CK-1.

00USD0408
Series K
(Helical Bevel)

Technical
Up to - 120 HP / 109,000 lb.in

GEAR MOTORS
www.davidbrown.com
 SERIES K
PRODUCTS IN THE RANGE
Serving an entire spectrum of mechanical drive applications from food, energy, mining and metal; to automotive,
aerospace and marine propulsion, we are here to make a positive difference to the supply of drive solutions.

Series A Series B Series BD HTP Series BS Series C

Worm Gear units Conex helicoidal Screwjack worm High torque Worm gear unit Right angle drive
and geared motors gear geometry right gear unit planetary gear units helical worm geared
in single & double angle gearmotors motors & reducers
reduction types and reducers

DuoDrive Series E Extruder Drive Series F Series G Series H

Dual gears on Economical Rugged duty Parallel angle Helical parallel shaft Large helical
parallel output planetary servo reducer takes high helical bevel helical & bevel helical right parallel shaft &
shafts gearboxes screw pressure geared motors & angle drive gear bevel helical right
reducers units angle drive units

Series J Series K Series M Series P Roloid Gear Pump Series W

Shaft mounted Right angle helical In-line helical Precision planetary Lubrication and fluid Precision right angle
helical speed bevel helical geared geared motors & servo gearboxes transportation pump servo gearboxes
reducers motors & reducers reducers

Series X Series X Series X Series X Series X We offer a wide range

Cone Ring Gear Grid Nylicon Torque Limiter of repair services and
Pin and bush Torsionally rigid, Double flexing steel Gear coupling with Overload protection many years experience of
elastomer coupling high torque coupling grid coupling nylon sleeve device repairing demanding and
highly critical transmissions
in numerous industries.

We can create custom engineered transmission solutions of any size and configuration.
 ATEX
Compliance Assured

Total compliance with the ATEX Directive safeguarding the use of

industrial equipment in potentially explosive atmospheres is
assured for users of our geared products.

Certification is available for standard gearboxes and geared

motors with badging displaying the CE Mark and the Ex mark,
name and location of the manufacturer, designation of series or
type, serial number, year of manufacture, Ex symbol and
equipment group/category.

ATEX directive 94/9/EC (also known as ATEX 95 or ATEX 100A)

and the CE Marking Directive are enforced in all EC member
states. Compliance is compulsory for designers, manufacturers or
suppliers of electrical and non-electrical equipment for use in
potentially explosive atmospheres created by the presence of
flammable gases, vapours, mists or dusts.

Ex compliant standard gearboxes can be supplied against Groups

2 or 3 for surface industries in designated hazardous location
Zones 1 and 2 for gases, vapours and mists; and in Zones 21 and
22 for dusts.
 SERIES K
CONTENTS
General Description 1
Unit Designations 2
Explanation and use of Ratings and Service Factors 3
Load Classification by Applications 4
Selection Procedure For Motorized Units 5-6
Output Options 7-8
Motor Adaptors 9 - 10
INSTALLATION, MAINTENANCE, LUBRICATION
Installation and Maintenance 12 - 14
Lubrication 15 - 16
Starting/Operation Instructions 17
Mounting Positions 18
Plug Positions 19
Unit Handings 20
Shaft Alignment 21
Alternative Shaft Fixing Methods 22
Taper Release Bushing Installation 23
Shrink Disc Installation And Maintenance 24
MOTORIZED
Motor Details 26
Additional Motor Features 27
Additional Gearbox Features 28
Exact Ratios 29 - 30
Selection Tables Geared Motors 31 - 60
Dimension Sheets - Geared Motors 61 - 63
Motorized Backstop Module 64
REDUCER
Overhung & Axial Loads on Shafts 66
Reduction Ratings 67 - 76
Dimension Sheets - Geared Motors 67 - 68
Thermal Power Ratings 69
Fan Cooled Units 70
Reducer Backstop Module 71
OUTPUT OPTIONS
Dimensions of Outputshaft Options 82
Shrink Disc 83
Dimensions Taper Release Bushing 84 - 85
Dimensions Torque Bracket 86
Dimensions All Units 87 - 88
Dimensions Sheet - Assembly / Disassembly 89 - 90

Shipping Specification 91
 SERIES K
GENERAL DESCRIPTION

Series K
Series K right angle drive helical bevel helical geared motors
offer ratios from 8 : 1 to 160 : 1 in three stages or up to 7,100 : Motorized Triple Reduction
1 in five stages. Motors are available up to 100 HP and output Standard Unit With Feet
torque capacity up to 100,000 lb.in.

The Series K geared motor is designed with integral cast feet

for base or end mounting and can be offered with single or
double extended output shafts. Units are also available shaft
mounted or with output flanges and are available for mounting * K 0 8 3 2 5 0 . B M C - 1 B 7 . 5 A - -
horizontally or vertically. The units can also be offered with a
bolt on torque reaction bracket and all variants are available
either Motorized or with an input shaft assembly.

Adding to the range of geared motors this product takes Reducer Quintuple Reduction
advantage of our many years of accumulated design Standard Unit With Feet
expertise together with the use of high quality materials and
components. The end result is a series of speed reducing
geared motors offering high load carrying capacities, increased
efficiency, quiet running and reliability.

The range includes: * K 0 8 5 2 1 2 C B R C - 1 - - - - - - -

9 sizes of unit
K03, K04, K05, K06, K07, K08, K09, K10 and K12.

Version B - standard unit with feet

Version F or H - standard unit with output flange Reducer Triple Reduction Standard
Version T or Q - standard unit with torque bracket Unit With Output Flange On Left
Unit Types:

Unit type M - Motorized with IEC standard motor

Unit type N - Motorized with NEMA standard motor
Unit type H - Motorized with high efficiency motor (EFF1 or
EPACT) *
Unit type E - Motorized with NEMA high efficiency motor K 0 9 3 1 5 0 . F R H - 1 - - - - - - -
(EPACT)
Unit type G - Unit to allow fitting of IEC motor

Unit type A - Unit to allow fitting of NEMA motor

Motorized Quintuple Reduction
Unit type R - Reducer unit Standard Unit With Feet
Unit type S - Reducer unit with fan kit
Unit type W - Reducer unit with backstop CCW rotation
Unit type X - Reducer unit with backstop CW rotation
Unit type Y - Reducer unit with fan and backstop CW rota-
tion
Unit type Z - Reducer unit with fan and backstop CCW rota-
tion
* K 0 8 5 2 1 2 C B M C - 1 B . 2 5 A - -
Design Features Include:
Patented standard motor connection (IEC or NEMA)
Ability to fit double oil seals, on output shaft or reducer input Reducer Triple Reduction
shaft as required. Standard Unit With Feet
All units are dimensionally interchangeable with other major
European manufacturers

Braked geared motors are available as standard

Units are manufactured and assembled from a family of * K 0 8 3 2 5 0 . B R C - 1 - - - - - - -

modular kits for distributor friendliness minimising inventory
and maximising availability

Motorized units can be fitted with a backstop module and

reducer units can be fitted with a backstop and fan.
Reducer Triple Reduction Standard
As improvements in design are being made continually this Unit With Torque Bracket
specification is not to be regarded as binding in detail and
drawings and capacities are subject to alteration without
notice. Certified drawings will be sent on request.

* K 0 8 3 2 5 0 . T R H - 1 - - - - - - -

* Typical unit designations


 SERIES K
UNIT DESIGNATIONS
Gearbox Codes Motor Codes
**Looking on Inputshaft Mounting posi-

Additional Gearbox Features

tion 1 (See page 18 for unit handings)

Additional Motor Features

** Non Standard Handing - Consult Ap-

Nominal Overall Ratio

Geared Motor Power

plication Engineering

No of Motor Poles
Mounting Position
No of Reductions
*** Standard Handing

Revision Version

Motor Adaptor
Output Shaft
Unit Version
Type of Unit
Size of Unit
Series

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 - Additional Gearbox Features

Double Oil Seal, Motorized Backstop
* K
etc
Example K 0 8 3 2 5 0 . B N N Q 1 D 7 . 5 B - -
e.g. - F See Page 27

1 - Series K 19 - Additional Motor Features

Range K e.g. - A See Page 28

2, 3 - Size of Unit For Types Without Motor Enter -

0 3 Through 1 2
18 - No of Motor Poles

4 - No of Reductions - No motor
60 Hz 50 Hz
3 Through 5
4 Pole (Std) 1800 rpm B 1500 rpm A
5 - Revision Version
4 Pole (High)1800 rpm L 1500 rpm K
2 For Sizes 03 to 08
6 Pole (Std) 1200 rpm D 1000 rpm C
1 For Sizes 09 to 12
6 Pole (High)1200 rpm N 1000 rpm M
6, 7, 8 - Nominal Overall Ratio 2 Pole 3600 rpm F 3000 rpm E

e.g. 5 0 . 8 Pole 900 rpm H 750 rpm G

S Dual speed or special motor

9 - Unit Version

Standard Unit with Feet B 15, 16, 17 - Geared Motor Powers

STD Unit with Output Flange F on Left ** H on Right ** Motor HP required (For 50 Hz enter kW)

STD Unit with Torque Bracket T on Left ** Q on Right ** e.g. . 7 5

10 - Type of Unit For reducer and non standard

N - Motorized with NEMA standard motor motor types enter - - -

M - Motorized with IEC standard motor

13, 14 - Mounting Position
E - Motorized with NEMA high efficiency motor (EPACT)
e.g. 2 B See Page 18
H - Motorized with IEC high efficiency motor (EFF1 or EPACT)

G - Unit to allow fitting of IEC motor (non customer motor) 12 - Motor Adaptor For Unit Types
Column 10 Entries M, N, H, E, G or A
A - Unit to allow fitting of NEMA motor (non customer motor) See Pages 9 and 10

R - Reducer unit For All Other Types Enter -

S - Reducer unit with fan kit 11 - OUTPUT SHAFT

W - Reducer unit with backstop CCW rotation Inch Single Extension N on Left ** B on Right **

X - Reducer unit with backstop CW rotation Inch Double Extension P

Y - Reducer unit with fan and backstop CW rotation Inch Hollow Shaft A

Z - Reducer unit with fan and backstop CCW rotation Inch Taper Release Z on Left ** S on Right ***

Shrink Disc M on Left ** U on Right ***

* This Page May Be Photocopied Allowing The Customer To Enter Their Order
To access the on line configurator please visit www.swift-gears.com for a hard copy version authorised distributors can visit www.swiftdistributors.com
and view our Engineering Document ENG 07-01-014.

 SERIES K
EXPLANATION & USE OF
RATINGS & SERVICE FACTORS
Gear unit selection is made by comparing actual loads with catalogue ratings. Catalogue ratings are based on a standard set of loading
conditions, whereas actual load conditions vary according to type of application. Service Factors are therefore used to calculate an equivalent
load to compare with catalogue ratings.

i.e. Equivalent Load = Actual Load x Service Factor

Mechanical ratings and service factors Fm and Fs

Mechanical ratings measure capacity in terms of life and/or strength, assuming 10 hr/day continuous running under
uniform load conditions.

Catalogue ratings allow 100% overload at starting, braking or momentarily during operation up to 10 hours per day.

The unit selected must therefore have a catalogue rating at least equal to half maximum overload.

Mechanical Service Factor Fm (Table 1) is used to modify the actual load according to daily operating time, and type of loading.

Load characteristics for a wide range of applications are detailed in Table 3 opposite, which are used in deciding the
appropriate Service Factor Fm from Table 1.

If overloads can be calculated, or accurately assessed, actual loads should be used instead of Fm.

For units subjected to frequent stop/starts overloads in excess of 10 times/day multiply factor Fm x Factor Fs (table 2).

For applications where units are to operate in extremely dusty or moist/humid atmospheres unit selection should be referred to application
engineering.

Table 1. Mechanical Service Factor (Fm)

Duration of Load classification-driven machine

Prime mover service- hrs Uniform Moderate Heavy
per day
mass acceleration mass acceleration mass acceleration
factor < 0.2 factor < 3 factor < 10
Under 3 0.80 1.00 1.50
Electric motor, steam
turbine or hydraulic motor 3 to 10 1.00 1.25 1.75

Over 10 1.25 1.50 2.00

Under 3 1.00 1.25 1.75

Multi-cylinder internal
combustion engine 3 to 10 1.25 1.50 2.00

Over 10 1.50 1.75 2.25

Under 3 1.25 1.50 2.00

Single cylinder internal
combustion engine 3 to 10 1.50 1.75 2.25

Over 10 1.75 2.00 2.50

Mass acceleration factor = all external moments of inertia * * calculated with reference to
moment of inertia of driving motor the motor speed

Table 2. Number of Starts Factor (Fs)

Start / Stops Up to
5 10 40 60 > 200
per hour (1) 1

Factor Fs 1.00 1.03 1.06 1.10 1.15 1.20

Note: (1) Intermediate values are obtained by linear interpolation


 SERIES K
LOAD CLASSIFICATION
BY APPLICATIONS
Driven Machine type of Driven Machine type of Driven Machine type of
load load load

Table 3 Cranes
main hoists
log haul-incline
log haul-well type
H
H
log haul
presses
H
M
bridge travel log turning device H pulp machine reel M
trolley travel main log conveyor H stock chest M
U = Uniform load off bearing rolls M suction roll M
Crusher planer feed chains M washers and thickeners M
M = Moderate shock load ore H planer floor chains M winders M
stone H planer tilting hoist M
sugar H re-saw merry-go-round Printing presses
H = Heavy shock load conveyor M
Dredges roll cases H Pullers
= Refer to cable reels M slab conveyor H barge haul H
conveyors M small waste
Application Engineering cutter head drives H conveyor-belt U Pumps
jig drives H small waste centrifugal U
maneuvering winches M conveyor-chain M proportioning M
pumps M sorting table M reciprocating
screen drive H tipple hoist conveyor M single acting; 3 or
stackers M tipple hoist drive M more cylinders M
utility winches M transfer conveyors M double acting; 2 or
transfer rolls M more cylinders M
type of Dry dock cranes tray drive M single acting; 1 or 2
Driven Machine trimmer feed M cylinders
load main hoist
auxiliary hoist waste conveyor M double acting; single
boom, luffing cylinder
Agitators rotating, swing or slew Machine tools rotary
pure liquids U tracking, drive wheels bending roll M gear type U
liquids and solids M punch press-gear driven H lobe, vane U
liquids-variable density M Elevators notching press- belt
bucket-uniform load U driven Rubber and plastics
Blowers bucket-heavy load M plate planers H industries
centrifugal U bucket-continuous U tapping machine H crackers H
lobe M centrifugal discharge U other machine tools laboratory equipment M
vane U escalators U main drives M mixed mills H
freight M auxiliary drives U refiners M
Brewing and distilling gravity discharge U rubber calenders M
bottling machinery M man lifts Metal mills rubber mill-2 on line M
brew kettles-continuous passenger draw bench carriage rubber mill-3 on line M
duty M and main drive M sheeter M
cookers-continuous duty M Fans pinch, dryer and tire building machines
mash tubs-continuous centrifugal U scrubber rolls-reversing tire and tube press
duty M cooling towers slitters M openers
scale hopper-frequent induced draft table conveyors tubers and strainers M
starts M forced draft non-reversing warming mills M
induced draft M group drives M
Can filling machines M large, mine, etc M individual drives H Sand muller M
large, industrial M reversing
Cane knifes M light, small diameter U wire drawing and Sewage disposal
flattening machine M equipment
Car dumpers H Feeders wire winding machine M bar screens U
apron M chemical feeders U
Car pullers M belt M Mill-rotary type collectors U
disc U ball H dewatering screws M
Clarifiers U reciprocating H cement kilns H scum breakers M
screw M dryers and coolers H slow or rapid mixers M
Classifiers M kilns, other than cement H thickeners M
Food industry pebble H vacuum filters M
Clay working beef slicer M rod
machinery cereal cooker U plain H Screens
brick press H dough mixer M wedge bar H air washing U
briquette machine H meat grinders M tumbling barrels H rotary-stone or gravel M
clay working machinery M travelling water intake U
pug mill M Generators-not Mixers
welding U concrete mixers Slab pushers M
Compressors -continuous M
centrifugal U Hammer mills H concrete mixers Steering gear
lobe M -intermittent M
reciprocating Hoists constant density U Stokers U
multi-cylinder M heavy duty H variable density M
single cylinder H medium duty M Sugar industry
skip hoist M Oil industry cane knives M
Conveyors-uniformly chillers M crushers M
loaded or fed Laundry washers oil well pumping mills M
apron U reversing M paraffin filter press M
assembly U rotary kilns M Textile industry
belt U Laundry tumblers M batchers M
bucket U Paper mills calenders M
chain U Line shafts agitators, (mixers) M cards M
flight U driving processing barker-auxiliaries- dry cans M
oven U equipment M hydraulic M dryers M
screw U light U barker-mechanical H dyeing machinery M
other line shafts U barking drum H knitting machines
Conveyors-heavy beater and pulper M looms M
duty not uniformly Lumber industry bleacher U mangles M
fed barkers-hydraulic- calenders M nappers M
apron M mechanical M calenders-super H pads M
assembly M burner conveyor M converting machine, range drives
belt M chain saw and drag saw H except cutters, platers M slashers M
bucket M chain transfer H conveyors U soapers M
chain M craneway transfer H couch M spinners M
flight M de-barking drum H cutters-plates H tenter frames M
live roll edger feed M cylinders M washers M
oven M gang feed M dryers M winders M
reciprocating H green chain M felt stretcher M
screw M live rolls H felt whipper H Windlass
shaker H log deck H jordans M


 SERIES K
SELECTION PROCEDURE
FOR Motorized UNITS
EXAMPLE APPLICATION DETAILS

Absorbed power of driven machine = 17HP

Output speed of gearbox or Input speed of machine = 45rev/min
Application = Uniformly loaded belt conveyor
Duration of service (hours per day) = 24hrs
Mounting position = 1
Ambient temperature = 68oF
Running time (%) = 100%

1 DETERMINE MECHANICAL SERVICE FACTOR (Fm)

Refer to Load Classification by Application, table 3, page 4

Application = Uniformly loaded belt conveyor

Conveyors-uniformly
loaded or fed
U = Uniform load
apron U
assembly U
belt U
bucket U
chain U
Refer to mechanical service factor (Fm), table 1, page 3
Duration of service (hours per day) = 24hrs

Duration of Load classification-drive

Prime mover service- Moderate
hrs per day Uniform 2 DETERMINE REQUIRED OUTPUT TORQUE
Shock
AT GEARBOX OUTPUTSHAFT
Electric motor, Under 3 0.80 1.00
steam turbine Absorbed = Absorbed power x 63025
3 to 10 1.00 1.25 output torque Gearbox output speed
or
hydraulic motor Over 10 1.25 1.50 17 x 63025 = 23810 lb.in
45
Therefore mechanical service factor (Fm) = 1.25

3 SELECT GEARED MOTOR

Refer to selection table one motor size larger than absorbed power.
Absorbed power = 17 HP, therefore refer to 20 HP selection table, page 53
Required output speed of gearbox = 45 rev/min

N2 lb
20 HP R/MIN
i
in
Fm lbf UNIT DESIGNATION lb
Overhung

Column Entry 1 Through 20

Service
Torque
Output

Output

Weight
Speed

Frame
Factor

Motor
Ratio

Load

Spaces to be filled when entering order

Size

4 POLE 118 14.94 10259 3.09 7386 K 0 9 3 1 1 6 . _ N _ _ _ _ 2 0 . B - - 666 256TC

98 17.93 12325 2.43 7354 1 8 .
88 20.03 13759 2.23 7437 2 0 .
81 21.61 14830 2.39 7447 2 2 .
73 24.14 16568 2.18 7431 2 5 .
63 27.78 19123 1.73 7477 2 8 .
56 31.67 21797 1.53 7643 3 2 .
53 33.47 22927 1.63 7643 3 6 .
46 38.16 26187 1.42 7643 4 0 .
39 44.89 30815 1.09 7643 4 5 .

Go to point 4


 SERIES K
SELECTION PROCEDURE
FOR MOTORIZED UNITS

4 CHECK OUTPUT TORQUE

Output torque (M2) of selected unit must be equal or more than required output torque at gearbox outputshaft.
Required output torque at gearbox outputshaft = 23810 lb.in

N2 lb
20 HP R/MIN
i
in
Fm lbf UNIT DESIGNATION lb

Overhung
Column Entry 1 Through 20

Service
Torque
Output

Output

Weight
Speed

Frame
Factor

Motor
Ratio

Load
Spaces to be filled when entering order

Size
4 POLE 118 14.94 10259 3.09 7386 K 0 9 3 1 1 6 . _ N _ _ _ _ 2 0 . B - - 666 256TC
98 17.93 12325 2.43 7354 1 8 .
88 20.03 13759 2.23 7437 2 0 .
81 21.61 14830 2.39 7447 2 2 .
73 24.14 16568 2.18 7431 2 5 .
63 27.78 19123 1.73 7477 2 8 .
56 31.67 21797 1.53 7643 3 2 .
53 33.47 22927 1.63 7643 3 6 .
46 38.16 26187 1.42 7643 4 0 .
39 44.89 30815 1.09 7643 4 5 .

5 CHECK SERVICE FACTOR

Service factor (Fm) of selected unit must be equal or more than required service factor.
Required service factor of gearbox = 1.25

N2 lb
20 HP R/MIN
i
in
Fm lbf UNIT DESIGNATION lb
Overhung

Column Entry 1 Through 20

Service
Torque
Output

Output

Weight
Speed

Frame
Factor

Motor
Ratio

Load

Spaces to be filled when entering order

Size
4 POLE 118 14.94 10259 3.09 7386 K 0 9 3 1 1 6 . _ N _ _ _ _ 2 0 . B - - 666 256TC
98 17.93 12325 2.43 7354 1 8 .
88 20.03 13759 2.23 7437 2 0 .
81 21.61 14830 2.39 7447 2 2 .
73 24.14 16568 2.18 7431 2 5 .
63 27.78 19123 1.73 7477 2 8 .
56 31.67 21797 1.53 7643 3 2 .
53 33.47 22927 1.63 7643 3 6 .
46 38.16 26187 1.42 7643 4 0 .
39 44.89 30815 1.09 7643 4 5 .

6 CHECK OVERHUNG LOADS

If sprocket, gear, etc is mounted on the outputshaft then refer to Overhung Loads Procedure, page 65, and compare
with allowable overhung load (N) of selected unit
Allowable overhung load (N) must be equal or more than calculated overhung load (P)

N2 lb
20 HP R/MIN
i
in
Fm lbf UNIT DESIGNATION lb
Overhung

Column Entry 1 Through 20

Service
Torque
Output

Output

Weight
Speed

Frame
Factor

Motor
Ratio

Load

Spaces to be filled when entering order

Size

4 POLE 118 14.94 10259 3.09 7386 K 0 9 3 1 1 6 . _ N _ _ _ _ 2 0 . B - - 666 256TC

98 17.93 12325 2.43 7354 1 8 .
88 20.03 13759 2.23 7437 2 0 .
81 21.61 14830 2.39 7447 2 2 .
73 24.14 16568 2.18 7431 2 5 .
63 27.78 19123 1.73 7477 2 8 .
56 31.67 21797 1.53 7643 3 2 .
53 33.47 22927 1.63 7643 3 6 .
46 38.16 26187 1.42 7643 4 0 .
39 44.89 30815 1.09 7643 4 5 .

NOTE: If any of the following conditions occur then consult Application Engineering:-
a) Inertia of the Driven Machine (Referred to motor speed) >10 b) Ambient temperature is above 104oF
Inertia of Gear Unit plus Motor


 SERIES K
OUTPUT OPTIONS
OUTPUTBORE OPTIONS,
COLUMN 11 ENTRY Column 11 Entry

Inch Hollow Shaft A

Standard / Inch Hollow Shaft
m1 inch Taper Release * S on Left U on Right

m2 Inch Shrink Disc * M on Left U on Right

Metric Hollow Shaft H

Setscrews
v3 Metric Taper Release * V on Left U on Right
U

øD

Metric Shrink Disc * X on Left Y on Right

m3

T m m
* See pages 83 - 88 for dimensions of these shaft options
Output Shaft Bore

SIZE TYPE COLUMN DIMENSIONS IN INCHES (Metric Bores in mm)

OF OF 11
UNIT BORE ENTRY øD m m1 m2 øm3 T U V3

Inch A 1.251” / 1.250” 2.07” 4.724” 4.13” 1.26” 1.377” 0.250” 3/8” UNF x 2” LONG
K03
Metric H 30.021 / 30.000 52.5 120 105 30.3 33.5 8 M10x50L

Inch A 1.376” / 1.375” 2.60” 5.906” 5.12” 1.38“ 1.525” 0.3125” 1/2” UNF x 21/4” LONG
K04
Metric H 35.025 / 35.000 66 150 132 35.3 38.5 10 M12x55L

Inch A 1.501” / 1.500” 2.87” 6.535” 5.59” 1.51” 1.675” 0.375” 5/8” UNF x 23/4” LONG
K05
Metric H 40.025 / 40.000 73 166 142 40.3 43.5 12 M16x70L

Inch A 1.501” / 1.500” 3.15” 7.087” 6.14” 1.51” 1.51” 0.375” 5/8” UNF x 23/4” LONG
K06
Metric H 40.025 / 40.000 80 180 156 40.3 43.5 12 M16x70L

Inch A 2.001” / 2.000” 3.64” 8.268” 7.20” 2.02” 2.230” 0.500” 5/8” UNF x 23/4” LONG
K07
Metric H 50.025 / 50.000 92.5 210 183 50.5 54 14 M16x70L

Inch A 2.3762” / 2.3750” 4.134” 9.449” 8.268” 2.382” 2.656” 0.625” 3/4” - 16 UNF x 31/4” LONG
K08
Metric H 60.030 / 60.000 105 240 210 60.5 64.5 18 M20x80L

Inch A 2.7512” / 2.7500” 5.217” 11.811” 10.630” 2.772” 3.037” 0.625” 3/4” - 16 UNF x 31/4” LONG
K09
Metric H 70.030 / 70.000 132.5 300 270 70.5 75 20 M20x80L

Inch A 3.2514” / 3.2500” 6.102” 13.780” 12.323” 3.268” 3.591” 0.750” 3/4” - 16 UNF x 31/4” LONG
K10
Metric H 80.030 / 80.000 155 350 313 80.5 85.6 22 M20x80L

Inch A 4.0014” / 4.0000” 7.087” 16.142” 14.685” 4.020” 4.446” 1.000” 1” - 12 UNF x 41/2” LONG
K12
Metric H 100.035 / 100.000 180 410 373 100.5 106.5 28 M24x110L


 SERIES K
OUTPUT OPTIONS
OUTPUTSHAFT OPTIONS,
COLUMN 11 ENTRY Column 11 Entry
Inch Single Extension N on Left B on Right

L11* L12 u Inch Double Extension P

Standard Single Extension C on Left E on Right

Standard Double Extension D

t
Tapped Hole L ød
w

SIZE COLUMN DIMENSIONS IN INCHES (Metric shaft in MM)

TYPE OF
OF 11
OUTPUTSHAFT ød L L11 L12 t u w
UNIT ENTRY
Inch Single Ext. N/B 1.0000” / 0.9995” 1.85” * 1.57” 1.106” 0.25” 3/8 UNF x 0.75” Deep
Inch Double Ext. P 1.0000” / 0.9995” 1.85” * 1.57” 1.106” 0.25” 3/8 UNF x 0.75” Deep
K03
Standard Single Ext. C/E 25.015 / 25.002 47 3 40 28 8 M10 x 1.5 x 22 Deep
Standard Double Ext. D 25.015 / 25.002 47 3 40 28 8 M10 x 1.5 x 22 Deep
Inch Single Ext. N/B 1.2500” / 1.2495” 2.20” * 2” 1.359” 0.25” 1/2 UNF x 1.13” Deep
Inch Double Ext. P 1.2500” / 1.2495” 2.20” * 2” 1.359” 0.25” 1/2 UNF x 1.13” Deep
K04
Standard Single Ext. C/E 30.015 / 30.002 56 3 50 33 8 M12 x 1.75 x 28 Deep
Standard Double Ext. D 30.015 / 30.002 56 3 50 33 8 M12 x 1.75 x 28 Deep
Inch Single Ext. N/B 1.3750” / 1.3745” 2.60” * 2.375” 1.507” 0.3125” 5/8 UNF x 1.5” Deep
Inch Double Ext. P 1.3750” / 1.3745” 2.60” * 2.375” 1.507” 0.3125” 5/8 UNF x 1.5” Deep
K05
Standard Single Ext. C/E 35.018 / 35.002 66 3 60 38 10 M16 x 2 x 36 Deep
Standard Double Ext. D 35.018 / 35.002 66 3 60 38 10 M16 x 2 x 36 Deep
Inch Single Ext. N/B 1.625” / 1.624” 3.00” * 2.375” 1.784” 0.375” 5/8 UNF x 1.5” Deep
Inch Double Ext. P 1.4996” / 1.4990” 3.00” * 2.375” 1.664” 0.375” 5/8 UNF x 1.5” Deep
K06
Standard Single Ext. C/E 40.018 / 40.002 76 3 70 43 12 M16 x 2 x 36 Deep
Standard Double Ext. D 39.991 / 39.975 76 3 70 43 12 M16 x 2 x 36 Deep
Inch Single Ext. N/B 2.000” / 1.999” 3.74” * 2.75” 2.228” 0.50” 5/8 UNF x 1.5” Deep
Inch Double Ext. P 2.000” / 1.999” 3.74” * 2.75” 2.228” 0.50” 5/8 UNF x 1.5” Deep
K07
Standard Single Ext. C/E 50.018 / 50.002 95 3 80 53.5 14 M16 x 2 x 36 Deep
Standard Double Ext. D 49.991 / 49.975 95 3 80 53.5 14 M16 x 2 x 36 Deep
Inch Single Ext. N/B 2.3750” / 2.3740” 4.488” * 3.6875” 2.65” 0.625” 3/4” 16 UNF x 1.65 Deep
Inch Double Ext. P 2.3746” / 2.3739” 4.488” * 3.6875” 2.65” 0.625” 3/4” 16 UNF x 42 Deep
K08
Standard Single Ext. C/E 60.030 / 60.011 114 3 100 64 18 M20 x 2.5 42 Deep
Standard Double Ext. D 59.990 / 59.971 114 3 100 64 18 M20 x 2.5 42 Deep
Inch Single Ext. N/B 2.875” / 2.874” 5.315” * 4.625” 3.20” 0.750” 3/4” 16 UNF x 1.65 Deep
Inch Double Ext. P 2.625” / 2.624” 5.315” * 3.6875” 3.03” 0.625” 3/4” 16 UNF x 42 Deep
K09
Standard Single Ext. C/E 70.030 / 70.011 135 3 110 74.5 20 M20 x 2.5 x 42 Deep
Standard Double Ext. D 69.990 / 69.971 135 3 110 74.5 20 M20 x 2.5 x 42 Deep
Inch Single Ext. N/B 3.625” / 3.624” 6.772” * 5.9375” 4.01” 0.875” 3/4” 16 UNF x 1.65 Deep
Inch Double Ext. P 3.125” / 3.124” 6.417” * 4.625” 3.45” 0.750” 3/4” 16 UNF x 42 Deep
K10
Standard Single Ext. C/E 90.035 / 90.013 172 5 140 95 25 M20 x 2.5 x 42 Deep
Standard Double Ext. D 75.030 / 75.011 163 5 110 79.5 20 M20 x 2.5 x 42 Deep
Inch Single Ext. N/B 4.375” / 4.374” 8.386” * 6.500” 4.81” 1.000” 1” 12 UNF x 2.17 Deep
Inch Double Ext. P 3.875” / 3.874” 7.874” * 6.500” 4.31” 1.000” 1” 12 UNF x 55 Deep
K12
Standard Single Ext. C/E 110.035 / 110.013 213 5 180 116 28 M24 x 3 x 55 Deep
Standard Double Ext. D 95.035 / 95.013 200 5 140 100 25 M20 x 2.5 x 42 Deep

* Inch shaft has an open ended keyway, therefore no 'L11' dimension is required


 SERIES K
MOTOR ADAPTERS
NEMA & IEC
TRIPLE REDUCTION UNITS
NEMA Flanges C Face - Column 12 Entry For Unit Types Column 10 Entries A, E and N Only

UNIT SIZE, NUMBER OF REDUCTIONS, REVISION NUMBER

MOTOR FRAME

K0332 K0432 K0532 K0632 K0732 K0832 K0931 K1031 K1231

FLANGE

COVERAGE
RATIO

112 - 160
25. - 125

36. - 125

28. - 125

28. - 125

25. - 125

36. - 125

45. - 160

45. - 160

45. - 100
8.0 - 20.

8.0 - 32.

8.0 - 25.

8.0 - 25.

8.0 - 20.

8.0 - 32.

8.0 - 40.

8.0 - 40.

8.0 - 40.
56c T U T U - Q - Q - Q - M - - - - - - -
143/145TC V W V W - R - R - R - N - - - - - - -
182/184TC X - X - S T S T S T J P - S - P - N A
COLUMN 12

213/215TC - - - - U - U - U V K Q - T - Q - P B
ENTRY

254/256TC - - - - - - - - W - L U P U L R F Q C
284/286TC - - - - - - - - - - - - Q V M S G R D
324/326TC - - - - - - - - - - - - R W N T H S E
364/365TC - - - - - - - - - - - - - - - - J T -
404/405TC - - - - - - - - - - - - - - - - K U -

IEC Flanges B5 - Column 12 Entry For Unit Types Column 10 Entries G, H and M Only

UNIT SIZE, NUMBER OF REDUCTIONS, REVISION NUMBER

MOTOR FRAME

K0332 K0432 K0532 K0632 K0732 K0832 K0931 K1031 K1231

FLANGE

COVERAGE
RATIO

112 - 160
25. - 125

36. - 125

28. - 125

28. - 125

25. - 125

36. - 125

45. - 160

45. - 160

45. - 100
8.0 - 20.

8.0 - 32.

8.0 - 25.

8.0 - 25.

8.0 - 20.

8.0 - 32.

8.0 - 40.

8.0 - 40.

8.0 - 40.
63 F F - F - V - V - - - - - - - - - - -
71 G G - G - D - D - - - - - - - - - - -
80 A J A J W F W F - F - D - E - - - - -
90 C Q C Q Y H Y H - H - E - F - - - - -
100 - - - - A K A K A K A F - G - E - G N
COLUMN 12

112 - - - - A K A K A K A F - G - E - G N
ENTRY

132 - - - - N P N P C M B G - H - F - H P
160 - - - - - - - - E P C H A J A G A J Q
180 - - - - - - - - - - - - B K B H B K R
200 - - - - - - - - - - - - C L C J C L S
225 - - - - - - - - - - - - D M D K D M T
250 - - - - - - - - - - - - - - - - E U -
280 - - - - - - - - - - - - - - - - F W -

IEC Flanges B14 - Column 12 Entry For Unit Types Column 10 Entries G, H and M Only

UNIT SIZE, NUMBER OF REDUCTIONS, REVISION NUMBER

MOTOR FRAME

K0332 K0432 K0532 K0632 K0732

FLANGE

COVERAGE
RATIO

25. - 125

36. - 125

28. - 125

28. - 125

25. - 125
8.0 - 20.

8.0 - 32.

8.0 - 25.

8.0 - 25.

8.0 - 20.

71 H H - H - E - E - -
COLUMN 12

80 B K B K - G - G - G
ENTRY

90 D R D R Z J Z J - J
100 E S E S B L B L B L
112 E S E S B L B L B L
132 - - - - - - - - D N


 SERIES K
MOTOR ADAPTERS
NEMA & IEC
QUINTUPLE REDUCTION UNITS
NEMA Flanges C Face - Column 12 Entry For Unit Types Column 10 Entries A, E and N Only

UNIT SIZE, NUMBER OF REDUCTIONS, REVISION NUMBER

MOTOR FRAME

K0352 K0452 K0552 K0652 K0752 K0852 K0951 K1051 K1251

FLANGE

COVERAGE

280 & Over

400 & Over

450 & Over

450 & Over

450 & Over

450 & Over

560 & Over

560 & Over

560 & Over

RATIO

125 - 250

125 - 360

125 - 400

125 - 400

125 - 400

125 - 400

160 - 500

160 - 500

160 - 500
56c T U T U T U T U T U - Q - Q - Q - Q
COLUMN 12

143/145TC V W V W V W V W V W - R - R - R - R
ENTRY

182/184TC X - X - X - X - X - S T S T S T S T
213/215TC - - - - - - - - - - U - U - U V U V
254/256TC - - - - - - - - - - - - - - W - W -

IEC Flanges B5 - Column 12 Entry For Unit Types Column 10 Entries G, H and M Only

UNIT SIZE, NUMBER OF REDUCTIONS, REVISION NUMBER

MOTOR FRAME

K0352 K0452 K0552 K0652 K0752 K0852 K0951 K1051 K1251

FLANGE

COVERAGE

280 & Over

400 & Over

450 & Over

450 & Over

450 & Over

450 & Over

560 & Over

560 & Over

560 & Over

RATIO

125 - 250

125 - 360

125 - 400

125 - 400

125 - 400

125 - 400

160 - 500

160 - 500

160 - 500
63 F F F F - F - F - F - V - V - - - -
71 G G G G - G - G - G - D - D - - - -
80 A J A J A J A J A J W F W F - F - F
12 ENTRY
COLUMN

90 C Q C Q C Q C Q C Q Y H Y H - H - H
100 - - - - - - - - - - A K A K A K A K
112 - - - - - - - - - - A K A K A K A K
132 - - - - - - - - - - N P N P C M C M
160 - - - - - - - - - - - - - - E P E P

IEC Flanges B14 - Column 12 Entry For Unit Types Column 10 Entries G, H and M Only

UNIT SIZE, NUMBER OF REDUCTIONS, REVISION NUMBER

MOTOR FRAME

K0352 K0452 K0552 K0652 K0752 K0852 K0951 K1051 K1251

FLANGE

COVERAGE

280 & Over

400 & Over

450 & Over

450 & Over

450 & Over

450 & Over

560 & Over

560 & Over

560 & Over

RATIO

125 - 250

125 - 360

125 - 400

125 - 400

125 - 400

125 - 400

160 - 500

160 - 500

160 - 500

71 H H H H - H - H - H - E - E - - - -
COLUMN 12

80 B K B K B K B K B K - G - G - G - G
ENTRY

90 D R D R D R D R D R Z J Z J - J - J
100 E S E S E S E S E S B L B L B L B L
112 E S E S E S E S E S B L B L B L B L
132 - - - - - - - - - - - - - - D N D N

10
 SERIES K

INSTALLATION,
MAINTENANCE,
LUBRICATION

SERIES K
 SERIES K
INSTALLATION
AND MAINTENANCE
1. GENERAL INFORMATION

The following instructions will help you achieve a satisfactory installation of your Series K unit, ensuring the best possible conditions for a long
and trouble free operation.

All units are tested and checked prior to despatch, a great deal of care is taken in packing and shipping arrangements to ensure that the unit
arrives at the customer in the approved condition.

2. FITTING OF COMPONENTS TO EITHER THE UNIT INPUT OR OUTPUT SHAFT

Shaft diameters below 1.5 inches are held to limits of +0.0000 -0.0005
Shaft diameters of 1.5 and above are held to limits of +0.001 -0.001
Output bore diameter 2 inches and below are held to limits of +0.001 -0.000
Output bore diameters above 2 inches are held to limits of +0.0012 -0.000
Output bore diameters above 3 inches are held to limits of +0.0014 -0.000

- Clean shaft extensions.

- Items (such as gears, sprockets, couplings etc) should not be hammered onto these
shafts since this would damage the shaft support bearings.
- The item should be pushed onto the shaft using a screw jack device fitted into the
threaded hole provided in the end of the shaft.
- Items being fitted may be heated to 176 / 212oF (80 / 100oC) to aid assembly further.

THREADED HOLE DETAILS

UNIT SIZE INPUT SHAFT OUTPUT SHAFT

K0332 1/4 UNF x 0.63 deep 3/8 UNF x 0.75 deep
K0432 1/4 UNF x 0.63 deep 1/2 UNF x 1.13 deep
K0532 1/4 UNF x 0.63 deep 5/8 UNF x 1.5 deep
K0632 1/4 UNF x 0.63 deep 5/8 UNF x 1.5 deep
K0732 5/13 UNF x 0.63 deep 5/8 UNF x 1.5 deep
K0832 3/8 UNF x 0.87 deep 3/4 16 UNF x 1.65 deep
K0931 1/2 UNF x 1.10 deep 3/4 16 UNF x 1.65 deep
K1031 5/8 UNF x 1.42 deep 3/4 16 UNF x 1.65 deep
K1231 3/4 UNF x 1.65 deep 1 12 UNF x 2.17 deep

3. WEATHER PROTECTION OF UNIT

All Series K units are provided with protection against normal weather conditions. Where units are to
operate in extreme conditions, or where they are to stand for long periods without running, eg during
plant construction, we should be notified when ordering so that arrangements for adequate protection
can be made.

12
 SERIES K
INSTALLATION
AND MAINTENANCE
4. INSTALLATION
4.1 MOTORIZED AND REDUCERS (SIZES 03, 04, 05, 06 & 07)

Motorized and Reducer types of sizes 03, 04, 05, 06 & 07 are supplied ready filled with the appropriate amount of lubricant for the
mounting position identified in the original order. (If the unit is to be mounted in a different position to that originally intended then the
amount of lubricant in the unit will require amending

- See Lubrication Section 6 for the revised quantities

- Sizes K06 & K07 have several oil fill and drain plugs to cater for all mounting
positions. See page 19 for plug positions.

MOTORIZED AND REDUCERS (SIZES 08, 09, 10, 13 & 14)

Motorized and Reducer types of sizes 08, 09, 10 & 12 are shipped less oil, for the customer to fill on site once installed. The different
mounting positions are indicated on page 18 with the appropriate oil fill quantities in Lubrication Section 6. The units have several oil
fill and drain plugs to cater for all mounting positions. See page 19 for plug positions.

4.2 FIXING TO CUSTOMER EQUIPMENT

Fixing gear unit flange facings or feet to the customer’s equipment use screws to ISO grade 8.8 minimum.

Torque tighten to:-

Tightening Torque
Screw
Size Holding Down Bolts / Motors to Gearhead
Output Flange Bolts
M6 88 lbf.in 7.3 lbf.ft 88 lbf.in 7.3 lbf.ft
M8 220 lbf.in 18.3 lbf.ft 160 lbf.in 13.0 lbf.ft
M10 450 lbf.in 37.5 lbf.ft 325 lbf.in 27.0 lbf.ft
M12 750 lbf.in 62.5 lbf.ft 570 lbf.in 47.0 lbf.ft
M16 1770 lbf.in 147.5 lbf.ft 1330 lbf.in 110.0 lbf.ft
M20 3100 lbf.in 258.3 lbf.ft 2300 lbf.in 190.0 lbf.ft
M24 5400 lbf.in 450 lbf.ft -
M30 10800 lbf.in 900 lbf.ft -
M36 19000 lbf.in 1585 lbf.ft -

4.3 MOTOR CONNECTIONS

TO MAINS

Connection of the electric motor to the mains supply should be made by a qualified person. The current rating of the motor will be
identified on the motor plate, and correct sizing of the cables to electrical regulations is essential.

MOTOR TERMINAL CONNECTION

Circuit diagrams for the correct wiring of the motor terminal box are supplied with the product.

13
 SERIES K
INSTALLATION
AND MAINTENANCE
4.4 FOOT-MOUNTED UNITS

The following procedure is recommended for all foot mounted units. Foot mounted units are supplied either as free standing units, or if
required, mounted on a standard baseplate with a foot mounted motor correctly aligned and connected by a flexible coupling.

a) Clean shaft extensions and ventilator when fitted.

b) Secure unit, or baseplate if fitted to a rigid foundation using heavy duty bolts to ISO grade 8.8 minimum.
c) Ensure baseplate is not distorted
Note: Units not supplied on baseplates should if possible be mounted on the same bedplate as the prime mover.
d) Align unit (see pages 21)
Note: It is important to ensure when aligning unit on baseplate that all machined mounting points are supported over their full area. If steel
packings are used these should be placed either side of the foundation bolt as close as possible. During the final bolting ensure the unit or
baseplate is not distorted this will cause strains in the gear case resulting in errors of alignment of shafts and gearing.
e) For units mounted on bedplates after alignment select any two diagonally opposite feet, drill ream and dowel in position.
f) Fit guards in accordance with the relevant state and local safety regulations.
g) Check motor wiring for correct direction of rotation this is important when a backstop device is fitted.
h) Fill gear unit with oil (if not factory filled) as detailed in Section 6.

4.5 SHAFT MOUNTED UNITS

The following procedure is recommended for all shaft and foot/shaft mounted units with a standard output bore for other shaft bore options
see page 23, for Taper Release and Page 24 for Shrink Disc.

a) Clean shaft extensions and output line bore of the unit.

b) Spray the gear unit bore with Rocol DFSM anti fretting compound or similar.
b) Locate the unit in position onto the head shaft by the most convenient method shown on Page 22, ensuring it is as close as possible to
the bearing on the driven machine.
c) Anchor the unit to a secure point on the structure by means of the torque arm (reference Page 86 for more detail).
d) Fit guards in accordance with the relevant state and local safety regulations.
e) Check motor wiring for correct direction of rotation this is important when a backstop device is fitted.
f) Fill gear unit with oil (if not factory filled) as detailed in Section 6.

4.6 REPLACEMENT OF OIL SEALS

a) Clean and drain the unit.

b) Remove any equipment from the outputshaft such as couplings and remove the output key.
c) Remove the old seal
d) Smear oil seals with grease (NLGI Grade 2 grease).
e) Fit replacement seal on a seal guide, slide it along the shaft and press the seal into the housings.
f) Fill with the correct amount of an approved lubricant, see Lubrication Section 6.

14
 SERIES K
LUBRICATION
5. LUBRICATION AND MAINTENANCE
5.1 LUBRICATION
Gear units 03, 04, 05, 06 & 07 will be supplied filled with a quantity of EP mineral oil (Grade 6E) appropriate to the intended
mounting position. However if, as requested, the unit is supplied without lubricant then the oil quantity required is obtained
from Table 2. Gear units 08, 09, 10 & 12 are supplied without lubricant (unless factory filled by request). Recommended
lubricants are listed in the Approved Lubricant scheme booklet.

NOTE: Clients wishing to use food compatible or biodegradable lubricants should contact our
Application Engineers for further information.

5.2. PERIODIC INSPECTION

Check oil level every 3000 hours or 6 months whichever is sooner on sizes K06, 07, 08, 09, 10 and 12 and if necessary top
up with the recommended grade of lubricant.

5.3 OIL CHANGES

• Sizes 03, 04 and 05 units are lubricated for life.
• All other sizes of Series K will require an oil change:
- 10,000 hours for mineral oil
- 20,000 hours for synthetic oil

5.4 TEMPERATURE LIMITATIONS

The standard lubricant is suitable for operation in ambient temperatures of 32° to 95°F (0° to 35°C), outside of this consult
Table 1 or our Application Engineers.

TABLE 1 OIL GRADES

AMBIENT TEMPERATURE RANGE

LUBRICANT
Type E 23°F to 68°F 32°F to 95°F 68°F to 122°F
(-5°C to 20°C) (0°C to 35°C) (20°C to 50°C)
Type H -22°F to 68°F
(-30°C to 20°C)

EP Mineral Oil 5E (VG 220) 6E (VG 320) 7E (VG 460)

(type E)

Polyalphaolefin
based Synthetic 5H (VG 220) 5H (VG 220) 6H (VG 320)
with EP additive
(type H)

5.5 GREASE LUBRICATION

Where re-greasing points are provided add 2 shots monthly of NLGI 2 grade grease.

5.6 VENTILATOR
If a ventilator plug is supplied with the unit, remove the filler plug as indicated on page 19, plug positions page, and fit the
ventilator plug in that position.

15
 SERIES K
LUBRICATION
5.7 LUBRICATION QUANTITIES
K03,K04,K05,K06,& K07 Units & Primary Units used for Quintuple Reduction, are supplied factory filled with EP mineral oil
(Grade 6E) appropriate to the intended mounting position. If the unit is supplied without lubricant the unit must be filled with
the the correct lubricant and quantity as listed below.

K08,K09,K10,& K12 Units, require filling with EP mineral oil (Grade 6E)

Lubricant quantities are approximate fill until oil escapes from the level plug hole, fit ventilator plug (when supplied) in the
appropriate position for the required mounting position. If the unit is supplied without lubricant the unit must be filled with the
correct lubricant and quantity.

TRIPLE REDUCTION
Unit K0332 K0432 K0532 K0632 K0732 K0832 K0931 K1031 K1231
Size
1 0.5 0.7 1.1 1.5 2.7 4.4 9.3 15 23

2 0.7 0.9 1.5 1.8 3.6 3.7 8.3 15 27

MOUNTING
POSITION

3 0.8 1.1 1.7 2.8 4.0 7.6 18 28 33

4 1.0 1.3 1.9 2.7 4.5 7.5 17 30 39

5 1.2 1.7 2.5 3.6 5.7 9.6 21 34 50

6 0.9 1.2 2.0 2.6 4.5 7.6 16 25 35

QUINTUPLE REDUCTION

K0352 K0452 K0552 K0652 K0752

Unit Primary Secondary Primary Secondary Primary Secondary Primary Secondary Primary Secondary
Size
M0122 K0332 M0122 K0432 M0322 K0532 M0322 K0632 M0322 K0732

1 0.5 0.5 0.5 0.7 0.8 1.1 0.8 1.5 0.8 2.7

2 0.5 0.7 0.5 0.9 0.8 1.5 0.8 1.8 0.8 2.7
MOUNTING
POSITION

3 0.5 0.8 0.5 1.1 0.8 1.7 0.8 2.8 0.8 2.7

4 0.5 1.0 0.5 1.3 0.8 1.9 0.8 2.7 0.8 2.7

5 0.7 1.2 0.7 1.7 1.1 2.5 1.1 3.6 1.1 5.7

6 1.0 0.9 1.0 1.2 1.4 2.0 1.4 2.6 1.4 4.5

QUINTUPLE REDUCTION..CONT

K0852 K0951 K1051 K1251

Unit Primary Secondary Primary Secondary Primary Secondary Primary Secondary
Size
M0522 K0832 M0522 K0931 M0722 K1031 M0722 K1231

1 1.5 4.4 1.5 9.3 2.6 15 2.6 23

MOUNTING POSITION

2 1.5 3.7 1.5 8.3 2.6 15 2.6 27

3 1.5 7.6 1.5 18 2.6 28 2.6 33

4 1.5 7.5 1.5 17 2.6 30 2.6 39

5 2.0 9.6 2.0 21 3.2 34 3.2 50

6 2.6 7.6 2.6 16 4.7 25 4.7 35

16
 SERIES K
STARTING /OPERATION
INSTRUCTIONS
6. STARTING UP
6.1 PRIOR TO STARTING UP
a) ensure ventilator is fitted (K06 & above)
b) check oil level (K06 & above) top up if necessary
c) ensure all safety devices are in place (ie guards fitted)
d) remove any safety devices fitted to prevent machine rotation

6.2. Starting up should be performed or supervised by suitably qualified personnel

Caution: any deviation from normal operating conditions, (increased temperature, noise, vibrations, power consumption etc) suggest a
malfunction, inform maintenance personnel immediately.

7. OPERATION

7.1 NOISE
The range of Series K product satisfies a noise (sound pressure level) of 85 dB(A) or less when measured at 1 meter from the unit
surface.
Measurements taken in accordance with AGMA 299.01 (B.S.7676 Pt1 : 1993) (ISO 8579-1 : 1993).

7.2 GENERAL SAFETY

Potential hazards which can be encountered during installation, maintenance and operation of drives is covered in greater
detail in the product safety page at the back of this catalog.

Advice is also given on sensible precautions which need to be taken to avoid injury or damage. PLEASE READ !

8. CLEANING
With the drive stationary periodically clean any dirt or dust from the gear unit and the electric motor cooling fins and fan guard to aid
cooling.

Any further information or clarification required may be obtained by contacting us,

Please see our contact details at the back of this booklet.

17
 SERIES K
MOUNTING POSITIONS
COLUMN 13 ENTRY
Enter - for units with no oil fill

Base Mounted Units

6†*

Flange Mounted Units

5†* 3

4
6†*

1
2
* Not Recommended for Geared Motors - Consult Application Engineering

† Gear Units selected for use in mounting positions 5 and 6 should only be used
with overall ratios greater or equal to those shown in the table below

Input Speed (rpm)

5†* 3
Unit Size
< 1000 < 1500 < 1800 > 1800
K03 - KO7 8.0 8.0 8.0
4
K08 8.0 8.0 11.0
Consult
K09 8.0 11.0 14.0 Application
Engineering
K10 11.0 20 25.0
K12 16.0 32 36.0

MOUNTING POSITIONS - SHOWN AS Motorized - APPLIES ALSO FOR REDUCERS

270 o
COLUMN 14 ENTRY

ALL MOTORS Column

Terminal Box Position
14 Entry
A 0o
180 o 0o
B 90o
C 180o
D 270o
- Reducer or no motor fitted

90 o

18
 SERIES K
PLUG POSITIONS

1 2 3

4 5 6

Ventilator / Filling Position

Level Position

Drain Position

19
 SERIES K
UNIT HANDINGS
Column 9 Entry Left Right

Std Unit with F H

Output Flange

Std Unit with

Torque Bracket T Q

Column 11 Metric Inch

Entry Left Right Left Right

Single Output
Shaft C E N B

Double Output
D P
Shaft

Hollow
H A
Shaft

Taper
W
Driven
Z
Driven

Release Machine V Driven

Machine S Driven
Side Side
Machine Machine
Side Side
Note: non-standard handing, Note: non-standard handing,
please contact us please contact us

Shrink X Driven Driven M Driven Driven

Machine Y Machine Machine U Machine
Disc Side Side Side Side

Note: non-standard handing, Note: non-standard handing,

please contact us please contact us

20
 SERIES K
SHAFT ALIGNMENT
Shaft Alignment Figure 1 A B

Errors of alignment fall into categories of angularity (see figure 1) and eccentricity (see
figure 2), or a combination of both.
A
Errors of angularity should be checked for and corrected before errors of eccentricity Figure 2 B

Alignment in accordance with the following procedure will ensure vibration levels meeting
those set out in ISO 10816 Part 1.
Figure 3
Errors of Angularity 1 A B

4 2
If the faces are perfectly true, the angularity can be checked by keeping both shafts
stationary and taking measurements with a block gauge and feelers at the four points 1, 2, 3
and 4 as shown in figure 3. The difference between the readings 1 and 3 will give the error 3
of alignment in the vertical plane, over the length of the shaft equal to the diameter of the Figure 4
coupling flanges, and from this the difference in the relative heights of the feet of the motor
or other connected machine can be found by proportion. Similarly the difference between 1
the readings 2 and 4 gives the amount of sideways adjustment necessary to correct any
errors of alignment in the horizontal plane.
4 2

Generally, however, the coupling faces will not be absolutely true and whilst any errors
so found could be allowed for in checking angularity by the stationary method an easier
method presents itself. This consists
in marking the points 1 on both “A” and “B” and rotating both half couplings, keeping the 3

marked points together. By taking measurements each quarter- Figure 5

1
revolution the errors in the vertical and horizontal planes are again found.

4
TYPE OF ALLOWABLE GAP (G) (Inches 2

COUPLING or mm)

3
Rigid Coupling G = 0.005 D

Please see appropriate installa-

All other types tion and maintenance manual for NOTE: Check the alignment after running the unit
coupling type fitted until it has attained its normal working
temperature. Any discrepancies can then be
NOTE: D is the diameter (Inches or mm) at which the gap is measured. rectified.

Errors of Eccentricity
The procedure for measuring eccentricity is precisely analogous to that used for angularity. In this case, however, the measurements are taken in a
radial direction and the most convenient and accurate means of doing this utilises a dial indicator suitably clamped to one half coupling, and bearing
on the hub or flange of the other, as shown in figures 4 and 5.

Care must, however, be taken to ensure the support for the dial indicator is sufficiently rigid to prevent the weight of the indicator from causing
deflection and, in consequence, inaccurate readings. Extra care should be taken where taper roller bearings are fitted to ensure that alignment is
checked with shafts in mid-point position and a final check made with the unit at operating temperature.

The permitted eccentricity error which can be accommodated in addition to that of the angularity error is
as follows :-
TYPE OF UNIT ALLOWABLE ECCENTRICITY (Inches)
COUPLING SIZE
K03 - K08 0.001
Rigid
K09 - K12 0.001

Please see appropriate installation and

All other types maintenance manual for coupling type
fitted

Special Note Concerning Rigid Couplings

In lining up elements involving rigid couplings it is important that no attempt is made to correct errors of alignment or eccentricity greater than those
above by tightening of the coupling bolts (This applies when the system is cold or at operating temperature). The result is mis-alignment and the
setting up of undue stresses in the shaft, coupling and bearings. This will be revealed by the springing apart of the coupling faces if the bolts are
slackened off. A check on the angularity of a pre-assembled job, after bolting down, can be obtained in the case of rigid couplings by slackening off
the coupling bolts, when any mis-alignment will cause the coupling faces to spring apart. This check may not, however, reveal any strains due to
eccentricity owing to the constant restraint imposed by the spigot.

Series X Couplings
We produce standard flexible couplings to cover the complete range of units, please contact us for details.

21
 SERIES K
ALTERNATIVE SHAFT
FIXING METHODS
SHAFT MOUNT UNITS
ALTERNATIVE SHAFT FIXING METHODS

Shaft Mount Units Retained With A Snap Ring

Shaft Mount Units Retained With A Bolt And Plate

Shaft Mount Units Retained With A Locknut

Shaft Mount Units Retained With A Collar And Set Screw

Shaft Mount Units Retained With A Recessed Plate And Bolt

22
 SERIES K
TAPER RELEASE
BUSHING INSTALLATION
Installation
1) Thoroughly clean and degrease, machine shaft, bushing and gear unit tapered bore using Lowtox or Loctite 7063 Superclean.

Note: the bushing nut threads are coated with anti seize compound at the factory, this should not be removed
(if re-installing previously used nut, re-coat threads with anti-seize compound).

2)

Thin walled bushing Thick walled bushing

Bushing Key (Supplied) Bushing Key (Supplied)

Machine Shaft Machine Shaft

Nut Nut Shaft key (not supplied)

Thin walled bushing (keyway slot through bushing wall)

Slide bushing assembly (bush and nut) onto machine shaft, nut end first, position the keyway slot with keyway in machine shaft (the
bushing may need to be pried open slightly) insert the drive key supplied with the bushing.

Thick walled bushing (with separate internal and external keyways)

Insert key (not supplied) into machine shaft (if shaft has open ended keyway secure key to prevent axial movement) slide bushing
assembly (bush and nut) onto machine shaft, nut end first (the bushing may need to be pried open slightly) insert the drive key supplied
with the bushing

3) Slide gear unit onto driven shaft and bushing taper taking care that key seats into unit keyway, hand Set
tighten nut, (ensure gear unit is in correct axial location) lock the driven shaft and use ‘C’ spanner or Screw
pipe wrench to tighten bushing nut to torque value listed in table 1 below, Do not overtighten. Secure the
bushing nut by locking with setscrew.

Alternative method (only use if torque cannot be measured)

Use wrench to tighten bushing nut gently until the gear unit cannot be moved axially along the shaft by
hand, loosen bushing nut but do not dislodge unit from taper, re-tighten bushing nut by hand, lock the
driven shaft and use ‘C’ spanner or pipe wrench to tighten bushing nut as listed in table 1 below, secure C Spanner
the bushing nut by locking with setscrew.

Vertical Application

If the gear unit is mounted vertically below the driven machine, a shouldered machine shaft together with
a thrust plate and fastener should be used. Secure bushing nut then torque tighten thrust plate fastener
as table 2 below.

Removal

Caution the gear unit must be supported during removal process

1) Loosen setscrew on OD of bushing nut Thrust plate Fastener

2) Use ‘C’ spanner or pipe wrench to remove bushing nut.

Table 1 ‘C’ Spanner wrench type and Table 2 Thrust plate fastener data
bushing nut Tightening Torque (secure fasteners with Loctite 242)
No of turns
Bushing Nut
C’ Spanner (only use if torque Size Fastener Size Torque (Nm)
Size Tightening
Size cannot be
Torque (Nm) measured)
K05 (107)TR 2” - 4 3/4” 1000 1000 K05 (107)TR .500 - 13 UNC 1100 1100
1/4 turn of nut
K06 (115)TR 2” - 4 3/4” 1000 1000 K06 (115)TR .500 - 13 UNC 1100 1100
K07 (203)TR 2” - 4 3/4” 2000 2000 K07 (203)TR .625 - 11 UNC 2190 2190
K08 (207)TR 4 1/2” - 6 1/4” 2000 2000 K08 (207)TR .625 - 11 UNC 2190 2190
K09 (215)TR 4 1/2” - 6 1/4” 3000 3000 1/2 turn of nut K09 (215)TR .875 - 9 UNC 6400 6400
K10 (307)TR 4 1/2” - 6 1/4” 3000 3000 K10 (307)TR 1.00 - 8 UNC 9500 9500
K12 (315)TR 6 1/8” - 8 3/4” 3000 3000 K12 (315)TR 1.00 - 8 UNC 9500 9500

23
 SERIES K
SHRINK DISC INSTALLATION
AND MAINTENANCE
SHAFT MOUNTED UNITS USING A SHRINK DISC DEVICE
INSTALLATION
‘Shrink discs’ can be supplied with shaft mounted units. The following procedures should be followed when fitting or removing units from the driven
shaft.

1 Release locking screws gradually and in succession. Initially a quarter of a turn on each screw will avoid tilting and jamming - do not
remove locking bolts completely.

2 Remove ‘shrink disc’ - from gear unit hollow shaft.

3 Clean and degrease locating diameters of gear unit hollow shaft, driven shaft and ‘shrink disc’ locating diameter on hollow shaft
extension.

4 Draw the gear unit onto the driven shaft (See Figure 3).

5 Grease tapered surfaces of outer ring and inner ring with Molykote 321R or similar.

6 Fit ‘shrink disc’ on gear unit hollow shaft to position shown on Page 83.

7 Tighten all locking screws gradually and in succession. Do not tighten in a diametrically opposite sequence. Several passes are required
until all screws are tightened until the inner and outer ring faces are in-line and the torque figures Ta shown in the table on page 92 are
achieved.

8 Fit protective cover.

Note: When the hollow output shaft is to operate in a vertical position it is essential that the shaft of the driven machine is provided with a
shoulder. When the thrust load is not taken by the shoulder on the driven shaft, an end plate, as shown in Figure 3, must be fitted. It is
recommended that customers’ shafts at the non-clamped end of the sleeve should be coated with Molykote 321R or equivalent.

REMOVAL
1 Removal procedure is similar to the reverse of installation.

Note: Do not remove ‘shrink disc’ locking screws completely.

2 Remove any rust and dirt from gear unit hollow shaft.

3 Withdraw gear unit from driven shaft.

Note: ‘Shrink disc’ should be removed and cleaned thoroughly, and Molykote 321R or similar applied to the tapered surfaces of inner ring
and locking collar before re-use.

Note: Protective covers are supplied with all ‘shrink discs’. Assembly or removal kits and thrust plates are not provided.

Figure 2 Figure 3 Mounting Gear Unit

Shrink
disc
Screws

degreased Nut

Shaft

Gear Unit Jacking

Hollow Shaft screw

Inner ring
end
Driven shaft use
Locking plate
Molykote 321R Unit hollow shaft
collar or similar degreased
(in this area only)

24
 SERIES K

MOTORIZED

SERIES K
 SERIES K
MOTOR DETAILS
NEMA Standard Motors
ko

BF
4 HOLES

øU
øBD øAJ øAK ø øFP
g

AH

MOTOR FRAME BF TAP

Ø BD Ø AJ Ø AK ØU AH CC max Ø FP
SIZE UNC

56C 6.50 5.88 4.5 0.625 2.06 14.12 7.19 3/8 - 16

143TC/145TC 6.50 5.88 4.5 0.875 2.13 14.19 7.19 3/8 - 16

ko

BF
4 HOLES

øU
øBD øAK øAJ ø øFP
g

AH

BF TAP
MOTOR FRAME SIZE Ø BD Ø AJ Ø AK ØU AH CC max Ø FP UNC

182TC/184TC 9.00 7.25 8.5 1.125 2.63 18.05 8.50 1/2 - 13

213TC/215TC 9.00 7.25 8.5 1.375 3.13 21.25 10.19 1/2 - 13

254TC/256TC 10.00 7.25 8.5 1.625 3.75 23.66 12.50 1/2 - 13

284TC/286TC 11.25 9.00 10.5 1.875 4.38 27.76 15.56 1/2 - 13

324TC/326TC 13.38 11.00 12.5 2.125 5.00 30.39 16.94 5/8 - 11

* Motor lengths for our standard motors.

These lengths may vary if alternative motor is fitted.

26
 SERIES K
ADDITIONAL
MOTOR FEATURES
ADDITIONAL MOTOR FEATURES - COLUMN 19 ENTRY

Forced Ventilation/
Hand Release on
Column 19 Entry Brake Motor Constant Blower Thermistors Special
Brake (TECB)

A 
B  
C 
D  
E   
F 
G  
H   
K  
L   
M    
S 

Please refer to our Application Engineers for details of the following additional motor features:
- Wash down
- Customized brake torque
- Seperate brake supply
- Anti Condensation heater
- Bi-metal temperature detectors, Thermostat
- Metal fan cover
- Rain cowl
- Seperate terminal box

27
 SERIES K
ADDITIONAL
GEARBOX FEATURES
ADDITIONAL GEARBOX FEATURES - COLUMN 20 ENTRY

Motorized Backstop***
Column 20 Entry Double Oil* Seals Oil Level** Glass Special****
CW Rotation CCW Rotation

A 
B 
C  
D 
E  
F  
G   
H 
I  
J  
K   
L 

*Double oil seals are for output shafts only. Double oil seals are NOT AVAILABLE on Taper Release output shafts.
**Oil level glass is available on F06-F10. Oil level glass is NOT AVAILABLE on F02-F05 units.
***Limited frame size availability see page 61.

****Please refer to our Application Engineers for details regarding special gearbox features.

28
 SERIES K
EXACT RATIOS
EXACT RATIOS - TRIPLE REDUCTION

Column
Entry
K0332 K0432 K0532 K0632 K0732 K0832 K0931 K1031 K1231
6 7 8

8.0 8.328 8.054 8.112 7.961 8.595 8.128 8.035 8.263 8.513

10. - - - - - - 9.681 9.946 10.26

11. 11.25 11.30 11.41 11.19 11.91 11.52 11.06 11.54 11.80

12. 12.80 12.45 12.78 12.55 13.37 12.80 12.40 12.55 12.96

14. 14.50 14.14 14.35 14.08 14.71 14.24 13.33 13.89 14.21

16. - - - - - - 14.94 15.11 15.61

18. 18.54 17.95 18.22 17.88 19.21 18.41 17.93 18.57 18.20

20. 19.98 20.40 20.66 20.27 21.84 20.67 20.04 20.05 20.17

22. - - - - - - 21.61 22.35 21.93

25. 25.23 25.03 24.64 24.18 26.52 25.34 24.14 24.13 24.29

28. 28.60 27.76 28.37 27.84 29.17 28.56 27.78 29.24 29.00

32. 32.68 31.54 32.99 32.38 33.52 33.24 31.67 33.10 32.83

36. 36.35 35.83 36.91 36.23 38.01 36.88 33.47 35.20 34.93

40. 40.08 39.46 39.34 38.61 41.92 40.36 38.16 39.84 39.55

45. 44.11 45.39 46.63 45.76 48.01 45.66 44.89 45.37 46.81

50. 51.68 49.35 49.78 48.86 54.28 51.54 49.88 50.41 52.76

56. - - - - - - 54.09 54.61 56.39

63. 62.00 59.24 61.78 60.63 62.94 62.48 60.09 60.68 63.57

71. 72.27 71.09 72.85 71.49 75.07 72.86 70.45 71.89 74.62

80. 80.30 80.10 79.77 78.28 82.20 80.03 77.78 82.83 83.10

90. - - - - - - 84.89 86.53 89.89

100 96.70 93.12 97.76 95.93 98.65 98.08 93.71 99.70 100.1

112 110.8 105.7 109.0 106.9 113.5 107.1 107.0 112.0 113.8

125 126.0 120.2 122.2 119.9 126.1 123.3 120.3 120.4 121.1

140 - - - - - - 128.9 134.8 137.1

160 - - - - - - 145.0 144.9 145.9

29
 SERIES K
EXACT RATIOS
EXACT RATIOS - QUADRUPLE REDUCTION

Column Entry
K0352 K0452 K0552 K0652 K0752 K0852 K0951 K1051 K1251
6 7 8

125 128 134 118 116 120 132 - - -

140 145 148 143 140 133 145 - - -

160 165 170 157 154 147 164 161 167 172

200 211 200 208 204 211 203 226 226 238

250 227 258 264 259 233 228 254 260 269

280 287 284 300 294 265 268 282 285 302

320 325 322 316 310 305 297 298 317 332

360 371 355 351 344 374 337 331 373 385

400 413 407 399 391 415 401 402 414 437

450 455 448 453 445 466 462 455 471 493

500 516 508 499 489 513 506 489 515 531

560 568 581 574 563 590 538 563 566 584

630 649 646 624 612 641 641 655 651 671

700 704 712 725 712 737 760 727 723 757

800 798 808 812 797 836 811 789 783 809

900 912 891 899 882 924 888 940 904 946

10C 1015 1000 1045 1026 1062 1007 1028 980 1012

11C 1119 1102 1169 1147 1204 1102 1115 1171 1140

12C 1183 1267 1231 1208 1267 1246 1190 1268 1226

14C 1423 1427 1477 1449 1521 1470 1477 1470 1519

16C 1583 1606 1577 1548 1720 1659 1641 1634 1712

18C 1800 1784 1777 1744 1938 1817 1741 1754 1811

20C 2000 2250 1957 1920 1994 2011 1935 1949 2042

22C 2250 2265 2205 2164 2246 2202 2118 2134 2236

25C 2579 2463 2563 2515 2611 2699 2596 2561 2683

28C 2699 2799 2847 2794 2934 2821 2733 2779 2887

32C 3094 3360 3310 3248 3411 3147 2992 3044 3162

36C 3516 3548 3757 3686 3871 3853 3667 3652 3794

40C 4007 3998 4056 3981 4093 4237 4048 4208 4226

45C 4554 4543 4604 4518 4646 4722 4512 4842 4862

50C 4826 4647 5131 5036 5281 5157 5060 5380 5110

56C 5485 5281 5234 5136 5345 5296 5793 5845 5879

63C 6286 5994 5833 5725 6076 5783 6207 6548 6657

71C 7144 6815 6542 6420 6752 6660 6980 7276 7083

30
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.25 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 73 15.97 908 K 0 3 3 2 8 . 0 _ N _ _ _ _ . 2 5 B - - 55.5 56C
4 POLE 153 11.25 98 13.32 1002 1 1 .
135 12.80 113 12.21 1045 1 2 .
119 14.50 128 11.32 1088 1 4 .
93 18.54 163 9.62 1175 1 8 .
86 19.98 176 9.15 1204 2 0 .
68 25.23 222 7.72 1297 2 5 .
60 28.60 252 7.03 1348 2 8 .
53 32.68 287 6.40 1348 3 2 .
47 36.35 318 5.92 1348 3 6 .
43 40.08 350 5.50 1348 4 0 .
39 44.11 388 5.10 1348 4 5 .
33 51.68 454 4.38 1348 5 0 .
28 62.00 545 3.65 1348 6 3 .
24 72.27 635 3.14 1348 7 1 .
21 80.30 703 2.83 1348 8 0 .
18 96.70 848 1.94 1348 1 0 0
16 110.83 967 1.45 1348 1 1 2
14 125.96 1104 1.26 1348 1 2 5

13 127.79 1068 1.86 1348 K 0 3 5 2 1 2 5 _ N _ _ _ _ . 2 5 B - - 75.3 56C
12 145.34 1216 1.64 1348 1 4 0
10 164.66 1378 1.44 1348 1 6 0
8.2 210.58 1765 1.13 1348 2 0 0
7.6 226.95 1903 1.04 1348 2 5 0
6 286.52 2406 0.83 1348 2 8 0

16 105.69 923 3.95 1348 K 0 4 3 2 1 1 2 _ N _ _ _ _ . 2 5 B - - 68.7 56C
14 120.15 1048 3.72 1348 1 2 5

13 134.38 1132 3.45 1348 K 0 4 5 2 1 2 5 _ N _ _ _ _ . 2 5 B - - 86.3 56C
12 147.98 1243 3.14 1348 1 4 0
10 170.21 1422 2.75 1348 1 6 0
8.6 199.90 1681 2.32 1348 2 0 0
6.7 257.59 2168 1.80 1348 2 5 0
6.1 284.33 2370 1.65 1348 2 8 0
5.4 322.40 2721 1.44 1348 3 2 0
4.9 355.03 2991 1.31 1348 3 6 0
4.2 407.03 3438 1.14 1348 4 0 0
3.8 448.23 3780 1.03 1348 4 5 0
3.4 508.14 4288 0.91 1348 5 0 0

8.3 207.81 1755 3.32 1695 K 0 5 5 2 2 0 0 _ N _ _ _ _ . 2 5 B - - 117.2 56C
6.5 263.94 2231 2.61 1695 2 5 0
5.8 299.85 2536 2.30 1695 2 8 0
5.5 316.40 2690 2.17 1695 3 2 0
4.9 350.92 2984 1.95 1695 3 6 0
4.3 398.66 3392 1.72 1695 4 0 0
3.8 452.95 3849 1.51 1695 4 5 0
3.5 498.80 4245 1.37 1695 5 0 0
3 573.74 4882 1.19 1695 5 6 0
2.8 623.76 5307 1.10 1695 6 3 0
2.4 725.48 6152 0.95 1695 7 0 0
2.1 811.69 6856 0.85 1695 8 0 0

6.7 259.02 2204 3.32 1798 K 0 6 5 2 2 5 0 _ N _ _ _ _ . 2 5 B - - 134.8 56C

5.9 294.26 2505 2.92 1798 2 8 0
5.6 310.50 2655 2.75 1798 3 2 0
5 344.37 2945 2.48 1798 3 6 0
4.4 391.23 3346 2.19 1798 4 0 0
3.9 444.50 3797 1.93 1798 4 5 0
3.5 489.49 4187 1.75 1798 5 0 0
3.1 563.04 4814 1.52 1798 5 6 0
2.8 612.13 5233 1.40 1798 6 3 0
2.4 711.95 6069 1.21 1798 7 0 0
2.2 796.55 6767 1.08 1798 8 0 0
2 881.82 7521 0.97 1798 9 0 0
1.7 1025.62 8728 0.84 1798 1 0 C

NOTE 3.7 465.77 4010 3.70 3372 K 0 7 5 2 4 5 0 _ N _ _ _ _ . 2 5 B - - 174.5 56C
3.4 512.91 4420 3.36 3372 5 0 0
Other output 2.9 589.97 5080 2.92 3372 5 6 0
2.7 641.41 5520 2.69 3372 6 3 0
speeds are
2.3 737.04 6333 2.35 3372 7 0 0
available 2.1 835.78 7163 2.07 3372 8 0 0
using 6 and 8 1.9 924.00 7926 1.87 3372 9 0 0
pole motors 1.6 1061.77 9095 1.63 3372 1 0 C
- Consult 1.4 1204.01 10289 1.44 3372 1 1 C
Application 1.4 1267.37 10826 1.37 3372 1 2 C
Engineering

31
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.25 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
2.3 759.86 6504 3.69 3523 K 0 8 5 2 7 0 0 _ N _ _ _ _ . 2 5 B - - 324.4 56C
4 POLE 2.1 811.29 6944 3.46 3523 8 0 0
1.9 887.84 7594 3.16 3523 9 0 0
1.7 1006.74 8610 2.79 3523 1 0 C
1.6 1101.73 9417 2.55 3523 1 1 C
1.4 1246.44 10631 2.26 3523 1 2 C

1.7 1027.68 8799 3.80 7643 K 0 9 5 1 1 0 C _ N _ _ _ _ . 2 5 B - - 452.3 56C
1.5 1114.56 9550 3.90 7643 1 1 C
1.4 1190.00 10194 3.66 7643 1 2 C
1.2 1476.68 12638 2.95 7643 1 4 C
1.1 1640.59 14016 2.66 7643 1 6 C
0.99 1741.31 14886 2.50 7643 1 8 C
0.89 1934.60 16512 2.26 7643 2 0 C
0.81 2118.35 18067 2.06 7643 2 2 C
0.66 2596.10 22096 1.69 7643 2 5 C
0.63 2732.70 23173 1.61 7643 2 8 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

32
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.33 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 96 12.10 904 K 0 3 3 2 8 . 0 _ N _ _ _ _ . 3 3 B - - 57.5 56C
4 POLE 153 11.25 130 10.09 994 1 1 .
135 12.80 149 9.25 1036 1 2 .
119 14.50 169 8.57 1077 1 4 .
93 18.54 216 7.29 1162 1 8 .
86 19.98 232 6.93 1190 2 0 .
68 25.23 293 5.85 1278 2 5 .
60 28.60 333 5.33 1328 2 8 .
53 32.68 379 4.85 1328 3 2 .
47 36.35 420 4.49 1328 3 6 .
43 40.08 463 4.17 1328 4 0 .
39 44.11 513 3.86 1328 4 5 .
33 51.68 600 3.32 1338 5 0 .
28 62.00 719 2.77 1340 6 3 .
24 72.27 838 2.38 1348 7 1 .
21 80.30 929 2.14 1348 8 0 .
18 96.70 1119 1.47 1348 1 0 0
16 110.83 1277 1.10 1348 1 1 2
14 125.96 1457 0.95 1348 1 2 5

13 127.79 1411 1.41 1348 K 0 3 5 2 1 2 5 _ N _ _ _ _ . 3 3 B - - 77.3 56C
12 145.34 1605 1.24 1348 1 4 0
10 164.66 1819 1.09 1348 1 6 0
8.2 210.58 2330 0.85 1348 2 0 0

19 93.12 1076 3.32 1348 K 0 4 3 2 1 0 0 _ N _ _ _ _ . 3 3 B - - 70.7 56C
16 105.69 1218 2.99 1348 1 1 2
14 120.15 1384 2.82 1348 1 2 5

13 134.38 1494 2.61 1348 K 0 4 5 2 1 2 5 _ N _ _ _ _ . 3 3 B - - 88.3 56C
12 147.98 1642 2.38 1348 1 4 0
10 170.21 1877 2.08 1348 1 6 0
8.6 199.90 2219 1.76 1348 2 0 0
6.7 257.59 2862 1.37 1348 2 5 0
6.1 284.33 3128 1.25 1348 2 8 0
5.4 322.40 3592 1.09 1348 3 2 0
4.9 355.03 3949 0.99 1348 3 6 0
4.2 407.03 4539 0.86 1348 4 0 0

14 122.20 1409 3.82 1785 K 0 5 3 2 1 2 5 _ N _ _ _ _ . 3 3 B - - 88.3 56C

12 142.79 1599 3.64 1695 K 0 5 5 2 1 4 0 _ N _ _ _ _ . 3 3 B - - 119.2 56C
11 157.35 1762 3.31 1695 1 6 0
8.3 207.81 2316 2.52 1695 2 0 0
6.5 263.94 2945 1.98 1695 2 5 0
5.8 299.85 3347 1.74 1695 2 8 0
5.5 316.40 3551 1.64 1695 3 2 0
4.9 350.92 3940 1.48 1695 3 6 0
4.3 398.66 4477 1.30 1695 4 0 0
3.8 452.95 5081 1.15 1695 4 5 0
3.5 498.80 5604 1.04 1695 5 0 0
3.0 573.74 6445 0.90 1695 5 6 0
2.8 623.76 7006 0.83 1695 6 3 0

14 119.92 1381 3.82 1798 K 0 6 3 2 1 2 5 _ N _ _ _ _ . 3 3 B - - 106 56C

8.5 203.93 2290 3.19 1798 K 0 6 5 2 2 0 0 _ N _ _ _ _ . 3 3 B - - 136.8 56C
6.7 259.02 2910 2.51 1798 2 5 0
5.9 294.26 3307 2.21 1798 2 8 0
5.6 310.50 3505 2.09 1798 3 2 0
5.0 344.37 3887 1.88 1798 3 6 0
4.4 391.23 4417 1.66 1798 4 0 0
3.9 444.50 5012 1.46 1798 4 5 0
3.5 489.49 5526 1.32 1798 5 0 0
3.1 563.04 6355 1.15 1798 5 6 0
2.8 612.13 6907 1.06 1798 6 3 0
2.4 711.95 8011 0.91 1798 7 0 0
2.2 796.55 8932 0.82 1798 8 0 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

33
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.33 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
4.6 373.86 4250 3.50 3372 K 0 7 5 2 3 6 0 _ N _ _ _ _ . 3 3 B - - 176.5 56C
4 POLE 4.2 414.65 4712 3.15 3372 4 0 0
3.7 465.77 5293 2.81 3372 4 5 0
3.4 512.91 5835 2.55 3372 5 0 0
2.9 589.97 6706 2.22 3372 5 6 0
2.7 641.41 7287 2.04 3372 6 3 0
2.3 737.04 8360 1.78 3372 7 0 0
2.1 835.78 9455 1.57 3372 8 0 0
1.9 924.00 10462 1.42 3372 9 0 0
1.6 1061.77 12006 1.24 3372 1 0 C
1.4 1204.01 13582 1.09 3372 1 1 C
1.4 1267.37 14290 1.04 3372 1 2 C

3.2 537.67 6077 3.95 3523 K 0 8 5 2 5 6 0 _ N _ _ _ _ . 3 3 B - - 326.4 56C
2.7 641.16 7247 3.31 3523 6 3 0
2.3 759.86 8586 2.79 3523 7 0 0
2.1 811.29 9166 2.62 3523 8 0 0
1.9 887.84 10024 2.39 3523 9 0 0
1.7 1006.74 11365 2.11 3523 1 0 C
1.6 1101.73 12431 1.93 3523 1 1 C
1.4 1246.44 14034 1.71 3523 1 2 C

1.8 940.44 10642 3.50 7643 K 0 9 5 1 9 0 0 _ N _ _ _ _ . 3 3 B - - 454.3 56C
1.7 1027.68 11615 2.88 7643 1 0 C
1.5 1114.56 12606 2.96 7643 1 1 C
1.4 1190.00 13457 2.77 7643 1 2 C
1.2 1476.68 16682 2.24 7643 1 4 C
1.1 1640.59 18502 2.02 7643 1 6 C
0.99 1741.31 19650 1.90 7643 1 8 C
0.89 1934.60 21796 1.71 7643 2 0 C
0.81 2118.35 23849 1.56 7643 2 2 C
0.66 2596.10 29167 1.28 7643 2 5 C
0.63 2732.70 30589 1.22 7643 2 8 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

34
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.50 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 146 7.98 897 K 0 3 3 2 8 . 0 _ N _ _ _ _ . 5 0 B - - 59.5 56C
4 POLE 153 11.25 197 6.66 977 1 1 .
135 12.80 226 6.11 1016 1 2 .
119 14.50 256 5.66 1055 1 4 .
93 18.54 327 4.81 1133 1 8 .
86 19.98 352 4.57 1159 2 0 .
68 25.23 444 3.86 1240 2 5 .
60 28.60 505 3.52 1284 2 8 .
53 32.68 575 3.20 1285 3 2 .
47 36.35 636 2.96 1286 3 6 .
43 40.08 701 2.75 1286 4 0 .
39 44.11 777 2.55 1286 4 5 .
33 51.68 909 2.19 1315 5 0 .
28 62.00 1090 1.83 1321 6 3 .
24 72.27 1270 1.57 1348 7 1 .
21 80.30 1407 1.41 1348 8 0 .
18 96.70 1696 0.97 1348 1 0 0

13 127.79 2137 0.93 1348 K 0 3 5 2 1 2 5 _ N _ _ _ _ . 5 0 B - - 79.3 56C
12 145.34 2432 0.82 1348 1 4 0

29 59.24 1039 3.75 1348 K 0 4 3 2 6 3 . _ N _ _ _ _ . 5 0 B - - 72.7 56C
24 71.09 1243 3.07 1348 7 1 .
22 80.10 1393 2.75 1348 8 0 .
19 93.12 1631 2.19 1348 1 0 0
16 105.69 1846 1.97 1348 1 1 2
14 120.15 2097 1.86 1348 1 2 5

13 134.38 2264 1.73 1348 K 0 4 5 2 1 2 5 _ N _ _ _ _ . 5 0 B - - 90.3 56C
12 147.98 2487 1.57 1348 1 4 0
10 170.21 2845 1.37 1348 1 6 0
8.6 199.90 3363 1.16 1348 2 0 0
6.7 257.59 4336 0.90 1348 2 5 0
6.1 284.33 4740 0.82 1348 2 8 0

18 97.76 1710 3.41 1744 K 0 5 3 2 1 0 0 _ N _ _ _ _ . 5 0 B - - 90.3 56C
16 108.96 1901 3.07 1785 1 1 2
14 122.20 2135 2.52 1758 1 2 5

15 118.40 1997 2.92 1695 K 0 5 5 2 1 2 5 _ N _ _ _ _ . 5 0 B - - 121.2 56C
12 142.79 2423 2.41 1695 1 4 0
11 157.35 2670 2.18 1695 1 6 0
8.3 207.81 3510 1.66 1695 2 0 0
6.5 263.94 4462 1.31 1695 2 5 0
5.8 299.85 5072 1.15 1695 2 8 0
5.5 316.40 5381 1.08 1695 3 2 0
4.9 350.92 5969 0.98 1695 3 6 0
4.3 398.66 6784 0.86 1695 4 0 0

16 106.93 1870 3.91 1798 K 0 6 3 2 1 1 2 _ N _ _ _ _ . 5 0 B - - 108 56C
14 119.92 2093 2.52 1798 1 2 5

15 116.19 1974 3.70 1798 K 0 6 5 2 1 2 5 _ N _ _ _ _ . 5 0 B - - 138.8 56C
12 140.12 2393 3.06 1798 1 4 0
11 154.41 2637 2.77 1798 1 6 0
8.5 203.93 3470 2.11 1798 2 0 0
6.7 259.02 4409 1.66 1798 2 5 0
5.9 294.26 5011 1.46 1798 2 8 0
5.6 310.50 5311 1.38 1798 3 2 0
5 344.37 5890 1.24 1798 3 6 0
4.4 391.23 6692 1.09 1798 4 0 0
3.9 444.50 7594 0.96 1798 4 5 0
3.5 489.49 8374 0.87 1798 5 0 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

35
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.50 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
7.4 233.36 4028 3.69 3372 K 0 7 5 2 2 5 0 _ N _ _ _ _ . 5 0 B - - 178.5 56C
4 POLE 6.5 265.10 4576 3.25 3372 2 8 0
5.7 304.63 5247 2.83 3372 3 2 0
4.6 373.86 6439 2.31 3372 3 6 0
4.2 414.65 7140 2.08 3372 4 0 0
3.7 465.77 8020 1.85 3372 4 5 0
3.4 512.91 8841 1.68 3372 5 0 0
2.9 589.97 10161 1.46 3372 5 6 0
2.7 641.41 11041 1.35 3372 6 3 0
2.3 737.04 12667 1.17 3372 7 0 0
2.1 835.78 14327 1.04 3372 8 0 0
1.9 924.00 15852 0.94 3372 9 0 0
1.6 1061.77 18191 0.82 3372 1 0 C

3.7 462.28 7916 3.03 3523 K 0 8 5 2 4 5 0 _ N _ _ _ _ . 5 0 B - - 328.4 56C
3.4 505.90 8654 2.77 3523 5 0 0
3.2 537.67 9208 2.61 3523 5 6 0
2.7 641.16 10980 2.19 3523 6 3 0
2.3 759.86 13009 1.84 3523 7 0 0
2.1 811.29 13888 1.73 3523 8 0 0
1.9 887.84 15188 1.58 3523 9 0 0
1.7 1006.74 17220 1.39 3523 1 0 C
1.6 1101.73 18835 1.27 3523 1 1 C
1.4 1246.44 21263 1.13 3523 1 2 C

3.1 562.75 9662 3.46 7643 K 0 9 5 1 5 6 0 _ N _ _ _ _ . 5 0 B - - 456.3 56C
2.6 654.52 11237 2.97 7643 6 3 0
2.4 727.17 12458 2.68 7643 7 0 0
2.2 788.65 13523 2.76 7643 8 0 0
1.8 940.44 16124 2.31 7643 9 0 0
1.7 1027.68 17599 1.90 7643 1 0 C
1.5 1114.56 19101 1.95 7643 1 1 C
1.4 1190.00 20389 1.83 7643 1 2 C
1.2 1476.68 25276 1.48 7643 1 4 C
1.1 1640.59 28033 1.33 7643 1 6 C
0.99 1741.31 29772 1.25 7643 1 8 C
0.89 1934.60 33024 1.13 7643 2 0 C
0.81 2118.35 36135 1.03 7643 2 2 C
0.66 2596.10 44193 0.84 7643 2 5 C
0.63 2732.70 46347 0.80 7643 2 8 C

1.5 1170.88 20064 3.29 11159 K 1 0 5 1 1 1 C _ N _ _ _ _ . 5 0 B - - 731.9 56C
1.4 1268.32 21753 3.43 11159 1 2 C
1.2 1470.48 25204 2.96 11159 1 4 C
1.1 1634.03 27959 2.67 11159 1 6 C
0.98 1753.89 30032 2.48 11159 1 8 C
0.88 1948.97 33319 2.24 11159 2 0 C
0.8 2134.33 36465 2.05 11159 2 2 C
0.67 2561.20 43675 1.71 11159 2 5 C
0.62 2779.28 47260 1.58 11159 2 8 C

0.95 1811.28 31030 3.79 16198 K 1 2 5 1 1 8 C _ N _ _ _ _ . 5 0 B - - 1084.6 56C
0.84 2041.68 34956 3.37 16198 2 0 C
0.77 2235.86 38252 3.08 16198 2 2 C
0.64 2683.03 45807 2.57 16198 2 5 C
0.59 2887.22 49061 2.40 16198 2 8 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

36
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.75 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 219 5.32 886 K 0 3 3 2 8 . 0 _ N _ _ _ _ . 7 5 B - - 62.5 56C
4 POLE 153 11.25 296 4.44 952 1 1 .
135 12.80 339 4.07 988 1 2 .
119 14.50 384 3.77 1023 1 4 .
93 18.54 491 3.21 1092 1 8 .
86 19.98 528 3.05 1114 2 0 .
68 25.23 667 2.57 1183 2 5 .
60 28.60 758 2.34 1219 2 8 .
53 32.68 863 2.13 1222 3 2 .
47 36.35 955 1.97 1223 3 6 .
43 40.08 1052 1.83 1224 4 0 .
39 44.11 1166 1.70 1223 4 5 .
33 51.68 1364 1.46 1281 5 0 .
28 62.00 1635 1.22 1294 6 3 .
24 72.27 1905 1.05 1348 7 1 .
21 80.30 2111 0.94 1348 8 0 .

48 35.83 942 3.88 1315 K 0 4 3 2 3 6 . _ N _ _ _ _ . 7 5 B - - 75.7 56C
44 39.46 1042 3.51 1312 4 0 .
38 45.39 1197 3.15 1348 4 5 .
35 49.35 1300 2.96 1348 5 0 .
29 59.24 1559 2.50 1348 6 3 .
24 71.09 1865 2.04 1348 7 1 .
22 80.10 2090 1.83 1348 8 0 .
19 93.12 2447 1.46 1348 1 0 0
16 105.69 2769 1.32 1348 1 1 2
14 120.15 3145 1.24 1348 1 2 5

13 134.38 3396 1.15 1348 K 0 4 5 2 1 2 5 _ N _ _ _ _ . 7 5 B - - 93.3 56C
12 147.98 3731 1.05 1348 1 4 0
10 170.21 4267 0.92 1348 1 6 0

28 61.78 1627 3.58 1663 K 0 5 3 2 6 3 . _ N _ _ _ _ . 7 5 B - - 93.3 56C
24 72.85 1924 3.03 1714 7 1 .
22 79.77 2094 2.78 1709 8 0 .
18 97.76 2565 2.27 1691 1 0 0
16 108.96 2852 2.04 1772 1 1 2
14 122.20 3203 1.68 1719 1 2 5

15 118.40 2995 1.95 1695 K 0 5 5 2 1 2 5 _ N _ _ _ _ . 7 5 B - - 124.2 56C
12 142.79 3634 1.60 1695 1 4 0
11 157.35 4006 1.45 1695 1 6 0
8.3 207.81 5265 1.11 1695 2 0 0
6.5 263.94 6693 0.87 1695 2 5 0

24 71.49 1879 3.90 1798 K 0 6 3 2 7 1 . _ N _ _ _ _ . 7 5 B - - 111 56C
22 78.28 2055 3.56 1798 8 0 .
18 95.93 2516 2.91 1798 1 0 0
16 106.93 2806 2.61 1798 1 1 2
14 119.92 3140 1.68 1798 1 2 5

15 116.19 2962 2.47 1798 K 0 6 5 2 1 2 5 _ N _ _ _ _ . 7 5 B - - 141.8 56C
12 140.12 3590 2.04 1798 1 4 0
11 154.41 3956 1.85 1798 1 6 0
8.5 203.93 5205 1.41 1798 2 0 0
6.7 259.02 6614 1.11 1798 2 5 0
5.9 294.26 7517 0.97 1798 2 8 0
5.6 310.50 7966 0.92 1798 3 2 0
5 344.37 8836 0.83 1798 3 6 0

14 126.11 3284 3.72 3372 K 0 7 3 2 1 2 5 _ N _ _ _ _ . 7 5 B - - 152.9 56C

12 147.09 3814 3.89 3372 K 0 7 5 2 1 6 0 _ N _ _ _ _ . 7 5 B - - 181.5 56C
8.2 211.12 5455 2.72 3372 2 0 0
7.4 233.36 6042 2.46 3372 2 5 0
6.5 265.10 6864 2.16 3372 2 8 0
5.7 304.63 7870 1.89 3372 3 2 0
4.6 373.86 9659 1.54 3372 3 6 0
4.2 414.65 10711 1.39 3372 4 0 0
NOTE 3.7 465.77 12030 1.23 3372 4 5 0
3.4 512.91 13262 1.12 3372 5 0 0
Other output 2.9 589.97 15242 0.97 3372 5 6 0
2.7 641.41 16562 0.90 3372 6 3 0
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

37
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
0.75 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
3.7 462.28 11874 2.02 3523 K 0 8 5 2 4 5 0 _ N _ _ _ _ . 7 5 B - - 331.4 56C
4 POLE 3.4 505.90 12981 1.85 3523 5 0 0
3.2 537.67 13812 1.74 3523 5 6 0
2.7 641.16 16470 1.46 3523 6 3 0
2.3 759.86 19514 1.23 3523 7 0 0
2.1 811.29 20832 1.15 3523 8 0 0
1.9 887.84 22782 1.05 3523 9 0 0
1.7 1006.74 25830 0.93 3523 1 0 C
1.6 1101.73 28253 0.85 3523 1 1 C

3.1 562.75 14494 2.31 7643 K 0 9 5 1 5 6 0 _ N _ _ _ _ . 7 5 B - - 459.3 56C
2.6 654.52 16856 1.98 7643 6 3 0
2.4 727.17 18687 1.79 7643 7 0 0
2.2 788.65 20284 1.84 7643 8 0 0
1.8 940.44 24186 1.54 7643 9 0 0
1.7 1027.68 26399 1.27 7643 1 0 C
1.5 1114.56 28651 1.30 7643 1 1 C
1.4 1190.00 30584 1.22 7643 1 2 C
1.2 1476.68 37915 0.98 7643 1 4 C
1.1 1640.59 42050 0.89 7643 1 6 C
0.99 1741.31 44659 0.83 7643 1 8 C

2.7 650.62 16769 3.94 11159 K 1 0 5 1 6 3 0 _ N _ _ _ _ . 7 5 B - - 734.9 56C
2.4 722.98 18596 3.55 11159 7 0 0
2.2 783.15 20165 3.70 11159 8 0 0
1.9 904.27 23256 2.84 11159 9 0 0
1.8 979.53 25217 2.96 11159 1 0 C
1.5 1170.88 30096 2.19 11159 1 1 C
1.4 1268.32 32630 2.29 11159 1 2 C
1.2 1470.48 37806 1.97 11159 1 4 C
1.1 1634.03 41939 1.78 11159 1 6 C
0.98 1753.89 45048 1.66 11159 1 8 C
0.88 1948.97 49979 1.49 11159 2 0 C
0.8 2134.33 54697 1.36 11159 2 2 C
0.67 2561.20 65513 1.14 11159 2 5 C
0.62 2779.28 70891 1.05 11159 2 8 C

1.4 1225.51 31560 3.39 16198 K 1 2 5 1 1 2 C _ N _ _ _ _ . 7 5 B - - 1087.6 56C
1.1 1518.59 39071 3.01 16198 1 4 C
1 1711.76 44009 2.67 16198 1 6 C
0.95 1811.28 46545 2.53 16198 1 8 C
0.84 2041.68 52434 2.24 16198 2 0 C
0.77 2235.86 57378 2.05 16198 2 2 C
0.64 2683.03 68710 1.71 16198 2 5 C
0.59 2887.22 73592 1.60 16198 2 8 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

38
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
1.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 292 3.99 876 K 0 3 3 2 8 . 0 _ N _ _ _ _ 1 . 0 B - - 67.5 143TC
4 POLE 153 11.25 395 3.33 927 1 1 .
135 12.80 452 3.05 960 1 2 .
119 14.50 513 2.83 991 1 4 .
93 18.54 654 2.41 1050 1 8 .
86 19.98 704 2.29 1068 2 0 .
68 25.23 889 1.93 1126 2 5 .
60 28.60 1011 1.76 1154 2 8 .
53 32.68 1150 1.60 1158 3 2 .
47 36.35 1273 1.48 1161 3 6 .
43 40.08 1403 1.37 1162 4 0 .
39 44.11 1555 1.27 1161 4 5 .
33 51.68 1819 1.09 1247 5 0 .
28 62.00 2180 0.91 1267 6 3 .

69 25.03 880 3.69 1316 K 0 4 3 2 2 5 . _ N _ _ _ _ 1 . 0 B - - 80.7 143TC
62 27.76 978 3.41 1318 2 8 .
55 31.54 1111 3.11 1318 3 2 .
48 35.83 1256 2.91 1298 3 6 .
44 39.46 1389 2.63 1293 4 0 .
38 45.39 1597 2.37 1348 4 5 .
35 49.35 1733 2.22 1348 5 0 .
29 59.24 2079 1.88 1348 6 3 .
24 71.09 2487 1.53 1348 7 1 .
22 80.10 2787 1.37 1348 8 0 .
19 93.12 3263 1.10 1348 1 0 0
16 105.69 3692 0.99 1348 1 1 2
14 120.15 4194 0.93 1348 1 2 5

13 134.38 4528 0.86 1348 K 0 4 5 2 1 2 5 _ N _ _ _ _ 1 . 0 B - - 98.3 143TC

44 39.34 1386 3.90 1527 K 0 5 3 2 4 0 . _ N _ _ _ _ 1 . 0 B - - 98.3 143TC
37 46.63 1644 3.42 1547 4 5 .
35 49.78 1748 3.27 1536 5 0 .
28 61.78 2170 2.68 1596 6 3 .
24 72.85 2565 2.27 1672 7 1 .
22 79.77 2792 2.09 1665 8 0 .
18 97.76 3420 1.71 1638 1 0 0
16 108.96 3803 1.53 1759 1 1 2
14 122.20 4271 1.26 1679 1 2 5

15 118.40 3994 1.46 1695 K 0 5 5 2 1 2 5 _ N _ _ _ _ 1 . 0 B - - 129.2 143TC
12 142.79 4846 1.20 1695 1 4 0
11 157.35 5341 1.09 1695 1 6 0
8.3 207.81 7021 0.83 1695 2 0 0

28 60.62 2129 3.44 1788 K 0 6 3 2 6 3 . _ N _ _ _ _ 1 . 0 B - - 116 143TC
24 71.49 2505 2.92 1798 7 1 .
22 78.28 2741 2.67 1798 8 0 .
18 95.93 3355 2.18 1798 1 0 0
16 106.93 3741 1.96 1798 1 1 2
14 119.92 4187 1.26 1798 1 2 5

15 116.19 3949 1.85 1798 K 0 6 5 2 1 2 5 _ N _ _ _ _ 1 . 0 B - - 146.8 143TC
12 140.12 4786 1.53 1798 1 4 0
11 154.41 5275 1.39 1798 1 6 0
8.5 203.93 6940 1.05 1798 2 0 0
6.7 259.02 8819 0.83 1798 2 5 0

15 113.50 3968 3.64 3300 K 0 7 3 2 1 1 2 _ N _ _ _ _ 1 . 0 B - - 157.9 143TC
14 126.11 4379 2.79 3372 1 2 5

14 120.29 4142 3.59 3372 K 0 7 5 2 1 2 5 _ N _ _ _ _ 1 . 0 B - - 186.5 143TC
13 133.48 4615 3.22 3372 1 4 0
12 147.09 5086 2.92 3372 1 6 0
8.2 211.12 7273 2.04 3372 2 0 0
7.4 233.36 8056 1.84 3372 2 5 0
6.5 265.10 9152 1.62 3372 2 8 0
5.7 304.63 10494 1.42 3372 3 2 0
NOTE 4.6 373.86 12879 1.15 3372 3 6 0
4.2 414.65 14281 1.04 3372 4 0 0
Other output 3.7 465.77 16040 0.93 3372 4 5 0
3.4 512.91 17682 0.84 3372 5 0 0
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

39
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
1.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
3.7 462.28 15833 1.52 3523 K 0 8 5 2 4 5 0 _ N _ _ _ _ 1 . 0 B - - 336.4 143TC
4 POLE 3.4 505.90 17309 1.39 3523 5 0 0
3.2 537.67 18416 1.30 3523 5 6 0
2.7 641.16 21961 1.09 3523 6 3 0
2.3 759.86 26019 0.92 3523 7 0 0
2.1 811.29 27776 0.86 3523 8 0 0

3.1 562.75 19325 1.73 7643 K 0 9 5 1 5 6 0 _ N _ _ _ _ 1 . 0 B - - 464.3 143TC
2.6 654.52 22475 1.49 7643 6 3 0
2.4 727.17 24916 1.34 7643 7 0 0
2.2 788.65 27046 1.38 7643 8 0 0
1.8 940.44 32248 1.16 7643 9 0 0
1.7 1027.68 35199 0.95 7643 1 0 C
1.5 1114.56 38202 0.98 7643 1 1 C
1.4 1190.00 40779 0.91 7643 1 2 C

3.4 514.73 17691 3.73 11159 K 1 0 5 1 5 0 0 _ N _ _ _ _ 1 . 0 B - - 739.9 143TC
3 566.20 19460 3.39 11159 5 6 0
2.7 650.62 22359 2.95 11159 6 3 0
2.4 722.98 24794 2.66 11159 7 0 0
2.2 783.15 26887 2.77 11159 8 0 0
1.9 904.27 31008 2.13 11159 9 0 0
1.8 979.53 33622 2.22 11159 1 0 C
1.5 1170.88 40128 1.65 11159 1 1 C
1.4 1268.32 43506 1.71 11159 1 2 C
1.2 1470.48 50408 1.48 11159 1 4 C
1.1 1634.03 55918 1.33 11159 1 6 C
0.98 1753.89 60064 1.24 11159 1 8 C
0.88 1948.97 66639 1.12 11159 2 0 C
0.8 2134.33 72930 1.02 11159 2 2 C
0.67 2561.20 87351 0.85 11159 2 5 C

1.8 946.46 32530 3.29 16198 K 1 2 5 1 9 0 0 _ N _ _ _ _ 1 . 0 B - - 1092.6 143TC
1.7 1011.58 34767 3.38 16198 1 0 C
1.5 1140.25 39153 3.01 16198 1 1 C
1.4 1225.51 42080 2.54 16198 1 2 C
1.1 1518.59 52095 2.26 16198 1 4 C
1 1711.76 58679 2.01 16198 1 6 C
0.95 1811.28 62061 1.90 16198 1 8 C
0.84 2041.68 69912 1.68 16198 2 0 C
0.77 2235.86 76504 1.54 16198 2 2 C
0.64 2683.03 91614 1.28 16198 2 5 C
0.59 2887.22 98123 1.20 16198 2 8 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

40
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
1.50 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 438 2.66 854 K 0 3 3 2 8 . 0 _ N _ _ _ _ 1 . 5 B - - 71.5 145TC
4 POLE 153 11.25 593 2.22 878 1 1 .
135 12.80 678 2.04 903 1 2 .
119 14.50 769 1.89 926 1 4 .
93 18.54 982 1.60 966 1 8 .
86 19.98 1056 1.52 978 2 0 .
68 25.23 1334 1.29 1012 2 5 .
60 28.60 1517 1.17 1025 2 8 .
53 32.68 1726 1.07 1032 3 2 .
47 36.35 1910 0.99 1036 3 6 .
43 40.08 2105 0.92 1039 4 0 .
39 44.11 2333 0.85 1036 4 5 .

139 12.45 656 3.95 1224 K 0 4 3 2 1 2 . _ N _ _ _ _ 1 . 5 B - - 84.7 145TC
122 14.14 748 3.63 1260 1 4 .
96 17.95 947 3.10 1308 1 8 .
85 20.40 1079 2.84 1312 2 0 .
69 25.03 1321 2.46 1295 2 5 .
62 27.76 1467 2.27 1297 2 8 .
55 31.54 1666 2.07 1297 3 2 .
48 35.83 1885 1.94 1265 3 6 .
44 39.46 2084 1.75 1257 4 0 .
38 45.39 2395 1.58 1348 4 5 .
35 49.35 2600 1.48 1348 5 0 .
29 59.24 3119 1.25 1348 6 3 .
24 71.09 3731 1.02 1348 7 1 .
22 80.10 4181 0.92 1348 8 0 .

61 28.37 1498 3.33 1331 K 0 5 3 2 2 8 . _ N _ _ _ _ 1 . 5 B - - 102.3 145TC
52 32.99 1746 2.97 1343 3 2 .
47 36.91 1948 2.79 1449 3 6 .
44 39.34 2080 2.60 1456 4 0 .
37 46.63 2466 2.28 1379 4 5 .
35 49.78 2622 2.18 1362 5 0 .
28 61.78 3255 1.79 1461 6 3 .
24 72.85 3848 1.52 1587 7 1 .
22 79.77 4189 1.39 1576 8 0 .
18 97.76 5130 1.14 1531 1 0 0
16 108.96 5705 1.02 1733 1 1 2
14 122.20 6407 0.84 1600 1 2 5

15 118.40 5991 0.97 1695 K 0 5 5 2 1 2 5 _ N _ _ _ _ 1 . 5 B - - 133.2 145TC
12 142.79 7269 0.80 1695 1 4 0

48 36.22 1911 3.82 1610 K 0 6 3 2 3 6 . _ N _ _ _ _ 1 . 5 B - - 120 145TC
45 38.61 2038 3.59 1597 4 0 .
38 45.76 2414 3.03 1556 4 5 .
35 48.86 2579 2.84 1798 5 0 .
28 60.62 3194 2.29 1781 6 3 .
24 71.49 3758 1.95 1798 7 1 .
22 78.28 4111 1.78 1798 8 0 .
18 95.93 5033 1.45 1798 1 0 0
16 106.93 5612 1.30 1798 1 1 2
14 119.92 6281 0.84 1798 1 2 5

15 116.19 5924 1.23 1798 K 0 6 5 2 1 2 5 _ N _ _ _ _ 1 . 5 B - - 150.8 145TC
12 140.12 7180 1.02 1798 1 4 0
11 154.41 7913 0.92 1798 1 6 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

41
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
1.50 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
23 75.07 3951 3.76 3182 K 0 7 3 2 7 1 . _ N _ _ _ _ 1 . 5 B - - 161.9 145TC
4 POLE 21 82.21 4315 3.45 3172 8 0 .
17 98.65 5175 2.87 3142 1 0 0
15 113.50 5953 2.42 3228 1 1 2
14 126.11 6568 1.86 3372 1 2 5

14 120.29 6213 2.39 3372 K 0 7 5 2 1 2 5 _ N _ _ _ _ 1 . 5 B - - 192.7 145TC
13 133.48 6923 2.15 3372 1 4 0
12 147.09 7629 1.95 3372 1 6 0
8.2 211.12 10910 1.36 3372 2 0 0
7.4 233.36 12084 1.23 3372 2 5 0
6.5 265.10 13728 1.08 3372 2 8 0
5.7 304.63 15741 0.94 3372 3 2 0

14 123.33 6439 3.68 4662 K 0 8 3 2 1 2 5 _ N _ _ _ _ 1 . 5 B - - 289.7 145TC

3.7 462.28 23749 1.01 3523 K 0 8 5 2 4 5 0 _ N _ _ _ _ 1 . 5 B - - 340.4 145TC
3.4 505.90 25963 0.92 3523 5 0 0
3.2 537.67 27624 0.87 3523 5 6 0

3.1 562.75 28988 1.15 7643 K 0 9 5 1 5 6 0 _ N _ _ _ _ 1 . 5 B - - 468.3 145TC
2.6 654.52 33713 0.99 7643 6 3 0
2.4 727.17 37375 0.89 7643 7 0 0
2.2 788.65 40569 0.92 7643 8 0 0

3.4 514.73 26537 2.49 11159 K 1 0 5 1 5 0 0 _ N _ _ _ _ 1 . 5 B - - 743.9 145TC
3 566.20 29190 2.26 11159 5 6 0
2.7 650.62 33539 1.97 11159 6 3 0
2.4 722.98 37192 1.78 11159 7 0 0
2.2 783.15 40331 1.85 11159 8 0 0
1.9 904.27 46512 1.42 11159 9 0 0
1.8 979.53 50434 1.48 11159 1 0 C
1.5 1170.88 60192 1.10 11159 1 1 C
1.4 1268.32 65260 1.14 11159 1 2 C
1.2 1470.48 75612 0.99 11159 1 4 C
1.1 1634.03 83878 0.89 11159 1 6 C
0.98 1753.89 90096 0.83 11159 1 8 C

3.2 531.11 27433 3.90 16198 K 1 2 5 1 5 0 0 _ N _ _ _ _ 1 . 5 B - - 1096.6 145TC
3 584.22 30173 3.55 16198 5 6 0
2.6 671.32 34660 3.09 16198 6 3 0
2.3 756.72 39032 2.74 16198 7 0 0
2.1 808.78 41719 2.82 16198 8 0 0
1.8 946.46 48795 2.19 16198 9 0 0
1.7 1011.58 52151 2.26 16198 1 0 C
1.5 1140.25 58730 2.00 16198 1 1 C
1.4 1225.51 63120 1.70 16198 1 2 C
1.1 1518.59 78142 1.51 16198 1 4 C
1 1711.76 88019 1.34 16198 1 6 C
0.95 1811.28 93091 1.26 16198 1 8 C
0.84 2041.68 104869 1.12 16198 2 0 C
0.77 2235.86 114756 1.03 16198 2 2 C
0.64 2683.03 137421 0.86 16198 2 5 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

42
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
2.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 585 2.00 833 K 0 3 3 2 8 . 0 _ N _ _ _ _ 2 . 0 B - - 78.5 145TC
4 POLE 153 11.25 791 1.67 828 1 1 .
135 12.80 904 1.53 846 1 2 .
119 14.50 1026 1.41 862 1 4 .
93 18.54 1309 1.20 883 1 8 .
86 19.98 1408 1.14 887 2 0 .
68 25.23 1779 0.96 898 2 5 .
60 28.60 2023 0.88 896 2 8 .

214 8.05 566 3.86 1076 K 0 4 3 2 8 . 0 _ N _ _ _ _ 2 . 0 B - - 91.7 145TC
153 11.30 794 3.15 1158 1 1 .
139 12.45 875 2.96 1210 1 2 .
122 14.14 997 2.72 1245 1 4 .
96 17.95 1263 2.33 1291 1 8 .
85 20.40 1438 2.13 1298 2 0 .
69 25.03 1761 1.84 1274 2 5 .
62 27.76 1956 1.71 1277 2 8 .
55 31.54 2222 1.55 1277 3 2 .
48 35.83 2513 1.45 1231 3 6 .
44 39.46 2779 1.32 1220 4 0 .
38 45.39 3194 1.18 1348 4 5 .
35 49.35 3467 1.11 1348 5 0 .
29 59.24 4158 0.94 1348 6 3 .

61 28.37 1998 2.50 1249 K 0 5 3 2 2 8 . _ N _ _ _ _ 2 . 0 B - - 109.3 145TC
52 32.99 2328 2.23 1248 3 2 .
47 36.91 2597 2.10 1382 3 6 .
44 39.34 2773 1.95 1385 4 0 .
37 46.63 3288 1.71 1212 4 5 .
35 49.78 3496 1.63 1188 5 0 .
28 61.78 4340 1.34 1326 6 3 .
24 72.85 5130 1.14 1503 7 1 .
22 79.77 5585 1.04 1487 8 0 .
18 97.76 6840 0.85 1424 1 0 0

62 27.84 1961 3.69 1588 K 0 6 3 2 2 8 . _ N _ _ _ _ 2 . 0 B - - 127 145TC
53 32.38 2280 3.21 1560 3 2 .
48 36.22 2548 2.87 1535 3 6 .
45 38.61 2717 2.69 1516 4 0 .
38 45.76 3219 2.27 1459 4 5 .
35 48.86 3439 2.13 1798 5 0 .
28 60.62 4259 1.72 1774 6 3 .
24 71.49 5011 1.46 1798 7 1 .
22 78.28 5482 1.34 1798 8 0 .
18 95.93 6711 1.09 1798 1 0 0
16 106.93 7482 0.98 1798 1 1 2

15 116.19 7899 0.93 1798 K 0 6 5 2 1 2 5 _ N _ _ _ _ 2 . 0 B - - 157.8 145TC

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

43
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
2.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
32 54.28 3813 3.90 3090 K 0 7 3 2 5 0 . _ N _ _ _ _ 2 . 0 B - - 168.9 145TC
4 POLE 27 62.94 4419 3.36 3064 6 3 .
23 75.07 5268 2.82 3087 7 1 .
21 82.21 5753 2.58 3072 8 0 .
17 98.65 6901 2.15 3027 1 0 0
15 113.50 7937 1.82 3156 1 1 2
14 126.11 8758 1.39 3372 1 2 5

14 120.29 8284 1.79 3372 K 0 7 5 2 1 2 5 _ N _ _ _ _ 2 . 0 B - - 199.7 145TC
13 133.48 9231 1.61 3372 1 4 0
12 147.09 10172 1.46 3372 1 6 0
8.2 211.12 14546 1.02 3372 2 0 0
7.4 233.36 16113 0.92 3372 2 5 0
6.5 265.10 18304 0.81 3372 2 8 0

18 98.08 6862 3.46 4508 K 0 8 3 2 1 0 0 _ N _ _ _ _ 2 . 0 B - - 296.7 145TC
16 107.10 7492 3.17 4490 1 1 2
14 123.33 8585 2.76 4490 1 2 5

3.1 562.75 38651 0.86 7643 K 0 9 5 1 5 6 0 _ N _ _ _ _ 2 . 0 B - - 475.3 145TC

3.4 514.73 35382 1.87 11159 K 1 0 5 1 5 0 0 _ N _ _ _ _ 2 . 0 B - - 750.9 145TC
3 566.20 38921 1.70 11159 5 6 0
2.7 650.62 44718 1.48 11159 6 3 0
2.4 722.98 49589 1.33 11159 7 0 0
2.2 783.15 53775 1.39 11159 8 0 0
1.9 904.27 62016 1.07 11159 9 0 0
1.8 979.53 67245 1.11 11159 1 0 C
1.5 1170.88 80256 0.82 11159 1 1 C
1.4 1268.32 87013 0.86 11159 1 2 C

3.2 531.11 36578 2.93 16198 K 1 2 5 1 5 0 0 _ N _ _ _ _ 2 . 0 B - - 1103.6 145TC
3 584.22 40231 2.66 16198 5 6 0
2.6 671.32 46214 2.32 16198 6 3 0
2.3 756.72 52042 2.06 16198 7 0 0
2.1 808.78 55626 2.12 16198 8 0 0
1.8 946.46 65060 1.65 16198 9 0 0
1.7 1011.58 69535 1.69 16198 1 0 C
1.5 1140.25 78307 1.50 16198 1 1 C
1.4 1225.51 84161 1.27 16198 1 2 C
1.1 1518.59 104190 1.13 16198 1 4 C
1 1711.76 117359 1.00 16198 1 6 C
0.95 1811.28 124122 0.95 16198 1 8 C
0.84 2041.68 139825 0.84 16198 2 0 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

44
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
3.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.33 877 1.33 791 K 0 3 3 2 8 . 0 _ N _ _ _ _ 3 . 0 B - - 98.5 182TC
4 POLE 153 11.25 1187 1.11 728 1 1 .
135 12.80 1356 1.02 733 1 2 .
119 14.50 1539 0.94 733 1 4 .

214 8.05 849 2.57 1064 K 0 4 3 2 8 . 0 _ N _ _ _ _ 3 . 0 B - - 113.9 182TC
153 11.30 1191 2.10 1141 1 1 .
139 12.45 1313 1.97 1183 1 2 .
122 14.14 1496 1.82 1214 1 4 .
96 17.95 1894 1.55 1259 1 8 .
85 20.40 2158 1.42 1269 2 0 .
69 25.03 2642 1.23 1232 2 5 .
62 27.76 2935 1.14 1236 2 8 .
55 31.54 3333 1.04 1236 3 2 .

213 8.11 854 3.90 1047 K 0 5 3 2 8 . 0 _ N _ _ _ _ 3 . 0 B - - 144.8 182TC
151 11.40 1205 3.17 1108 1 1 .
135 12.78 1350 2.94 1131 1 2 .
120 14.35 1517 2.72 1153 1 4 .
95 18.22 1924 2.31 1191 1 8 .
84 20.66 2181 2.10 1205 2 0 .
70 24.64 2607 1.85 1221 2 5 .
61 28.37 2997 1.67 1084 2 8 .
52 32.99 3492 1.48 1057 3 2 .
47 36.91 3896 1.40 1249 3 6 .
44 39.34 4160 1.30 1242 4 0 .
37 46.63 4932 1.14 878 4 5 .
35 49.78 5245 1.09 839 5 0 .
28 61.78 6510 0.89 1057 6 3 .

123 14.08 1488 3.98 1630 K 0 6 3 2 1 4 . _ N _ _ _ _ 3 . 0 B - - 162.4 182TC
96 17.88 1893 3.39 1798 1 8 .
85 20.27 2143 3.09 1798 2 0 .
71 24.18 2557 2.73 1798 2 5 .
62 27.84 2942 2.46 1467 2 8 .
53 32.38 3420 2.14 1425 3 2 .
48 36.22 3823 1.91 1384 3 6 .
45 38.61 4076 1.79 1356 4 0 .
38 45.76 4829 1.52 1266 4 5 .
35 48.86 5158 1.42 1798 5 0 .
28 60.62 6389 1.15 1760 6 3 .
24 71.49 7516 0.97 1798 7 1 .
22 78.28 8223 0.89 1798 8 0 .

51 33.52 3544 3.82 2348 K 0 7 3 2 3 2 . _ N _ _ _ _ 3 . 0 B - - 202.1 182TC
45 38.01 3997 3.54 2611 3 6 .
41 41.92 4405 3.23 2629 4 0 .
36 48.01 5051 2.93 2794 4 5 .
32 54.28 5719 2.60 2902 5 0 .
27 62.94 6629 2.24 2859 6 3 .
23 75.07 7903 1.88 2897 7 1 .
21 82.21 8630 1.72 2872 8 0 .
17 98.65 10351 1.44 2797 1 0 0
15 113.50 11906 1.21 3012 1 1 2
14 126.11 13137 0.93 3372 1 2 5

14 120.29 12427 1.20 3372 K 0 7 5 2 1 2 5 _ N _ _ _ _ 3 . 0 B - - 219.7 182TC
13 133.48 13846 1.07 3372 1 4 0
12 147.09 15258 0.97 3372 1 6 0

28 62.47 6565 3.61 3804 K 0 8 3 2 6 3 . _ N _ _ _ _ 3 . 0 B - - 325.6 182TC
24 72.86 7646 3.10 3871 7 1 .
22 80.03 8398 2.82 3894 8 0 .
18 98.08 10293 2.30 4182 1 0 0
16 107.10 11238 2.11 4148 1 1 2
14 123.33 12878 1.84 4148 1 2 5

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

45
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
3.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
13 132.19 13570 1.77 3523 K 0 8 5 2 1 2 5 _ N _ _ _ _ 3 . 0 B - - 382.9 182TC
4 POLE 12 144.67 14830 1.62 3523 1 4 0
11 163.67 16719 1.44 3523 1 6 0
8.5 203.40 20854 1.15 3523 2 0 0
6.7 255.90 26241 0.91 3523 2 5 0

18 93.71 9810 3.80 7643 K 0 9 3 1 1 0 0 _ N _ _ _ _ 3 . 0 B - - 449 182TC
16 106.99 11215 2.98 7643 1 1 2
14 120.31 12591 2.66 7643 1 2 5
13 128.92 13465 2.77 7643 1 4 0
12 144.96 15101 2.47 7643 1 6 0

11 160.93 16573 2.02 7643 K 0 9 5 1 1 6 0 _ N _ _ _ _ 3 . 0 B - - 510.7 182TC
7.6 226.25 23303 1.43 7643 2 0 0
6.8 253.59 26120 1.28 7643 2 5 0
6.1 281.74 28944 1.15 7643 2 8 0
5.5 316.25 32492 1.03 7643 3 2 0
4.8 361.50 37239 0.90 7643 3 6 0
4.3 401.62 41270 0.81 7643 4 0 0

3.4 514.73 53074 1.24 11159 K 1 0 5 1 5 0 0 _ N _ _ _ _ 3 . 0 B - - 784.1 182TC
3 566.20 58381 1.13 11159 5 6 0
2.7 650.62 67078 0.98 11159 6 3 0
2.4 722.98 74384 0.89 11159 7 0 0
2.2 783.15 80663 0.92 11159 8 0 0

3.2 531.11 54867 1.95 16198 K 1 2 5 1 5 0 0 _ N _ _ _ _ 3 . 0 B - - 1136.8 182TC
3 584.22 60346 1.77 16198 5 6 0
2.6 671.32 69321 1.54 16198 6 3 0
2.3 756.72 78064 1.37 16198 7 0 0
2.1 808.78 83439 1.41 16198 8 0 0
1.8 946.46 97590 1.10 16198 9 0 0
1.7 1011.58 104303 1.13 16198 1 0 C
1.5 1140.25 117460 1.00 16198 1 1 C
1.4 1225.51 126241 0.85 16198 1 2 C

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

46
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
5.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
214 8.05 1415 1.54 1040 K 0 4 3 2 8 . 0 _ N _ _ _ _ 5 . 0 B - - 127.9 184TC
4 POLE 153 11.30 1986 1.26 1108 1 1 .
139 12.45 2189 1.18 1128 1 2 .
122 14.14 2494 1.09 1153 1 4 .
96 17.95 3157 0.93 1193 1 8 .
85 20.40 3597 0.85 1211 2 0 .

213 8.11 1424 2.34 977 K 0 5 3 2 8 . 0 _ N _ _ _ _ 5 . 0 B - - 158.8 184TC
151 11.40 2008 1.90 1009 1 1 .
135 12.78 2250 1.77 1020 1 2 .
120 14.35 2529 1.63 1028 1 4 .
95 18.22 3207 1.39 945 1 8 .
84 20.66 3635 1.26 927 2 0 .
70 24.64 4346 1.11 814 2 5 .
61 28.37 4995 1.00 755 2 8 .
52 32.99 5821 0.89 674 3 2 .
47 36.91 6494 0.84 982 3 6 .

217 7.96 1399 3.38 1378 K 0 6 3 2 8 . 0 _ N _ _ _ _ 5 . 0 B - - 176.4 184TC
154 11.19 1967 2.78 1487 1 1 .
138 12.54 2211 2.58 1517 1 2 .
123 14.08 2481 2.39 1546 1 4 .
96 17.88 3156 2.03 1665 1 8 .
85 20.27 3571 1.86 1660 2 0 .
71 24.18 4261 1.64 1649 2 5 .
62 27.84 4904 1.48 1227 2 8 .
53 32.38 5701 1.28 1153 3 2 .
48 36.22 6371 1.15 1083 3 6 .
45 38.61 6794 1.08 1034 4 0 .
38 45.76 8048 0.91 879 4 5 .
35 48.86 8598 0.85 1798 5 0 .

65 26.52 4680 2.72 2024 K 0 7 3 2 2 5 . _ N _ _ _ _ 5 . 0 B - - 216.1 184TC
59 29.17 5115 2.54 2003 2 8 .
51 33.52 5907 2.29 1960 3 2 .
45 38.01 6662 2.13 2237 3 6 .
41 41.92 7343 1.94 2214 4 0 .
36 48.01 8419 1.76 2439 4 5 .
32 54.28 9532 1.56 2526 5 0 .
27 62.94 11049 1.35 2449 6 3 .
23 75.07 13171 1.13 2518 7 1 .
21 82.21 14384 1.03 2473 8 0 .
17 98.65 17252 0.86 2338 1 0 0

52 33.24 5812 3.81 3066 K 0 8 3 2 3 2 . _ N _ _ _ _ 5 . 0 B - - 339.6 184TC
47 36.88 6445 3.54 2880 3 6 .
43 40.36 7097 3.30 2898 4 0 .
38 45.66 8010 2.96 3097 4 5 .
33 51.54 9035 2.63 3471 5 0 .
28 62.47 10941 2.17 3404 6 3 .
24 72.86 12744 1.86 3403 7 1 .
22 80.03 13997 1.69 3383 8 0 .
18 98.08 17155 1.38 3532 1 0 0
16 107.10 18731 1.27 3463 1 1 2
14 123.33 21464 1.11 3462 1 2 5

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

47
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
5.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
13 132.19 22617 1.06 3523 K 0 8 5 2 1 2 5 _ N _ _ _ _ 5 . 0 B - - 396.9 184TC
4 POLE 12 144.67 24716 0.97 3523 1 4 0
11 163.67 27865 0.86 3523 1 6 0

35 49.87 8727 3.83 7643 K 0 9 3 1 5 0 . _ N _ _ _ _ 5 . 0 B - - 463 184TC
32 54.09 9459 3.94 7643 5 6 .
29 60.10 10518 3.54 7643 6 3 .
24 70.45 12286 2.72 7643 7 1 .
22 77.78 13636 2.45 7643 8 0 .
20 84.89 14804 2.52 7643 9 0 .
18 93.71 16350 2.28 7643 1 0 0
16 106.99 18692 1.79 7643 1 1 2
14 120.31 20986 1.59 7643 1 2 5
13 128.92 22443 1.66 7643 1 4 0
12 144.96 25168 1.48 7643 1 6 0

11 160.93 27622 1.21 7643 K 0 9 5 1 1 6 0 _ N _ _ _ _ 5 . 0 B - - 524.7 184TC
7.6 226.25 38839 0.86 7643 2 0 0

17 99.70 17461 3.67 11210 K 1 0 3 1 1 0 0 _ N _ _ _ _ 5 . 0 B - - 738.6 184TC
15 112.03 19573 3.28 11207 1 1 2
14 120.36 21105 3.04 11206 1 2 5
13 134.85 23564 2.72 11203 1 4 0
12 144.88 25230 2.54 11211 1 6 0

3.2 531.11 91446 1.17 16198 K 1 2 5 1 5 0 0 _ N _ _ _ _ 5 . 0 B - - 1150.8 184TC
3 584.22 100578 1.06 16198 5 6 0
2.6 671.32 115536 0.93 16198 6 3 0
2.3 756.72 130107 0.82 16198 7 0 0
2.1 808.78 139065 0.85 16198 8 0 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

48
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
7.50 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
213 8.11 2136 1.56 890 K 0 5 3 2 8 . 0 _ N _ _ _ _ 7 . 5 B - - 206.8 213TC
4 POLE 151 11.40 3013 1.27 885 1 1 .
135 12.78 3375 1.18 882 1 2 .
120 14.35 3794 1.09 872 1 4 .
95 18.22 4810 0.92 638 1 8 .
84 20.66 5453 0.84 579 2 0 .

217 7.96 2098 2.26 1344 K 0 6 3 2 8 . 0 _ N _ _ _ _ 7 . 5 B - - 224.4 213TC
154 11.19 2950 1.85 1404 1 1 .
138 12.54 3316 1.72 1424 1 2 .
123 14.08 3721 1.59 1442 1 4 .
96 17.88 4734 1.36 1497 1 8 .
85 20.27 5357 1.24 1487 2 0 .
71 24.18 6392 1.09 1463 2 5 .

201 8.60 2250 2.78 2059 K 0 7 3 2 8 . 0 _ N _ _ _ _ 7 . 5 B - - 264.1 213TC
145 11.91 3127 2.78 2157 1 1 .
129 13.37 3527 2.78 2216 1 2 .
117 14.71 3870 2.77 2270 1 4 .
90 19.21 5099 2.29 2382 1 8 .
79 21.84 5787 2.08 2450 2 0 .
65 26.52 7020 1.82 1638 2 5 .
59 29.17 7673 1.70 1580 2 8 .
51 33.52 8861 1.53 1475 3 2 .
45 38.01 9993 1.42 1769 3 6 .
41 41.92 11014 1.29 1696 4 0 .
36 48.01 12629 1.17 1996 4 5 .
32 54.28 14299 1.04 2056 5 0 .
27 62.94 16574 0.90 1937 6 3 .

83 20.67 5454 3.68 2377 K 0 8 3 2 2 0 . _ N _ _ _ _ 7 . 5 B - - 387.6 213TC
68 25.35 6695 3.12 2553 2 5 .
60 28.56 7517 2.84 2571 2 8 .
52 33.24 8718 2.54 2768 3 2 .
47 36.88 9668 2.36 2586 3 6 .
43 40.36 10646 2.20 2573 4 0 .
38 45.66 12016 1.97 2687 4 5 .
33 51.54 13553 1.75 3238 5 0 .
28 62.47 16412 1.45 2904 6 3 .
24 72.86 19116 1.24 2818 7 1 .
22 80.03 20995 1.13 2743 8 0 .
18 98.08 25732 0.92 2718 1 0 0
16 107.10 28096 0.84 2606 1 1 2

38 44.89 11790 2.84 7643 K 0 9 3 1 4 5 . _ N _ _ _ _ 7 . 5 B - - 511 213TC
35 49.87 13091 2.56 7643 5 0 .
32 54.09 14188 2.63 7643 5 6 .
29 60.10 15777 2.36 7643 6 3 .
24 70.45 18429 1.82 7643 7 1 .
22 77.78 20454 1.64 7643 8 0 .
20 84.89 22207 1.68 7643 9 0 .
18 93.71 24526 1.52 7643 1 0 0
16 106.99 28038 1.19 7643 1 1 2
14 120.31 31479 1.06 7643 1 2 5
13 128.92 33664 1.11 7643 1 4 0
12 144.96 37752 0.99 7643 1 6 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

49
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
7.50 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
24 71.89 18962 3.38 11202 K 1 0 3 1 7 1 . _ N _ _ _ _ 7 . 5 B - - 786.6 213TC
4 POLE 21 82.83 21800 2.94 11199 8 0 .
20 86.53 22754 2.82 11199 9 0 .
17 99.70 26192 2.45 11200 1 0 0
15 112.03 29360 2.19 11194 1 1 2
14 120.36 31658 2.03 11192 1 2 5
13 134.85 35347 1.82 11184 1 4 0
12 144.88 37845 1.70 11203 1 6 0

10 166.84 42986 1.54 11159 K 1 0 5 1 1 6 0 _ N _ _ _ _ 7 . 5 B - - 846.1 213TC
7.5 231.10 59549 1.11 11159 2 0 0
6.6 259.60 66896 0.99 11159 2 5 0
6 285.44 73561 0.90 11159 2 8 0
5.4 317.19 81542 0.81 11159 3 2 0

15 113.79 29785 3.60 16249 K 1 2 3 1 1 1 2 _ N _ _ _ _ 7 . 5 B - - 1106.3 213TC
14 121.06 31813 3.37 16246 1 2 5
13 137.09 35911 3.03 16257 1 4 0
12 145.85 38128 2.86 16258 1 6 0

10 172.15 44472 2.41 16198 K 1 2 5 1 1 6 0 _ N _ _ _ _ 7 . 5 B - - 1198.8 213TC
6.4 268.79 69352 1.54 16198 2 0 0
7.2 238.46 61605 1.74 16198 2 5 0
5.7 301.94 77906 1.37 16198 2 8 0
5.2 331.99 85665 1.25 16198 3 2 0
4.5 384.70 99376 1.08 16198 3 6 0
3.9 437.38 112977 0.95 16198 4 0 0
3.5 493.02 127203 0.84 16198 4 5 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

50
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
10.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
213 8.11 2849 1.17 802 K 0 5 3 2 8 . 0 _ N _ _ _ _ 1 0 . B - - 221.8 215TC
4 POLE 151 11.40 4017 0.95 762 1 1 .
135 12.78 4500 0.88 744 1 2 .
120 14.35 5059 0.82 717 1 4 .

217 7.96 2798 1.69 1310 K 0 6 3 2 8 . 0 _ N _ _ _ _ 1 0 . B - - 239.4 215TC
154 11.19 3934 1.39 1321 1 1 .
138 12.54 4422 1.29 1330 1 2 .
123 14.08 4962 1.19 1337 1 4 .
96 17.88 6312 1.02 1330 1 8 .
85 20.27 7143 0.93 1315 2 0 .
71 24.18 8523 0.82 1276 2 5 .

201 8.60 3000 2.09 1977 K 0 7 3 2 8 . 0 _ N _ _ _ _ 1 0 . B - - 279.1 215TC
145 11.91 4169 2.09 2044 1 1 .
129 13.37 4703 2.09 2088 1 2 .
117 14.71 5160 2.08 2128 1 4 .
90 19.21 6798 1.72 2200 1 8 .
79 21.84 7717 1.56 2240 2 0 .
65 26.52 9360 1.36 1251 2 5 .
59 29.17 10231 1.27 1157 2 8 .
51 33.52 11815 1.15 991 3 2 .
45 38.01 13324 1.06 1301 3 6 .
41 41.92 14686 0.97 1177 4 0 .
36 48.01 16839 0.88 1553 4 5 .

135 12.80 4479 3.83 2205 K 0 8 3 2 1 2 . _ N _ _ _ _ 1 0 . B - - 402.6 215TC
121 14.24 5009 3.62 2226 1 4 .
94 18.41 6462 3.04 2247 1 8 .
83 20.67 7272 2.76 2249 2 0 .
68 25.35 8927 2.34 2360 2 5 .
60 28.56 10022 2.13 2350 2 8 .
52 33.24 11624 1.90 2469 3 2 .
47 36.88 12891 1.77 2293 3 6 .
43 40.36 14194 1.65 2249 4 0 .
38 45.66 16021 1.48 2277 4 5 .
33 51.54 18070 1.31 3005 5 0 .
28 62.47 21883 1.08 2405 6 3 .
24 72.86 25489 0.93 2234 7 1 .
22 80.03 27994 0.85 2103 8 0 .

38 44.89 15720 2.13 7643 K 0 9 3 1 4 5 . _ N _ _ _ _ 1 0 . B - - 526 215TC
35 49.87 17454 1.92 7643 5 0 .
32 54.09 18918 1.97 7643 5 6 .
29 60.10 21036 1.77 7643 6 3 .
24 70.45 24572 1.36 7643 7 1 .
22 77.78 27273 1.23 7643 8 0 .
20 84.89 29609 1.26 7643 9 0 .
18 93.71 32701 1.14 7643 1 0 0
16 106.99 37384 0.89 7643 1 1 2

34 50.41 17716 3.62 11205 K 1 0 3 1 5 0 . _ N _ _ _ _ 1 0 . B - - 801.6 215TC
32 54.61 19111 3.36 11200 5 6 .
28 60.68 21291 3.01 11200 6 3 .
24 71.89 25283 2.54 11194 7 1 .
21 82.83 29067 2.21 11189 8 0 .
20 86.53 30339 2.11 11189 9 0 .
17 99.70 34923 1.84 11190 1 0 0
15 112.03 39147 1.64 11180 1 1 2
14 120.36 42211 1.52 11178 1 2 5
13 134.85 47129 1.36 11165 1 4 0
12 144.88 50461 1.27 11195 1 6 0

10 166.84 57315 1.15 11159 K 1 0 5 1 1 6 0 _ N _ _ _ _ 1 0 . B - - 861.1 215TC
7.5 231.10 79399 0.83 11159 2 0 0

21 83.10 29038 3.69 16259 K 1 2 3 1 8 0 . _ N _ _ _ _ 1 0 . B - - 1121.3 215TC
19 89.89 31314 3.48 16254 9 0 .
17 100.12 34896 3.12 16241 1 0 0
NOTE 15 113.79 39714 2.70 16235 1 1 2
14 121.06 42417 2.52 16229 1 2 5
Other output 13 137.09 47881 2.27 16247 1 4 0
12 145.85 50837 2.14 16248 1 6 0
speeds are

available 10 172.15 59296 1.81 16198 K 1 2 5 1 1 6 0 _ N _ _ _ _ 1 0 . B - - 1213.8 215TC
using 6 and 8 6.4 268.79 92469 1.16 16198 2 0 0
pole motors 7.2 238.46 82140 1.30 16198 2 5 0
- Consult 5.7 301.94 103874 1.03 16198 2 8 0
Application 5.2 331.99 114220 0.94 16198 3 2 0
Engineering 4.5 384.70 132501 0.81 16198 3 6 0

51
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
15.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
205 8.60 4410 1.42 1813 K 0 7 3 2 8 . 0 _ N _ _ _ _ 1 5 . B - - 392.1 254TC
4 POLE 148 11.91 6130 1.42 1818 1 1 .
132 13.37 6915 1.42 1833 1 2 .
120 14.71 7586 1.41 1845 1 4 .
92 19.21 9995 1.17 1834 1 8 .
81 21.84 11345 1.06 1820 2 0 .

217 8.13 4192 2.85 2072 K 0 8 3 2 8 . 0 _ N _ _ _ _ 1 5 . B - - 515.6 254TC
153 11.52 5938 2.74 2038 1 1 .
138 12.80 6585 2.61 2047 1 2 .
124 14.24 7364 2.46 2050 1 4 .
96 18.41 9501 2.07 2021 1 8 .
85 20.67 10691 1.88 1993 2 0 .
69 25.35 13125 1.59 1974 2 5 .
62 28.56 14735 1.45 1910 2 8 .
53 33.24 17089 1.29 1873 3 2 .
48 36.88 18952 1.20 1705 3 6 .
44 40.36 20868 1.12 1601 4 0 .
39 45.66 23554 1.01 1456 4 5 .
34 51.54 26567 0.89 2540 5 0 .

98 17.93 9243 3.25 7643 K 0 9 3 1 1 8 . _ N _ _ _ _ 1 5 . B - - 639 254TC
88 20.03 10319 2.98 7643 2 0 .
81 21.61 11122 3.18 7643 2 2 .
73 24.14 12426 2.91 7643 2 5 .
63 27.78 14342 2.30 7643 2 8 .
56 31.67 16348 2.04 7643 3 2 .
53 33.47 17195 2.17 7643 3 6 .
46 38.16 19640 1.90 7643 4 0 .
39 44.89 23111 1.45 7643 4 5 .
35 49.87 25661 1.30 7643 5 0 .
33 54.09 27813 1.34 7643 5 6 .
29 60.10 30927 1.20 7643 6 3 .
25 70.45 36125 0.93 7643 7 1 .
23 77.78 40096 0.83 7643 8 0 .
21 84.89 43531 0.86 7643 9 0 .

53 33.10 17114 3.75 11217 K 1 0 3 1 3 2 . _ N _ _ _ _ 1 5 . B - - 914.6 254TC
50 35.19 18159 3.53 11217 3 6 .
44 39.84 20566 3.12 11217 4 0 .
39 45.37 23476 2.73 11034 4 5 .
35 50.41 26046 2.46 11196 5 0 .
32 54.61 28097 2.28 11188 5 6 .
29 60.68 31301 2.05 11187 6 3 .
24 71.89 37170 1.73 11178 7 1 .
21 82.83 42734 1.50 11168 8 0 .
20 86.53 44604 1.44 11168 9 0 .
18 99.70 51343 1.25 11170 1 0 0
16 112.03 57554 1.11 11154 1 1 2
15 120.36 62058 1.03 11150 1 2 5
13 134.85 69288 0.93 11128 1 4 0

33 52.76 27256 3.93 16264 K 1 2 3 1 5 0 . _ N _ _ _ _ 1 5 . B - - 1234.3 254TC
31 56.39 29035 3.75 16257 5 6 .
28 63.57 32723 3.33 16252 6 3 .
24 74.62 38298 2.80 16235 7 1 .
21 83.10 42691 2.51 16247 8 0 .
20 89.89 46037 2.36 16239 9 0 .
18 100.12 51304 2.12 16216 1 0 0
15 113.79 58386 1.83 16206 1 1 2
15 121.06 62360 1.72 16196 1 2 5
13 137.09 70394 1.55 16227 1 4 0
12 145.85 74739 1.46 16228 1 6 0

10 172.15 87175 1.23 16198 K 1 2 5 1 1 6 0 _ N _ _ _ _ 1 5 . B - - 1326.8 254TC
7.4 238.46 120760 0.89 16198 2 5 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

52
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
20.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
205 8.60 5881 1.07 1649 K 0 7 3 2 8 . 0 _ N _ _ _ _ 2 0 . B - - 419.1 256TC
4 POLE 148 11.91 8174 1.07 1591 1 1 .
132 13.37 9220 1.07 1577 1 2 .
120 14.71 10115 1.06 1562 1 4 .
92 19.21 13326 0.88 1469 1 8 .

217 8.13 5589 2.14 1971 K 0 8 3 2 8 . 0 _ N _ _ _ _ 2 0 . B - - 542.6 256TC
153 11.52 7918 2.06 1894 1 1 .
138 12.80 8780 1.96 1888 1 2 .
124 14.24 9819 1.85 1874 1 4 .
96 18.41 12668 1.55 1795 1 8 .
85 20.67 14255 1.41 1737 2 0 .
69 25.35 17500 1.19 1588 2 5 .
62 28.56 19646 1.09 1469 2 8 .
53 33.24 22786 0.97 1276 3 2 .
48 36.88 25270 0.90 1118 3 6 .
44 40.36 27825 0.84 952 4 0 .

219 8.03 5508 3.90 7010 K 0 9 3 1 8 . 0 _ N _ _ _ _ 2 0 . B - - 666 256TC
182 9.68 6619 3.90 7161 1 0 .
159 11.06 7611 3.29 7216 1 1 .
142 12.40 8539 3.09 7303 1 2 .
132 13.33 9144 3.29 7392 1 4 .
118 14.94 10259 3.09 7386 1 6 .
98 17.93 12325 2.43 7354 1 8 .
88 20.03 13759 2.23 7437 2 0 .
81 21.61 14830 2.39 7447 2 2 .
73 24.14 16568 2.18 7431 2 5 .
63 27.78 19123 1.73 7477 2 8 .
56 31.67 21797 1.53 7643 3 2 .
53 33.47 22927 1.63 7643 3 6 .
46 38.16 26187 1.42 7643 4 0 .
39 44.89 30815 1.09 7643 4 5 .
35 49.87 34215 0.98 7643 5 0 .
33 54.09 37084 1.00 7643 5 6 .
29 60.10 41236 0.90 7643 6 3 .

73 24.13 16606 3.86 11028 K 1 0 3 1 2 5 . _ N _ _ _ _ 2 0 . B - - 941.6 256TC
60 29.24 20160 3.18 11015 2 8 .
53 33.10 22819 2.81 11005 3 2 .
50 35.19 24212 2.65 11022 3 6 .
44 39.84 27422 2.34 11147 4 0 .
39 45.37 31301 2.05 10957 4 5 .
35 50.41 34728 1.85 11186 5 0 .
32 54.61 37463 1.71 11176 5 6 .
29 60.68 41735 1.54 11175 6 3 .
24 71.89 49560 1.29 11161 7 1 .
21 82.83 56979 1.13 11148 8 0 .
20 86.53 59472 1.08 11148 9 0 .
18 99.70 68457 0.94 11150 1 0 0
16 112.03 76738 0.84 11128 1 1 2

44 39.55 27223 4.00 16260 K 1 2 3 1 4 0 . _ N _ _ _ _ 2 0 . B - - 1261.3 256TC
38 46.81 32213 3.32 16159 4 5 .
33 52.76 36341 2.95 16260 5 0 .
31 56.39 38714 2.81 16249 5 6 .
28 63.57 43631 2.50 16242 6 3 .
24 74.62 51065 2.10 16219 7 1 .
21 83.10 56922 1.88 16234 8 0 .
20 89.89 61383 1.77 16224 9 0 .
18 100.12 68405 1.59 16191 1 0 0
15 113.79 77849 1.38 16177 1 1 2
15 121.06 83147 1.29 16162 1 2 5
13 137.09 93859 1.16 16206 1 4 0
12 145.85 99652 1.09 16208 1 6 0

10 172.15 116233 0.92 16198 K 1 2 5 1 1 6 0 _ N _ _ _ _ 2 0 . B - - 1353.8 256TC

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

53
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
25.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
219 8.03 6885 3.12 6850 K 0 9 3 1 8 . 0 _ N _ _ _ _ 2 5 . B - - 815.3 284TC
4 POLE 182 9.68 8273 3.12 6972 1 0 .
159 11.06 9514 2.63 6991 1 1 .
142 12.40 10674 2.47 7052 1 2 .
132 13.33 11430 2.63 7142 1 4 .
118 14.94 12824 2.47 7129 1 6 .
98 17.93 15406 1.95 7065 1 8 .
88 20.03 17199 1.79 7232 2 0 .
81 21.61 18538 1.91 7251 2 2 .
73 24.14 20710 1.75 7219 2 5 .
63 27.78 23904 1.38 7310 2 8 .
56 31.67 27247 1.22 7643 3 2 .
53 33.47 28659 1.30 7643 3 6 .
46 38.16 32734 1.14 7643 4 0 .
39 44.89 38519 0.87 7643 4 5 .

95 18.57 16009 3.79 10649 K 1 0 3 1 1 8 . _ N _ _ _ _ 2 5 . B - - 1090.9 284TC
88 20.05 17272 3.58 10781 2 0 .
79 22.35 19215 3.34 10826 2 2 .
73 24.13 20758 3.09 10838 2 5 .
60 29.24 25200 2.55 10813 2 8 .
53 33.10 28524 2.25 10793 3 2 .
50 35.19 30266 2.12 10826 3 6 .
44 39.84 34278 1.87 11076 4 0 .
39 45.37 39126 1.64 10881 4 5 .
35 50.41 43410 1.48 11177 5 0 .
32 54.61 46828 1.37 11164 5 6 .
29 60.68 52169 1.23 11163 6 3 .
24 71.89 61950 1.04 11144 7 1 .
21 82.83 71224 0.90 11128 8 0 .
20 86.53 74340 0.86 11128 9 0 .

54 32.83 28359 3.78 15990 K 1 2 3 1 3 2 . _ N _ _ _ _ 2 5 . B - - 1375.3 284TC
50 34.93 30029 3.63 15812 3 6 .
44 39.55 34029 3.20 16255 4 0 .
38 46.81 40266 2.66 16125 4 5 .
33 52.76 45426 2.36 16255 5 0 .
31 56.39 48392 2.25 16241 5 6 .
28 63.57 54539 2.00 16232 6 3 .
24 74.62 63831 1.68 16202 7 1 .
21 83.10 71152 1.51 16222 8 0 .
20 89.89 76728 1.42 16209 9 0 .
18 100.12 85507 1.27 16166 1 0 0
15 113.79 97311 1.10 16147 1 1 2
15 121.06 103934 1.03 16129 1 2 5
13 137.09 117323 0.93 16186 1 4 0

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

54
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
30.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
219 8.03 8262 2.60 6689 K 0 9 3 1 8 . 0 _ N _ _ _ _ 3 0 . B - - 809.3 286TC
4 POLE 182 9.68 9928 2.60 6782 1 0 .
159 11.06 11417 2.19 6766 1 1 .
142 12.40 12809 2.06 6801 1 2 .
132 13.33 13716 2.19 6891 1 4 .
118 14.94 15388 2.06 6872 1 6 .
98 17.93 18487 1.62 6776 1 8 .
88 20.03 20639 1.49 7026 2 0 .
81 21.61 22245 1.59 7055 2 2 .
73 24.14 24852 1.46 7007 2 5 .
63 27.78 28685 1.15 7144 2 8 .
56 31.67 32696 1.02 7643 3 2 .
53 33.47 34391 1.08 7643 3 6 .
46 38.16 39281 0.95 7643 4 0 .

140 12.55 12983 3.97 9634 K 1 0 3 1 1 2 . _ N _ _ _ _ 3 0 . B - - 1084.9 286TC
116 15.11 15611 3.97 10141 1 6 .
95 18.57 19211 3.16 10443 1 8 .
88 20.05 20726 2.98 10562 2 0 .
79 22.35 23058 2.78 10630 2 2 .
73 24.13 24910 2.58 10649 2 5 .
60 29.24 30240 2.12 10610 2 8 .
53 33.10 34228 1.87 10581 3 2 .
50 35.19 36319 1.77 10630 3 6 .
44 39.84 41133 1.56 11005 4 0 .
39 45.37 46952 1.37 10804 4 5 .
35 50.41 52092 1.23 11168 5 0 .
32 54.61 56194 1.14 11152 5 6 .
29 60.68 62602 1.03 11150 6 3 .
24 71.89 74340 0.86 11128 7 1 .

61 28.99 30002 3.57 15625 K 1 2 3 1 2 8 . _ N _ _ _ _ 3 0 . B - - 1369.3 286TC
54 32.83 34031 3.15 15847 3 2 .
50 34.93 36035 3.02 15706 3 6 .
44 39.55 40835 2.67 16250 4 0 .
38 46.81 48320 2.22 16090 4 5 .
33 52.76 54512 1.96 16250 5 0 .
31 56.39 58071 1.87 16233 5 6 .
28 63.57 65447 1.66 16222 6 3 .
24 74.62 76597 1.40 16185 7 1 .
21 83.10 85383 1.25 16210 8 0 .
20 89.89 92074 1.18 16194 9 0 .
18 100.12 102608 1.06 16141 1 0 0
15 113.79 116773 0.92 16118 1 1 2
15 121.06 124721 0.86 16096 1 2 5

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

55
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
40.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
219 8.03 11016 1.95 6368 K 0 9 3 1 8 . 0 _ N _ _ _ _ 4 0 . B - - 920.3 324TC
4 POLE 182 9.68 13238 1.95 6403 1 0 .
159 11.06 15222 1.65 6316 1 1 .
142 12.40 17079 1.54 6300 1 2 .
132 13.33 18288 1.65 6390 1 4 .
118 14.94 20518 1.54 6358 1 6 .
98 17.93 24650 1.22 6198 1 8 .
88 20.03 27518 1.12 6615 2 0 .
81 21.61 29661 1.19 6663 2 2 .
73 24.14 33136 1.09 6583 2 5 .
63 27.78 38247 0.86 6811 2 8 .

213 8.26 11373 3.18 9181 K 1 0 3 1 8 . 0 _ N _ _ _ _ 4 0 . B - - 1195.9 324TC
177 9.95 13653 3.18 9358 1 0 .
152 11.54 15920 3.12 9406 1 1 .
140 12.55 17311 2.98 9448 1 2 .
127 13.89 19127 3.12 9573 1 4 .
116 15.11 20815 2.98 9814 1 6 .
95 18.57 25615 2.37 10032 1 8 .
88 20.05 27635 2.24 10125 2 0 .
79 22.35 30745 2.09 10238 2 2 .
73 24.13 33213 1.93 10270 2 5 .
60 29.24 40320 1.59 10206 2 8 .
53 33.10 45638 1.41 10157 3 2 .
50 35.19 48425 1.33 10238 3 6 .
44 39.84 54845 1.17 10864 4 0 .
39 45.37 62602 1.03 10651 4 5 .
35 50.41 69457 0.92 11150 5 0 .
32 54.61 74926 0.86 11128 5 6 .

207 8.51 11731 3.81 14145 K 1 2 3 1 8 . 0 _ N _ _ _ _ 4 0 . B - - 1493.5 324TC
172 10.26 14123 3.81 14513 1 0 .
149 11.80 16307 3.81 14612 1 1 .
136 12.96 17933 3.81 14726 1 2 .
124 14.21 19606 3.81 14969 1 4 .
113 15.61 21557 3.81 15182 1 6 .
97 18.20 25088 3.81 15304 1 8 .
87 20.17 27876 3.81 15304 2 0 .
80 21.93 30175 3.61 15396 2 2 .
72 24.29 33458 3.25 15383 2 5 .
61 28.99 40003 2.68 15191 2 8 .
54 32.83 45375 2.36 15562 3 2 .
50 34.93 48046 2.27 15495 3 6 .
44 39.55 54447 2.00 16241 4 0 .
38 46.81 64427 1.66 16022 4 5 .
33 52.76 72683 1.47 16241 5 0 .
31 56.39 77428 1.41 16217 5 6 .
28 63.57 87263 1.25 16203 6 3 .
24 74.62 102130 1.05 16152 7 1 .
21 83.10 113844 0.94 16186 8 0 .
20 89.89 122766 0.89 16163 9 0 .

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

56
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
50.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
219 8.03 13771 1.56 6047 K 0 9 3 1 8 . 0 _ N _ _ _ _ 5 0 . B - - 1073.3 326TC
4 POLE 182 9.68 16547 1.56 6024 1 0 .
159 11.06 19028 1.32 5867 1 1 .
142 12.40 21349 1.24 5799 1 2 .
132 13.33 22861 1.32 5889 1 4 .
118 14.94 25648 1.24 5844 1 6 .
98 17.93 30812 0.97 5619 1 8 .
88 20.03 34398 0.89 6204 2 0 .
81 21.61 37076 0.95 6271 2 2 .
73 24.14 41420 0.87 6159 2 5 .

213 8.26 14216 2.55 9059 K 1 0 3 1 8 . 0 _ N _ _ _ _ 5 0 . B - - 1348.9 326TC
177 9.95 17066 2.55 9217 1 0 .
152 11.54 19900 2.50 9239 1 1 .
140 12.55 21639 2.38 9262 1 2 .
127 13.89 23908 2.50 9374 1 4 .
116 15.11 26019 2.38 9486 1 6 .
95 18.57 32019 1.90 9621 1 8 .
88 20.05 34544 1.79 9688 2 0 .
79 22.35 38431 1.67 9846 2 2 .
73 24.13 41516 1.55 9891 2 5 .
60 29.24 50400 1.27 9801 2 8 .
53 33.10 57048 1.12 9733 3 2 .
50 35.19 60532 1.06 9846 3 6 .
44 39.84 68556 0.94 10723 4 0 .
39 45.37 78253 0.82 10498 4 5 .

207 8.51 14664 3.05 13950 K 1 2 3 1 8 . 0 _ N _ _ _ _ 5 0 . B - - 1646.5 326TC
172 10.26 17654 3.05 14293 1 0 .
149 11.80 20384 3.05 14342 1 1 .
136 12.96 22417 3.05 14430 1 2 .
124 14.21 24507 3.05 14662 1 4 .
113 15.61 26946 3.05 14843 1 6 .
97 18.20 31360 3.05 14915 1 8 .
87 20.17 34845 3.05 14915 2 0 .
80 21.93 37719 2.89 15044 2 2 .
72 24.29 41823 2.60 15026 2 5 .
61 28.99 50003 2.14 14757 2 8 .
54 32.83 56718 1.89 15276 3 2 .
50 34.93 60058 1.81 15284 3 6 .
44 39.55 68059 1.60 16232 4 0 .
38 46.81 80533 1.33 15953 4 5 .
33 52.76 90853 1.18 16232 5 0 .
31 56.39 96785 1.12 16202 5 6 .
28 63.57 109079 1.00 16183 6 3 .
24 74.62 127662 0.84 16118 7 1 .

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

57
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
60.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.51 17596 2.54 13754 K 1 2 3 1 8 . 0 _ N _ _ _ _ 6 0 . B - - 1646.5 364TC
4 POLE 172 10.26 21185 2.54 14074 1 0 .
149 11.80 24461 2.54 14072 1 1 .
136 12.96 26900 2.54 14133 1 2 .
124 14.21 29409 2.54 14355 1 4 .
113 15.61 32336 2.54 14505 1 6 .
97 18.20 37632 2.54 14526 1 8 .
87 20.17 41814 2.54 14526 2 0 .
80 21.93 45262 2.41 14693 2 2 .
72 24.29 50187 2.17 14669 2 5 .
61 28.99 60004 1.78 14324 2 8 .
54 32.83 68062 1.57 14990 3 2 .
50 34.93 72070 1.51 15073 3 6 .
44 39.55 81671 1.33 16222 4 0 .
38 46.81 96640 1.11 15884 4 5 .
33 52.76 109024 0.98 16222 5 0 .
31 56.39 116142 0.94 16186 5 6 .
28 63.57 130895 0.83 16163 6 3 .

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

58
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
75.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.51 21996 2.03 13460 K 1 2 3 1 8 . 0 _ N _ _ _ _ 7 5 . B - - 1743.5 365TC
4 POLE 172 10.26 26482 2.03 13745 1 0 .
149 11.80 30576 2.03 13668 1 1 .
136 12.96 33625 2.03 13689 1 2 .
124 14.21 36761 2.03 13895 1 4 .
113 15.61 40420 2.03 13997 1 6 .
97 18.20 47040 2.03 13943 1 8 .
87 20.17 52267 2.03 13943 2 0 .
80 21.93 56578 1.92 14165 2 2 .
72 24.29 62734 1.74 14133 2 5 .
61 28.99 75005 1.43 13673 2 8 .
54 32.83 85078 1.26 14562 3 2 .
50 34.93 90087 1.21 14757 3 6 .
44 39.55 102089 1.07 16208 4 0 .
38 46.81 120800 0.89 15781 4 5 .

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

59
 SERIES K
SELECTION TABLES
GEARED MOTORS
N2 M2
100.00 HP R/MIN
i
lb.in
Fm N Unit Designation Kg

Output Service Overhung Weight of Motor

Output Column Entry 1 Through 20
Ratio base
Speed Torque Factor Load Size
Spaces to be filled when entering order mount unit
207 8.51 29328 1.52 12971 K 1 2 3 1 8 . 0 _ N _ _ _ _ 1 0 0 B - - 2227.4 405TC
4 POLE 172 10.26 35309 1.52 13196 1 0 .
149 11.80 40768 1.52 12993 1 1 .
136 12.96 44834 1.52 12948 1 2 .
124 14.21 49015 1.52 13128 1 4 .
113 15.61 53893 1.52 13151 1 6 .
97 18.20 62721 1.52 12971 1 8 .
87 20.17 69690 1.52 12971 2 0 .
80 21.93 75438 1.44 13286 2 2 .
72 24.29 83646 1.30 13241 2 5 .
61 28.99 100007 1.07 12589 2 8 .
54 32.83 113437 0.94 13848 3 2 .
50 34.93 120117 0.91 14230 3 6 .

NOTE

Other output
speeds are
available
using 6 and 8
pole motors
- Consult
Application
Engineering

60
 SERIES K
DIMENSIONS
TRIPLE REDUCTION
w7
k1 k0 o o
z
q q1 e
a
n0

g6

g
h1

y
4
b0
f0

p3
Holes
øs

h
m1
m2
a3

Setscrews
v3

U
n c

øD
a2

m3
b
m m T
f
Output Shaft Bore

Size a a2 a3 b b0 c e f f0 h h1 n n0 o p3
K0332 3.94 1.10 1.26 4.33 4.53 0.43 4.72 5.63 5.98 3.94 0.63 1.50 1.50 2.36 6.57
K0432 4.72 1.38 1.46 5.12 5.12 0.63 5.71 6.61 6.73 4.41 0.51 1.50 1.57 2.95 7.36
K0532 5.12 1.18 1.77 5.12 5.91 0.59 6.18 6.69 7.56 5.20 0.20 1.57 1.57 3.27 8.54
K0632 5.51 1.18 1.77 4.72 6.30 0.79 6.69 6.93 8.19 5.51 0.51 2.17 1.89 3.54 9.17
K0732 6.50 1.57 2.17 5.91 7.87 1.06 7.87 8.27 10.35 7.09 0.98 2.36 2.17 4.13 11.34
K0832 7.09 2.17 2.76 7.09 9.17 1.18 9.06 10.08 12.17 8.35 0.59 2.99 2.99 4.72 13.43
K0931 9.45 2.95 2.95 9.45 11.61 1.38 11.42 13.39 15.55 10.43 0.39 3.94 3.94 5.91 16.54
K1031 10.63 3.74 3.74 11.02 14.17 1.57 13.39 15.35 17.91 12.40 1.61 4.33 4.53 6.89 20.20
K1231 12.99 4.53 4.33 13.78 16.54 1.77 15.75 18.50 21.26 14.76 2.56 4.72 4.72 8.07 23.23

Hollow Output Bore

Size q q1 s w7 y z
D m m1 m2 m3 T U v3
K0332 2.48 6.26 0.43 2.48 5.51 0.00 1.18 2.067 4.724 4.134 1.193 1.319 0.315 3/8 UNF x 2 long
K0432 2.80 7.05 0.43 3.07 5.51 0.10 1.38 2.598 5.906 5.197 1.390 1.516 0.394 1/2 UNF x 21/4 long
K0532 3.15 8.62 0.55 3.43 7.09 0.18 1.57 2.874 6.535 5.591 1.587 1.713 0.472 5/8 UNF x 23/4 long
K0632 3.54 9.02 0.55 3.70 7.09 0.20 1.57 3.150 7.087 6.142 1.587 1.713 0.472 5/8 UNF x 23/4 long
K0732 4.41 10.43 0.71 4.29 8.35 0.20 1.97 3.642 8.268 7.205 1.988 2.126 0.551 5/8 UNF x 23/4 long
K0832 5.20 12.99 0.91 4.88 9.84 0.20 2.36 4.134 9.449 8.268 2.382 2.539 0.709 3/4-16 UNF x 31/4 long
K0931 6.30 13.98 1.06 6.06 11.81 0.20 2.76 5.217 11.811 10.630 2.776 2.953 0.787 3/4-16 UNF x 31/4 long
K1031 7.87 16.65 1.34 7.09 14.17 0.20 3.15 6.102 13.780 12.323 3.169 3.366 0.866 3/4-16 UNF x 31/4 long
K1231 8.86 18.74 1.54 8.27 15.75 0.20 3.94 7.087 16.142 14.685 3.957 4.193 1.102 1-12 UNF x 41/2 long

MOTOR K0332 K0432 K0532 K0632 K0732 K0832 K0931 K1031 K1231
FRAME
SIZE K1 K1 K1 K1 K1 K1 K1 K1 K1
56C 11.30 12.40 13.74 14.53 16.89 21.69 - - -
143-145TC 11.30 12.40 13.74 14.53 16.89 21.69 - - -
182-184TC 10.98 12.09 14.72 15.51 17.24 21.69 22.80 26.89 31.61
213-215TC - - 14.72 15.51 17.24 21.69 22.80 26.89 31.61
254-256TC - - - - 17.17 21.69 24.17 28.07 31.61
284-286TC - - - - - - 24.29 28.19 31.73
324-326TC - - - - - - 24.96 28.82 32.36
364-365TC - - - - - - - - 39.06
404-405TC - - - - - - - - 40.43

61
 SERIES K
DIMENSIONS
QUINTUPLE REDUCTION
w7
k1 o o
q q1 ko z
e
a
n0

v3

g6

g
h1

y
b0
f0

p3
v2
Holes
øs

h
m1
a3

m2
n
c

a2 Setscrews
U v3
b

øD
f

m3
T m m
Output Shaft Bore

Size a a2 a3 b b0 c e f f0 h h1 n n0 o p3 q
K0532 3.94 1.10 1.26 4.33 4.53 0.43 4.72 5.63 5.98 3.94 0.63 1.50 1.50 2.36 6.57 2.48
K0452 4.72 1.38 1.46 5.12 5.12 0.63 5.71 6.61 6.73 4.41 0.51 1.50 1.57 2.95 7.36 2.80
K0552 5.12 1.18 1.77 5.12 5.91 0.59 6.18 6.69 7.56 5.20 0.20 1.57 1.57 3.27 8.54 3.15
K0652 5.51 1.18 1.77 4.72 6.30 0.79 6.69 6.93 8.19 5.51 0.51 2.17 1.89 3.54 9.17 3.54
K0752 6.50 1.57 2.17 5.91 7.87 1.06 7.87 8.27 10.35 7.09 0.98 2.36 2.17 4.13 11.34 4.41
K0852 7.09 2.17 2.76 7.09 9.17 1.18 9.06 10.08 12.17 8.35 0.59 2.99 2.99 4.72 13.43 5.20
K0951 9.45 2.95 2.95 9.45 11.61 1.38 11.42 13.39 15.55 10.43 0.39 3.94 3.94 5.91 16.54 6.30
K1051 10.63 3.74 3.74 11.02 14.17 1.57 13.39 15.35 17.91 12.40 1.61 4.33 4.53 6.89 20.20 7.87
K1251 12.99 4.53 4.33 13.78 16.54 1.77 15.75 18.50 21.26 14.76 2.56 4.72 4.72 8.07 23.23 8.86

Hollow Output Bore

Size q1 s v2 v3 w7 y z
D m m1 m2 m3 T U v3
K0332 6.26 0.43 2.99 - 2.48 5.51 0.00 1.181 2.067 4.724 4.134 1.193 1.319 0.315 3/8 UNF x 2 long
K0432 7.05 0.43 2.99 - 3.07 5.51 0.10 1.378 2.598 5.906 5.197 1.390 1.516 0.394 1/2 UNF x 21/4 long
K0532 8.62 0.53 3.58 - 3.43 7.09 0.18 1.575 2.874 6.535 5.591 1.587 1.713 0.472 5/8 UNF x 23/4 long
K0632 9.02 0.55 3.58 - 3.70 7.09 0.20 1.575 3.150 7.087 6.142 1.587 1.713 0.472 5/8 UNF x 23/4 long
K0732 10.43 0.71 3.58 - 4.29 8.35 0.20 1.969 3.642 8.268 7.205 1.988 2.126 0.551 5/8 UNF x 23/4 long
K0832 12.99 0.91 4.53 - 4.88 9.84 0.20 2.362 4.134 9.449 8.268 2.382 2.539 0.709 3/4-16 UNF x 31/4 long
K0931 13.98 1.06 4.53 - 6.06 11.81 0.20 2.756 5.217 11.811 10.630 2.776 2.953 0.787 3/4-16 UNF x 31/4 long
K1031 16.65 1.34 5.51 6.10 7.09 14.17 0.20 3.150 6.102 13.780 12.323 3.169 3.366 0.866 3/4-16 UNF x 31/4 long
K1231 18.74 1.54 5.51 6.10 8.27 15.75 0.20 3.937 7.087 16.142 14.685 3.957 4.193 1.102 1-12 UNF x 41/2 long

MOTOR K0352 K0452 K0552 K0652 K0752 K0852 K0951 K1051 K1251
FRAME
SIZE K1 K1 K1 K1 K1 K1 K1 K1 K1
56C 18.62 19.72 22.28 23.07 25.39 29.80 32.32 38.07 43.07
143-145TC 18.62 31.72 22.28 23.07 25.39 29.80 32.32 38.07 43.07
182-184TC 18.31 34.91 21.97 22.76 25.08 30.79 33.31 38.43 43.43
213-215TC - - - - - 30.79 33.31 38.43 43.43
254-256TC - - - - - - - 38.35 43.35

62
 SERIES K
DIMENSIONS
OUTPUT OPTIONS

Single Extended Outputshaft Double Extended Outputshaft

See Page 82 See Page 82

Shrink Disc Taper Release Bushing

See Page 83 See Page 84

Torque Bracket B5 (D) Flange Mounting

See Page 86 See Page 87

B14 (C) Flange Mounting

See Page 88

63
 SERIES K
MOTORIZED
BACKSTOP MODULE
Motorized backstop modules can be fitted between the gear unit and motor. The backstop device incorporates high quality centrifugal lift
off sprags which are wear free above the lift off speed (n min).

To ensure correct operation motor speed must exceed lift off speed.

Suitable for ambient temperature -220oF to + 122oF

K1

øg6
Warning
Removal of motor or backstop will release the drive. Ensure
all driven machinery is secure prior to any maintenance work

IEC B5 FLANGE

Motor Frame Lift off min)

Speed (‘n’ Rated Locking
Torque (‘T max’) øg6 K1
Size (rev/min) (at motor) (lb.in)

100 670 1505 9.84 2.76

112 670 1505 9.84 2.76
132 620 8319 11.81 3.74
160 620 8319 13.78 5.12
180 620 8319 13.78 5.12
200 550 11151 15.75 5.12

NEMA C FLANGE

Lift off Speed Rated Locking

Motor Frame (‘n’ min) Torque (‘T max’) øg6 K1
Size (rev/min) (at motor) (Nm)

182TC / 184TC 670 2655 8.98 3.75

213TC / 215TC 670 2655 8.98 3.75
254TC / 256TC 620 8319 8.98 4.75
284TC / 286TC 620 8319 11.02 5.37
324TC / 326TC 550 11151 12.99 6.00

When a backstop module is fitted dimension K1 should be added to the overall length of the geared motor assembly.

Rotation of outputshaft must be specified when ordering as viewed from the outputshaft end (as shown in
the diagram) see page 28 for column 20 entry

CW - Free Rotation - Clockwise

Locked - Anticlockwise

AC - Free Rotation - Anticlockwise

Locked - Clockwise
CW

64
 SERIES K

REDUCER

SERIES K
 SERIES K
OVERHUNG & AXIAL LOADS
(lbf) ON SHAFTS
Maximum permissible overhung loads
When a sprocket, gear etc. is mounted on the shaft a calculation, as below, must be made to determine the overhung load on the shaft, and the
results compared to the maximum permissible overhung loads tabulated. Overhung loads can be reduced by increasing the diameter of the
sprocket, gear, etc. If the maximum permissible overhung load is exceeded, the sprocket, gear, etc. should be mounted on a separate shaft,
flexibly coupled and supported in its own bearings, or the gear unit shaft should be extended to run in an outboard bearing. Alternatively, a larger
gear is often a less expensive solution.

Permissible overhung loads vary according to the direction of rotation. The values tabulated are for the most unfavourable direction with the unit
transmitting full rated power and the load P applied midway along the shaft extension. Hence they can sometimes be increased for a more
favourable direction of rotation, or if the power transmitted is less than the rated capacity of the gear unit, or if the load is applied nearer to the gear
unit case. Refer to Application Engineering for further details. In any event, the sprocket, gear etc. should be positioned as close as possible to
the gear unit case in order to reduce bearing loads and shaft stresses, and to prolong life.

All units will accept 100% momentary overload on stated capacities.

Overhung load (lbf) Overhung member K (factor)

Chain sprocket* 1.00
HP x 63,000 x K
P= Spur or helical pinion 1.25
NxR
Vee belt sheave 1.50
Where Flat belt pulley 2.00

P = equivalent overhung load (lbf)

* If multistrand chain drives are equally loaded and the
HP = power transmitted by the shaft (Horse Power)
outer strand is further than dimension A output or B
N = speed of shaft (rev/min)
input, refer to Application Engineering.
R = pitch radius of sprocket, etc. (inches)
K = factor
Distance Midway Along
Note: 1 lbf = 4.4484 Newtons. The Shaft Extension
Frb Size of NO of Dimension A Dimension B
unit Reductions (inches) (inches)

3 0.93 0.79
B K03
5 0.93 0.79
3 1.10 0.79
K04
5 1.10 0.79
3 1.30 0.79
K05
5 1.30 0.79
Input 3 1.50 0.79
K06
5 1.50 0.79
3 1.87 0.98
K07
5 1.87 0.79
Fra 3 1.97 1.18
K08
5 1.97 0.79
3 2.17 1.57
A K09
5 2.17 0.79
3 2.76 2.17
K10
5 2.76 0.98

K12 3 3.54 2.17

5 3.54 0.98
Output
Inputshaft Overhung Loads, Frb (lbf) 1750 rpm
Two, Three and Five Stage Units
Axial Thrust Capacities (Newtons) K03 K04 K05 K06 K07 K08 K09 K10 K12
No check or calculation is required for axial loads (FA) towards or away
3 Stage 338 338 281 236 473 698 788 1013 2700
from the unit up to 50% of the permissible overhung load. If the axial
thrust considerably exceeds these values or if there is a combination of 5 Stage 338 338 338 338 338 338 338 405 405
axial thrust loads and overhung loads please contact Application
Engineering. For output overhung load Fra consult ratings tables pages 31 to 60

66
 SERIES K
TRIPLE REDUCTION RATINGS
SIZES K03 - K05
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
TRIPLE REDUCTION
Input K0332 K0432 K0532
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 420 986 6.88 627 434 1800 13 685 431 2700 19.5 517
1750 210 8.328 1170 4.05 631 217 8.054 2180 7.83 773 215 8.112 3340 11.9 557
8 . 0
1160 139 1270 2.91 741 144 2380 5.63 903 143 3650 8.59 659
875 105 1360 2.34 780 108 2510 4.49 950 107 3870 6.85 680
3500 311 1150 5.91 630 309 2140 11 705 306 3180 16.2 525
1750 155 11.25 1320 3.38 691 154 11.3 2510 6.4 844 153 11.4 3820 9.66 593
1 1 .
1160 103 1450 2.45 809 102 2730 4.6 997 101 4150 6.94 726
875 77 1530 1.95 860 77 2880 3.67 1070 76 4360 5.49 780
3500 273 1200 5.42 630 281 2240 10.4 730 273 3350 15.2 530
1750 136 12.8 1380 3.1 721 140 12.45 2600 6.01 870 136 12.78 3970 8.96 615
1 2 .
1160 90 1510 2.25 845 93 2830 4.33 1030 90 4300 6.41 757
875 68 1600 1.79 912 70 2980 3.44 1100 68 4530 5.09 795
3500 241 1260 5.01 630 247 2360 9.66 745 243 3520 14.3 540
1750 120 14.5 1450 2.87 749 123 14.14 2710 5.53 907 121 14.35 4130 8.29 639
1 4 . 1160 80 1580 2.08 879 82 2950 3.98 1070 80 4460 5.92 788
875 60 1670 1.65 950 61 3110 3.16 1150 60 4700 4.71 840
3500 188 1360 4.23 650 194 2550 8.22 780 192 3870 12.3 550
1750 94 18.54 1580 2.44 813 97 17.95 2940 4.72 982 96 18.22 4440 7.02 698
1 8 .
1160 62 1700 1.75 957 64 3180 3.38 1160 63 4790 5.01 861
875 47 1800 1.39 1040 48 3360 2.69 1250 48 5050 3.98 970
3500 175 1390 4.02 660 171 2660 7.53 800 169 4010 11.3 575
1750 87 19.98 1610 2.32 834 85 20.4 3060 4.32 1030 84 20.66 4590 6.4 737
2 0 . 1160 58 1740 1.66 983 56 3310 3.09 1220 56 4960 4.58 904
875 43 1840 1.32 1080 42 3490 2.46 1350 42 5230 3.64 1030
3500 138 1490 3.4 721 139 2830 6.53 870 142 4220 9.91 605
1750 69 25.23 1720 1.96 907 69 25.03 3250 3.74 1100 71 24.64 4810 5.62 792
2 5 . 1160 45 1860 1.4 1070 46 3510 2.67 1310 47 5200 4.02 971
875 34 1990 1.13 1200 34 3700 2.13 1350 35 5490 3.2 1100
3500 122 1540 3.11 750 126 2910 6.06 910 123 4380 8.94 640
1750 61 28.6 1780 1.79 950 63 27.76 3340 3.46 1150 61 28.37 4990 5.07 840
2 8 .
1160 40 1920 1.28 1120 41 3610 2.48 1350 40 5400 3.63 1030
875 30 1990 0.999 1280 31 3800 1.97 1350 30 5690 2.88 1180
3500 107 1610 2.84 775 110 3010 5.52 940 106 4560 7.99 665
1750 53 32.68 1840 1.62 997 55 31.54 3450 3.15 1200 53 32.99 5180 4.52 897
3 2 . 1160 35 1990 1.16 1170 36 3730 2.26 1350 35 5610 3.24 1100
875 26 1990 0.874 1350 27 3850 1.76 1350 26 5830 2.54 1280
3500 96 1650 2.64 800 97 3210 5.18 982 94 4790 7.51 700
1750 48 36.35 1890 1.5 1040 48 35.83 3660 2.95 1250 47 36.91 5450 4.25 918
3 6 .
1160 31 1990 1.05 1230 32 3910 2.08 1350 31 5830 3.01 1140
875 24 1990 0.788 1350 24 3910 1.57 1350 23 5830 2.27 1340
3500 87 1690 2.44 855 88 3200 4.69 1030 88 4740 6.97 730
1750 43 40.08 1930 1.39 1080 44 39.46 3650 2.67 1310 44 39.34 5410 3.96 968
4 0 . 1160 28 1990 0.947 1290 29 3910 1.89 1350 29 5830 2.82 1180
875 21 1990 0.714 1350 22 3910 1.43 1350 22 5830 2.13 1360
3500 79 1730 2.27 860 77 3310 4.22 1070 75 4930 6.12 770
1750 39 44.11 1980 1.29 1120 38 45.39 3780 2.4 1350 37 46.63 5630 3.48 1040
4 5 .
1160 26 1990 0.861 1350 25 3910 1.64 1350 24 5830 2.39 1320
875 19 1990 0.649 1350 19 3910 1.24 1350 18 5830 1.8 1580
3500 67 1800 2.01 910 70 3380 3.96 1100 70 5010 5.82 790
1750 33 51.68 1990 1.11 1200 35 49.35 3850 2.25 1350 35 49.78 5710 3.31 1070
5 0 . 1160 22 1990 0.735 1350 23 3910 1.51 1350 23 5830 2.24 1380
875 16 1990 0.555 1350 17 3910 1.14 1350 17 5830 1.69 1600
3500 56 1870 1.75 990 59 3520 3.44 1180 56 5260 4.92 875
1750 28 62 1990 0.927 1310 29 59.24 3910 1.91 1350 28 61.78 5830 2.72 1220
6 3 .
1160 18 1990 0.614 1350 19 3910 1.26 1350 18 5830 1.8 1560
875 14 1990 0.463 1350 14 3910 0.952 1350 14 5830 1.36 1700
3500 48 1940 1.56 1040 49 3660 2.99 1250 48 5450 4.33 910
1750 24 72.27 1990 0.796 1350 24 71.09 3820 1.56 1350 24 72.85 5830 2.31 1350
7 1 . 1160 16 1990 0.527 1350 16 3820 1.03 1350 15 5830 1.53 1700
875 12 1990 0.398 1350 12 3820 0.777 1350 12 5830 1.15 1700
3500 43 1980 1.43 1080 43 3760 2.73 1320 43 5560 4.04 970
1750 21 80.3 1990 0.717 1350 21 80.1 3840 1.39 1350 21 79.77 5830 2.11 1430
8 0 . 1160 14 1990 0.475 1350 14 3840 0.92 1350 14 5830 1.4 1700
875 10 1990 0.358 1350 10 3840 0.694 1350 10 5830 1.06 1700
3500 36 1640 0.983 1150 37 3570 2.22 1350 35 5800 3.44 1050
1750 18 96.7 1640 0.492 1350 18 93.12 3570 1.11 1350 17 97.76 5830 1.73 1610
1 0 0
1160 11 1640 0.326 1350 12 3700 0.762 1350 11 5830 1.14 1700
875 9 1640 0.246 1350 9 3790 0.589 1350 8 5830 0.863 1700
3500 31 1410 0.737 1250 33 3640 2 1350 32 5830 3.11 1070
1750 15 110.8 1410 0.369 1350 16 105.7 3650 1 1350 16 109 5830 1.55 1700
1 1 2 1160 10 1410 0.244 1350 10 3780 0.687 1350 10 5830 1.03 1700
875 7 1410 0.184 1350 8 3870 0.531 1350 8 5830 0.775 1700
3500 27 1380 0.639 1350 29 3910 1.89 1350 28 5370 2.56 1220
1750 13 126 1390 0.32 1350 14 120.2 3910 0.944 1350 14 122.2 5380 1.28 1780
1 2 5 1160 9 1390 0.212 1350 9 3910 0.626 1350 9 5380 0.847 1780
875 6 1390 0.16 1350 7 3910 0.472 1350 7 5380 0.639 1780

67
 SERIES K
TRIPLE REDUCTION RATINGS
SIZES K06 - K08
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
TRIPLE REDUCTION
Input K0632 K0732 K0832
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 439 3840 28 785 407 6220 42.3 1080 430 9100 65.7 1160
1750 219 7.961 4740 17.2 856 203 8.595 6270 21.2 1390 215 8.128 9180 32.9 1530
8 . 0
1160 145 5180 12.4 978 134 6290 14 1640 142 9210 21.8 1800
875 109 5480 9.89 990 101 6300 10.6 1640 107 9230 16.4 2000
3500 312 4550 23.6 795 293 8090 39.5 1070 303 13000 65.7 960
1750 156 11.19 5460 14.1 887 146 11.91 8710 21.2 1220 151 11.52 13100 32.9 1270
1 1 .
1160 103 5940 10.1 1070 97 8730 14 1590 100 13100 21.8 1690
875 78 6240 8 1160 73 8740 10.6 1600 75 13100 16.4 1950
3500 279 4800 22.2 815 261 8550 37.1 1070 273 14500 65.7 940
1750 139 12.54 5700 13.1 918 130 13.37 9800 21.2 1170 136 12.8 14500 32.9 1200
1 2 .
1160 92 6160 9.35 1120 86 9810 14 1540 90 14600 21.8 1630
875 69 6500 7.43 1250 65 9820 10.6 1610 68 14600 16.4 1950
3500 248 5060 20.8 835 238 8950 35.4 1080 245 15400 62.9 925
1750 124 14.08 5930 12.1 952 119 14.71 10700 21 1120 122 14.24 16200 32.9 1100
1 4 . 1160 82 6400 8.66 1160 78 10800 14 1500 81 16200 21.8 1550
875 62 6760 6.89 1320 59 10800 10.6 1660 61 16200 16.4 1960
3500 195 5580 18 860 182 10000 30.3 1070 190 17100 54 910
1750 97 17.88 6410 10.3 1030 91 19.21 11600 17.5 1230 95 18.41 19600 30.8 963
1 8 .
1160 64 6910 7.36 1260 60 12500 12.4 1540 63 21000 21.8 1290
875 48 7290 5.85 1450 45 13200 9.87 1710 47 21000 16.4 1440
3500 172 5800 16.5 880 160 10600 28 1070 169 17600 49.4 920
1750 86 20.27 6630 9.41 1090 80 21.84 12000 15.9 1300 84 20.67 20000 28 1040
2 0 . 1160 57 7170 6.74 1320 53 13000 11.3 1610 56 21700 20.1 1350
875 43 7320 5.18 1550 40 13700 9.02 1750 42 23600 16.4 1500
3500 144 6110 14.6 910 131 11200 24.5 1070 138 18300 41.8 930
1750 72 24.18 6980 8.3 1160 65 26.52 12700 13.8 1410 69 25.35 20800 23.7 1190
2 5 . 1160 47 7310 5.76 1450 43 13700 9.9 1730 45 23100 17.4 1470
875 36 7320 4.34 1720 32 14500 7.87 1920 34 23900 13.6 1810
3500 125 6360 13.2 950 119 11500 22.9 1120 122 18700 38 930
1750 62 27.84 7250 7.49 1230 59 29.17 13000 12.9 1460 61 28.56 21300 21.6 1280
2 8 .
1160 41 7320 5.01 1580 39 14100 9.24 1800 40 23900 16 1540
875 31 7320 3.77 1800 29 14900 7.33 2100 30 23900 12.1 1950
3500 108 6630 11.8 990 104 11900 20.6 1160 105 19200 33.6 940
1750 54 32.38 7310 6.5 1340 52 33.52 13500 11.6 1560 52 33.24 22100 19.2 1390
3 2 . 1160 35 7320 4.31 1720 34 14600 8.32 1910 34 23900 13.7 1770
875 27 7320 3.25 1800 26 14900 6.38 2180 26 23900 10.4 2350
3500 96 6890 11 1060 92 12500 19.1 1230 94 19600 30.9 965
1750 48 36.22 7310 5.82 1440 46 38.01 14200 10.8 1610 47 36.88 22800 17.9 1440
3 6 .
1160 32 7320 3.85 1800 30 14900 7.48 2050 31 23900 12.4 1930
875 24 7320 2.91 1800 23 14900 5.64 2440 23 23900 9.36 2400
3500 90 6930 10.4 1090 83 12600 17.4 1300 86 19900 28.7 1040
1750 45 38.61 7320 5.46 1500 41 41.92 14300 9.84 1710 43 40.36 23400 16.8 1500
4 0 . 1160 30 7320 3.61 1800 27 14900 6.78 2190 28 23900 11.3 2080
875 22 7320 2.72 1800 20 14900 5.11 2600 21 23900 8.55 2550
3500 76 7200 9.09 1120 72 13000 15.7 1360 76 20400 26 1160
1750 38 45.76 7320 4.61 1660 36 48.01 14800 8.91 1820 38 45.66 23900 15.1 1620
4 5 .
1160 25 7320 3.05 1800 24 14900 5.92 2390 25 23900 10 2290
875 19 7320 2.3 1800 18 14900 4.46 2900 19 23900 7.56 2750
3500 71 7310 8.65 1160 64 13300 14.2 1410 67 20900 23.5 1210
1750 35 48.86 7320 4.32 1720 32 54.28 14900 7.91 1970 33 51.54 23900 13.4 1810
5 0 . 1160 23 7320 2.86 1800 21 14900 5.24 2580 22 23900 8.89 2500
875 17 7320 2.16 1800 16 14900 3.95 3070 16 23900 6.7 3110
3500 57 7310 6.98 1320 55 13800 12.7 1520 56 21700 20.2 1320
1750 28 60.62 7320 3.48 1800 27 62.94 14900 6.83 2180 28 62.47 23900 11.1 2120
6 3 .
1160 19 7320 2.31 1800 18 14900 4.52 2810 18 23900 7.34 2860
875 14 7320 1.74 1800 13 14900 3.41 3370 14 23900 5.53 3350
3500 48 7310 5.92 1440 46 14400 11.1 1610 48 22700 18.1 1440
1750 24 71.49 7320 2.96 1800 23 75.07 14900 5.73 2440 24 72.86 23900 9.51 2380
7 1 . 1160 16 7320 1.96 1800 15 14900 3.8 3110 15 23900 6.3 3160
875 12 7320 1.48 1800 11 14900 2.86 3370 12 23900 4.75 3520
3500 44 7320 5.41 1500 42 14700 10.4 1710 43 23400 17 1500
1750 22 78.28 7320 2.7 1800 21 82.21 14900 5.24 2580 21 80.03 23900 8.66 2550
8 0 . 1160 14 7320 1.79 1800 14 14900 3.47 3280 14 23900 5.74 3350
875 11 7320 1.35 1800 10 14900 2.62 3370 10 23900 4.33 3520
3500 36 7320 4.43 1720 35 14900 8.76 1820 35 23900 14.2 1770
1750 18 95.93 7320 2.21 1800 17 98.65 14900 4.37 2880 17 98.08 23900 7.07 2930
1 0 0
1160 12 7320 1.46 1800 11 14900 2.9 3370 11 23900 4.68 3520
875 9 7320 1.1 1800 8 14900 2.19 3370 8 23900 3.53 3520
3500 32 7320 3.97 1760 30 14400 7.37 1990 32 23900 13 1810
1750 16 106.9 7320 1.98 1800 15 113.5 14400 3.69 3180 16 107.1 23900 6.48 3110
1 1 2 1160 10 7320 1.31 1800 10 14400 2.44 3370 10 23900 4.29 3520
875 8 7320 0.991 1800 7 14400 1.84 3370 8 23900 3.24 3520
3500 29 5260 2.56 1800 27 12200 5.65 2180 28 23900 11.3 2120
1750 14 119.9 5270 1.28 1800 13 126.1 12200 2.83 3370 14 123.3 23900 5.65 3390
1 2 5 1160 9 5280 0.847 1800 9 12200 1.87 3370 9 23900 3.74 3520
875 7 5280 0.639 1800 6 12200 1.41 3370 7 23900 2.82 3520

68
 SERIES K
TRIPLE REDUCTION RATINGS
SIZES K09 - K12
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
TRIPLE REDUCTION
Input K0931 K1031 K1231
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 435 17400 127 5000 423 34000 239 6610 411 44600 304 10500
1750 217 8.035 21500 77.6 5540 211 8.263 36200 127 7710 205 8.513 44700 152 12300
8 . 0
1160 144 24400 58.1 5890 140 36200 83.9 8550 136 44800 101 13600
875 108 26200 47.1 5800 105 36300 63.3 8700 102 44800 75.9 15200
3500 361 21000 127 4800 351 40900 239 6580 341 53600 304 10500
1750 180 9.681 25900 77.6 5450 175 9.946 43500 127 7620 170 10.26 53800 152 12400
1 0 .
1160 119 29300 58.1 5950 116 43500 83.9 8640 113 53800 101 13800
875 90 31500 47.1 6400 87 43600 63.3 8900 85 53900 75.9 15600
3500 316 20300 107 5100 303 40300 202 6200 296 62000 304 10300
1750 158 11.06 25000 65.5 5660 151 11.54 49600 124 7390 148 11.8 62100 152 12100
1 1 .
1160 104 27900 48.2 6370 100 50700 83.9 8560 98 62200 101 13800
875 79 29100 37.9 6650 75 50700 63.3 8700 74 62200 75.9 15600
3500 282 21400 100 5300 278 41900 193 6350 270 68000 303 10100
1750 141 12.4 26300 61.5 5750 139 12.55 51600 119 7420 135 12.96 68300 152 12000
1 2 .
1160 93 28900 44.6 6590 92 55200 83.9 8550 89 68300 101 13900
875 70 30000 34.9 6900 69 55200 63.3 8960 67 68300 75.9 15700
3500 262 24400 107 5200 251 48400 202 6100 246 74600 304 10200
1750 131 13.33 30100 65.5 5640 125 13.89 59700 124 7200 123 14.21 74700 152 12100
1 4 .
1160 87 33500 48.2 6430 83 60900 83.9 8630 81 74700 101 14200
875 65 34900 37.9 7410 62 61000 63.3 9460 61 74800 75.9 15900
3500 234 25700 100 5300 231 50300 193 6180 224 81800 303 10100
1750 117 14.94 31700 61.5 5780 115 15.11 62000 119 7330 112 15.61 82100 152 12000
1 6 .
1160 77 34700 44.6 6650 76 64200 81.3 8720 74 82100 101 14300
875 58 36100 34.9 7640 57 64200 61.3 9790 56 82100 75.9 15900
3500 195 24900 80.9 5450 188 49500 154 7100 192 78700 249 10000
1750 97 17.93 30000 48.4 6360 94 18.57 60700 94.3 8060 96 18.2 96000 152 11600
1 8 .
1160 64 31800 33.9 7410 62 64200 66 9460 63 96000 101 14000
875 48 33400 26.9 7410 47 64200 49.7 10700 48 96000 75.9 15800
3500 174 26000 75.6 5450 174 51000 147 7200 173 82000 235 10000
1750 87 20.03 30700 44.4 6600 87 20.05 61800 88.9 8270 86 20.17 100999 144 11800
2 0 .
1160 57 32800 31.3 7640 57 64200 61.1 9790 57 105999 101 13900
875 43 33400 24 7640 43 64200 46.1 11200 43 105999 75.9 16000
3500 161 30000 80.9 5600 156 59500 154 7390 159 94600 249 10100
1750 80 21.61 35400 47.5 6450 78 22.35 64200 83 8650 79 21.93 108999 143 12100
2 2 .
1160 53 37300 33.1 7580 51 64200 54.9 10400 52 108999 94.9 14700
875 40 37300 24.9 7580 39 64200 41.4 11200 39 108999 71.6 16200
3500 144 31300 75.6 5750 145 61300 147 7420 144 98600 235 10600
1750 72 24.14 36200 43.4 6720 72 24.13 64200 76.9 8950 72 24.29 108999 129 12700
2 5 .
1160 48 37300 29.6 7640 48 64200 50.9 10700 47 108999 85.7 15300
875 36 37300 22.3 7640 36 64200 38.4 11200 36 108999 64.6 16200
3500 126 29400 61.4 5700 119 58900 116 7330 120 95400 190 10800
1750 63 27.78 33000 34.3 7380 59 29.24 64200 63.3 9640 60 28.99 106999 106 13500
2 8 .
1160 41 33400 23 7640 39 64200 41.9 11200 40 106999 70.5 16200
875 31 33400 17.3 7640 29 64200 31.6 11200 30 106999 53.2 16200
3500 110 30500 55.8 5780 105 61700 108 7800 106 97500 171 10900
1750 55 31.67 33400 30.5 7640 52 33.1 64200 55.9 10200 53 32.83 106999 93.9 14300
3 2 .
1160 36 33400 20.2 7640 35 64200 37 11200 35 106999 62.2 16200
875 27 33400 15.2 7640 26 64200 27.9 11200 26 106999 46.9 16200
3500 104 33700 58.7 6500 99 64200 106 8150 100 108999 180 11000
1750 52 33.47 37300 32.3 7640 49 35.19 64200 52.7 10600 50 34.93 108999 90.1 15000
3 6 .
1160 34 37300 21.4 7640 32 64200 34.9 11200 33 108999 59.7 16200
875 26 37300 16.1 7640 24 64200 26.3 11200 25 108999 45 16200

69
 SERIES K
TRIPLE REDUCTION RATINGS
SIZES K09 - K12
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
TRIPLE REDUCTION
Input K0931 K1031 K1231
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 91 34600 52.7 6600 87 64200 93.4 8270 88 108999 159 11800
1750 45 38.16 37300 28.3 7640 43 39.84 64200 46.6 11200 44 39.55 108999 79.6 15900
4 0 .
1160 30 37300 18.7 7640 29 64200 30.8 11200 29 108999 52.7 16200
875 22 37300 14.1 7640 21 64200 23.2 11200 22 108999 39.7 16200
3500 77 32600 42.2 6800 77 64200 81.8 8650 74 106999 132 12000
1750 38 44.89 33400 21.5 7640 38 45.37 64200 40.8 11200 37 46.81 106999 66.1 16200
4 5 .
1160 25 33400 14.3 7640 25 64200 27 11200 24 106999 43.8 16200
875 19 33400 10.7 7640 19 64200 20.4 11200 18 106999 33 16200
3500 70 33300 38.7 6900 69 64200 73.7 8950 66 106999 117 13000
1750 35 49.87 33400 19.4 7640 34 50.41 64200 36.8 11200 33 52.76 106999 58.6 16200
5 0 .
1160 23 33400 12.8 7640 23 64200 24.3 11200 21 106999 38.9 16200
875 17 33400 9.68 7640 17 64200 18.4 11200 16 106999 29.3 16200
3500 64 37000 39.7 7400 64 64200 68.2 9440 62 108999 112 13500
1750 32 54.09 37300 20 7640 32 54.61 64200 34 11200 31 56.39 108999 56 16200
5 6 .
1160 21 37300 13.2 7640 21 64200 22.5 11200 20 108999 37.1 16200
875 16 37300 9.98 7640 16 64200 17 11200 15 108999 28 16200
3500 58 37300 36.1 7600 57 64200 61.4 9700 55 108999 99.5 14200
1750 29 60.1 37300 18 7640 28 60.68 64200 30.6 11200 27 63.57 108999 49.6 16200
6 3 .
1160 19 37300 11.9 7640 19 64200 20.3 11200 18 108999 32.9 16200
875 14 37300 8.98 7640 14 64200 15.3 11200 13 108999 24.8 16200
3500 49 33400 27.6 7640 48 64200 51.7 10600 46 106999 83.4 15300
1750 24 70.45 33400 13.8 7640 24 71.89 64200 25.8 11200 23 74.62 106999 41.7 16200
7 1 .
1160 16 33400 9.11 7640 16 64200 17.1 11200 15 106999 27.6 16200
875 12 33400 6.87 7640 12 64200 12.9 11200 11 106999 20.8 16200
3500 45 33400 24.9 7640 42 64200 44.9 11200 42 106999 75 16200
1750 22 77.78 33400 12.4 7640 21 82.83 64200 22.4 11200 21 83.1 106999 37.5 16200
8 0 .
1160 14 33400 8.25 7640 14 64200 14.8 11200 13 106999 24.8 16200
875 11 33400 6.22 7640 10 64200 11.2 11200 10 106999 18.7 16200
3500 41 37300 25.6 7640 40 64200 43 11200 38 108999 70.6 16200
1750 20 84.89 37300 12.8 7640 20 86.53 64200 21.5 11200 19 89.89 108999 35.3 16200
9 0 .
1160 13 37300 8.45 7640 13 64200 14.2 11200 12 108999 23.4 16200
875 10 37300 6.37 7640 10 64200 10.7 11200 9 108999 17.6 16200
3500 37 37300 23.2 7640 35 64200 37.4 11200 34 108999 63.5 16200
1750 18 93.71 37300 11.6 7640 17 99.7 64200 18.7 11200 17 100.1 108999 31.7 16200
1 0 0
1160 12 37300 7.65 7640 11 64200 12.4 11200 11 108999 21 16200
875 9 37300 5.77 7640 8 64200 9.32 11200 8 108999 15.8 16200
3500 32 33400 18.2 7640 31 64200 33.3 11200 30 106999 54.6 16200
1750 16 107 33400 9.07 7640 15 112 64200 16.6 11200 15 113.8 106999 27.3 16200
1 1 2
1160 10 33400 6.01 7640 10 64200 11 11200 10 106999 18.1 16200
875 8 33400 4.53 7640 7 64200 8.3 11200 7 106999 13.6 16200
3500 29 33400 16.2 7640 29 64200 31 11200 28 106999 51.3 16200
1750 14 120.3 33400 8.09 7640 14 120.4 64200 15.5 11200 14 121.1 106999 25.6 16200
1 2 5
1160 9 33400 5.36 7640 9 64200 10.3 11200 9 106999 17 16200
875 7 33400 4.04 7640 7 64200 7.74 11200 7 106999 12.8 16200
3500 27 37300 16.9 7640 25 64200 27.7 11200 25 108999 46.3 16200
1750 13 128.9 37300 8.42 7640 12 134.8 64200 13.8 11200 12 137.1 108999 23.1 16200
1 4 0
1160 8 37300 5.58 7640 8 64200 9.16 11200 8 108999 15.3 16200
875 6 37300 4.21 7640 6 64200 6.91 11200 6 108999 11.5 16200
3500 24 37300 15 7640 24 64200 25.8 11200 23 108999 43.5 16200
1750 12 145 37300 7.51 7640 12 144.9 64200 12.9 11200 11 145.9 108999 21.7 16200
1 6 0
1160 8 37300 4.97 7640 8 64200 8.54 11200 7 108999 14.4 16200
875 6 37300 3.75 7640 6 64200 6.44 11200 5 108999 10.8 16200

70
 SERIES K
QUINTUPLE REDUCTION RATINGS
SIZES K03 - K05
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
QUINTUPLE REDUCTION
Input K0352 K0452 K0552
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 27.39 1991 0.911 1350 26.05 3894 1.694 1350 29.56 5841 2.88 1688
1750 13.69 128 1991 0.455 1350 13.02 134 3894 0.847 1350 14.78 118 5841 1.44 1688
1 2 5
1160 9.08 1991 0.302 1350 8.63 3894 0.561 1350 9.80 5841 0.96 1688
875 6.85 1991 0.228 1350 6.51 3894 0.423 1350 7.39 5841 0.72 1688
3500 24.08 1991 0.801 1350 23.65 3894 1.538 1350 24.51 5841 2.39 1688
1750 12.04 145 1991 0.400 1350 11.83 148 3894 0.769 1350 12.26 143 5841 1.20 1688
1 4 0 1160 7.98 1991 0.265 1350 7.84 3894 0.510 1350 8.12 5841 0.79 1688
875 6.02 1991 0.200 1350 5.91 3894 0.385 1350 6.13 5841 0.60 1688
3500 21.26 1991 0.707 1350 20.56 3894 1.337 1350 22.24 5841 2.17 1688
1750 10.63 165 1991 0.353 1350 10.28 170 3894 0.669 1350 11.12 157 5841 1.09 1688
1 6 0 1160 7.04 1991 0.234 1350 6.82 3894 0.443 1350 7.37 5841 0.72 1688
875 5.31 1991 0.177 1350 5.14 3894 0.334 1350 5.56 5841 0.54 1688
3500 16.62 1991 0.553 1350 17.51 3894 1.139 1350 16.84 5841 1.64 1688
1750 8.31 211 1991 0.276 1350 8.75 200 3894 0.569 1350 8.42 208 5841 0.82 1688
2 0 0 5.51 1991 0.183 1350 5.80 3894 0.377 1350 5.58 5841 0.54 1688
1160
875 4.16 1991 0.138 1350 4.38 3894 0.285 1350 4.21 5841 0.41 1688
3500 15.42 1991 0.513 1350 13.59 3894 0.884 1350 13.26 5841 1.29 1688
1750 7.71 227 1991 0.256 1350 6.79 258 3894 0.442 1350 6.63 264 5841 0.65 1688
2 5 0
1160 5.11 1991 0.170 1350 4.50 3894 0.293 1350 4.39 5841 0.43 1688
875 3.86 1991 0.128 1350 3.40 3894 0.221 1350 3.32 5841 0.32 1688
3500 12.22 1991 0.406 1350 12.31 3894 0.801 1350 11.67 5841 1.14 1688
1750 6.11 287 1991 0.203 1350 6.15 284 3894 0.400 1350 5.84 300 5841 0.57 1688
2 8 0 1160 4.05 1991 0.135 1350 4.08 3894 0.265 1350 3.87 5841 0.38 1688
875 3.05 1991 0.102 1350 3.08 3894 0.200 1350 2.92 5841 0.28 1688
3500 10.78 1991 0.358 1350 10.86 3894 0.706 1350 11.06 5841 1.08 1688
1750 5.39 325 1991 0.179 1350 5.43 322 3894 0.353 1350 5.53 316 5841 0.54 1688
3 2 0 1160 3.57 1991 0.119 1350 3.60 3894 0.234 1350 3.67 5841 0.36 1688
875 2.69 1991 0.090 1350 2.71 3894 0.177 1350 2.77 5841 0.27 1688
3500 9.43 1991 0.314 1350 9.86 3894 0.641 1350 9.97 5841 0.97 1688
1750 4.71 371 1991 0.157 1350 4.93 355 3894 0.321 1350 4.99 351 5841 0.49 1688
3 6 0 1160 3.13 1991 0.104 1350 3.27 3894 0.212 1350 3.31 5841 0.32 1688
875 2.36 1991 0.078 1350 2.46 3894 0.160 1350 2.49 5841 0.24 1688
3500 8.48 1991 0.282 1350 8.60 3894 0.559 1350 8.78 5841 0.86 1688
1750 4.24 413 1991 0.141 1350 4.30 407 3894 0.280 1350 4.39 399 5841 0.43 1688
4 0 0
1160 2.81 1991 0.093 1350 2.85 3894 0.185 1350 2.91 5841 0.28 1688
875 2.12 1991 0.070 1350 2.15 3894 0.140 1350 2.19 5841 0.21 1688
3500 7.69 1991 0.256 1350 7.81 3894 0.508 1350 7.73 5841 0.75 1688
1750 3.84 455 1991 0.128 1350 3.90 448 3894 0.254 1350 3.86 453 5841 0.38 1688
4 5 0 1160 2.55 1991 0.085 1350 2.59 3894 0.168 1350 2.56 5841 0.25 1688
875 1.92 1991 0.064 1350 1.95 3894 0.127 1350 1.93 5841 0.19 1688
3500 6.78 1991 0.226 1350 6.89 3894 0.448 1350 7.02 5841 0.68 1688
1750 3.39 516 1991 0.113 1350 3.44 508 3894 0.224 1350 3.51 499 5841 0.34 1688
5 0 0 1160 2.25 1991 0.075 1350 2.28 3894 0.148 1350 2.33 5841 0.23 1688
875 1.70 1991 0.056 1350 1.72 3894 0.112 1350 1.75 5841 0.17 1688
3500 6.16 1991 0.205 1350 6.03 3894 0.392 1350 6.10 5841 0.60 1688
1750 3.08 568 1991 0.102 1350 3.01 581 3894 0.196 1350 3.05 574 5841 0.30 1688
5 6 0
1160 2.04 1991 0.068 1350 2.00 3894 0.130 1350 2.02 5841 0.20 1688
875 1.54 1991 0.051 1350 1.51 3894 0.098 1350 1.53 5841 0.15 1688
3500 5.39 1991 0.179 1350 5.42 3894 0.352 1350 5.61 5841 0.55 1688
1750 2.70 649 1991 0.090 1350 2.71 646 3894 0.176 1350 2.81 624 5841 0.27 1688
6 3 0
1160 1.79 1991 0.059 1350 1.80 3894 0.117 1350 1.86 5841 0.18 1688
875 1.35 1991 0.045 1350 1.35 3894 0.088 1350 1.40 5841 0.137 1688
3500 4.97 1991 0.165 1350 4.91 3894 0.320 1350 4.82 5841 0.47 1688
1750 2.49 704 1991 0.083 1350 2.46 712 3894 0.160 1350 2.41 725 5841 0.24 1688
7 0 0 1160 1.65 1991 0.055 1350 1.63 3894 0.106 1350 1.60 5841 0.156 1688
875 1.24 1991 0.041 1350 1.23 3894 0.080 1350 1.21 5841 0.118 1688
3500 4.38 1991 0.146 1350 4.33 3894 0.282 1350 4.31 5841 0.42 1688
1750 2.19 798 1991 0.073 1350 2.17 808 3894 0.141 1350 2.16 812 5841 0.21 1688
8 0 0 1160 1.45 1991 0.048 1350 1.44 3894 0.093 1350 1.43 5841 0.139 1688
875 1.096 1991 0.036 1350 1.083 3894 0.070 1350 1.078 5841 0.105 1688
3500 3.84 1991 0.128 1350 3.93 3894 0.256 1350 3.90 5841 0.38 1688
1750 1.92 912 1991 0.064 1350 1.97 891 3894 0.128 1350 1.95 899 5841 0.19 1688
9 0 0 1160 1.27 1991 0.042 1350 1.30 3894 0.085 1350 1.29 5841 0.126 1688
875 0.959 1991 0.032 1350 0.983 3894 0.064 1350 0.974 5841 0.095 1688
3500 3.45 1991 0.115 1350 3.50 3894 0.228 1350 3.35 5841 0.33 1688
1750 1.72 1015 1991 0.057 1350 1.75 1000 3894 0.114 1350 1.67 1045 5841 0.16 1688
1 0 c
1160 1.143 1991 0.038 1350 1.160 3894 0.075 1350 1.110 5841 0.108 1688
875 0.862 1991 0.029 1350 0.875 3894 0.057 1350 0.837 5841 0.082 1688

71
 SERIES K
QUINTUPLE REDUCTION RATINGS
SIZES K03 - K05
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
QUINTUPLE REDUCTION
Input K0352 K0452 K0552
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 3.13 1991 0.104 1350 3.18 3894 0.207 1350 2.99 5841 0.29 1688
1750 1.56 1119 1991 0.052 1350 1.59 1102 3894 0.103 1350 1.50 1169 5841 0.146 1688
1 1 c
1160 1.037 1991 0.034 1350 1.053 3894 0.068 1350 0.992 5841 0.097 1688
875 0.782 1991 0.026 1350 0.794 3894 0.052 1350 0.748 5841 0.073 1688
3500 2.96 1991 0.098 1350 2.76 3894 0.180 1350 2.84 5841 0.28 1688
1750 1.48 1183 1991 0.049 1350 1.38 1267 3894 0.090 1350 1.42 1231 5841 0.139 1688
1 2 c 1160 0.981 1991 0.033 1350 0.915 3894 0.060 1350 0.942 5841 0.092 1688
875 0.740 1991 0.025 1350 0.691 3894 0.045 1350 0.711 5841 0.069 1688
3500 2.46 1991 0.082 1350 2.45 3894 0.160 1350 2.37 5841 0.23 1688
1750 1.23 1423 1991 0.041 1350 1.23 1427 3894 0.080 1350 1.18 1477 5841 0.116 1688
1 4 c 1160 0.815 1991 0.027 1350 0.813 3894 0.053 1350 0.785 5841 0.077 1688
875 0.615 1991 0.020 1350 0.613 3894 0.040 1350 0.592 5841 0.058 1688
3500 2.21 1991 0.074 1350 2.18 3894 0.142 1350 2.22 5841 0.22 1688
1750 1.106 1583 1991 0.037 1350 1.090 1606 3894 0.071 1350 1.110 1577 5841 0.108 1688
1 6 c 0.733 1991 0.024 1350 0.722 3894 0.047 1350 0.736 5841 0.072 1688
1160
875 0.553 1991 0.018 1350 0.545 3894 0.035 1350 0.555 5841 0.054 1688
3500 1.94 1991 0.065 1350 1.96 3894 0.128 1350 1.97 5841 0.19 1688
1750 0.972 1800 1991 0.032 1350 0.981 1784 3894 0.064 1350 0.985 1777 5841 0.096 1688
1 8 c
1160 0.644 1991 0.021 1350 0.650 3894 0.042 1350 0.653 5841 0.064 1688
875 0.486 1991 0.016 1350 0.490 3894 0.032 1350 0.492 5841 0.048 1688
3500 1.75 1991 0.058 1350 1.56 3894 0.115 1350 1.79 5841 0.17 1688
1750 0.875 2000 1991 0.029 1350 0.778 2250 3894 0.058 1350 0.894 1957 5841 0.087 1688
2 0 c 1160 0.580 1991 0.019 1350 0.516 3894 0.038 1350 0.593 5841 0.058 1688
875 0.437 1991 0.015 1350 0.389 3894 0.029 1350 0.447 5841 0.044 1688
3500 1.56 1991 0.052 1350 1.55 3894 0.100 1350 1.59 5841 0.155 1688
1750 0.778 2250 1991 0.026 1350 0.773 2265 3894 0.050 1350 0.794 2205 5841 0.077 1688
2 2 c 1160 0.516 1991 0.017 1350 0.512 3894 0.033 1350 0.526 5841 0.051 1688
875 0.389 1991 0.013 1350 0.386 3894 0.025 1350 0.397 5841 0.039 1688
3500 1.36 1991 0.045 1350 1.42 3894 0.092 1350 1.37 5841 0.133 1688
1750 0.679 2579 1991 0.023 1350 0.711 2463 3894 0.046 1350 0.683 2563 5841 0.067 1688
2 5 c 1160 0.450 1991 0.015 1350 0.471 3894 0.031 1350 0.453 5841 0.044 1688
875 0.339 1991 0.011 1350 0.355 3894 0.023 1350 0.341 5841 0.033 1688
3500 1.30 1991 0.043 1350 1.25 3894 0.081 1350 1.23 5841 0.120 1688
1750 0.648 2699 1991 0.022 1350 0.625 2799 3894 0.041 1350 0.615 2847 5841 0.060 1688
2 8 c
1160 0.430 1991 0.014 1350 0.414 3894 0.027 1350 0.407 5841 0.040 1688
875 0.324 1991 0.011 1350 0.313 3894 0.020 1350 0.307 5841 0.030 1688
3500 1.131 1991 0.038 1350 1.042 3894 0.068 1350 1.057 5841 0.103 1688
1750 0.566 3094 1991 0.019 1350 0.521 3360 3894 0.034 1350 0.529 3310 5841 0.052 1688
3 2 c 1160 0.375 1991 0.012 1350 0.345 3894 0.022 1350 0.350 5841 0.034 1688
875 0.283 1991 0.009 1350 0.260 3894 0.017 1350 0.264 5841 0.026 1688
3500 0.995 1991 0.033 1350 0.987 3894 0.064 1350 0.932 5841 0.091 1688
1750 0.498 3516 1991 0.017 1350 0.493 3548 3894 0.032 1350 0.466 3757 5841 0.045 1688
3 6 c 1160 0.330 1991 0.011 1350 0.327 3894 0.021 1350 0.309 5841 0.030 1688
875 0.249 1991 0.008 1350 0.247 3894 0.016 1350 0.233 5841 0.023 1688
3500 0.873 1991 0.029 1350 0.876 3894 0.057 1350 0.863 5841 0.084 1688
1750 0.437 4007 1991 0.015 1350 0.438 3998 3894 0.028 1350 0.431 4056 5841 0.042 1688
4 0 c
1160 0.289 1991 0.010 1350 0.290 3894 0.019 1350 0.286 5841 0.028 1688
875 0.218 1991 0.007 1350 0.219 3894 0.014 1350 0.216 5841 0.021 1688
3500 0.768 1991 0.026 1350 0.770 3894 0.050 1350 0.760 5841 0.074 1688
1750 0.384 4554 1991 0.013 1350 0.385 4543 3894 0.025 1350 0.380 4604 5841 0.037 1688
4 5 c
1160 0.255 1991 0.008 1350 0.255 3894 0.017 1350 0.252 5841 0.025 1688
875 0.192 1991 0.006 1350 0.193 3894 0.013 1350 0.190 5841 0.019 1688
3500 0.725 1655 0.020 1350 0.753 3894 0.049 1350 0.682 5841 0.067 1688
1750 0.363 4826 1655 0.010 1350 0.377 4647 3894 0.024 1350 0.341 5131 5841 0.033 1688
5 0 c 1160 0.240 1655 0.007 1350 0.250 3894 0.016 1350 0.226 5841 0.022 1688
875 0.181 1655 0.005 1350 0.188 3894 0.012 1350 0.171 5841 0.017 1688
3500 0.638 1655 0.018 1350 0.663 3894 0.043 1350 0.669 5841 0.065 1688
1750 0.319 5485 1655 0.009 1350 0.331 5281 3894 0.022 1350 0.334 5234 5841 0.033 1688
5 6 c 1160 0.212 1655 0.006 1350 0.220 3894 0.014 1350 0.222 5841 0.022 1688
875 0.160 1655 0.004 1350 0.166 3894 0.011 1350 0.167 5841 0.016 1688
3500 0.557 1416 0.013 1350 0.584 3894 0.038 1350 0.600 5841 0.059 1688
1750 0.278 6286 1416 0.007 1350 0.292 5994 3894 0.019 1350 0.300 5833 5841 0.029 1688
6 3 c 1160 0.185 1416 0.004 1350 0.194 3894 0.013 1350 0.199 5841 0.019 1688
875 0.139 1416 0.003 1350 0.146 3894 0.009 1350 0.150 5841 0.015 1688
3500 0.490 1398 0.011 1350 0.514 3894 0.033 1350 0.535 5354 0.048 1688
1750 0.245 7144 1398 0.006 1350 0.257 6815 3894 0.017 1350 0.267 6542 5354 0.024 1688
7 1 c
1160 0.162 1398 0.004 1350 0.170 3894 0.011 1350 0.177 5354 0.016 1688
875 0.122 1398 0.003 1350 0.128 3894 0.008 1350 0.134 5354 0.012 1688

72
 SERIES K
QUINTUPLE REDUCTION RATINGS
SIZES K06 - K08
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
QUINTUPLE REDUCTION
Input K0652 K0752 K0852
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 30.12 7301 3.67 1800 29.10 14160 6.88 3375 26.48 23984 10.61 3533
1750 15.06 116 7301 1.84 1800 14.55 120 14160 3.44 3375 13.24 132 23984 5.30 3533
1 2 5
1160 9.98 7301 1.22 1800 9.64 14160 2.28 3375 8.77 23984 3.51 3533
875 7.53 7301 0.92 1800 7.27 14160 1.72 3375 6.62 23984 2.65 3533
3500 24.98 7301 3.05 1800 26.22 14160 6.20 3375 24.19 23984 9.69 3533
1750 12.49 140 7301 1.52 1800 13.11 133 14160 3.10 3375 12.10 145 23984 4.85 3533
1 4 0 1160 8.28 7301 1.01 1800 8.69 14160 2.06 3375 8.02 23984 3.21 3533
875 6.24 7301 0.76 1800 6.56 14160 1.55 3375 6.05 23984 2.42 3533
3500 22.67 7301 2.76 1800 23.80 14160 5.63 3375 21.38 23984 8.57 3533
1750 11.33 154 7301 1.38 1800 11.90 147 14160 2.81 3375 10.69 164 23984 4.28 3533
1 6 0 1160 7.51 7301 0.92 1800 7.89 14160 1.87 3375 7.09 23984 2.84 3533
875 5.67 7301 0.69 1800 5.95 14160 1.41 3375 5.35 23984 2.14 3533
3500 17.16 7301 2.09 1800 16.58 14160 3.92 3375 17.21 21417 6.16 3533
1750 8.58 204 7301 1.05 1800 8.29 211 14160 1.96 3375 8.60 203 21417 3.08 3533
2 0 0 5.69 7301 0.69 1800 5.49 14160 1.30 3375 5.70 21417 2.04 3533
1160
875 4.29 7301 0.52 1800 4.14 14160 0.98 3375 4.30 21417 1.54 3533
3500 13.51 7301 1.65 1800 15.00 14160 3.55 3375 13.68 23984 5.48 3533
1750 6.76 259 7301 0.82 1800 7.50 233 14160 1.77 3375 6.84 256 23984 2.74 3533
2 5 0
1160 4.48 7301 0.55 1800 4.97 14160 1.18 3375 4.53 23984 1.82 3533
875 3.38 7301 0.41 1800 3.75 14160 0.89 3375 3.42 23984 1.37 3533
3500 11.89 7301 1.45 1800 13.20 14160 3.12 3375 11.79 23984 4.72 3533
1750 5.95 294 7301 0.73 1800 6.60 265 14160 1.56 3375 5.89 297 23984 2.36 3533
2 8 0 1160 3.94 7301 0.48 1800 4.38 14160 1.03 3375 3.91 23984 1.56 3533
875 2.97 7301 0.36 1800 3.30 14160 0.78 3375 2.95 23984 1.18 3533
3500 11.27 7301 1.37 1800 11.49 14160 2.72 3375 10.77 23984 4.31 3533
1750 5.64 310 7301 0.69 1800 5.74 305 14160 1.36 3375 5.39 325 23984 2.16 3533
3 2 0 1160 3.74 7301 0.46 1800 3.81 14160 0.90 3375 3.57 23984 1.43 3533
875 2.82 7301 0.34 1800 2.87 14160 0.68 3375 2.69 23984 1.08 3533
3500 10.16 7301 1.24 1800 9.36 14160 2.21 3375 9.50 23984 3.81 3533
1750 5.08 344 7301 0.62 1800 4.68 374 14160 1.11 3375 4.75 368 23984 1.90 3533
3 6 0 1160 3.37 7301 0.41 1800 3.10 14160 0.73 3375 3.15 23984 1.26 3533
875 2.54 7301 0.31 1800 2.34 14160 0.55 3375 2.38 23984 0.95 3533
3500 8.95 7301 1.09 1800 8.44 14603 2.06 3375 8.72 23984 3.49 3533
1750 4.47 391 7301 0.55 1800 4.22 415 14603 1.03 3375 4.36 401 23984 1.75 3533
4 0 0
1160 2.97 7301 0.36 1800 2.80 14603 0.68 3375 2.89 23984 1.16 3533
875 2.24 7301 0.27 1800 2.11 14603 0.51 3375 2.18 23984 0.87 3533
3500 7.87 7301 0.96 1800 7.51 14603 1.83 3375 7.57 23984 3.03 3533
1750 3.94 445 7301 0.48 1800 3.76 466 14603 0.92 3375 3.79 462 23984 1.52 3533
4 5 0 1160 2.61 7301 0.32 1800 2.49 14603 0.61 3375 2.51 23984 1.01 3533
875 1.93 7301 0.24 1800 1.88 14603 0.46 3375 1.89 23984 0.76 3533
3500 7.15 7301 0.87 1800 6.82 14603 1.66 3375 6.92 23984 2.77 3533
1750 3.58 489 7301 0.44 1800 3.41 513 14603 0.83 3375 3.46 506 23984 1.39 3533
5 0 0 1160 2.37 7301 0.29 1800 2.26 14603 0.55 3375 2.29 23984 0.92 3533
875 1.79 7301 0.22 1800 1.71 14603 0.42 3375 1.73 23984 0.69 3533
3500 6.22 7301 0.76 1800 5.93 14603 1.45 3375 6.51 23984 2.61 3533
1750 3.11 563 7301 0.38 1800 2.97 590 14603 0.72 3375 3.25 538 23984 1.30 3533
5 6 0
1160 2.06 7301 0.25 1800 1.97 14603 0.48 3375 2.16 23984 0.86 3533
875 1.55 7301 0.19 1800 1.48 14603 0.36 3375 1.63 23984 0.65 3533
3500 5.72 7301 0.70 1800 5.46 14603 1.33 3375 5.46 23984 2.19 3533
1750 2.86 612 7301 0.35 1800 2.73 641 14603 0.67 3375 2.73 641 23984 1.09 3533
6 3 0
1160 1.90 7301 0.23 1800 1.81 14603 0.44 3375 1.81 23984 0.72 3533
875 1.43 7301 0.17 1800 1.36 14603 0.33 3375 1.36 23984 0.55 3533
3500 4.92 7301 0.60 1800 4.75 14603 1.16 3375 4.61 23984 1.85 3533
1750 2.46 712 7301 0.30 1800 2.37 737 14603 0.58 3375 2.30 760 23984 0.92 3533
7 0 0 1160 1.63 7301 0.20 1800 1.57 14603 0.38 3375 1.53 23984 0.61 3533
875 1.23 7301 0.150 1800 1.19 14603 0.29 3375 1.15 23984 0.46 3533
3500 4.39 7301 0.54 1800 4.19 14603 1.02 3375 4.31 23984 1.73 3533
1750 2.20 797 7301 0.27 1800 2.09 836 14603 0.51 3375 2.16 811 23984 0.86 3533
8 0 0 1160 1.46 7301 0.18 1800 1.39 14603 0.34 3375 1.43 23984 0.57 3533
875 1.098 7301 0.134 1800 1.047 14603 0.26 3375 1.079 23984 0.43 3533
3500 3.97 7301 0.48 1800 3.79 14603 0.92 3375 3.94 23984 1.58 3533
1750 1.98 882 7301 0.24 1800 1.89 924 14603 0.46 3375 1.97 888 23984 0.79 3533
9 0 0 1160 1.32 7301 0.160 1800 1.26 14603 0.31 3375 1.31 23984 0.52 3533
875 0.992 7301 0.121 1800 0.947 14603 0.23 3375 0.986 23984 0.39 3533
3500 3.41 7301 0.42 1800 3.30 14603 0.80 3375 3.48 23984 1.39 3533
1750 1.71 1026 7301 0.21 1800 1.65 1062 14603 0.40 3375 1.74 1007 23984 0.70 3533
1 0 c
1160 1.131 7301 0.138 1800 1.093 14603 0.27 3375 1.152 23984 0.46 3533
875 0.853 7301 0.104 1800 0.824 14603 0.20 3375 0.869 23984 0.35 3533

73
 SERIES K
QUINTUPLE REDUCTION RATINGS
SIZES K06 - K08
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
QUINTUPLE REDUCTION
Input K0652 K0752 K0852
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 3.05 7301 0.37 1800 2.91 14603 0.71 3375 3.18 23984 1.27 3533
1750 1.53 1147 7301 0.19 1800 1.45 1204 14603 0.35 3375 1.59 1102 23984 0.64 3533
1 1 c
1160 1.011 7301 0.123 1800 0.963 14603 0.23 3375 1.053 23984 0.42 3533
875 0.763 7301 0.093 1800 0.727 14603 0.18 3375 0.794 23984 0.32 3533
3500 2.90 7301 0.35 1800 2.76 14603 0.67 3375 2.81 23984 1.12 3533
1750 1.45 1208 7301 0.18 1800 1.38 1267 14603 0.34 3375 1.40 1246 23984 0.56 3533
1 2 c 1160 0.960 7301 0.117 1800 0.915 14603 0.22 3375 0.931 23984 0.37 3533
875 0.724 7301 0.088 1800 0.690 14603 0.17 3375 0.702 23984 0.28 3533
3500 2.41 7301 0.29 1800 2.30 14603 0.56 3375 2.38 23984 0.95 3533
1750 1.21 1449 7301 0.147 1800 1.15 1521 14603 0.28 3375 1.19 1470 23984 0.48 3533
1 4 c 1160 0.800 7301 0.098 1800 0.763 14603 0.19 3375 0.789 23984 0.32 3533
875 0.604 7301 0.074 1800 0.575 14603 0.140 3375 0.595 23984 0.24 3533
3500 2.26 7301 0.28 1800 2.04 14603 0.50 3375 2.11 23984 0.85 3533
1750 1.131 1548 7301 0.138 1800 1.018 1720 14603 0.25 3375 1.055 1659 23984 0.42 3533
1 6 c 0.750 7301 0.091 1800 0.675 14603 0.16 3375 0.699 23984 0.28 3533
1160
875 0.565 7301 0.069 1800 0.509 14603 0.124 3375 0.527 23984 0.21 3533
3500 2.01 7301 0.24 1800 1.81 14603 0.44 3375 1.93 23984 0.77 3533
1750 1.004 1744 7301 0.122 1800 0.903 1938 14603 0.22 3375 0.963 1817 23984 0.39 3533
1 8 c
1160 0.665 7301 0.081 1800 0.599 14603 0.146 3375 0.639 23984 0.26 3533
875 0.502 7301 0.061 1800 0.452 14603 0.110 3375 0.482 23984 0.19 3533
3500 1.82 7301 0.22 1800 1.76 14603 0.43 3375 1.74 23984 0.70 3533
1750 0.911 1920 7301 0.111 1800 0.878 1994 14603 0.21 3375 0.870 2011 23984 0.35 3533
2 0 c 1160 0.604 7301 0.074 1800 0.582 14603 0.142 3375 0.577 23984 0.23 3533
875 0.456 7301 0.056 1800 0.439 14603 0.107 3375 0.435 23984 0.17 3533
3500 1.62 7301 0.20 1800 1.56 14603 0.38 3375 1.59 23984 0.64 3533
1750 0.809 2164 7301 0.099 1800 0.779 2246 14603 0.19 3375 0.795 2202 23984 0.32 3533
2 2 c 1160 0.536 7301 0.065 1800 0.516 14603 0.126 3375 0.527 23984 0.21 3533
875 0.404 7301 0.049 1800 0.390 14603 0.095 3375 0.397 23984 0.159 3533
3500 1.39 7301 0.17 1800 1.34 14603 0.33 3375 1.30 23984 0.52 3533
1750 0.696 2515 7301 0.085 1800 0.670 2611 14603 0.16 3375 0.648 2699 23984 0.26 3533
2 5 c 1160 0.461 7301 0.056 1800 0.444 14603 0.108 3375 0.430 23984 0.17 3533
875 0.348 7301 0.042 1800 0.335 14603 0.082 3375 0.324 23984 0.130 3533
3500 1.25 7301 0.153 1800 1.19 14603 0.29 3375 1.24 23984 0.50 3533
1750 0.626 2794 7301 0.076 1800 0.596 2934 14603 0.145 3375 0.620 2821 23984 0.25 3533
2 8 c
1160 0.415 7301 0.051 1800 0.395 14603 0.096 3375 0.411 23984 0.16 3533
875 0.313 7301 0.038 1800 0.298 14603 0.073 3375 0.310 23984 0.124 3533
3500 1.078 7301 0.131 1800 1.026 14603 0.25 3375 1.112 23984 0.45 3533
1750 0.539 3248 7301 0.066 1800 0.513 3411 14603 0.125 3375 0.556 3147 23984 0.22 3533
3 2 c 1160 0.357 7301 0.044 1800 0.340 14603 0.083 3375 0.369 23984 0.148 3533
875 0.269 7301 0.033 1800 0.257 14603 0.063 3375 0.278 23984 0.111 3533
3500 0.949 7301 0.116 1800 0.904 14603 0.22 3375 0.908 23984 0.36 3533
1750 0.475 3686 7301 0.058 1800 0.452 3871 14603 0.110 3375 0.454 3853 23984 0.18 3533
3 6 c 1160 0.315 7301 0.038 1800 0.300 14603 0.073 3375 0.301 23984 0.121 3533
875 0.237 7301 0.029 1800 0.226 14603 0.055 3375 0.227 23984 0.091 3533
3500 0.879 7301 0.107 1800 0.855 14603 0.21 3375 0.826 23984 0.33 3533
1750 0.440 3981 7301 0.054 1800 0.428 4093 14603 0.104 3375 0.413 4237 23984 0.17 3533
4 0 c
1160 0.291 7301 0.036 1800 0.283 14603 0.069 3375 0.274 23984 0.110 3533
875 0.220 7301 0.027 1800 0.214 14603 0.052 3375 0.207 23984 0.083 3533
3500 0.775 7301 0.094 1800 0.753 14603 0.18 3375 0.741 23984 0.30 3533
1750 0.387 4518 7301 0.047 1800 0.377 4646 14603 0.092 3375 0.371 4722 23984 0.148 3533
4 5 c
1160 0.257 7301 0.031 1800 0.250 14603 0.061 3375 0.246 23984 0.098 3533
875 0.194 7301 0.024 1800 0.188 14603 0.046 3375 0.185 23984 0.074 3533
3500 0.695 7301 0.085 1800 0.663 14603 0.16 3375 0.679 23984 0.27 3533
1750 0.348 5036 7301 0.042 1800 0.331 5281 14603 0.081 3375 0.339 5157 23984 0.136 3533
5 0 c 1160 0.230 7301 0.028 1800 0.220 14603 0.054 3375 0.225 23984 0.090 3533
875 0.174 7301 0.021 1800 0.166 14603 0.040 3375 0.170 23984 0.068 3533
3500 0.681 7301 0.083 1800 0.655 14603 0.16 3375 0.661 23984 0.26 3533
1750 0.341 5136 7301 0.042 1800 0.327 5345 14603 0.080 3375 0.330 5296 23984 0.132 3533
5 6 c 1160 0.226 7301 0.028 1800 0.217 14603 0.053 3375 0.219 23984 0.088 3533
875 0.170 7301 0.021 1800 0.164 14603 0.040 3375 0.165 23984 0.066 3533
3500 0.611 7301 0.075 1800 0.576 14603 0.140 3375 0.605 23984 0.24 3533
1750 0.306 5725 7301 0.037 1800 0.288 6076 14603 0.070 3375 0.303 5783 23984 0.121 3533
6 3 c 1160 0.203 7301 0.025 1800 0.191 14603 0.047 3375 0.201 23984 0.080 3533
875 0.153 7301 0.019 1800 0.144 14603 0.035 3375 0.151 23984 0.061 3533
3500 0.545 5354 0.049 1800 0.518 12036 0.104 3375 0.526 23984 0.21 3533
1750 0.273 6420 5354 0.024 1800 0.259 6752 12036 0.052 3375 0.263 6660 23984 0.105 3533
7 1 c
1160 0.181 5354 0.016 1800 0.172 12036 0.035 3375 0.174 23984 0.070 3533
875 0.136 5354 0.012 1800 0.130 12036 0.026 3375 0.131 23984 0.053 3533

74
 SERIES K
QUINTUPLE REDUCTION RATINGS
SIZES K09 - K12
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
QUINTUPLE REDUCTION
Input K0951 K1051 K1251
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500
1750
1 2 5
1160
875
3500
1750
1 4 0 1160
875
3500 21.75 36374 13.21 7650 20.98 64163 22.48 9698 20.33 107085 36.36 13793
1750 10.87 161 36374 6.61 7650 10.49 167 64163 11.24 9698 10.17 172 107085 18.18 13793
1 6 0 1160 7.21 36374 4.38 7650 6.95 64163 7.45 9698 6.74 107085 12.05 13793
875 5.44 36374 3.30 7650 5.24 64163 5.62 9698 5.08 107085 9.09 13793
3500 15.47 36374 9.40 7650 15.47 64163 16.23 9698 13.02 107085 23.29 13793
1750 7.73 226 36374 4.70 7650 7.73 226 64163 8.11 9698 6.51 269 107085 11.64 13793
2 0 0 5.13 36374 3.11 7650 5.13 64163 5.38 9698 4.32 107085 7.72 13793
1160
875 3.87 36374 2.35 7650 3.87 64163 4.06 9698 3.26 107085 5.82 13793
3500 13.80 36374 8.38 7650 13.48 64163 14.45 9698 14.68 107085 26.25 13793
1750 6.90 254 36374 4.19 7650 6.74 260 64163 7.22 9698 7.34 238 107085 13.13 13793
2 5 0
1160 4.57 36374 2.78 7650 4.47 64163 4.79 9698 4.86 107085 8.70 13793
875 3.45 36374 2.10 7650 3.37 64163 3.61 9698 3.67 107085 6.56 13793
3500 12.42 36374 7.55 7650 12.26 64163 13.14 9698 11.59 107085 20.73 13793
1750 6.21 282 36374 3.77 7650 6.13 285 64163 6.57 9698 5.80 302 107085 10.37 13793
2 8 0 1160 4.12 36374 2.50 7650 4.06 64163 4.35 9698 3.84 107085 6.87 13793
875 3.11 36374 1.89 7650 3.07 64163 3.28 9698 2.90 107085 5.18 13793
3500 11.07 36374 6.72 7650 11.03 64163 11.82 9698 10.54 107085 18.86 13793
1750 5.53 316 36374 3.36 7650 5.52 317 64163 5.91 9698 5.27 332 107085 9.43 13793
3 2 0 1160 3.67 36374 2.23 7650 3.66 64163 3.92 9698 3.49 107085 6.25 13793
875 2.77 36374 1.68 7650 2.76 64163 2.96 9698 2.64 107085 4.71 13793
3500 9.68 36374 5.88 7650 9.39 64163 10.06 9698 9.10 107085 16.27 13793
1750 4.84 361 36374 2.94 7650 4.69 373 64163 5.03 9698 4.55 385 107085 8.14 13793
3 6 0 1160 3.21 36374 1.95 7650 3.11 64163 3.33 9698 3.02 107085 5.39 13793
875 2.42 36374 1.47 7650 2.35 64163 2.51 9698 2.27 107085 4.07 13793
3500 8.71 36374 5.29 7650 8.45 64163 9.05 9698 8.00 107085 14.31 13793
1750 4.36 402 36374 2.65 7650 4.22 414 64163 4.53 9698 4.00 437 107085 7.16 13793
4 0 0
1160 2.89 36374 1.75 7650 2.80 64163 3.00 9698 2.65 107085 4.74 13793
875 2.18 36374 1.32 7650 2.11 64163 2.26 9698 2.00 107085 3.58 13793
3500 7.69 36374 4.67 7650 7.43 64163 7.96 9698 7.10 107085 12.70 13793
1750 3.84 455 36374 2.34 7650 3.72 471 64163 3.98 9698 3.55 493 107085 6.35 13793
4 5 0 1160 2.55 36374 1.55 7650 2.46 64163 2.64 9698 2.35 107085 4.21 13793
875 1.92 36374 1.17 7650 1.86 64163 1.99 9698 1.77 107085 3.17 13793
3500 7.16 36374 4.35 7650 6.80 64163 7.29 9698 6.59 107085 11.79 13793
1750 3.58 489 36374 2.18 7650 3.40 515 64163 3.64 9698 3.29 531 107085 5.89 13793
5 0 0 1160 2.37 36374 1.44 7650 2.25 64163 2.42 9698 2.18 107085 3.91 13793
875 1.79 36374 1.09 7650 1.70 64163 1.82 9698 1.65 107085 2.95 13793
3500 6.22 36374 3.78 7650 6.18 64163 6.62 9698 5.99 107085 10.71 13793
1750 3.11 563 36374 1.89 7650 3.09 566 64163 3.31 9698 3.00 584 107085 5.36 13793
5 6 0
1160 2.06 36374 1.25 7650 2.05 64163 2.20 9698 1.99 107085 3.55 13793
875 1.55 36374 0.94 7650 1.55 64163 1.66 9698 1.50 107085 2.68 13793
3500 5.35 36374 3.25 7650 5.38 64163 5.76 9698 5.21 107085 9.32 13793
1750 2.67 655 36374 1.62 7650 2.69 651 64163 2.88 9698 2.61 671 107085 4.66 13793
6 3 0
1160 1.77 36374 1.08 7650 1.78 64163 1.91 9698 1.73 107085 3.09 13793
875 1.34 36374 0.81 7650 1.34 64163 1.44 9698 1.30 107085 2.33 13793
3500 4.81 36374 2.92 7650 4.84 64163 5.19 9698 4.63 107085 8.27 13793
1750 2.41 727 36374 1.46 7650 2.42 723 64163 2.59 9698 2.31 757 107085 4.14 13793
7 0 0 1160 1.60 36374 0.97 7650 1.60 64163 1.72 9698 1.53 107085 2.74 13793
875 1.20 36374 0.73 7650 1.21 64163 1.30 9698 1.16 107085 2.07 13793
3500 4.44 38055 2.82 7650 4.47 64163 4.79 9698 4.33 108855 7.87 13793
1750 2.22 789 38055 1.41 7650 2.23 783 64163 2.39 9698 2.16 809 108855 3.93 13793
8 0 0 1160 1.47 38055 0.93 7650 1.48 64163 1.59 9698 1.43 108855 2.61 13793
875 1.109 38055 0.71 7650 1.117 64163 1.20 9698 1.082 108855 1.97 13793
3500 3.72 38055 2.37 7650 3.87 64163 4.15 9698 3.70 107085 6.61 13793
1750 1.86 940 38055 1.18 7650 1.94 904 64163 2.07 9698 1.85 946 107085 3.31 13793
9 0 0 1160 1.23 38055 0.78 7650 1.28 64163 1.37 9698 1.23 107085 2.19 13793
875 0.930 38055 0.59 7650 0.968 64163 1.04 9698 0.924 107085 1.65 13793
3500 3.41 36374 2.07 7650 3.57 64163 3.83 9698 3.46 108855 6.29 13793
1750 1.70 1028 36374 1.03 7650 1.79 980 64163 1.91 9698 1.73 1012 108855 3.15 13793
1 0 c
1160 1.129 36374 0.69 7650 1.184 64163 1.27 9698 1.147 108855 2.08 13793
875 0.851 36374 0.52 7650 0.893 64163 0.96 9698 0.865 108855 1.57 13793

75
 SERIES K
QUINTUPLE REDUCTION RATINGS
SIZES K09 - K12
Pm - Input Power (HP) N2 - Output Speed (rpm)
M2 - Output Torque (lb.in) fra - Overhung Load (lbf)
i - Exact Ratio (:1)
QUINTUPLE REDUCTION
Input K0951 K1051 K1251
Column
Entry Speed
N1 N2 i M2 Pm fra N2 i M2 Pm fra N2 i M2 Pm fra
6 7 8 (rpm) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf) (rpm) (:1) (lb.in) (HP) (lbf)
3500 3.14 38055 2.00 7650 2.99 64163 3.20 9698 3.07 108855 5.58 13793
1750 1.57 1115 38055 1.00 7650 1.49 1171 64163 1.60 9698 1.53 1140 108855 2.79 13793
1 1 c
1160 1.041 38055 0.66 7650 0.991 64163 1.06 9698 1.017 108855 1.85 13793
875 0.785 38055 0.50 7650 0.747 64163 0.80 9698 0.767 108855 1.40 13793
3500 2.94 38055 1.87 7650 2.76 64163 2.96 9698 2.86 107085 5.11 13793
1750 1.47 1190 38055 0.93 7650 1.38 1268 64163 1.48 9698 1.43 1226 107085 2.55 13793
1 2 c 1160 0.975 38055 0.62 7650 0.915 64163 0.98 9698 0.947 107085 1.69 13793
875 0.735 38055 0.47 7650 0.690 64163 0.74 9698 0.714 107085 1.28 13793
3500 2.37 38055 1.51 7650 2.38 64163 2.55 9698 2.30 108855 4.19 13793
1750 1.19 1477 38055 0.75 7650 1.19 1470 64163 1.28 9698 1.15 1519 108855 2.10 13793
1 4 c 1160 0.786 38055 0.50 7650 0.789 64163 0.85 9698 0.764 108855 1.39 13793
875 0.593 38055 0.38 7650 0.595 64163 0.64 9698 0.576 108855 1.05 13793
3500 2.13 38055 1.36 7650 2.14 64163 2.30 9698 2.04 108855 3.72 13793
1750 1.067 1641 38055 0.68 7650 1.071 1634 64163 1.15 9698 1.022 1712 108855 1.86 13793
1 6 c 0.707 38055 0.45 7650 0.710 64163 0.76 9698 0.678 108855 1.23 13793
1160
875 0.533 38055 0.34 7650 0.535 64163 0.57 9698 0.511 108855 0.93 13793
3500 2.01 38055 1.28 7650 2.00 64163 2.14 9698 1.93 108855 3.51 13793
1750 1.005 1741 38055 0.64 7650 0.998 1754 64163 1.07 9698 0.966 1811 108855 1.76 13793
1 8 c
1160 0.666 38055 0.42 7650 0.661 64163 0.71 9698 0.640 108855 1.16 13793
875 0.502 38055 0.32 7650 0.499 64163 0.53 9698 0.483 108855 0.88 13793
3500 1.81 38055 1.15 7650 1.80 64163 1.92 9698 1.71 108855 3.12 13793
1750 0.905 1935 38055 0.57 7650 0.898 1949 64163 0.96 9698 0.857 2042 108855 1.56 13793
2 0 c 1160 0.600 38055 0.38 7650 0.595 64163 0.64 9698 0.568 108855 1.03 13793
875 0.452 38055 0.29 7650 0.449 64163 0.48 9698 0.429 108855 0.78 13793
3500 1.65 38055 1.05 7650 1.64 64163 1.76 9698 1.57 108855 2.85 13793
1750 0.826 2118 38055 0.53 7650 0.820 2134 64163 0.88 9698 0.783 2236 108855 1.42 13793
2 2 c 1160 0.548 38055 0.35 7650 0.543 64163 0.58 9698 0.519 108855 0.94 13793
875 0.413 38055 0.26 7650 0.410 64163 0.44 9698 0.391 108855 0.71 13793
3500 1.35 38055 0.86 7650 1.37 64163 1.46 9698 1.30 108855 2.37 13793
1750 0.674 2596 38055 0.43 7650 0.683 2561 64163 0.73 9698 0.652 2683 108855 1.19 13793
2 5 c 1160 0.447 38055 0.28 7650 0.453 64163 0.49 9698 0.432 108855 0.79 13793
875 0.337 38055 0.21 7650 0.342 64163 0.37 9698 0.326 108855 0.59 13793
3500 1.28 38055 0.81 7650 1.26 64163 1.35 9698 1.21 108855 2.20 13793
1750 0.640 2733 38055 0.41 7650 0.630 2779 64163 0.67 9698 0.606 2887 108855 1.10 13793
2 8 c
1160 0.424 38055 0.27 7650 0.417 64163 0.45 9698 0.402 108855 0.73 13793
875 0.320 38055 0.20 7650 0.315 64163 0.34 9698 0.303 108855 0.55 13793
3500 1.170 38055 0.74 7650 1.150 64163 1.23 9698 1.107 108855 2.01 13793
1750 0.585 2992 38055 0.37 7650 0.575 3044 64163 0.62 9698 0.553 3162 108855 1.01 13793
3 2 c 1160 0.388 38055 0.25 7650 0.381 64163 0.41 9698 0.367 108855 0.67 13793
875 0.292 38055 0.19 7650 0.287 64163 0.31 9698 0.277 108855 0.50 13793
3500 0.954 38055 0.61 7650 0.958 64163 1.03 9698 0.922 108855 1.68 13793
1750 0.477 3667 38055 0.30 7650 0.479 3652 64163 0.51 9698 0.461 3794 108855 0.84 13793
3 6 c 1160 0.316 38055 0.20 7650 0.318 64163 0.34 9698 0.306 108855 0.56 13793
875 0.239 38055 0.15 7650 0.240 64163 0.26 9698 0.231 108855 0.42 13793
3500 0.865 38055 0.55 7650 0.832 64163 0.89 9698 0.828 108855 1.51 13793
1750 0.432 4048 38055 0.27 7650 0.416 4208 64163 0.45 9698 0.414 4226 108855 0.75 13793
4 0 c
1160 0.287 38055 0.18 7650 0.276 64163 0.30 9698 0.275 108855 0.50 13793
875 0.216 38055 0.14 7650 0.208 64163 0.22 9698 0.207 108855 0.38 13793
3500 0.776 38055 0.49 7650 0.723 64163 0.77 9698 0.720 108855 1.31 13793
1750 0.388 4512 38055 0.25 7650 0.361 4842 64163 0.39 9698 0.360 4862 108855 0.65 13793
4 5 c
1160 0.257 38055 0.16 7650 0.240 64163 0.26 9698 0.239 108855 0.43 13793
875 0.194 38055 0.123 7650 0.181 64163 0.19 9698 0.180 108855 0.33 13793
3500 0.692 38055 0.44 7650 0.651 64163 0.70 9698 0.685 107085 1.23 13793
1750 0.346 5060 38055 0.22 7650 0.325 5380 64163 0.35 9698 0.342 5110 107085 0.61 13793
5 0 c 1160 0.229 38055 0.146 7650 0.216 64163 0.23 9698 0.227 107085 0.41 13793
875 0.173 38055 0.110 7650 0.163 64163 0.17 9698 0.171 107085 0.31 13793
3500 0.604 36374 0.37 7650 0.599 64163 0.64 9698 0.595 107085 1.06 13793
1750 0.302 5793 36374 0.18 7650 0.299 5845 64163 0.32 9698 0.298 5879 107085 0.53 13793
5 6 c 1160 0.200 36374 0.122 7650 0.198 64163 0.21 9698 0.197 107085 0.35 13793
875 0.151 36374 0.092 7650 0.150 64163 0.16 9698 0.149 107085 0.27 13793
3500 0.564 38055 0.36 7650 0.534 64163 0.57 9698 0.526 108855 0.96 13793
1750 0.282 6207 38055 0.18 7650 0.267 6548 64163 0.29 9698 0.263 6657 108855 0.48 13793
6 3 c 1160 0.187 38055 0.119 7650 0.177 64163 0.19 9698 0.174 108855 0.32 13793
875 0.141 38055 0.090 7650 0.134 64163 0.143 9698 0.131 108855 0.24 13793
3500 0.501 38055 0.32 7650 0.481 64163 0.52 9698 0.494 108855 0.90 13793
1750 0.251 6980 38055 0.16 7650 0.241 7276 64163 0.26 9698 0.247 7083 108855 0.45 13793
7 1 c
1160 0.166 38055 0.106 7650 0.159 64163 0.17 9698 0.164 108855 0.30 13793
875 0.125 38055 0.080 7650 0.120 64163 0.129 9698 0.124 108855 0.22 13793

76
 SERIES K
DIMENSIONS
TRIPLE REDUCTION
k
q q1 T2 w7

U
o o
z

D
e
a
T
n0

L1
L14 L13 Output Shaft Bore

g2
d1
h1 m1
b0
f0

p3
m2 Setscrews Holes
v3 øs

h
a3

m3
n Tapped m m
c

a2 Hole w1

u1
b

ød1
f t1

Input Shaft
SIZE a a2 a3 b b0 c e f f0 g2 h h1
K0332 3.94 1.10 1.26 4.33 4.53 0.43 4.72 5.63 5.98 5.51 3.94 0.63
K0432 4.72 1.38 1.46 5.12 5.12 0.63 5.71 6.61 6.73 5.51 4.41 0.51
K0532 5.12 1.18 1.77 5.12 5.91 0.59 6.18 6.69 7.56 7.09 5.20 0.20
K0632 5.51 1.18 1.77 4.72 6.30 0.79 6.69 6.93 8.19 7.09 5.51 0.51
K0732 6.50 1.57 2.17 5.91 7.87 1.06 7.87 8.27 10.35 8.35 7.09 0.98
K0832 7.09 2.17 2.76 7.09 9.17 1.18 9.06 10.08 12.17 9.84 8.35 0.59
K0931 9.45 2.95 2.95 9.45 11.61 1.38 11.42 13.39 15.55 11.81 10.43 0.39
K1031 10.63 3.74 3.74 11.02 14.17 1.57 13.39 15.35 17.91 14.17 12.40 1.61
K1231 12.99 4.53 4.33 13.78 16.54 1.77 15.75 18.50 21.26 15.75 14.76 2.56

SIZE k n n0 o p3 q q1 T2 s w7 z
K0332 13.11 1.50 1.50 2.36 6.57 2.48 6.26 4.37 0.43 2.48 0.00
K0432 14.21 1.50 1.57 2.95 7.36 2.80 7.05 4.37 0.43 3.07 0.10
K0532 16.14 1.57 1.57 3.27 8.54 3.15 8.62 4.37 0.55 3.43 0.18
K0632 16.93 2.17 1.89 3.54 9.17 3.54 9.02 4.37 0.55 3.70 0.20
K0732 19.37 2.36 2.17 4.13 11.34 4.41 10.43 4.53 0.71 4.29 0.20
K0832 24.49 2.99 2.99 4.72 13.43 5.20 12.99 6.30 0.91 4.88 0.20
K0931 27.95 3.94 3.94 5.91 16.54 6.30 13.98 7.68 1.06 6.06 0.20
K1031 33.70 4.33 4.53 6.89 20.20 7.87 16.65 9.17 1.34 7.09 0.20
K1231 38.86 4.72 4.72 8.07 23.23 8.86 18.74 11.26 1.54 8.27 0.20

Input Shaft Hollow Output Bore

SIZE
d1 L1 L14 t1 u1 w1 D m m1 m2 m3 T U v3
0.6250
K0332 1.57 19/32 0.70 3/16 1/4 UNF x .63 deep 1.25 2.070 4.724 4.130 1.260 1.377 0.250 3/8 UNF x 2
0.6245
0.6250
K0432 1.57 19/32 0.70 3/16 1/4 UNF x .63 deep 1.38 2.600 5.906 5.120 1.380 1.525 0.313 1/2 UNF x 21/4
0.6245
0.7500
K0532 1.57 19/32 0.83 3/16 1/4 UNF x .63 deep 1.50 2.870 6.535 5.590 1.510 1.675 0.375 5/8 UNF x 23/4
0.7495
0.7500
K0632 1.57 19/32 0.83 3/16 1/4 UNF x .63 deep 1.50 3.150 7.087 6.140 1.510 1.675 0.375 5/8 UNF x 23/4
0.7495
0.8750
K0732 1.97 19/32 0.96 3/16 5/16 UNF x .63 deep 2.00 3.640 8.268 7.200 2.020 2.230 0.500 5/8 UNF x 23/4
0.8745
1.1250
K0832 2.36 2 1.23 1/4 3/8 UNF x .87 deep 2.38 4.134 9.449 8.268 2.382 2.656 0.625 3/4-16 UNF x 31/4
1.1245
1.3750
K0931 3.15 213/32 1.51 5/16 1/2 UNF x 1.10 deep 2.75 5.217 11.811 10.630 2.772 3.037 0.625 3/4-16 UNF x 31/4
1.3745
1.6250
K1031 4.33 1.79 3/8 5/8 UNF x 1.42 deep 3.25 6.102 13.780 12.323 3.268 3.591 0.750 3/4-16 UNF x 31/4
1.6240 311/16
2.1250
K1231 4.33 313/16 2.35 1/2 3/4 UNF x 1.65 deep 4.00 7.087 16.142 14.685 4.020 4.446 1.000 1-12 UNF x 41/2
2.1240

77
 SERIES K
DIMENSIONS
QUINTUPLE REDUCTION
k w7
q q1 T2 o o
z
e
a

u1
n0

ød1
L1

v3
L14 L13
t1

g6
Input Shaft

d2

g2
h1
b0
f0

p3
v2
Holes
øs

h
Tapped
a3

Hole w1
m1
n m2 Setscrews
c

a2

U
v3
b

øD
f
m3 T
m m
Output Shaft Bore

SIZE a a2 a3 b b0 c e f f0 g2 g6 h h1
K0352 3.94 1.10 1.26 4.33 4.53 0.43 4.72 5.63 5.98 5.51 5.51 3.94 0.63
K0452 4.72 1.38 1.46 5.12 5.12 0.63 5.71 6.61 6.73 5.51 5.51 4.41 0.51
K0552 5.12 1.18 1.77 5.12 5.91 0.59 6.18 6.69 7.56 5.51 7.09 5.20 0.20
K0652 5.51 1.18 1.77 4.72 6.30 0.79 6.69 6.93 8.19 5.51 7.09 5.51 0.51
K0752 6.50 1.57 2.17 5.91 7.87 1.06 7.87 8.27 10.35 5.51 7.09 7.09 0.98
K0852 7.09 2.17 2.76 7.09 9.17 1.18 9.06 10.08 12.17 7.09 9.84 8.35 0.59
K0951 9.45 2.95 2.95 9.45 11.61 1.38 11.42 13.39 15.55 7.09 11.81 10.43 0.39
K1051 10.63 3.74 3.74 11.02 14.17 1.57 13.39 15.35 17.91 8.35 14.17 12.40 1.61
K1251 12.99 4.53 4.33 13.78 16.54 1.77 15.75 18.50 21.26 8.35 15.75 14.76 2.56

SIZE k n n0 o p3 q q1 T2 s w7 z v2 v3
K0352 24.80 1.50 1.50 2.36 6.57 2.48 6.26 4.37 0.43 2.48 0.00 2.99 -
K0452 25.91 1.50 1.57 2.95 7.36 2.80 7.05 4.37 0.43 3.07 0.10 2.99 -
K0552 28.46 1.57 1.57 3.27 8.54 3.15 8.62 4.37 0.55 3.43 0.18 3.58 -
K0652 29.25 2.17 1.89 3.54 9.17 3.54 9.02 4.37 0.55 3.70 0.20 3.58 -
K0752 31.57 2.36 2.17 4.13 11.34 4.41 10.43 4.37 0.71 4.29 0.20 3.58 -
K0852 36.57 2.99 2.99 4.72 13.43 5.20 12.99 4.37 0.91 4.88 0.20 4.53 -
K0951 39.09 3.94 3.94 5.91 16.54 6.30 13.98 4.37 1.06 6.06 0.20 4.53 -
K1051 45.08 4.53 4.33 6.89 20.20 7.87 16.65 4.53 1.34 7.09 0.20 5.51 6.10
K1251 50.08 4.72 4.72 8.07 23.23 8.86 18.74 4.53 1.54 8.27 0.20 5.51 6.10

Input Shaft Hollow Output Bore

SIZE
d1 L1 L14 t1 u1 w1 D m m1 m2 m3 T U v3
0.625
K0352 1.57 19/32 0.7 3/16 1/4 UNF x .63 deep 1.25 2.07 4.724 4.13 1.26 1.377 0.25 3/8 UNF x 2
0.6245
0.625
K0452 1.57 19/32 0.7 3/16 1/4 UNF x .63 deep 1.375 2.6 5.906 5.12 1.38 1.525 0.313 1/2 UNF x 21/4
0.6245
0.625
K0552 1.57 19/32 0.7 3/16 1/4 UNF x .63 deep 1.5 2.87 6.535 5.59 1.51 1.675 0.375 5/8 UNF x 23/4
0.6245
0.625
K0652 1.57 19/32 0.7 3/16 1/4 UNF x .63 deep 1.5 3.15 7.087 6.14 1.51 1.675 0.375 5/8 UNF x 23/4
0.6245
0.625
K0752 1.57 19/32 0.7 Mar-16 1/4 UNF x .63 deep 2 3.64 8.268 7.2 2.02 2.23 0.5 5/8 UNF x 23/4
0.6245
0.75
K0852 1.57 19/32 0.83 3/16 1/4 UNF x .63 deep 2.375 4.134 9.449 8.268 2.382 2.656 0.625 3/4-16 UNF x 31/4
0.7495
0.75
K0951 1.57 19/32 0.83 3/16 1/4 UNF x .63 deep 2.75 5.217 11.811 10.63 2.772 3.037 0.625 3/4-16 UNF x 31/4
0.7495
0.875
K1051 1.97 19/32 0.96 3/16 5/16 UNF x .63 deep 3.25 6.102 13.78 12.323 3.268 3.591 0.75 3/4-16 UNF x 31/4
0.8745
0.875
K1251 1.97 19/32 0.96 3/16 5/16 UNF x .63 deep 4 7.087 16.142 14.685 4.02 4.446 1 1-12 UNF x 41/2
0.8745
78
 SERIES K
THERMAL POWER
RATINGS
Thermal Ratings HP 60 Hz Speeds
Thermal ratings are a measure of the units ability to dissipate heat. If they are exceeded, the lubricant may break down resulting in
premature gear failure.
Thermal ratings are based on an ambient temperature of 68oF (20oC), where units are to operate in other ambient temperatures thermal
ratings must be adjusted by the following factors.

Ratios input rpm K03 K04 K05 K06 K07 K08 K09 K10 K12
3500 Consult Application Engineers
Units
with no 1750 8.7 10.6 15.4 16.4 24.1 32.2 42.9 61.7 70.7
8 to 20 additional 1175 9.1 11.1 16.1 17.2 25.3 33.7 44.9 65 74
cooling
875 8.1 9.8 14.2 15.2 22.3 29.8 39.7 57 65
3500 5.4 6.5 9.4 10.1 14.9 19.9 26.5 38.1 50.2
Units
with no 1750 7.4 8.9 12.9 14.0 20.6 27.4 36.6 52.6 69.3
22 to 40 additional 1175 7.1 8.5 12.3 13.4 19.7 26.2 35.0 50 66
cooling
875 6.8 8.2 12.0 12.9 19.0 25.4 33.9 49 64
3500 4.8 5.7 8.3 9.6 14.2 18.9 41.6 36.2 49.2
Units
with no 1750 6.6 7.9 11.4 13.3 19.5 26.1 57.3 49.9 67.9
45 & over additional 1175 6.3 7.5 10.9 12.7 18.7 24.9 54.8 47.7 64.8
cooling
875 6.8 8.2 12.0 12.9 19.0 25.4 33.9 49 64
3500 N/A N/A N/A N/A N/A N/A N/A N/A N/A
Units
with no 1750 - - - - 54 72 97 139 159
8 to 20 additional 1175 - - - - 45 60 79 114 131
cooling
875 - - - - 40 53 71 102 117
3500 N/A N/A N/A N/A N/A N/A N/A N/A N/A
Units
with no 1750 - - - - 46 62 82 118 156
22 to 40 additional 1175 - - - - 38 51 68 97 128
cooling
875 - - - - 34 45 60 87 114
3500 N/A N/A N/A N/A N/A N/A N/A N/A N/A
Units
with no 1750 - - - - 44 59 129 112 153
45 & over additional 1175 - - - - 36 48 106 92 126
cooling
875 - - - - 32 43 95 82 112

Note: When checking thermal capacities use actual load required to be transmitted, not rating of prime mover.

79
 SERIES K
FAN COOLED UNITS
Column 10 Entry
For reducer fan kit modules enter S in column 10

or if used in conjunction with a reducer backstop module kit Y CW rotation

Z CCW rotation

Dimensions of Fan Cooled Units

k
q L15

øB8
Shaft end
detail as
standard unit

Unit øB8 k L15 q

Size

K0732 8.86 19.37 1.38 4.41

K0832 10.43 24.49 1.77 5.20

K0931 12.60 27.95 2.56 6.30

K1031 14.96 33.70 3.74 7.87

K1231 16.54 38.86 3.35 8.86

80
 SERIES K
REDUCER BACKSTOP
MODULE
The reducer units listed below can be fitted with an internal backstop, this has no effect of the external unit size. The backstop device
incorporates high quality centrifugal lift off sprags which are wear free above the lift off speed (n min). To ensure correct operation input
speed must exceed lift off speed.

Suitable for ambient temperature -22oF to + 122oF

Column 10 Entry
For reducer backstop modules enter W for CCW rotation (or Z if used in conjunction with a fan kit)

X for CW rotation (or Y if used in conjunction with a fan kit)

Lift off Rated

Speed (‘n’ min)
Unit Locking Torque (‘T
(at inputshaft)
Size max’)
(rev/min) (at inputshaft) (lb.in)

K0532 800 885

K0632 800 885

K0732 670 1505

K0832 670 1505

K0931 670 2655

K1031 670 2655

K1231 550 21240

Rotation of outputshaft must be specified when ordering as viewed from the

outputshaft end (as shown in the diagram)

CW - Free Rotation - Clockwise

Locked - Anticlockwise

AC - Free Rotation - Anticlockwise

Locked - Clockwise CW

81
 SERIES K
DIMENSIONS
OUTPUTSHAFT OPTIONS
STANDARD OUTPUTSHAFT OPTION

w7 O
Tapped Hole
w

ød
t
L12 L11
Output Shaft

Size ød i L L12 O t u w w7
K0332 1.0000 / 0.9995 2.36 1.85 1.44 4.33 1.106 0.250 3/8 UNF x 0.75” Deep 2.48
K0432 1.2500 / 1.2495 2.95 2.20 2.00 5.31 1.359 0.250 1/2 UNF x 1.13” Deep 3.07
K0532 1.3750 / 1.3745 3.46 2.60 2.38 6.02 1.507 0.313 5/8 UNF x 1.5” Deep 3.43
K0632 1.625 / 1.624 3.98 3.00 2.38 6.73 1.784 0.375 5/8 UNF x 1.5” Deep 3.70
K0732 2.000 / 1.999 4.86 3.74 2.75 8.11 2.228 0.500 5/8 UNF x 1.5” Deep 4.29
K0832 2.375 / 2.374 5.91 4.49 3.69 9.45 2.650 0.625 3/4” 16 UNF x 1.65 Deep 4.88
K0931 2.875 / 2.874 6.73 5.32 4.63 11.46 3.200 0.750 3/4” 16 UNF x 1.65 Deep 6.06
K1031 3.625 / 3.624 8.35 6.77 5.94 13.66 4.010 0.875 3/4” 16 UNF x 1.65 Deep 7.09
K1231 4.375 / 4.374 9.96 8.39 6.50 16.46 4.810 1.000 1” 12 UNF x 2.17 Deep 8.27

STANDARD DOUBLE EXTENDED OUTPUTSHAFT OPTION

Tapped Hole O O
Tapped Hole
w w

L L
u

ød

t
L11 L12 L12 L11
Output Shaft all parallel keys are to DIN 6885

i i

Size d i L L12 O t u w
K0332 1.0000 / 0.9995 2.36 1.85 1.44 4.33 1.106 0.250 3/8 UNF x 0.75” Deep
K0432 1.2500 / 1.2495 2.95 2.20 2.00 5.31 1.359 0.250 1/2 UNF x 1.13” Deep
K0532 1.3750 / 1.3745 3.46 2.60 2.38 6.02 1.507 0.313 5/8 UNF x 1.5” Deep
K0632 1.4996 / 1.4990 3.98 3.00 2.38 6.73 1.664 0.375 5/8 UNF x 1.5” Deep
K0732 2.000 / 1.999 4.86 3.74 2.75 8.11 2.228 0.500 5/8 UNF x 1.5” Deep
K0832 2.3746 / 2.3739 5.91 4.49 3.69 9.45 2.650 0.625 3/4” 16 UNF x 42 Deep
K0931 2.625 / 2.624 6.73 5.32 3.69 11.46 3.030 0.625 3/4” 16 UNF x 42 Deep
K1031 3.125 / 3.124 7.99 6.42 4.63 13.66 3.450 0.750 3/4” 16 UNF x 42 Deep
K1231 3.875 / 3.874 9.45 7.87 6.50 16.46 4.310 1.000 1” 12 UNF x 55 Deep

82
 SERIES K
DIMENSIONS
SHRINK DISC
The gear unit is fitted with a ‘shrink disc’ device located on the hollow output shaft to provide a positive outer locking connection between gear unit
and driven shaft. The ‘shrink disc’ is a friction device, without keys, which exerts an external clamping force on the hollow output shaft, thus
establishing a mechanical shrink fit between the gear unit hollow shaft and driven shaft. ‘Shrink disc’ capacities have ample margins in dealing with
transmitted torques and external loading imposed on gear units.

WORKING PRINCIPLE

The ‘shrink disc’ consists of a locking collar, a tapered inner ring and locking screws. By tightening the locking screws, the locking collar and tapered
inner ring are pulled together, exerting radial forces on the inner ring, thus creating a positive friction connection between hollow shaft and driven
shaft.

As the tapered surfaces of locking collar and inner ring are lubricated with Molykote 321R or similar and the taper angle is not self locking, locking
collar will not seize on the inner ring and can be released easily when removal is necessary.

When the shrink disc is clamped in position the high contact pressures between tapered surfaces and screw heads and their
seatings ensure hermetic sealing and eliminate the possibility of fretting corrosion.

o w7
f4 o o1
Locking
Screw

øD +0.5
m5 m4
ød7

øD6
øD

Driven
øg4

Machine
Side

Customers Shaft

-0 .3
øD

øD
h6

h6
m7
øD

m6
R 1
.0
max

Note: only available as standard in

this handing, please contact
us for opposite handing

Locking
Screws
SIZE D D6 d7 f4 g4 m4 m5 m6 m7 o o1 w7 Torque
Ta
(lbf.in)

K03 1.181 1.181 1.97 0.10 3.48 1.22 0.79 1.42 0.98 2.36 3.39 3.58 257
K04 1.378 1.378 2.17 0.10 4.25 1.26 0.79 1.46 0.98 2.95 4.02 4.45 257
K05 1.575 1.575 2.36 0.12 4.25 1.42 0.79 1.61 0.98 3.27 4.41 4.65 257
K06 1.575 1.575 2.76 0.14 5.24 1.5 0.79 1.69 0.98 3.54 4.65 5.51 257
K07 1.969 1.969 3.15 0.24 5.24 1.42 1.18 1.61 1.38 4.13 5.35 5.98 310
K08 2.559 2.559 3.54 0.20 6.38 1.61 1.57 1.81 1.77 4.72 6.34 6.89 515
K09 2.953 2.953 3.94 0.20 6.89 2.17 1.57 2.36 2.17 5.91 7.68 8.27 515
K10 3.740 3.740 4.720 0.20 7.87 2.56 2.36 2.76 2.56 6.89 9.06 9.65 885
K12 4.134 4.134 5.51 0.20 9.45 3.35 2.36 3.54 2.95 8.07 11.02 11.61 1415

83
 SERIES K
DIMENSIONS (Inches)
TAPER RELEASE BUSHING
w7

o1 o
q
l

øg4
d

Driven
Machine
Side Protective
Cover

Motorized or
reducer
Note: only available as standard in this handing,
please contact us for opposite handing

Driven shaft Thin walled

Set Screw
Tapered Bushing
H
a b
W

Retaining
(h10)
ødk

Ring

Nut

m m
K Stepped key for u
a1 b1 Tapped hole driven shaft v
N (min) (supplied) w

Thick walled
End plate C1
Set Screw
(not supplied) Hollow shaft key Tapered Bushing
(supplied)
Retaining
Ring
øC

Nut

øK1 Square key for

hole driven shaft
(not supplied)
• Consult standard unit selection tables
for HP and torque ratings

Key Bush Hollow Shaft Nut Gear Unit Cover

SIZE
a b u v w d I m o o1 q g4 w7

K05 (107)TR 1.90 2.50 5.00 7.50 8.20 3.31 1.26 0.27 4.57 3.27 1.61 4.25 4.65

K06 (115)TR 2.10 2.75 5.55 8.50 9.88 4.06 1.46 0.30 5.04 3.54 1.77 5.24 5.51

K07 (203)TR 1.55 3.25 5.55 9.55 11.3 4.31 1.46 0.30 5.35 4.13 1.61 5.24 5.98

K08 (207)TR 1.24 4.25 6.11 10.0 11.0 4.81 1.46 0.30 6.56 4.72 2.03 6.38 6.89

K09 (215)TR 2.09 3.50 7.08 12.6 13.5 5.68 1.76 0.38 7.95 5.91 2.24 6.89 8.27

K10 (307)TR 1.59 5.00 7.39 14.0 15.62 6.06 1.76 0.38 9.10 6.89 2.41 7.87 9.65

K12 (315)TR 1.88 5.00 7.67 16.4 18.0 6.81 1.8 0.42 10.33 8.07 2.46 9.45 11.61

• All other gear unit dimensions may be obtained from the standard unit dimension pages

84
 SERIES K
DIMENSIONS (Inches)
TAPER RELEASE BUSHING
Driven shaft driven shaft keyway driven shaft end plate bushing
bushing
size diameter * width depth min length circlip weight
style a1 K N (min) øC C1 K1
(ødk) (W ) (H) (b1) (lbs)
1.000 / 0.996 Thick 1
/4 1
/8 2.75 - 1
/2 UNC 5.0 1.64 0.30 5
/8 UNC N1300-0162 2.1
1.125 / 1.121 Thick 1
/4 1
/8 2.75 - 1
/2 UNC 5.0 1.64 0.30 5
/8 UNC N1300-0162 1.8
K05 (107)TR 1.188 / 1.184 Thick 1
/4 1
/8 2.75 - 1
/2 UNC 5.0 1.64 0.30 5
/8 UNC N1300-0162 1.6
1.250 / 1.246 Thin 1
/4 1
/8 2.50 1.89 1
/2 UNC 5.0 1.64 0.30 5
/8 UNC N1300-0162 1.5
1.438 / 1.434 Thin 3
/8 3
/16 2.50 1.89 1
/2 UNC 5.0 1.64 0.30 5
/8 UNC N1300-0162 1.0
1.188 / 1.184 Thick 1
/4 1
/8 2.75 - 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 4.3
1.250 / 1.246 Thick 1
/4 1
/8 2.75 - 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 4.1
1.438 / 1.434 Thick 3
/8 3
/16 2.50 - 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 3.5
1.500 / 1.496 Thick 3
/8 3
/16 2.50 - 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 3.3
K06 (115)TR
1.625 / 1.620 Thin 3
/8 3
/16 2.75 2.10 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 2.9
1.688 / 1.683 Thin 3
/8 3
/16 2.75 2.10 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 2.7
1.750 / 1.745 Thin 3
/8 3
/16 2.75 2.10 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 2.4
1.938 / 1.933 Thin 1
/2 1
/4 2.75 2.10 1
/2 UNC 5.55 2.25 0.37 5
/8 UNC N1300-0225 1.7
1.438 / 1.434 Thick 3
/8 3
/16 2.75 - 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 5.0
1.500 / 1.496 Thick 3
/8 3
/16 2.75 - 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 5.1
1.625 / 1.620 Thick 3
/8 3
/16 2.75 - 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 4.6
1.688 / 1.683 Thick 3
/8 3
/16 2.75 - 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 4.4
K07 (203)TR 1.750 / 1.745 Thick 3
/8 3
/16 2.75 - 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 4.4
1.875 / 1.870 Thin 1
/2 1
/4 3.25 1.56 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 3.6
1.938 / 1.933 Thin 1
/2 1
/4 3.25 1.56 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 3.3
2.000 / 1.995 Thin 1
/2 1
/4 3.25 1.56 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 3.0
2.188 / 2.183 Thin 1
/2 1
/4 3.25 1.56 5
/8 UNC 5.55 2.43 0.43 3
/4 UNC N1300-0244 3.0
1.375 / 1.371 Thick 3
/16 5
/32 4.75 - 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 7.6
1.438 / 1.434 Thick 3
/8 3
/16 3.25 - 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 7.3
1.500 / 1.496 Thick 3
/8 3
/16 3.25 - 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 7.1
1.625 / 1.620 Thick 3
/8 3
/16 3.25 - 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 6.7
1.688 / 1.683 Thick 3
/8 3
/16 3.25 - 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 6.4
K08 (207)TR 1.750 / 1.745 Thick 3
/8 3
/16 3.25 - 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 6.1
1.875 / 1.870 Thick 1
/2 1
/4 3.25 - 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 5.6
1.938 / 1.933 Thin 1
/2 1
/4 4.25 1.24 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 5.3
2.000 / 1.995 Thin 1
/2 1
/4 4.25 1.24 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 5.0
2.188 / 2.183 Thin 1
/2 1
/4 4.25 1.24 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 4.4
2.250 / 2.245 Thin 1
/2 1
/4 4.25 1.24 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 3.7
2.438 / 2.433 Thin 5
/8 5
/16 4.25 1.24 5
/8 UNC 6.11 2.83 0.43 3
/4 UNC N1300-0281 2.6
1.938 / 1.933 Thick 1
/2 1
/4 5.25 - 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 11.4
2.000 / 1.995 Thick 1
/2 1
/4 5.25 - 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 11.1
2.188 / 2.183 Thick 1
/2 1
/4 5.25 - 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 9.9
2.250 / 2.245 Thick 1
/2 1
/4 5.25 - 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 9.5
K09 (215)TR
2.438 / 2.433 Thin 5
/8 5
/16 3.50 2.09 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 8.3
2.500 / 2.495 Thin 5
/8 5
/16 3.50 2.09 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 7.8
2.688 / 2.682 Thin 5
/8 5
/16 3.50 2.09 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 6.5
2.938 / 2.932 Thin 3
/4 3
/8 3.50 2.09 7
/8 UNC 7.08 3.33 0.50 1 UNC N1300-0334 4.5
2.000 / 1.995 Thick 1
/2 1
/4 5.25 - 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 17.8
2.188 / 2.183 Thick 1
/2 1
/4 5.25 - 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 16.6
2.250 / 2.245 Thick 1
/2 1
/4 5.25 - 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 16.2
2.438 / 2.433 Thick 5
/8 5
/16 5.25 - 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 14.9
2.500 / 2.495 Thick 5
/8 5
/16 5.25 - 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 14.4
K10 (307)TR
2.688 / 2.682 Thin 5
/8 5
/16 5.00 1.59 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 13.0
2.938 / 2.932 Thin 3
/4 3
/8 5.00 1.59 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 10.9
3.000 / 2.994 Thin 3
/4 3
/8 5.00 1.59 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 10.3
3.188 / 3.182 Thin 3
/4 3
/8 5.00 1.59 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 8.6
3.438 / 3.432 Thin 7
/8 7
/16 5.00 1.59 1 UNC 7.39 3.74 0.56 1 1
/8 UNC N1300-0375 6.1
2.438 / 2.433 Thick 5
/8 5
/16 5.25 - 1 UNC 7.92 4.32 0.75 1 1
/8 UNC N1300-0433 23.6
2.500 / 2.495 Thick 5
/8 5
/16 5.25 - 1 UNC 7.92 4.32 0.75 1 1
/8 UNC N1300-0433 23.1
2.688 / 2.682 Thick 5
/8 5
/16 5.25 - 1 UNC 7.92 4.32 0.75 1 1
/8 UNC N1300-0433 21.6
K12 (315)TR 2.938 / 2.932 Thick 3
/4 3
/8 5.00 - 1 UNC 7.92 4.32 0.75 1 1
/8 UNC N1300-0433 19.4
3.000 / 2.994 Thick 3
/4 3
/8 5.00 - 1 UNC 7.92 4.32 0.75 1 1
/8 UNC N1300-0433 18.8
3.438 / 3.432 Thin 7
/8 7
/16 5.00 1.88 1 UNC 7.92 4.32 0.75 1 1
/8 UNC N1300-0433 14.3
3.938 / 3.932 Thin 1.0 1
/2 5.00 1.88 1 UNC 7.92 4.32 0.75 1 1
/8 UNC N1300-0433 8.4

* Check strength of driven shaft

Check strength and length of key (when key not supplied ie thick wall bushing)

85
 SERIES K
DIMENSIONS
P
TORQUE BRACKET

a4 i i

Column 9 Entry Column 9 Entry

T Torque bracket Q Torque bracket
on left on right
The torque
arm requires a
Stirrup type
anchoring

ød1
l2 G

l1

SIZE a4 d1 G i I1 I2 P R

0.413
K03 0.93 0.08 0.79 1.42 1.26 5.51 0.79
0.406

0.413
K04 1.18 0.08 0.79 1.42 1.26 6.3 0.79
0.406

0.650
K05 1.57 0.08 0.71 2.36 2.20 7.56 1.38
0.642

0.650
K06 1.77 0.08 0.98 2.36 2.20 7.87 1.38
0.642

0.650
K07 2.07 0.08 0.98 2.36 2.20 9.84 1.38
0.642

0.994
K08 2.36 0.20 1.18 3.15 2.76 11.81 1.57
0.974

0.994
K09 2.76 0.20 1.57 3.94 3.54 13.78 1.57
0.974

0.994
K10 2.91 0.20 1.77 3.94 3.54 17.72 1.57
0.974

1.506
K12 2.36 0.31 0.39 4.96 4.33 21.65 2.28
1.486

NOTES:
It is recommended that the torque arm is fitted on the side of the unit adjacent to the driven machine.
The use of a fitted bolt is recommended.

86
 SERIES K
DIMENSIONS
ALL UNITS
STANDARD UNIT WITH B5 (D) FLANGE

Sizes K09 to K12 Sizes K03 to K08

8 Holes
s1 dia
4 Holes

1
s1 dia

øe
1
øe

Mo
Mo

Column 9 Entry Column 9 Entry

F B5 (D) Output Flange on Left H B5 (D) Output Flange on Right
A4 f1

Tapped Hole
v
L

u
øb1

øa1

ød
L12
t
X1

Output Shaft
Note: Flange can be supplied as
c1 standard with an extended
output shaft

i2 Column 11 Entry G
o

SIZE Øa1 a4 Øb1 c1 Øe1 f1 h m Øs1

K03 6.3 5.67 4.33 j6 0.39 5.12 0.14 3.94 45° 0.35
K04 7.87 7.48 5.12 j6 0.47 6.5 0.14 4.41 45° 0.43
K05 9.84 7.44 7.09 j6 0.63 8.46 0.16 5.2 45° 0.55
K06 9.84 8.66 7.09 j6 0.63 8.46 0.16 5.51 45° 0.55
K07 11.81 9.72 9.06 j6 0.71 10.43 0.16 7.09 45° 0.55
K08 13.78 11.22 9.84 h6 0.71 11.81 0.2 8.35 45° 0.71
K09 17.72 13.82 13.78 h6 0.79 15.75 0.2 10.43 22.5° 0.71
K10 17.72 16.16 13.78 h6 0.87 15.75 0.2 12.4 22.5° 0.71
K12 17.72 18.52 13.78 h6 0.87 15.75 0.2 14.76 22.5° 0.71

Inch Extended Output shaft - Column 11 Entry G

SIZE
d i2 L L12 o t u v
K0332 1.0000 / 0.9995 1.97 1.97 1.57 5.28 1.106 0.25 3/8 UNF x 0.75” Deep
K0432 1.2500 / 1.2495 2.36 2.36 1.97 6.89 1.359 0.25 1/2 UNF x 1.13” Deep
K0532 1.3750 / 1.3745 2.76 2.76 2.36 6.93 1.507 0.313 5/8 UNF x 1.5” Deep
K0632 1.625 / 1.624 3.15 3.15 2.76 8.27 1.784 0.375 5/8 UNF x 1.5” Deep
K0732 2.000 / 1.999 3.94 3.94 3.15 9.53 2.228 0.5 5/8 UNF x 1.5” Deep
K0832 2.375 / 2.374 4.72 4.72 3.94 11.22 2.65 0.625 3/4” 16 UNF x 1.65 Deep
K0931 2.875 / 2.874 5.51 5.51 4.33 13.43 3.2 0.75 3/4” 16 UNF x 1.65 Deep
K1031 3.625 / 3.624 6.69 6.69 5.51 15.96 4.01 0.875 3/4” 16 UNF x 1.65 Deep
K1231 4.375 / 4.374 8.27 8.27 7.09 18.72 4.81 1 1” 12 UNF x 2.17 Deep

87
 SERIES K
DIMENSIONS
ALL UNITS
K03, K04 & K08 K05 K06
øQ øQ
øQ

5
øe
22 .5 o
5
øe

45
o
30 o

30
o
22.5 22.5 o

22.5 22.5 o

o
øe5

30 o
30

o
o

45
o

F7

22.5 o

K07 K09
øQ øQ

øe5

5
øe
45 o

45
o
o2 o2

30 o

30
o
f F

30 o
45 o

30
o
45
øR
ør

K10 K12
øQ øQ

36 o 36 o

5 5
øe øe

18o 18 o
18o 18 o
18o 18 o

18o 18 o

Male spigot Female recess

K03 - K07 K08 - K12
36 36 o 36
36 o o o

Ør (h7) Spigot Recess

SIZE Øe5 F7 o2 ØQ ØR (H7)
spigot Ø f F
K03 4.21 6 Holes M8 x 1.25, 0.47 Deep 2.17 4.8 3.346 - 0.1 -
K04 5.12 6 Holes M8 x 1.25, 0.47 Deep 2.76 5.75 4.134 - 0.1 -
K05 4.92 6 Holes M10 x 1.5, 0.67 Deep 2.95 5.91 4.134 - 0.12 -
K06 5.91 6 Holes M10 x 1.5, 0.67 Deep 3.27 7.09 5.118 - 0.14 -
K07 5.91 8 Holes M10 x 1.5, 0.67 Deep 3.74 7.09 5.118 - 0.24 -
K08 7.68 6 Holes M12 x 1.75, 0.79 Deep 4.53 8.66 - 5.906 - 0.2
K09 9.06 5 Holes M16 x 2.0, 1.06 Deep 5.71 10.24 - 7.087 - 0.24
K10 11.02 8 Holes M16 x 2.0, 1.06 Deep 6.69 12.2 - 8.268 - 0.28
K12 11.02 9 Holes M16 x 2.0, 1.06 Deep 7.87 12.2 - 8.268 - 0.28

88
 SERIES K
DIMENSIONS
STANDARD BORE ASSEMBLY
ASSEMBLY ONTO SHAFT - CUSTOMERS SHAFT DETAIL

T
l5
R

da

d
d
d
u1

m
Spacer tube for l3 l4
use with l2 l1
customer shaft l
without shoulder
(Not supplied)

SIZE d da I I1 I2 I3 I4 I5 m N R T u u1

1.2496 3/8 x UNF 0.875 12 1.112 0.252

K03 1.23 3.23 1.77 0.59 3 0.12 0.91 0.03 0.01
1.2490 deep lb.ft 1.106 0.25

1.3746 15 1.201 0.3145

K04 1.36 4.29 2.36 0.79 3.56 0.12 0.91 1/2 x UNF 1.25 deep 0.03 0.01
1.3740 lb.ft 1.195 0.3125

1.4996 35 1.289 0.377

K05 1.48 4.41 2.36 0.79 3.63 0.12 1.18 5/8 x UNF 1.69 deep 0.03 0.01
1.4990 lb.ft 1.283 0.375

1.4996 35 1.289 0.377

K06 1.48 4.96 2.95 0.98 4 0.12 1.18 5/8 x UNF 1.69 deep 0.03 0.01
1.4990 lb.ft 1.283 0.375

1.9996 35 1.718 0.502

K07 1.98 6.02 3.54 1.18 5 0.12 1.18 5/8 x UNF 1.42 deep 0.03 0.02
1.9990 lb.ft 1.712 0.5

2.3746 60 2.021 0.627

K08 2.35 6.81 3.54 1.18 5 0.12 1.45 3/4 x UNF 1.65 deep 0.03 0.02
2.3739 lb.ft 2.006 0.625

2.7496 60 2.402 0.627

K09 2.73 9.13 4.13 1.38 5.35 0.12 1.5 3/4 x UNF 1.65 deep 0.03 0.02
2.7489 lb.ft 2.387 0.625

3.2495 60 2.831 0.752

K10 3.23 10.83 4.72 1.57 6.75 0.2 1.45 3/4 x UNF 1.65 deep 0.03 0.02
3.2486 lb.ft 2.816 0.75

3.9995 160 3.436 1.002

K12 3.98 12.87 5.91 1.97 7.5 0.39 1.81 1 x UNF 2 deep 0.03 0.02
3.9986 lb.ft 3.421 1.000

Assembly Instructions

1. Spray the hollow shaft bore and mating diameter of the output shaft with Rocol DFSM or equivalent antiscuffing spray.

2. Fit key into shaft.

3. Fit the circlip into the output sleeve.

4. Fit the spacer tube only if the output shaft has no shoulder, then fit the output shaft into the output sleeve.

5. Secure in place with the washer and bolt. Torque tighten to the values stated in column N of the above table.

89
 SERIES K
DIMENSIONS
STANDARD BORE DISASSEMBLY
DISASSEMBLY METHOD FROM SHAFT

c4

*
D d3

* PARTS SUPPLIED BY CUSTOMER u

*
*

m1
m1
d2

d3
m

1 x 45o c5

l2

SIZE c4 c5 D d2 d3 I2 m m1 t (max) U (max)

K03 0.2 0.59 1.25 0.5 1.245 6 0.2 5/8 UN 1.35 0.25

K04 0.2 0.59 1.375 0.5 1.37 6 0.2 5/8 UN 1.5 0.313

K05 0.2 0.79 1.5 0.81 1.495 7 0.2 1 UN 1.65 0.375

K06 0.2 0.79 1.5 0.81 1.495 7 0.2 1 UN 1.65 0.375

K07 0.2 0.79 2 0.81 1.995 8.5 0.2 1.0 UN 2.2 0.5

K08 0.31 0.94 2.375 1 2.37 10 0.2 1.25 UN 2.63 0.625

K09 0.31 0.94 2.75 1 2.745 12.5 0.2 1.25 UN 3.01 0.625

K10 0.31 0.94 3.25 1 3.245 14 0.2 1.25 UN 3.57 0.75

K12 0.31 1.15 4 1.23 3.995 16.5 0.2 1.5 UN 4.42 1

90
 SERIES K
SHIPPING SPECIFICATION
SHIPPING WEIGHT (lbs)

K0332

K0352

K0432

K0452

K0532

K0552

K0632

K0652

K0732

K0752

K0832

K0852

K0932

K0952

K1032

K1052

K1232

K1252
UNIT SIZE AND NUMBER
OF REDUCTIONS

REDUCER VERSION 35 53 46 64 71 95 88 112 134 154 249 306 384 434 675 708 1010 1069
OUTPUT SHAFT 2 2 2 2 3 3 4 4 8 8 13 13 24 24 41 41 76 76
OUPUT FLANGE 3 3 6 6 9 9 12 12 15 15 33 33 37 37 57 57 57 57
Without Motor 38 57 50 68 69 99 86 117 129 157 257 306 434 771 1063
56C
With Motor 63 82 75 93 94 124 111 142 154 182 282 331 459 796 1088
Without Motor 38 57 50 68 69 99 86 117 129 157 257 306 434 771 1063
143TC
With Motor 68 87 80 98 99 129 116 147 159 187 287 336 464 801 1093
Without Motor 38 57 50 68 69 99 86 117 129 157 257 306 434 771 1063
145TC
With Motor 78 97 90 108 109 139 126 157 169 197 297 346 474 811 1103
Without Motor 41 60 52 71 84 102 102 120 142 160 264 321 387 449 663 784 971 1077
182TC
With Motor 96 115 107 126 139 157 157 175 197 215 319 376 442 504 718 839 1026 1132
Without Motor 41 60 52 71 84 102 102 120 142 160 264 321 387 449 663 784 971 1077
184TC
With Motor 118 137 129 148 161 179 179 197 219 237 341 398 464 526 740 861 1048 1154
Without Motor 84 102 142 264 321 387 663 784 984 1077
213TC
With Motor 200 218 258 380 437 503 779 900 1100 1193
Without Motor 84 102 142 264 321 387 663 784 984 1077
215TC
With Motor 241 259 299 421 478 544 820 941 1141 1234
Without Motor 142 264 387 663 984 1077
254TC
With Motor 425 547 670 946 1267 1360
MOTORIZED

Without Motor 142 264 387 663 984 1077

256TC
With Motor 448 570 693 969 1290 1383
Without Motor 422 698 984
284TC
With Motor 851 1127 1413
Without Motor 422 698 984
286TC
With Motor 868 1144 1430
Without Motor 422 698 997
324TC
With Motor 945 1221 1520
Without Motor 422 698 997
326TC
With Motor 1072 1348 1647
Without Motor 997
364TC
With Motor 1713
Without Motor 997
365TC
With Motor 1836
Without Motor 1028
404TC
With Motor 2087
Without Motor 1028
405TC
With Motor 2228

91
 SERIES K

Product Safety Information

IMPORTANT
General - The following information is important in ensuring safety. It must be brought to the attention of personnel involved in the selection of
the equipment, those responsible for the design of the machinery in which it is to be incorporated and those involved in its installation, use and
maintenance.

The equipment will operate safely provided it is selected, installed, used and maintained properly. As with any power transmission equipment
proper precautions must be taken as indicated in the following paragraphs, to ensure safety.

Potential Hazards - these are not necessarily listed in any order of severity as the degree of danger varies in individual circumstances. It is
important therefore that the list is studied in its entirety:-

1) Fire/Explosion
(a) Oil mists and vapour are generated within gear units. It is therefore dangerous to use naked lights in the proximity of gearbox openings,
due to the risk of fire or explosion.
(b) In the event of fire or serious overheating (over 300 oC), certain materials (rubber, plastics, etc.) may decompose and produce fumes.
Care should be taken to avoid exposure to the fumes, and the remains of burned or overheated plastic/rubber materials should be handled
with rubber gloves.

2) Guards - Rotating shafts and couplings must be guarded to eliminate the possibility of physical contact or entanglement of clothing. It should
be of rigid construction and firmly secured.

3) Noise - High speed gearboxes and gearbox driven machinery may produce noise levels which are damaging to the hearing with prolonged
exposure. Ear defenders should be provided for personnel in these circumstances. Reference should be made to the Department of
Employment Code of Practice for reducing exposure of employed persons to noise.

4) Lifting - Where provided (on larger units) only the lifting points or eyebolts must be used for lifting operations (see maintenance manual or
general arrangement drawing for lifting point positions). Failure to use the lifting points provided may result in personal injury and/or damage
to the product or surrounding equipment. Keep clear of raised equipment.

5) Lubricants and Lubrication

(a) Prolonged contact with lubricants can be detrimental to the skin. The manufacturer's instruction must be followed when handling
lubricants.
(b) The lubrication status of the equipment must be checked before commissioning. Read and carry out all instructions on the lubricant plate
and in the installation and maintenance literature. Heed all warning tags. Failure to do so could result in mechanical damage and in
extreme cases risk of injury to personnel.

6) Electrical Equipment - Observe hazard warnings on electrical equipment and isolate power before working on the gearbox or associated
equipment, in order to prevent the machinery being started.

7) Installation, Maintenance and Storage

(a) In the event that equipment is to be held in storage, for a period exceeding 6 months, prior to installation or commissioning, application
engineering must be consulted regarding special preservation requirements. Unless otherwise agreed, equipment must be stored in a
building protected from extremes of temperature and humidity to prevent deterioration.
The rotating components (gears and shafts) must be turned a few revolutions once a month (to prevent bearings brinelling).
(b) External gearbox components may be supplied with preservative materials applied, in the form of a "waxed" tape overwrap or wax film
preservative. Gloves should be worn when removing these materials. The former can be removed manually, the latter using white spirit as
a solvent.

Preservatives applied to the internal parts of the gear units do not require removal prior to operation.
(c) Installation must be performed in accordance with the manufacturer's instructions and be undertaken by suitably qualified personnel.
(d) Before working on a gearbox or associated equipment, ensure that the load has been removed from the system to eliminate the
possibility of any movement of the machinery and isolate power supply. Where necessary, provide mechanical means to ensure the
machinery cannot move or rotate. Ensure removal of such devices after work is complete.
(e) Ensure the proper maintenance of gearboxes in operation. Use only the correct tools and approved spare parts for repair and
maintenance. Consult the Maintenance Manual before dismantling or performing maintenance work.

8) Hot Surfaces and Lubricants

(a) During operation, gear units may become sufficiently hot to cause skin burns. Care must be taken to avoid accidental contact.

(b) After extended running the lubricant in gear units and lubrication systems may reach temperatures sufficient to cause burns. Allow
equipment to cool before servicing or performing adjustments.

9) Selection and Design

(a) Where gear units provide a backstop facility, ensure that back-up systems are provided if failure of the backstop device would endanger
personnel or result in damage.
(b) The driving and driven equipment must be correctly selected to ensure that the complete machinery installation will perform satisfactorily,
avoiding system critical speeds, system torsional vibration, etc.
(c) The equipment must not be operated in an environment or at speeds, powers, torques or with external loads beyond those for which it was
designed.
(d) As improvements in design are being made continually the contents of this catalogue are not to be regarded as binding in detail, and
drawings and capacities are subject to alterations without notice.

The above guidance is based on the current state of knowledge and our best assessment of the potential hazards in the operation of
the gear units.

Any further information or clarification required may be obtained by contacting an Application Engineer.
 SERIES K
Contacts
AUSTRALIA EUROPE ITALY THAILAND
David Brown Gear Benzler TBA BV David Brown David Brown (Thailand) Ltd
Industries Ltd Jachthavenweg 2 Hydraulics Italia S.R.L. 700/43 Moo 6
13-19 Franklin Avenue NL-5928 NT Venlo Via Del Costruttore, 64 Amata Nakorn Industrial Estate
Bulli, NSW 2516 41058 – Vignola (MO) Tumbol Klongtumru
Australia Netherlands & the rest of Europe Italy Muang,
Tel: +31 77 324 59 00 Chonburi
Tel: +61 2 4283 0300 Fax: +31 77 324 59 01 Tel: +39 059 770 0411 20000
Fax: +61 2 4283 0333 Fax: +39 059 770 0425 Thailand
Austria
Tel: +43 7 229 618 91 Tel: +66 3845 9044
CHINA Fax: +43 7 229 618 84 SOUTH AFRICA Fax: +66 3821 3655

David Brown Gear Systems Germany David Brown

Trading (Shanghai) Co. Ltd Tel: 0800 350 40 00 Gear Industries Ltd UNITED KINGDOM
No. 218 Xi Zhang South Road, Fax: 0800 350 40 01 12 Birmingham Street,
Silver Tower, Suite 1204B Benoni Industrial David Brown
Shanghai 200021 P.R.China 1500 Gear Systems Ltd
FINLAND South Africa Park Road
Tel: +86 21 53966 555 Lockwood, Huddersfield
Fax: +86 21 53966 913 Oy Benzler AB Tel: +27 11 748 0000 West Yorkshire, HD4 5DD
Vanha Talvitie 3C Fax: +27 11 421 2553
FI-00580 Helsingfors, Tel: +44 (0) 1484 465 610
DENMARK Finland Fax: +44 (0) 1484 465 586
SWEDEN & NORWAY
Benzler Transmission A/S Tel: +358 9 340 1716
Fuglebævej 3D Fax: +358 9 340 1761 AB Benzlers USA
DK-2770 Kastrup, Box 922 (Landskronavägen 1)
Danmark 251 09 Helsingborg Cone Drive
FRANCE Sweden 240 East 12th Street
Tel: +45 36 34 03 00 Traverse City
Fax: +45 36 77 02 42 WECO Transmissions SA Tel: +46 42 18 68 00 Michigan
Fax: +46 42 21 88 03 49684
Tel: +333 8937 0113 USA
Fax: +333 8937 3936
Tel: +1 888 994 2663
Fax: +1 888 907 2663

www.davidbrown.com
www.benzlers.com
www.davidbrown.com