Scribd
Upload
40 views1 page

BrazeTec 4076

BrazeTec 4076 is a low melting silver-based brazing alloy with a nominal composition of Ag 40, Cu 30, Zn 28, and Sn 2, suitable for brazing various metals including steels and copper alloys. It has a melting range of approximately 650 - 710°C and offers good tensile and shear strength, making it ideal for applications in the automotive and electric industries. The product is available in various forms such as wire, rods, ribbon, and preforms, with specific delivery options upon request.

Uploaded by

Amir Suljanovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
40 views1 page

BrazeTec 4076

BrazeTec 4076 is a low melting silver-based brazing alloy with a nominal composition of Ag 40, Cu 30, Zn 28, and Sn 2, suitable for brazing various metals including steels and copper alloys. It has a melting range of approximately 650 - 710°C and offers good tensile and shear strength, making it ideal for applications in the automotive and electric industries. The product is available in various forms such as wire, rods, ribbon, and preforms, with specific delivery options upon request.

Uploaded by

Amir Suljanovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

TD-STM-BT-E-0006-00

Technical Data Sheet BrazeTec 4076

Standard
ISO 17672 Ag 140
(DIN EN 1044) (AG 105)
(AWS 5.8) (BAg-28)

Nominal composition [wt.-%] Ag 40; Cu 30; Zn 28; Sn 2


Permitted impurities max. [wt.-%] Al 0.001; Bi 0.030; Cd 0.010; P 0.008; Pb 0.025; Si 0.05
Max. impurities [wt.-%] 0.15

Technical data
Melting range acc. ISO 17672 approx. 650 - 710°C
Melting range acc. Measurement approx. 665 – 725°C (DSC –measurement)
Brazing temperature approx. 725°C
Density approx. 9.0 g/cm³
Tensile strength acc. DIN EN 12797 with S235: 350 MPa; with E295: 430 MPa
Shear strength acc. DIN EN 12797 with S235: min 150 MPa
Elongation approx. 20 %
Electrical Conductivity approx. 11 m/ mm²
Operating temp. of brazed joint approx. -200°C to +200°C (without loss in strength)

Standard delivery forms*


Wire: 1.0 - 1.5 - 2.0 mm Ø
Rods: 1.0 - 1.5 - 2.0 mm Ø, 500 mm length
Ribbon: 0.1/ 0.2/ 0.3/ 0.4 mm thickness and 70 mm width
Preforms: rings, shaped parts, sections, stamped and shaped parts,
shims, discs, perforated plates
*Other delivery forms upon request

Applications
BrazeTec 4076 is a low melting silver based brazing alloy with excellent flow characteristics. It can be
used for brazing any steels, copper and copper based alloys as well as for nickel and nickel based
alloys.
It can be used for brazing with flame or induction brazing procedures.
Typical applications are found e.g. in automotive and in the electric industry.

Details in product brochures or other advertisements about our products, equipment, plant and processes are based on our research and our
experience in the f ield of applied engineering and are merely recommendations. It is not possible to infer any warranted qualities or warranted use
f rom these details, unless they were expressly agreed as a warranted quality. We reserve the right to make technical modifications in the course
of our product development.
The user must verify the suitability of our products and processes for the use or application intended by him on his own responsibility. This shall
also apply to the protection of third party property rights as well as to applications and processes. The properties of samples and specimens are
binding only if these have been expressly agreed to define the quality of the goods. Information on the quality and durability and other particulars
are warranted only if these are agreed and designated as such. The specifications agreed with the user/purchaser in writing are relevant for the
quality of the goods and if specifications have not been agreed in writing, the information contained in our technical data s heets, specifications or
drawings.
Any additional or diverging agreements on the quality must be in writing. Any suitability of the product for the presupposed or customary use
which supplements or diverges from the agreed quality is out of the question. Our General Conditions of Sale and Delivery shall apply; the current
v ersion is available at http://www.saxonia-tm.de/en/TechnicalMaterials/agbs/.

Druckdatum: 16.08.2018 Seite 1 von 1

You might also like