ISO 9001:2008 – Cert. Nr.

50 100 1436
ISO 14001:2004 – Cert. Nr. 50 100 1435

Rev. 01 dated 21/09/2017

DATA SHEET Page 1/2

STAG 11
Water based release agent for
Extrusion of metals and alloys

______________________________________________________
DESCRIPTION Compound of innovative release agents, in aqueous solution, formulated
for the treatment of dummy block and billet in Extrusion of metals and
alloys. It has been especially studied for Aluminium Extrusion.

______________________________________________________
TECHNICAL DETAILS Physical state: liquid Density (20°C): appr.1.20 g/ml
Colour: light blue Flammability: non-flammable
Odour: very mild Solubility: water
pH (pure): approx. 9.0

SPECIFICATIONS TEST METHOD STANDARD LIMIT

Appearance Visual (AO/1) light blue

pH (pure) Potentiom. (PM/1) 8.0 - 9.5
Density (20°C) Densim. (DE/2) 1.10 – 1.25 g/ml

______________________________________________________
CHARACTERISTICS Very high releasing power at high process temperature: the product
forms a very thermal resistant film on the treated surfaces.
The Leidenfrost effect is greatly reduced, making possible the
instantaneous deposition of a uniform and continuous film on hot
surfaces with excellent adhesion.
The films formed by STAG 11 is soluble in water and is thus easily
washed out by a jet of water, leaving the machine perfectly clean.
STAG 11 is a non-flammable product. It has an increased protective
and anticorrosive power.

BARALDI S.r.l. – Via Lombardia, 2/I – 2/L – 40024 OSTERIA GRANDE – CASTEL S. PIETRO (BO) ITALY
Tel. +39.051.946.994 r.a. – Fax +39.051.946.988 – E-mail: [email protected] - www.baraldi.com
STAG 11

Rev. 01 dated 21/09/2017

Page 2/2
______________________________________________________
HOW TO USE DILUTION
It is advisable to use the pure product or diluted in water. Sometimes it
may be opportune, in order to optimize the application on the basis of the
spraying equipment and spraying time, to dilute the product.
The maximum suggested dilution ratio is 1:1 (max. 50% of added water).

APPLICATION
General Indications
Spray the pure or diluted product at each cycle, on the dummy block, or
on the surface of the billet that will keep in contact with the dummy
block (or both billet + dummy block). Spray for a time long enough to
cover the whole surface with a homogeneous thin layer of product.
Normally a few seconds of spray are enough. For the application it is
suggested to use systems able to atomize the product.
Starting trials
Apply the product manually by means of a simple sprinkler or better, by
means of a manual pneumatic painting gun.
Standard application
Apply the product well atomized, avoiding excessive pressures that give
rebound of the droplets toward the machine parts.
With spraying device provided with regulation of atomizing air pressure.
Product pressure: between 0.6 and 1.0 bar
Atomizing air pressure: slightly higher, between 0.8 and 1.4 bar.
To find the best application start setting the product pressure at 0.8 bar,
then change the atomizing air pressure till a good atomization is obtained,
without overspray and rebound. If necessary reduce the product pressure.
With spraying device without regulation of atomizing air pressure.
Air pressure must be 0.5 – 1.0 bar higher than product pressure. The
values depend on the distance between spraying nozzles and surface to
treat.
______________________________________________________
STORAGE Avoid long stockage under the sun.
Shelf life: not less than 18 months, in original closed containers.
Keep closed containers.
______________________________________________________
PACKAGING Pail: 20 Kg net
Drum: 220 Kg net
IBC: 1100 Kg net
______________________________________________________
FURTHER INFORMAT. For information regarding safety, transport and disposal refer to the Safety Data
Sheet of the product.
________________________________________________________________________________
The data in this technical information sheet correspond to the properties of the product at the time of the sale and with regard to the
specified application. It is on the responsibility of the user to make sure that the product is suitable for the use to which he intents to
destinate it.

BARALDI S.r.l. – Via Lombardia, 2/I – 2/L – 40024 OSTERIA GRANDE – CASTEL S. PIETRO (BO) ITALY
Tel. +39.051.946.994 r.a. – Fax +39.051.946.988 – E-mail: [email protected] - www.baraldi.com