Secure I/O 2

INSTALLATION GUIDE
Version 2.11
English

EN 101.00.SIO2 V2.11A
Contents

Safety Instructions ................................................................................ 3

Components .............................................................................................4

Front Side ................................................................................................5

Installation Example ............................................................................. 6

Dimensions ..............................................................................................7

Connections .............................................................................................8
Power .............................................................................................................................................................. 8
RS-485 ............................................................................................................................................................. 8
Relay ............................................................................................................................................................... 9
Fail Safe Lock .......................................................................................................................................... 9
Fail Secure Lock ...................................................................................................................................... 9
Door button ................................................................................................................................................. 10
Door sensor ................................................................................................................................................. 10

Product Specifications ......................................................................... 11

FCC Compliance Information ............................................................. 12

Appendix ................................................................................................13
Disclaimers ................................................................................................................................................... 13
Copyright Notice ......................................................................................................................................... 13
 Safety Instructions

Safety Instructions
Please read the following instructions carefully before using the product. This information is important for ensuring the
safety of the user and for preventing damage to the user's property.

Warning
Violation of the instructions may cause serious injury or death.

Installation Instructions
Do not install the product in direct sunlight or in a location that is damp or dusty.
• This can cause a fire or electric shock.
Do not install the product near any heat source such as electric heaters.
• This can cause a fire from overheat or electric shock.
Install the product in a dry place.
• Moisture can cause product damage or electric shock.
Install the product in a place where there is no electromagnetic interference.
• This can cause product damage or electric shock.
Have qualified service professionals install or repair the product.
• Otherwise, it can cause a fire, electric shock, or injury.
• If the product is damaged due to a user's unauthorized installation or dismantling of the product, a service fee will be
charged for repair.

Caution
Ignoring these instructions may result in minor injuries or damage to the product.

Installation Instructions
Protect the power cord from being walked on or pinched.
• This can cause product damage or injury.
Keep the product away from strong magnetic objects such as magnets, TVs, monitors (especially CRT monitors), or
speakers.
• This can cause a failure.
Secure I/O 2, the electrical locking device and access controller must use independent power source.

Operating Instructions
Do not drop the product or subject it to shock or impact during use.
• This can cause a failure.
Do not press the buttons on the product with excessive force or with a sharp tool.
• This can cause a failure.
Clean the product with a soft, dry cloth. Do not use alcohol, benzene, or water.
• This can cause a product failure.

3
 Components

Components

Bracket Mounting screws for

Secure I/O 2
(2 pcs) bracket
(2 pcs)

120Ω resistor Diode

(1 pc) (1 pc)

NOTE
• Components may vary according to the installation environment.

4
 Front Side

Front Side

LED status indicator for RS-485 D- (TRX-)

LED status indicator for RS-485 D+ (TRX+)

LED status indicator for Power

Power RS-485 D+ (TRX+)

GND RS-485 D- (TRX-)
LED status indicator for External IN 1 RS-485 GND
External IN 1+ Relay Output Normally Closed
External IN GND Relay Output Common
External IN 2+ Relay Output Normally Open
LED status indicator for External IN 2
INIT button:
RESET button
Relay status indication LED

NOTE
• Press INIT button to reset Secure I/O 2 interworking with a device and then connect to another device.

5
 Installation Example

Installation Example
Secure I/O 2 is connected with RS-485 and can be installed anywhere due to its small size. It can be installed with a
junction box or onto a wall control box already installed. It can be installed at the rear side of an Exit button.

RS-485

External input

Relay output

Exit button
Access controller

Door lock device

6
 Dimensions

Dimensions

(Unit: mm)

7
 Connections

Connections
NOTE
• Cable should be AWG22~AWG16.
• To connect the cable to Secure I/O 2, strip off approximately 5~6 mm of the end of the cable and connect them.

Power
• Do not share the power with the access controller.
• If the power is shared by other devices, it should provide 9–18V and a minimum of 500 mA.
• When using a power adapter, it should have IEC/EN 60950-1 certification.

+
DC
power
GND

RS-485
• RS-485 should be twisted pair, and maximum length is 1.2 km.
• Connect a termination resistor (120Ω) to both ends of a RS-485 daisy chain connection. It should be installed at both
ends of the daisy chain. If it is installed in the middle of the chain, the performance in communicating will deteriorate
because it reduces the signal level.

Termination resistor (120Ω)

RS-485 TRX+ RS-485 TRX-

Termination
resistor
GND
(120Ω)

Access controller
Access controller

8
 Connections

Relay

Fail Safe Lock

• To use fail safe lock, connect NC terminal as shown below. Normally, there is a current flowing through the relay and
the door is opened when the relay is activated by blocking current flow. The door will also be opened when there is a
blackout or power failure caused by external conditions.

Deadbolt /
DC power
Door strike

NOTE
• When deadbolt or door strike is installed, the diode included with the product should be connected at both ends of the
power input as shown in the figure. Place the diode carefully in the correct direction. The cathode (stripe mark) should be
connected to the (+) of the power.

Fail Secure Lock

• To use fail secure lock, connect NO terminal as shown below. Normally, there is no current flowing through the relay
and the door is opened when the relay is activated by a current flows. The door is locked when there is a blackout or
power failure caused by external conditions.

Deadbolt /
DC power
Door strike

NOTE
• When deadbolt or door strike is installed, the diode included with the product should be connected at both ends of the
power input as shown in the figure. Place the diode carefully in the correct direction. The cathode (stripe mark) should be
connected to the (+) of the power.

9
 Connections

Door button

GND

RTE button
or
Door button

Door

Door sensor

Door sensor

Door

10
 Product Specifications

Product Specifications
Item Specification

CPU Cortex M 32 MHz

Memory 128 KB Flash + 20 KB RAM

LED 6 LEDs (PWR, RS-485 TX/RX, IN1, IN2, Relay)

Input/Output terminal Input 2 channels, Relay 1 channel, RS-485 1 channel

Dimensions
36mm x 65mm x 18mm
(Width x Height x Depth)

Power • Recommended: 9 VDC (130 mA), 12 VDC (100 mA), 18 VDC (70 mA)
• Maximum: 18 VDC (200 mA)
• Current: Maximum 200 mA
Relay • Voltage: Max. 24 VDC
• Current: 0.5A, Max. 1A

11
 FCC Compliance Information

FCC Compliance Information

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment
under FCC rules.

12
 Appendix

Appendix

Disclaimers
• This document provides the information pertaining to Suprema's products.
• The right of use is granted only to the products that are covered by the sales agreement and conditions guaranteed by
Suprema. Any license of intellectual property that is not dealt within this document is not granted.
• Suprema does not provide any warranty or liability of fitness or merchantability for a particular purpose and of
infringement of patents, copyrights, or other intellectual properties, regarding the sales or use of Suprema's products.
• Do not use Suprema's products in either circumstances where people could be hurt or die as a consequence of
malfunctions of the products or circumstances related to medical treatments, the rescue of lives, or life supports. If a
user suffers an accident in one of the circumstances mentioned above, employees, subsidiaries, branches, partners,
and distributors of Suprema are exempt from liability even when it is claimed that there is a significant fault in the
design or production process, and also they are not liable for any direct or indirect cost or expenditure including legal
costs.
• Suprema can change the standard and specification of its products anytime without notice in order to improve the
stability, functions, or design of the products. Designers should keep in mind that the functions or explanations
denoted as "to be implemented" or "not defined" can be changed anytime. Suprema will implement or define such
items in the shortest possible time, and will not accept any liability for problems incurred including compatibility issues.
• Contact Suprema, sales representatives of Suprema, or local distributors in order to get the latest specifications before
ordering products.

Copyright Notice
Suprema has the copyright of this document. The rights of other product names, brands, and trademarks belong to
individuals or organizations who own them.

13
Suprema Inc.
17F Parkview Tower, 248, Jeongjail-ro, Bundang- gu, Seongnam-si, Gyeonggi-do, 13554, Rep. of KOREA
Tel: +82 31 783 4502 I Fax: +82 31 783 4503 I Inquiry: [email protected]
©2020 Suprema Inc. Suprema and identifying product names and numbers herein are registered trade marks of Suprema, Inc. All non-Suprema brands and product names are
trademarks or registered trademarks of their respective companies. Product appearance, build status and/or specifications are subject to change without notice.