n e A r m
8. B a l l R a c e , T o n e A r m S h a f t 26. S h a f t
9. S u p p o r t C a s t i n g and B u s h i n g 27. C a r t r i d g e
Assembly N e e d l e , Double T i p D i a m o n d
10. Mounting B r a c k e t , T o n e A r m

-
WURLITZER Page 33C
 SECTION C

TURNTABLE AND MOUNTING PLATE ASSEMBLY ILLUSTRATED PARTS LIST

1. "0" R i n g 128579 23. Mounting P l a t e , S p e e d C h a n g e 128026

2. Retaining Ring 73724-25 S c r e w , 8-32 x 114 R d . S e m . (2) 73533-24
3. Drive Wheel A s s e m b l y 128032 24. M o t o r and S l e e v e A s s e m b l y 129391
S c r e w , 6-32 x 5 / 1 6 R d . S e m . (3) 73533-23
....
......
.........
..........
........
..........
4. Retaining Ring 73724-25 ...........
5. Cup W a s h e r 124530 Plug - 2 129377 ..........
...........
...........
.......
...........
...........
..........
_.I

6. Spring, Shift, Turntable Drive 128534 P i n (2) 132000 ..........

.........
........
.........
....
......
7. Spring, Drive Wheel A r m 25. O i l T u b e 128727
(6 112 o z . a t 1 1 / 8 " ) 133543 S c r e w , 6-32 x 5 / 1 6 R d . S e m . 73533-23
8. A r m , Hub and L i n k A s s e m b l y 128537 Washer 42120
9. Shaft, Pivot, Bell C r a n k 124519 Cable Clamp 73804-2
10. Spring, Turntable Return 26. Mounting B r a c k e t , T u r n t a b l e P l a t e 133460
(6 112 oz. a t 1 1 / 8 " ) 133543 S c r e w , 8-32 x 5/16 Rd. S e m . 73533-35
11. R e t a i n i n g R i n g (2) 73724-18 Spacer 134864
12. B e l l C r a n k a n d Hub A s s e m b l y , Lockwasher 73604-6
L. H. 128046 W a s h e r (2) 54024
13. S p r i n g , Solenoid A s s i s t (8-10 oz. 27. R u b b e r Mount (4) 60882
a t 2 5/16") 124487 N u t (8) 73601-7
14. R e t a i n i n g R i n g (2) 73724- 15 L o c k w a s h e r (8) 73604-6
15. S h a f t , Solenoid, B e l l C r a n k 124518 28. M o t o r Mounting and P i v o t
16. P l u n g e r , Solenoid 121095A Bracket Assembly 128054
17. S o l e n o i d and Plug A s s e m b l y 129423 29. Mounting B r a c k e t , T u r n t a b l e P l a t e 133642
S c r e w , 6 / 3 2 x 5 / 1 6 R d . S e m . (2) 73533-25 S c r e w , 8-32 x 5 / 1 6 R d . S e m . 73533-25
Washer (2) 42120 Spacer 134864
Solenoid 121095 Lockwasher 73604-6
Plug - 3 130253 W a s h e r (2) 54024
P i n (2) 132000 30. B e l l C r a n k a n d Hub A s s e m b l y , R . H. 128045
18. Retaining Ring 73727-50
3 1. Mounting P l a t e and R o l l e r
19. Washer 124521
Assembly 128173
20. Washer, Felt 124520
21. Receptacle - 3 130524
22. M i c r o Switch 60655
S c r e w , 6-32 x 1 R d . S e m . (2) 73533-30
Tapping P l a t e 128025
Plug - 3 130253
P i n (2) 132000

-
WURLITZER Page 35C
 SECTION C

RECORD CHANGER ILLUSTRATED PARTS LIST, R , H .

1. Mounting B r a c k e t and S i l k S c r e e n 37. S p r i n g 115821
Assembly 134872 38. R e c o r d A r m R e s t and Nut A s s e m b l y 132862
2. S c a n Switch 129432 39. B r u s h H o l d e r and B r u s h A s s e m b l y 133982
3. P i v o t B r a c k e t and S t o p Nut B r u s h Holder 135280
Assembly 128611 Brush 135180
4 . S t o p and B e a r i n g A s s e m b l y , L . H . 128609 40. P l u g , 15 M o l e x 131887
Spring Washer 73632-4 P i n (11) 132000
Washer 54024 4 1 . S p r i n g ( 3 l b s . a t 2 1/411) 119426
Retaining Ring 73724- 1 8 4 2 . Mounting B r a c k e t and P i v o t L e v e r
Retaining Ring 73724-15 Assembly 113944
5 . Mounting B r a c k e t , S a f e t y Switch 133494 4 3 . Link and S p r i n g P i n A s s e m b l y ,
6. Mounting P l a t e , S a f e t y S w i t c h 133902 Front 135190
7. S w i t c h , S a f e t y 133928 44. S p r i n g (4 112 o z . ar. 1 1 5 / 3 2 " ) 5 98 94
8. S t o p B r a c k e t a n d Nut A s s e m b l y , 45. L i n k and S p r i n g A s s e m b l y , R e a r 135193
Record A r m 133078 46. K e s i s t o r , 27 o h m , l o % , 1 / 2 W. 72154-32
9. B r a c k e t , S i d e 1 S w i t c h 133437 47. C a p a c i t o r , 4 7 Mfd. , 4 0 0 V 71549-14
10. S w i t c h and B r a c k e t A s s e m b l y , 48. R e c e p t a c l e , 2 129382
Side 1 133975 49. R e c e p t a c l e , 6 131171
Switch, Side 1 128344 50. S t r a i n R e l i e f 71878-14
Adjusting B r a c k e t 133881 51. R e c e p t a c l e , 15 131888
11. S t o p and B e a r i n g A s s e m b l y , R . H. 128610 52. R e l a y , R e d 122366
Spring Washer 73632-4 Socket 122131
Washer 54024 Retainer, Socket 122132
Retaining Ring 73724- 1 8 53. R e c e p t a c l e , 12 131175
Retaining Ring 73724-15 54. R e c e p t a c l e , 9 131173
12. P i v o t B r a c k e t and S t o p Nut 55. R e c e p t a c l e , 3 1 30254
Assembly 128611 56. R e c e p t a c l e , 2 129382
13. L e v e r and S h a f t A s s e m b l y , 57. C h a s s i s P a n and S i l k S c r e e n
Record Clamp 133493 Assembly 134008
14. P u l l L e v e r and B u s h i n g A s s e m b l y 132668 58. S i d e , C o n t r o l Unit 133508
15. S p r i n g 133869 59. C o v e r , C o n t r o l Unit 133480
16. B e a r i n g B r a c k e t and B u s h i n g 60. R e l a y , White ( 2 ) 122133
Assembly 128194 Socket 122131
17. R e t a i n i n g R i n g 73724- 1 8 Retainer, Socket 122132
18. Shaft a n d L e v e r A s s e m b l y 128204 61. L a m p S o c k e t 122358
19. S p r i n g , T o n e A r m R e l e a s e 62. L a m p #305 135165
L e v e r ( 4 5 / 1 6 oz. a t 2 5 / 1 6 " ) 65096 63. R e l a y 135 242
20. Link, T u r n t a b l e Shift 128273 64. S p r i n g (4) 61059
21. S p r i n g 65958 65. R e t a i n e r , C h a s s i s S p r i n g (4) 134735
22. Link, T u r n t a b l e Shift 128274 66. L e v e r and Hub A s s e m b l y ,
Retaining Ring 73724- 1 8 Turntable Reset 128229
23. Mounting B r a c k e t A s s e m b l y , 67. S h a f t and L e v e r A s s e m b l y ,
T r i p Switch 133492 Turntable Reset 133941
24. T r i p S w i t c h a n d P l u g A s s e m b l y 133974 68. Mounting B r a c k e t a n d B u s h i n g
Switch, T r i p 121929 A s s e m b l y (2) 128226
Plug, 3 130253 69. A d j u s t m e n t P l a t e a n d P i v o t
25. S p r i n g 134759 Assembly, Turntable 133971
26. Mounting B r a c k e t , M u t e / P l a y 70. B a l l R a c e 59679
Switch 134142 71- Solenoid and Plug A s s e m b l y 128627
27. M u t e / P l a y S w i t c h 131331 Plug, 2 129377
28. R o l l e r B r a c k e t and S t u d A s s e m b l y 128245 Contact, 2 132001
29. R o l l e r , T u r n t a b l e D r i v e 128248 Mounting B r a c k e t and S o l e n o i d 132885
Retaining Ring 73724- 18 72. S o l e n o i d P l u n g e r L i n k A s s e m b l y 128626
30. B r a c k e t and S t o p Nut A s s e m b l y , Pin 121240
Tone A r m 132991 Washer 4 87
31. S u p p o r t , R e c o r d C h a n g e r ( F o r Cotter P i n 23355
S e r v i c e Only) 134906 Link 56608
32. Mounting P l a t e and S o c k e t Link and P i n Assembly 128615
Assembly 133978 Retaining Ring 73724-15
S o c k e t , 4 Min. 69090 L i n k and P i n A s s e m b l y 128614
33. B r a c k e t and S t o p Nut A s s e m b l y , W a s h e r (2) 4 87
Turntable Stop 133973 73. P i v o t B r a c k e t and B u s h i n g
34. L i n k , T o n e A r m L i f t 133395 Assembly 128208
Retaining Ring (2) 73724- 18 74. S e r v i c e S w i t c h 121301
35. Lift L e v e r A s s e m b l y , T o n e Lockwasher 73607- 13
A r m Lift 133137 Insulator 135273
36. S p r i n g 59612 75. Mounting P l a t e , R e c o r d C h a n g e r 133373

WURLITZER Page 37C

3400 PHONOGRAPH

Page ID
SECTION D

-
Page 2D WURLITZER
 SECTION D

- CABINET - FRONT VIEW - 3400 SERIES

Extrusion, Upper Door, Front Extrusion, Intermediate, Wrap Around

Inlay, Top Extrusion, F r a m e
Top Plate, Steel Glass Clamp, Top and Bottom
Extrusion, Top Rear Glass Clamp, Ends
Glass, Display, 34-7/16" x 7-1/8" Glass, Statesman by Wurlitzer
Tape, 9/16" Coin Return Cup
.
Glass Clamp, L .H Side Frame, Cash BOXDoor
Glass Clamp, R.H. Side Lock and Key Assembly
Glass Clamp, Lower Cash Box Door
Display Sign, Mountain Scene Guard
Mounting Panel, Front, Display Sign Coin Bag
Mounting Panel, Rear, Display Sign Retainer, Vinyl Overlay, R .H .
Extrusion, Selector Panel 3400 Retainer, Vinyl Overlay, L .H .
Extrusion, Selector Panel 3460 Extrusion, Bottom
Extrusion, Selector Panel 3410 Vinyl Overlay
Inlay, Service Card Holder Moulding, Base
Window, Service Card Extrusion, Lower Grille
Grille Screen Special Stud
Instruction Casting Grille Screen (3)
Instruction and Select Label, L .P. Polyurethane Backing, Upper
Coin Denomination and Select Label Polyurethane Backing, Center
Instruction Label, Top Tunes Polyurethane Backing, Lower
Instruction Label, Top Tunes and L .P. Extrusion, Grille F r a m e (3)
Window Blank (2) Special Stud
Window Clamp F r a m e Palnut
Light Box and Partition Extrusion, Inner Grille, L .H .
Light Socket (3) Extrusion, Inner Grille, R.H .
..
Lamp, G E 12 (3) Inlay, Door, Front
Coin Denomination and Dancers Label Inlay, L.H.
Coin Denomination Label, L .P. Casting, Upper Door L .H .
Escutcheon Label, Dancers .,
Separator, L .H A1 -CO 3400
Window Blank (2) Separator, L .H ., A1 -B8 3460
Window Clamp F r a m e Separator, L .H ., Al-A0 3410
Window Clamp (2) Separator, R.H ., TI-VO 3400
Coin Entry Instruction Label Separator, R.H ., U1-V8 3460
Window Blank (2) Separator, R .H ., K1 -KO 3410
Window Clamp F r a m e Separator, B1-GO 3400
Casting, Upper Door, R.H . Separator, C1-F8 3460
Inlay, R.H. Separator, B1 -CO 3410
Reject Button Separator, F 1 -LO 3400
Retaining Ring i Separator, G1-K8 3460
Rubber Washer Separator, Dl-EO 3410
Washer Separator, K1 -QO 3 400
Medallion Separator, L1-P8 3460
Speed Nut Separator, F 1 -GO 3410
Tape, Inlay, Adhesive (2) Separator, PI -UO 3400
Glass, Door, 38" x 12" Separator, Q1-T8 3460
Tape, 9/16" Separator, H1 -JO 3410
Extrusion, Door Extrusion, Center, Door
Extrusion and Guard, R.H. Retainer, Program Separator
Extrusion and Guard, L .H . Extrusion, Personalization F r a m e
Collar, Vinyl Clad Window, Personalization
Extrusion, Top, Wrap Around Display Sign, "Music for Millions"
Extrusion, Top, Front Color Shield
Lock, RW-105 Light Diffuser
Key, RW-105 Retainer (2)
Washer Casting, Speaker F r a m e
Pin and Lock Lever

-
WURLITZER Page 3D
SECTION D

Page 4D WURLITZER
 SECTION D

CABINET - REAR VIEW

Upper C r o s s Rail Assembly

Hinge
Fluorescent Lamp, 30 W., 36", Daylight
Playmeter Reset Assembly
Socket, Lamp
Lock Lever and Shaft Assembly
Spring
Bracket and Plate Assembly, L .H .
Bracket and Plate Assembly, R .H .
Starter, FS -4
Socket
.
Ballast, 30 W
Extrusion, Rub Rail, L .H .
Extrusion, Rub Rail, R.H.
Stop Lever & Pin Assembly
Spring
Mounting Plate and Guide Bracket
Support Bracket and Roller
.
Cable Retainer, L .H
Cable Retainer, R .H .
Speaker, 12" (2)
C a s t e r (4)
Door, Lower Back
Coin Bag Housing
Coin Bag Housing, Short, Export
Back Rail Assembly
Strike and Lever
Lock, Back Door, RW-105
Key, RW-105
Latch & Pin (2)
Chassis Mounting Rail, R .H .
Chassis Mounting Rail, L .H .
Coin Return Chute
Light Diffuser, Lower Grille
Mounting Plate and Clip Assembly
Wing Nut, 6-32 (6)
Special Stud (6)
Catch, Grille Screen (4)
Clip, Grille Screen (4)
Rivet

Page 5D
SECTION D

-
Page 6 0 WURLITZER
 SECTION D

CABINET - FRONT INTERIOR VIEW - 3400 SERIES

Speaker, 6", L.H.

Capacitor, 4 MFD ., 25 V ., Non-Polarized
Speaker, 3" x 5", L.H .
Capacitor, 1 MFD., 100 V."
.
Bracket, Selector Switch, L .H
Speaker, 3" x 5", R.H.
Capacitor, 1 MFD ., 100 V .
Speaker, 6", R.H.
.
Capacitor, 4 MFD , 25 V ., Non-Polarized
.
Bracket, Selector Switch, R .H
Light Diffuser Assembly
Spring (2)
Shaft
Mounting Bracket
Cable Retainer
Fall Support and Pin (2)
Guide and Latch Assembly, R.H.
Guide and Latch Assembly, L .H .
Cam, Light Diffuser
Roll Pin
Socket, Lamp (2)
Box, Coin Register ~ e c h a n i s m
Grommet (3)
Spring, Fall Support Stop (2)
Spring, Fall Support Return (2)
Ballast, 25 W .
Starter, 25 W ., FS-25
Socket
Fluorescent Lamp, 25 W ., 33", Daylight
Cam, Light Disfuser
Roll Pin
"0" Ring
Motor, Light Diffuser
Mounting Plate
Rubber Mount (3)
Pulley
Set Screw
Mounting Bracket

WURLITZER Page 7D
SECTION D

PROGRAM HOLDER

Insert, Upper 3410 134771 8. Insert, Upper 3410

L .P. Program Label 3400-3410 134665 9 . Program Holder, Center
Extrusion, A1-CO 3400 125451 Red Program Label 3400
Extrusion, Bl-GO 3400 125452 L .P. Program Label 3460
Extrusion, El-LO 3400 125453 10. Insert, Upper 3410
Extrusion, K1-QO 3400 125454 11. Insert, Upper 3410
Extrusion, PI-UO 3400 125455 12. Classification Slip
Extrusion, TI-VO 3400 125456 13. Program Holder F r a m e Assembly
Extrusion, A1-B8 3460 134596 14. Program Slip Cover, Gold
Extrusion, C1-F8 3460 134597 Program Slip Cover, Red
Extrusion, G1-K8 3460 134598 15. Slide and Catch Assembly
Extrusion, L1-P8 3460 134599 Slide Catch
Extrusion, Q1-T8 3 460 134600 Spring
Extrusion, U1-V8 3460 134601 Retaining Ring
Extrusion, A1-A0 3410 125457 15A. Lock Catch, Door, R.H .
Extrusion, B1-CO 3410 125458 Lock Catch, Door, L .H .
Extrusion, Dl- EO 3410 125459 16. Insert, Lower 3460-3410
Extrusion, Fl-GO 3410 125460 17. Insert, Lower 3460-3410
Extrusion, H1-JO 3410 125461 18. Insert, Lower 3460-3410
Extrusion, K1-KO 3410 12,5462 19. Insert, Lower 3460-3410
Insert, Upper 3410 134772 20. Light Shield, Lower 3400
Gold Program Label 3400 134921 Light Shield, Lower 3460-3410
Program Holder (4) 128804 21. Red and Gold Program Label 3460
Light Shield, Upper 3400 -3460 134865 22. Insert, Lower 3460-3410
Light Shield, Upper 3410 129119
15A is Mounted on Door Casting

Page 8D WURLITZER
 SECTION E

SEQUENCE OF OPERATIONS

-
WURLITZER Page 1 E
SECTION E

ELECTRICAL SEQUENCE
STATESMAN

The electrical sequence of operation has been especially prepared to assist in trouble shooting the
electrical circuitry of the Statesman Phonograph.
Individual circuits have been lifted from the master wiring diagrams anu presented sequentially in
functional form. This enables one to trace and trouble shoot the electrical circuitry step by step
from the closing of a coin switch - the establishment of a credit - the making of a selection - the
playing of a record. Each of the essential circuits may thus be traced with a minimum of "wading
through schematics " .
Each circuit of the wiring diagrams ( s e e Section G ) is numbered, the circuit number designates the
wire color, see wiring diagram color code, Section G .

In the following schematics the encircled numbers designate the circuit numbers: for example ...
KEY SERIES SWITCHES RELAY 1
SWITCH NUMBER LETTER COIL

The 42 circuit connects the key switch to the normally closed number series switch. A jumper con-
nects the number series switch to the normally closed letter series switch. The 47 circuit connects
the letter series switch to the coil of relay 1.
Relays a r e designated RY -1, RY -2, etc . ; RY -1 (13) indicated relay 1, terminal 13; RY -2 (10-6)
indicates relay 2, terminals 10 and 6 . Blade switches a r e numbered in accordance with illustration
shown below .
0
The 32 circuit is common ground at junction box and amplifier.
. .
The
0
35
circuit is -28 volts D C
.
The
0
40
circuit is 24 volts A. C

SELECTOR
? ? ?
3- +
SWITCHES RESISTOR
,-
I
TT
.J
.J
.
I '
L -S-. JA. I
NORMALLY
CLOSED -1 CAPACITOR TOP TUNES STEPPER
JUMPER JUMPER
NORMALLY COIL OR
I-
OPEN CATHODE ANODE
' + , DIODE
- - -
MOTOR
ZENER DIODE

-
ALL SWITCHES SHOWN
IN REST POSITION
-7
SLIP
RING

FUSE

METHOD O F NUMBERING SWITCH AND RELAY CONTACTS

Page 2E
 SECTION E

3400 SELECTION SEQUENCE

1. 254 COIN SWITCH

a. Closing the 25$ COIN SWITCH energizes the 254 COIN MAGNET, releasing the 25$ a c -
cumulator and cancel wheels thereby allowing the cancel wheel to advance to the two credit
position closing the key switch and the 254 credit switch.

25C 25C
COIN RY-8 COIN CIRCUIT 24 Vn
SWITCH 12-4 MAGNET BREAKER A, C.

b. 25$ CREDIT SWITCH

Closing the 25$ CREDIT SWITCH energizes RY -8.

2 5C 25C
CREDIT RY-8 COIN CIRCUIT
SWITCH COIL MAGNET BREAKER

c. 504COINMAGNET
2nd quarter deposited now energizes the 50$ COIN MAGNET.

2 5C 50C
COIN RY-8 COIN CIRCUIT 24 V,
SWITCH MAGNET BREAKER AmCm

2. KEY SWITCH
a. Closing the KEY SWITCH energized RY-1, which is then interlocked thru contacts 12-8 of
RY -1.
STEPPER

KEY SERIES SWITCHES

-
C

WURLITZER Page 3E
SECTION E
-
b. Closing the L .P. SWITCH energizes RY -4, see paragraph 3 .

L, Pa RY-22 RY-21 RY-1 STEPPER

SWITCH RY-4 3-11 1-9 5-9 LATCH RY -28 V.

3. SELECTOR SWITCH LATCH SOLENOID

Relay 1 energizes the LATCH SOLENOID. The LATCH SOLENOID CONTROL SWITCH removes
a shunt from across the current limiting resistor and turns on the SELECT LAMP. Standard
selection buttons will remain latched when pressed. L .P. selection buttons will remain latched
when pressed provided the L .P. SWITCH is closed.

_------L,POSITION
I

P, CONVERSION SWITCH A IN L. Pa I
L. P. SELECTOR SWITCH A
I
L. P, CONVERSION SWITCH B IN STANDARD 1
POSITION I
L, P, SELECTIONS ONLY I
I
A-1 SELECTED
,,,,, - - - - I
L, P, CONVERSION
SWITCHES IN

STEPPER
R Y-1 LATCH
RY-22 RY-21
SWITCH SOLENOID OHM

LATCH SOLENOID CONTROL

SWITCH

NOTE

The L.P. selection sequence is identical to the standard selection sequence with the exception of the
coin mechanism cancel and selector switch counter circuits, see paragraph 8 .
-
Page 4E WURLITZER
 SECTION E

4. B-1 Selected
a. Selector LETTER and NUMBER SWITCHES a r e now closed completing the circuit to LET-
T E R and NUMBER patches on SELECTION ACCUMULATOR CONTACT BOARD.

SELECTION SELECTION
LATCH ACCUMULATOR ACCUMULATOR
SOLENOID CONTACT CONTACT
CONTROL NUMBERSELECTOR PUITE SELECTOR
SWITCHES MAGNET

LETTER
PATCHES PATCHES

LATCH
SOLENOID SELECTOR LETTER
STEPPER CONTROL SWITCHES
500 MFD LATCH
SWITCH
RELAY
4-5

-28 V,

b. NUMBER AND LETTER LATCH SWITCHES

Closing of the LATCH SWITCHES energizes RY - 2 .

STEPPER
LETTER NUMBER LATCH -28 V.
RY-1 RY-2 LATCH LATCH RELAY
Dm C.
SWITCH SWITCH 9-10
0 22
[
I
_ O- II s8Jm I

L,---1

6. SELECTION ACCUMULATOR MOTOR

RY-2 completes the circuit to the SELECTION ACCUMULATOR MOTOR. The SHAFT. and
MAGNET ASSEMBLY will now rotate over selector contact board assembly approximately 180°,
completing circuits to RY-3, CANCEL SOLENOID and KEYBOARD COUNTER, SfLECTOR
MAGNET and OVERRIDE MAGNET. RY -3 will be released at the end of the 180 rotation,
breaking the circuit to the SELECTION ACCUMULATOR MOTOR.
24 V.
RY-2 A. C8
0 - - 159

RY-3
0
SELECTION
ACCUMULATOR
MOTOR

WURLITZER Page 5E
SECTION E

When Energized
a. Setso up a full cycle circuit f o r the SELECTION ACCUMULATOR MOTOR to provide
180 rotation of the SHAFT and MAGNET ARM ASSEMBLY.

b. Breaks the circuit t o RY -1 . RY -1 releases after its capacitor discharges .

1. KEYBOARD LATCH SOLENOID now released.
2. RY -2 now released.

c. Preparatory circuit s e t up t o the COIN MECHANISM CANCEL SOLENOID.

1. Credit cancelled off during rotation of the SHAFT and MAGNET ARM ASSEMBLY
and circuit completed t o KEYBOARD COUNTER.

SELECTION
ACCUMULATOR RY-3
CONTACT COIL
annan

8. COIN REGISTER MECHANISM CANCEL SOLENOID AND SELECTOR SWITCH COUNTER

The COIN REGISTER MECHANISM and SELECTOR SWITCH COUNTER a r e energized a s the
SHAFT and MAGNET ARM ASSEMBLY r o t a t e s . One credit will be cancelled for a standard
selection. The number of credits cancelled for an L . P. selection is determined by the place-
ment of bridging screws on the CANCEL OPTTON BOARD.

- - - L. P. SELECTIONS ONLY
CANCEL OPTION
- 1

STEPPER

SELECTOR ACCUMULATOR
CONTACT BOARD
I , 1
Page 6E WURLITZER
 SECTION E

9. OVERRIDE MAGNET
T h e OVERRIDE MAGNET is energized during the rotation of the SHAFT and MAGNET ARM
ASSEMBLY. When energized, a two tooth escapement is released closing the OVERRIDE
SWITCH.
SELECTION
ACCUMULATOR 305
CONTACT LAMP OVERIDE 24 V,
BOARD MAGNET A, C,

10. T h e OVERRIDE SWITCH energizes the OVERRIDE RELAY.

11. OVERRIDE RELAY

When Energized
a. Completes the circuit t o the TURNTABLE MOTOR
TURN
TABLE OVERIDE
DRIVE RELAY 15 :....:....:.:.
:::::::.:.:.:.
MOTOR fl.#A
.m#$ .......
117 VOLTS A. C. ,

........
:.:.:.:.:.:.7
4..
23::::".

b. Energizes the MAGAZINE LOCK SOLENOID, unlocking the RECORD MAGAZINE.

MAIN RUN

12. MAGAZINE DRIVER MOTOR

T h e MAGAZINE LOCK SOLENOID, i n unlocking the RECORD MAGAZINE, closes the MAGA-
ZINE LOCK SWITCH energizing the MAGAZINE DRIVE MOTOR. T h e RECORD MAGAZINE and
READOUT ARM ASSEMBLY scans in a clockwise direction in s e a r c h of the B-1 SELECTOR
LATCH PIN.

MAGAZINE MAGAZINE
SERVICE DRIVE LOCK SAFETY TRANSFER 24 V.
SWITCH MOTOR SWITCH SWITCH SWITCH A. C.

WURLITZER Page 7E
 SECTION E

13. # 1 SIDE SWITCH

The #1 SIDE SWITCH, mounted on the READOUT ARM, closes a s it engages the B-1 LATCH
PIN, energizing the #1 SIDE RELAY. #1 SIDE RELAY interlocked.
CHASSIS CHASSIS
RUN-LOAD CONTACT CONTACT
SCAN #1 SIDE BOARD #1 SIDE BOARD -28 V,
SLIP RING SWITCH SLIP RING 0. C,

14. #1 SIDE RELAY

When Energized
a. Energizes the # 1 SIDE SOLENOID which directs the RECORD ARM to the #1 SIDE
position.

#1 SlDE
RELAY #1SIDE -28 V.
SOLENOID D. C,

....
,...3.; b. Energizes the MAIN CAM RE LAY.
.A::.:.:
, . :...a.
@$$$ MAIN #1 SIDE
.:>> ,.... :.

-
..A
..:.>:.:
-,. PLAY CAM RELAY 24 Vs
8-12 A, C,
T 7

TRANSFER SWITCH

15 . MAIN CAM RELAY

When Energized
a. Releases the MAGAZINE LOCK SOLENOID, locking the RECORD MAGAZINE in B-1
position; the MAGAZINE LOCK SWITCH opens, stopping the MAGAZINE DRIVE
MOTOR.

b. MAIN CAM MOTOR and BRAKE energized driving the MAIN GEAR and CAM t o trans -
f e r the record f r o m the RECORD MAGAZINE t o the TURNTABLE .
OVERRIDE CAM MAIN CAM
117 V, RELAY SERVICE RELAY 117 V,
A. C,

BRAKE

Page 8E WURLITZER
 SECTION E

16. TRANSFER SWITCH

When actuated by the MAIN CAM and GEAR
a. Interlocks the MAIN CAM RELAY, s e e paragraph 1 4 b .
b. Lights t h e RECORD NOW PLAYING LAMP.

RECORD NOW 24 V,
PLAYING LAMP
Am C,
TRANSFER SWITCH

17. #1 SIDE LATCH PIN CANCEL SOLENOID

T h e MAIN GEAR and CAM actuates the PIN CANCEL SWITCH which cancels the B-1 LATCH
PIN.

CHASSIS CHASSIS
PIN 305 #1SIDE CONTACT #1SIDE CONTACT
CANCEL LAMP RELAY BOARD CANCEL BOARD -28Vm
SLlP RING SOLENOID SLlP RING D m C*

:......
. .,::.. :s:..::
18. #1 SIDE RELEASE SWITCH =,;
............
a
:.:.:.:.:.;.
a$:
.
,....
,...
When actuated by t h e RECORD ARM
a. Removes interlock f r o m the # 1 SIDE RELAY, s e e paragraph 1 3 .
b . Energizes t h e RECORD NOW PLAYING INDICATOR.

RECORD NOW #1SIDE

PLAYING RELEASE -28 V,
INDICATOR SWITCH D, C.

- 19. SPEED SHIFT SOLENOID

T h e SPEED CHANGE SWITCH energized t h e SPEED SHIFT SOLENOID when a 33 -1/3 r p m r e -
c o r d is positioned on t h e TURNTABLE.
-
SPEED SPEED
- CHANGE SHIFT
SOLENOID
-28 V.
D, C,

-
WURLITZER Page 9E
SECTION E

20. PLAY SWITCH

T h e MAIN GEAR and CAM actuates the PLAY SWITCH when the RECORD CHANGER i s i n the
play position. The PLAY SWITCH r e l e a s e s the MAIN CAM RELAY which stops the MAIN CAM
MOTOR, s e e paragraph 15b.

PLAY MAIN
SWITCH CAM TRANSFER 24 Vn
SWITCH A, C.

21. TRIP SWITCH

The TRIP SWITCH actuates a s the TONE ARM reaches a predetermined position on the r e c o r d .
When actuated, the TRIP SWITCH energizes the MAIN CAM RELAY starting the MAIN CAM
MOTOR t o r e t u r n the r e c o r d t o the RECORD MAGAZINE, s e e paragraph 15b.

MAlN
TRl P PLAY CAM TRANSFER 24 V.
SWITCH SWITCH RELAY A, C.

0 . 0

NOTES

Page 1 OE WURLITZER
 SECTION E

TOP TUNES

Establishing a half dollar credit in the COIN REGISTER MECHANISM closes the KEY SWITCH and the
TOP TUNES SWITCH. Pressing either the GOLD o r the' RED BUTTON will electrically s e l e c t a p r e -
determined group of selections. A half dollar credit will b e cancelled in the COIN REGISTER
MECHANISM.

1. Closing TOP TUNES SWITCH energizes RY -23 which i s then interlocked

T. T, RED GOLD STEPPER

BUTTON BUTTON

2. Pressing the RED BUTTON energizes RY-22 which energizes RY-20, both relays a r e inter-
locked when RY -2 is energized, see Paragraph 3 .

STEPPER
GOLD RED

3. SELECTION ACCUMULATOR MOTOR

a. RY -2 energized
STEPPER
LATCH -28 V.
RY-1 RY-22 RY-23 RY-1 RELAY D. C.

WURLITZER Page 1 1E
SECTION E
-
b. SELECTION ACCUMULATOR MOTOR energized

RY-2 SELECTION ACCUMULATOR 24 Vm

5-9 MOTOR A, C,

c. RY -3 energized interlocking the SELECTION ACCUMULATOR MOTOR to provide 180'

rotation of the SHAFT and MAGNET ARM ASSEMBLY.

SELECTION
ACCUMULATOR
CONTACT -28 V.
RY-3 Dm C.
BOARD COIL

-
Page 12E WURLITZER
 SECTION E

4. TOP TUNES latch pins released. The number of latch pins released is determined by the
placement of bridging screws on the TOP TUNES OPTION BOARD.

-28 V.
DIODE D, C.
rl

I 1

SELECTION ACCUMULATOR
5W CONTACT PLATE
MFD

RY-22
5-9

TUNES
OPTION
GOLD RED BOARD
BUTTON BUTTON RY-22
2

LATCH -28 V,
RELAY

Page 13E
SECTION E -
5. T h e COIN REGISTER MECHANISM CANCEL SOLENOID and the SELECTOR SWITCH COUNTER
a r e energized as the SHAFT and MAGNET ARM ASSEMBLY r o t a t e s . The number of credits
-
cancelled is determined by the placement of bridging s c r e w s on theTOP TUNES OPTION BOARD.

STEPPER I
LATCH
RELAY -28 V,
9-10 83. C.

-
Page 14E WURLITZER
 SECTION

-
WURLITZER Page 1 F
 POWER AND LIGHT SYSTEM

(d) "House" FUSE blown. Check f o r over1

o p e r a t e s normally.

T r a c e a n d r e p a i r , see WIRING DIAGRAMS.

I n s e r t PLUG.

o p e r a t e s normally.

Replace RESISTOR, see page 4E.

 COIN AND CREDIT SYSTEM

SYMPTOMS CAUSE CORRECTIONS

1. Coins rejected o r hang in ( a ) Bind in REJECT ROD ASSEMBLY hole- Remove bind, check f o r damaged p a r t s .
SLUG REJECTOR. ing REJECTOR GATE open.
--- - -=

[;)Dirt in REJECTOR. e a n REJECTOR.

----=-----
ii
See NATIOKAL REJECTORS OPERATION and i
( c ) REJECTOR improperly adjusted, SERVICE MANUAL f o r 01-34 SERTES COlhT 1
SELECTOR.

2. Coins reach COIN BAG but ( a ) COIN MECHANISM CIRCUIT BREAKER Reset CIRCUIT BREAKER; s e e page 3 E .
do not establish c r e d i t s in tripped.
COIN REGISTER MECH-
ANIS M . (b) Open o r burned COIN MAGNET. Replace MAGNET .
( c ) SLUG REJECTOR o r COIN MECHANISM Seat PLUG firmly in socket
PLUG not f i r m l y s e a t e d in socket.

(d) Incorrect alignment of KEJECTOR and Seat REJECTOR properly in MOUNTING

COIN SWITCH PADDLES.

3. Twenty five cent c r e d i t f o r ( a ) Dirty o r incorrectly adjusted 25$ Clean and adjust SWITCH; s e e pages 6A and
two consecutive QUARTERS. CREDIT SWITCH in COIN REGISTER
3E.
MECHANISM .
I (b) Open contacts in RY -8 COIN REGISTER
MECHANISM.
Clean RELAY contacts; s e e page 3 E .
 COON AND CREDIT SYSTEM CONT'D.

SYMPTOMS CAUSE CORRECTIONS

4, Credits established in Clean and adjust KEY SWITCH; s e e pages

) KEY SWITCH open, 7A and 3 E .
COIN REGISTER MECf I A N -
-
---
-.-
ISM; SELECT LAMP does
not light; selections cannot CIeail and adjust SERIES SWITCHES; s e e page
be made. 5 B and 3 E .

( c ) 13 .C, FUSE b!.owr! 111 AMPLIFTER,

.
Replare FUSE Clleclc f o r s h o r t s in D ,C .
circuit, check FUSE f c r proper s i z e .

(d) D i r t y contacts in RY-I o r R-Y-3. Check RELAY contacts; s e e page 3 E and 4E.

(e) TOP TUNE o r STEPPER JUMPER PLUG Replace JUMPER. PLUG; s e e page 4.E.
missing f r o m JUNCTION BOX.

Replace LATCH SOLENOID.

Check BUTTON RELEASE SWITCH; s e e

(g) BUTTON RELEASE SWITCH (n.c .) open. page 4E.

SELECTION SYSTEM

LATCH SOLENOID does

CONTROL SWITCH contacts. pages 4 B and 4E.