SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

1. PRODUCT AND COMPANY IDENTIFICATION

Product name : AeroShell Grease 7

Product code : 001A0065

Manufacturer or supplier's details

Supplier : Shell Eastern Petroleum (Pte) Ltd
(196000089G)
The Metropolis Tower 1,
9 North Buona Vista Drive, #07-01
Singapore 138588
Singapore
Telephone : (+65) 62632975
Telefax : (+65) 62632049

Emergency telephone : +65 6263 2975

number
Email Contact for Safety : If you have any enquiries about the content of this SDS
Data Sheet please email [email protected]

Recommended use of the chemical and restrictions on use

Recommended use : Synthetic grease for aircraft., For further details consult the
AeroShell Book on www.shell.com/aviation.

Restrictions on use : This product must be used, handled and applied in

accordance with the requirements of the equipment
manufacturer's manuals, bulletins and other documentation.

2. HAZARDS IDENTIFICATION

GHS Classification
Skin sensitisation : Category 1
Long-term (chronic) aquatic : Category 3
hazard
GHS label elements
Hazard pictograms :

Signal word : Warning

Hazard statements : PHYSICAL HAZARDS:

Not classified as a physical hazard under GHS criteria.
HEALTH HAZARDS:
H317 May cause an allergic skin reaction.
ENVIRONMENTAL HAZARDS:
H412 Harmful to aquatic life with long lasting effects.

1 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

Precautionary statements :
Prevention:
P273 Avoid release to the environment.
P280 Wear protective gloves/ protective clothing/ eye
protection/ face protection.

Response:
P302 + P352 IF ON SKIN: Wash with plenty of water and soap.
P333 + P313 If skin irritation or rash occurs: Get medical
advice/ attention.

Storage:
No precautionary phrases.

Disposal:
P501 Dispose of contents/ container to an approved waste
disposal plant.

Hazardous components which must be listed on the label:

Contains N-phenyl-1-naphthylamine.
Other hazards which do not result in classification
Prolonged or repeated skin contact without proper cleaning can clog the pores of the skin
resulting in disorders such as oil acne/folliculitis.Used oil may contain harmful impurities.High-
pressure injection under the skin may cause serious damage including local necrosis.Not
classified as flammable but will burn.

3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical nature : Synthetic oil grease thickened with clay, containing additives.

Hazardous components
Chemical name CAS-No. Classification Concentration
[%]
N-phenyl-1- 90-30-2 Acute Tox.4; H302 1- 3
naphthylamine Skin Sens.1B; H317
STOT RE2; H373
Aquatic Acute1;
H400
Aquatic Chronic1;
H410
Phenothiazine 92-84-2 Acute Tox.4; H302 0.1 - 0.9
Skin Sens.1B; H317
STOT RE2; H373
Aquatic Acute1;
H400
Aquatic Chronic1;
H410
Triazole derivative 80584-90-3 Skin Irrit.2; H315 0.1 - 0.9
Skin Sens.1B; H317
Aquatic Chronic1;

2 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

H410
Aquatic Acute1;
H400
For explanation of abbreviations see section 16.

4. FIRST-AID MEASURES

If inhaled : No treatment necessary under normal conditions of use.

If symptoms persist, obtain medical advice.

In case of skin contact : Remove contaminated clothing. Flush exposed area with
water and follow by washing with soap if available.
If persistent irritation occurs, obtain medical attention.

When using high pressure equipment, injection of product

under the skin can occur. If high pressure injuries occur, the
casualty should be sent immediately to a hospital. Do not wait
for symptoms to develop.
Obtain medical attention even in the absence of apparent
wounds.

In case of eye contact : Flush eye with copious quantities of water.

Remove contact lenses, if present and easy to do. Continue
rinsing.
If persistent irritation occurs, obtain medical attention.

If swallowed : In general no treatment is necessary unless large quantities

are swallowed, however, get medical advice.

Most important symptoms : Skin sensitisation (allergic skin reaction) signs and symptoms
and effects, both acute and may include itching and/or a rash.
delayed Oil acne/folliculitis signs and symptoms may include formation
of black pustules and spots on the skin of exposed areas.
Ingestion may result in nausea, vomiting and/or diarrhoea.

Local necrosis is evidenced by delayed onset of pain and

tissue damage a few hours following injection.

Protection of first-aiders : When administering first aid, ensure that you are wearing the
appropriate personal protective equipment according to the
incident, injury and surroundings.

Notes to physician : Treat symptomatically.

High pressure injection injuries require prompt surgical

intervention and possibly steroid therapy, to minimise tissue
damage and loss of function.
Because entry wounds are small and do not reflect the
seriousness of the underlying damage, surgical exploration to
determine the extent of involvement may be necessary. Local
anaesthetics or hot soaks should be avoided because they
can contribute to swelling, vasospasm and ischaemia. Prompt

3 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

surgical decompression, debridement and evacuation of
foreign material should be performed under general
anaesthetics, and wide exploration is essential.

5. FIRE-FIGHTING MEASURES

Suitable extinguishing media : Foam, water spray or fog. Dry chemical powder, carbon
dioxide, sand or earth may be used for small fires only.

Unsuitable extinguishing : Do not use water in a jet.

media

Specific hazards during : Hazardous combustion products may include:

firefighting A complex mixture of airborne solid and liquid particulates and
gases (smoke).
Carbon monoxide may be evolved if incomplete combustion
occurs.
Unidentified organic and inorganic compounds.

Specific extinguishing : Use extinguishing measures that are appropriate to local

methods circumstances and the surrounding environment.

Special protective equipment : Proper protective equipment including chemical resistant

for firefighters gloves are to be worn; chemical resistant suit is indicated if
large contact with spilled product is expected. Self-Contained
Breathing Apparatus must be worn when approaching a fire in
a confined space. Select fire fighter's clothing approved to
relevant Standards (e.g. Europe: EN469).

6. ACCIDENTAL RELEASE MEASURES

Personal precautions, : Avoid contact with skin and eyes.

protective equipment and
emergency procedures
Environmental precautions : Use appropriate containment to avoid environmental
contamination. Prevent from spreading or entering drains,
ditches or rivers by using sand, earth, or other appropriate
barriers.

Methods and materials for : Shovel into a suitable clearly marked container for disposal or
containment and cleaning up reclamation in accordance with local regulations.

Additional advice : For guidance on selection of personal protective equipment

see Chapter 8 of this Safety Data Sheet.
For guidance on disposal of spilled material see Chapter 13 of
this Safety Data Sheet.

7. HANDLING AND STORAGE

4 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

General Precautions : Use local exhaust ventilation if there is risk of inhalation of
vapours, mists or aerosols.
Use the information in this data sheet as input to a risk
assessment of local circumstances to help determine
appropriate controls for safe handling, storage and disposal of
this material.

Advice on safe handling : Avoid prolonged or repeated contact with skin.

Avoid inhaling vapour and/or mists.
When handling product in drums, safety footwear should be
worn and proper handling equipment should be used.
Properly dispose of any contaminated rags or cleaning
materials in order to prevent fires.

Avoidance of contact : Strong oxidising agents.

Storage
Storage temperature : -50 - 50 °C

Other data : Keep container tightly closed and in a cool, well-ventilated

place.
Use properly labeled and closable containers.

Packaging material : Suitable material: For containers or container linings, use mild
steel or high density polyethylene.
Unsuitable material: PVC.

Container Advice : Polyethylene containers should not be exposed to high

temperatures because of possible risk of distortion.

8. EXPOSURE CONTROLS AND PERSONAL PROTECTION

Components with workplace control parameters

Components CAS-No. Value type Control Basis
(Form of parameters /
exposure) Permissible
concentration
Phenothiazine 92-84-2 PEL (long 5 mg/m3 SG OEL
term)
Phenothiazine 92-84-2 TWA 5 mg/m3 ACGIH
Biological occupational exposure limits
No biological limit allocated.

Monitoring Methods
Monitoring of the concentration of substances in the breathing zone of workers or in the general
workplace may be required to confirm compliance with an OEL and adequacy of exposure
controls. For some substances biological monitoring may also be appropriate.
Validated exposure measurement methods should be applied by a competent person and
samples analysed by an accredited laboratory.
Examples of sources of recommended exposure measurement methods are given below or
contact the supplier. Further national methods may be available.

5 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

National Institute of Occupational Safety and Health (NIOSH), USA: Manual of Analytical Methods
http://www.cdc.gov/niosh/

Occupational Safety and Health Administration (OSHA), USA: Sampling and Analytical Methods
http://www.osha.gov/

Health and Safety Executive (HSE), UK: Methods for the Determination of Hazardous Substances
http://www.hse.gov.uk/

Institut für Arbeitsschutz Deutschen Gesetzlichen Unfallversicherung (IFA) , Germany

http://www.dguv.de/inhalt/index.jsp

L'Institut National de Recherche et de Securité, (INRS), France http://www.inrs.fr/accueil

Engineering measures : The level of protection and types of controls necessary will
vary depending upon potential exposure conditions. Select
controls based on a risk assessment of local circumstances.
Appropriate measures include:
Adequate ventilation to control airborne concentrations.

Where material is heated, sprayed or mist formed, there is

greater potential for airborne concentrations to be generated.

General Information:
Define procedures for safe handling and maintenance of
controls.
Educate and train workers in the hazards and control
measures relevant to normal activities associated with this
product.
Ensure appropriate selection, testing and maintenance of
equipment used to control exposure, e.g. personal protective
equipment, local exhaust ventilation.
Drain down system prior to equipment break-in or
maintenance.
Retain drain downs in sealed storage pending disposal or
subsequent recycle.
Always observe good personal hygiene measures, such as
washing hands after handling the material and before eating,
drinking, and/or smoking. Routinely wash work clothing and
protective equipment to remove contaminants. Discard
contaminated clothing and footwear that cannot be cleaned.
Practice good housekeeping.

Due to the product's semi-solid consistency, generation of

mists and dusts is unlikely to occur.

Personal protective equipment

Protective measures
Personal protective equipment (PPE) should meet recommended national standards. Check with
PPE suppliers.

Respiratory protection : No respiratory protection is ordinarily required under normal

6 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

conditions of use.
In accordance with good industrial hygiene practices,
precautions should be taken to avoid breathing of material.
If engineering controls do not maintain airborne
concentrations to a level which is adequate to protect worker
health, select respiratory protection equipment suitable for the
specific conditions of use and meeting relevant legislation.
Check with respiratory protective equipment suppliers.
Where air-filtering respirators are suitable, select an
appropriate combination of mask and filter.
Select a filter suitable for the combination of organic gases
and vapours [Type A/Type P boiling point >65°C (149°F)].

Hand protection
Remarks : Where hand contact with the product may occur the use of
gloves approved to relevant standards (e.g. Europe: EN374,
US: F739) made from the following materials may provide
suitable chemical protection. PVC, neoprene or nitrile rubber
gloves Suitability and durability of a glove is dependent on
usage, e.g. frequency and duration of contact, chemical
resistance of glove material, dexterity. Always seek advice
from glove suppliers. Contaminated gloves should be
replaced. Personal hygiene is a key element of effective hand
care. Gloves must only be worn on clean hands. After using
gloves, hands should be washed and dried thoroughly.
Application of a non-perfumed moisturizer is recommended.

For continuous contact we recommend gloves with

breakthrough time of more than 240 minutes with preference
for > 480 minutes where suitable gloves can be identified. For
short-term/splash protection we recommend the same but
recognize that suitable gloves offering this level of protection
may not be available and in this case a lower breakthrough
time maybe acceptable so long as appropriate maintenance
and replacement regimes are followed. Glove thickness is not
a good predictor of glove resistance to a chemical as it is
dependent on the exact composition of the glove material.
Glove thickness should be typically greater than 0.35 mm
depending on the glove make and model.

Eye protection : Wear full face shield if splashes are likely to occur.

Skin and body protection : Wear chemical resistant gloves/gauntlets and boots. Where
risk of splashing, also wear an apron.

Thermal hazards : Not applicable

Environmental exposure controls

General advice : Take appropriate measures to fulfill the requirements of
relevant environmental protection legislation. Avoid
contamination of the environment by following advice given in
Chapter 6. If necessary, prevent undissolved material from
being discharged to waste water. Waste water should be

7 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

treated in a municipal or industrial waste water treatment plant
before discharge to surface water.
Local guidelines on emission limits for volatile substances
must be observed for the discharge of exhaust air containing
vapour.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance : Semi-solid at ambient temperature.

Colour : light brown

Odour : Slight hydrocarbon
Odour Threshold : Data not available
pH : Not applicable
Drop point : >= 260 °C / >= 500 °FMethod: Unspecified

Initial boiling point and boiling : Data not available

range
Flash point : Not applicable
Evaporation rate : Data not available
Flammability (solid, gas) : Data not available

Upper explosion limit : Typical 10 %(V)

Lower explosion limit : Typical 1 %(V)

Vapour pressure : < 0.5 Pa (20 °C / 68 °F)

estimated value(s)
Relative vapour density : > 1estimated value(s)
Relative density : 0.966 (15 °C / 59 °F)

Density : 966 kg/m3 (15.0 °C / 59.0 °F)

Method: Unspecified

Solubility(ies)
Water solubility : negligible
Solubility in other solvents : Data not available

Partition coefficient: n- : log Pow: > 6(based on information on similar products)

octanol/water
Auto-ignition temperature : > 320 °C / 608 °F

Decomposition temperature : Data not available

Viscosity

8 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

Viscosity, dynamic : Data not available
Viscosity, kinematic : Not applicable
Explosive properties : Not classified

Oxidizing properties : Data not available

Conductivity : This material is not expected to be a static accumulator.

10. STABILITY AND REACTIVITY

Reactivity : The product does not pose any further reactivity hazards in
addition to those listed in the following sub-paragraph.

Chemical stability : Stable.

Possibility of hazardous : Reacts with strong oxidising agents.

reactions
Conditions to avoid : Extremes of temperature and direct sunlight.

Incompatible materials : Strong oxidising agents.

Hazardous decomposition : No decomposition if stored and applied as directed.

products

11. TOXICOLOGICAL INFORMATION

Basis for assessment : Information given is based on data on the components and
the toxicology of similar products.Unless indicated otherwise,
the data presented is representative of the product as a
whole, rather than for individual component(s).

Information on likely routes of : Skin and eye contact are the primary routes of exposure
exposure although exposure may occur following accidental ingestion.

Acute toxicity
Product:
Acute oral toxicity : LD50 rat: > 5,000 mg/kg
Remarks: Low toxicity:
Based on available data, the classification criteria are not met.

Acute inhalation toxicity : Remarks: Based on available data, the classification criteria
are not met.

Acute dermal toxicity : LD50 Rabbit: > 5,000 mg/kg

Remarks: Low toxicity:
Based on available data, the classification criteria are not met.

9 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

Skin corrosion/irritation
Product:
Remarks: Slightly irritating to skin., Prolonged or repeated skin contact without proper cleaning
can clog the pores of the skin resulting in disorders such as oil acne/folliculitis., Based on
available data, the classification criteria are not met.

Serious eye damage/eye irritation

Product:
Remarks: Slightly irritating to the eye., Based on available data, the classification criteria are not
met.

Respiratory or skin sensitisation

Product:
Remarks: Expected to be a skin sensitizer.

Components:
N-phenyl-1-naphthylamine:
Remarks: May cause an allergic skin reaction in sensitive individuals.

Phenothiazine:
Remarks: May cause an allergic skin reaction in sensitive individuals.

Triazole derivative:
Remarks: May cause an allergic skin reaction in sensitive individuals.

Germ cell mutagenicity

Product:
: Remarks: Non mutagenic, Based on available data, the
classification criteria are not met.
Carcinogenicity
Product:

Remarks: Not a carcinogen., Based on available data, the classification criteria are not met.

Material GHS/CLP Carcinogenicity Classification

N-phenyl-1-naphthylamine No carcinogenicity classification.
Phenothiazine No carcinogenicity classification.
Triazole derivative No carcinogenicity classification.

10 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

Reproductive toxicity

Product:
:
Remarks: Not a developmental toxicant., Does not impair
fertility., Based on available data, the classification criteria are
not met.

STOT - single exposure

Product:
Remarks: Based on available data, the classification criteria are not met.

STOT - repeated exposure

Product:
Remarks: Based on available data, the classification criteria are not met.

Aspiration toxicity
Product:
Not an aspiration hazard.

Further information
Product:
Remarks: Used grease may contain harmful impurities that have accumulated during use. The
concentration of such harmful impurities will depend on use and they may present risks to health
and the environment on disposal., ALL used grease should be handled with caution and skin
contact avoided as far as possible.

Remarks: High pressure injection of product into the skin may lead to local necrosis if the
product is not surgically removed.

Remarks: Slightly irritating to respiratory system.

12. ECOLOGICAL INFORMATION

Basis for assessment : Ecotoxicological data have not been determined specifically
for this product.
Information given is based on a knowledge of the components
and the ecotoxicology of similar products.
Unless indicated otherwise, the data presented is
representative of the product as a whole, rather than for
individual component(s).(LL/EL/IL50 expressed as the
nominal amount of product required to prepare aqueous test
extract).

Ecotoxicity

11 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

Product:
Toxicity to fish (Acute :
toxicity) Remarks: LL/EL/IL50 10-100 mg/l
Harmful

Toxicity to crustacean (Acute :

toxicity) Remarks: LL/EL/IL50 10-100 mg/l
Harmful

Toxicity to algae/aquatic :
plants (Acute toxicity) Remarks: LL/EL/IL50 10-100 mg/l
Harmful

Toxicity to fish (Chronic : Remarks: Data not available

toxicity)
Toxicity to crustacean : Remarks: Data not available
(Chronic toxicity)
Toxicity to microorganisms : Remarks: Data not available
(Acute toxicity)

Components:
N-phenyl-1-naphthylamine :
M-Factor : 1
Triazole derivative :
M-Factor : 1
Persistence and degradability
Product:
Biodegradability : Remarks: Not readily biodegradable., Major constituents are
inherently biodegradable, but contains components that may
persist in the environment.

Bioaccumulative potential
Product:
Bioaccumulation : Remarks: Contains components with the potential to
bioaccumulate.

Partition coefficient: n- : log Pow: > 6Remarks: (based on information on similar

octanol/water products)
Mobility in soil
Product:
Mobility : Remarks: Semi-solid under most environmental conditions., If
it enters soil, it will adsorb to soil particles and will not be
mobile.
Remarks: Floats on water.
Other adverse effects
no data available
Product:
Additional ecological : Does not have ozone depletion potential, photochemical
information ozone creation potential or global warming potential., Product

12 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

is a mixture of non-volatile components, which will not be
released to air in any significant quantities under normal
conditions of use.
Poorly soluble mixture., Causes physical fouling of aquatic
organisms.

13. DISPOSAL CONSIDERATIONS

Disposal methods
Waste from residues : Recover or recycle if possible.
It is the responsibility of the waste generator to determine the
toxicity and physical properties of the material generated to
determine the proper waste classification and disposal
methods in compliance with applicable regulations.
Do not dispose into the environment, in drains or in water
courses

Waste product should not be allowed to contaminate soil or

ground water, or be disposed of into the environment.
Waste, spills or used product is dangerous waste.

Contaminated packaging : Dispose in accordance with prevailing regulations, preferably

to a recognized collector or contractor. The competence of
the collector or contractor should be established beforehand.
Disposal should be in accordance with applicable regional,
national, and local laws and regulations.

Local legislation
Remarks : Disposal should be in accordance with applicable regional,
national, and local laws and regulations.

14. TRANSPORT INFORMATION

International Regulations
ADR
Not regulated as a dangerous good
IATA-DGR
Not regulated as a dangerous good
IMDG-Code
Not regulated as a dangerous good
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable for product as supplied. MARPOL Annex 1 rules apply for bulk shipments by sea.

Special precautions for user

Remarks : Special Precautions: Refer to Chapter 7, Handling & Storage,
for special precautions which a user needs to be aware of or

13 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

needs to comply with in connection with transport.

15. REGULATORY INFORMATION

Safety, health and environmental regulations/legislation specific for the substance or

mixture
Local Regulations

Workplace Safety and Health Act & Workplace This product is subject to the SDS, Labelling,
Safety and Health (General Provision) PEL and other requirements in the Act/
Regulations Regulations.

Fire Safety Act and Fire Safety (Petroleum & This product is not subject to the requirements
Flammable Materials) Regulations in the Act/Regulations.

Maritime and Port Authority of Singapore This product is not subject to the requirements
(Dangerous Goods, Petroleum and Explosives) in the Act/Regulations.
Regulations

Environmental Protection and Management Act This product is not subject to control under this
and Environmental Protection and Act/ Regulation.
Management (Hazardous Substances)
Regulations
The regulatory information is not intended to be comprehensive. Other regulations may apply to
this material.
Other international regulations
The components of this product are reported in the following inventories:
EINECS : Not established.
TSCA : All components listed.

16. OTHER INFORMATION

Full text of H-Statements

H302 Harmful if swallowed.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H373 May cause damage to organs through prolonged or repeated exposure.
H400 Very toxic to aquatic life.
H410 Very toxic to aquatic life with long lasting effects.
Full text of other abbreviations
Acute Tox. Acute toxicity
Aquatic Acute Short-term (acute) aquatic hazard
Aquatic Chronic Long-term (chronic) aquatic hazard
Skin Irrit. Skin irritation
Skin Sens. Skin sensitisation
STOT RE Specific target organ toxicity - repeated exposure

14 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

AIIC -Australian Inventory of Industrial Chemicals; ANTT - National Agency for Transport by Land
of Brazil; ASTM - American Society for the Testing of Materials; bw - Body weight; CMR -
Carcinogen, Mutagen or Reproductive Toxicant; CPR - Controlled Products Regulations; DIN -
Standard of the German Institute for Standardisation; DSL - Domestic Substances List (Canada);
ECx - Concentration associated with x% response; ELx - Loading rate associated with x%
response; EmS - Emergency Schedule; ENCS - Existing and New Chemical Substances (Japan);
ErCx - Concentration associated with x% growth rate response; ERG - Emergency Response
Guide; GHS - Globally Harmonized System; GLP - Good Laboratory Practice; IARC -
International Agency for Research on Cancer; IATA - International Air Transport Association; IBC
- International Code for the Construction and Equipment of Ships carrying Dangerous Chemicals
in Bulk; IC50 - Half maximal inhibitory concentration; ICAO - International Civil Aviation
Organization; IECSC - Inventory of Existing Chemical Substances in China; IMDG - International
Maritime Dangerous Goods; IMO - International Maritime Organization; ISHL - Industrial Safety
and Health Law (Japan); ISO - International Organisation for Standardization; KECI - Korea
Existing Chemicals Inventory; LC50 - Lethal Concentration to 50 % of a test population; LD50 -
Lethal Dose to 50% of a test population (Median Lethal Dose); MARPOL - International
Convention for the Prevention of Pollution from Ships; n.o.s. - Not Otherwise Specified; Nch -
Chilean Norm; NO(A)EC - No Observed (Adverse) Effect Concentration; NO(A)EL - No Observed
(Adverse) Effect Level; NOELR - No Observable Effect Loading Rate; NOM - Official Mexican
Norm; NTP - National Toxicology Program; NZIoC - New Zealand Inventory of Chemicals; OECD
- Organization for Economic Co-operation and Development; OPPTS - Office of Chemical Safety
and Pollution Prevention; PBT - Persistent, Bioaccumulative and Toxic substance; PICCS -
Philippines Inventory of Chemicals and Chemical Substances; (Q)SAR - (Quantitative) Structure
Activity Relationship; REACH - Regulation (EC) No 1907/2006 of the European Parliament and of
the Council concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals;
SADT - Self-Accelerating Decomposition Temperature; SDS - Safety Data Sheet; TCSI - Taiwan
Chemical Substance Inventory; TDG - Transportation of Dangerous Goods; TSCA - Toxic
Substances Control Act (United States); UN - United Nations; UNRTDG - United Nations
Recommendations on the Transport of Dangerous Goods; vPvB - Very Persistent and Very
Bioaccumulative; WHMIS - Workplace Hazardous Materials Information System

Further information
Training advice : Provide adequate information, instruction and training for
operators.

Other information : A vertical bar (|) in the left margin indicates an amendment
from the previous version.

Sources of key data used to : The quoted data are from, but not limited to, one or more
compile the Safety Data sources of information (e.g. toxicological data from Shell
Sheet Health Services, material suppliers’ data, CONCAWE, EU
IUCLID date base, EC 1272 regulation, etc).

The information provided in this Safety Data Sheet is correct to the best of our knowledge,
information and belief at the date of its publication. The information given is designed only as a
guidance for safe handling, use, processing, storage, transportation, disposal and release and is
not to be considered a warranty or quality specification. The information relates only to the
specific material designated and may not be valid for such material used in combination with any
other materials or in any process, unless specified in the text.

SG / EN

15 / 16 800001016180
SG
SAFETY DATA SHEET

AeroShell Grease 7

Version 2.1 Revision Date 19.03.2019 Print Date 20.03.2019

16 / 16 800001016180
SG