Scribd
Upload
138 views3 pages

Dynojet Power Commander Iiiusb Honda cbr1000 rr08

This document provides installation instructions for the Power Commander on a 2008 Honda CBR1000RR, including a parts list and detailed steps for installation. Key steps include removing the main and passenger seats, fuel tank cover, and airbox, as well as connecting the Power Commander to the stock wiring harness and throttle position sensor. It emphasizes the importance of turning off the ignition before starting the installation and provides contact information for Dynojet Research.

Uploaded by

Luis Ramon Arguello Real
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
138 views3 pages

Dynojet Power Commander Iiiusb Honda cbr1000 rr08

This document provides installation instructions for the Power Commander on a 2008 Honda CBR1000RR, including a parts list and detailed steps for installation. Key steps include removing the main and passenger seats, fuel tank cover, and airbox, as well as connecting the Power Commander to the stock wiring harness and throttle position sensor. It emphasizes the importance of turning off the ignition before starting the installation and provides contact information for Dynojet Research.

Uploaded by

Luis Ramon Arguello Real
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

2008 Honda CBR1000RR

Installation Instructions

Parts List Button Adjustment Display

1 Power Commander
1 USB Cable
1 CD-ROM
1 Installation Guide
1 Power Adapter
2 Power Commander Decals
2 Dynojet Decals
2 Velcro® Strip
1 Alcohol Swab Faceplate Buttons

Expansion Port USB Port

The ignition MUST be turned


OFF before installation!

You can also download the Power


Commander software and latest maps
from our web site at:
www.powercommander.com

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com

i132-411 www.powercommander.com 2008 Honda CBR1000RR - PCIII USB - 1


1 Remove the main seat and the passen-
ger seat.
2 Remove the fuel tank cover.
3 Lift the fuel tank up or remove.
4 Unbolt the airbox from the throttle
Fig. A

bodies. The airbox does not need to


be totally removed to install PCIII.
5 Mount the PCIII in the tail section
using the supplied velcro (Fig. A)
6 Route the PCIII harness down the left
side of the bike.

7 Unplug the stock wiring harness from


each of the LOWER injectors
(Fig. B).
Fig. B

The lower injectors are located on the


throttle bodies.

Unplug harness

8 Connect the PCIII in-line of the stock


Fig. C

wiring harness and each injector


(Fig. C).

i132-411 www.powercommander.com 2008 Honda CBR1000RR - PCIII USB - 2


With the air box moved out of the
way you can access the Throttle
Position Sensor.
Fig. D

9 Unplug the stock TPS from the right


hand side of the throttle body (Fig. D)

Unplug TPS

Stock connector

10 Plug the PCIII harness in-line of the


Fig. E

stock TPS and wiring harness (Fig. E)

PCIII connectors

11 Attach the gound wire from the PCIII


to the negative side of the battery
Ground wire from PCIII (Fig. F).
Fig. F

12 Reinstall the air box and fuel tank.


Make sure the tank does not pinch the
PCIII wiring harness.

i132-411 www.powercommander.com 2008 Honda CBR1000RR - PCIII USB - 3

You might also like